Room Pressure Monitor Deluxe

Transcription

1 MANUAL INSTALLATION Room Pressure Monitor Deluxe PMX Series v200 Issue Date: 03/26/ Price Industries Limited. All rights reserved.

2 TABLE OF CONTENTS TECH TIP Short circuit or incorrect wiring may permanently damage the controls or other equipment. Ensure proper wiring practices. The PMX is a 24 VAC controller. Do not apply any voltage above 24 VAC to controller. Application Support criticalcontrols@priceindustries.com Product Overview General... 1 Room Pressure Monitor Deluxe (PMX) Features...1 Room Pressure Sensor (RPS) Features...1 Room Pressure Interface (RPI-Standard) Features... 2 Included in Package...3 Optional Accessories...4 Installation & Mounting Instructions Isolation Room with Ante/Secondary Room...5 Single Isolation Room...6 Typical Wiring...7 Advanced Wiring...8 PMX Default Sequence of Operations...9 Commissioning of PMX...10 Display Navigation RPI Initial Startup Occupancy Modes/Service Menu...11 Controller Buttons...11 Service Menu Wizard Menu...13 Pressure Menu...14 Occupancy Menu...15 Timing Menu...15 Nurse Station Menu...15 Input Menu...16 Output Menu...19 BACnet Menu (Addressing)...21 RPI Setup Menu...22 Diagnostic Menu...24 Maintenance Troubleshooting...25 BACnet Point List...26

3 PRODUCT OVERVIEW General The Room Pressure Monitor Deluxe (PMX) is intended to provide intelligent pressure monitoring of isolation room and critical environments. Using the latest in microcontroller and sensor technologies, the PMX can measure extremely small pressures and display the readings on the local LCD display and over a BACnet network connection. PMX has support for up to 2 room pressure sensor (RPS) modules and can simultaneously monitor a primary and secondary (Ante) room. Room Pressure Monitor Deluxe (PMX) Features 16 bit high speed flash based microprocessor with watch dog timer, brown out reset ROOM PRESSURE MONITOR DELUXE (PMX) Multi-stage surge protection against voltage spikes on 24 VAC input Simple connections to room pressure sensors (RPS) using RJ-12 jacks 2 binary outputs rated at 0.5 amps each, protected with thermal fuse (RED LED on trip) 2 analog outputs (0-10 VDC), configurable for pressure and alarm outputs 2 binary inputs for door switches Pluggable terminal blocks BACnet MS/TP Client/Server stack BTL listed ROOM PRESSURE SENSOR (RPS) LED s for BACnet data TX/RX, BACnet wiring fault, and MS/TP termination Room Pressure Sensor (RPS) Features High accuracy room pressure sensor Quick keyed cable connection Indicator LED on sensor and PMX shows proper connection Stainless steel louvered plate for accurate readings and protection from cleaning priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 1

4 PRODUCT OVERVIEW Room Pressure Interface (RPI-Standard) Features Backlit 14x2 LCD Interface with true character display ROOM PRESSURE INTERFACE (RPI-STANDARD) LED side bars offer 180 degree viewing of current room status Green Safe Red Danger (exceeding low or high alarm set points) Blue - Unoccupied Password protected menu Easy to use MENU system for fast and simple setup of system Service port on back for use with Price LINKER2 setup software Included RJ45 plenum rated cable for fast, error free hookup Setup Wizard walk through setup of PMX when first powered up 2 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

5 Manual InstALLAtIon PMX series v002 Issue Date: 03/02/ Price Industries Limited. All rights reserved. ROOM PRESSURE MONITOR DELUXE PRODUCT OVERVIEW Included in Package Each PMX ships with the following items: INCLUDED ITEMS 1. PMX controller (mounted in enclosure) QTY: 1 ( ) 2. RPI-Standard (with backlit LCD screen) QTY: 1 ( ) 3. Plenum rated blue 25 foot (RJ-45) NETc12 cable QTY: 1 4. Room Pressure Sensor Main QTY: 1 (QTY: 2 if monitoring secondary room as well) 5. Room Pressure Sensor Ref QTY: 1 (QTY: 2 if monitoring secondary room as well) 6. 2 Gang Drywall mounting bracket QTY: 2 (QTY: 4 if monitoring secondary room as well) 7. Plenum rated green 25 foot (RJ-12) cable QTY: 1 (QTY: 2 if monitoring secondary room as well) 8. Kink resistant air tubing 18 QTY: 1 (QTY: 2 if monitoring secondary room as well) 9. USB stick (1GB) containing manuals/website links/etc QTY: 1 ( ) 1. PMX CONTROLLER 2. RPI-STANDARD 3. PLENUM RATED BLUE 25 FOOT 7. PLENUM RATED GREEN 25 FOOT 8. KINK RESISTANT AIR TUBING 18" 9. USB STICK - 1GB 10. Price Electronics Flat head screwdriver (0.1 tip) QTY: 1 ( ) 4. ROOM PRESSURE SENSOR - MAIN 10. FLAT HEAD SCREWDRIVER 11. This instruction manual QTY: 1 Please ensure you have all components before proceeding. Inspect components for shipping damage. Do not install any components that appear damaged, contact your local Price sales rep for quick ship replacements. For the latest information and videos please visit com/resources/literature/brochures. aspx 5. ROOM PRESSURE SENSOR - REF. 6. DRYWALL MOUNTING BRACKERS Room Pressure Monitor Deluxe 11. INSTRUCTION MANUAL priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 3

6 PRODUCT OVERVIEW Optional Accessories The PMX has an option for a remote nurses station. The nurses station can select between Isolation or Setback mode. Please ensure you have the correct Nurses' station for your isolation room. NURSE STATION KEYSWITCH - KEYLESS NOTE: Due to unpredictable location of Nurses station wiring/ cabling is by others. Recommend AWG copper 6 conductor plenum rated wire. The maximum distance the Nurses' station can be mounted from the PMX monitor is 100 feet. Another option is a surface mount door switch which will tell the PMX when door(s) are left open. These are wired to the binary inputs. (Dry Contacts, no voltage.) Surface Mount Magnetic Door Switches QTY: 1 (QTY: 2 if secondary room is used) NURSE STATION KEYSWITCH - SETBACK / ISOLATION SURFACE MOUNT MAGNETIC DOOR SWITCHES 4 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

7 INSTALLATION & MOUNTING INSTRUCTIONS Isolation Room with Ante/ Secondary Room The PMX supports ANTE/Secondary rooms with the addition of another RPS assembly. Simply connect the 2nd RPS to the RJ12 port labeled Secondary Sensor. However there are different options for the pressurization strategy when multiple RPS sensors are used. Such as those shown here. Once you have selected the monitoring strategy needed, you can begin mounting components. NOTE: See Page 6 for main and reference sensor installation instructions ISOLATION ROOM & ANTE/SECONDARY ROOM CONFIGURATIONS 1. RECOMMENDED PRIMARY ROOM AND ANTE/SECONDARY ROOM BOTH REFERENCE THE CORRIDOR/HALLWAY ISOLATION/PRIMARY ROOM ANTE/SECONDARY ROOM 2. PRIMARY ROOM REFERENCES ANTE/SECONDARY ROOM CORRIDOR PRIMARY SENSOR SECONDARY SENSOR ISOLATION/PRIMARY ROOM CORRIDOR PRIMARY SENSOR ANTE/SECONDARY ROOM SECONDARY SENSOR priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 5

8 INSTALLATION & MOUNTING INSTRUCTIONS Single Isolation Room Ensure you have all components necessary for installation. Inspect components for signs of shipping/handling damage. Do not proceed if you suspect any components are damaged. 1. Mount the Price Room Pressure Monitor Deluxe (PMX) enclosure in the plenum space above the door to the room to be monitored. Price recommends mounting the unit in the hallway servicing the room to be monitored. The PC must NOT be installed outdoors or in an enclosure that is outdoors. The PC is not environmentally rated for mounting in these locations. Using 4 screws (by others) mount the PC enclosure horizontally to a flat, secure and accessible surface. Ensure the electrician can access the terminal blocks/disconnect switch. 2. Next install the Room Pressure sensor (RPs) assembly. The RPsMain sensor should be installed in the hallway using the drywall bracket supplied. The RPs-Reference sensor must be installed within 12 inches of the Main Sensor. NOTE: The Main Sensor has a black cable connector and brass airflow nipple, while the Reference Sensor only has a brass airflow nipple (Sensor made of fire retardant antibacterial plastic). 3. Mount the Room Pressure Interface near the doorway using a standard electrical box or drywall anchors (by others) at a height of 5 feet. Ensure LED bars are not blocked by other devices on wall (Interface made of stainless steel with fire retardant plastic sensor cover). INSTALLATION EXAMPLES MOUNTING HOLES DISCONNECT SWITCH (ENSURE OFF AT THIS TIME) HIGH VOLTAGE CONNECTION 120/208/240/277 VAC (50 VA) MOUNTING HOLES RPS-REFERENCE SENSOR ASSEMBLY MOUNTED IN ISOLATION ROOM. FIRMLY ATTACH AIR TUBING (SUPPLIED) TO BRASS PRESSURE TAP USING SUPPLIED KINK RESISTANT TUBING. RPS-MAIN SENSOR ASSEMBLY MOUNTED IN CORRIDOR/HALLWAY. FIRMLY ATTACH AIR TUBING TO BRASS PRESSURE TAP. GENTLY PLUG GREEN C25 CABLE TO BLACK, QUICK CONNECTION ON BACK OF SENSOR ASSEMBLY. ROUTE OPPOSITE END OF CABLE TO THE PMX, PLUGGING THE RJ-12 (TELE- PHONE TYPE) CONNECTION INTO 'PRIMARY SENSOR' INPUT. 6 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

9 NORMAL ALARM ROOM PRESSURE MONITOR DELUXE R INSTALLATION & MOUNTING INSTRUCTIONS CRITICAL CONTROLS Control Number Typical Wiring Ensure proper voltage is available for the PMX transformer in the enclosure. Double check all labels and wiring before applying high voltage. NOTE: The PMX is a 24 VAC low voltage controller. Do not apply any voltage above 24 VAC to controller. 1. Ensure disconnect switch is off. Route high voltage line to L1/L2(N) terminal block using knockout/cable clamp (by others). 2. Connect green RJ12 (telephone type 6 position) cable to jack labeled Primary Sensor on PMX. Connect the other end with the black (locking) connector into RPS-Main. Ensure cable is not twisted, kinked or pinched during installation. The green LED above Primary Sensor will be green when powered up and functioning properly. 3. Connect blue RJ45 (network type 8 position) cable to jack labeled RPI on PMX. Connect the other end to the RPI mounted on the wall. WIRING ROOM PRESSURE INTERFACE (RPI) Enter Menu Mute Emergency CAT5E CABLE BY PRICE PLUG AND PLAY RJ12/LOCKING CIRCULAR CONNECTION ON SENSOR(S) LINKER T-STAT SECONDARY SENSOR COM 10 PRIMARY SENSOR EXPANSION STA ANALOG INPUTS PMX PRESSURE MONITOR DELUXE B/- HLH A/+ TRM NET COM FLT AO2 AO1 BO2 BO1 TX RX BACnet MS/TP BI2 BI1 STA PRICE RJ COM 1 2 COM 1 COM * BACnet MSTP From Previous Device (or Router) to next device DOOR SWITCH (OPTIONAL) 3 VAC 24 PRIMARY PRESSURE SENSOR (RPS) N/L2 L1 LEGEND FACTORY ELECTRICAL WIRING 120V Power In FIELD ELECTRICAL WIRING CAT5E CABLE PROJECT: ENGINEER: CUSTOMER: PCC CR PM SUBMITTAL DATE: SPEC. SYMBOL: 2014/11/07 C Copyright PRICE INDUSTRIES 2014 REV priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 7

10 NORMAL ALARM ROOM PRESSURE MONITOR DELUXE INSTALLATION & MOUNTING INSTRUCTIONS R Advanced Wiring Control Sequence CRITICAL CONTROLS Number This section covers advanced wiring that includes BACnet MS/TP option, ANTE room (secondary sensor), binary inputs (door switches), and binary outputs (alarms). NOTE: All terminals labels COM are tied to 24 VAC common. Please observe polarity at all times. 1. BACnet MS/TP wiring can be done using the 3 position pluggable terminal block or the Price RJ45 connection. Ensure proper 24 VAC hot/common polarity between all devices! Also ensure 24 VAC common is earth grounded. Set BAUD rates and addresses using the SERVICE MENU on the RPI. 2. If monitoring an ANTE/Secondary room connect the second RPS assembly to the RJ12 port labeled Secondary Sensor. A green LED indicates proper connection/power. 3. There are 2 Binary Inputs (BI1, BI2). These are wired to optional door switches. BI1 monitors the primary room, while BI2 monitors the secondary room. Default type is intended for normally closed type switches. Note: These are dry contacts. No voltage should ever be applied. See the SERVICE MENU for configuration options. WIRING ROOM PRESSURE INTERFACE (RPI) Enter Menu CAT5E CABLE BY PRICE Mute Emergency PLUG AND PLAY RJ12/LOCKING CIRCULAR CONNECTION ON SENSOR(S) SECONDARY PRESSURE SENSOR (RPS) PRIMARY PRESSURE SENSOR (RPS) LINKER T-STAT SECONDARY SENSOR PRIMARY SENSOR COM EXPANSION STA ANALOG INPUTS N/L2 L1 PMX PRESSURE MONITOR DELUXE B/- HLH A/+ TRM NET COM FLT AO2 AO1 BO2 BO1 TX RX BACnet MS/TP BI2 BI1 STA VAC PRICE RJ COM 1 2 COM 1 COM 24 BACnet MSTP From Previous Device (or Router) to next device DOOR SWITCH (OPTIONAL) * NURSES STATION NURSES STATION WITH KEY SWITCH WITH KEY SWITCH NORMAL ALARMNORMAL ALARM 6 NEUTRAL 5 POSITIVE NEUTRAL POSITIVE There are 2 Binary Outputs (BO1, BO2). These are wired to another device that can read in alarm statuses. These are intended for monitoring and do not affect the operation of the PMX whether they are used or not. See the SERVICE MENU for options. LEGEND FACTORY ELECTRICAL WIRING FIELD ELECTRICAL WIRING CAT5E CABLE PROJECT: ENGINEER: CUSTOMER: SUBMITTAL DATE: 120V Power In SPEC. SYMBOL: PCC /07/23 CRITICAL CONTROLS HCA PEARLAND PMX WIRING OVERVIEW R 5. There are 2 Analog Outputs (AO1, AO2). These are wired to another device that can read in alarm statuses. These are intended for monitoring and do not affect the operation of the PMX whether they are used or not. See the SERVICE MENU for options. C Copyright PRICE INDUSTRIES 2014 REV A 8 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

11 INSTALLATION & MOUNTING INSTRUCTIONS PMX Default Sequence of Operations The PMX can function in standalone mode (not networked to any building automation systems (BAS)) or can be integrated using the BACnet MS/TP port. When configured for single (primary) room operation the PMX can be set to monitor POSITIVE or NEGATIVE pressure. Alarms for LOW/HIGH pressure are fully field configurable. The PMX has 3 primary modes: Mode Status LCD Display LED Bars Alarm Negative/Positive Pressure Monitoring (Room Active) Negative/Positive Pressure Monitoring (Room Occupied) Neutral (Room Unoccupied) SAFE - Pressure reading within LOW / HIGH set points ALARM - Pressure reading within LOW / HIGH set points UNOCCUPIED Pressure measured but no alarms Primary Room W.C. ALARM! W.C. Primary Room Unoccupied GREEN RED BLUE OFF ON OFF Occupied SAFE (proper pressure detected) Occupied ALARM (pressure out of range either low or high set point) Unoccupied Pressure monitored and displayed but no alarms When occupied the PMX will monitor and display the primary room pressure. If the pressure reading is within the LOW and HIGH alarm set points the LED bars will be green and the alarm will be off. If the pressure reading is outside of either the LOW or HIGH alarm set points the LED bars will turn RED and the local (RPI-Standard) alarm will turn on. If networked using BACnet a variable will show the type of alarm. If the Room Pressure Sensor (RPS) is unplugged from the PMX while in occupied mode the LED bars will turn RED and the alarm will turn on. priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 9

12 INSTALLATION & MOUNTING INSTRUCTIONS Commissioning of PMX When first powered up (and startup screens have been displayed) the RPI will display: PMX Awaiting Setup To access the service menu hold Enter Menu for 5 seconds. This menu is password protected for safety. Please contact your local rep for Passcode or contact - Price Critical Controls: criticalcontrols@priceindustries.com This means the PMX has not been setup and is currently not monitoring. There are two options for setting up the PMX, either by the LCD screen or the LINKERSOFT software (latest available at priceindustries.com/software/linkersoft). The LCD screen is a convenient way to setup the PMX and allows full control of all variables through a menu system. This does not require a computer. The service menu is passcode protected to prevent typical users from changing important settings. Another option is to use the LINKER2 USB service tool with LINKERSOFT windows software. This of course requires a Windows Laptop with USB port, but offers the advantage of printing (to PDF) a commissioning report. Install the LINKERSOFT software from the USB stick included with your PMX. (Directory Linkersoft/setup.exe) After installation connect the LINKER2 to your laptop with the included USB cable. Plug the other end into your RPI (LINKER/SERVICE) using the included RJ12 to MTA-100 jack. DEMONSTRATION - W/ BACK OF RPI SHOWN PMX must be powered up and make sure that the RPI is connected with the RJ45 cable. 10 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

13 DISPLAY NAVIGATION RPI Initial Startup When the RPI is first powered from the PMX controller, it will display the following information: (Also press both UP/DOWN at same time to show this screen anytime.) PRICE ELECTRONICS Start-up screen INTERFACE STANDARD MODEL PMX interface PCC LCD V3.XX.X LCD - Firmware Version V3.xx or higher LOADING: 0-100% Loading Screen RPI Interface pulls in variables from PMX Note:a sequence number of 0 means the stat has NOT been calibrated PMX VERSION 1.XX PMX Controller - Firmware Version 1.xx or higher MAC ADDRESS 1 Displays current MAC Address (local MS/TP segment) Must be unique to MS TP segment DEVICE INST Displays current Device Instance (System address) Must be unique to building PRIMARY ROOM SETBACK After start up LCD will display default screens depending on mode of operation Occupancy Modes / Service Menu The RPM has 2 operating modes - occupied and unoccupied (sometimes referred to as setback). To change Occupancy mode: Quickly press Enter Menu button, Occ. Passcode will display. Enter: Down / Up / Up / Down Using the Up/Down button select either Isolation (alarms active) or Setback (alarms disabled). Press Enter Menu to save and exit. CONTROLLER Controller Buttons Up/Down Button Used for menu selection and adjustment - press both up and down at same time to display RPI Startup screens. Enter Menu Used to Enter service menu(s). The menu(s) are password protected. Mute Used to temporarily mute the local alarm for a certain number of minutes. Emergency Used to trigger emergency mode. Local Alarm will sound and BACnet point will change to Alarm alerting the front end system. priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 11

14 DISPLAY NAVIGATION Service Menu The service menu contains all setup and configuration parameters. Each PMX ships with factory defaults, but virtually all settings can be adjusted in the field. All main menus are listed on this page. Use the Wizard and/or below menus to setup the PMX for your application. To access the service menu hold Enter Menu for 5 seconds. This menu is password protected for safety. Please contact your local rep for Passcode or contact - Price Critical Controls: or criticalcontrols@priceindustries.com PRESSUREALRMS Allows setting of pressure alarm set points (high and low), room type either negative or positive OCCUPANCY Allows user to force occupied/unoccupied modes TIMING Allows configuration of alarm delays NURSE STN. Allows configuration of nurses station alarms, key switch and LED indicators INPUT Allows configuration of binary and analog inputs OUTPUT Allows configuration of binary and analog outputs BACNET Allows setup of BACnet addresses, baud rates for MS/TP RPI SETUP Allows setup of LED bars, sounds and push buttons WIZARD Steps the user through a simple setup process. Intended to get PMX up and running quickly. Wizard runs on first power up, but can be re-run at any time. DIAGNOSTIC Contains diagnostic information or allows the controller to be reset to factory defaults 12 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

15 DISPLAY NAVIGATION Wizard Menu The first time the PC is powered on, the connected RPI will step through the setup wizard. This allows a quick setup of the parameters needed. During the wizard, press the 'Enter Menu' button to proceed through the menus. There is no back button, so take time to ensure the correct information is entered. During the setup wizard, if incorrect information has been entered, there are two options available; 1. Proceed through the wizard and correct the information afterwards 2. Unplug the interface. This will cause the setup wizard to start from the beginning WIZARD PRI ISO MODE NEGATIVE MONITOR SECRM YES Pri Iso Mode - Primary Isolation Mode. This sets the primary room to be either positively or negatively pressured. Monitor SecRm - Monitor Secondary Room. This option enables the ability to monitor the secondary room. A secondary room pressure sensor is required. LOWPRESSALARM "W.C. Low Pressure Alarm - Set the minimum primary room pressure condition that is acceptable before going into alarm mode. HI PRESSALARM "W.C. High Pressure Alarm - Set the maximum primary room pressure condition that is acceptable before going into alarm mode. SEC ALARM LO "W.C. Low Pressure Alarm - Set the minimum secondary room pressure condition that is acceptable before going into alarm mode. SEC ALARM HI "W.C. High Pressure Alarm - Set the maximum secondary room pressure condition that is acceptable before going into alarm mode. ALARM DELAY 30 SEC. User set time delay between an alarm condition being detected and an alarm sounding. Default: 30 sec. RPI MUTE TIME 15 MIN. MAC ADDRESS 1 DEVICE INST. 0,158,001 BAUD RATE Amount of time the interface, if in alarm mode, will remain muted after the mute button has been pressed. Visual alarm will continue to be displayed. Default: 15 min. Set the controller's BACnet MS/TP MAC address. Range NOTE: To prevent network issues, ensure no duplicate MAC addresses exist on the same MS/TP physical segment. Device Instance - This is the unique address for the controller. NOTE: To prevent network issues, set in tiers. Must be unique across entire network. Example: First floor; 101, 102, 103. Second floor; 201, 202, 203. Baud Rate - The rate with which the controller communicates over BACnet. Baud rate must be consistent across the MS/TP physical segment. Options are: 9600, 19200, 38400, and SETUP WIZARD COMPLETE SEE MANUAL FOR ADV SETUP **Controller will now reset** priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 13

16 DISPLAY NAVIGATION Pressure Menu Once in the service menu, scroll down and press 'Enter Menu' to enter the Pressure menu. PRESSUREALRMS PRESSURE PRIMARY RM Primary Room pressure alarm options ROOM MODE NEGATIVE Configure whether the room will be negative pressure or positive pressure. LOW CAUTION NO CAUTION HIGH CAUTION NO CAUTION LOW PRESSALARM NO ALARM HI PRESSUREALARM " W.C. Minimum user set room pressure value that is acceptable before going into caution mode. Default: No Caution. Maximum user set room pressure value that is acceptable before going into caution mode. Default: No Caution. Minimum user set room pressure value that is acceptable before going into alarm mode. Maximum user set room pressure value that is acceptable before going into alarm mode. Default: " W.C. PRESSURE SECONDARY RM Secondary Room pressure alarm options MONITOR SECRM NO Monitor Secondary Room - Select if the monitor is monitoring a secondary room. Yes or No. Default: No. SEC RM MODE NEGATIVE Configure whether the room will have negative pressure or positive pressure. SECCAUTIONLO NO CAUTION SECCAUTIONHI NO CAUTION SEC ALARM LO NO ALARM SEC ALARM HI NO ALARM Minimum user set room pressure value that is acceptable before going into caution mode. Default: No Caution. Maximum user set room pressure value that is acceptable before going into caution mode. Default: No Caution. Minimum user set room pressure value that is acceptable before going into alarm mode. Default: No alarm. Maximum user set room pressure value that is acceptable before going into alarm mode. Default: No alarm. 14 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

17 DISPLAY NAVIGATION Occupancy Menu OCCUPANCY Timing Menu TIMING ROOM MODE ISOLATION Room Mode (default) will display Setback/Isolation. This mode can also be displayed as Occupied/Unoccupied. NOTE: This variable cannot be changed if a Nurses' Station with Key Switch is connected. ALARM DELAY 30 SEC. CAUTN INDELAY NO RPI MUTE TIME 15 MIN. DOORALARMDLAY 60 SEC. DOOR RECOVERY 5 SEC. This is the time between an alarm being sensed and the alarm sounding (5-3,600sec). This gives the sensor time for the pressure to correct itself without alarm being sounded. Default: 30 seconds Caution In Delay - Option for the monitor to go into caution mode during the alarm delay. Default: No. Amount of time the interface, if in alarm mode, will remain muted after the mute button has been pressed. Visual alarm will continue to be displayed. Default: 15 min. Door Alarm Delay - Amount of time that a door can be ajar before the monitor goes into alarm mode. Default: 60 sec. Door Recovery This allows for the room pressure to stabilize for a number of seconds after the door(s) have been closed (5-600 sec). Default: 5 seconds. Nurse Station Menu NURSE STN. CAUTIONCONFIG BLINK GREEN ALARM TYPE WAIL Caution Configuration - Selection of LED color/blink during caution. Choose from: Solid Green, Blink Green, Solid Red + Green, Solid green + blinking red, Blinking red/green, Solid red, Blinking red. Default: Green Solid. Selects the alarm sound type. Choose from: Wail, 2kHz tone, Red Alert, No Tone. Default: Wail. ALARM CONFIG BLINK Alarm Configuration - Select the LED action during alarm. Choose from: Blink, Solid ON, Off. Default: Blink. MUTE TIME 15 MIN. Configure the amount of time the remote panel will mute for when the mute button is pressed. Default: 15min. KEYSWOVERRIDE NO Key Switch Override - This allows you to override the remote panel key switch when set to Yes. Default: No (Recommend: No). priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 15

18 DISPLAY NAVIGATION Input Menu INPUT INPUT SENSORS PRISENSREVERSE NO Primary Sensor Reversed - Gives the option to reverse the primary sensor. Select Yes to electronically switch the reference sensor with the main sensor. Default: No. SECSENSREVERSE NO Secondary Sensor Reversed - Gives the option to reverse the secondary sensor. Select Yes to electronically switch the reference sensor with the main sensor. Default: No. SWITCH PORTS NO Give the ability to switch the secondary and primary sensor ports. Default: No. PRISCALEFACTR Primary Scale Factor - Adjust the scale for the primary sensor. PRISENSOFFSET 0.000" W.C. Primary Sensor Offset - Adjust the pressure offset for the primary sensor. SECSCALEFACTR Secondary Scale Factor - Adjust the scale for the secondary sensor. SECSENSOFFSET 0.000" W.C. Secondary Sensor Offset - Adjust the pressure offset for the secondary sensor. INPUT BINARY INPUTS BI1 CONFIG DISABLED BI2 CONFIG DISABLED Disabled Door - N/O: Door switch(dsw) is a Normally Open DSW Door - N/C: DSW is Normally Closed Alarm on Clo - Alarm On Close. An alarm is triggered when the binary input is contacted (closed). Alarm on Opn - Alarm On Open. An alarm is triggered when the binary input is not contacted (open). Cautn on Clo - Caution On Close. Monitor goes into caution mode when the binary input is contacted (closed). Cautn on Opn - Caution On Open. Monitor goes into caution mode when the binary input is not contacted (open). Occ. On Clo - Occupied On Close. Monitor goes into Occupied mode when the binary input is contacted (closed). Unocc. On Clo - Unoccupied On Close. Monitor goes into Unoccupied mode when the binary input is contacted (closed). Refer to BI 1 for options CAUTIONONDOOR YES Caution On Door - If the door(s) is ajar, the monitor will go into caution mode. Default: Yes. Continued on next page ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

19 DISPLAY NAVIGATION Input Menu Continued INPUT ANALOG INPUT EXTHERM TEMP F External Thermistor Temperature - Displays the temperature that the external thermistor is reading. Will display F if there is no PMX connected, or if there is no thermal coupler connected to the PMX. If PMX is present and no thermistor detected, F will be displayed. AI SELECT AI 3 Select the analog input to configure. AI 3 TYPE VENTURI FLOW Select the type of analog signal that the controller will be receiving: 1. Volts - Tells the controller to expect a voltage signal on this input 2. Venturi Flow - Tells the controller to expect to receive an airflow signal from a venturi valve 3. Terminal Flow - Tells the controller to expect to receive an airflow signal from a terminal unit 4. AirChngLinear - Air Change Linear. Set the input to Air Change Linear only if it is reading in the airflow rate from the venturi valve. Air change is calculated using the linear airflow signal from the valve and the user set room size. Advanced option, contact your Price Critical Controls rep. This is for display over BACnet, no control function for this feature 5. AirChng Press - Air Change Pressure. Set the input to Air Change Pressure only it is reading in the signal from a velocity pressure sensor from a terminal unit. Air Change is calculated using the pressure signal from the velocity pressure sensor and the user set room size. Advanced option, contact your Price Critical Controls rep. This is for display over BACnet, no control function for this feature 6. Pressure - Tells the controller to expect a pressure signal on this input such as a venturi valve pressure signal AI 3 OFFSET 0.00 VDC Allows voltage offset adjustments of the chosen analog input. SCALE FACTOR AI3 LOW ALARM DISABLED AI3 HIGH ALARM DISABLED AI3 LOW CAUTN DISABLED Adjust the scale factor of the selected analog input to match a measured value. Adjust this value when working with the balancer to correct the airflow reading. Allow the user to configure at which value to sound the low alarm for selected analog input. NOTE: Often used to enable alarm when venturi valve pressure, voltage, air change rate, or airflow drops below the operating range. Unit depends on the analog input selected. Allow the user to configure at which value to sound the high alarm for selected analog input. NOTE: Often used to enable alarm when venturi valve pressure, voltage, air change rate, or airflow rises above the operating range. Unit depends on the analog input selected. Allow the user to configure at which value to sound the low caution alarm for selected analog input. NOTE: Often used to enable alarm when venturi valve pressure, voltage, air change rate, or airflow drops below the operating range. Unit depends on the analog input selected. Continued on next page... priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 17

20 DISPLAY NAVIGATION Input Menu Continued AI3 HIGHCAUTN DISABLED AI3 CURRENTVAL 0.00 VDC Allow the user to configure at which value to sound the high caution alarm for selected analog input. NOTE: Often used to enable alarm when venturi valve pressure, voltage, air change rate, or airflow rises above the operating range. Unit depends on the analog input selected. Current Value - Display the current value on the selected analog input. 18 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

21 DISPLAY NAVIGATION Output Menu OUTPUT OUTPUT BINARY OUTPUT B01 USAGE UNUSED BO2 USAGE NORMAL Unused Alarm - The binary output will activate if the monitor goes into Alarm mode Caution - The binary output will activate if the monitor goes into Caution mode Normal - The binary output will activate while the monitor is in Normal operating mode Neutral - The binary output will activate while the monitor is in Neutral operating mode Caution/Alarm - The binary output will activate if the monitor goes into either Caution or Alarm mode Low Pressure - The binary output will activate if the pressure drops below the Low Pressure value High Pressure - The binary output will activate if the pressure exceeds the High Pressure value PriLoPressure - The binary output will activate if the Primary Room's pressure drops below the Low Pressure range PriHiPressure - The binary output will activate if the Primary Room's pressure is above the High Pressure range SecLoPressure - The binary output will activate if the Secondary Room's pressure drops below the Low Pressure range SecHiPressure- The binary output will activate if the Secondary Room's pressure is above the High Pressure range Emergency - The binary output will activate if the Emergency button has been pushed Door - The binary output will activate if a door connected to the monitor is ajar PriRm Alarm - The binary output will activate if the Primary Room Alarm is triggered SecRm Alarm - The binary output will activate if the Secondary Room Alarm is triggered See BO2 for options Continued on next page... priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 19

22 DISPLAY NAVIGATION Output Menu Continued OUTPUT ANALOG OUTPUT A01 USAGE PRIRM SPLYACT A02 USAGE UNUSED Unused PriPress5V=0 - Primary Room Pressure 5V = 0" W.C. This option outputs a analog voltage signal, starting at 5VDC, relative to the primary room's pressure reading. For 0"W.C. the monitor will output 5VDC PriPress0-10V - Primary Room Pressure 0-10V. This option outputs a 0-10V signal relative to the primary room's pressure reading. SecPress5V=0 - Secondary Room Pressure 5V=0" W.C. This option outputs a analog voltage signal, starting at 5VDC, relative to the secondary room's pressure reading. For 0"W.C. the monitorwill output 5VDC SecPress0-10V- Secondary Room Pressure 0-10V. This option outputs a 0-10V signal relative to the secondary room's pressure reading. Alarm 5V - Output a 5 VDC signal when in alarm mode. Output will return to 0V when alarm is cleared. PriAlarm 5V - Primary Room Alarm. If the primary room goes into alarm, this tells the monitorto output a 5VDC signal out of the selected output. Output will return to 0V when alarm is cleared. SecAlarm 5V - Secondary Room Alarm. If the secondary room goes into alarm, this tells the monitorto output a 5VDC signal out of the selected output. Output will return to 0V when alarm is cleared. PriRm SplyAct -Primary Room Supply Actuator. This sets the output to control the supply valves/dampers actuators for the primary room. PriRm ExhAct - Primary Room Exhaust Actuator. This sets the output to control the exhaust valves/dampers actuators for the primary room. SecRm SplyAct - Secondary Room Supply Actuator. This sets the output to control the supply valves/dampers actuators for the secondary room. SecRm ExhAct - Secondary Room Exhaust Actuator. This sets the output to control the exhaust valves/dampers actuators for the secondary room. Reheat - Sets the selected analog output to control the reheat valve signal. The analog output will output a voltage when there is a call for heating. Humidifier - Sets the selected analog output to control the humidifier signal. The analog output will output a voltage when there is a call for humidity. See AO1 for options 20 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

23 DISPLAY NAVIGATION BACnet Menu (Addressing) NOTE: BACnet communication lines MUST NOT be run next to power lines! High voltage lines, VFD's, ballasts and other electrical devices generate noise which can affect the BACnet network reliability. Route BACnet network wires away from these types of devices. BACNET MAC ADDRESS 1 DEVICE INST. 158,001 BAUD RATE RS-485 TERM. DISABLED BACNET WRITE SAFE Set the controller's MAC address. Maximum 99. NOTE: To prevent network issues, ensure there are no other monitors that share the same MAC address. Device Instance - This is the unique address for the monitor. NOTE: To prevent network issues, ensure there are no other monitors that share the same Device Instance. Baud Rate - The rate with which the monitorcommunicates over BACnet. Options are: 9600, 19200, 38400, and Default: This enables the RS-485 termination on the PMX MS/TP BACnet port. Remember, only terminate the network twice in total, once at the beginning and once again at the end of the network. BACnet Write. SAFE: Allows for non-critical points (ie: Room temperature set point) to be written/edited over BACnet. Critical points are read-only. DANGER: Allows for critical points (ie: Room alarm set point) to be written/edited over BACnet. priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 21

24 DISPLAY NAVIGATION RPI Setup Menu RPI SETUP EMERG BUTTON DISABLED LITEBAR-NORM. GREEN LITEBAR-ALARM BLINK RED LITEBAR-CAUT. YELLOW Emergency Button This button on the RPI can be enabled or disabled Light Bar in Normal Mode This sets the color of the light bar while in normal conditions (no alarm, no caution and occupied room). Light Bar in Alarm Mode This sets the color of the light bar while in alarm conditions. Light Bar in Caution Mode This sets the color of the light bar while in caution conditions. LITEBAR-UNOCC. SKY BLUE ALARM TYPE WAIL OCCUPANCYNAME SETBACK/ISO Light Bar in Unoccupied Mode This sets the color of the light bar while in unoccupied mode. Alarm Type This sets the sound of the alarm. Choose between three different alarm sounds; No tone, Steady 2Khz, Wail, Red Alert Occupancy Name Selects the name displayed for Room Mode. Choose between "Alarm mode", "Setback/Isolation", "Nutrl/Pos-Neg", or "Occupancy". Display Code Provides options for what is displayed, such as room pressure, occupancy, and etc. Add the values together and enter the sum to display multiple screens of information. Ex: 2+16=18 will display Primary Room/ W.C. and Secondary Room/ W.C. DISPLAY CODE Main Screen Displays Value Binary Primary Room Negative Primary Room " W.C. Negative " W.C. Seconday Room Negative Secondary Room " W.C. System Normal (Available if no secondary room OR both pri/sec isolation modes match) Negative DisplayOptions Opens up the Display Options menu. See below. Continued on next page ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

25 DISPLAY NAVIGATION RPI Setup Menu Continued DISPLAY OPTIONS SETPOINT ONLY Choose what is displayed on the interface. Options are: 1. Temp and SetP - Temperature displayed on main screen, setpoint displayed/adjusted when up/down buttons are. 2. Setpoint Only - Displays the setpoint only 3. RoomTemp Only - Displays the room temperature only. No setpoint adjustment allowed. 4. CtlName/SP en - Display the monitor name and temperature setpoint, and enable the setpoint to be adjustable 5. CtlName/Spdis - Display the monitor name and temperature setpoint, and disable the ability to adjust the setpoint 6. NameTemp/Spen - Display the monitor name, room temperature, and temperature setpoint. Enable the setpoint to be adjustable 7. NameTemp/SPds - Display the monitor name, room temperature, and temperature setpoint. Disable the ability to adjust the setpoint 8. Name and Setp - Display the user set name and the temperature setpoint. 9. Temp&Humidity - Display the room temperature and humidity reading* 10. Humidity - Display the room's current humidity reading* NOTES: All options require a Price Thermostat. *Option requires the Price Humidity Thermostat to function correctly priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 23

26 DISPLAY NAVIGATION Diagnostic Menu DIAGNOSTIC BACNET HEALTH 100% BACnet Health - Shows current status of BACnet MS/TPconnection. No connection means no active connection. 100% means good connection. 0-99% means possible connection issues, check wiring, addresses, and polarity. PRIMARYSENSOR CONNECTED Primary Sensor - Shows current status of Primary room Pressure Sensor. Connected or disconnected. PRIMARYSENSOR 0.000" W.C. Primary Sensor - Shows current reading of Primary Sensor in inches of water. SECONDARYSENS DISCONNECTED Primary Sensor - Shows current connection status of Secondary Sensor. Connected or disconnected. SECONDARYSENS 0.000" W.C. Secondary Sensor - Shows current reading of Secondary Sensor in inches of water. KEYSWITCHPSTN NO KEY Key Switch Position - Displays the current key switch position RPC EXPANSION CONNECTED Room Pressure Controller Expansion - Displays the connection status of the PMX expansion. DIAGNOSTIC: LOAD DEFAULTS Reset all user settings back to factory default. DIAGNOSTIC: RESETCONTROLR Reset Controller - Reboots the controller, mimicking a power cycle. no settings will be lost. 24 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

27 MAINTENANCE Troubleshooting Problem Symptom Solution Doesn't power on BACnet doesn't comminucate Binary Output isn't working Analog input isn't working Analog output isn't working RPI does not appear to be working Pressure sensing All lights are off (including 24 VAC LED) BACnet TX light is blinking green, RX is off BACnet does not share a common reference BACnet HLH LED is Red BACnet HLH LED is solid Yellow BACnet HLH LED is blinking Yellow Power selector switch is set incorrectly Corresponding LED is red Corresponding LED is blinking yellow Corresponding LED is solid yellow Corresponding LED is solid yellow Corresponding LED is red Corresponding LED is solid yellow Corresponding LED is blinking yellow Corresponding LED is red RPI is not turning on STA LED next to RPI port is Yellow STA LED next to T-Stat port is blinking Yellow STA LED next to T-Stat port is Red Reading frozen or does not change very much Reading inaccurate or unstable Check & Replace the fuse with a standard 10 amp automotive style fuse. Check for 24 VAC +-10%. Ensure all BACnet cables are connected between everything on the local BACnet network. Ensure all units that are connected via the local BACnet network share a common ground (Earth) connection and that A(+) and B(-) are connected correctly. The PMX is detecting traffic, but it is all corrupted. Check that the network length is below 1050 feet. All baud rates are the same, each device has a unique MAC and INSTANCE. Note: No more than 30 MS/TP devices per segment. The PMX is detecting traffic, but it is partially corrupted. Check that the network length is below 1050 feet. All baud rates are the same, each device has a unique MAC and INSTANCE. Ensure all BACnet cables are connected between everything on the local BACnet network. This says the PMX detects no devices whatsoever. The power selector switch needs to be fully down to switch 24 VAC, fully up to switch ground and in the middle to switch external power. The output is shorted, this will have to be resolved for normal operation. There is a BACnet override in place, that is forcing it off, this will have to be removed for the unit to control the output. There is a BACnet override in place, that is forcing it on, this will have to be removed for the unit to control the output. There is a BACnet override in place, this will have to be removed for the input to respond as expected (0-10 Input) The voltage to the input is exceeding 10 VDC. In addition, if the voltage is sufficiently high, it will cause corruption to the other Analog Inputs (Temperature Input) The temperature being read is over 250 ºF (120 ºC), check the attached temperature probe. Price temperature probes should read 10,000 (10k) ohms at 77F (25C). There is a BACnet override in place, this will have to be removed for the output to respond as expected There is a BACnet override in place forcing the output off, this will have to be removed for the output to respond as expected There is a short on the output, it will have to be fixed before the output will work as expected Check that the cable is plugged into both the T-Stat and the PMX The PMX is unable to detect the RPI, check the cable Fault detected, check the cable and the RPI Fault detected, check the cable and the RPI Check line to sensor pushed onto nipple and not pinched Check draft from nearby diffusers not blowing across or into sensor priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 25

28 MAINTENANCE BACnet Point List Object Name Units Range Description R/W AI1 Primary Room Pressure inh2o -0.1 to +0.1 Primary Room Pressure Reading R AI2 Secondary Room Pressure inh2o -0.1 to +0.1 Secondary Room Pressure Reading R AI3 Analog Input 3 Dynamic Dynamic Input can be CFM, Inches of Water, etc - See O&M Manual for detail. Input Menu. R AI4 Analog Input 4 Dynamic Dynamic Input can be CFM, Inches of Water, etc - See O&M Manual for detail. Input Menu. R AI5 Analog Input 5 Dynamic Dynamic Input can be CFM, Inches of Water, etc - See O&M Manual for detail. Input Menu. R AI6 Analog Input 6 Dynamic Dynamic Input can be CFM, Inches of Water, etc - See O&M Manual for detail. Input Menu. R AI7 Analog Input 7 Dynamic Dynamic Input can be CFM, Inches of Water, etc - See O&M Manual for detail. Input Menu. R AI8 Analog Input 8 Dynamic Dynamic Input can be CFM, Inches of Water, etc - See O&M Manual for detail. Input Menu. R AI9 Analog Input 9 Dynamic Dynamic Input can be CFM, Inches of Water, etc - See O&M Manual for detail. Input Menu. R AI10 Analog Input 10 Dynamic Dynamic Input can be CFM, Inches of Water, etc - See O&M Manual for detail. Input Menu. R BI1 Binary Input 1 Open/Closed Open/Closed Tyipcally: Door Switch R BI2 Binary Input 2 Contatcs Open/Closed Contatcs Open/Closed Binary Input can be tied to several signals. See O&M manual for detail. Input Menu. R AO1 Analog Output 1 Volts DC 0-10 VDC The Analog Output can be tied to several signals. See O&M manual for detail. Output Menu. AO2 Analog Output 2 Volts DC 0-10 VDC The Analog Output can be tied to several signals. See O&M manual for detail. Output Menu. BO1 Binary Output 1 On/Off On/Off The Binary Output can be tied to several signals. See O&M manual for detail. Output Menu. BO2 Binary Output 2 On/Off On/Off The Binary Output can be tied to several signals. See O&M manual for detail. Output Menu. R/W R/W R/W R/W AV2 AV3 AV5 AV6 Primary Room Low Pressure Alarm Primary Room High Pressure Alarm Secondary Room Low Pressure Alarm Secondary Room High Pressure Alarm inh2o (-0.1) to 0.1 Low pressure alarm trip point for the primary room (Positive or Negative depending on room type.) inh2o (-0.1) to 0.1 High pressure alarm trip point for the primary room (Positive or Negative depending on room type.) Requires room pressure sensor. inh2o (-0.1) to 0.1 Low pressure alarm trip point for the secondary room (Positive or Negative depending on room type.) inh2o (-0.1) to 0.1 High pressure alarm trip point for the secondary room (Positive or Negative depending on room type.) Requires room pressure sensor. AV7 Alarm Code Bitwise Numeric Not typically used R AV8 Caution Code Bitwise Numeric Not typically used R R R R R MI1 Keyswitch Position N/A 7 states 1 - Unknown Value 2 - No keyswitch 3 - Isolation 4 - (N/A) 5 - (N/A) 6 - (N/A) 7 - Setback MV1 Status Text 4 states Room Status: 1 - Normal 2 - Caution 3 - Alarm 4 - Setback MV2 Primary Isolation Mode Text 2 states Room Isolation Mode 1 - Positive 2 - Negative R R R 26 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

29 MAINTENANCE BACnet Point List Continued... Object Name Units Range Description R/W MV3 Secondary Isolation Mode Text 2 states Room Isolation Mode 1 - Positive 2 - Negative MV4 Alarm Status Text 23 states Alarm Status: 1 - No Alarm 2 - Emergency Button 3 - Network Override 4 - Contact Input 5 - Missing Primary Sensor 6 - Missing Secondary Sensor 7 - Incorrect Keyswitch 8 - Primary Room Low Pressure 9 - Primary Room High Pressure 10 - Secondary Room Low Pressure 11 - Secondary Room High Pressure 12 - Extended Door Open 13 - Low Voltage on Input 14 - Low Airflow 15 - Low Pressure on AI 16 - Low Air Changes 17 - High Voltage on Input 18 - High Airflow 19 - High Pressure on AI 20 - High Air Changes MV5 Caution Status Text 25 states Caution Status: 1 - No Caution 2 - Network Override 3 - Contact Input 4 - Door Open 5- Primary Room Low Pressure 6 - Primary Room High Pressure 7 - Secondary Room Low Pressure 8 - Secondary Room High Pressure 9 - Missing Primary Sensor 10 - Missing Secondary Sensor 11 - Primary Sensor Setpoint Range 12 - Secondary Sensor Setpoint Range 13 -Unknown Keyswitch 14 - Low Voltage on Input 15 - Low Airflow 16 - Low Pressure on AI 17 - Low Air Changes 18 - High Voltage on Input 19 - High Airflow 20 - High Pressure on AI 21 - High Air Changes R R R priceindustries.com ROOM PRESSURE MONITOR DELUXE - User Guide 27

30 NOTES 28 ROOM PRESSURE MONITOR DELUXE - Manual priceindustries.com

31 NOTES priceindustries.com ROOM PRESSURE MONITOR DELUXE - Manual 29

32 This document contains the most current product information as of this printing. For the most up-to-date product information, please go to priceindustries.com Price Industries Limited. All rights reserved.