AF-810 and AF-820 Venetian blinds

Transcription

1 AF-810 and AF-820 Venetian blinds Flexible. Blinds and more.

2 Flexible sun and weather protection AF-810 and AF-820 venetian blinds with flat slats AF-810 and AF-820 venetian blinds with 80 mm-wide flat slats are remarkable for their minimal package and recess, allowing tall windows and thus plenty of light. The flat, flexible slats ensure good visibility through the blind and offer increased resistance to deformation. In the AF-810 model the slats are guided at the sides by filigree chrome steel cables, whilst in the AF-820 model every other slat is guided by guide bolts on rails, alternating left and right.

3 Textured coating The innovative textured coating used for the slats demonstrates significantly better colour retention and weather resistance properties than the conventional smooth coating. Dirt adhesion is substantially reduced and the slats are easy to clean. Automated convenience Both models can be equipped with electric drives, which offer increased comfort. In conjunction with the corresponding controller, this meets the Minergie standard. Excellent materials Daylight use The blind can be split into two or three sections with different slat inclines. Open slats in the upper section enable daylight to penetrate into the depths of the room, while closed slats in the lower section serve as glare protection for the window. Flanged holes for 8 mm-wide lift tapes, Kevlar-reinforced support cords, chrome steel cable guides and slats with textured coating all ensure that the blinds will last for a long time. Range of colours Four standard colours are available to choose from, plus more than a thousand RAL, NCS and IGP colours.

4 Optional self-supporting system for AF-820 The self-supporting blind system with no mounting in the recess area preserves insulation, reduces noise transmission and prevents thermal bridges (Minergie standard). A central support is required for widths of 2400 mm or more. Protective holes The flanged holes prevent the 8 mm-wide lift tape from fraying. Not using protective plastic grommets avoids the need for premature repairs. Minimal package height Minimal package and recess height allow for tall windows and thus plenty of light. This is also an ideal solution for mounting positions with little space for sun protection.

5 Filigree cable guidance AF-810 flat slats are guided by filigree chrome steel cables 2 mm thick. Robust rail guidance AF-820 flat slats are guided by guide bolts on side rails every other slat, alternating left and right.

6 0

7 Height of opening (hl) 1501 to 1750 mm 1751 to 2000 mm 2001 to 2250 mm 2251 to 2500 mm 2501 to 2750 mm 2751 to 3000 mm 3001 to 3250 mm 3251 to 3500 mm 3501 to 3750 mm 3751 to 4000 mm 4001 to 4250 mm with cover panel Height of recess (hs) AF mm 135 mm 140 mm 150 mm 155 mm 160 mm 165 mm 170 mm 175 mm 185 mm 190 mm + 20 mm Height of recess (hs) AF mm 150 mm 155 mm 165 mm 170 mm 180 mm 185 mm 195 mm 200 mm 210 mm 215 mm + 20 mm minimum maximum 400 mm 4250 mm 400 mm 4250 mm Width of installation (bk) min. with crank drive min. with motor drive maximum 400 mm 545 mm 4500 mm 400 mm 545 mm 4500 mm Area (bk x hl) Single blinds max. with crank drive max. with motor drive coupled system max. with crank drive max. with motor drive max. coupled blinds 8 m 2 10 m 2 8 m 2 24 m 2 3 pieces 8 m 2 10 m 2 8 m 2 24 m 2 3 pieces Depth of recess (tn) minimum 120 mm 120 mm Wind resistance classes bk < 1500 mm class 5 < 76 km/h class 5 < 76 km/h bk < 2000 mm bk < 2500 mm EN bk < 3000 mm

8 Lowering In the standard model, the slats are lowered in closed position. Slat position can be adjusted at any height. Adjusting The «daylight use» variant enables different slat positions in the upper and lower sections. Raising The blind is raised with the slats in horizontal position or inclined slightly inwards. This allows the maximum amount of light to penetrate and ensures a gentle sliding motion for the lift tape. Development Storenmaterial AG Sales Blinds and more.