The MS-5024UD/MS-5024UDE Fire Control Communicator

Transcription

1 The MS-5024UD/MS-5024UD ire Control Communicator Installation, Operation and Programming Manual 12 Clintonville Road, Northford, CT Document # /2/97 Rev: P/N 15140: CN ire Lite Alarms, Inc.

2 2

3 NPA Standards, UL Documents 5 Table of Contents 1.0 Product Description 7 igure 1-1: Optional DP-5024UD 7 igure 1-2: MS-5024UD Panel Controls and Indicators 9 igure 1-3: Controls and Indicators Circuits Digital Communicator Components 10 igure 1-4: XRM-24 Transformer Optional Devices Specifications Telephone Requirements and Warnings Installation General Backbox Mounting 15 igure 2-1: Cabinet Dimensions & Knockouts 16 igure 2-2: Backbox and Battery Box Operating Power 18 igure 2-3: Operating Power Connections 18 igure 2-4: Auxiliary Power Connections Input Circuits Output Circuits 20 igure 2-5: Typical Initiating Device Circuit Connect 20 igure 2-6: Notification Appliance Circuit Connections 21 igure 2-7: Aux Relay and Relay Driver Terminals UL Power-limited Wiring Requirements 23 igure 2-8: Typical Wiring for UL Power-limiting Digital Communicator 24 igure 2-9: Wiring Phone Jack Optional Boards 25 igure 2-10: ADM igure 2-11: RZA-5 25 igure 2-12: Wiring the RZA-5/ADM igure 2-13: Installing the Annunciator 26 igure 2-14: Remote Printer Connections 27 igure 2-15: RM-5 28 igure 2-16: CAC-5 Style D Converter Programming Instructions ntering Program Mode Switch unctions 31 igure 3-1: Control Panel Keypad Programming Options 31 Table 3-1: vent Codes, Primary C. S. Number 34 Table 3-2: vent Codes, Primary C. S. Number 34 Table 3-3: vent Codes, Secondary C. S. Number 36 Table 3-4: vent Codes, Secondary C. S. Number 37 igure 3-2: Verification Timing Diagram 38 3

4 Table of Contents 4.0 Operating Instructions Switches Displays 45 igure 4-1: Phone Connectors & LDs Operation Central Station Communications 50 Table 4-1: ormat Selection Addresses (16+42) 51 Table 4-2: ormat Selection Address xplanation 52 Table 4-3: Compatible UL Listed Receivers Servicing Walk Test Mode History Mode Troubleshoot Mode Lamp Test 59 igure 5-1: Handset/Speaker Connection Print Mode Slave Communicator Configuration 61 igure 6-1: Slave Communicator Connections Remote Site Upload/Download Downloading Program: General Security eatures Downloading Initiated at Control Panel Downloading Initiated at Service Terminal Uploading Initiated at Service Terminal 66 Appendix A: Battery Calculations 67 Appendix B: Programming Reference Sheets 70 Appendix C: Operation and unction Modes 76 4

5 This control panel has been designed to comply with standards set forth by the following regulatory agencies: Underwriters Laboratories Standard UL 864 NPA National ire Alarm Code for Local, Remote Station and Central Station ire Alarm System CAN/ULC - S527-M87 Standard for Control Units for ire Alarm Systems Before proceeding, the installer should be familiar with the following documents. NPA Standards: NPA National ire Alarm Code Central Statiion ire Alarm Systems (Automatic, Manual, and Waterflow) Protected Premises Unit Local Protective ire Alarm Systems (Automatic, Manual, Waterflow and Sprinkler Supervisory) Auxiliary Protective ire Alarm Systems (Automatic, Manual and Waterflow) Remote Station Protective ire Alarm Systems (Automatic, Manual and Waterflow) Proprietary Protective ire Alarm Systems (Automatic, Manual and Waterflow) Underwriters Laboratories Documents: UL 38 Manually Actuated Signaling Boxes UL 217 Smoke Detectors, Single and Multiple Station UL 228 Door Closers Holders for ire Protective Signaling Systems UL 268 Smoke Detectors for ire Protective Signaling Systems UL 268A Smoke Detectors for Duct Applications UL 346 Waterflow Indicators for ire Protective Signaling Systems UL 464 Audible Signaling Appliances UL 521 Heat Detectors for ire Protective Signaling Systems UL 864 Standard for Control Units for ire Protective Signaling Systems UL 1481 Power Supplies for ire Protective Signaling Systems UL 1638 Visual Signaling Appliances CAN/ULC - S524-M91 Standard for Installation of ire Alarm Systems Other: NC Article 300 Wiring Methods NC Article 760 ire Protective Signaling Systems Applicable Local and State Building Codes Requirements of the Local Authority Having Jurisdiction ire-lite Documents ire-lite Device Compatibility Document Document #

6 Power-limited Power-limited Power-limited Power-limited Power-limited Power-limited 6

7 1.0 Product Description The MS-5024UD is a combination control panel and digital communicator all on one circuit board. It is a five-zone panel which uses conventional input devices. The panel accepts waterflow devices, two-wire smoke detectors, fourwire smoke detectors, pull stations and other normally open contact devices. Outputs include two Notification Appliance Circuits, alarm and trouble relays, supervisory and communicator failure relay drivers. The integral communicator transmits system status (alarms, troubles, AC loss, etc.) to UL-listed Central Stations via the public switched telephone network. The control panel has a built in programmer and may also serve as a slave communicator to a host panel. It also supervises all wiring, AC voltage, telephone line input voltage and battery level. The control panel may be programmed or interrogated off site via the public switched telephone network. Any IBM compatible personal computer with DOS 4.01 or greater plus Windows 3.1 or greater, with a 1200 Baud Hayes compatible modem and ire Lite Upload/Download software P/N PK-5024UD, may serve as a Service Terminal. This allows download of the entire program or upload of the entire program, history file, walktest data, current status and system voltages. The MS-5024UD offers the same features as the MS-5024UD but allows connection to 220/ 240 VAC input. 1.1 Product eatures Selectable as ire Panel, ire Panel/Communicator, or Slave Communicator Programmable Zone ID: 2 Wire Smoke; Pull Station; Normally Open Contact; Supervisory; Supervisory- Auto Silence; Waterflow-Silenceable; Waterflow- Non- Silenceable One Style D (Class A) Zone our Style B (Class B) Zones 3.6 amps Usable Power xpandable to 5.6 amps 5 Zone Relay Option Module (RM-5) CAC-5 Style D Class A Zone Converter Module Two NPA Style Y or Z (Class B or A) Notification Appliance (bell) Circuits Built-in Programmer Built-in Voltmeter Telephone Line Active LD Indicators Communication Confirmation (Kissoff) LD Disable report by event Programmable vent Codes 24 Volt Operation Real Time Clock and Calendar Trouble Reminder Alarm Verification RZA-5 Remote Annunciator (requires ADM-24 Annunciator Driver Module) Small Size 15" x 14.5" x 2.75" History ile with 32 vent Storage Silence Inhibit per Notification Appliance Circuit Auto-Silence per Notification Appliance Circuit Touchtone/Rotary Dialing Programmable Make/Break Ratio useless Printer Interface Module (PRT-24) igure 1-1: Optional DP-5024UD Print Real-time System Status Print History & Walk Test iles, Program Contents, & Troubleshoot mode voltages PK-5024UD Upload/Download Software Kit. Number of dial attempts (5 min, 10 max) Programmable Channel ID (slave) Programmable Zone Delay (waterflow only) orm-c Alarm and Trouble Relays Supervisory, Communication ail Relay Drivers Low AC Voltage Sense One Man Walk Test Optional Dead ront cover (DP-5024UD) Note: Unless otherwise specified, MS-5024UD shall be used in this manual to refer to both the MS-5024UD and MS-5024UD ire Control Communicators. 7

8 Notification Appliance Circuits Alarm & Trouble Relays 5 Input Zones Primary & Secondary Phone Lines Annunciator Driver Module Interface Connector our Character 7-Segment LD Display Keypad PROM (U23) 1 Relay Module Interface Connector Optional Transformer Piezo 85dB Holds up to 7AH Batteries Up to 60 Hrs. of Standby Printer Interface Module Connector Note: 1 Software for the ire Control Communicator is located in a PROM inserted in the IC socket labeled U23. The MS-5024UD and MS-5024UD each contain unique software. or specific panel software information refer to: MS-5024UD() ield Software Change Procedure Document #50125 igure 1-2: MS-5024UD Panel 8

9 1.2 Controls and Indicators ront Panel Switches RST Digits 0-9 SILNC A MOD B Up Arrow C Down Arrow D 1st VNT NTR/STOR Displays Alarm - red LD Trouble - yellow LD Supervisory - yellow LD AC Power - green LD our, Seven Segment Displays - red Primary Phone Line Active - red LD Secondary Phone Line Active - red LD 'Kissoff' Signal from Central Station - green LD Silence - yellow LD Modem - green LD igure 1-3: Controls and Indicators 1.3 Circuits Local Sounder - A piezo sounder provides separate and distinct sounds for alarm, trouble and supervisory conditions. Input Circuits ive input circuits provide Style B configuration with one circuit also configurable for Style D. Input circuits may be used as standard fire control panel zones or slave communicator input channels. Initiating Device Circuit 1 (Style B) accepts Normally Open contact devices and 2- wire smoke detectors. Initiating Device Circuit 2 (Style B) accepts Normally Open contact devices and 2- wire smoke detectors. Initiating Device Circuit 3 (Style B/D) accepts Normally Open contact devices, 2- wire smoke detectors and waterflow devices. Initiating Device Circuit 4 (Style B) accepts Normally Open contact devices and 2- wire smoke detectors. Initiating Device Circuit 5 (Style B) accepts Normally Open contact devices and 2- wire smoke detectors. Output Circuits 24 Volt Resettable Power Output 24 Volt Non-Resettable Power Output Primary Telephone Line Secondary Telephone Line 24 Volt Battery Charger Printer Port Notification Appliance Circuits - Two Notification Appliance Circuits configurable for Style Y (Class B) or Style Z (Class A) with various programmable features. Relays - Two dry orm-c relay contacts for System Alarm and System Trouble are provided. Contacts are rated 2 amps at 30 VDC and 0.5 amps at 30 VAC resistive. Relay Drivers - Two relay drive outputs for supervisory and communication failure are available. 9

10 1.4 Digital Communicator Two modular phone jacks allow easy connection to telephone lines. Modular jacks are labeled PH1 and PH2 for the Primary and Secondary phone lines. Telephone line active red LDs are provided as well as a green 'Kissoff' LD. The integral digital communicator provides the following functions: Line Seizure - takes control of the phone lines disconnecting any premises phones. Off/On Hook - perform on and off-hook status to the phone lines. Listen for dial tone hertz tone typical in most networks. Dialing the Central Station(s) number - default is Touch-Tone, programmable to rotary. or tone burst or touchtone type formats: Discern proper 'Ack' and 'Kiss-off' tone(s) - The frequency and time duration of the tone(s) varies with the transmission format. The control panel will adjust accordingly. Communicate in the following formats: 12 Tone Burst Types: 20 pps (3+1, 4+1, 4+2, 3+1 xp., 4+1 xp., 4+2 xp.) 2 Touchtone Types: Ademco xpress Ademco xpress See Table 4-3 for list of compatible receivers. 1.5 Components Main Circuit Board The main circuit board contains the system's CPU, power supply, other primary components and wiring interface connectors. Optional modules plug in and are mounted to the main circuit board. The main circuit board is delivered pre-mounted in the cabinet. Cabinet The cabinet is red with an attractive navy blue front overlay. The backbox measures 15" x 14.5" x 2.75" and provides space for two batteries (up to 7 Amp Hours). Also available is an optional dress panel, DP-5024UD, which mounts inside the cabinet. Standard Transformer Assembly One 100VA transformer is provided standard with the panel (3.6 amps max.). An optional 100VA transformer, XRM-24 (XRM-24 for MS-5024UD), is available to provide maximum accessory power (6.6 amps max.). Batteries The cabinet provides space for 7 Amp Hour batteries (for 12 Amp Hour to 17 Amp Hour batteries use the listed BB-17 battery box). Batteries must be ordered separately. Optional XRM-24() 10 igure 1-4: XRM-24() Transformer

11 1.6 Optional Devices RM-5 ive-zone Relay Module The RM-5 option module provides 5 orm-c relays which track zones 1 through 5. The module mounts to connector J7 on the lower right side of the main board. See igures 1-2 and CAC-5 The CAC-5 Class A Converter module converts the Style B (Class B) Initiating Circuits to Style D (Class A). The CAC-5 mounts to terminal block TB2 located in the upper center of the main circuit board. The removable terminal block on the CAC-5 module provides for ease of wiring (refer to igure 2-16). ADM-24 The ADM-24 Annunciator Driver Module supports the RZA-5 Remote Annunciator module. Annunciator wiring is supervised for open circuits by this module. The Annunciator Driver Module mounts to connector J3 in the upper right corner of the main board. See igure 1-2 and 2-8. Remote Annunciator The RZA-5 Remote Annunciator mounts on a standard single-gang box, and provides LD indication of the following: Alarm Zone 1 (red) Alarm Zone 2 (red) Alarm Zone 3 (red) Alarm Zone 4 (red) Alarm Zone 5 (red) System Trouble (yellow) A Local Trouble Sounder and Tone Silence Switch are also provided. All LDs and their wiring are supervised for open conditions. Any open condition will cause the System Trouble LD to illuminate. Slide in paper labels permit an easy change of zone information. See igure Note: The Remote Annunciator requires the use of the ADM-24 Annunciator Driver Module. Printer Interface Module-PRT-24 The Printer Interface Module may be used to connect a printer to the control panel for the purpose of printing a history report, Walk Test file, troubleshoot report, program entries or current system status. Printers require separate external primary power. Connect the PRT-24 module (with cable) to the serial IA-232 port on the printer. The module mounts to the J2 connector on the main circuit board. Note: An DP listed printer must be used if printer will be permanently attached. See igure Dress Panel A red dead-front dress panel (DP-5024UD) is available as an option (required for Canadian installations). The dress panel restricts access to the system wiring while allowing access to the membrane switch panel. See igure 1-1. Battery Box The BB-17 battery box may be used to house two 12 Amp Hour or 17 Amp Hour batteries. The battery box mounts directly below the main circuit board in the cabinet (refer to igure 2-2). The BB-17 is red and is provided with knockouts. 11

12 Program Kit - PK-5024UD This kit includes one 3½" diskette plus Instruction Manual P/N When the software is loaded into an IBM compatible computer, it creates an off-line Service Terminal that allows any MS-5024UD panel to be uploaded or downloaded over standard telephone lines. 1.7 Specifications AC Power - TB1 MS-5024UD: 120 VAC, 60 Hz, 2.3 amps MS-5024UD: 220/240 VAC, 50 Hz, 1.2 amps Wire size: minimum #14 AWG with 600V insulation Battery (lead acid only) - J1 Maximum Charging Circuit: Normal lat Charge amp Maximum Charger Capacity: 17 Amp Hour battery. (MS-5024UD cabinet holds max. 7 Amp Hour batttery. Larger batteries require ire-lite #BB-17 or other UL listed battery cabinet). Initiating Device Circuits TB2 Detector Zones 1, 2, 3, 4, 5 Power-Limited Circuitry Operation: All zones (NPA Style B), Zone 3 (NPA Style B or D). Use CAC-5 module for Style D operations Normal Operating Voltage: 24 VDC (ripple = 100 mv max) Alarm Current: 26 ma Short Circuit Current: 42 ma max. Maximum Loop Resistance: 100 ohms nd-of-line Resistor: 4.7K, 1/2-Watt (part # UL listed) Detector Loop Current is sufficient to ensure operation of one alarmed detector per zone. Standby Current: 7.26 ma (includes LR and 2 ma maximum detector current) Smoke Detector Identifier A Refer to ire-lite Compatibility Chart for listed compatible devices. Notification Appliance Circuits - TB5 & TB6 Non-regulated special purpose power, Styles Y and Z supported Power-limited circuitry Operating Voltage Nominal 24 volts Current for all external devices: 3.0 amps expandable to 5.6 amps Current Limit: PTC Max. signaling current/circuit: 2.5 amps nd-of-line resistor: 4.7K, 1/2-Watt (part # UL listed) for NACs. Refer to ire-lite Compatibility Chart for listed compatible devices. Alarm and Trouble Relays - TB3 Contact rating: VDC (resistive), VAC (resistive) Alarm and Trouble: orm-c Power-limited Circuitry (see igure 2-7 note for power-limited wiring application). Auxiliary Outputs TB4, Terminals 5-6 TB4-5 Supervisory Relay Driver. Normally high, active low. Sinks up to 40 ma. TB4-6 Communication ailure. Normally high, active low. Sinks up to 40 ma. Power-limited Circuitry. our-wire Smoke Detector Power - TB-4 Terminals 3 (+) & 4 (-) Max. ripple voltage: 10 mv RMS Operating Voltage nominal 24 volts Up to 300 ma is available for powering 4-wire smoke detectors. Power Limited Circuitry. Recommended maximum Standby current is 50 ma (see Battery Calculations in Appendix A). Refer to ire-lite Compatibility Chart for compatible listed devices. 12

13 Non-resettable Regulated 24V Power - TB-4 Terminals 1 (+) & 2 (-) Max. ripple voltage: 10 mv RMS Operating Voltage nominal 24 volts Total DC current available from this output is up to 300 ma. Power Limited Circuitry. Recommended maximum Standby current is 150 ma (see Battery Calculations in Appendix A). Refer to ire-lite Compatibility Chart for compatible listed devices. Notes: 1) or power supply calculations, refer to Appendix A. 2) Total current for non-resettable power, four-wire smoke power, and two Notification Appliance Circuits must not exceed 5.6 amps. Total external system current in excess of 3.6 amps requires the XRM-24 (XRM-24 for 220/240 VAC applications) Transformer and 12 Amp Hour or 17 Amp Hour batteries. 1.8 Telephone Requirements and Warnings Telephone Circuitry: Ringer quivalence Number (RN) = 1.3B AC Impedance 10.0 Mega Ohm Complies with CC Part 68 Mates with RJ31X Male Connector Supervision Threshold: less than 4.0 volts for 2 minutes The RN is used to determine the quantity of devices which may be connected to the telephone line. xcessive RN's on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the RN's should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RN's, contact the telephone company to determine the maximum RN for the calling area Digital Communicator: Before connecting the control panel to the public switched telephone network, the installation of two RJ31X jacks is necessary. The following information is provided if required by the local telephone company : Manufacturer : ire Lite Alarms, Inc. 12 Clintonville Rd. Northford, CT Product Model Number: MS-5024UD CC Registration Number: 1W6USA AL- Ringer quivalence 1.3B Telephone Company Rights and Warnings: The telephone company under certain circumstances may temporarily discontinue services and/or make changes in its facilities, services, equipment or procedures which may affect the operation of this control panel. However, the telephone company is required to give advance notice of such changes or interruptions. If the control panel causes harm to the telephone network, the telephone company reserves the right to temporarily discontinue service. Advance notification will be provided except in cases when advance notice is not practical. In such cases, notification will be provided as soon as possible. The opportunity will be given to correct any problems and to file a complaint. DO NOT CONNCT THIS PRODUCT TO COIN TLPHON, GROUND START, OR PARTY LIN SRVICS. 13

14 When the control panel activates, premise phones will be disconnected. Two separate phone lines are required. Do not connect both telephone interfaces to the same telephone line. The control panel must be connected to the public switched telephone network upstream of any private telephone system at the protected premises. An CC compliant telephone cord must be used with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible RJ31X male modular plug which is Part 68 compliant or Canadian Applications The following is excerpted from CP-01 Issue 5: "NOTIC: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate." "The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100." DOC Compliance - "This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications." DOC Registration Number: A Load Number: 2 14

15 2.1 General Mounting Options The cabinet may be either semi-flush or surface mounted. The door is removable during the installation period by opening and lifting off the hinges. 2.0 Installation The cabinet mounts using two key slots and two additional 0.250" diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage. Mount the cabinet in a clean, dry, vibration-free area where extreme temperatures are not encountered. The area should be readily accessible with sufficient room to easily install and maintain the panel. Locate the top of the cabinet approximately five feet above the floor with the hinge mounting on the left. Determine the number of conductors required for the devices to be installed. Sufficient knockouts are provided for wiring convenience. Select the appropriate knockout(s) and pull the required conductors into the box. Note that there are no knockouts on the left (hinged) side of the cabinet. All wiring should be in accordance with the National and/or Local codes for fire alarm systems. 2.2 Backbox Mounting Open the door and lift the door off the pin hinges. Remove the main PC board assembly by unscrewing the four screws in the corners of the board. Two standoffs support the board in the center. Set the board aside in a safe, clean place. Avoid static discharge which may damage the board. Mark and predrill holes for the top two keyhole mounting bolts using the dimensions shown. Install two upper fasteners in the wall with the screw heads protruding. Using the upper 'keyholes', mount the backbox over the two screws. Mark and drill the lower two holes. Mount backbox, install remaining fasteners and tighten. When the location is dry and free of construction dust, reinstall the main PC board. 15

16 Top Right Side Bottom TR-1-R Trim Ring Draw wires through the respective knockout locations. igure 2-1: Cabinet Dimensions & Knockout Locations 16

17 Notes: 1) Mount the ire Control Communicator cabinet to the wall. 2) Remove knockouts on bottom of ACP cabinet and top of BB-17. 3) Using conduit, hang BB-17 from the ire Control Communicator cabinet making sure there is at least 1/2" of clearance between the two cabinets. 4) Anchor BB17- to wall. igure 2-2: Backbox and Battery Box 17

18 2.3 Operating Power CAUTION: Several different sources of power can be connected to this panel. Disconnect all sources of power before servicing. The panel and associated equipment may be damaged by removing and/or inserting cards, modules, or interconnecting cables while this unit is energized. Primary Power Source (AC) and arth Ground Connections AC power connections are made inside the control panel cabinet. The primary power source for the MS-5024UD is 120 VAC, 60 HZ, 2.3 amps, and for the MS-5024UD is 220/240 VAC, 50 Hz, 1.2 amps. Run a pair of wires (with ground conductor) from the protected premises main breaker box to TB1 of the main circuit board. As per the National lectric Code, use 14 AWG (1.6 mm O.D.) or heavier gauge wire with 600V insulation. No other equipment may be connected to this circuit. In addition, this circuit must be provided with overcurrent protection and may not contain any power disconnect devices. A separate arth Ground connection must be made to ensure proper panel operation and lightning and transient protection. Connect the arth Ground wire (minimum 14 AWG) to one of the transformer mounting studs. Note: Do not use conduit for the arth Ground connection since this does not provide reliable protection. Secondary Power Source (Batteries) Observe polarity when connecting the battery. Connect the battery cable to J1 on the main circuit board using the plug-in connector provided. The battery charger is current limited and capable of recharging sealed lead acid type batteries. The charger shuts off when the system is in alarm. See Appendix A for calculation of the correct battery rating. CAUTION: Battery contains sulfuric acid which can cause severe burns to the skin and eyes, and can destroy fabrics. If contact is made with sulfuric acid, immediately flush the skin or eyes with water for 15 minutes and seek immediate medical attention. Connect arth Ground Wire igure 2-3: Operating Power Connections 18

19 DC Power Output Connections All DC power outputs are power-limited Non-resettable Power (300 ma) 24 VDC filtered, regulated, nonresettable power can be obtained from TB4 Terminals 1 (+) and 2 (-). 4-Wire Smoke Detector Power (300 ma) 24 VDC filtered, regulated, resettable power for 4-wire smoke detectors can be obtained from TB4 Terminals 3 (+) and 4 (-). igure 2-4: Auxiliary Power Connections 2.4 Input Circuits The control panel has five zone input circuits. The maximum loop resistance limit for each is 100 ohms. All field wiring of each zone is supervised for opens and ground faults. Both conditions are visually and audibly annunciated as well as communicated to a Central Station. ach zone is a Style B Initiating Device Circuit (IDC) designed to accept any Normally Open contact device and conventional 2-wire, 24 volt smoke detectors. ach zone is power limited to 7.26 ma in standby and 42 ma in alarm. Zone 3 may also be configured as a Style D Initiating Device Circuit. Note: All five initiating zones may be converted to Style D (Class A) by using a CAC- 5 Class A Converter module (refer to igure 2-16). Zones 1-5 may be programmed as shown below. The factory default is 2-wire smoke detector for all zones. 2-wire Smoke Detector (factory default) Pull Station Normally Open Contact Device(s) Supervisory Supervisory, Auto-Resettable Zone 3 may also be programmed as: Waterflow Silenceable Waterflow, Non-Silenceable Note: A maximum of five waterflow devices may be used on zone 3 per NPA 72. our-wire smoke detectors may be connected to any zone. Resettable power is provided via terminals TB4, 3 and 4. 19

20 It is allowable to mix an assortment of device types (ie, smoke detectors, heat detectors, pull stations) on any zone. However, this is not recommended since specific and detailed reports will not be possible. or example, the report of general fire alarm versus pull station fire alarm or smoke detector fire alarm. Refer to the ire-lite Device Compatibility Document for a list of compatible smoke detectors. Style B Initiating Device Circuit (Supervised and power-limited). 4.7KΩ, 1/2-Watt Part# UL listed. UL listed compatible 2-wire smoke detector Style D Initiating Device Circuit (Supervised and power-limited).. UL listed compatible 2-wire smoke detector Manual Pull Station Manual Pull Station Heat Detector Heat Detector Dummy load all unused circuits with 4.7K LR P/N: across B+ and B- B+ B- B+ B- B+ A+ A- B- B+ B- B+ B- TB2 MS-5024UD igure 2-5: Typical Initiating Device Circuit Connections 20

21 2.5 Output Circuits Telephone Circuits Provision to connect to two independent telephone lines is available via two telephone jacks labeled PH1 (Primary) and PH2 (Secondary). Telephone line control/ command is possible via double line seizure as well as usage of an RJ31X style interconnection. See igure 2-8. Notification Appliance Circuits The MS-5024UD provides two Notification Appliance Circuits (Style Y or Z). ach circuit is capable of 2.5 amps of current. Total current drawn from these as well as other DC power outputs cannot exceed 3.6 amps with the standard transformer, 5.6 amps if an optional XRM-24 (XRM-24 for the MS-5024UD) transformer is installed. Circuits are supervised and power-limited. Refer to the ire-lite Device Compatibility Document for a listing of compatible Notification Appliances. Style Z Notification Appliance Circuit (Supervised and power-limited) Polarized Bell Style Y Notification Appliance Circuit (Supervised and power-limited). 4.7KΩ, 1/2- Watt Part# UL listed. Polarized Bell Polarized Strobe Polarized Horn Polarized Horn Polarized Horn Note: Notification Appliance Circuit polarity shown in alarm state Dummy Load all unused Circuits (Part# 71245) igure 2-6: Notification Appliance Circuit Connections Both Notification Appliance Circuits may be programmed as follows: Silenceable Non Silenceable nabled/disabled Silence Inhibited Auto Silence, 5 to 30 minutes Coded (March Time, Temporal, California) 21

22 Standard Relays The control panel provides a set of orm-c alarm and a set of orm-c trouble contacts rated for VDC (resistive). Relay Drivers Relay driver outputs are provided for Supervisory and Communicator ailure. These outputs can be used to drive UL-864 listed remote relays such as the MR-101C and MR-201C.. The control panel's open collector outputs on TB4, terminals 5 and 6 can be used to activate UL-864 listed relays. Outputs are rated for 40 ma. The normal condition for each output is as shown below: TB4-5 Supervisory TB4-6 Communications ailure Off (de-energized) Off (de-energized) Relays must be placed inside the cabinet or in a UL-864 recognized enclosure. Wiring from the control panel's terminals on TB4 to the relays must be less than 3 feet in length and enclosed in conduit. Wiring from the relay outputs must remain in the same room as the location of the enclosure and be enclosed in conduit. Relay Connections Relay Driver Connections Relay energized LD Alarm Trouble NO NC C NC NO C DPDT Contacts VAC All wiring to relay must be in same room as panel and in conduit. Relay energized LD Connections must be in same room as panel. DPDT Contacts VAC Note: The alarm and trouble orm- C dry contact relays must be powerlimited circuits. Any orm-c dry contact relay that may be used must be wired from TB4 or a UL listed power-limited power supply. *Note: The MR-101C and MR-201C include an enclosure. igure 2-7: Aux Relay and Relay Driver Terminals 22

23 2.6 UL Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25" away from any nonpower-limited circuit wiring. urthermore, all power-limited and nonpowerlimited circuit wiring must enter and exit the cabinet through different knockouts and/or conduits. A typical wiring diagram for the MS-5024UD is shown below. Refer to igure 2-15 for additional information on wiring the RM-5 Relay Module. Power-limited Circuits Power-limited Circuit Nonpower-limited Circuit AC Power igure 2-8: Typical Wiring Diagram for UL Power-limited Requirements 23

24 2.7 Digital Communicator Two independent telephone lines can be connected to the control panel. Telephone line control/command is made possible via double line seizure as well as usage of an RJ31X style interconnection. Note: It is critical that the panel's digital communicator be located as the first device on the incoming telephone circuit to properly function. The control panel's digital communicator is built into the main board. Connection and wiring of two phone lines is required as shown below: (Primary Lines) Incoming Telco Phone Lines Tip Ring Green Wire Red Wire Ring To premise phones Tip Green Wire Tip Red Wire Ring (Secondary Lines) Incoming Telco Phone Lines Ring To premise phones Tip foot Cables MCBL-7 (order separately) igure 2-9 : Wiring Phone Jacks 24

25 2.8 Optional Boards ADM-24 Annunciator Driver Module The Annunciator Driver Module supports the RZA-5 Remote Annunciator. Annunciator wiring is supervised for open conditions by this module. The Annunciator Driver Module mounts to J3 in the upper right corner of the main board. Connector located on back of board Main Board igure 2-10: ADM-24 Standoff ADM-24 The RZA-5 Remote Annunciator mounts on a standard single-gang box, and provides LD indication of the following: Alarm Zone 1 (red) Alarm Zone 2 (red) Alarm Zone 3 (red) Alarm Zone 4 (red) Alarm Zone 5 (red) System Trouble (yellow) The remote annunciator provides individual zone alarm LDs, a system trouble LD, a piezo sounder and a remote sounder shut off switch. A Local Trouble Sounder and Silence Switch are also provided. All LDs and their wiring are supervised for open conditions. Any open condition will cause the System Trouble LD to illuminate. NOT: The Remote Annunciator requires the use of an ADM-24 Annunciator Driver Module. igure 2-11: RZA-5 25

26 +24V ADM-24 Note: Make wiring connections with system power off. Maximum wire impedance is 100 ohms per wiring connection. RZA-5 igure 2-12: Wiring the RZA-5/ADM-24 screw # 6-32 x 1.00" LG igure 2-13: Installing the Annunciator (Single Gang Box) 26

27 Printer Interface Module A remote printer may be permanently or temporarily connected to provide a hardcopy printout of normal current system status and activity, program entries, history file, troubleshoot mode voltages, and walk-test data. The Printer Interface Module Part Number PRT-24 provides an IA-232 conversion to adapt to most 40 and 80 column printers. CAUTION: DO NOT connect a printer to the ire Alarm Control Communicator if a ground fault exists on the panel. Circuit damage may result. Installation Remote printers require separate external primary power. Also required is the PRT- 24 which includes the Printer Interface Module and a 6 foot interface cable prewired to a DB25 connector. Connect the interface cable to the PRT-24 as shown in igure Insert the two supplied standoffs into mounting holes near the J2 connector on the main board. Connect the Printer Interface board to J2 on the main circuit board, press onto standoffs, and connect the attached cable to the serial IA-232 port on the printer. The printer may be placed a maximum of 50 feet from the panel. Note that a ground fault may occur on the control panel when this connection is made. or this reason, it is important that there be no preexisting ground fault on the panel. or permanent printer connection, a ground fault is not allowed. Printer Configuration The PRT-24 is required. Also refer to the documentation supplied with your printer. Set the printer s options as listed in the table below. Typical Printer Settings Under the MNU area: COMMUNIC. STUP: DATA BITS: 7 PARITY: VN STOP BIT: 1 STOP BAUD RAT: 2400 J1 located on back of PRT-24 board PRT-24 connection to main board DB-25P ront View igure 2-14: Remote Printer Connections 27

28 Power Limited RM-5 ive-zone Relay Module The RM-5 option module provides 5 orm-c relays which track zones 1 through 5. The module mounts to connector J7 on the lower right side of the main board as shown in igure Nonpower-limited and power-limited wiring must have a minimum distance of 0.25" wire to wire. If this module is used to drive nonpower-limited and power-limited circuits, follow the following instructions: 1) Skip a set of dry contacts to maintain the 0.25" required space between powerlimited and nonpower-limited circuits. The wiring of this module must follow the requirements as specified above. OR 2) If this module is needed to drive power-limited and nonpower-limited relays that are next to each other, one relay must be used as an open circuit and the other as a closed circuit as shown in the figure below. Connector located on back of board RM-5 Note: If relays are used as powerlimited circuits, paste supplied label to terminal block as indicated below. Main Board Power-limited Circuit Standoffs Power-limited Circuit Power-limited Circuit No connection No connection Nonpower-limited Circuit Note: Nonpower-limited Circuit Zone Relay Contact Ratings Max. Switched Power: 150 W or 1250 VA Max. Switched Current: 5 Amps UL Rating: 5 30 VDC or 125 VAC, Resistive Contact Material: Silver Alloy igure 2-15: RM-5 28

29 CAC-5 The CAC-5 Class A Converter module converts the Style B (Class B) Initiating Circuits to Style D (Class A). The CAC-5 mounts to terminal block TB2 located in the upper center of the main circuit board (refer to igure 2-16). The removable terminal block on the CAC-5 module provides for ease of wiring. UL listed compatible 2-wire smoke detector Waterflow switch Manual Pull Station Waterflow switch Heat Detector Waterflow switch Insert two supplied standoffs into CAC- 5 circuit board, remove protective paper from self adhesive base of standoff, install circuit board into TB2 of the MS- 5024UD and press to adhere standoffs to cabinet. Dummy load all unused circuits with 4.7K LR P/N: across B+ and B- CAC-5 Module MS-5024UD Main Board Note: 1) Circuits 1 through 5 can accommodate 2-wire smoke detectors, plus any N.O. contact device such as heat detectors or manual pull stations. 2) Only circuit 3 accommodates the non-silenceable waterflow function. igure 2-16: CAC-5 Style D Converter 29

30 3.0 Programming Instructions Programming Mode This section describes programming the panel from the onboard keyboard. Section 7.0 describes remote site upload/download which includes programming the control panel off premises. Programming of the control panel is possible at any time except when an alarm condition is present or during a fire drill. The control panel has been designed for many different types of applications. After examining your specific application, review the programming options and choose the entries best suited for your system. The control panel has a built-in intelligent programmer. All programming selections are stored in nonvolatile lectrically-rasable Programmable Read-Only Memory (PROM). This ensures that the control panel will remember all entries made in programming mode even if both AC and battery power are removed. Invalid entries cause a 'beep' from the onboard piezo sounder. The user must program the primary and secondary phone numbers, account numbers and 24 hour test report times for each Central Station account and the current time and date. The control panel comes with factory chosen options/features already programmed. Other options/features may be programmed if desired. If all factory default settings are acceptable, programming is complete. 3.1 ntering Program Mode To enter the Program Mode, press the MOD key once, (the display will go blank) you then have ten seconds to start entering the code (7764) spells PROG on a Touch-Tone phone If an incorrect key is entered, reenter the proper 4-digit code before pressing the [NTR/STOR] key 7 77 _ Note that as you enter information into the control panel, the digits will scroll across the display from right to left You are allowed a pause of up to 10 seconds in between each number while entering the code. After pressing the [NTR/STOR] key, the control panel will be in Program Mode and display 00_. You are allowed up to ten minutes of idle time at this point before starting your programming, otherwise the control panel will go back to Normal Mode. You also have a maximum of 10 minutes between any key stroke. All entries made prior to the 10 minute time-out are valid and are stored. Once in Programming Mode, the control panel will: Blink the trouble LD. Activate the trouble relay. Disable the Notification Appliance Circuit(s). Disable the alarm relay. The display shows: 00_ Ignore all other keys other than those mentioned in this section. Continue to communicate any events not previously acknowledged at a Central Station prior to entering Programming Mode. 30

31 Note: Location 56 is factory defaulted to = 0, Control Panel only. This keeps the communicator off until location 56 is changed to: 1= slave communicator or 2 = panel/communicator. Once location 56 is set to 1 or 2 and a valid phone number is entered, entry into the program mode will cause transmission of the "System off Normal" report. Throughout programming mode, the first three locations on the left of the display represent the memory address which can go from 00 to 374 (Alpha characters are not used). The last location (farthest right) represents the contents of the memory address. The first address displayed is shown below: 00_ (address)(data) 3.2 Switch unctions The unction of each switch in program mode is shown below: No function in Program Mode Address entry keys are 0 to 9 Data entry keys are 0 to 9 and A to { - Select operating mode - Increment memory address - Decrement memory address - Once = irst memory address Twice = type any address - Save data, go to next address igure 3-1: Control Panel Keypad 3.3 Programming Options Primary Central Station phone number. (00-15) The first sixteen addresses, 00-15, are factory set to '' (from 00_ to 15_). Programming is typically done as follows: If your phone # is , type 4, the display will read 00_4, press [NTR/STOR] to save the entry to memory and increment to the next address 01_. nter the remaining numbers in their respective addresses as shown below:

32 Valid entries for both the primary and secondary phone numbers are 0 - with the numeric digits as dialed numbers and hex digits representing the following functions: A= * on a Touchtone phone keypad B= # on a Touchtone phone keypad C= look for secondary dial tone for up to 2 seconds (then, dial anyway) D= 3-second pause = 5-second pause = end of phone number (Note: must be entered) Primary Central Station Number Communication ormat. (16) One location is needed to select the Communication ormat to the primary phone number. Address 16 is used for this purpose. The default (factory setting) for this address is 16_A, which is 4+2 Standard, 1800 Hz 'Carrier', 2300 Hz 'ack'. You may enter 0 through D in place of the default, then press [NTR/STOR]. Choose from the list of formats below: 0: 4+1 Ademco xpress Standard, DTM, 1400/2300 ACK 1: 4+2 Ademco xpress Standard, DTM, 1400/2300 ACK 2: 3+1 Standard 1800 Hz Carrier, 2300 Hz ACK 3: 3+1 xpanded 1800 Hz Carrier, 2300 Hz ACK 4: 3+1 Standard 1900 Hz Carrier, 1400 Hz ACK 5: 3+1 xpanded 1900 Hz Carrier, 1400 Hz ACK 6: 4+1 Standard 1800 Hz Carrier, 2300 Hz ACK 7: 4+1 xpanded 1800 Hz Carrier, 2300 Hz ACK 8: 4+1 Standard 1900 Hz Carrier, 1400 Hz ACK 9: 4+1 xpanded 1900 Hz Carrier, 1400 Hz ACK A: 4+2 Standard 1800 Hz Carrier, 2300 Hz ACK B: 4+2 xpanded 1800 Hz Carrier, 2300 Hz ACK C: 4+2 Standard 1900 Hz Carrier, 1400 Hz ACK D: 4+2 xpanded 1900 Hz Carrier, 1400 Hz ACK : Not Used : Not Used Note: Consult your Central Station for proper selection or consult our factory representatives. or any format chosen, the control panel automatically programs all of the event codes. See Tables 3-1, 3-2, 3-3, and

33 3+1, 4+1 xpress, 4+1 Standard and xpanded, 4+2 xpanded ormats If '0, 2, 3, 4, 5, 6, 7, 8, 9, B or D' are entered for address 16, the following data is automatically programmed for the Primary Central Station phone number event codes. nter '0' for the setting to disable the report. Address Description Setting 127 Primary # Zone 1 Alarm Code Primary # Zone 2 Alarm Code Primary # Zone 3 Alarm Code Primary # Zone 4 Alarm Code Primary # Zone 5 Alarm Code Primary # Zone 1 Disabled Code 133 Primary # Zone 2 Disabled Code 134 Primary # Zone 3 Disabled Code 135 Primary # Zone 4 Disabled Code 136 Primary # Zone 5 Disabled Code 137 Primary # Drill Code Primary # AC ault Code 139 Primary # Zone 1 ault Code 140 Primary # Zone 2 ault Code 141 Primary # Zone 3 ault Code 142 Primary # Zone 4 ault Code 143 Primary # Zone 5 ault Code 144 Primary # arth ault Code 145 Primary # Low Battery ault Code 146 Primary # No Battery ault Code 147 Primary # Telco Pri. Line ault Code 148 Primary # Telco Sec. Line ault Code 149 Primary # NAC #1 ault Code 150 Primary # NAC #2 ault Code 151 Primary # Comm Trouble Pri. # Code 152 Primary # Comm Trouble Sec. # Code 153 Primary # Annunciator ault Code 154 Primary # System Off Normal Code 155 Primary # Zone 1 Alarm Restore Code 156 Primary # Zone 2 Alarm Restore Code 157 Primary # Zone 3 Alarm Restore Code 158 Primary # Zone 4 Alarm Restore Code 159 Primary # Zone 5 Alarm Restore Code 160 Primary # Zone 1 Disabled Restore Code 161 Primary # Zone 2 Disabled Restore Code 162 Primary # Zone 3 Disabled Restore Code 163 Primary # Zone 4 Disabled Restore Code 164 Primary # Zone 5 Disabled Restore Code 165 Primary # Drill Restore Code Primary # AC ault Restore Code 167 Primary # Zone 1 ault Restore Code 168 Primary # Zone 2 ault Restore Code 169 Primary # Zone 3 ault Restore Code 170 Primary # Zone 4 ault Restore Code 171 Primary # Zone 5 ault Restore Code 172 Primary # arth ault Restore Code 173 Primary # Low Battery ault Restore Code 174 Primary # No Battery ault Restore Code 175 Primary # Telco Pri. Line ault Restore Code 176 Primary # Telco Sec. Line ault Restore Code 177 Primary # NAC #1 ault Restore Code 178 Primary # NAC #2 ault Restore Code 179 Primary # Comm Trouble Pri. # Restore Code 180 Primary # Comm Trouble Sec. # Restore Code 181 Primary # Annunciator ault Restore Code 182 Primary # System Off Normal Restore Code 183 Primary # System Test Report Primary # System Abnormal Test Report 185 Primary # Request for Up/Download Primary # Successful Upload Primary # Successful Download Primary # ailed Up/Download 7 Table 3-1: vent Codes, Primary Central Station Number 33

34 4+2 Standard and 4+2 xpress ormat If '1, A or C' are entered for address 16, the following data is automatically programmed for the Primary Central Station phone number event codes. nter '00' for the setting to disable the report. Address Description Settings Primary # Zone 1 Alarm Code Primary # Zone 2 Alarm Code Primary # Zone 3 Alarm Code Primary # Zone 4 Alarm Code Primary # Zone 5 Alarm Code Primary # Zone 1 Disable Code Primary # Zone 2 Disable Code Primary # Zone 3 Disable Code Primary # Zone 4 Disable Code Primary # Zone 5 Disable Code Primary # Drill Code Primary # AC ault Code Primary # Zone 1 ault Code Primary # Zone 2 ault Code Primary # Zone 3 ault Code Primary # Zone 4 ault Code Primary # Zone 5 ault Code Primary # arth ault Code Primary # Low Battery ault Code Primary # No Battery ault Code Primary # Telco Pri. Line ault Code A Primary # Telco Sec. Line ault Code B Primary # NAC #1 ault Code C Primary # NAC #2 ault Code C Primary # Comm Trouble Pri. # Code D Primary # Comm Trouble Sec. # Code Primary # Annunciator ault Code C Primary # System Off Normal Code Primary # Zone 1 Alarm Restore Code Primary # Zone 2 Alarm Restore Code Primary # Zone 3 Alarm Restore Code Primary # Zone 4 Alarm Restore Code Primary # Zone 5 Alarm Restore Code Primary # Zone 1 Disable Restore Code Primary # Zone 2 Disable Restore Code Primary # Zone 3 Disable Restore Code Primary # Zone 4 Disable Restore Code Primary # Zone 5 Disable Restore Code Primary # Drill Restore Code Primary # AC ault Restore Code Primary # Zone 1 ault Restore Code Primary # Zone 2 ault Restore Code Primary # Zone 3 ault Restore Code Primary # Zone 4 ault Restore Code Primary # Zone 5 ault Restore Code Primary # arth ault Restore Code Primary # Low Battery ault Restore Code Primary # No Battery ault Restore Code Primary # Telco Pri. Line ault Restore Code A Primary # Telco Sec. Line ault Restore Code B Primary # NAC #1 ault Restore Code C Primary # NAC #2 ault Restore Code C Primary # Comm Trouble Pri. # Restore Code D Primary # Comm Trouble Sec. # Restore Code Primary # Annunciator ault Restore Code C Primary # System Off Normal Restore Code Primary # System Test Report Primary # System Abnormal Test Report Primary # Request for Up/Download Primary # Successful Upload Primary # Successful Download Primary # ailed Up/Download 74 Table 3-2: vent Codes, Primary Central Station Number 34