MARCH 2008 Elevator QEI / TURNOVER & Performance Report

Transcription

1 MARCH 2008 Elevator QEI / TURNOVER & Performance Report DUAL USE ELEVATOR 6 T-2212 TARGET BROLYN JUNCTION FLATBUSH AND NOSTRAND AVENUES BROLYN, NEW YORK ELEVATOR CONSULTING SERVICES, INC.

2 Equipment Inventory Control Type: Contract Speed: Machine Type: Door Equipment: Door Size/Type: Number of Stops: Floors Served: SELECTIVE COLLECTIVE MCE CONTROLLER EMS DOOR CONTROLLER 200 FPM HOLLISTER WHITNEY #74 GEARED OVERHEAD TRACTION EMS POWER BI-PARTING 8 0 WIDE X 8 0 HIGH FIVE (5) 3 FRONT / 2 REAR P2, P3, P4, T1, T2 Travel: Retail T T City/State Number: NEW YORK Capacity: Emergency Light: Alarm Bell: Maintenance Log: 8000 LBS NONE ITEMS IN RED ARE THE RESPONSIBILITY OF THE ELEVATOR CONTRACTOR ITEMS IN BLUE ARE THE RESPONSIBILITY OF THE BUILDING NI NEEDS IMPROVEMENT 2 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

3 PERFORMANCE Speed Up: Speed Down: Perform Up: P2 P3 Perform Down: P3 P2 Door Open: Door Close: 350 FPM 350 FPM 31.4 SEC 33.3 SEC 8.2 SEC 8.1 SEC Ride Quality Ride: Deceleration Up: Deceleration Down: Acceleration Up: Acceleration Down: Stop: Leveling: NI NEEDS IMPROVEMENT 3 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

4 Equipment Room Access: Headroom: Enclosure: Lighting: Cleanliness: Air Circulation,Ventilation: Pipes, Ducts, Non Elev: Parts: GFIC Receptacles: Fire Extinguisher: Guarding: Self Closing, Locking door: Numbering of units: Sprinkler in room: Lockable, Fused Disconnect: NONE NONE NO TAG GAUGE 110 Volt Disconnect: Shunt trip protection: Signage on door: NO NI NI NEEDS IMPROVEMENT 4 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

5 Control Panel Type of Control: Manufacturer: MICROPROCESSOR IMC-AC MCE Install Date: 9-04 Install Code: ASME NYC RS-18 Cleanliness: Identification: MCE JOB# SERIAL # Car Software Version: DIO V2.14 DDP MP A CGP Guarding: U. L. Label: CSA Telephone #: NI NEEDS IMPROVEMENT 5 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

6 Drive Model : Mfg : Fans : Cleanliness : Tool : F5 TORQMAX MCE 2 / N/A Output Power: AC Mot: 80 VA 75 OHP 2/4P50/60HZ Part #: Serial #: / Software Version: NO ID PROPRIETARY Input Cycles: 50/60 HZ Phase: Volts: Amps: 3 PH 440/480 V 105A NI NEEDS IMPROVEMENT 6 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

7 Components-Controller Relays: Enclosure/Open Style: ENCLOSED Contacts: Resistors: P.C. Boards / Timers: Boards : Wiring: Performance: Camera Wire: Telephone: Phone #: NO ID Main Relays -----PM1, PM2 Size: Mfg: Contacts: Wiring: Mounting: CL-10 GE NI NEEDS IMPROVEMENT 7 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

8 Machine Type: Cleanliness: Leaks: Noise: Sheave: Worm Shaft Seal: Thrust Bearing: Gear Condition: Oil: Oil Level: Motor Mfg: Stator: Rotor: Frame: HOLLISTER WHITNEY TRACTION 74 MACHINES RUSTY IN SPOTS NONE 60/1 RATIO IMPERIAL 405T HP: 60 AMPS: 63.5 RPM: 1165 NEMA Code: Grounded: E NI NEEDS IMPROVEMENT 8 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

9 Brake Type: Cleanliness: Lubrication: Core: Switch: Lining: Grommets: Pins: Drum: TRADITIONAL DRUM NONE N/A Coil: OHMS Tach Mfg: Model: INDUSTRIAL ENCODER CORP 1H950AL76R VDC: 5-15 NI NEEDS IMPROVEMENT 9 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

10 Governor Model: HW 207 Contract Speed: 200 FPM Rope size: 3/8 9.5 MM Cleanliness: Lubrication: Seals: Bearings: Jaws: Gears: Switches: Switch Trip Speed: Data Plate/Tripping Speed: Pull Through: 252 FPM 1.28 M/S 280 FPM 1.42 M/S 400 LBS 1779N 5 Year Load Test: PENDING Tagged: Annual No Load Test: Tagged: PENDING N/A N/A NI NEEDS IMPROVEMENT 10 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

11 Hoistway Selector Car Top Device/MCE Cleanliness: Tape: Guides: Magnets: Limit Switches Noise, Rollers: Operation: Type: GEM STND Rails Cleanliness: Lubrication: Type: Fastening: Roller Guides: ELSCO A- CAR ELSCO C- CWT Capture Device: N/A T / 18.5 LB N/A Counterweight Roller Guides : ELSCO- C Weight Containment : NI NEEDS IMPROVEMENT 11 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

12 Cable Condition Hoist: 10-5/8 LUBE - ADJUST Roping: 1:1 Install Date: 1-08 Governor: Governor Size: 3/8 Install Date: 1-08 Compensating Chains: Shackle Type Car: Shackle Type CWT Retainer Clips: Cable Tie Car: Cable Tie Cwt: Traveling Type: Suspension Spares: N/A WEDGE WEDGE 2/ROPE NI 1/2 - ALL 1/2 - ALL NEO Coax: NI NEEDS IMPROVEMENT 12 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

13 Hoistway Equipment Car Top Cleanliness: Maintenance Station: Stop Switch: Data Plate: Light: Light Guards: Guides: GFIC Recept: Escape door locked: Windows in Hoistway: N/A Multiple Hoistways: N/A Stenciled: Camera Box: Camera Power Rec : Hoistway Venting Existing: Motorized: Key Switch: Safety Bars: Size (3%): HAS VENT NORTH WALL FIRE COMMAND MESH NI NEEDS IMPROVEMENT 13 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

14 Door Operator / GAL MOVF Cleanliness: Door Protection: Lubrication: Belts: Chains: Hangers: Arms: Bearing: Noise: Tracks: Upthrusts: Restrictor: Gibs: Sprockets: Wiring: SCANNER NI NEEDS IMPROVEMENT 14 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

15 Car Enclosure 6 Ventilation: Car Sill: FAN NICKEL SILVER Walls: STAINLESS STEEL #4 Car Lighting: Ceiling: Position Indicators: Phase II Instructions: Handrails: Flooring: 10 FT CANDLES / FLORESCENT FLORESCENT FIXTURES SUSPENDED WITH EGG CRATE PANELS DIGITAL/ MAIN CAR OPERATING PANEL ROUND ON STAINLESS AT 8 & 24 NORAMENT Doors: STAINLESS STEEL #4 NI NEEDS IMPROVEMENT 15 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

16 ELEVATOR 6 Cleanliness: Entrance Equipment Lubrication: Tracks: Sills: NI Running Clearance: 1 ¼ Hangers: Gibs: Interlocks: Clutch Release Rollers: Noise: Upthrust: Closers: Braille: NI NI ADJUST LUBE ROLL PIN 60 TO CENTER Lobby Fire Box Existing: Machine Room Key: Elevator Keys: Lunar Key: Vent Key: Keys Tagged: NO NO NO NO NO NO NI NEEDS IMPROVEMENT 16 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

17 Car Operating Panel Type: Condition: INNOVATION VANDAL RESISTANT Height Compliance: Braille Identification: Buttons: Illuminated: Phone: Callback #: Alarm Button: Stop Switch: Emergency Light: Capacity Plate: Fire Fighters Instr: Phase II key sw: Fire Hat: Call Cancel: Certificated: PUSH TO TALK ADA COMPLIANT PROGRAMMED TO TSC NO ID PUSH / PULL LBS ENGRAVED ok NI NEEDS IMPROVEMENT 17 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

18 Hall Buttons: Type: Illuminated: Height: Mechanical: Lanterns: Fire Signage: Phase I key switch: Phase I instructions: INNOVATION VANDAL RESISTANT N/A NO EMBOSSED IN FIXTURE P1 LEVEL - RESET / OFF / ON NO NI NEEDS IMPROVEMENT 18 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

19 ELEVATOR 6 Pit Equipment Cleanliness: Car Buffer: Pit Bucket: Oil Return Line: Sheaves: Lights: Light Guards: Light Switch: Stop Switch: Ladder: GFIC Receptacles: Jack Seal: PVC Liner: N/A NI NEEDS IMPROVEMENT 19 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

20 Bottom of Car Cleanliness: Safeties: Trav cable suspension: Toe guard length: Isolation: Light Fixture: Light Guard: Guides: Receptacle: GFI Receptacle: NI NEEDS IMPROVEMENT 20 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

21 T-2212 TARGET BROLYN JUNCTION, NY DUAL USE ELEVATOR 6 CORRECTIVE ITEMS The following minimum items need corrective action taken. Documentation of completion is required. 1. Clean the controller. 2. Set the DAS board in the holder. 3. Secure the counterweights. Move the hold downs to the weights per code. 4. Replace the top right post roller of the counterweight roller guide assembly. 5. Replace the bottom right post roller of the counterweight roller guide assembly. 6. Adjust the front side chains to the limit cam assembly. 7. Adjust the DBG of front gate. 8. Adjust the final close, the doors slam hard. 9. Adjust the hoist ropes. 10. Lube the hoist ropes. 11. Confirm STE Parameter is not set for the construction mode. Should be the trip valve + 5 percent. NI NEEDS IMPROVEMENT 21 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY

22 T-2212 TARGET BROLYN JUNCTION, NY DUAL USE ELEVATOR 6 RECOMMENDATIONS GC Punch List 1. Install Elevator Equipment Room signage on the machine room door. 2. Add a florescent light over the machine. Requires 10 foot candles in the room. 3. Before adding steel angle, make sure there is only ¾ max running clearance to the hoistway door. Somehow taper the edge for cart movement. 4. Add flat stock by welding to entrance sill to close up the gap between the building sill and hoistway door to within code, T2 level. 5. Running clearance side to side from landing sill to hoistway door. Code is P4-7/8 1 1/2" P3-5/8 5/8 P2-1 1/2 1 T1 1 1/8 1 5/16 6. Replace the defective light fixture in the machine room. END OF REPORT NI NEEDS IMPROVEMENT 22 OF 22 T-2212 DUAL USE ELEVATOR 6 - SATISFACTORY