RG1,5SA Self Adhesive
|
|
- Veronica Mathews
- 5 years ago
- Views:
Transcription
1 Description of Product: Self adhesive membrane with a thickness of 1.5mm, consisting of rubberized bitumen with adhesive additives, glassfiber carrier, removable PP film at bottom and high density polyethylene film at top. Reinforcement: Glassfiber reinforcement gives Rumba excellent dimensional stability especially at hot weather conditions. Surface Finish: Siliconize Removable PP film at bottom and high density polyethylene film at top. Typical Application Areas: Applied on surfaces which are to be protected against water penetration: Roofs- protection of cement roofs, protection of wooden roofs, even with high sloping; protection of ventilated metal roofs. Concrete- Ideal for waterproofing concrete, masonry and wood surfaces where in-service temperatures will not exceed 54 C. Use with Bitumex Primers. Features and Benefits: Eliminated the need for torching or mopping Ensured quick, clean and easy lapping of rolls No open flame on your roof Clean and neat application Safe application 100% UV protected Basic Application Instructions: Applied Cold. Need primer application before membrane application. Surface Preparation and Priming: A fundamental requirement of any bituminous membrane system is that it must provide protection from all weather conditions likely to be experienced during its design life. All individual layers in a bituminous membrane system must be watertight, and together the whole system must be waterproof. Application area should be removed from stains and be smooth. For this purpose, Bitumen Primer needs to be applied on surface before application. Cover primed surfaces with self-adhered roofing membranes the same day.
2 Application of Membrane: Fully Adhered 1- Starting at the roof drains and vertical to the roof slope, apply the self-adhesive membrane without adhering in parallel lines. Unroll onto the below surface for alignment. Do not immediately remove the release sheet. 2. Overlap the membrane next to another along the side lap and the ends. Side overlap creates longitudinal overlap between two sheets. End overlap creates a join between shorter sides of the sheets To overlap at side laps, just remove the PP bant (7.5cm) and apply to the adjacent membrane pratically. Ensure full adherence. Stagger the end joints by a minimum of 61cm. 3.Release the PP film and adhere this part of the self-adhesive membrane to the surface. Relase PP film on the remaining part at a 45 angle to avoid wrinkles in the self-adhesive membrane sheet. 4. Overlap adjacent self-adhesive membrane by 9cm. Overlap end laps by 15cm. Stagger end laps by a minimum of 61cm. Finish with weighted roller to ensure a continuous adherence to the surface.
3 Safety Precaution: Bitumex products must be applied by qualified applicators who have received an adequate training, for the prevention and the protection (in particular for the use of the extinguishers) against accidents caused by the combustible or flammable materials, of liquefied propane gas, open flame and their material of installation. Check the construction and the composition of the systems of roof and the walls before applying. Ensure the cleanliness of the places. Use only proper torching equipment in perfect working order certified by local standard organizations. Use only proper hoses suited for propane gas of less than 15m. Verify and tighten all the connections before the use of the equipment. Do not light the torch if a propane odour is present. Never seek a leak with a flame. Use soapy water. Use a torch whose gas output is adjustable with a stopping device. Follow the specifications, notices and documentations of the manufacturer and site authorities. The wearing of gloves, long sleeves, long trousers, safety boots, helmet and safety glasses is recommended. Do not wear synthetic fabrics. Remove clothing contaminated with solvents. Avoid skin contact. Good working practices, high standarts of personal hygiene and plant cleanliness must be maintained at all times. Whilst using, do not eat, drink or smoke. In the event of any localised changes in appearance or texture of the skin being noticed, medical advice should be sought without delay. Contact with hot product will cause burns. Ensure good ventilation and avoid, as far as reasonably practicable, the inhalation and contact with vapours, mists or fumes which may be generated during use. If such vapour, mists or fumes are generated, their concentration in the workplace air should be controlled to the lowest reasonably practicable level. Avoid contact with eyes. Highly toxic hydrogen sulphide gas may be emitted from hot product and accumulate in enclosed spaces or tanks. Extreme care must therefore be taken during venting of closed spaces which have, at any time contained hot product. Under no circumstances should entry be made in to small enclosures without taking full precautions.
4 Storage: Flashings must be stored in such a way to prevent any creasing, twisting, scratches and other damages of the roof. The materials will be protected adequately and stored permanently away from flames or welding sparks, protected from bad weather and any harmful substances. Keep all membranes upright. 1. Rolls should always be stored and transported at upright position. 2. Membrane pallets should not be stored on top of each other and similarly, heavy loads should never be placed on membrane pallets. 3. Bituminous membranes should be stored at closed areas where room temperature is above +5C. They should never be stored outside as pallets are exposed to direct sun shine and should always be kept away from heat sources. 4. Membrane rolls should not be laid outside if there is no cover on them. High temperature may lead to longitudinal shrinkage and latitudinal expandage at membranes with polyester carrier. For bituminous membranes, recommended shelf-life is 12 months. Later than this date, membrane performance is diminishing. Packaging: Pallets are covered by UV Resistant White Shrinks Roll Size : 1mtx20mt 1,5mm Rolls per pallet: 25Rolls (By Container) and 30Rolls(By Truck)
5 Product Details Unit Tolerance RG1,5SA Modification of Bitumen Reinforcement Upper surface coating Lower surface coating TS EN Test Method Unit SBS Fibre Glass HDPE PP Removable Film Visual defects TS EN none Thickness TS EN mm ±0,2 1,5 Length TS EN m min(-0,03) 20 Width TS EN cm min(-2) 100 Straightness TS EN pass Watertightness (10kPa) TS EN kPa pass Reaction to Fire TS EN E class External Fire Performance ENV NPD Watertightness after stretching TS EN NPD Peel resistance of joints TS EN N/50mm ±30% 38 Water vapour properties TS EN 1931 min Tensile strength (MD/CMD) TS EN N/50mm 400/300 Elongation (MD/CD) TS EN % 2/2 Impact resistance TS EN 12691Mtd.A mm min 700 Tearing resistance (with nail) TS EN N/50mm ±20% 150 Dimensional Stability TS EN % max 0,6 Cold Bending TS EN 1109 C min -10 Flow Resistance TS EN 1110 C min 100 TS EN Impact resistance TS EN 12691Mtd.A min 700 Resistance to Chemicals Cold Bending TS EN 1109 C min -10 Tearing resistance (with nail) TS EN N/50mm ±20% 150 Sheer resistance of joints TS EN N/50mm ±20% 250 Water vapour properties TS EN 1931 min Resistance to static loading TS EN Mtd.B Kg min 5 Tensile strength (MD/CMD) TS EN N/50mm 400/300 Elongation (MD/CD) TS EN % 2/2 Reaction to Fire EN NPD Dangerous Substances none none NPD
6
SPIDER P SPIDER P mineral
The leader in the selfadhesive technology! SPIDER P SPIDER P mineral SPIDER P and SPIDER P MINERAL are excellent quality self-adhesive waterproofing membranes made with ADESO technology, the new compound
More informationSPECIAL SPECIFICATION 3687 Impermeable Liner
1993 Specifications CSJ s 0569-01-043 & 0945-04-025 SPECIAL SPECIFICATION 3687 Impermeable Liner 1. Description. This Item shall govern for the furnishing and installation of the impermeable liner (geomembrane)
More informationEFFISUS BRAZE MEMBRANE
Effisus Braze Membrane EFFISUS BRAZE MEMBRANE Elastomer sheets for facade sealing from Ethylen-Propylen-Dien-Terpolymer (EPDM), homogeneous, cured without fleece-backing. Elastomer sheets for facade waterproofing.
More informationFLAGON PVC FLAGON SV ROOFING SYNTHETIC MEMBRANES
FLAGON PVC FLAGON SV ROOFING SYNTHETIC MEMBRANES 1085 CPD 0010 1085 CPD 0018 FLAGON SV www.flag.it COMPOSITION Synthetic membrane of plasticised PVC with a layer of glass fibre (50 g/m 2 ) inserted for
More information1993 Specifications CSJ SPECIAL SPECIFICATION ITEM Impermeable Liner
1993 Specifications CSJ 0128-01-085 SPECIAL SPECIFICATION ITEM 5327 Impermeable Liner 1. Description. This Item shall govern for the furnishing and installation of the impermeable liner (geomembrane) shown
More informationLeadax B.V. Covenant K93792/02. Leadax
561/170522 Covenant K93792/02 Uitgegeven 2017-12-01 Vervangt K93792/01 Pagina 1 of 5 VERKLARING VAN KIWA With this Covenant, issued in accordance with the Kiwa Regulations for Product Certification, Kiwa
More informationENRGY CURB APPLICATION GUIDE FOR TPO ROOFING SYSTEMS
1. Introduction The ENRGY Curb mounting system is a lightweight, nonpenetrating, roof-integrated, photovoltaic (PV) mounting system designed to maintain roof integrity and maximize power density. This
More informationCAPPING OF A GOLD MINE IN ROSIA MONTANA, ROMANIA
Rosia Montana has always been rich in mineral resources, especially in gold. Unfortunately the accident at Baia Mare in 2000 brought home to Romanians the dangers of cyanide leaching due to the use of
More informationSAUNA BARREL 3.0 m, Ø Plans: with and without terrace
SAUNA BARREL 3.0 m, Ø 2.27 Plans: with and without terrace SPECIFICATION STANDARD SET Sauna Sauna barrel Length of the barrel, m 3.00 Stainless steel tightening bands Diameter, m 2.27 Roof covered with
More informationHeatExchangerSpares.com Ltd HRS Heat Exchangers Ltd HRS Hevac Ltd HRS Hevac Engineering Ltd HRS International Ltd HRS Investments Ltd
HOT WORKS PROCEDURE 1. PURPOSE 1.1 The purpose of this document is to ensure the safe operation of hot work equipment in accordance with the requirements set forth in 29 CFR 1910 Subpart Q - Welding, Cutting
More informationDrop-In Specifications INTEGRATED DRAINAGE SYSTEM GEOMEMBRANE
Drop-In Specifications INTEGRATED DRAINAGE SYSTEM GEOMEMBRANE The following specification is a sample guideline to be customized by the engineer for preparing site specific specification. This information
More informationMATERIAL SAFETY DATA SHEET FOR MOISTUREGUARD FOR CCA. 1.0 Introduction NZS 5433:1999.
Page 1 of 5 1.0 Introduction Statement of Hazardous Nature: Company Details: Company: Street Address: Postal Address: Telephone No: (09) 277-7770 Emergency Telephone No: 0800 200 162 Not classified as
More informationClean! Clean working by Qdel. Qdel laminating supplies Hamburgstraat 9 NL-7575 EG Oldenzaal T: E: I :
Clean! 2014/06 Content Word of advice 3 1. Gloves 4 1a. Latex 4 1b. Nylon 5 2. Clothing 6 2a. Anti static dust coat 6 2b. Hairnet 7 3. Tools 8 3a. Polish cleaning cloth 8 3b. Dust free roller 9 3c. Paper
More informationSLS Etch Primer. 300g aerosol, 250ml tin, 500ml tin, 1L tin, 4L tin
Overview White Knight Rust Guard SLS Etch Primer is an etching primer with superior locking system for maximum rust protection. Ideal for priming aluminium, galvanised iron ZINCALUME, chrome, brass and
More informationHG-2000E HEAT GUN WATTS
HG-2000E HEAT GUN 2.000 WATTS EN - INSTRUCTIONS Carefully read the instructions for use before you start using the machine. drivenbycare www.orfit.com 1 2 6 8 7 2 8 450 C 300 C 6 A E FE 550 C PVC (hard)
More informationREHABILITATION OF SAIDA DUMPSITE
Traditionally a landfill s construction involves large quantities of natural materials such as clay (waterproofing), gravel (drainage) and sand (filter and separation). These materials are scarce in the
More informationEuropean Technical Assessment ETA-14/0176
British Board of Agrément Bucknalls Lane Watford Herts WD25 9BA Tel: + 44 (0) 1923 665300 Fax: + 44 (0) 1923 665301 e-mail: mail@bba.star.co.uk website: www.bbacerts.co.uk Designated according to Article
More informationPIPE MANUFACTURING CO.
PIPE MANUFACTURING CO. PRE- INSULATED BONDEND PIPES and FITTINGS from -200 C to +315 C; District Heating and Cooling Systems Cogeneration Systems Transport of Steam Systems (aboveground and underground)
More informationDisposal Manual. m{zd{ 6. Capacitor( -ELOOP ) October 2012 Mazda Motor Corporation
Capacitor( -ELOOP ) Disposal Manual m{zd{ 6 Vehicle type in VIN : JM* GJ ****** 100001~ JM* GL ****** 100001~ RUM GJ ****** 100001~ October 2012 Mazda Motor Corporation 1 Capacitor disposal manual_gj_eng161128.xlsx
More informationRoofing Adhesive SARNACOL 2172 Spray
Roofing Adhesive SARNACOL 2172 Spray Spray Applied Adhesive for Sarnafil G and Sarnafil G Felt roof waterproofing membranes PRODUCT DESCRIPTION TESTS PRODUCT DATA FORM Multi Purpose moisture curing PU
More informationFirestone GeoGard EPDM Review of Technical Performances
Firestone GeoGard EPDM Review of Technical Performances 1 Introduction This document presents a summary of the characteristics of the Firestone GeoGard EPDM membrane produced by Firestone Building Products,
More informationFirestone EPDM Geomembrane Review of technical performances
Firestone EPDM Geomembrane Review of technical performances www.firestonebpe.com Introduction This document presents a summary of the characteristics of Firestone EPDM Geomembrane produced by Firestone
More informationTable of contents. Introduction Design. 2. Installation. Attachments
Table of contents Introduction... 2 1. Design 1.1 Field of application...3 1.2 Geomembrane selection...3 1.3 Site selection...3 1.3.1 Nature of the soil...3 1.3.2 Groundwater level...4 1.4 Site geometry...5
More informationCONTINUOUS GEOMEMBRANES FOR ON SITE APPLICATION. PDA Europe 2012 Annual Conference Istanbul, November
POLYMERIC GEOMEMBRANES ARE MADE OF: - POLYOLEOFINS (HDPE, LDPE, LLDPE, TPO, VLDPE). - EPDM. - PVC LIMITATIONS OF CONVENTIONAL POLYMERIC GEOMEMBRANES: - REQUIRE WELDING AT JOINTS AND SEAMS (heat or ultrasound).
More informationPot Belly Black. Overview. Suitable Surfaces
Overview White Knight Pot Belly Black is a heat resistant, self priming paint designed for use on metal surfaces which are subject to radiant heat. Ideal for use on pot belly stoves, heaters, ovens, BBQ
More informationTHE GOOD GUIDE TO BUTT FUSION JOINTING....Connect
THE GOOD GUIDE TO BUTT FUSION JOINTING...Connect THE GOOD GUIDE TO BUTT FUSION JOINTING This guide will provide basic information to enable the operative to: Equipment required: Understand the equipment
More informationSection Specification for Geotextile Used in Permanent Erosion Control Application
Project Name: Project Number: 1 GENERAL Section 02370 Specification for Geotextile Used in Permanent Erosion Control Application 1.1 SECTION INCLUDES A. Geotextile to prevent soil loss resulting in excessive
More informationDehydrator. This construction will dehydrate fruits and vegetables, helping preserve them and concentrating their flavour.
Dehydrator This construction will dehydrate fruits and vegetables, helping preserve them and concentrating their flavour. What you will need A kitchen floor cabinet A good quantity of empty drink cans
More informationMAKE CLEANING SAFER NEW TECHNOMELT. Your Machine Cleaning Guide & Hotmelt Cleaner Range
MAKE CLEANING SAFER NEW TECHNOMELT Your Machine Cleaning Guide & Hotmelt Cleaner Range 2 TECHNOMELT Your Machine Cleaning Guide & Hotmelt Cleaner Range Do you know the advantages of regular and thorough
More informationTextile quality management. Mr Dale Carroll CSIRO, Textile and Fibre Technology
Textile quality management Mr Dale Carroll CSIRO, Textile and Fibre Technology Textile testing Why do you need to test? What does testing involve? Sampling. Selecting the correct test. Selecting the most
More informationROOFING TECHNICAL BULLETIN #07-12
Sika Sarnafil World Class Roofing and Waterproofing ROOFING TECHNICAL BULLETIN #07-12 To: Authorized Roofing Applicators Sika Sarnafil Sales Staff & Sales Representatives Sika Sarnafil Regional Technical
More informationFacility Safety Rules Hazard Communication Emergency Procedures Fire Safety. Safety Orientation
Facility Safety Rules Hazard Communication Emergency Procedures Fire Safety Safety Orientation Facility Safety Rules Report all hazards, unsafe acts, unsafe conditions and unsafe equipment to your Supervisor
More informationPizza Oven with Stand
Pizza Oven with Stand Cooks up to 3 pizzas at a time Use to cook a variety of food Easy clean vitreous enamel interior Model No. P0104 Powerful 22MJ/h stainless steel burner Viewing window and temperature
More informationHave a Question? Call toll-free: Owners Manual L WARNING. Project Series Paint Sprayers Important Safety Instructions
Owners Manual 333394L EN Project Series Paint Sprayers Important Safety Instructions Read all warnings and instructions in this manual and on the unit, including the power cord. Be familiar with the controls
More informationSpectraSeal 2.1 VOC Color Primer Sealer
PRODUCT DESCRIPTION SpectraSeal is a premium quality 2K-urethane primer sealer that utilizes state of the art Ure-Flex TM Technology to provide the ultimate in performance, versatility, and productivity.
More informationINSTALLATION GUIDELINES FOR GEOTEXTILES USED IN FILTRATION AND DRAINAGE APPLICATIONS
INSTALLATION GUIDELINES FOR GEOTEXTILES USED IN FILTRATION AND DRAINAGE APPLICATIONS Prepared by TenCate Geosynthetics North America 365 South Holland Drive Pendergrass, GA 30567 Tel: (706) 693-2226 Fax:
More informationGEOMEMBRANE FIELD INSTALLATION
GEOMEMBRANE FIELD INSTALLATION CONTENTS Introduction Quality Control and Quality Assurance Types of lining systems Basic Lining Design Executive Lining Design Basic Lining Design Specification Executive
More informationSpectraPrime Color Primer Surfacer
PRODUCT DESCRIPTION SpectraPrime is a premium quality 2K-urethane primer-surfacer that utilizes state of the art Ure-Flex TM Technology to provide the ultimate in performance, versatility, and productivity.
More informationFIRST-CLASS IN TRAINS
FIRST-CLASS IN TRAINS Powered by TCPDF (www.tcpdf.org) Powered by TCPDF (www.tcpdf.org) Advanced fire protection for railway vehicles: hazard level 2 & 3 according to EN 45545 Effectively prevents moisture
More informationSYSTEM DATA SHEET Sikafloor MultiDur ES-44 ESD
SYSTEM DATA SHEET SMOOTH, UNICOLOUR EPOXY FLOOR COVERING WITH POLYURETH- ANE ESD ROLLER COATING PRODUCT DESCRIPTION The system is a seamless, smooth, low VOC, ESD epoxy floor covering. It consist out of
More informationLS-JRE OPERATION & INSTRUCTION MANUAL
SOLVENT RECYCLING SYSTEM LS-JRE OPERATION & INSTRUCTION MANUAL Now with adjustable temperature control! TABLE OF CONTENTS Description Page Introduction 1 Safety Precautions 1 Installation / Set-up 1 Supplied
More informationMaterial Safety Data Sheet. acc. to ISO/DIS Printing date 01/26/2001 Reviewed on 03/28/2000
Page 1/7 1 Identification of substance Product details Product code: 0000200644 Manufacturer/Supplier: SEYMOUR OF SYCAMORE 917 Crosby Avenue Sycamore, IL 60178 +1 815-895-9101 Information department: Health
More informationInstallation Guide Maibec Regular Siding
Installation Guide Maibec Regular Siding (with visible nails) Read this entire guide before installing your siding. For proper installation, you must understand and follow all requirements and steps correctly.
More informationJoint Stock Company Alzida Savanorių pr. 221, LT Vilnius, Lithuania
page 1 (13) Joint Stock Company Alzida Savanorių pr. 221, LT- 02300 Vilnius, Lithuania SCOPE OF ACCREDITATION (flexible) No. Name of the testing object Name of the parameters (characteristics) to be tested
More informationFRONT BUMPER COVER - VIN RANGE: H18680->H99999 (G )
PUBLISHED: 11-MAY-2011 2003.50 XJ RANGE (X350), 501-19 BUMPERS FRONT BUMPER COVER - VIN RANGE: H18680->H99999 (G1003267) REMOVAL AND INSTALLATION 76.22.78 FRONT BUMPER COVER - RENEW ALL DERIVATIVES 1.60
More informationHOT AIR GUN MODEL NO: CHG1500D USER INSTRUCTIONS PART NO: GC0414
HOT AIR GUN MODEL NO: CHG1500D PART NO: 3400757 USER INSTRUCTIONS GC0414 INTRODUCTION Thank you for purchasing this CLARKE Hot Air Gun. Before attempting to use this product, please read this manual thoroughly
More informationStormwater protection
70 70 Visqueen High Performance Urban Drainage Geomembrane 70 Visqueen GX Geomembrane UDG 73 Hanson Aquaflow SC Membrane Stormwater protection A fully integrated stormwater management system provides relief
More information43 May cause sensitisation by skin contact. 67 Vapours may cause drowsiness and dizziness.
1.) Identification of the substance/preparation and of the company/undertaking Identification of the substance or preparation Trade name White Marker Use of the substance/preparation Ink for stationery
More informationEMERGENCY PHONE: or (651) (24 hours)
Material Safety Data Sheet Copyright, 2012, 3M Company All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1)
More informationLiner Construction & Testing Guidance Overview
Liner Construction & Testing Guidance Overview Ruben Meza, Jr., P.E. Waste Permits Division Municipal Solid Waste Permits Section 2017: TCEQ Environmental Trade Fair Agenda Summary of Revised Guidance
More informationMAKE CLEANING SAFER NEW TECHNOMELT. Your Machine Cleaning Guide & Hotmelt Cleaner Range
MAKE CLEANING SAFER NEW TECHNOMELT Your Machine Cleaning Guide & Hotmelt Cleaner Range 2 TECHNOMELT Your Machine Cleaning Guide & Hotmelt Cleaner Range Do you know the advantages of regular and thorough
More informationD.P.E. Enviroliner. geotextile protection layer. covering new ground 2016
LEVEL 7 osynthetic clay liner www.gundle.co.za H.D.P.E. Enviroliner geosynthetic clay liner geotextile protection layer D.P.E. Enviroliner solid waste sand (leachate collection) geotextile protection layer
More informationPME. Series Enclosures. Battery Enclosure (BE) Field Upgrade Installation Instructions. Effective: January, Alpha Technologies
PME Series Enclosures Battery Enclosure (BE) Field Upgrade Installation Instructions Effective: January, 2004 Alpha Technologies Power Alpha Technologies. Protecting The Power in Communications. Preface
More informationARCHITECT S SPECIFICATIONS
1 TYPE II PVC-FREE WALLCOVERINGS 1. GENERAL 1.1 Summary Contractor shall furnish, install and finish environmentally friendly wallcovering as specified in the contract documents. 1.2 Sample Contractor
More informationSECTION (15820) - AIR DUCT ACCESSORIES
PART 1 GENERAL 1.01 SUMMARY A. Section includes: SECTION 23 33 00 (15820) - AIR DUCT ACCESSORIES 1. Manual-Volume Dampers 2. Fire Dampers 3. Turning Vanes 4. Duct-Mounted Access Doors 5. Flexible Connectors
More informationGeomembranes that work
Geomembranes that work www.firestonebpe.com Dependable performance in demanding environments Firestone EPDM Geomembrane is a rubber liner offering a flexible and durable solution for a wide variety of
More informationFirestone Lining Systems. Dependable Performance in Demanding Environments
Firestone Lining Systems Dependable Performance in Demanding Environments Firestone EPDM Geomembrane Product Line Thickness Standard Widths Standard Lengths Weight Standard panel sizes 1,02 mm (.040 )
More informationSafety Data Sheet. according to Regulation (EC) No 1907/2006 WICKES SMOOTH MASONRY
Page 1 of 6 SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Further trade names W709356002 WICKES Smooth Masonry Brill White 5,000L W709358002
More informationSafety Data Sheet. according to Regulation (EC) No 1907/2006. SECTION 1: Identification of the substance/mixture and of the company/undertaking
Page 1 of 6 SECTION 1: Identification of the substance/mixture and of the company/undertaking 1.1. Product identifier Further trade names W709353438 WICKES Textured Masonry Barley 5,000L W709355548 WICKES
More informationUrban Drainage Geomembrane (UDG)
Page 1 Impervious membrane for underground stormwater storage systems Also suitable for permeable paving systems Restricts water entering the sub-grade Preserves sub-grade structural integrity Manufactured
More informationUp on the Roof Fire Prevention BY David Laks, P. Eng., CFPS, ARM, RRC
Up on the Roof Fire Prevention BY David Laks, P. Eng., CFPS, ARM, RRC Every year there are a significant number of roof fires resulting from installation, neglected maintenance, or housekeeping. This article
More informationARCHITECT S SPECIFICATIONS For Commercial Vinyl Wallcoverings
1 1. GENERAL 1.1 Summary Contractor shall furnish, install and finish a vinyl wallcovering as specified in the contract documents. 1.2 Sample Contractor shall submit for the architect s approval a sample
More informationVisqueen Vapour Control Tapes
Technical Product Datasheet Edition: 12/01/2018 Identification no. VBP014 Visqueen Vapour Control Tapes Supports the installation of Visqueen Vapour Check membrane Utilises Visqueen s advanced adhesive
More informationCarbon Film Installation Instructions
Contents Page 2 Page 3 Page 4 Page 5 Page 8 Product Overview Pre-Installation & Electrical Provision Depron Underlay Installation Carbon Film Installation - Under Wood/Laminate Flooring Notes & Trouble
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK Bucknalls Lane Garston Watford Hertfordshire WD25 9BA Contact: Alvaro Enquita-Gonzalez Tel: +44 (0)1923-665350 Fax: +44 (0)1923-665452 E-Mail:
More informationSELF-ADHESIVE FILM INSTALLATION GUIDE
SELF-ADHESIVE FILM INSTALLATION GUIDE Table of Contents Important Information... 2 Tools & Materials Required... 3 Installation Procedure... 5 Part 1: Preparing the Smart FILM... 5 Part 2: Clean the Glass
More informationGeomembranes that work
Geomembranes that work www.firestonebpe.com Dependable performance in demanding environments Firestone EPDM Geomembrane is a rubber liner offering a flexible and durable solution for a wide variety of
More informationMARATHON HEATER. File # E Made in USA
MARATHON HEATER S I L I C O N E R U B B E R H E A T E R S File # E202904 Made in USA Wire wound Silicone Rubber Heaters Marathon Heater flexible heaters provide outstanding performance in applications
More informationSchedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK
2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK Presley House Presley Way Crownhill Milton Keynes MK8 0ES United Kingdom Contact: Jeremy Hodge Tel: +44 (0) 1908 267300 Fax: +44 (0) 1908
More informationINSET LIVE FUEL EFFECT GAS FIRE
600B741/02 OWNER S GUIDE MODEL BR650 VA (GC No. 32-032-39) INSET LIVE FUEL EFFECT GAS FIRE THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20) WHEN CONVERTED USING CONVERSION KIT NO.591149 THIS APPLIANCE
More informationCorr/Guard PRESSURE RATED VENTING SYSTEM IMPORTANT: DO NOT INSTALL WITHOUT FIRST READING THESE INSTRUCTIONS VERY CAREFULLY.
CORR/GUARD INSTALLATION INSTRUCTIONS This symbol on the nameplate means this product is listed by Underwriters Laboratories Inc. Tested to UL1738 / CAN / ULCS636-1995 Listing No. MH26687 Testing No. 11EN
More informationPOLICY STATEMENT: Policy Number: Section 600 Physical Plant. Date Adopted: May 7, Date(s) Revised: September 4, 2012
Policy Number: 600.8 Policy Title: Subject: Hot Work Program Section 600 Physical Plant Date Adopted: May 7, 2009 Date(s) Revised: September 4, 2012 Approved by: Daniel J. Bingham Dean/CEO Helena College
More informationOPERATING AND SAFETY INSTRUCTIONS
IMPORTANT NOTE: Please Read These Operating and Safety Instructions Before Using the BoltBuster OPERATING AND SAFETY INSTRUCTIONS Simple instructions to Get Started with Bolt Buster TM Make sure BoltBuster
More informationGASEOUS HYDROGEN SYSTEMS
CHAPTER 7 GASEOUS HYDROGEN SYSTEMS SECTION 701 GENERAL 701.1 Scope. The installation of gaseous hydrogen systems shall comply with this chapter and Chapters 30 and 35 of the Fire Compressed gases shall
More informationBlue Tuna Docs A Paper Plane Project Auditing of Composite and Metal Bonding Facilities. Part 1 Facility Control.
Auditing of Composite and Metal Bonding Facilities Part 1 Facility Control Course Outline Introduction Facility Control Material Control and Testing PAA (Phosphoric Acid Anodizing) Bonding Procedures and
More informationDesign Options Analysis on a Heat Wrap used on PVC Pipe Connections in Cold Weather Conditions
Design Options Analysis on a Heat Wrap used on PVC Pipe Connections in Cold Weather Conditions Bruce W. Smith, CPC and Clint W. Carroll, MS Auburn University Auburn, Alabama Cold weather conditions produce
More informationAnnex of the certificate (Page 1/5) Accreditation Scope
Annex of the certificate (Page 1/5) Accreditation Scope As a Testing Laboratory Tested Materials / Products EX LABORATORY Metallic materials Construction products Address: Küçük Çiğli Mh. 8780/1 Sk. No:5
More informationChapter 18 Welding Table of Contents
Chapter 18 Welding Table of Contents 18.1 Foreword 18.2 Introduction 18.3 Applicability of Standard 18.4 Other Policies that Might Apply 18.5 Approved Areas for Welding and Cutting 18.6 Other Areas 18.7
More informationMaterial Safety Data Sheet
Material Safety Data Sheet Section I. Product Identification and Uses Product Name CARPET SPOTTER Synonyms Chemical Name Chemical Formula Chemical mixture. CI# DSL CAS # Code 1834-19-153 Chemical Family
More informationTABLE OF CONTENTS. SI No Contents Page No.
TABLE OF CONTENTS SI No Contents Page No. 1 Basic wet Processing Terms 2 2 Sequence of operations in Wet processing 3 3 Brief Note on Stenter machine 4 4 Details of stenter machine 4 5 Operating stenter
More information489G DESCRIPTION CAST IRON UNITS BRONZE UNITS 316 STAINLESS STEEL UNITS. Maintenance. General Safety Information for 12 Volt DC Power
Please read and save this Repair Parts Manual. Read this manual and the General Operating Instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect
More informationTOYOTA SIENNA MY LOWER DOOR MOLDING Preparation
Preparation Part Number: PT29A-0800 (Bright Chrome Finish) Kit Contents LH Front Door Molding 2 LH Rear Door Molding 3 RH Front Door Molding 4 RH Rear Door Molding Hardware Bag Contents Recommended Sequence
More informationELECTRIC HEATING THERMOSYSTEM
ELECTRIC RADIANT MAT 8200E INSTALLATION AND USE MANUAL heating passion ELECTRIC HEATING THERMOSYSTEM WARNING: For the guarantee to be valid, the product must be installed and handled as indicated in this
More informationTOYOTA SIENNA MY LOWER DOOR MOLDING Preparation
Preparation Part Number: NOTE: Part number of this accessory may not be PT9A-0800 (Bright Chrome Finish) the same as the part number shown. PT9A-080 (Semi Chrome Finish) Kit Contents LH Front Door Molding
More informationowner s manual produitsneptune.com Do not discard. Save these instructions for further use.
owner s manual AMAZE Installation OPERATION MAINTENANCE Bathtub REPAIR ONE-PIECE freestanding Bathtub INSTALLATION produitsneptune.com Do not discard. Save these instructions for further use. Table of
More informationProduct Information Motor and machine protection
- Basic information The REISSMANN Sensortechnik heater bands were specifically designed for the electric motor industry. These heater bands are delivered as a finished product, in various combinations,
More informationINDUSTRIAL - SOLVENT PARTS CLEANER CM200 (115V OR 230V PUMP)
INDUSTRIAL - SOLVENT PARTS CLEANER OPERATION & INSTRUCTION MANUAL I. Introduction A. Manufacturer s Statement CM200 (115V OR 230V PUMP) This manual will provide you with important information about the
More informationAutomatic Water System Pump SERIES
Automatic Water System Pump 42755 SERIES Automatic Water System Pump Purpose of this manual The purpose of this manual is to provide necessary information for product installation, operation and maintenance.
More informationCivil engineering Fibertex Geotextiles
C O N S T R U C T I O N 100.06 Civil engineering C O N S T R Constructing with Fibertex offers a full range of nonwoven geotextiles designed for use in many different foundation structures within civil
More informationPRODUCT SAFETY DATA SHEET
PRODUCT SAFETY DATA SHEET Print date: 14 26 Sep Oct 2006 2009 1. PRODUCT AND COMPANYIDENTIFICATION Item Number / Product name: d-con FLAT GLUE TRAP Validation / Revision Date: 14 26 September October 2006
More informationIndustrial - Remote Reservoir Parts Cleaner Operator's Manual. Read and understand all labels, MSDS, and this instruction manual before use.
I. Introduction A. General Information Read and understand all labels, MSDS, and this instruction manual before use. The Industrial - Remote Reservoir Parts Cleaner is an economical, safe, and innovative
More informationSMALL DIAMETER CORR/GUARD & SLEEVED CORR/GUARD
CORR/GUARD INSTALLATION INSTRUCTIONS This symbol on the nameplate means this product is listed by Underwriters Laboratories Inc. Tested to UL1738 / CAN / ULCS636-08 Listing No. MH26687 Testing No. 11EN
More informationINSTALLATION GUIDE AND CHECKLIST
INSTALLATION GUIDE AND CHECKLIST CLOCK SPRING SNAP WRAP November 2017 Copyright Clock Spring Company, L.C. TABLE OF CONTENTS a Snap Wrap Information...i Inspection Checklist...iii Snap Wrap Contents...1
More informationCHAPTER 8 OCCUPATIONAL HEALTH AND SAFETY
CHAPTER 8 OCCUPATIONAL HEALTH AND SAFETY 8.1 Health and Safety Aspects Plant operation will involve storage handling and use of fuels and several chemicals. Some of these chemicals may be hazardous in
More informationPatio Heater Model No. GM and GM
Patio Heater Model No. GM124-003 and GM124-004 FEATURES: The ideal solution for extending the season for outdoor entertaining Maximum output 39.6 MJ/hr Direct ignition Adjustable heat output Safety tip-over
More informationRhepanol hg. For more information on SIG Design & Technology visit A solid foundation for green roofs.
A solid foundation for green roofs. Roofing membranes Rhepanol hg He who sows on Rhepanol hg, will reap enormous benefits. The youngest offspring of a leading roofing membrane system: Rhepanol hg Actually,
More informationMaterial Safety Data Sheet Masonite TM Hardboard
MSDS: Masonite TM Hardboard Page 1 of 5 Material Safety Data Sheet Masonite TM Hardboard Product Name SECTION 1 IDENTIFICATION OF THE MATERIAL AND SUPPLIER Masonite Hardboard Other Names Masonite Pegboard
More informationOWNER S MANUAL WISTERIA
OWNER S MANUAL WISTERIA INSTALLATION OPERATION MAINTENANCE BATHTUB REPAIR ONE-PIECE FREESTANDING BATHTUB INSTALLATION alcove.ca Do not discard. Save these instructions for further use. Table of Content
More informationRevision date: 22/4/2016 Date of print: 11/5/2016 Version: 1 Language: en-ca,us Page: 1 of 8
Version: 1 Language: en-ca,us Page: 1 of 8 Product identifier Trade name: 1. Product and company identification Relevant identified uses of the substance or mixture and uses advised against General use:
More informationINSTALLATION & MAINTENANCE MANUAL FOR FLUE RENOVATION SYSTEM HT1000
INSTALLATION & MAINTENANCE MANUAL FOR FLUE RENOVATION SYSTEM HT1000 Edition Revision Approved by Written by 1 1.2 C. Lezzi C. Lezzi Date 14/02/2011 Page 13 Code 01_01 Manuale_inst_-HT1000 File Name 01_01.2_Manuale
More information