Small Box for Cable Termination. 3.1 Preparation of box 3.3 Mounting of the box on the wall
|
|
- Stephany McDaniel
- 5 years ago
- Views:
Transcription
1 FIST-SB2-8 I N S T A L L A T I O N I N S T R U C T I O N Small Box for Cable Termination Contents 1 Introduction 1.1 Product description 2 General 2.1 Tools 2.2 Kit contents 3 Installation and pre-assembling of box 3.1 Preparation of box 3.3 Mounting of the box on the wall 4 Cable installation 4.1 Cable preparation- Routing of the cable fibers 4.2 Cable termination 5 Pigtail installation 5.1 Installation pigtails with connectors and installation in the pigtail seal (using connectors) 5.2 Installation pigtails using KTU 5.3 FIST-PTS24 seal in case of 16 pigtails 6 Fiber organization 7 Closing the box 1 Introduction 1.1 Product Description The FIST-SB2-8 is a box for a fiber management system that offers the function of splicing and patching. It provides a mechanical and environmental protection for all the fiber optic components and permits easy access by both the network provider and the customer. The box is applicable indoor and inside street cabinets. The FIST-SB2-8 box is designed to terminate, and patch fibers, it can handle up to 8 connectors. 2 General 2.1 Tools Hammer Screwdriver Marker Fiber guiding pin FACC-tube-cutter-01 to cut loose tubes FACC-TUBE-Stripper-02 to strip loose tubes
2 2.2 Kit contents Depending the network and the construction of the used cables, standard kits or application kits can be ordered, see ordering guide. The standard kit will be: The Cover (including 4 screws) 4 pcs of mounting bolts, plugs and seals for wall mounting. The box base + mounting plate for splicing module (FIST-SOSA2) Pre installed-universal Mounting System profile. - Tray lid and tray wedge - Cable strain relief connector, foam and tie wrap - Patchpannel and cable termination plate - Hinges for cover + instruction - 1 PG 16 pressure gland ø range 6-14 mm The application kits include all the above and the necessary FIST-SOSA2 splicing modules connector adapters and pigtails (pre-installed) splice protectors (SMOUV) or ANT can also be ordered pigtail seals Break out the ports to be used. 3 Installation 3.1 Preparation of box Unlock the screws and remove the cover. Cables can enter the box via bottom (1+2), the right side (3) or the top (4) Install the gland in the selected port and tighten the nut on the inside of the box. 2
3 3.2.2 Feed the cable through the cable port gland. 4 Cable installation 4.1 Cable preparation Prepare the cable, strip and clean the cable over a length of 1800 mm. and cut the strength member at 30 mm length Pull the cable back. the cable jacket should protrude 50 mm into the box. 4.2 Cable termination Mount the strength member connector and tighten the connector with a screwdriver (2). If needed one should release the bolts of the base-plate and lift the base-plate to mount the strength member connector (1) Insert the tie wrap. 3.2 Mounting of the box on the wall 1 30 mm 50 mm Secure the cable with a tie wrap onto the cable attachment plate and fix the strength member Hold the base part onto the wall and use a screwdriver to indicate the position of the 4 holes to be drilled (1). Insert the screws, plugs and tighten. Install the FIST-SOSA. If needed, one can use the 4 knock-out holes to fix the box (2); dimensions at the backside of the box. 3
4 4.2.2 Route the tubes up to the metal tube holder according to the drawings. Mark the loose tubes. Cut and remove the excess of the loose tube and clean the fibers. Fix the loose tube with tie wrap and foam Cable-cable (splice only). Cables can also enter via top or right side Remove the traywedge and lid, route the fibers on the trays. Pull gently on the fibers in the tray and make sure that the fibers are well contained in the wraparound groove plate Store the fibers temporarily on a tray Cable-cable (using connectors). Cables can also enter via top or right side. 4
5 5 Pigtail installation 5.1 Using connectors Insert the pigtails or jumpers in the rubber wrap around seal of the gland Open the gland, remove the rubber wrap around seal, pull the pigtails through the gland, and plug in the connectors (do not forget the nut) Position the rubber pigtail seal in the gland, avoid pigtail crossings in the gland. 5
6 5.2.4 In case of 2 pigtails/ktu;identify 1 of the fibers with a marking pen Guide the prepared pigtails in the KTU.Make sure the Kevlar yarns do not entangle the fibers.keep the Kevlar from each pigtail separated Tighten the gland (see instaled box). 5.2 Installation pigtails using KTU Pull the pigtail through the gland and put a mark at 2 meters of the pigtail end Slide the inner part to the left as much as possible by pulling the jacket and Kevlar at the same time. Cut the excess Kevlar leaving 5-10 mm Remove the jacket beyond the marking point and cut the Kevlar, leaving mm from the edge of the jacket In case of less Kevlar (typically this means pigtail diameter <2,3 mm):wrap the Kevlar to ensure a good strain relief Mount the two pieces as shown. 6
7 5.3 Installation of FIST-PTS 24 seal in case of 16 pigtails Slide the pigtails through the housing and position pigtails into a groove of the seal. Select the groove by turning the ring Mount the KTU in the patch pannel and route the fibers as shown Wrap the seal around the pigtails Mount the foam on the fibers (do not tighten too much) and route the fibers on the trays Slide the seal into the housing by holding the pigtail, and pushing the seal upwards. 7
8 5.3.4 Move the cold seal locking ring onto the housing Fiber routing Fasten the bolt with an Allen key (hand tight, between thumb and forefinger). 8
9 6 Fiber organization on trays after splicing Splice the fibers and take the splice protector and put it centered towards the splice holder Place the fibers back on the tray In case of 4 fibers/tray, one should strip the 900 μ coating away, starting in the groove plates. This is applied when 16 pigtails are spliced. 9
10 7 Closing the box Secure the trays by using the metal tray-wedge When hinges on the cover are applied, follow installation instructions included in the pack Place the cover on the box base and secure the cover with the screws. 10
11 11
12 Tyco Electronics Raychem NV Diestsesteenweg 692 B-3010 Kessel-Lo, Belgium Tel.: Fax: Tyco Electronics, TE logo and FIST are trademarks. Kevlar is a trademark of E.I. du Pont de Nemours. The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, Tyco Electronics makes no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. Tyco Electronics obligations shall only be as set forth in Tyco Electronics Standard Terms and Conditions of Sale for this product and in no case will Tyco Electronics be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of Tyco Electronics products should make their own evaluation to determine the suitability of each such product for the specific application. TC 626/IP/3 05/03
FIST-EDSA-D4. 3 Feeder cable/ducts (max 16 mm) 4 Drop cable (DB cable or guiding tubes 5-8 mm) 5 Adding drop cable. 6 Gel part replacement
FIST-EDSA I N S T A L L A T I O N I N S T R U C T I O N FIST-EDSA-D4 Content 1 Introduction 2 Kit content 3 Feeder cable/ducts (max 16 mm) 4 Drop cable (DB cable or guiding tubes 5-8 mm) 5 Adding drop
More informationSeal Kits for BUDI Enclosures
Description BUDI is a product range of compact, wall mountable fiber enclosures for indoor and outdoor use. They are specifically designed for fast deployment and easy customer connection. The FIST management
More informationSpecification Control Drawing for the FIST MK2 Organizer Components
Page 1 of 15 Prepared by: art Herremans Approved by: Jan Vandenbroeck Product Manager Specification Control Drawing for the FIST MK2 Organizer Components Splicing only sub-assembly 2 Single circuit tray
More informationBUDI-M-SP. Building distributor. Introduction. Seals. Kit content. Accessories. Wrap around cable seals
BUDI-M-SP I N S T A L L A T I O N I N S T R U C T I O N Building distributor Introduction Suitable for FTTH applications where easily pre-connectorized splittersmodules can be build in. The box is designed
More informationA world of fiber Product overview
A world of fiber Product overview Solutions for fiber optic networks Solutions for fiber optic networks Drawing on years of experience and expertise in materials science technology, optics, product design
More informationFOSC. Fiber Optic System Technology. Fiber Optic Splice Closures (FOSC-400)
FOSC Ordering Guide FOSC Fiber Optic System Technology Fiber Optic Splice Closures (FOSC-400) This document provides assistance with the selection of FOSC-400 closures. It includes the following sections:
More informationRayClic Connection System
RayClic Connection System RayClic-S Splice Kit RayClic-T Tee and End Seal Kit RayClic-X Cross and End Seal Kit Installation Instructions Description These kits are for use with Raychem IceStop, XL-Trace
More informationTE Connectivity's AMP NETCONNECT Cable Management
One of the major challenges facing cabling mounting holes installers and maintenance personnel is organizing distribution cables and patch cords in the telecommunications room. TE Connectivity's AMP NETCONNECT
More informationJBM-100-LBTV2 Power Connection, Powered Splice, Dual Power Connection, or Splice with Junction Box
JBM-100-LBTV2 Power Connection, Powered Splice, Dual Power Connection, or Splice with Junction Box Installation Instructions Description The JBM-100-LBTV2 is a Type 4X-rated connection kit. It is designed
More informationC A Heating Cable Gland Kit
C75-100-A Heating Cable Gland Kit Installation Instructions Description The C75-100-A is a NEMA 4X rated gland kit used to transition heating cables into a junction box when making connections off of a
More informationPT9150 (Extended Range)
(Extended Range) Cable Actuated Sensor Extended Ranges Incremental Encoder Linear Position to 1700 inches (4300 cm) Stroke Range Options: 0-600 to 0-1700 inches VLS Option to Prevent Free-Release Damage
More informationFiber Optic Products Catalog
Fiber Optic Products Catalog No epoxy, no polish, no crimp Two fibers in one ferrule MT-RJ Patch Panel Jack packages include: 6 MT-RJ Jacks 2 Actuator Tools 1 Fiber Guide 1 Icon Wheel Bend Limiting Boots
More informationC Electrical Connection Kit
1548-4010C Electrical Connection Kit For Use With Dekoron 2700 and 2300 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4010C electrical connection and end seal kit
More informationP125 High Pressure Sensor
High Pressure Sensor SPECIFICATIONS Ranges from 2000 to 7000 bar (30k to 100k psi) Stainless steel pressure port Robust for Fatigue testing For static and dynamic applications Linearity up to ±0.3% F.S.
More informationPT9600. Cable Actuated Encoder Reel. General. Environmental
Cable Actuated Encoder Reel Converts ANY Rotary Encoder to a Linear Position Sensor Linear Stroke Range up to 550 inches (14 m) Mates Virtually ANY Customer Supplied Encoder Factory Supplied Encoder Available
More informationSide Entry Bushing (SEB) High Temperature Cable Clamp Bushing Installation Instructions
Page: 1 of 6 High Temperature Cable Clamp Bushing is a strain relief, and stress protection product that can be placed around a wire bundle and under a saddle clamp backshell adapter after the contacts
More informationENERGY /// RAYCHEM CABLE CLAMPS RAYCHEM CABLE CLAMPS. Quick Reference Guide
ENERGY /// RAYCHEM CABLE CLAMPS RAYCHEM CABLE CLAMPS WHAT MAKES RAYCHEM CABLE CLAMPS THE INDUSTRY LEADER? Integral stainless steel clamping plates to ensure consistent clamping pressure on both sides.
More informationCable Actuated Sensor Industrial Incremental Encoder Output
Cable Actuated Sensor Output Linear Position up to 175 inches (3 meters) 0-125, 0-175 inch Full Stroke Range Options Designed for Outdoor & IP67 environments In Stock for Quick Delivery! 175-inch model
More informationXAGA 550/550-L. Aerial Splice Closure. 1. General Description. 2. Warnings. 3. Cautions
XAGA 550/550-L Aerial Splice Closure I N S T A L L A T I O N I N S T R U C T I O N S 1. General Description 1. This practice provides information regarding the description and use of the XAGA 550/550-L
More informationPT9101. General. Potentiometer Cycle Life 250,000 Maximum Retraction. Weight, Aluminum (Stainless 8 lbs. (16 lbs.) max. Electrical
Cable Actuated Sensor Absolute Linear Position to 550 inches (1400 cm) Aluminum or Stainless Steel Enclosure Options VLS Option to Prevent Free-Release Damage IP68 NEMA 6 Protection General Full Stroke
More informationSGJ. 80, 120-inch Stroke Range Options. Polycarbonate Enclosure IP67. In Stock for Quick Delivery. General. CANbus Specifications
Cable Actuated Sensor Compact Mid-Range String Pot Absolute Position 80, 120-inch Stroke Range Options Polycarbonate Enclosure IP67 In Stock for Quick Delivery General Stroke Range Options Accuracy Repeatability
More information86 Compensated SPECIFICATIONS. 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage Temperature Compensated
SPECIFICATIONS 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage Temperature The 86 compensated is a small profile, media compatible, piezoresistive silicon pressure sensor packaged
More information82 Constant Voltage SPECIFICATIONS. 316L SS Pressure Sensor 19mm Diameter Package 0-100mV Output Absolute and Gage Temperature Compensated
SPECIFICATIONS 316L SS Pressure Sensor 19mm Diameter Package 0-100mV Output Absolute and Gage Temperature Compensated The 82 constant voltage is a 19 mm small profile, media compatible, piezoresistive
More informationED-18 Analog Output Series Magnetic Encoder SPECIFICATIONS
ED-18 Analog Output Series Magnetic Encoder SPECIFICATIONS Analog voltage or current output Low profile IP52 sealing Sleeve or ball bearing Excellent stability no optic degradation The ED-18 Series Magnetic
More informationSKJ. Specifications. Stroke Range Options 250 inches (6.4 m), 400 inches (10.2 m)
Cable Actuated Sensor Linear Position to 400 inches (10 m) Compact Design Simple To Install User Adjustable Measuring Cable Orientation IN STOCK for Quick Delivery! Specifications Stroke Range Options
More informationPT9420 (Extended Range)
(Extended Range) Cable Actuated Sensor Absolute Linear Position to 1700 inches (4300 cm) Stroke Range Options: 0-600 to 0-1700 inches VLS Option to Prevent Free-Release Damage IP68 NEMA 6 Protection Hazardous
More information154BC SPECIFICATIONS FEATURES APPLICATIONS STANDARD RANGES
SPECIFICATIONS Low Cost 316L Stainless Steel or Titanium 19mm Diameter Package 0-100mV Output Gage and Absolute Wide Compensated Temperature Range FEATURES O-Ring Mount -20ºC to +85ºC Compensated Temperature
More informationAMP SUPERSEAL 1.5 SERIES Connectors
Introduction Tyco Electronics has developed the MP SUPERSEL 1.5 SERIES Connector family to meet the increasing requirements for reliability and water proofness. MP SUPERSEL 1.5 SERIES Connector exceed
More information154BC SPECIFICATIONS. Please refer to the 154N uncompensated and constant voltage datasheets for more information on different features of the 154.
SPECIFICATIONS Low Cost 316L Stainless Steel or Titanium 19mm Diameter Package 0-100mV Output Gage and Absolute Wide Compensated Temperature Range The 154BC is a 19mm small profile, media compatible, piezoresistive
More informationRibbon Breakout Kit Installation Instructions
Ribbon Breakout Kit Installation Instructions LOOSE BUFFER TUBE RIBBON KIT BLK-RLBT- (SEE PAGE 3) CENTRAL OVAL TUBE RIBBON KIT BLK-RCT- (SEE PAGE 12) RIBBON CENTRAL TUBE KIT BLK-RCT- (SEE PAGE 20) 19645-A
More information316L SS Pressure Sensor High Pressure 0-100mV Output Absolute
SPECIFICATIONS 316L SS Pressure Sensor High Pressure 0-100mV Output Absolute The 89 uncompensated is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless
More informationCable Actuated Sensor Industrial User Scalable 4 20mA
Cable Actuated Sensor User Adjustable Stroke Range to 175 inches (3 meters) Easy Push-Button Zero and Span Adjust Designed for Outdoor & IP67 environments In Stock for Quick Delivery! 175-inch model shown
More informationPT101. General. Full Stroke Range Options. Potentiometer Cycle Life Maximum Retraction Acceleration. Electrical
Cable Actuated Sensor Absolute Linear Position Classic Stringpot Design Stroke Range Options: 0 2 to 0 100 inches Powder Painted & Anodized Aluminum Enclosure Industrial Automation & Testing Applications
More informationTTSIM-1A. TraceTek Sensor Interface Module with Relay. Installation/Operation Instructions. Installation Items (not supplied) Tools Required.
TTSIM-1A TraceTek Sensor Interface Module with Relay Installation Items (not supplied) General Information Installation/Operation Instructions Please read these instructions and keep them in a safe place.
More information85 Compensated SPECIFICATIONS. 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage Temperature Compensated
SPECIFICATIONS 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage Temperature The 85 compensated is a small profile, media compatible, piezoresistive silicon pressure sensor packaged
More information86A SPECIFICATIONS. 316L SS Pressure Sensor Small Profile V High Level Output Gage, Absolute ASIC Calibrated
(Image displays Absolute type) 86A SPECIFICATIONS 316L SS Pressure Sensor Small Profile 0.5-4.5V High Level Output Gage, Absolute ASIC Calibrated The 86A is a small profile, media compatible, piezoresistive
More informationMSP100 Pressure Transducer
SPECIFICATIONS Analog and 14-Bit Digital Output Small Size Low Cost 316L Stainless Steel or 17-4PH FEATURES Single Piece Construction; No Welds, No Oil 100% Stainless Steel Isolation for Harsh Chemical
More informationDP86 Constant Voltage with Fitting
SPECIFICATIONS 316L SS Wet/Wet Differential Low Pressure 0 100mV Output The DP86 constant voltage with fitting differential pressure sensor is a double-sided, media compatible, piezoresistive silicon pressure
More informationMS1471 SPECIFICATIONS. PC Board Mountable Pressure Sensor 0-60 mv Output Gage and Absolute Low Cost
SPECIFICATIONS PC Board Mountable Pressure Sensor 0-60 mv Output Gage and Absolute Low Cost The MS1471 is a piezoresistive silicon pressure sensor packaged in a surface mount configuration. It is intended
More informationCable Actuated Sensor Industrial User Scalable VDC Output
Cable Actuated Sensor Industrial User Scalable VDC Output User Signal Adjustable Stroke Range to 175 inches (3 meters) User Selectable 0 5, 0 10, 5 +5, 10 +10 VDC Output Designed for Outdoor & IP67 environments
More information85 Uncompensated SPECIFICATIONS FEATURES APPLICATIONS STANDARD RANGES. 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage
FEATURES Weldable and Threaded Process Fittings -40ºC to +125ºC Operating Temperature ±0.1% Pressure Non Linearity Solid State Reliability APPLICATIONS Medical Instruments Process Control Fresh & Waste
More information86 Compensated SPECIFICATIONS. 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage Temperature Compensated
Compensated SPECIFICATIONS 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage Temperature Compensated The 86 compensated is a small profile, media compatible, piezoresistive silicon
More informationMEAS SENSOR TAG APP INSTALLATION GUIDE FOR IOS
INSTALLATION GUIDE FOR IOS This document describes the installation of the Measurement Specialties sensor tag application for ios. Contents 1 Installation... 2 1.1 Prerequisite... 2 1.2 Download Application...
More informationSPECIFICATIONS. SENSOR SOLUTIONS ///LM Page 1 09/2015
SPECIFICATIONS 316L SS Pressure Sensor with PVC Threads Small Profile 4.5V (typ) High Level Output Gage, Absolute, Sealed Gage ASIC Calibrated Variety of Cable Lengths The LM incorporates stainless steel
More informationStandard SPECIFICATIONS FEATURES APPLICATIONS
SPECIFICATIONS PC Board Mountable Pressure Sensor 0-50 mv Output Voltage Excitation Gage, Absolute, and Differential Temperature Compensated FEATURES Dual-in-Line Package 0ºC to 50ºC Compensated Temperature
More informationMEAS SENSOR TAG APP INSTALLATION GUIDE FOR ANDROID
INSTALLATION GUIDE FOR ANDROID This document describes the installation of the Measurement Specialties sensor tag application for Android devices. Contents 1 Installation... 2 1.1 Prerequisite... 22 1.2
More informationMSP100 Pressure Transducer
SPECIFICATIONS Analog and 14-Bit Digital Output Available Small Size Low Cost 316L Stainless Steel or 17-4PH FEATURES Single Piece Construction; No Welds, No Oil 100% Stainless Steel Isolation for Harsh
More informationGardian W51. Approvals
Gardian W51 120 V pre-assembled electric heating cables for pipe freeze protection and roof & gutter de-icing Installation Instructions Description Gardian W51 120 V pre-assembled self-regulating heating
More information89BSD Digital Output
SPECIFICATIONS Stainless Steel with O-Ring Seal Pressure/Temperature Read-Out (24-bit DS ADC) ASIC Calibrated Absolute, Sealed Gage 9mm Diameter The 89BSD is a 9mm diameter small profile, media compatible,
More informationLOW PRESSURE Intrinsically Safe Transducer AST44LP
Intrinsically Safe Transducer AST44LP Overview The AST44LP is a stainless steel pressure transducer with a wide variety of options. With its rugged construction and the best price-toperformance ratio in
More informationSub psi SPECIFICATIONS
SPECIFICATIONS PC Board Mountable Pressure Sensor 40 mv Output Typical Differential Pressures Metal Tube and Ceramic Barbed Ports Temperature Compensated The 1210 sub PSI is a temperature compensated,
More informationRaychem Heating System
Raychem Heating System Tank Heater (H55207) Approvals F M APPROVED Ordinary and Hazardous Locations lass I, Div. 2, Groups B,, D lass II, Div. 1 & 2, Groups E, F, G lass III All hazardous location applications
More information86BSD Digital Output
SPECIFICATIONS Stainless steel with O-ring seal Pressure/temperature read-out Digital output ASIC calibrated Absolute, gage Cable/connector option Low power option 16mm diaphragm diameter The 86BSD is
More information86 Compensated SPECIFICATIONS. 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage Temperature Compensated
Compensated SPECIFICATIONS 316L SS Pressure Sensor Small Profile 0-100mV Output Absolute and Gage Temperature Compensated The 86 compensated is a small profile, media compatible, piezoresistive silicon
More informationThis document provides assistance with the selection of elements of the C5C copper pairs connection system. It includes the following sections:
ORDERING GUIDE FOR THE TYCO-C5C COMPACT CAT 5 COMPATIBLE COPPER PAIRS CONNECTION SYSTEM This document provides assistance with the selection of elements of the C5C copper pairs connection system. It includes
More informationCABLES AND ACCESSORIES FOR TRUBLUE DATA LOGGERS
CABLES AND ACCESSORIES FOR TRUBLUE DATA LOGGERS CONTENTS TruBlue Cable Attachment System 2 Field Cables for Vented Gage Water Level Data Loggers 853-XXXXX, Interface Cable Assembly 3 Field Cables for Absolute
More informationINTRINSICALLY SAFE Pressure Transducer / Transmitter AST4400
Pressure Transducer / Transmitter AST4400 Overview The AST4400 is a stainless steel pressure transducer with a wide variety of options. With its rugged construction and best price-toperformance ratio in
More informationJB-RTD-STAND RTD PIPE STAND FOR COMBINATION POWER CONNECTION BOX AND ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS
JB-RTD-STAND RTD PIPE STAND FOR COMBINATION POWER CONNECTION BOX AND ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS JB-RTD-STAND with Raychem heating cable DESCRIPTION The Raychem JB-RTD-STAND is a combination
More informationAquiTron. AT-LDM Liquid Detection Module INSTALLATION INSTRUCTIONS
AquiTron Liquid Detection Module INSTALLATION INSTRUCTIONS Please read these instructions carefully and keep them in a safe place (preferably close to the module) for future reference. These instructions
More information316L SS Pressure Sensor High Pressure 0-100mV Output Absolute
SPECIFICATIONS 316L SS Pressure Sensor High Pressure 0-100mV Output Absolute The 89 uncompensated is a small profile, media compatible, piezoresistive silicon pressure sensor packaged in a 316L stainless
More information86BSD Digital Output
SPECIFICATIONS Stainless steel with O-ring seal Pressure/temperature read-out Digital output ASIC calibrated Absolute, gage Cable/connector option Low power option 16mm diaphragm diameter The 86BSD is
More informationQuickStat-TC Installation & Operation Manual
QuickStat-TC Installation & Operation Manual General Information A F Use of this Manual This manual covers the installation and operation of the Raychem QuickStat-TC thermostat and must be used with the
More informationTS105-10L5.5MM Thermopile Sensor
SPECIFICATIONS Thermopile IR-Sensor For Contactless Temperature Measurement Single Element For Industrial Pyrometers Silicon Lens Accurate Reference Sensor Thermopiles are mainly used for contactless temperature
More informationUV-SCE. Ultra-Violet light, Resistant TECHNICAL DATASHEET. Heat Shrink Identification Marker Sleeves
UV-SCE Ultra-Violet light, Resistant Heat Shrink Identification Marker Sleeves TECHNICAL DATASHEET Revision 4, March 2015 UV-SCE Ultra-Violet Light Resistant, Heat Shrink Identification Marker Sleeves
More informationMEAS EMITTER ASSEMBLY ELM-4000 SERIES
MEAS EMITTER ASSEMBLY ELM-4000 SERIES SpO2 optical sensor component Dual Drive Lead Frame Construction Pulse Oximetry Component Clear Epoxy Low oxygen level can put a strain on cell functioning including
More informationHVS S Splice Series
HVS-3-2520S Splice Series 25kV lass Splice for 3 Extruded Dielectric (Poly/EPR) Power ables: Metallic Tape, Wire Shield, UniShield, or Lead Sheath ables Suggested Installation Equipment (not supplied with
More informationELAF LOAD CELL SPECIFICATIONS FEATURES
FEATURES Low Cost Optional High Level Output Small, Low Profile Design Low Noise Robust: High Over Range High Reliability Low Deflection Low Off-Axis Response APPLICATIONS Theatrical Rigging Loads Assembly
More informationMODEL 4000A & 4001A ACCELEROMETER
MODEL 4000A & 4001A ACCELEROMETER dimensions 4001A Connector Attachment SPECIFICATIONS Silicone MEMS Accelerometer Signal Conditioned Output Temperature Calibrated Low Cost, Lightweight The Model 4000A
More informationDOG2 MEMS SERIES USB INCLINOMETER
1 DOG2-USB_1630-21559-0018-E-0118 DOG2 MEMS SERIES USB INCLINOMETER SPECIFICATIONS Dual axis inclinometer Measurement range ±90 High resolution Good accuracy Fast response time Easy to use software FEATURES
More informationDTS SERIES CONNECTORS
DEUTSCH DTS SERIES CONNECTORS FOR MIL-DTL-38999 SERIES III RUGGED, HARSH ENVIRONMENT SUBMINIATURE CONNECTORS TE DEUTSCH MIL-DTL-38999 SERIES III CONNECTORS QUICK REFERENCE GUIDE Wide Range Mil spec, commercial,
More informationGas Discharge Tubes GTCX25-XXXM-R02 Series
Raychem Circuit Protection 5mm 2Pole GDTs (ceramic gas discharge tubes), are commonly used to help protect sensitive telecom equipment such as communication lines, signal lines and data transmission lines
More informationTraceTek TT1000 Modular Sensing Cable
LEAK DETECTION powered by Installation Instructions TraceTek TT1000 TraceTek TT1000 Modular Sensing Cable Modular Sensing Cable General Information These instructions explain the proper procedures for
More informationINTRINSICALLY SAFE Pressure Transducer / Transmitter AST4401
Pressure Transducer / Transmitter AST4401 Overview The AST4401 is a stainless steel pressure transducer with a wide variety of options. With its rugged construction and best price-toperformance ratio in
More informationMSP340 Pressure Transducer
Shown with Packard Connector Shown with Packard Connector MSP40 SPECIFICATIONS Low Cost OEM 100% Leak Proof No O-Rings No Silicon Oil No Welds FEATURES One-Piece Stainless Steel Construction Ranges up
More informationMEAS Subermsible Liquid Level Pressure Transducer SPECIFICATIONS. Features. Applications
MEAS 5700 Subermsible Liquid Level Pressure Transducer Features Heavy Industrial CE Approval 10 V/m EMI Protection Reverse Polarity Protection on Input Short Circuit Protection on Output ±0.25% Accuracy
More informationGelCap SL. GelCap SL splice cover kits quickly and con-veniently insulate, seal, and protect stub splice connections up to 1000 volts.
Cold-Applied Splices GelCap SL Stub splice cover kit with connector for use with street lighting (1000 V) 34 Tyco Electronics GelCap SL splice cover kits provide quick installation, dependable performance,
More informationGas Discharge Tubes GTCX28-XXXM-R05 Series
GTCX28-XXXM-R05 Series Raychem Circuit Protection Products 8mm 2Pole GDTs (ceramic gas discharge tubes), are commonly used to help protect sensitive telecom equipment such as communication lines, signal
More informationIndustrial Strength Leak Detection
Industrial Strength Leak Detection Don t let an undetected leak or spill ruin the environment or your reputation... TraceTek Technology: Find leaks before major damage is done... TraceTek Technology: Sensor
More informationGas Discharge Tubes. Features: Benefits: Applications:
TE Circuit Protection 5mm 3Pole GDTs (ceramic gas discharge tubes), are commonly used to help protect sensitive telecom equipment such as communication lines, signal lines and data transmission lines from
More informationM7100 Pressure Transducer
SPECIFICATIONS Performance standard on and off highway engine and vehicle OEMs Rugged for heavy equipment and outdoor use Designed specifically for high volume applications Stainless steel wetted surfaces
More informationU86B. Urea Dosing SPECIFICATIONS FEATURES APPLICATIONS
SPECIFICATIONS Mountable with O-ring seal Stainless Steel wetted surfaces Amplified ASIC calibrated Absolute, sealed gage Cable option Analog output SENT Output Optional (contact factory for details) FEATURES
More informationFC22 Compression Load Cell
SPECIFICATIONS 10 100 lbf Ranges High Level or mv Outputs Interchangeable Compact Easy to Fixture Design CE Compliance FEATURES Small Size Low Noise Robust: High Over-Range Capability High Reliability
More informationBridge to Splice Presser 710-BSP
Bridge to Splice Presser 710-BSP Instructions November 2004 78-8135-2810-2-B 1.0 General 1.1 The 3M Bridge to Splice Presser 710-BSP is a hand tool used to press 3M Bridge Modules 710 and 3M Splice or
More informationDOG2 MEMS SERIES CAN J1939 INCLINOMETER
DOG2 MEMS SERIES CAN J1939 INCLINOMETER SPECIFICATIONS Dual axis inclinometer Measurement ranges ±90 CAN J1939 interface FEATURES 8 30 VDC supply voltage Digital signal processing includes o filter (e.g.
More informationTESS WIRELESS SENSOR TAG DEMO V1.1
TESS WIRELESS SENSOR TAG DEMO V1.1 Standard 2.4GHz Wireless Communication Tag Humidity: 0-100% RH Temperature: -20 C to +85 C Pressure: 300 to 1,200mBar Applications Smart building Smart home HVAC controller
More information86BSD Digital Output
SPECIFICATIONS Stainless steel with O-ring seal Pressure/temperature read-out Digital output ASIC calibrated Absolute, gage Cable/connector option Low power option 16mm diaphragm diameter The 86BSD is
More informationNG4access ODF Platform Standard Chassis Installation Manual
NG4access ODF Platform Standard Chassis Installation Manual TECP-90-703 Issue 1 8/2012 24939-A Content Page INTRODUCTION...1 1 PRODUCT DESCRIPTION...2 2 MAIN COMPONENTS...3 3 GROUNDING AND BONDING THE
More informationHVS S 15kV Class
Product Installation Instructions HVS-3-1520S 15kV lass Splice for 3/ Extruded Dielectric (Poly/EPR) Power able: Metallic Tape, WireShield, or UniShield able * UniShield is a registered trademark of I
More informationINSTALLATION INSTRUCTIONS TOOLS YOU WILL NEED GETTING STARTED
INSTALLATION INSTRUCTIONS HONEYCOMB SHADES STANDARD RECTANGULAR Thank you for your purchase. This shade has been custom built for you from the highest quality materials. To avoid errors and save valuable
More informationOPERATION MANUAL Model 8011 & mA
OPERATION MANUAL Model 8011 & 8021 4-20mA TE CONNECTIVITY SENSORS/// MODEL 8011 & 8021 4-20MA 05/2016 Page 1 WARRANTY Measurement Specialties, Inc. accelerometers are warranted during a period of one year
More informationDESTU. Direct Entry Sealed Termination Unit. Installation Instructions. Suitable for use in either safe or hazardous areas.
DESTU Direct Entry Sealed Termination Unit Installation Instructions Suitable for use in either safe or hazardous areas R II 2 G EEx e II Heat Trace Limited, Mere s Edge, Chester Road, Helsby, Frodsham,
More informationDSS SERIES. Single Channel Hall Effect Speed Sensor. Product ID
Product ID Type # Product # Drawing # 378Z-05380 DSS 1210.00 STV (5m) 113807 374Z-04996 DSS 1210.02 PHV 112705 374Z-05052 DSS 1210.02 SHV (2m) 112865 378Z-05864 DSS 1210.12 AHV 115675 378Z-05910 DSS 1210.13
More informationSUBMERSIBLE Flush Diaphragm Liquid Level Sensor AST4520
Flush Diaphragm Liquid Level Sensor AST4520 Overview The AST4520 Flush Submersible liquid level sensor is the cost effective solution for level monitoring of turbulent tanks with viscous media. Approved
More informationINSTALLATION INSTRUCTIONS. WOOD BLINDS 1-3/8, 2 and 2-3/8 SLAT SIZES. FAUX WOOD BLINDS 2 and 2-1/2 SLAT SIZES
INSTALLATION INSTRUCTIONS WOOD BLINDS 1-3/8, 2 and 2-3/8 SLAT SIZES FAUX WOOD BLINDS 2 and 2-1/2 SLAT SIZES STANDARD CORDLESS LIFT Thank you for your purchase. This blind has been custom built for you
More informationRF one-step BNC/TNC connectors for coaxial cable termination
Easy, quick installation Outstanding cable-retention force Solder-solder connection type (center conductor and braid) RF one-step BNC/TNC connectors for coaxial cable termination Applications RF one-step
More informationAir Conditioner. user installation & manual manual. imagine the possibilities
ARFSSSBWK Series ARFSSSCUR AJ JNADCH Series Air Conditioner user installation & manual manual This manual is made with 100% recycled paper. imagine the possibilities Thank you for purchasing this Samsung
More informationEldex Column Heater. Operator s Manual
Eldex Eldex Column Heater Operator s Manual Eldex Laboratories, Inc. 30 Executive Court Napa, CA 94558 Tel: (707) 224-8800 Fax: (707) 224-0688 www.eldex.com Rev. B: 081700 2000Eldex Laboratories, Inc.
More informationHWT-P HWAT POWER CONNECTION KIT WITH END SEAL INSTALLATION INSTRUCTIONS
HWT-P HWAT POWER CONNECTION KIT WITH END SEAL INSTALLATION INSTRUCTIONS DESCRIPTION The Raychem HWT-P Power Connection and End Seal Kit is for use with HWAT heating cables. Materials for one power connection
More informationINSTALLATION INSTRUCTIONS. Aluminum Blinds - Standard - - Lift & Lock -
1 INSTALLATION INSTRUCTIONS Aluminum Blinds - Standard - - Lift & Lock - 1 Deluxe 1 Traditional 1 Value & 1 Basic 2 Macro Thank you for your purchase. This blind has been custom built for you from the
More information