HEXA PROGRAMMING: STREAMLINED SECTION PROGRAMMING

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "HEXA PROGRAMMING: STREAMLINED SECTION PROGRAMMING"

Transcription

1 SOFTWARE VERSI 3.10 CTROL PANEL RESET: Installer lock must be unlocked. (Address 058: enter any value other than 147) Power down reset (1) Remove battery and AC to power down the unit. (2) Connect a jumper between "reset jumper" pins. (3) Connect AC then the battery. (4) Wait 10 seconds. (5) Remove jumper. Factory default installer and master codes will be reinstated. Values entered at addresses , and as well as all user codes, will be erased ([2ND] [2ND]). Programmed values of all other addresses do not change. HEXA PROGRAMMING: All digits from 0 to F are valid. Values are programmed into memory locations from address 000 to 043 and from address 300 to ) Press [ENTER] + installer code. 2) [ENTER] will flash (programming mode). 3) Enter 3 digit memory address. 4) Current value will be displayed on keypad. 5) Enter 2 digit data. 6) Go to step 3 for next address. To exit programming mode, press [CLEAR]. HEXA DISPLAY If key is lit = 8 = 4 = 2 = 1 If key is lit = 8 = 4 = 2 = 1 Value of 2 ND digit = 10 ( = 10) Value of 1 ST digit = 3 ( = 3) VALUE = "3A" No display = SKIP (empty) No light = 0 10 = [0] = [A] STREAMLINED SECTI PROGRAMMING Can be used to program s 00 to 67. (addresses 000 to 043 and 300 to 527) Press [ENTER], installer code, and [7]. ([2ND] and [ENTER] keys alternately flash.) Enter a 2-digit number, followed by 8 digits to program that (confirmation beep). Data will be saved automatically and the software advances to the next programming. To exit programming mode press [CLEAR]. INSTALLER CODE: (reset code ) (addresses 000, 001, 002) SECTI 00 Full access to programming, except access codes. (addresses ) No access to arming/disarming. Can be used to modify installer code. Use only numeric keys from [1] to [10]. (key [10] = 0) PANEL ANSWER OPTIS: (address 003) SECTI 00 First digit disables Answering Machine Override (key [2ND] or key [1]), or determines period of time between first and second call (see table below). Second digit determines number of rings required before panel will answer. If [2ND][2ND] is entered, panel will not answer. (Default value is [2ND] [8].) - 1 -

2 TELEPHE AND ACCOUNT NUMBERS: (reset empty) If only one central station phone number is used, program the same number for telephone number 1 and 2. [10] = the number "0" [BYP] = switch from pulse to tone while dialing [11] = * [MEM] = pause 4 seconds [12] = # [TRBL] = end of number COMPUTER TELEPHE NUMBER: (View at addresses 008 to 015.) 02 / / / / / / / 03 / / / / / / / Press [TRBL] to end phone number if less than 16 digits are programmed. CENTRAL STATI TELEPHE NUMBER 1: (View at addresses 016 to 023.) 04 / / / / / / / 05 / / / / / / / Press [TRBL] to end phone number if less than 16 digits are programmed. CENTRAL STATI TELEPHE NUMBER 2: (View at addresses 024 to 031.) 06 / / / / / / / 07 / / / / / / / Press [TRBL] to end phone number if less than 16 digits are programmed. ACCOUNT "A" AND "B": (View at addresses 032 to 035.) 08 / / / / / / A B For 3 digit account numbers, enter "skip" ([2ND]) as first digit. If only one account number is required, the same number must be entered for both account "A" and "B"

3 Data Description Address 09 [2 ND ] ND] [2 ND] Future use 1st digit: value must be entered i.e. 2nd digit: time correction (See table) 1st digit: telephone 1 format 2nd digit: telephone 2 format 1st digit: PGM 1 type 2nd digit: PGM 2 type [2 ND] TIME CORRECTI: (address [2 ND] [1] [2] [3] [4] [5] [6] [7] 037 second digit) - No adjustment - Plus 4 sec. - Plus 8 sec. - Plus 12 sec. - Plus 16 sec. - Plus 20 sec. - Plus 24 sec. - Plus 28 sec. [8] [9] [10] [11] [12] [ BYP] [ MEM] [ TRBL] - Minus 4 sec. - Minus 8 sec. - Minus 12 sec. - Minus 16 sec. - Minus 20 sec. - Minus 24 sec. - Minus 28 sec. - Minus 32 sec. 10 PGM 1 PGM 2 PGM mask 1 PGM mask COMMUNICATOR FORMATS Key [2 ND ] = ADEMCO slow (1400Hz, 1900Hz, 10bps) [6] [1] [2] [3] [4] [5] = (1400Hz, 1800Hz, 10bps) = SILENT KNIGHT fast (1400Hz, 1900Hz, 20bps) = SESCOA (2300Hz, 1800Hz, 20bps) = RADIICS (40bps with 1400Hz handshake) = RADIICS (40bps with 2300Hz handshake) [7] [8] [9] [10] [ TRBL] = RADIICS with PARITY (1400Hz, 40bps) = RADIICS with PARITY (2300Hz, 40bps) = ADEMCO express = ADEMCO contact ID (programmable codes) = ADEMCO contact ID (all codes) = DTMF - no handshake (personal dialing) PROGRAMMABLE CTACT ID EVENT CODES All addresses from 300 to 527 (s 11 to 67 ) programmed with values other than [2 ND] [2 ND] will report the contact ID codes corresponding to the values programmed. Values to be programmed should be selected from this table. CID 100: 110: 111: 112: : 115: 116: 117: 118: 120: 121: 122: 123: 130: 131: 132: 133: 136: 137: 138: 140: 150: 151: 152: 153: 154: 155: 156: 157: 158: 159: 161: REPORTING CODE AUXILIARY ALARM FIRE ALARM FIRE SMOKE COMBUSTI WATER FLOW HEAT PULLSTATI DUCT FLAME NEAR ALARM PANIC ALARM DURESS SILENT PANIC AUDIBLE PANIC BURGLARY PERIMETER BURG. INTERIOR BURG. 24HR BURGLARY BURGLARY OUTDOOR BURGLARY TAMPER BURGLARY NEAR ALARM GENERAL ALARM 24 HOUR AUX GAS DETECTED REFRIGERATI LOSS OF HEAT WATER LEAKAGE FOIL BREAK ALARM DAY TROUBLE ALARM LOW GAS LEVEL HIGH TEMPERATURE LOW TEMPERATURE LOSS AIR FLOW PROG. VALUE [2 ND] / [1] [2 ND] / [2] [2 ND] / [3] [2 ND] / [4] [2 ND] / [5] [2 ND] / [6] [2 ND] / [7] [2 ND] / [8] [2 ND] / [9] [2 ND] / [10] [2 ND]/[11] [2 ND] / [12] [2 ND]/[ BYP] [2 ND]/[ MEM] [2 ND]/[ TRBL] [1]/[2 ND] [1] / [1] [1] / [2] [1] / [3] [1] / [4] [1] / [5] [1] / [6] [1] / [7] [1] / [8] [1] / [9] [1] / [10] [1]/[11] [1] / [12] [1]/[ BYP] [1]/[ MEM] [1]/[ TRBL] [2]/[2 ND] [2] / [1] CID 300: 301: : 306: 309: 320: 321: 323: 350: 351: 354: 370: 371: 372: 373: 382: 383: 400: 401: 402: 403: 404: 407: 410: 441: 570: 572: 573: 574: 601: 602: 625: REPORTING CODE SYSTEM TROUBLE AC LOSS LOW SYSTEM BATTERY SYSTEM RESET PROGRAM CHANGED BATTERY TEST FAIL SOUNDER/RELAY TROUBLE BELL 1 TROUBLE ALARM RELAY TROUBLE COMMUNICATI TROUBLE TELCO 1 FAULT FAIL TO COMMUNICATE PROTECTI LOOP TROUBLE PROTECTI LOOP OPEN PROTECTI LOOP SHORT FIRE LOOP TROUBLE SENSOR TROUBLE SENSOR TAMPER OPEN/CLOSE OPEN/CLOSE BY USER # GROUP OPEN/CLOSE AUTOMATIC OPENING/CLOSING LATE TO OPEN/CLOSE REMOTE ARM DOWNLOAD REMOTE ACCESS OPEN/CLOSE - STAY MODE BYPASS 24 HOUR ZE BYPASS BURGLARY BYPASS # GROUP BYPASS MANUAL TEST PERIODIC TEST TIME/DATE RESET PROG. VALUE [2] / [2] [2] / [3] [2] / [4] [2] / [5] [2] / [6] [2] / [7] [2] / [8] [2] / [9] [2] / [10] [2]/[11] [2] / [12] [2] / [ BYP] [2] / [ MEM] [2] / [ TRBL] [3]/[2 ND] [3] / [1] [3] / [2] [3] / [3] [3] / [4] [3] / [5] [3] / [6] [3] / [7] [3] / [8] [3] / [9] [3] / [10] [3]/[11] [3] / [12] [3] / [ BYP] [3] / [ MEM] [3] / [ TRBL] [4]/[2 ND] [4] / [1] [4] / [2] For addresses 044 to 126, see pages 7 to

4 REPORTING CODES: (reset code = empty" [2 ND] [2 ND] ) All digits from [1] to [F] are valid. Entering [2 ND] = digit will not be reported except for contact I.D. programmable codes. For single digit reporting enter "skip" ([2 ND] ) as first digit. If CTACT I.D. format (all codes) is selected, addresses 300 to 527 (s 11 to 67) do not have to be programmed. (Select Contact I.D (all codes) - key [10] for both central station numbers at 09 - address 038.) ARMING (closing) CODES: Data Description Address Data Description Address 11 Auto / Espload Master User code 1 User code User code 27 User code 28 User code 29 User code User code 3 User code 4 User code 5 User code User code 31 User code 32 User code 33 User code User code 7 User code 8 User code 9 User code User code 35 User code 36 User code 37 User code User code 11 User code 12 User code 13 User code User code 39 User code 40 User code 41 User code User code 15 User code 16 User code 17 User code User code 43 User code 44 User code 45 User code User code 19 User code 20 User code 21 User code See next page User code 47 User code 48 / (Duress) User code 23 User code 24 User code 25 User code

5 REPORTING CODES: (reset code "empty") DISARMING 23 (opening) CODES: Data Description See previous page Espload Master Address Data Description User code 25 User code 26 User code 27 User code 28 Address User code 1 User code 2 User code 3 User code User code 29 User code 30 User code 31 User code User code 5 User code 6 User code 7 User code User code 33 User code 34 User code 35 User code User code 9 User code 10 User code 11 User code User code 37 User code 38 User code 39 User code User code 13 User code 14 User code 15 User code User code 41 User code 42 User code 43 User code User code 17 User code 18 User code 19 User code 20 User code 21 User code 22 User code 23 User code User code 45 User code 46 User code 47 User code 48 / (Duress) ALARM CODES ZE 1 TO 12: Data Description 36 Zone 1 Zone 2 Zone 3 (fire) Zone 4 Address (see add. 100) 403 ALARM CODES ZE 13 TO 24: Data Description 39 Zone 13 Zone 14 Address Zone 5 Zone 6 Zone 7 Zone Zone 9 Zone 10 Zone 11 Zone

6 REPORTING CODES: (reset code "empty") ZE 1 TO 12 RESTORE CODES: Data Description 42 Zone 1 Zone 2 Zone 3 (fire) Zone 4 Address (see add. 100) 427 ZE 13 TO 24 RESTORE CODES: Data Description Address 45 Zone 13 Zone Zone 5 Zone 6 Zone 7 Zone Zone 9 Zone 10 Zone 11 Zone ZE 1 TO 12 SHUTDOWN CODES: Data Description Address 48 Zone 1 Zone 2 Zone 3 Zone ZE 13 TO 24 SHUTDOWN CODES: Data Description Address 51 Zone 13 Zone Zone 5 Zone 6 Zone 7 Zone Zone 9 Zone 10 Zone 11 Zone TAMPER 1 TO 12 TROUBLE CODES: Data Description Address 54 Tamper 1 Tamper 2 Tamper 3 Tamper TAMPER 13 TO 24 TROUBLE CODES: Data Description Address Tamper 5 Tamper

7 DECIMAL PROGRAMMING 3 Digit Decimal Value Programming Used to program addresses 044 to 061. Values entered must contain 3 digits between "000" and "255". ([10] = 0) Decimal value programming: 1) Press [ENTER] + installer code. ([ENTER] key will flash.) 2) Enter 3 digit address (044 to 061). 3) Current value will be displayed on keypad. 4) Enter 3 digit DECIMAL value. 5) Repeat from step 2 onward for next address. To exit programming mode press [CLEAR]. 044: / (hours) Auto arm time (between "000" and "023") 045: / (minutes) Auto arm time (between "000" and "059") 046: / (days) Auto test report every? days (between "001" and "255") (000 = disabled) 047: / (hours) Auto test report (between "000" and "023") 048: / (minutes) Auto test report (between "000" and "059") - 7 -

8 DECIMAL PROGRAMMING 049: / (seconds) Exit delay (factory default 60 seconds) 050: / (seconds) Entry delay 1 (factory default 45 seconds) 051: / (seconds) Entry delay 2 (factory default 45 seconds) 052: / (minutes) Bell cut-off time (factory default 5 minutes) 053: / ( x 15 msec.) Zone speed (factory default 600 msec.) 054: / (minutes) Power failure report delay (factory default 30 minutes) (000 = disabled) 055: / ( x 15 minutes) "No movement" report time (factory default 8 hours) (000 = disabled) 056: / PGM timer setting (001 to 127 for seconds and 129 to 255 for minutes) (factory default 5 seconds) Add 128 to desired value in minutes (i.e. for 5 minutes: enter = 133) 057: / Intellizone delay (in seconds, minimum = 10 seconds) (factory default 48 seconds) 058: / Installer code lock (147 = locked, 000 = unlocked) 059: / (seconds) Programmable delay before alarm transmission (5 to 63 seconds) (000 = disabled) 060: / (seconds) Recent closing delay (000 = disabled) 061: / Future Use FEATURE SELECT PROGRAMMING Addresses ""/"OFF" status of the key lights determines feature selection. In programming mode, enter 3 digit memory address (062 to 126). To save entries, press [ENTER]. To exit programming mode press [CLEAR]. Reset = OFF for addresses 062 to 126. Addresses 080 to 085 for future use

9 FEATURE SELECT PROGRAMMING (continued) (On/off status of key lights determines which feature is selected.) 086: See "TLM" table PS1/Keyswitch = regular arm PS1/keyswitch arming Call back Auto arm on time Auto arm on no movement Pulse dialing Partitioning Silent zone/panic generates a silent alarm (1:2) Pulse Europe See "Reporting" table Bell squawk on arm/disarm Auto zone shutdown KEY OFF / [2 ND] [1] [2] stay arm / System A [3] [4] [5] [6] [7] Tone dialing (DTMF) [8] [9] generates only a report [10] (1:1.5) Pulse USA [11] [12] [ BYP] [ MEM] [ TRBL] 088: KEY OFF / Automatic event buffer transmission [2 ND] Panic 1 (keys [1] & Panic 2 (keys [4] & [3], PS1) [6]) [1] [2] Panic 3 (keys [7] & [9] ) [3] Panic 1 silent (PS1) [4] audible Panic 2 silent [5] audible Panic 3 silent Key [10] regular arm Key [11] stay or system A arm 6 digit access codes Tamper Recognition [6] [7] [8] [9] [10] [11] fire 4 digit Beep on exit delay Report zone restore on bell cut-off [12] [ BYP] on zone closure Zones with EOL (1K ) [ MEM] no EOL Always report disarm [ TRBL] only after alarm 090: Exclude power failure from trouble display Zone 9 Auto arm = regular arm No tamper bypass Zone doubling (ATZ) Audible trouble warning Duress Keypad 1 zone supervision Keypad 2 zone supervision KEY OFF / [2 ND] [ BYP] [ MEM] [ TRBL] TELEPHE LINE MITOR Address 086, Key [2 ND] [1] OFF OFF OFF OFF KEY [2 ND ] [1] OFF OFF OFF OFF TLM disabled TLM generates trouble only generates an alarm if armed silent alarm becomes audible (address 086, key [9] has to be OFF) REPORTING OPTIS Address 086, Key [11] [12] * KEY TYPE DIALING SEQUENCE (tel. No.) [11] [12] Reporting disabled Regular reporting Split reporting: Alarms System report Double reporting * 1,2,1,2,1,2,1,2, fail to comm. 1,1,1,1,1,1,1,1, fail to comm. 2,2,2,2,2,2,2,2, fail to comm. 1,1,1,1,1,1,1,1, fail to comm., 2,2,2,2,2,2,2,2, fail to comm. On alarm, all reports are made to Tel. #1 until system is disarmed. (Once disarmed, system reports are made to Tel. #2) TAMPER / WIRE FAULT DEFINITIS SYSTEM ARMED Alarm as per individual zone definitions Always generate trouble and alarm, audible or silent as per individual zone definitions * ** [1] disabled (in case of fire zone 3 only) [2] stay / System A [3] [4] [5] [6] tamper follows zone bypass definition [7] [8] [9] [10] [11] [12] Address 088, Key [10] [11] Exception: for 24 hour zones the tamper definition will follow the audible/silent alarm definition of the 24 hour zone. Silent zones will generate a silent alarm. 1.1 PS1 software version Keypad software versions prior to KEY [10] [11] OFF OFF OFF 4.0 } } PS1 software versions onward Keypad software versions onward OFF SYSTEM DISARMED * Tamper supervision disabled No alarm, trouble code reported Silent alarm. Trouble and alarm codes reported Audible alarm. Trouble and alarm codes reported Keypad supervision must be OFF Keypad supervision must be ** (See Wiring Diagram) -9-

10 Note: Do not use the Intellizone feature and an entry delay for the same zone, otherwise an alarm may occur as a user tries to disarm the system. KEY ACCESS PROGRAMMING Programs features quickly, without entering addresses or numbers. To activate key access programming, press [ENTER], followed by installer, master or user code 1. (Code required depends on the feature you wish to access - see below.) Press the key corresponding to the desired feature. Press [ENTER] or [CLEAR] to exit. key [8] Installer test mode (installer code only) In installer test mode, a confirmation beep (intermittent) indicates test is "on", a "rejection" beep (long) indicates test is "off". The bell will squawk during walk testing to indicate opened, functional zones. [9] "Auto arming" time program (all 3 codes) Key [9] flashes. Enter two digits (00 to 23) for hours + 2 digits (00 to 59) for minutes. [MEM] "Panel time" and clear "trouble 8" (all 3 codes) Key [MEM] flashes. Enter two digits (00 to 23) for hours + 2 digits (00 to 59) for minutes. [BYP] Test report (all 3 codes) Reporting is at address 086, keys [11], [12]. A value must be entered at address 512, and both telephone and account numbers must be programmed. [TRBL] Call Espload via telephone (all 3 codes) Panel identifier and PC password (addresses ) and computer telephone number (addresses ) must be programmed. [AWAY] Answer Espload (all 3 codes) This feature is available when using the ADP-1 adapter. In Espload, "blind dial" must be activated in "modem setup", and panel phone number programmed (works also without ADP-1). [STAY] Cancel communication attempts Until next reportable event (master code and user 1 can only stop calls to Espload) (installer code - all communications) When communicating with Espload, it is impossible to enter programming mode

11 ESPRIT 738 CNECTI DIAGRAMS The system hardware will recognize the following zone conditions: Note: Keypad zones always use (1K OHM) EOL resistor. SINGLE ZE CNECTIS ZE connection, without EOL resistor (N.C. contacts) address 088, key [MEM] = "on" key [10] = "off" (reset) key [11] = "off" (reset) address 090, key [8] = "off" N.C. contacts see Figure 1 ZE connection, with EOL resistor (N.C. and N.O. contacts) address 088, key [MEM] = "off" (reset) key [10] = "off" (reset) key [11] = "off" (reset) address 090, key [8] = "off" N.C. and/or N.O. contacts, see Figure 2 ZE connection, without EOL resistor, with tamper recognition (N.C. contacts) address 088, key [MEM] = "on" key [10] = See "Tamper/wire Fault Definitions key [11] = and Options" address 090, key [8] = "off" Tamper transmits separate code, see Figure 3 ZE connection, with EOL resistor, with tamper recognition, and with wire fault (short circuit) recognition (N.C. contacts) address 088, key [MEM] = "off" key [10] = See "Tamper/wire Fault Definitions key [11] = and Options" address 090, key [8] = "off" Tamper/wire fault transmits separate code, see Figure 4 ADVANCED TECHNOLOGY ZE CNECTIS (2 zones / input) 2 ZES connection, without EOL resistor (N.C. contacts) address 088, key [MEM] = "on" key [10] = "off" key [11] = "off" address 090, key [8] = "on" Each zone transmits a separate alarm code, see Figure

12 ESPRIT 738 CNECTI DIAGRAMS 2 ZES connection, without EOL resistor, with tamper recognition (N.C. contacts) address 088, key [MEM] = "on" key [10] = See "Tamper/wire Fault Definitions key [11] = and Options" address 090, key [8] = "on" Tamper transmits separate code Each zone transmits separate alarm code, see Figure

13 ESPRIT 738 CNECTI DIAGRAMS 2 ZES connection, with EOL resistor, with tamper recognition, and with wire fault (short circuit) recognition (N.C. contacts) address 088, key [MEM] = "off" key [10] = See "Tamper/wire Fault Definitions key [11] = and Options" address 090, key [8] = "on" Each zone transmits a separate alarm code. Tamper/wire fault transmits a separate alarm code, see Figure

14 ESPRIT 738 WIRING DIAGRAM Caution: Disconnect battery before replacing fuse. (every 60 seconds) Service Keypad + AUX - GRN YEL BATT 5 AMP RESET JUMPER PARADOX SECURITY SYSTEMS ESPRIT 738 SERIAL OUTPUT DIALER - + BLACK RECHARGEABLE BATTERY RED BATT BELL RELAY OPTI UL/ULC 12VDC / 7AH To cabinet and grounding rod UL: K12 model T16 V4O ULC: Frost model FTC 1637 Warning: Improper connection may result in damage to the system. TRANSFO 16.5VAC 40VA A.C. POWER will shut down if current exceeds 3A. BELL SIREN UL/ULC Wheelock 46T-12 SERVICE KEYPAD /7 2/8 3/9 4/10 5/11 6/12 T-1 N.O. contacts YEL GRN BLK RED 1K EOL Smoke and heat detectors AUX POWER 400mA max. 250mA max. for 24 hr. standby. To connect additional wiring to auxiliary power, use the red (+) and black (-) keypad connectors. Aux power will shut down if current exceeds 1A. R-1 RING TIP GRY BRN RED GRN Warning: Disconnect telephone line before servicing. RJ31X CA 38A Address 100 * Zone 3 = Fire zone if zone definition is "24 hour". * Keypad 1or2 N.O. 1K EOL N.C. * PS1 software version 1.1 Keypad software versions prior to 4.0 Keypad supervision must be OFF PS1 software versions 2.0 onward Keypad software versions 4.0 onward } } Keypad supervision must be (See Address 090, key [11] [12]) N.O. Keypad 1or2 1K EOL N.C. P R RMED RE DY DOX MAX 5 per system PS1 1K EOL KEYPAD 639/640 MAX 2 per system The 640 keypad can be used with the panels but will not display correct event list codes. N.C. N.C. Keypad 1 Keypad 2 KEYPAD 616/626/633 MAX 5 per system For resistor values, refer to 639/640 installation manuals. FIRE RESET To program PGM1 to conduct 4 second smoke detector reset when [ CLEAR] and [ ENTER] are pressed simultaneously: Address 039 = [ BYP] (first digit) Address 042 = [2 ND] [6] Address 040 = [5] [10] Address 056 = [10] [10] [4] Keyswitch can be used in parallel with keypad (Not on UL systems). KEYSWITCH CNECTI KYPD GRN KEYSWITCH KYPD BLK FIRE ALARM ZE CNECTIS * PGM maximum 50mA GROUND START CIRCUIT PGM OUTPUT RELAY * PGM + AUX Smoke detector + - Z3 COM WHT BLK PGM RED +AUX Smoke detector + - WHT BLK PGM RED +AUX MR3-UL MR3-UL Smoke detector power supervision relay, 12VDC 1K EOL Smoke detector must be 4 wire latching - UL Falcon model 5454, ULC BRK Power supervision relay model MR3-UL. RNG Not permitted on UL listed systems YEL COM BRN N.C. N.O. YEL SECURITY SYSTEMS 780 Industrial Blvd., St-Eustache, Montreal, Quebec, Canada J7R 5V3 Fax: (514) Paradox Security Systems Graphic Dept PRINTED IN CANADA

HEXA PROGRAMMING: STREAMLINED SECTION PROGRAMMING

HEXA PROGRAMMING: STREAMLINED SECTION PROGRAMMING -961212-0004 SOFTWARE VERSION 3.10 CONTROL PANEL RESET: Installer lock must be unlocked. ( 058: enter any value other than 147) Power down reset (1) Remove battery and AC to power down the unit. (2) Connect

More information

SOFTWARE VERSION 2.20 CONTROL PANEL RESET: Installer lock must be unlocked. (Address 255: enter any value other than 147)

SOFTWARE VERSION 2.20 CONTROL PANEL RESET: Installer lock must be unlocked. (Address 255: enter any value other than 147) -961112-0003 SOFTWARE VERSI 2.20 CTROL PANEL RESET: Installer lock must be unlocked. ( 255: enter any value other than 147) Power down reset (1) Remove battery and AC to power down the unit. (4) Wait 3

More information

SOFTWARE VERSION 2.20 CONTROL PANEL RESET:

SOFTWARE VERSION 2.20 CONTROL PANEL RESET: -961112-0002 SOFTWARE VERSI 2.20 CTROL PANEL RESET: Installer lock must be unlocked. ( 255: enter any value other than 147) Power down reset (1) Remove battery and AC to power down the unit. (4) Wait 3

More information

HEXA PROGRAMMING: STREAMLINED SECTION PROGRAMMING

HEXA PROGRAMMING: STREAMLINED SECTION PROGRAMMING 48ESEP-01 SOFTWARE VERSION 3.10 CONTROL PANEL RESET: Installer lock must be unlocked. (Address 058: enter any value other than 147) Power down reset (1) Remove battery and AC to power down the unit. (2)

More information

System Programming Guide

System Programming Guide & System Programming Guide Software Versions 4.4 (728ULT) and 4.1 (738ULT) Installer Code (Default - 728 Ultra: 282828; 738 Ultra: 383838) Full access to programming, except user access codes (PINs). No

More information

0$(6752 0$(6752. Programming Guide. 6 and 10 Zone Alarm Control Panel ,1752'8&7,21 +(;$ 352*5$00,1* 675($0/,1(' 6(&7,21 352*5$00,1* FIGURE 1 FIGURE 2

0$(6752 0$(6752. Programming Guide. 6 and 10 Zone Alarm Control Panel ,1752'8&7,21 +(;$ 352*5$00,1* 675($0/,1(' 6(&7,21 352*5$00,1* FIGURE 1 FIGURE 2 0$(6752 0$(6752 6 and 10 Zone Alarm Control Panel Programming Guide,1752'8&7,21 The Maestro-600 and Maestro-1000 alarm control panels enable reduced number of programming steps. End-users can access most

More information

PROGRAMMING GUIDE SPECTRA CONTROL PANELS V , 1725EX, 1728 AND 1728EX 1755, 1755EX, 1758, AND 1758EX

PROGRAMMING GUIDE SPECTRA CONTROL PANELS V , 1725EX, 1728 AND 1728EX 1755, 1755EX, 1758, AND 1758EX PROGRAMMING GUIDE SPECTRA CONTROL PANELS V1.2 1725, 1725EX, 1728 AND 1728EX 1755, 1755EX, 1758, AND 1758EX TABLE OF CONTENTS HOW DO I PROGRAM THE SYSTEM?... 4 Single Digit Data Entry Method (Hexadecimal

More information

Digiplex System V2.14 / V2.2ACC. Control Panel Programming Guide

Digiplex System V2.14 / V2.2ACC. Control Panel Programming Guide Digiplex System V2.14 / V2.2ACC Control Panel Programming Guide Table of Contents Getting Started...2 What Do I Do First?...2 How Do I Program the Control Panel?...2 Single Digit Entry Method...2 Multiple

More information

All-In-One Wireless Security System V3.2 Programming Guide. Model # MG6130 / MG6160

All-In-One Wireless Security System V3.2 Programming Guide. Model # MG6130 / MG6160 All-In-One Wireless Security System V3.2 Programming Guide Model # MG6130 / MG6160 We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com

More information

EVO192 v3.0 Fire and Burglary What s New

EVO192 v3.0 Fire and Burglary What s New EVO192 v3.0 Fire and Burglary What s New Compatibility: EVO192 v3.0 TM50 v1.31 K641 v2.41 Overview: CP-01 Compliancy Wiring Diagram The following sections/options have been added to the EVO192 panel. They

More information

1728EX, 1728, 1738EX AND 1738 SYSTEM PROGRAMMING GUIDE

1728EX, 1728, 1738EX AND 1738 SYSTEM PROGRAMMING GUIDE DEFAULT INSTALLER CODE 0000 / 000000 (see section [281] on page 17) DEFAULT SYSTEM MASTER CODE 1234 / 123456 (see section [301] on page 17) HOW DO I ENTER PROGRAMMING MODE? STEP 1: Press [ENTE R] STEP

More information

RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL

RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL RANGER 8600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS GENERAL DESCRIPTION... 2 STANDARD AND OPTIONAL PARTS LIST... 2 PARTS DIAGRAM... 3 TERMINAL DRAWING AND SPECIAL NOTES...

More information

MG5000 V2.4 MG5050 V2.4 SP5500 V2.4 SP6000 V2.4 SP7000 V2.4. Programming Guide

MG5000 V2.4 MG5050 V2.4 SP5500 V2.4 SP6000 V2.4 SP7000 V2.4. Programming Guide MG5000 V2.4 MG5050 V2.4 SP5500 V2.4 SP6000 V2.4 SP7000 V2.4 Programming Guide We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com

More information

Fire Burglary Instruments Inc. XL-2G Gold Control/Communicator Installation Training Seminar Rev. 5/96

Fire Burglary Instruments Inc. XL-2G Gold Control/Communicator Installation Training Seminar Rev. 5/96 Fire Burglary Instruments Inc. XL-2G Gold Control/Communicator Installation Training Seminar Rev. 5/96 XL-2G Gold Product Overview 7 Zones (6 programmable + panic or keyswitch zone) Fast Loop Response

More information

DL150 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL

DL150 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL DL150 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS 1. GENERAL DESCRIPTION... 2 2. STANDARD AND OPTIONAL PARTS LIST... 2 3. FEATURE DEFINITIONS... 3 4. TERMINAL DRAWING AND SPECIAL

More information

RANGER 7600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL

RANGER 7600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL RANGER 7600 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS 1. TABLE OF CONTENTS... P.1 2. GENERAL DESCRIPTION... P.2... 3. STANDARD AND OPTIONAL PARTS LIST... P.2... 4. FEATURE

More information

INSTALLATION MANUAL PC56O. Version 1.OA

INSTALLATION MANUAL PC56O. Version 1.OA INSTALLATION MANUAL PC56O Version 1.OA TABLE OF CONTENTS INTRODUCTION 3 Features... 3 Specifications... 3 INSTALLATION 4 Mounting the Control Panel... 4 Mounting the Keypad... 4 Wiring... 5 Burglary Zone

More information

GEM-P800 Programming Instructions

GEM-P800 Programming Instructions NOTE After 15 minutes of keypad inactivity the keypad will emit a steady tone indicating the panel has been left in Dealer Program Mode Enter Dealer Code to exit or press the key to return to Dealer Program

More information

Digiplex Control Panel (DGP-848) - V4.0

Digiplex Control Panel (DGP-848) - V4.0 Digiplex Control Panel (DGP-848) - V4.0 DGP-848 Reference and Installation Manual TABLE OF CONTENTS INTRODUCTION... 4 1.0 1.1 Features... 4 1.2 Specifications... 4 INSTALLATION... 5 2.0 2.1 Location &

More information

636 and 646 Keypads. User s Manual

636 and 646 Keypads. User s Manual 636 and 646 Keypads 636 646 User s Manual Table Of Contents Basic Operation... 2 Access Codes... 4 Arming & Disarming... 5 Panic Zones... 11 Key Access Programming... 12 Additional Features... 13 Trouble

More information

All-In-One Wireless Security System V1.0. Model #: MG-6060

All-In-One Wireless Security System V1.0. Model #: MG-6060 All-In-One Wireless Security System V1.0 Model #: MG-6060 Reference and Installation Manual DRAFT Table of Contents Introduction... 5 About Magellan and this Manual... 5 Conventions... 5 Specifications...

More information

RANGER 8980E DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL

RANGER 8980E DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL RANGER 8980E DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS GENERAL DESCRIPTION...2 STANDARD AND OPTIONAL PARTS LIST...2 FEATURE DEFINITIONS...3 TERMINAL DRAWING AND SPECIAL NOTES...4

More information

TABLE OF CONTENTS. General Description Standard and Optional Parts List Feature Definitions Comments about the 8600E...

TABLE OF CONTENTS. General Description Standard and Optional Parts List Feature Definitions Comments about the 8600E... 5$1*(5( DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS General Description... 2 Standard and Optional Parts List... 2 Feature Definitions... 3 Comments about the 8600E... 4 Terminal

More information

Table of Contents. All-In-One Wireless Security System V1.3. Programming Guide. Model # MG-6060 / MG-6030

Table of Contents. All-In-One Wireless Security System V1.3. Programming Guide. Model # MG-6060 / MG-6030 All-In-One Wireless Security System V1.3 Programming Guide Model # MG-6060 / MG-6030 Table of Contents Things You Should Know... 2 About This Programming Guide... 2 Conventions... 2 Installer Code (Default:

More information

All-In-One Wireless Security System V1.0. Model #: MG Reference and Installation Manual

All-In-One Wireless Security System V1.0. Model #: MG Reference and Installation Manual All-In-One Wireless Security System V1.0 Model #: MG-6060 Reference and Installation Manual Table of Contents Introduction... 3 About Magellan and this Manual... 3 Conventions... 3 Specifications... 3

More information

Property of Monitronics Inc

Property of Monitronics Inc Enter Program Program Location 1. Hold 8 key for 3 seconds, keypad will beep 2. Enter 4 5 6 7 8 9, display should show dash on display 1. Press [B/A] key display will show 3 dashs 2. Enter 3-digit location

More information

TABLE OF CONTENTS TABLE OF CONTENTS 1

TABLE OF CONTENTS TABLE OF CONTENTS 1 TABLE OF CONTENTS TABLE OF CONTENTS 1 FEATURES 2 Keypad Programmable... 2 EEPROM Memory... 2 Static/Lightning Protection... 2 Supervision... 2 Operation... 2 SPECIFICATIONS 2 PC1550 Control Panel... 2

More information

TABLE OF CONTENTS. FOR THE RECORD 15 PROGRAMMING WORK SHEETS 16 CONTROL PANEL WIRING DIAGRAM inside back cover

TABLE OF CONTENTS. FOR THE RECORD 15 PROGRAMMING WORK SHEETS 16 CONTROL PANEL WIRING DIAGRAM inside back cover TABLE OF CONTENTS FEATURES 2 SPECIFICATIONS 2 INSTALLATION 3 Mounting the Panel... 3 Mounting the Keypad... 3 Auxiliary Power Connection... 3 PGM Terminal Connections... 3 Bell/Siren Connection... 3 Keypad

More information

ESPRIT 616/626 KEYPADS. User Manual P R D O X S E C U R I T Y S Y S T E M S. Model 626 READY UM ESPRIT PRINTED IN CANADA 2ND TRBL

ESPRIT 616/626 KEYPADS. User Manual P R D O X S E C U R I T Y S Y S T E M S. Model 626 READY UM ESPRIT PRINTED IN CANADA 2ND TRBL ESPRIT 616/626 KEYPADS LISTED U User Manual READY ARMED Model616 2ND TRBL MEM BYP 1 2 4 7 0 3 5 6 8 9 11 10 AWAY STAY CLEAR ENTER 12 Model 626 READY ARMED ESPRIT P R D O X S E C U R I T Y S Y S T E M S

More information

MG Partition 64-Zone Wireless Console with GPRS/GSM Version 1.6. Section Programming Guide

MG Partition 64-Zone Wireless Console with GPRS/GSM Version 1.6. Section Programming Guide MG6250 2-Partition 64-Zone Wireless Console with GPRS/GSM Version.6 Section Programming Guide Things You Need to Know About this Programming Guide The MG6250 All-in-one Wireless Console can be programmed

More information

DL100 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL

DL100 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL DL100 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS 1. GENERAL DESCRIPTION...P.2 2. STANDARD AND OPTIONAL PARTS LIST...P.2 3. FEATURE DEFINITIONS...P.3 4. TERMINAL DRAWING AND

More information

INSTALLATION MANUAL PC15OO

INSTALLATION MANUAL PC15OO INSTALLATION MANUAL PC15OO This device complies with Parts 15 and 68 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)

More information

All-In-One Wireless Security System V1.0. Model # MG Programming Guide

All-In-One Wireless Security System V1.0. Model # MG Programming Guide All-In-One Wireless Security System V1.0 Model # MG-6060 Programming Guide Things You Should Know... 4 About This Programming Guide... 4 Conventions... 4 Installer Code (Default: 0000 / 000000)... 4 Maintenance

More information

Alarm Control Panel WIC-16Z4P WIC-5Z2P. Installation & Operation User Manual

Alarm Control Panel WIC-16Z4P WIC-5Z2P. Installation & Operation User Manual WIC-16Z4P WIC-5Z2P Installation & Operation User Manual Page : 1/34 INDEX # Function Page 1 Abort Current Communication and Clear Reporting Queue (*59) 13 2 Abort Current Communications (*59) 10 3 Account

More information

ESPRIT. 616/626 KEYPADS. User Manual P R D O X. Model 626 READY S E C U R I T Y S Y S T E M S UM ESPRIT

ESPRIT.  616/626 KEYPADS. User Manual P R D O X. Model 626 READY S E C U R I T Y S Y S T E M S UM ESPRIT ESPRIT 616/626 KEYPADS BYP 1 2 4 7 0 3 5 6 8 9 11 10 AWAY CLEAR ENTER 2ND TRBL MEM STAY READY ARMED 12 User Manual Model616 ESPRIT LISTED Model 626 READY ARMED LISTED U P R D O X S E C U R I T Y S Y S

More information

INSTALLATION MANUAL & PROGRAM RECORD SHEET

INSTALLATION MANUAL & PROGRAM RECORD SHEET INSTALLATION MANUAL & PROGRAM RECORD SHEET TABLE OF DESCRIPTION CONTENTS PAGE WIRING MANUAL 2-6 MENU CHART 7 INSTALLER FUNCTIONS 8 MENU 1 SYSTEM TIMES 9 MENU 2 ZONE CONFIGURATION 10-14 MENU 3 SYSTEM OPTIONS

More information

DL-250 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL

DL-250 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL DL-250 DOWNLOADABLE CONTROL COMMUNICATOR INSTALLATION MANUAL TABLE OF CONTENTS 1. GENERAL DESCRIPTION...P.2 2. STANDARD AND OPTIONAL PARTS LIST...P.2 3. FEATURE DEFINITIONS...P.3 4. TERMINAL DRAWING AND

More information

INSTALLATION MANUAL PC25OO

INSTALLATION MANUAL PC25OO INSTALLATION MANUAL PC25OO NOTES ON UL INSTALLATION This equipment is UL listed in accordance with UL standard 1023 (Household Burglar Alarm System Units), UL standard 985 (Household Fire Warning Units)

More information

CC488. Quick Reference Guide Solution Ultima 880

CC488. Quick Reference Guide Solution Ultima 880 CC488 EN Quick Reference Guide Solution Ultima 880 CC488 Quick Reference Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty

More information

4-PGM Expansion Module

4-PGM Expansion Module 4-PGM Expansion Module APR3-PGM4 = Default setting SECTION [001] : General Options SECTION [002] : PGM Options Option OFF ON Option OFF ON [1] Future Use N/A N/A [1] PGM1 Deactivation After Deactivation

More information

8-zone Expansion Module

8-zone Expansion Module 8-zone Expansion Module APR3-ZX8 SECTION [001] : General Options Option OFF ON [1] Tamper Recognition ON = Input 8 (Z8) becomes tamper input = Default setting Disabled Enabled [2] PGM Deactivation After

More information

System Introduction. 1.1 Specifications

System Introduction. 1.1 Specifications System Introduction S E C T I O N 1 1.1 Specifications Downloading Software Support PC585 uses DLS-1 v6.5 and up. Flexible Zone Configuration Four fully programmable zones; system expandable to eight zones

More information

SPECIFICATIONS Control Panel Specifications Remote Keypad Specifications 21 zones including: (PC3000RK) Audible alarm output:

SPECIFICATIONS Control Panel Specifications Remote Keypad Specifications 21 zones including: (PC3000RK) Audible alarm output: SPECIFICATIONS Control Panel Specifications 21 zones including: 16 fully programmable supervised zones (EOL resistors) Supervised fire zone 1 auxiliary normally open zone 3 keypad activated zones Audible

More information

Property of Monitronics Inc

Property of Monitronics Inc Enter Program Press CODE key + * + 2468 + 1 (also try 2121) Installer Options Move to location Program location Exit Program Default Panel Hex Program Code + * + Installer Code + 1 = Enter Programming

More information

Installation Manual Premier 412/816/832. Issue 10

Installation Manual Premier 412/816/832. Issue 10 Installation Manual Premier // Issue 0 Premier // Installation Manual 5. Operating the System Introduction Before attempting to operate the alarm system ensure you have familiarised yourself with all the

More information

CC408. Quick Reference Guide Solution 880

CC408. Quick Reference Guide Solution 880 CC408 EN Quick Reference Guide Solution 880 CC408 Quick Reference Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems Pty Ltd ( Bosch

More information

Light " " = TRBL MODEL 633 KEYPAD TROUBLE DISPLAY. [7] Communicator fail to report. Fire trouble. Tamper or zone wiring fail. Telephone line monitor

Light   = TRBL MODEL 633 KEYPAD TROUBLE DISPLAY. [7] Communicator fail to report. Fire trouble. Tamper or zone wiring fail. Telephone line monitor 11 12 STAY AWAY Light " " = TRBL When " ON", indicates existence of trouble conditions. Press to view the "trouble code" display. MEM ON [1] No battery/low battery [2] Power failure [3] AC fail [4] No

More information

Quick Programmer s Manual

Quick Programmer s Manual Version 2.604 (31/03/05) p1 Quick Programmer s Manual 2005. Inner Range Pty. Ltd. Part Number: 630048V2 p2 Version 2.604 (31/03/05) TABLE OF CONTENTS. 1. PROGRAMMING FLOWCHART. The following flowchart

More information

First Alert 1200C Installer Notes M. Leuck

First Alert 1200C Installer Notes M. Leuck First Alert 2C Installer Notes M. Leuck. Programming can done by standard keypads 2. Enter programming with Installer Code + 8 + + 3. Another method of entering programming: Power system down, then back

More information

System Introduction. 1.1 Specifications S E C T I O N 1

System Introduction. 1.1 Specifications S E C T I O N 1 System Introduction S E C T I O N 1 1.1 Specifications Control Panel Specifications Flexible Zone Configuration: 8 Fully Programmable Zones 37 Access Codes: 32 User, 1 System Master, 2 Partition Master

More information

AXI LED USER MANUAL (REV. 1.0)

AXI LED USER MANUAL (REV. 1.0) Security & Home Automation System AXI LED USER MANUAL (REV. 1.0) CONTENTS PREFACE FEATURES LED KEYPAD OUTLOOK 1.0 LIGHT INDICATION 1 2 4 6 CHAPTER 1: ALARM SYSTEM CONTROL 1.0 USING LED KEYPAD 1.0.1 ARMING

More information

System Introduction. 1.1 PC5015 Specifications S E C T I O N 1

System Introduction. 1.1 PC5015 Specifications S E C T I O N 1 1.1 PC5015 Specifications System Introduction S E C T I O N 1 Flexible Zone Configuration: 8 Fully Programmable Zones 38 Access Codes: 32 User, 1 System Master, 2 Partition Master, 2 Duress and 1 maintenance

More information

System Introduction. Digital Communicator Specifications: Supports all Major Formats including SIA and Contact ID Event Initiated Personal Paging

System Introduction. Digital Communicator Specifications: Supports all Major Formats including SIA and Contact ID Event Initiated Personal Paging 1.1 Specifications System Introduction S E C T I O N 1 Control Panel Specifications Flexible Zone Configuration: 8 Fully Programmable Zones 38 Access Codes: 32 User, 1 System Master, 2 Partition Master,

More information

GEM-P800. Control Panel/Communicator. Installation Instructions

GEM-P800. Control Panel/Communicator. Installation Instructions GEM-P800 Control Panel/Communicator Installation Instructions NAPCO 2002 WI850C 9/02 WI850C GEM-P800 Installation Instructions Table of Contents General Information GEM-P800 Features General Information...

More information

Radionics D4112 Program Sheet

Radionics D4112 Program Sheet Programming only by downloading, 5200 Programmer or 5100 "Wand" Programmer Plug programmer in and momentarily short Reset Pin to Terminal 25 to enable program mode 1. Account Account # I I I I I (0 to

More information

10-Zone Spectra LED Keypads

10-Zone Spectra LED Keypads 10-Zone Spectra LED Keypads User s Guide TABLE OF CONTENTS Introduction... 5 Basic Operation... 6 Auditory Feedback... 6 Keypad Indicator Lights... 8 Zone Display... 8 Alarm Memory Display... 8 Trouble

More information

Programming Worksheets

Programming Worksheets WARNING This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully

More information

Control/Communicator Installation Manual

Control/Communicator Installation Manual DAS NETWORX NX-12 Control/Communicator Installation Manual General Description...2 Ordering Information...2 Option Definitions...3 Programming the LED Code Pads...5 Programming the NX-12...9 Types of Programming

More information

Paradox Security System Graphic Dept - PRINTED IN CANADA. keypad entries in memory. arming permits movement in pre-selected,

Paradox Security System Graphic Dept - PRINTED IN CANADA. keypad entries in memory. arming permits movement in pre-selected, 970213-0001 ESPRIT 727 U LISTED User Manual VERSION 3.3 P R D O X S E C U R I T Y S Y S T E M S Paradox Security System Graphic Dept - PRINTED IN CANADA READY The green LED must be " on", indicating all

More information

Digiplex LED Keypads User s Manual

Digiplex LED Keypads User s Manual KLEDEU03.fm Page -1 Friday, May 4, 2001 11:25 AM Digiplex LED Keypads User s Manual KLEDEU03.fm Page 0 Friday, May 4, 2001 11:25 AM KLEDEU03.fm Page 1 Friday, May 4, 2001 11:25 AM TABLE OF CONTENTS 1.0

More information

642 LCD Keypad. User Manual

642 LCD Keypad. User Manual 642 LCD Keypad User Manual Table of Contents Introduction...1 Legend... 1 Basic Operation...2 Keypad Indicator Lights... 2 Visual Feedback... 2 Auditory Feedback... 3 Info List... 4 Access Codes...5 User

More information

Content. 1. Introduction to the IDS Features Installation and Wiring End-of-Line Resistors/Tamper per Zone...

Content. 1. Introduction to the IDS Features Installation and Wiring End-of-Line Resistors/Tamper per Zone... 1 2 Content 1. Introduction to the IDS 805... 7 1.1 Features...7 2. Installation and Wiring...8 3. End-of-Line Resistors/Tamper per Zone...9 4. Connecting the Telephone Communicator...10 5. Programmable

More information

HA-263K HA-263D. OWNER'S MANUAL Installation And Operation 8-ZONE ALARM CONTROL PANEL FOR HOME AND OFFICE PROTECTIONS OPEN THE CABINET FOR SERVICE

HA-263K HA-263D. OWNER'S MANUAL Installation And Operation 8-ZONE ALARM CONTROL PANEL FOR HOME AND OFFICE PROTECTIONS OPEN THE CABINET FOR SERVICE D (OPERATION) INITIATE A DYNAMIC BATTERY TEST The system tests the back-up battery once every 24 hours. The owner can initiate a dynamic battery test at any time with the following codes while the system

More information

MG5000 MG5050 SP5500 SP6000 SP7000. User Guide

MG5000 MG5050 SP5500 SP6000 SP7000. User Guide MG5000 MG5050 SP5500 SP6000 SP7000 User Guide We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us your comments.

More information

INTRODUCTION. The use of any power source other than a PC4204 to repower the Combus will result in a system malfunction.

INTRODUCTION. The use of any power source other than a PC4204 to repower the Combus will result in a system malfunction. INTRODUCTION The PC4020 is a highly flexible and versatile control which will enable the installer to meet the most demanding security requirements. The heart of the system is the main control panel, designated

More information

32-Zone Wireless Transceiver Control Panel MG5000. User s Guide

32-Zone Wireless Transceiver Control Panel MG5000. User s Guide 32-Zone Wireless Transceiver Control Panel MG5000 MG32LED MG32LRF MG10LEDH MG10LEDV User s Guide We hope this product performs to your complete satisfaction. Should you have any questions or comments,

More information

Installation Instructions

Installation Instructions g 466-2339A October 2009 2009 GE Security, Inc. Introduction This is the GE. Installations should only be done by trained professionals. Use this document to install the system with default settings that

More information

INSTALLATION MANUAL. PC3OOO Version 7.6W

INSTALLATION MANUAL. PC3OOO Version 7.6W INSTALLATION MANUAL This device complies with Parts 15 and 68 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

More information

EasyLoader. Integrated Alarm Control/Communicator. Year 2000 ready. Express Installation and Operation Manual. Edition II

EasyLoader. Integrated Alarm Control/Communicator. Year 2000 ready. Express Installation and Operation Manual. Edition II EasyLoader AV-2004, AV-2048 Integrated Alarm Control/Communicator Year 2000 ready Express Installation and Operation Manual Version 3.06 (with very slow zone) Edition II This product is subject to continual

More information

EasyLoader AV-2004, AV Integrated Alarm Control/Communicator. Year 2000 ready. Express Installation and Operation Manual. Version 2.

EasyLoader AV-2004, AV Integrated Alarm Control/Communicator. Year 2000 ready. Express Installation and Operation Manual. Version 2. EasyLoader AV-2004, AV-2048 Integrated Alarm Control/Communicator Year 2000 ready Express Installation and Operation Manual Version 2.17 Edition II This product is subject to continual enhancement and

More information

Installation Manual IMPORTANT. PC5020 Version 3.1 DLS-3 v1.3 and higher

Installation Manual IMPORTANT. PC5020 Version 3.1 DLS-3 v1.3 and higher IMPORTANT WARNING:This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be

More information

SHORT CIRCUIT ISOLATOR TO NEXT COMPONENT REQUIRING POWER TO NEXT KEYPAD (** IF REQUIRED) STROBE RELAY MODULE KEYSWITCH ISOLATION MODULE STROBE

SHORT CIRCUIT ISOLATOR TO NEXT COMPONENT REQUIRING POWER TO NEXT KEYPAD (** IF REQUIRED) STROBE RELAY MODULE KEYSWITCH ISOLATION MODULE STROBE The Door Switch 11772 Westline Industrial Drive St. Louis, Mo 63146 (877) 998-5625 www.thedoorswitch.com Patent No. RE42,991 and RE44,039 CONTROL PANEL TRANSFORMER (SUPPLIED WITH CONTROL PANEL) NOTIFICATION

More information

Version 1.03 January-2002 USER S MANUAL

Version 1.03 January-2002 USER S MANUAL Version 1.03 January-2002 1 USER S MANUAL 2 Version 1.03 January-2002 System Details CUSTOMER:...... PHONE:... FAX:... INSTALLED BY:...... PHONE:... FAX:... MAINTENANCE & SERVICE:...... PHONE:... FAX:...

More information

D6500 reports are shown in typewriter style letters. For example, AC FAILED indicates the report sent when the panel reports an AC power failure.

D6500 reports are shown in typewriter style letters. For example, AC FAILED indicates the report sent when the panel reports an AC power failure. Notice The material and instructions covered in this manual have been carefully checked for accuracy and are presumed to be reliable. However, Radionics, Inc. assumes no responsibility for inaccuracies

More information

LCD and 16-Zone LED Keypads. User s Manual

LCD and 16-Zone LED Keypads.   User s Manual LCD and 16-Zone LED Keypads 1689 1641 16-Zone LED Keypad LCD Keypad User s Manual TABLE OF CONTENTS 1.0 INTRODUCTION...3 2.0 BASIC OPERATION...4 2.1 Keypad Indicator Lights... 4 2.2 Visual Feedback...

More information

Contact ID as of 2/2/2015

Contact ID as of 2/2/2015 Contact ID as of 2/2/2015 100 Medical Zone A non-specific medical exists 101 Personal Emergency Zone Emergency Assistance request 102 Fail to report in Zone A user has failed to activate a monitoring device

More information

ELECTRONICS LINE S TECHNICAL SUPPORT DEPARTMENT: (972)

ELECTRONICS LINE S TECHNICAL SUPPORT DEPARTMENT: (972) Summit 3208GLD Installation, Operation and Programming Electronics Line (E.L.) Ltd. www.elecline.com ELECTRONICS LINE S TECHNICAL SUPPORT DEPARTMENT: (972)-3-9211110 Electronics Line (E.L.) Ltd. reserves

More information

System Manual W A R N I N G. PC6O1O Software Version 2.1

System Manual W A R N I N G. PC6O1O Software Version 2.1 System Manual W A R N I N G This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual

More information

NX-4V2 Control Panel Installation Instructions

NX-4V2 Control Panel Installation Instructions 4V2 Control Panel Installation Instructions Introduction This is the 4V2-Control Panel Installation Instructions. Installations should only be done by trained professionals. Use this document to install

More information

CONTACT ID REPORT CODES

CONTACT ID REPORT CODES CONTACT ID REPORT CODES PREFIX - E - ACTIVATION PREFIX - R - RESTORAL 100 Medical Zone 101 Personal Emergency Zone 102 Fail to report in Zone Fire Alarms 110 110 Fire Zone 111 Smoke Zone 112 Combustion

More information

Control Panel ICP-SOL2-P/ICP-SOL3-P. en User's Guide

Control Panel ICP-SOL2-P/ICP-SOL3-P. en User's Guide Control Panel ICP-SOL2-P/ICP-SOL3-P en User's Guide Control Panel Table of Contents en 3 Table of contents 1 Introduction 5 2 Specifications 6 3 Codepad Introduction 7 3.1 Codepad 7 3.2 Quick Codepad

More information

(31/03/05) Version p1. INNER RANGE IQ. Programmer s Manual. Programmer s Manual Inner Range Pty. Ltd. Part Number:

(31/03/05) Version p1. INNER RANGE IQ. Programmer s Manual. Programmer s Manual Inner Range Pty. Ltd. Part Number: (31/03/05) Version 2.604 p1 Programmer s Manual 2005. Inner Range Pty. Ltd. Part Number: 630047 p2 Version 2.604 (31/03/05) TABLE OF CONTENTS. Programming Methods... 3 1. Introduction 1.1 System Overview...

More information

Solution 862 Installation Manual ISSUE 1.30

Solution 862 Installation Manual ISSUE 1.30 Solution 862 Installation Manual ISSUE 1.30 MA406I This page has been included for you to cut out and insert into the spine of the folder Solution 862 Installation Manual ISSUE 1.30 (61-2) 9672 1233 Solution

More information

2000 Series. Program Entry Guide. Control Panels

2000 Series. Program Entry Guide. Control Panels 2000 Series EN Program Entry Guide Control Panels 2000 Series Program Entry Guide About This Manual EN 2 About This Manual This guide describes the programming parameters available to the 2000 Series Control

More information

USER CODES. User Codes (1-6 digits) Access Levels + Access Levels. Time Control Address Address Address Address User 1 (Master)

USER CODES. User Codes (1-6 digits) Access Levels + Access Levels. Time Control Address Address Address Address User 1 (Master) User Codes (1-6 digits) Access Levels Access Levels + Time Control User 1 (Master) 1 1 2 3 25 49 73 0 User 2 2 26 50 74 0 User 3 3 27 51 75 0 User 4 4 28 52 76 0 User 5 5 29 53 77 0 User 6 6 30 54 78 0

More information

Digiplex LED Keypads. User s Manual

Digiplex LED Keypads. User s Manual Digiplex LED Keypads User s Manual TABLE OF CONTENTS INTRODUCTION... 6 1.1 Legend...6 BASIC OPERATION... 7 2.1 Auditory Feedback (Beep Tones)...8 2.2 Keypad Indicator Lights...8 2.3 LED Keypads...8 2.4

More information

Control Panel ICP-SOL2-P/ICP-SOL3-P. en User's Guide

Control Panel ICP-SOL2-P/ICP-SOL3-P. en User's Guide Control Panel ICP-SOL2-P/ICP-SOL3-P en User's Guide Control Panel Table of Contents en 3 Table of contents 1 Introduction 5 2 Specifications 6 3 Codepad Introduction 7 3.1 Codepad 7 3.2 Quick Codepad

More information

DSC Power832/PC5010 Wiring the MN01-4G Cellular Communicator and Programming the Panel

DSC Power832/PC5010 Wiring the MN01-4G Cellular Communicator and Programming the Panel DSC Power832/PC5010 Wiring the MN01-4G Cellular Communicator and Programming the Panel CAUTION: It is advised that an experienced alarm installer programs the panel as further programming may be required

More information

NetworX Series NX-6 CONTROL PANEL. Installation and Startup

NetworX Series NX-6 CONTROL PANEL. Installation and Startup NetworX Series NX-6 CONTROL PANEL Installation and Startup 25 GE Security All rights reserved. These instructions do not purport to cover all details or variations in equipment nor to provide every possible

More information

P Zone Expandable Hybrid Security System

P Zone Expandable Hybrid Security System Page 1 of 11 up to 8 hardwired keypads and 4 wireless keypads 4 hardwired keypads available with zone input PWLS910 wireless handheld keypad added wireless control is provided by - PWLS908 wireless panic

More information

User Guide MG5000 MG5050 SP5500 SP6000 SP7000

User Guide MG5000 MG5050 SP5500 SP6000 SP7000 MG5000 MG5050 SP5500 SP6000 SP7000 User Guide We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www.paradox.com and send us your comments.

More information

INSTALLATION MANUAL DV8OOO. Software Version 1.0

INSTALLATION MANUAL DV8OOO. Software Version 1.0 INSTALLATION MANUAL DV8OOO Software Version 1.0 *DVACS is a registered trade mark of Electro Arts Limited and covers a wide variety of products. Full DVACS compatability applies only when the Sur-Gard

More information

VAP304 PRO INSTALLATION & OPERATION MANUAL

VAP304 PRO INSTALLATION & OPERATION MANUAL VAP304 PRO INSTALLATION & OPERATION MANUAL Panic Fire Duress Program Bypass Report Chime Test Memory B A D C Program Chime Panic Duress Exit Fire Report Bypass Memory Test Reset Password Exit Reset Password

More information

NetworX Series NX-4V2 Control Panel Installation and Startup

NetworX Series NX-4V2 Control Panel Installation and Startup NetworX Series NX-4V2 Control Panel Installation and Startup 2005 GE Security All rights reserved. These instructions do not purport to cover all details or variations in equipment nor to provide every

More information

Always Armed, Never Disarmed User Guide

Always Armed, Never Disarmed User Guide 32-Zone Security System Always Armed, Never Disarmed User Guide User Settings For security reasons, write only the user s name and not their user code. 4-Digit Codes 6-Digit Codes User # and Name Byp*

More information

MODEL 5104B. Installation and Operation Manual. Fire Communicator. Part Number E, 09/04

MODEL 5104B. Installation and Operation Manual. Fire Communicator. Part Number E, 09/04 MODEL 5104B Fire Communicator Installation and Operation Manual Part Number 151053 E, 09/04 Content Section 1 Introduction... 1-1 1.1 Feature... 1-1 1.2 Accessory Devices... 1-2 1.3 About This Manual...

More information

SECURITY SYSTEM 4110DL. Programming Form Programming Form Programming Form 4110DL-PRV3 10/96

SECURITY SYSTEM 4110DL. Programming Form Programming Form Programming Form 4110DL-PRV3 10/96 SECURITY SYSTEM 4110DL Programming Form Programming Form Programming Form 4110DL-PRV3 10/96 4110DL PROGRAMMING FORM FIELD FUNCTION [ ] = Default Value SYSTEM OPTIONS (*20-*28) *20 MASTER SECURITY CODE

More information

Master Code Arming Auto-Bypass Option - Home-Away Arming Entry Delay Off Arming

Master Code Arming Auto-Bypass Option - Home-Away Arming Entry Delay Off Arming Master Code The 4 digit Master Code is used for arming and disarming the system, for programming additional access codes, and for changing other features. The Master Code will be supplied to you by your

More information

Control Panels. Control Panels for Commercial Applications. Control panels provide the central processing

Control Panels. Control Panels for Commercial Applications. Control panels provide the central processing Control Panels Control Panels for Commercial Applications Control panels provide the central processing and logic for an integrated system. In a typical system, there are four major functions: inputs,

More information

ICP-CC408 ICP-CC408 EN. Control Panel. User s Guide

ICP-CC408 ICP-CC408 EN. Control Panel. User s Guide ICP-CC408 EN User s Guide ICP-CC408 Control Panel ICP-CC408 User's Guide Notices EN 2 Copyright Notice Unless otherwise indicated, this publication is the copyright of Bosch Security Systems, Inc, ( Bosch

More information