Hardwire & Wireless Control Panels With Incorporated Automatic Telephone Diallers

Transcription

1

2 Hardwire & Wireless Control Panels With Incorporated Automatic Telephone Diallers DUALCOM 8 (GSM/PSTN) ABS MET Control panel with on-board dual network dialler (PSTN and GSM) and Ademco 4+2 and Contact ID transmission software for control monitoring station (CMS). 8 hardwire and 48 wireless zones compatable with the Pegaso transmission protocol. Possibilità to expand with pcb. EZ-8 an additonal 24 hardwire zones. 3 indipendent hardwire inputs for Fire, Hold-up and Panic triggers. Panel is fty. supplied with 8 hardwired, 48 wireless zones and keypad KP-8R with on-board transceiver. Managment and programming of the control panel may be done through keypad or P.C. Management of up to 8 kaypads through 3 wire BUS. Indipendent management of 2 AREAs, with DAY, NIGHT and BYPASS funtions on each AREA protected. Management of 8 operators on 6 levels of security. ARMING/DISARMING of panel through KP-8 keypad (supplied), or PEG 3 keychain transmitter and SK-8 electronic key (optional), o chiavi elettroniche SK8 (see pages 6 & 8). Siren outputs, BUS input for remote electroic key receptical SK-8B. BUS output for HOME AUTOMATION function (HA-3) with remote activation through the on-board dialler. Event memory for (arm/disarm, alarm triggers and panel faults) with SMS and voice transmission of all information collected. Digital event transmission to CMS receive station. Working frequency: Mhz., A.C. power: 230 V. D.C. power 2 amp. 12 V. Battery compartment: Max. 7AH. DUALCOM Same as DUALCOM 8 but with 16 hardwire zones. Available with metal housing only. Wireless and Hardwire Panels VISION 8 FR ABS MET zone hardwire and wireless control panel. 1 hardwired and 2 wireless sensors may be connected to each zone. Microprocessor controller. Tamper protection for removal from wall and opening. Wall mounted. Robust ABS or STEEL housing. Self learning of all sensors and keychain transmitters. Arm and disarmed with PEG-3 keychain transmitter supplied. Remote arming through hardwired electronic key (optional) or with hardwired keypad with display Digit KD (optional). Arming in Test-control mode ( Chime function ). Every zone maybe configured as immediate, delayed, day, night, normally closed (NC) or with double balance lines. Alarm priority. Alarm recyclable and non recyclable with separate relay trigger outputs (Imax 8Amp.) Automatic by-pass of defective zones. By-pass of all zones. Terminal output to signal armed or disarmed. Alarm memory. Siren terminal output. Terminal output for automatic telephone dialler (output for low battery and tampering of sensors). Power 230 Vca/ 50/60 Hz; working frequency Mhz. SMD technology. Backup battery for ABS housing 12Vcc - 7,5 Ah max. (backup battery for steel housing, 7,5 or 17 Ah max.) Dim. ABS housing: 275x220x80mm. W.: 1.4 Kg. Dim. Steel housing: 310x315x80mm. W.: 6 Kg. VISION 24 FR Same characteristics as the VISION-8 FR, but with 24 zones hardwired/wireless and 16 only wireless (total 40 zones). Available only in the steel housing. Dimensions: 310x315x80mm. VISION 40 FR ABS MET Same characteristics as the VISION 8FR, but with 8 zone hardwired/wireless and 32 zones only wireless (total 40 zones). Available in ABS or steel housing. Page 2

3 DualCom Panel Accessories KP-8 R Keypad supplied with the control panels series DUALCOM for unit programming and total or partial arm/disarm with 3 wire bus connection. Onboard custom built tranceiver for the management of the wireless installations and in addition: Alfanumerical LCD display 16x2 characters, Zone by-pass function, Alarm trigger memory, Keypad illumination, Beep confirmation of keys pressed, Technology SMD., Elegant and robust ABS housing. Dimensions: 165x100x30 mm. Weight: 250 gr. KP Same characteristics as the KP-8 but without onboard custom built transceiver. EZ Eight zone hardwire expansion module for Dualcom control panel. Maximum 2 for each mother board. HA Home Automation module for the Dualcom control panel. On-board (3) 10amp. Dry contact relays. VP-7NT Wireless Control Panels Telelink Series Compact wireless standalone alarm system. Ideal for the protection of Homes, Stores, Boats, Campers, etc. against burglary, fire, gas, hold-up or medical distress. Incorporates: an infrared sensor (coverage 12 meters), a powerful piezoelectric siren (118 db/m) a rechargeable bat. (12 V ma). Characteristics: 42 zones memorized wireless zones ( 40 for burglary, fire & holdup)(1 for incorporated infrared), (1 for hold-up) and in addition one hardwired zone. Each zone maybe programmed as: Immediate, Delayed, Day, Night, Burglary, Fire or Gas. Self learning of the codes transmitted from all wireless (sensors, sirens, keypads & keychain transmitters) that function with the Pegaso protocol. Arming and disarming with PEG-3 keychain transmitter (supplied). With PEG-3 you may (Arm/disarm, partially arm, alarm memory & panic activation). Microprocessor controlled. Optical/acoustic R.F. transmission test. Acoustic signalling of unit armed or disarmed (excludible). Siren incorporated with 3 different sounds, 1 for burglary, 1 for fire and 1 for hold-up which maybe excluded. Possibility to program alarm time. Alarm cycle counter (excludible). R.F. outputs for wireless siren and telephone dialler. Supplied with D.C. power supply 230 Vac -> 14 Vdc. Working frequency 433,92 Mhz. Dry contact relay output. Negative output for status of the installation and alarm memory. Additional 12 Vdc. Output. SMD technology. ABS housing. Dimensions: 105x35x190 mm. Weight: 1 Kg. PATENT Nr VP-6XS The VP-6XS has the same characteristics as the Telelink VP-7NT, but does not have built-in the infrared sensor or back-up battery which is optional. Additional characteristics: Electro dynamic siren driver (120 db at 3 meters), terminal output for burglary, hold-up and fire alarms, terminal output for mains failure and low battery, Terminal output for remote key, 2 hardwire terminal outputs ( N.C). Rechargeable battery compartment for 12 V 7 Ah max. (not supplied) Dimensions: 275x220x80 mm. Weight: 1.1 Kg. VP-6N KIT Kit DO IT YOURSELF. Totally wireless and factory programmed: 1 VP-6N, 2 infrared sensors IR-120VRP 1 magnetic contact MG-1P,1 power supply 230 Vca -> 14 Vdc 2 keychain transmitters PEG-3 Installation manual and parts necessary. Same characteristic of the VP-7NT, but does not incorporate an infrared sensor and the built-in siren is electro dynamic. Minimum order 100 pcs. Page 3

4 Indoor Wireless Sensors IR-120 VRP Wireless infrared sensor with special Fresnel lens having 102 facets on 6 levels and a range of 15 meters. Microprocessor controlled with Pegaso transmission protocol. Tamper protected. Working Frequency: Mhz. Wall mounted or with incorporated swivel. Powered by a 3V 1,5Ah long life lithium battery: CR-123. R.F. range 100 meters in open space. Dimensions: 60x110x50mm. Weight: 100g DT-280 VRP Wireless double technology sensor which combines both infrared and microwave technology in a single sensor. Pegaso transmission code self learned by the control panel. Coverage 15 meters With special lens,102 facets on 6 levels. R.F. transmission range 100 mt in open space. Tamper protected. Powered by long life Latium battery 3V 1,5Ah (CR-123) incorporated.. Regulation of range of infrared and sensitivity of the microwave. Swivel incorporated. Dimensions: 60x110x50mm. Weight 120 g. TR-448 VR Wireless curtain lens passive infrared sensor, ideal for the protection of doors and windows. R.F. range 100 mt. In open space. Infrared regulation and discrimination of animals with weight of less then 20 Kgs. Powered by 2 batteries 3V 1,5Ah included. Dimensions: 90x50x40 mm. Weight: 60 g. GA-15VR Wireless gas detector with incorporated siren (85db/m) sensitive to the most common gases as metano, GPL, natural gas etc. Optical measurement of gas level from 1 to 10. Microprocessor controlled. Working Temperature: from 10 to +50. powered directly from the mains 230Vac. And installed directly to A.C. outlet. Working frequency 433,9 Mhz. ABS housing. Dimensions: 120x68x68 mm. Weight: 135 g MG-1P Wireless magnetic contact. Microprocessor controlled. Transmission Pegaso protocol self learned by control panel. Working frequency: Mhz. Powered by 12 V battery incorporated. R.F. range100 mt. in open space. Dimensions TX: 55x32x13 mm. - Weight: 50g. Dimension magnet: 58x11x10 mm. Weight: 20g. MG-3P Wireless Pegaso transmitter that may be installed along with any hardwired sensors to allow this sensor also to become wireless and function with a Pegaso wireless control panels. N.C. contact. Working frequency: Mhz. Powered by 12V battery included. R.F. range 100 mt. in open space. Dimensions: 55x32x13mm. Weight: 50g. SM-2P Wireless optical smoke detector sensitive to all types of smoke. Microprocessor controlled. Pegaso transmission protocol self learned by the control panel. Working frequency: Mhz. Built-in sounder (96 db). SMD technology. Powered by 9 V battery included. ABS housing. R.F. range 100 meters in open space. Dimensions: Diameter 125 mm. Height 45 mm. Weight: 150 g. Page 4

5 Indoor Wireless Sensors MG-6 P Magnetic contact with powerful R.F. transmitter. Range in open space 180 meters, which is superior to that of the MG-1P. This contact maybe used in place of the MG-1P if a greater range is necessary. Powered by 9V alkaline battery incorporated with life of about 18 months. It can be used, separately, as a NC contacts transmitter. Dimensions: 127x33x26mm. Weight: 118 gr. MG-8 P Combination magnetic contact and vibration sensor. R.F. range: 150 meters in open space. Onboard connection terminals for any normally closed contact. Input connection terminal for tape switch or inertial sensor. Powered by 3V lithium battery with 36 months life. Dimensions: 115x33x27mm. Weight 78 gr. STC Wireless accessory that allows the end user to see the status of the control panel from remote through the incorporated LED signals. The unit shows if panel (armed or disarmed). Powered by 9 V alkaline battery incorporated with life of about 12 months. Working frequency MHz. Microprocessor controlled. Dimensions: 127x33x26 mm. - Weight 50 g. Outdoor Wireless Sensors 3i-99 VR Intelligent wireless outdoor triple technology sensor for indoor and outdoor use. This sensor Incorporates 2 PIR and one microwave sensor which creates three dimensional protection of outdoor or indoor space. The sensor is water proof and totally protected against atmospheric conditions and incorporates an electronic system of discrimination against alarms triggered by small animals. Microprocessor controlled, and ammine to direct sun light disturbance. Fully tamper protected. Power Vdc., current drain 18 ma, alarm trigger time 2 seconds. Immunity R.F. Working temperature -20 a Maxim um humidity 95%. Microwave frequency Ghz. Pegaso transmission protocol incorporated; working frequency 433,92 Mhz. Combined with the 2 channel receiver RX2C it maybe installed with any hardwire control panel. Dimensions: 215x110x80mm. Weight: 400g. 3i-99 VR Solaris Same characteristics as the 3i-99 VR, but completely wireless. This unit is powered by an incorporated battery which is charged by a solar cell also incorporated on the top of the unit. Current drain 80 ma Dimensions: 300x110x118 mm. Weight: 1.2 Kg. Wireless Receiver RX-2C Two channel radio receiver which is capable of self learning up to 10 different codes. Two volt free relay outputs with on/off or pulse function ( max 1 A). Powered 12Vdc. Frequency Mhz. SMD technology assembly. Dimensions: 76x76x19 mm. Weight: 50 gr. Page 5

6 Wireless Outdoor Sirens TLM-21 VRP Outdoor electromagnetic wireless siren. Powered by 12 V - 1,3 Ah battery and charged by power adaptor 230 Vac -> 12 Vdc incorporated. Power output: 110 db/m. Housed in polycarbonate container with inner steel container creating double protection against tampering. Microprocessor controlled. Protected against. Unauthorized opening and removal from wall. If the siren is triggered it will automatically trigger also the control panel. The siren will advise with optical and caustic signal the status of the control panel. The siren will self learn the code of the control panel with which it is installed. Output transmission for low battery and mains failure. Different alarm sounds for Burglary, fire and hold-up. Supplied with rechargeable 12V 1,3Ah Battery. Working frequency: Mhz. SMD technology. Dimensions: 210x260x95 mm. Weight 1.45 Kg. TLM-7 Solaris TLM-18VRP PEG-3 Standard 280,00 With Anti Foam 320,00 Renewable Energy wireless siren with on board Pegaso transmission protocol and electro dynamic driver horn 120dB/m. Housed in a double protected polycarbonate container with built-in Robust zinc plated metal housing. Full tamper protection from opening of front cover or removal from wall. Totally controlled by microprocessor. Any siren tampering will trigger also control panel alarm. Both acoustic and optical signal of installation status. Self learning of Pegaso transmission code sent to the control panel. Alert sent to control panel if on board battery is low. 3 different alarm trigger sounds: Burglary/Tamper, Fire and Hold-up. Amber low consumption, high luminosity long life LEDs. On board approved R.F. modules. Antifoam protection (Optional). Supplied with rechargeable 12V 1,3Ah Battery. Working frequency: Mhz. Technology SMD. Dimensions: 280x195x95 mm. Weight: 1.45 Kg. TXM-7 45,00 The TXM-7 is a special made transmitter normally used to trigger an indoor or outdoor siren that functions with the PEGASO protocol with an hardwire control panel. In addition it allows the end user to know when the control panel is armed or disarmed by beeps and flashing. Dimension: 55x75x21 mm. Weight 30g. Same characteristic as the TLM-21 VR, but with battery 12 V 0,7 Ah. Housing in ABS. Acoustic output 110 db/m. This siren is for indoor installation. Dimensions: 165x109x51 mm. Weight 650 gr. 3 channel keychain transmitter to Arm & Disarm the control panel in both day and night modes. Partial arming of the system and trigger of hold-up or medical distress alarm. Microprocessor controlled. Self learning code with all wireless control panels: Phoenix-Vision-Telelink-RX- 2C-VP-6XS Frequency: Mhz. Technology SMD. ABS housing. Powered by Alkaline bat. 12V incorporated. Dimensions: 65x34x14 mm. Weight:30 gr. RPS-20 / RPS-1 Wireless Indoor Sirens RPS-20 R.F. signal repeater which allows you to increase the range of all the Pegaso sensors and keychain transmitters. The unit can learn up to 50 different codes that will be retransmitted 20 times to the control panel. Microprocessor controlled. Working frequency Mhz. R.F. range in open space 100 meters. Powered by 9 V alkaline battery incorporated or by optional 12 Vdc. adapter Technology SMD. ABS housing. Dimensions: 110x80x29 mm. Weight: 150 gr. RPS-1 Same characteristics as the RPS-20, but used as repeater for the Pegaso wireless sirens only Wireless Control Panels Accessories Page 6

7 Hardwire Control Panels IT Control panel with 4 zones with by-pass, through built-in dip-switch the installer may choose to have these zones with end of line resistor or just normally closed. Three zones are always active (panic, fire,& hold-up). Arming and disarming by means of a high security 3 position key switch: Key positions DAY NIGHT - OFF. LED signals for zone armed or bypassed. Alarm and memory LEDs. Acoustic and Led signal for low battery. (Imax 5 A) relay output for indoor siren and (Imax 10 A) available for outdoor siren. 2 relay outputs for fire alarm and hold-up (Imax 1 A). Terminal output both acoustic and LED to signal unit status. Possibility to select the alarm time duration, (1, 2, or 3,minutes or continuous). Selection of entrance times (15, 30,60 seconds or immediate) and the exit times(20 or 40 seconds). Rechargeable battery compartment 12 V - 7,5 Ah max. SMD technology. Robust ABS housing. Dimensions: 275x220x80 mm. Weight: 1.3 Kg IT-400 K Same characteristics as the IT-400, but armed and disarmed by means of an electronic key SK-8 on the front of the control panel. The control panel is supplied with 2 keys. Upon request the following receptacles are available (SK-8B /SK-8M /SK-8L). See Page 11 VISION zone control panel of which 8 maybe programmed as: immediate, delay, day, night, normally closed or double balanced with separate trigger outputs for burglary and sabotage alarms. The other 3 zone are always armed and normally installed as Fire, Panic and Medical Distress. Microprocessor controlled. Built-in rugged ABS housing with tamper control of cover and wall removal. Alphanumerical 16 x 2 LCD display. Total of partial arming with electronic key on the front panel. Remote total or partial arming with optional receptacles SK-8B/8M/8L or optional digital keypad DIGIT-KD See Page 11. Panel may be armed for test control (chime mode). Installer may program 8 different keypads or electronic keys with different code. Built-in: Protection against use of false keys; Recyclable and non recyclable alarm trigger relay outputs (Imax 8A); Automatic 4 cycle alarm cut off. By-pass on all 8 burglary alarm zones. Possibility to arm/disarm zones in groups, for day or night arming. Alarm memory on all zones. Low battery output signal. Terminal outputs for sirens with and without battery back-up. Separate output relay terminals for Fire & Panic alarm trigger (Imax. 1A). Programmable entrance and alarm trigger time. Silent or audible pre-alarm during entrance/exit time with built-in buzzer. Dedicated terminal outputs for automatic telephone diallers which signal: Low battery, Sabotage, Fire, Burglary and Hold-up or medical distress alarm triggers. Terminal output to signal control panel status armed/disarmed. 2 amp. Built-in switching power supply. Rechargeable battery compartment 7.5 Ah 12V. Max. SMD Technology. Mains power 230Vac. Dimensions: 275x 220 x 80. Weight: 1.4 Kg. VISION 8 M Same characteristics as VISION 8, but with steel housing with rechargeable battery compartment for up to 12 V - 18 Ah. Dimensions: 310x315x80 mm. Weight: 6 Kg VISION 24 M Same characteristics as the VISION 8, but has zones and expansion module for an additional 16 zones incorporated. Available only in the steel housing which can house a rechargeable battery of up to 12V-18 Ah. Dimensions: 310x315x80 mm. Weight: 6 Kg Page 7

8 Indoor Hardwire Sensors IR Infrared sensor manufactured with SMD technology. High immunity against R.F. interference and RFI - EMI disturbances, special Fresnel lens with 102 facets on 6 levels. Coverage 120 horizontal and 105 vertical. Immune to white light. Wall or Corner mount, or with incorporated swivel bracket. Led walk test. Protection against tampering, Power: 12Vdc., Current drain: 12 ma in standby. Elegant ABS housing. Dimensions 60x110x50 mm. Weight 100 g. DT Microprocessor controlled double technology sensor. This sensor incorporates the technology of Passive infrared and that of Microwave to reduce the possibilities of a false alarm. The sensor also incorporates a special Fresnel lens with 102 zones on 6 levels, range 15 meters, coverage angle 120 horizontal and 105 vertical. Power 12 Vdc. Cu rrent drain with relay active 23 ma. Alarmed memory. Pulse counter with time between pulses, both programmable. Possibility to select the functions method AND or OR or AND/OR. Microwave frequency 10.5 to 10.7 GHz. X band X. High immunity against electromagnetic disturbances. SMD technology. Incorporated swivel bracket. Elegant and robust ABS housing. Dimensions : 60x110x50 mm. Weight: 100 gr. TMW Microwave sensor incorporated in an elegant and robust ABS PIR sensor housing. Incorporated is special microwave module that creates a Doppler effect and has a regulated range of minimum 1 to 15 mt. with protection angle of horizontal 90, vertical 60. Working frequency 5,9 Ghz. Working temperature: from 20 to Wall or corner mount; or with incorporated swivel. Power 12Vdc, standby current drain: 30 ma. Alarm output contact N.C. Immunity to RF. Disturbances. Dimensions: 60x110x50 mm. Weight 100 gr. Until end of inventory. IR-MAGIC Passive infrared sensor to be installed in a normal Magic 230 Vca. Outlet. Range 7 meters with an angle opening of 120. This sensors is powered directly form the outlet power source: 230Va.c. Until end of inventory TK Stand alone passive infrared with sounder incorporated to signal the presence or passage of people. This unit based on how it is programmed will signal the passage of people with a ding dong sound or a 2 tone alarm trigger of 30 second. Powered by 9 V battery incorporated. Current drain when in stand-by: 50 ua. Range: 10 meters. Coverage angle: 130. Dimension: 108x73x35 mm. Weight 100 gr. Page 8

9 Outdoor Hardwire Sensors LIGHT GUARD MS Outdoor infrared sensor light with Fresnel lens with 29 facets. The Light Guard is used to signal the presents of intruders by switching on a halogen 500 watt. Light.. This source of light can be regulated to light up from 10 sec. To 10 min. Infrared range : 15 meters Robust and inelegant ABS housing. Dimensions: 186x280x140 mm. Weight: 914 gr. Until end of inventory. BST Dual electronic beam for indoor and outdoor installation. Made in polycarbonate material with Horizontal optical axis adjustable 180 ( ) and ve rtical axis 20 ( ). Two pulse infrared be ams with adjustable response time. Output alarm trigger relay Rating: AC./DC. 30V 500mA. Recommended protection distance: in-door 300mt. - outdoor 100 mt. Current drain 65mA. Working temperature: -25 to +55. Dimensions: 170x 80 x 75 mm. Weight : 645 gr. BSE Same characteristics as BST-100 but with 3 beams that must be cut simultaneously for alarm trigger. Current drain: 60mA. Dimensions: 110 x 100 x 210mm. Weight: 1.5 Kg. BSH Same characteristics as the BST-100 but with 6 beams indoor range 450 mt and outdoor range 150 mt. With 6 protection beams. Current drain: 100mA. Dimensions: 110x100x350mm. Weight: 2.7 Kg. BSF Indoor/outdoor 4 beam infrared fence for the protection of walls, doors, windows etc. With outdoor range 30 meters. It is a robust and elegant aluminium profile. It has engineered ABS joints which makes this product solid, durable and equipped with tamper protection. The unit is specially designer against damage from sun light, rain proof, moisture poof and easy to install with 360 adjustment. Powered from control panel 12/18 Vdc. Working temperature: - 35 to 55. Dimensions: Height 63 cm. Weight: 680 gr. BSF-830 Same characteristics of the BSF-430 but has 8 beams of protection. Dimensions: Highs 168 cm. and weight is 1.58 kg i Triple technology intelligent sensor for indoor and outdoor installations. The sensor incorporates 2 PIR elements and a microwave detector which allows three dimensional protection of the area in which it is installed. The sensor is built in a robust weather proof housing and has built-in discrimination protection against triggers caused by small animals. Microprocessor controlled, immune to direct sun light. Fully tamper proof. Power: Vdc., Power drain: 24 ma, Alarm trigger time 2 seconds. Immunity R..F. interference. Working temperature -20 to Maximum humidity 95%. Microwave frequency Ghz. Shock and masking sensors incorporated. Dimensions: 215 x 110 x 80mm. Weight: 400 gr. Page 9

10 Hardwire Sirens TLM-13F High power piezo electric siren with battery backup and 2 sounds incluided.(120db/m). ABS housing with polycarbonate outer cover and metal inner cover. TAMPER Protection from opening of front cover and removal from wall. Positive and negative alarm trigger commands. Rechargeable battery incorporated. Supplied with amber flasher, available in blue and red on request. Programmable alarm time: 3 min., 20 min. or continuous. LED for status control. Power: 12 Vdc. Dimensions: 260x50x200 mm. Weight 786 gr. Until end of inventory. TLM- 30 F High power siren with electrodynamics driver (130 db/m). Manufactured with 2 metal protection covers. One in deep pressed aluminium and the other in zinc plated steel. Front cover is painted with epossipolyester RAL 7035 paint which gives greater protection against adverse weather conditions.. Incorporated: electronic flash, special tamper switch which protects the siren from unauthorized cover removal or removal from wall. Possibility to exclude the siren in case a fault develops. Output terminals for: remote flasher; siren trigger disarm; NC. Contact to trigger control panel. Automatic arming of siren 10 second after the last cover has been put into position. Rechargeable battery compartment for max. 12 V - 7,5 Ah. Power 13,8 Vdc. Dimensions: 280x195x85 mm. Weight: 2.2 Kg. ELIMINATOR 12 Standard With Anti Foam Electronic siren with built-in TAMPER against opening of front cover and removal from wall. Robust and elegant policarbonate housing with additional protection by means of a steel zinc plated inner housing. New LED low current consumption & long life flasher. Indication of control panel status (Armed/Disarmed). Normally Closed alarm trigger terminal connection. Terminal output for alarm cut-off in case of emergency. Acustic output 125dB at 1 Meter. 20 second standby period between alarm triggers. Siren activation period of 22 second after having closed the last cover. 3.5 minuite indipendent alarm trigger time. Possibility to change the characteristics of the siren through the onboard jumpers. (Optional) anti foam protection. Battery compartment 12 Vdc Ah max. Power 13.8 Vdc. Current drain in standby: 30 ma. Current drain in alarm: 1.5A. Dimensions: 285 x 222 x 90mm. Weight without battery: 2.8 Kg. TLM 39 High power electronic 2 tone siren with peak of 40 W. Acoustic sound output 130 db/m. ABS housing. Current drain 1,5 A - Weight 700 gr SB Pies electric siren. Acoustic output 105 db/m. Power 12 Vdc. Current drain 100 ma. Weight 100 gr. TLM H Pies electric siren in elegant ABS housing with flasher incorporated. Power 12 Vdc. Current drain 170 ma. Acoustic output 110 db. Colour white and amber flash. Dimensions: 122x74x42 mm. TLM Pies electric siren in elegant ABS housing design. Power 12 Vdc. Current drain 200 ma. Acoustic output 115 db/m. Dimensions 145x109x48 mm. Weight 400 gr. Page 10

11 DualCom, Vision, IT400 Panel Accessories DIGIT - KD (Only for Vision) Hardwired alphanumerical LCD 16x2 character display for remote arming/disarming, total or partial.of series VISION control panels. Arming in Test-Control (Chime mode). By-pass of zones and alarm memory. Arm/disarm codes are self learned by the control panel. Built-in protection against false attempts to arm. Backlight illumination on all keys. Beep buzzer to confirm key pressed. SMD technology. Elegant ABS housing. Dimensions: 165x100x30 mm. Weight: 250 gr. SK - 8B Remote receptacle for electronic key SK-8 with LED indications for: panel armed, panel disarmed, panel partially armed, and alarm memory. Built in nylon fibreglass material and maybe fixed to a surface with nut supplied. Diameter 23 h-30mm. Weight: 10 gr. SK Supplementary electronic key with 4 billion codes which may be self learned by the control panel. SMD technology. ABS housing. Dimensions: 54x20x10 mm. Weight: 10 gr. SK - 8M Same characteristics as the SK-8B but in version MAGIC. Dimensions: 24 x 44 x 30mm. Weight: 20 gr SK - 8L Same characteristics as the SK-8B, but in version LIVING. Dimensions: 24x44x30 mm. Weight: 25 gr. SINTEL 3 VM Automatic PSTN Telephone Diallers Three channel voice dialler with guided menu. Can send the 3 messages to 5 different memorized telephone numbers. Fully controled by microprocessore. On board programming keypad. Guided voice menu for all functions. One relay output with remote cammand through the PSTN tel. line. Password code for End user. Installer password code. Password code for total resent function. Message playback through the guided menu. Total reset from remote or by control panel. Output terminal for inhabition function. Power drain 15mA. Power: from 9 to 24 Volts dc. Dimensions: 110x80x29 mm. Weight: 180 gr. Automatic GSM Telephone Diallers GMTEL Automatic telephone dialler capable of sending 3, 10 second voice and 3, 75 characters SMS messages to 5 different telephone Numbers over the GSM network. Modem 900/1800Mhz incorporated. Microprocessor controlled. 3 alarm trigger channels: Burglary-Fire - Holdup. 1 channel for control panel status. User friendly and fast programming by sending SMS messages to the unit. 3 terminal relay outputs controlled by remote SMS messages for (HOME AUTOMATION). Remote interrogation of relay status by means SMS messages. 8 LED status control of unit: Remote status control of relays, alarm, GSM signal. Power 12 Vdc. SMD technology. Robust and elegant ABS housing. Incorporated back-up battery compartment. Dimensions: 180x112x33 mm. Weight: 240gr. GATEL GSM 900/1800Mhz modem with dry contact relay incorporated. Possibility to memorize up to 499 Different telephone numbers and if any of these numbers call the GATEL-1, the unit will not reply but the only ring will trigger the incorporated dry contact relay. This unit may be used for access control as opening of GATES, DOORS etc. GATEL-1 is programmed with an incorporated wireless keypad. Built in SMD technology. ABS housing. Dimensions: 114x90x35 mm. Weight: 180 gr. Page 11

12 Survelliance System GSM / MMS EG-3 A new generation alarm sensor, telephone dialler, CCTV camera and alarm control system all in a signal compact elegant and robust tamper protected housing. With its ultra modern microprocessor Technology the EG-3, On board Camera, R.F. Receiver, R.F. Transmitter. PIR Sensor, GPRS modem, SD card memory bank will in real time transmit information, images and data to your cellular telephone and your personal computer via MMS and . One device with four installation modes. The EG-3 may be installed as: SL: Stand Alone (armed./disarmed by means of keychain transmitter supplied.) HW: Installed with any hardwire installation (arm/disarmed and power form the control panel) HW: Installed with a TRE i systems wireless control panel with Pegaso protocol (arm/ disarmed by wireless control panel.) SLM: As a wireless control panel which can control up to 20 slave sensors Ideal to be installed in existing hardwire installations. By combining various technologies together, the EG-3 will keep the end user informed on everything that takes place in his home, office etc. On the EG-3, for hardwire installation a normally closed terminal contact is provided and maybe used with any control panel (new or old). Once triggered the unit will transmit to your cell phone and address 5 images of the protected area along with an SMS which indicates the type of alarm trigger (burglary-fire-hold-up). To the 5 memorized telephone numbers the built-in dialler can send one of 3 SMS messages having 80 characters each. Other characteristics: listen-in function, 2 way communication, 2Gb SD memory for over 2000 images (32 images per alarm). Package EG-3 HW/WL EG-3 for hardwire or wireless installation. Incorporated: 2 Amp. power supply, Micro SD card, Battery Back-up, Swivel bracket, GPRS antenna, Mounting screws, Installation manual and garantee. Package EG-3 SL/SLM EG-3 for stand alone and stand alone master installation. Incoporated 2 Amp. power supply, Micro SD 2Gb, Batery Back-up, Swivel bracket, GPRS antenna, Mounting screws, Installation manual, Garantee certificate and 2 PEG-3 keychain transmitter used to arm and disarm the EG-3. EG-3 HW/WL Accessories PEG Single channel water proof kaychain transmitter for use with EG-3 all versions to trigger: Medical destress, Panic or Hold-up alarm. EG-3 SL/SLM Accessories PEG Two channel keychain transmitter for EG-3SL and SLM. Functions: Arm/Disarm unit and trigger Medical Distress, Panic or Hold-up alarms. Page 12

13 Magnetic Contacts ART N.C. magnetic contact in ABS, for installation on wood doors. Dimensions 15 x 30 mm. Weight 25 gr. ART F N.C. magnetic contact in aluminium alloy for installation on metal doors. Dimensions 32 x 15mm. Weight 30 gr ART N.C. with ABS housing for installation on wood doors. Diameter Ø 9.25 mm. Weight 25 gr ART N.C. magnetic contact made in brass for installation on metal doors. Diameter Ø 7 mm. Weight 30 gr. ART N.C. magnetic contact for folding garage doors made in aluminium alloy. Dimensions 105 x 38mm. Weight 400 gr. ART N.C: magnetic contact for installation on large metal doors. Dimensions. 20 x 50mm. Weight 150 gr. ART N.C. magnetic contact made in brass for installation on metal doors. Diameter Ø 23mm. Weight 55 gr ART Roller switch contact. Dimension: 90x100x20 mm. Weight120 gr. IN Shock sensor for installation with windows any place where movement is not normal. White ABS Housing. Dimensions: 60 x 22 mm. H = 22 mm. Weight 30 gr. 3I GUARD Break glass volumetric detector. Designed to detect the frequency of breaking glass up to 20 meters away for the source. Led controls for alarm and memory. change over relay trigger output. alarm 1 A. Tamper protected white ABS housing. Current drain in standby 30 ma. Dimensions 50x76x19 mm. Weight. 70 gr. SISMIC ONE Seismico sensor immune to subsonic vibrations. Regulation with double sensativity Trimmer and Jumper based on the surface to protect. Incorporated pulse counter with 2,4,6,8 impulses and management with a 2 color LED which indicate TEST and PREALARM (30 sec.) when LED is green and ALARM mode if LED is red. Alarm memory for up to 10 Sismic 1 sensors installed on the same line. Magnet tamper protection with Optical relay compatable with all alarm panels. Working temperature from: 20 to +60 C. Working power from: 8,5V to 16V DC. Page 13

14 Electronic Key For Security Installations UNIKEY KIT Universal electronic key mother board. Can memorize up to 10 different SK-8 keys. If a programmed key is inserted into the receptacle, a relay with selectable functions will trigger. (ON/OFF or IMPULSE) The Unikey Kit is supplied with base station UNIKEY, 2 electronic keys SK-8 and 1 receptacle SK-8B. Also available SK-8 MAGIC & SK-8 LIVING Dimensions 76x76X19 mm. Weight: 50 gr. SK Supplementary electronic keys with 4 billion codes. SMD technology. ABS housing. Dimensions: 54x20x10 mm. Weight: 10 gr. SK-8B Remote receptacle for electronic key SK-8 with LED indications for: panel armed, panel disarmed, panel partially armed, and alarm memory. Built in nylon fibreglass material and maybe fixed to a surface with nut supplied. Diameter 23 h-30mm. Weight: 10g. SK-8M Same characteristics as the SK-8B but in version MAGIC. Dimensions: 24 x 44 x 30mm. Weight: 20 g. SK-8L Same characteristics as the SK-8B, but in version LIVING. Dimensions: 24x44x30 mm. Weight: 25 g Auxiliary D.C. Power Supply for Installations ASX mA 12 Vdc. Power supply in tamper protected robust ABS container with rechargeable battery compartment 12V. 2.2 Ah. Dimensions: 215x175x65mm. Weight 1.9 Kg. ASX A 12 Vdc. Power supply in tamper protected ABS housing with rechargeable battery compartment 12V 7.5Ah. Max. Dimensions: 230 x 285 x 85mm. Weight 1.50 Kg. Page 14

15 Accessories STE Electronic flasher with xenon flash tube. Suitable for installations to signal: Fire, Burglary, Gate opening, Hold-up or any other dangerous situation. Power: 12 Vdc. Current drain: 600 ma. Dimensions: Ø 40x70 mm. Weight: 55 gr. Until end of inventory. ART Foot operated hold-up device built in ABS housing. Dimensions: 81x79x25 mm. - Weight 120 gr. ART Foot operated hold-up device in steel housing with key reset. Dimensions: 305x144x89 mm. Weight 1,60 Kg. Minimum order 100 pcs ART Hold-up or panic button built in cast aluminium with key reset return. RED alarm button. Dimensions: 53x53x27mm. Weight: 65 gr. ART Panic button for use with any control panel or for an emergency. Dimensions: 75x14x22 mm Weight: 80gr. Batteries for Wireless Sensors CR-123 Lithium 3V 1,5Ah. Long life battery. Diameter: Ø 35 height 17 mm - Weight: 16 gr A-9 Alkaline 9 V long life battery. Dimensions: 26x48x17 mm A-12 Alkaline12 V long life battery. Diameter: Ø 10 height 28 mm Page 15

16