PYROS. Código: FT-PY01-I Revisión: TECHNICAL DATA. Polycarbonate tube of 4 mm. thickness LIGHT FITTING. Laquered steel painted white

Transcription

1 . TECHNICAL DATA LIGHT FITTING REFLECTOR Polycarbonate tube of 4 mm. thickness Laquered steel painted white END CAPS Aluminium 2030 (polyester paint RAL 7047) POWER SOURCE LAMP TYPE V, 50/60Hz T8 IP PROTECTION IP 66 INSULATION CLASS Class I WORK TEMPERATURE -20ºC up to +50ºC when mounting T8 lamps of 36 or 58W with optional emergency kit. -20 ºC up to +55C for oher configurations. LED tuve versions máximum temperatura depends on LED tube máximum temperature. ACCESORIES INCLUDED ATEX MARK CABLE ENTRY ATEX CERTIFICATE 2 steel zinc clamps with rubber protection and 2 eyebolts Holders. II 2GD Ex d IIB+H2 T6 Gb Ex tb IIIC T85ºC Db M25 thread (2 entries). GLAND valid for NON ARMOURED CABLE INERIS 4ATEX0064X 2. PICTURE P A G E / 0

2 3. DIMENSIONS & WEIGHT A B C TUBE / 2 TUBES WATTS (W) A B C PACKING (Units) AVAILABLE POWERS TUBE / 2 TUBES WATTS (W) ELECTRONIC DIMMABLE P A G E 2 / 0

3 5. SPECIAL ACCESSORIES 5.. CABLE GLANDS EEx d VALID FOR NON ARMOURED CABLE II 2 GD EEx d IIC T6 THREAD SIZE DIMENSIONS (mm) Ø OVERAL (mm) METRICS PG. NPT GAS CONE A B C D MÍN. MÁX. TYPE M-25 x, /4 3/ A M-25 x, /4 3/ B M-25 x, /4 3/ C M-25 x, /4 3/ D M-25 x, /4 3/ E 5.2. PLUG EEx d II 2 GD EEx d IIC T6 THREAD SIZE DIMENSIONS (mm) METRICS A B C M Important: for each light, plug and cable gland. If installed in a continuous line, 2 cable glands. P A G E 3 / 0

4 6. ATEX MARKIED NOMENCLATURE PROTECTION MODE GROUP TEMPERATURE CLASS II 2 DG Ex d IIC T6 Ex tb IIIC T85ºC Db DEVICE CATEGORY PROTECTION MODE ZONE TEMPERATURE CLASS ATEX ZONE CLASSIFICATION GROUP II FIXTURES: ABOVE GROUND INDUSTRIES ZONE CATEGORY EXPLOSIVE ENVIRONMENT PRESENCE Zone 0 Zone 20 Zone Zone 2 G (gases and vapors) D (powders) 2G (gases and vapors) 2D (powders) Constant, permanent. Occasional, frequent. Zone 2 Zone 22 3G (gases and vapors) 3D (powders) Never in normal service, only for short periods of time. GROUP I FIXTURES: MINES WITH FIRE-DAMP M M2 Presence (methane, dust) Presence risk (methane, dust) P A G E 4 / 0

5 PROTECTION MODES SYMBOL PROTECTION TYPE ZONE d Explosion proof,2 e Increased security,2 ia Intrinsic security 0,,2 ib Intrinsic security,2 o Oil inmersion 2 p Pressurized,2 q Below sand,2 m Encapsulated,2 n Antisparks 2 GROUPS II GASES CLASSIFICATION OF GASES AS YOUR TEMPERARUTA OF IGNITION ( * ) I Methane (fire-damp) A B C Acetone Acetic acid Ammonia Ethane Methylene chloride Methane (CH 4 ) Carbon oxide Propane N-Butane N-Butyl N-Hexane Acetaldehyde ethyl ether Ethyl nitrite Ethyl Ethyl oxide Sulfur Hydrogen Acetylene (C 2 H 2 ) Carbon Sulfur (CS 2 ) Hydrogene (H 2 ) TEMPERATURE CLASSES T T2 T3 T4 T5 T6 P A G E 5 / 0

6 TEMPERATURE CLASSES TEMPERATURE CLASSES MAX. SURFACE TEMPERATURE (ºC) T 450 T2 300 T3 200 T4 35 T5 00 T6 85 * The material marked as IIB suited to applications requiring material marked as IIA and IIC adapted for IIA and IIB. P A G E 6 / 0

7 8. PHOTOMETRY tube light fitting. 2 tubes light fitting. P A G E 7 / 0

8 9. APPLICATIONS The light fitting of Airfal is designed to operate in environments that can be formed or an explosive atmosphere being present according to the ATEX directives 94/9/CE and 204/34/EU. The ITC-BT-29 BOE No. 224, based on R.D. 400/996 establishes the hazardous locations where products must be installed with ATEX: Locations where volatile flammable liquid transfer from one container to another. Garages and car repair shops. It excludes garages of private use for parking of 5 vehicles or less. Interiors of paint booths where spray systems are used and their immediate environment when using solvents. Dries of material with inflammable solvents Places of extraction of fats and oils that use inflammable solvents. Places with warehouses of inflammable opened liquids or that could be opened. Zones of laundries and dry cleaner's shops in which inflammable liquids are used. Rooms of fuels. Facilities where they take place, manipulate, store or consume inflammable gases. Pump rooms and / or compressor flammable liquids and gases. Interiors of refrigerators and freezers in which inflammable matters are stored in opened containers, easily perforables or with slightly consistent closings Any other emplacement where there exists risk of explosion or of fire due to the presence of inflammable substances. * For more information contact the technical department. P A G E 8 / 0

9 0. VERSION LED TUBES 0. DIMENSIONS AND OTHER INTEREST DATA. A B C LED TUBE / 2 TUBES TUBE LED LENGHT (mm) A B C PACKING (Units) All the accesories can be use for the LED version (Cableglands, plug, ), except emergency kits. The photometry depends on the LED tube to be installed. P A G E 9 / 0

10 . VERSION WITH EMERGENCY Stand to the essential requirements of the directives : Low Voltage Directive: 2006/95/EEC. EMC Directive: 2004/08/EEC. And agrees the following harmonized documents: UNE-EN : Lamp control gear -- Part 2-7: Particular requirements for d.c. supplied electronic ballasts for emergency lighting. UNE-EN : Luminaries-specification for general requirements and test. UNE-EN : Luminaries for emergency lighting. UNE-EN 5505-: Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment EN 6547: Equipment for general lighting purposes. EMC immunity requirements UNE EN : Limits for harmonic emissions. Technical characteristics: Voltage: V / 50-60Hz - Consumption: 3W Line current: 5mA Power factor P A G E 0/ 0