Property of Monitronics Inc

Size: px

Start display at page:

Download "Property of Monitronics Inc"

Roberta Lyons
5 years ago
Views:

1 Enter Program Program Location 1. Hold 8 key for 3 seconds, keypad will beep 2. Enter , display should show dash on display 1. Press [B/A] key display will show 3 dashs 2. Enter 3-digit location (use B/A for any 0) 3. Value currently programmed in location will display 4. Scroll Value UP with 4 key, scroll Value DOWN with 7, blank location with 5 5. When display shows desired Value press 2 to move to next location (Or B/A + 3-digit location to move to elsewhere) Programming with LCD layout is slightly different LCD Keypads 1 scrolls left 2 scrolls right 5 scrolls data up 9 scrolls data down Exit Program Enable Panics Lockout Bypass 1. Hold 8 key 3 seconds, keypad will flash and beep 2. Enter , display should return to normal Open Keypad cover, cute Jumper "E" (bottom left jumper, clearly marked) 1. Run jumper to pins on large chip marked X (see wiring diagram) 2. Press 9 for 3 seconds, then 8 for 3 seconds and enter LED display should show ---, remove jumper and program normallly (wire MUST be removed to view or change locations) Report Codes Zone 1 31 Duress 21 to 29 Zone 2 32 Keypad Fire Panic 19 Zone 3 33 Keypad Police Panic 29 Zone 4 34 Keypad Medical Panic 49 Zone 5 35 Low Battery 78 Zone 6 36 Low Battery Restoral 98 Zone 7 37 AC Failure 79 Zone 8 38 AC Failure Restoral 99 Zone 9 39 Fire Trouble 76 Zone Fire Restore 96 Zone Smoke Detector* 16 or 18 Zone Cancel D1 to D8 Zone Opening 5 + User Zone Closing 6 + User Zone Test/Download Complete EE Zone Zone Restores 9 + Zone IF something screws up power down then up, you have 30 seconds to get into programming

2 < Report Options > To program REPORT OPTIONS in locations 166 to 185 see below Diagram Add location together and enter sum in location Example: Enable Reporting for Zones 1 to 6, Keypad Panic, Fire, Duress, Fire Trouble, AC Fail and Low Bat 1. Press B/A then to move to Location Add ZONE 1 (1) + ZONE 2 (2) + ZONE 3 (4) + ZONE 4 (8) = 15 or F, enter the F in location Press 2 key to move to Add Zone 5 (1) + Zone 6 (2) + Keypad Panic (8) = 11 (B), enter the B in location Press 2 key to move to Add FIRE ZONE (1) + AMBUSH (2) + FIRE TROUBLE (4) = 7, enter the 7 in location Press 2 key to move to Add AC FAIL (2) + LOW BAT (4) = 6, enter the 6 in location 169 Report Enable Zone 1 to 4 I F _I Fire/Duress, Fire Trouble I 7 I Report Enable Zones 5, 6 & Panic I B _I AC Fail/Low Bat Trouble I 6 I Restores Enabled I I I Misc Restores I I I (Blank out this section) (Blank out this section) Zone Restores I I I (Blank out this section) < Report Codes > Zone 1 Report Code I 3 I 1 I Keypad Police Panic I 2 I 9 I Zone 2 Report Code I 3 I 2 I Fire Panic/Smoke Detector* I 1 I 6 I Zone 3 Report Code I 3 I 3 I Hostage/Duress I 2 I 6 I Zone 4 Report Code I 3 I 4 I Fire Trouble I 7 I 6 I Zone 5 Report Code I 3 I 5 I Day Zone Trouble I I I Zone 6 Report Code I 3 I 6 I Test Timer I I I Not Used I I I AC Failure I 7 I 9 I Low Battery I 7 I 8 I (I I I = Blank out Locations with 5 key) *Fire Panic and Smoke Detector share signal if Smoke Detector uses dedicated Fire Zone < Restore Codes > Zone 1 Restore I I I Fire Panic/Smoke I I I Zone 2 Restore I I I Not Used I I I Zone 3 Restore I I I Fire Trouble I I I Zone 4 Restore I I I Medical Panic I 4 I 9 I Zone 5 Restore I I I Not Used I I I Zone 6 Restore I I I AC Trouble Restore I I I Low Battery Restore I I I (I I I = Blank out Locations with 5 key)

3 < Opening/Closings/Cancel > Closing User 1 I I I Opening User 1 I D I 1 I Closing User 2 I I I Opening User 2 I D I 1 I Closing User 3 I I I Opening User 3 I D I 1 I Closing User 4 I I I Opening User 4 I D I 1 I Force Arm I I I (These are Cancels, see also section 179) Select User Closings I I Select User Openings I I (I I I = Blank out Locations with 5 key) < Account Numbers > Telephone Number 1 (Last 4 of Account must be entered in each section) Group 1 Account Group 2 Account Open/Close Account I? I? I? I? I I? I? I? I? I I I I I I Telephone Number 2 (Leave Blank) Group 1 Account Group 2 Account Open/Close Account I I I I I I I I I I I I I I I < Phone Numbers > Report Format Phone 1 I 9 I 2 I First Digit Second Digit Blank = Ademco/Silent Knight Slow Blank = Extended or Single Digit 1 = Sescoa, Vertex, DCI, Franklin 1 = Single Digit 2 = Radionics Fast 2 = 2-Digit (4/2) 3 = Silent Knight Fast 4 = Sumcheck 4 = Radionics, DCI, Franklin Slow 5 = Universal Hi Speed 8 = 2300 Handshake (Add this to above numbers) Receiver 1 Options I I I (Add D in 114 if delay needed to dial out) (Add 9 in 115 if 9 is needed to dial out) Receiver 1 Phone I_ E_ I I I I I I I I I I I I I I I I Report Format Phone 2 I I I (Leave blank) Receiver 2 Options I I I (Leave blank) Receiver 2 Phone I_ E_ I I I I I I I I I I I I I I I I Rings before Download I 9 I (9 rings until Answer) 269 Download Phone 1 I I I I I I I I I I I I I I I I I Download Phone 2 I I I I I I I I I I I I I I I I I

4 < Misc Functions > To program sections 084 to 216 see below Diagram Add location together and enter sum in location Example: Program Zones 1, 3 4, 5 and 6 for Door Chime 1. Press B/A then B/A again then 8 8 to enter Location Add Zone 1 (1) + Zone 2 (2) + Zone 4 (8) = 11 or B, enter B in location Press 2 key to move to Add Zone 5 (1) + Zone 6 (2) = 3, enter 3 in location 089 Swinger Shutdown I F I 3 I (Swinger enabled on all Zones) No EOL Zone Resistors I I I (F 3 = No EOL all Zones, Blank = EOL all zones) Chime Zones 1 to 6 I I I (Turns on/off chimes per zone) Never Arm I I I (Leave blank) PIR Zone I I I (Program PIR zones here. also see ) Untimed Output to Lug E15 I F I B _I I I (Normally not programmed) Keypad Sounder on Alarm I I I (Leave blank) Day Zone I I I (Leave blank) Priority Zone W/Bypass I I I (Leave blank) Priority Zone I F I 3 I (Default = F 3, leave alone) Remove Auto-Bypass I I I (Leave blank) Selective Bypass I F I 3 I (Default = F 3, leave alone) Group Bypass I? I? I (Any zone here will bypass by B/A key twice) Hr Protection I I 8 I (Use if Hold-Up buttons on a zone) Auto Reset I F I D I (Default = F D, leave alone) Entry/Exit Delay 1 Zones I? I? I (Program which zones are Delay 1) Entry/Exit Delay 2 Zones I? I? I (Program which zones are Delay 2) Interior Follower Zones I? I? I (Program PIR zones here. also see ) Abort Delay per Zone I I I (Leave blank) Burglary Output per Zone I F I B I (FB = Audible Keypad Panic, F3 = Silent) Timed Negative Output I I I (Leave blank) ms Loop Response I I I (Leave blank) ms Loop Response I I I (Leave blank)

5 Hostage/Duress Code User Program Code Installer/Dealer Code < User Codes > I 9 I 9 I I 1 I 2 I 3 I 4 I 5 I 6 I This allows customer to change User codes, leave at default I 4 I 5 I 6 I 7 I 8 I 9 I User Code 1 I 1 I 2 I 3 I 4 I User Code 2 I I I I I User Code 3 I I I I I User Code 4 I I I I I User Code 5 I I I I_ 7 I User Code 6 I I I I I User Code 7 I I I I I User Code 8 I I I I I User Codes can be 1, 2, 3 or 4 digits, If User Code 5 is Quick Arm program as 7, customer can Arm system by pressing 7, do NOT make it anything else or it will screw up other functions! < Misc Options > Add each section, place total in box (Example: = 13 or "D") I I = Blank Out with 5 key I 4 I ç 1 = Display Day Zone/Reset I 2 I ç 1 = Audible Test on Arming = Reserved = Auto-Reset after Timeout 4 = User 5 Quick Arm 4 = Reserved 8 = User 5 Report as User 1 8 = Reserved I I ç 1 = User 5 Service Code I 5 I ç 1 = Pulsing Fire = Disable Day Zone Report = Disable Key 9 Reset Fire Zone 4 = Users 6,7,8 Report as 2,3,4 4 = Enable Keypad Tactical Beeps 8 = Reserved 8 = Reset Test Timer on any Alarm Report I 1 I ç 1 = Disable Low Battery Display* I 6 I ç 1 = Disable Fault Find = Reserved = Enable Keypad Panic 4 = Disable Callback Download 4 = Enable Communicator Test 8 = Disable Function 6 Download 8 = Disable Bell Test I 1 I ç 1 = Watch on With Group Bypass I 1 I ç 1 = Display any Bypass = Chime On with Group Bypass = Reserved 4 = Display Open Zones 4 = Inc Manl Bypass in Force Arm/Status 8 = Disable Display Bypass 8 = Keyswitch Input on Zone 5 I D I ç 1 = Enable Download w/ans Machine I 6 I ç 1 = Enable User 8 to PGM Lug = Reserved = Enable PGM on E/E Delay 4 = Enable Keypad Fire Panic* 4 = Fail to Communicate on PGM Lug 8 = Enable Keypad Aux/Medical Panic* 8 = Keypad Sounder on PGM Lug I 2 I ç 1 = Touchtone Dialing I I ç 1 = Ground Start on PGM Lug = Touchtone with Rotary Backup = Armed LED on PGM Lug 4 = Backup Reporting 4 = Keypad Aux on PGM Lug 8 = Double Reporting 8 = Audio Verification on PGM Lug I 1 I ç 1 = Opening after Alarm (see 070 to 077) *Panics only work if Jumper E on Keypad is cut = Force Arm (Jumper E found at bottom left in back of Keypad) 4 = Status Report ** Panel tends to display low battery if siren sounds 8 = Split Report for any length of time

6 < System Times > Entry/Exit Times found by dividing desired time by 16 Enter 1st digit of resut in second box and 2nd digit of result in 1st box (wierd ain't it?) Sensor Watch I _I I (Leave both blank, not used) Exit Delay I C I 3 I (60 seconds) Entry Delay 1 I E I 1 I (30 seconds) Entry Delay 2 I E I 1 I (30 seconds) Burg Timeout I 6 I I (6 minutes, leave 2nd entry blank) Fire Timout I F I I (Unlimited, leave 2nd entry blank) Chime Duration I 4 I I (1/2 second Chime, leave 2nd entry blank) Abort Delay I I I (Leave both blank, not used) Test Timer I I I (Leave both blank, not used) Auto Download ID I I I (Leave both blank, not used) Callback Select I I (Leave blank, not used) 254

8 Monitronics Napco 1000e Quick Reference Guide Monitoring and Service call Arming With STATUS light steady enter User Code, ARM light should turn on indicating system is armed If display shows a flashing P system was armed with a zone open Disarming / Silencing an Alarm Instant Doors Zone Bypassing User Codes Enter 4-digit Code If silencing alarm turn off siren with User Code then hold 9 for three seconds to stop any flashing display Before or after arming system press 4 for 3 seconds STATUS light will rapidly flash and all entry doors will now be instant All zones return to normal when system is disarmed. Press [B/A] + Zone to bypass (1 to 6), BYPASS light will turn on, arm system normally When system is disarmed all bypassed Zones will return to normal. Press 8 for 3 seconds (keypad will beep) Enter User Programming Code (ARM, STATUS and BYPASS lights flash and keypad rapidly beeps) Enter User to add or change (1 to 8) Enter new 3 to 4-digit User Code When finished press [B/A] twice to exit To erase a code follow above steps but press [B/A] twice instead of entering a code Door Chimes Press 5 for 3 seconds, repeat this to turn off chimes Smoke Detector Reset Trouble Light Panic Buttons Silence siren with User Code Press 9 for 3 seconds, smoke detector should reset With any internal problem ARM, STATUS and BYPASS lights will flash and a number will appear 1 = Power Failure: System is operating on Backup Battery 2 = Low Battery: Backup Battery is low and needs to either recharge or be replaced. 3 = Failure to Communicate: System cannot communicate with Monitoring Station Press 9 and # for Fire, [*/P] and # for Police, [B/A] and # for Medical Note: You may have to arm and disarm system to turn off siren after using Panic Buttons

Property of Monitronics Inc

Property of Monitronics Inc Enter Program Press CODE key + * + 2468 + 1 (also try 2121) Installer Options Move to location Program location Exit Program Default Panel Hex Program Code + * + Installer Code + 1 = Enter Programming