BIMBO BAKERIES USA ALBANY CAKE ALBANY, NEW YORK

Size: px

Start display at page:

Download "BIMBO BAKERIES USA ALBANY CAKE ALBANY, NEW YORK"

Kory Neal
5 years ago
Views:

1 BIMBO BAKERIES USA ALBANY CAKE ALBANY, NEW YORK August, 2018 Infrared Inspection Report Bimbo Bakeries USA Albany Cake 78 North Manning Boulevard Albany, New York, Company Contact: Steve Gauck Project: CHARTER OAK DRIVE, LITTLE ROCK, AR PHONE: & FAX:

2 ORDER OF REPORT CONTENTS 1: Data To Facilitate Understanding & Utilizing Scan Report 2: Scan Results Overview & Action Taken Form 3: Identified Faulting Conditions, Information & Photographs 4: List Of Facility Equipment Identified By The Customer Representative & Notations Of Faulting Conditions Found DISCLAIMER This report and the recommendations contained in it are based upon conditions and practices observed and information made available to United Spectrographics personnel. This report does not purport to list all hazards or faulty conditions. It is not intended to indicate that other hazards or faulty conditions do not exist. Severity ratings in the report are based on the criteria shown in this report and are intended as guidelines only. No responsibility is assumed for the control of the facility s condition, maintenance practices or correction of conditions indicated herein. By issuing this report, neither United Spectrographics nor any of its employees makes any warranty, expressed or implied, concerning the contents of this report. Furthermore, neither United Spectrographics nor any of its employees shall be liable in any manner (other than liability that may be expressed in any policy of insurance that may be issued by United Spectrographics) for personal injury or property damage or loss of any kind arising from or connected with this inspection or failure to inspect.

3 Utilizing Report Contents Included in this report are Photographs and Thermographs of problem areas found during our recent Infrared Inspection of your facility. Each problem area picture is accompanied by: Date Location Information Temperature Calculations Color-coded Temperature Intensity and/or Condition Significance Data A Brief Comment Relating The Item In The Photograph To Its Corresponding Thermograph Suggested Corrective Recommendations. In most cases, problems (faults) found will be listed according to the date and order that they were located, rather then by significance or priority, as we feel that you and/or your personnel can best judge this, keeping in mind circuit importance and thermograph intensity. Thermal intensity is indicated by use of a color-coded data inserts that locate a fault s position on the standard electrical failure curve. The color of the insert represents the temperature range of the hottest item, or a portion of the item's circuitry, pointed out in the thermograph. The temperature ranges which the colored inserts represent are grouped as follows: INSERT Red Orange Yellow Green Temperature Range 70ºC/126ºF and higher above Ambient Operating Temp. 40ºC/72ºF to 69ºC/124ºF above Ambient Operating Temp. 25ºC/45ºF to 39ºC/70ºF above Ambient Operating Temp. *10ºC/18ºF to 24ºC/43ºF above Ambient Operating Temp. ( * See page 4)

Determining Cost Effective Responses Electrical equipment failures generally follow a standard mechanical/electrical failure curve. Dividing the failure curve into temp.

4 Determining Cost Effective Responses Electrical equipment failures generally follow a standard mechanical/electrical failure curve. Dividing the failure curve into temp. ranges and locating a problems position on the curve allows us to indicate the probable time to its failure. Knowing a problems probable time to failure allows you to make a cost effective response to the problem areas that we locate. Below is a depiction of the electrical fault failure curve with the thermal intensity ranges and the colors that we assign to faults detailed in our reports. STANDARD ELECTRICAL FAULT FAILURE CURVE (Does Not Include Area In Blue) MINOR INTERMEDIATE SERIOUS CRITICAL DEVICE TEMP IS AMBIENT, BUT DEVICE IS EITHER FAULTY OR UNSAFE. 10ºC * 18ºF 25ºC 45ºF 40 C 72ºF 70 C 126ºF AMBIENT TEMP YEARS MONTHS MONTHS TO WEEKS WEEKS TO NOW FAULTY EQUIP Built In Trend Monitoring When yearly scans are accomplished, report results allow you to trend monitor your electrical equipment without having to cross reference previous report findings. If a previous years problem is not repaired it will show up again in the current scan report and its current intensity range indicates a current effective response.

5 Defining Total Temperature and Ambient Operating Temperature And Explanation For Their Use Total Temperature: Total Temperature = Ambient Operating Temperature + Fault temperature Allows you, the customer, to evaluate possible damage to equipment. Leads fail between 90ºC/194ºF and 110ºC/230º Phenolic fails around 200ºC/392ºF Transformers and Motor Insulation failure temperature depends on insulation class rating. Contacts start to fail around 130ºC/266ºF Ambient Operating Temperature (AOT*) for Infrared Scanning Purposes: Temperature within a device container (Box or Cabinet) that is not directly affected by faulting component = Normal Equipment Operating Temperature Contained By Box or Cabinet. If there is no container (Example: Device mounted to a wall) it is the temperature adjacent to the device not affected by the fault. Allows you, the customer, to determine if device will operate at intended amperage. Most switchgear is rated to operate at approximately 40ºC/104ºF (Industrial) to 50ºC/122ºF (Marine) If AOT is enough above normal rated temperature, either of the following conditions can cause an unanticipated trip. 1. An intermittent high load. 2. A minor (Green) or intermediate (Yellow) fault. Report pages with photographs: PH stands for Visible Light Photograph TH stands for Infrared Light Thermograph *AOT stands for Ambient Operating Temperature Both black & white and color infrared thermographs are presented to better depict the fault condition.

6 In addition to the corrective response time frame suggested below and the failure curve located on the previous page, you may want to consider using the military standard responses presented below. Military Standard For Evaluating Faults Located In Electrical Equipment Utilizing Temperature Data Obtained With Infrared Imaging Equipment: Temperatures rise above Ambient Operating Temperature: *10ºC/18ºF to 24ºC/43ºF component failure unlikely, but corrective measures required at next scheduled routine maintenance period or as scheduling permits. (Green Label) 25ºC/45ºF to 39ºC/70ºF component failure probable, unless corrected. (Yellow Label) 40ºC/72ºF to 69ºC/124ºF component failure almost certain, unless corrected. (Orange Label) 70ºC/126ºF and above component failure imminent. Immediately inform the person responsible for continued operation of equipment. (Red Label) Note: United Spectrographics uses a Blue Label to indicate faults that require attention due to either ambient temperature (Ex: Phase Not Operating), faulty equipment elements or unsafe conditions. * Note: Temperature conditions below 10ºC/18ºF rise above AOT are not considered significant enough to record and are usually not included in the reports unless the fault temperature is being affected by a cooling medium such as oil or wind. Fault Correction Recommendation When Our Source Assessment Is Inaccurate: When a fault is indicated in a connection or component and examination by your electrician does not turn up a loose connection or faulty component where we have indicated, a fault does exist. The electrician should continue to investigate the next connection or component to be found in the direction that the heat is coming from until a source is located. Example: If a molded case breaker line side lead connection lug is indicated as a fault source and is found to be secure, but not frozen in place, look for a loose connection or sign of over temp. in the lead holder lug.

7 SCAN RESULTS OVERVIEW PROMPT ATTENTION ITEMS: Because of: 1. The intensity or heat level indicated at the time of the scan. 2. Deterioration caused by excessive temperature not present at the time of the scan. 3. Physical condition irregularities observed at the time of the scan. We recommend that the following faults be given prompt attention: Faults: #1*, #3* Items With Asterisks Have High Total or Ambient Operating Temperatures. United Spectrographics August, 2018

8 SUMMARY OF FINDINGS FAULTS BY CATEGORY NUMBER OF FAULTS FAULT NO./ITEM NO. MINOR 1 4/223 INTERMEDIATE 2 2/31 5/210 SERIOUS 1 1/31 CRITICAL 1 3/31 SERIOUS 0 0 Number of items located at facility: 337 Number of faults: 5

10 ACTION TAKEN Bimbo Bakeries USA Albany Cake Albany, New York August, 2018 Fault # Item # Category Repaired Monitor Date Name 1 31 Serious 2 31 Intermediate 3 31 Critical Minor Intermediate

PROJECT: 05140818 CUST REP: SCAN REP: Bill Trey Dent DATE: August 14th, 2018 LOCATION: Heating Oil Room

TEMP: Aø & Bø of Case Breaker Load side lead connection lug. Temp.

Note: AOT is High TH # 1 > COMMENTS Abnormal heat is being generated in case breaker connections.

11 PROJECT: CUST REP: SCAN REP: Bill Trey Dent DATE: August 14th, 2018 LOCATION: Heating Oil Room Control Cabinet Labeled: GTS Boiler Upper Right Area of Cabinet Molded Case Breaker PH # 1 > ITEM: SOURCE: TEMP: Aø & Bø of Case Breaker Load side lead connection lug. Temp. of connections and lugs range to: 109ºC / 228ºF Total Temp - 46ºC / 115ºF AOT = 63ºC / 113ºF above AOT. Note: AOT is High TH # 1 > COMMENTS Abnormal heat is being generated in case breaker connections. See orange arrows in PH#1 and TH#1. TH # 1 > Loose and/or corroded contact areas. Clean, inspect and re-secure serviceable components. TEMPERATURE ABOVE AOT 63 C / 113 F

PH # 2 ITEM: SOURCE: TEMP: Aø of Case Breaker Line side lead connection lug Temp.

Note: AOT is High < TH # 2 < TH # 2 COMMENTS Abnormal heat is being generated in case breaker component.

12 PROJECT: CUST REP: SCAN REP: Bill Trey Dent DATE: August 14th, 2018 LOCATION: Heating Oil Room Control Cabinet Labeled: GTS Boiler Upper Right Area of Cabinet Molded Case Breaker (Same as Previous) < PH # 2 ITEM: SOURCE: TEMP: Aø of Case Breaker Line side lead connection lug Temp. of connection and lug is: 75ºC / 167ºF Total Temp. - 46ºC / 115ºF AOT = 29ºC / 52ºF above AOT. Note: AOT is High < TH # 2 < TH # 2 COMMENTS Abnormal heat is being generated in case breaker component. See yellow arrows in PH#2 and TH#2. Loose and/or corroded contact area. Clean, inspect and re-secure. TEMPERATURE ABOVE AOT 29 C / 52 F

PROJECT: 05140818 CUST REP: Bill SCAN REP: Trey Dent DATE: August 14th, 2018 LOCATION: Heating Oil Room

SOURCE: TEMP: Bø of Contactor Line and load side lead connection lug. Temp.

Note: AOT is High TH # 3 > COMMENTS TH # 3 > Abnormal heat is being generated in contactor connections.

13 PROJECT: CUST REP: Bill SCAN REP: Trey Dent DATE: August 14th, 2018 LOCATION: Heating Oil Room Control Cabinet Labeled: GTS Boiler Lower Middle Area of Cabinet 2nd Contactor From Left PH # 3 > ITEM: SOURCE: TEMP: Bø of Contactor Line and load side lead connection lug. Temp. of connections and lugs range to: 119ºC / 246ºF Total Temp. - 46ºC / 115ºF AOT = 73ºC / 131ºF above AOT. Note: AOT is High TH # 3 > COMMENTS TH # 3 > Abnormal heat is being generated in contactor connections. See red arrows in PH#3 and TH#3. Loose and/or corroded contact areas. Clean, inspect and re-secure serviceable components. TEMPERATURE ABOVE AOT 73 C / 131 F

PROJECT: 05140818 CUST REP: Bill SCAN REP: Trey Dent DATE: August 14th, 2018 LOCATION: Paint Room Distribution

And Possible overload condition exists. Temp.

< TH # 4 < TH # 4 COMMENTS Abnormal heat is being generated in breaker connection.

14 PROJECT: CUST REP: Bill SCAN REP: Trey Dent DATE: August 14th, 2018 LOCATION: Paint Room Distribution Panel Labeled: PP-8 Right Side Breakers < PH # 4 ITEM: Breaker 6 SOURCE: TEMP: Load side lead connection lug. And Possible overload condition exists. Temp. of area indicating a faulting condition is: 60ºC / 140ºF Total Temp. - 40ºC / 104ºF AOT = 20ºC / 36ºF above AOT. < TH # 4 < TH # 4 COMMENTS Abnormal heat is being generated in breaker connection. See green arrows in PH#4 and TH#4. Loose and/or corroded contact area. Clean, inspect and re-secure. Check amperage to ensure it doesn t exceed 80% of manufacturer rating. TEMPERATURE ABOVE AOT 20 C / 36 F

PROJECT: 05140818 CUST REP: Bill SCAN REP: Trey Dent DATE: August 14th, 2018 LOCATION: Switchgear Room GE Switchgear Section

Bottomø of Case Breaker Possible overload conditionor internal contact area. Temp.

TH # 5 > COMMENTS Abnormal heat is being generated in breaker components. See yellow arrows in PH#5 and TH#5.

15 PROJECT: CUST REP: Bill SCAN REP: Trey Dent DATE: August 14th, 2018 LOCATION: Switchgear Room GE Switchgear Section 5 Unlabeled 480/277 Distribution Panel Molded Case Breaker Labeled: DP-2 PH # 5 > ITEM: SOURCE: TEMP: Topø, Middleø and Bottomø of Case Breaker Possible overload conditionor internal contact area. Temp. of areas indicating a faulting condition range to: 61ºC / 142ºF Total Temp. - 35ºC / 95ºF AOT = 26ºC / 47ºF above AOT. TH # 5 > COMMENTS Abnormal heat is being generated in breaker components. See yellow arrows in PH#5 and TH#5. TH # 5 > Check amperage to ensure load doesn t exceed 80% of manufacturer rating. If no overload exists or breaker begins nuisance tripping, replace breaker. TEMPERATURE ABOVE AOT 26 C / 47 F

16 AREA/EQUIPMENT LIST Following is a list of the electrical equipment located at the Bimbo Bakeries USA Albany Cake, Albany, New York, facility and data relating to its operating condition at the time the scan was performed. NOTE: Items noted as visually inspected were not operational or show no visible load at the time of the inspection. No. Equipment Operating Visually Inspected COMPRESSOR ROOM 1 DP-1 480/277 Volt Distribution Panel X Fault # 2 DP-2 480/277 Volt Distribution Panel X 3 LP-4 480/277 Volt Distribution Panel X 4 Unlabeled GE Lighting Contactor X 5 T kva GE 3ø Transformer X 6 CB-2 Molded Case Breaker X 7 Compressor Panel 480/277 Volt Distribution Panel X 8 Compressor Panel Disconnect Fuse Disconnect X 9 Compressor #1 Control Cabinet X 10 Compressor #1 Fuse Disconnect X 11 Compressor #2 Control Cabinet X 12 Doughnut Cooler Combination Starter X 13 EF-1 Drive Panel Control Cabinet X 14 EF-1 Drive Panel Fuse Disconnect X 15 EF-2 Combination Starter X 16 EF-3 Combination Starter X 17 EF-7 Combination Starter X 18 CEF #1 Combination Starter X 19 CEF #2 Combination Starter X MAINTENANCE SHOP 20 LP-1 480/277 Volt Distribution Panel X 21 LP-A 208/120 Volt Distribution Panel X 22 T-1 30 kva GE 3ø Transformer X 23 PP-1 480/277 Volt Distribution Panel X

17 No. Equipment Operating Visually Inspected 24 PP-A1 208/120 Volt Distribution Panel X Fault # 25 T-4 30 kva GE 3ø Transformer X 26 EF-5 Combination Starter X 27 EF-6 Combination Starter X OUTSIDE MAINTENANCE CAGE 28 LP-2 480/277 Volt Distribution Panel X 29 LP-B 208/120 Volt Distribution Panel X 30 T-2 45 kva GE 3ø Transformer X HEATING OIL ROOM 31 GTS Boiler Control Cabinet X 1,2,3 LITTLE BITES WAREHOUSE 32 CPP-1 240/120 Volt Distribution Panel X 33 PP-2 240/120 Volt Distribution Panel X 34 PP-3 240/120 Volt Distribution Panel X 35 PDP-2 480/277 Volt Distribution Panel X 36 Chocolate Tank Control Cabinet X 37 Chocolate Tank Agitator VFD (No Access) 38 Pan Grease Tank Control Cabinet X 39 Chocolate Receiving Pump VFD Cabinet X 40 LP-3 480/277 Volt Distribution Panel X 41 LP-C 208/120 Volt Distribution Panel X 42 T-3 Overhead GE 3ø Transformer X 43 PP-5 480/277 Volt Distribution Panel X 44 Compactor Control Cabinet X AUTO BAKE 1 45 Rack Washer Control Cabinet X 46 Rack Washer Fuse Disconnect X 47 Donut Line Motor Starter I/O Panel CP3 X 48 Pfenning Sugar System Panel Control Cabinet X

18 No. Equipment Operating Visually Inspected 49 Mixer #1 Control Cabinet X 50 Mixer #2 Control Cabinet X 51 Mixer #2 Molded Case Breaker X 52 Pan Wash AB Oven Control Cabinet X 53 (East) Wall Exhaust Fan Motor Control X 54 (Middle) Wall Exhaust Fan Motor Control X 55 (West) Wall Exhaust Fan Motor Control X BULK PACKAGING AREA 56 RP-1 480/277 Volt Distribution Panel X 57 Panel 2A Control Cabinet X 58 Panel 2 Control Cabinet X 59 Corrugated Box Former Control Cabinet X 60 Pick & Place Robot Control Cabinet X 61 Corrugated Box Closer Control Cabinet X 62 Bulk Packing Control Cabinet X 63 Robot Palletizer Control Cabinet X 64 Box Former Control Cabinet X BIG ROBOT AREA 65 Autobake 2 Small Conveyor Control Cabinet X 66 Feeds RP Amp Molded Case Breaker X 67 SDP-3 480/277 Volt Distribution Panel X 68 DP5-L 480/277 Volt Distribution Panel X 69 DP5-R 480/277 Volt Distribution Panel X 70 PP-6 208/120 Volt Distribution Panel X 71 PP-6A 208/120 Volt Distribution Panel X 72 Overhead 45 kva GE 3ø Transformer X 73 Weston Robot Control Cabinet X 74 Panel #1 Control Cabinet X 75 Panel #4 Control Cabinet X Fault #

19 No. Equipment Operating Visually Inspected 76 Cyclone #1 Control Cabinet X Fault # 77 Cyclone #2 Control Cabinet X 78 Cyclone #3 Control Cabinet X 79 Cyclone #4 Control Cabinet X 80 Cyclone #5 Control Cabinet X 81 Cyclone #6 Control Cabinet X 82 Cyclone #7 Control Cabinet X 83 Cyclone #8 Control Cabinet X 84 Cyclone #9 Control Cabinet X 85 Cyclone #10 Control Cabinet X 86 Cyclone #11 Control Cabinet X 87 Cyclone #12 Control Cabinet X 88 Cyclone #13 Control Cabinet X LITTLE BITES 2 PACKAGING /277 Volt Dist. Panel SDP2 X /277 Volt Dist. Panel DP-4-L X /277 Volt Dist. Panel DP-4-R X 92 Overhead Transformer X /120 Volt Dist. Panel PP5 X 94 Palletizer Control Cabinet X 95 Robot Case Picker Control Cabinet X 96 Robot Loader Control Cabinet (Left) X 97 Robot Loader Control Cabinet (Right) X 98 Robot #1-5 Control Cabinet X 99 Robot #6-10 Control Cabinet X 100 Conveyor AB2 Control Cabinet X 101 Case Sealer Control Cabinet X 102 Case Erector Control Cabinet X

20 No. Equipment Operating Visually Inspected 103 Autobake 2 Small Conveyors CC X 104 Hot Washer Control Cabinet X 105 Hot Washer Fuse Disconnect X 106 Bagger BG-1B Fuse Disconnect X 107 Bagger BG-2B Fuse Disconnect X 108 Bagger BG-3B Fuse Disconnect X 109 Bagger BG-1A Fuse Disconnect X 110 Bagger BG-2A Fuse Disconnect X 111 Bagger BG-3A Fuse Disconnect X 112 Bagger BG-4A Fuse Disconnect X 113 Bagger BG-4B Fuse Disconnect X LITTLE BITES 2 OVEN AREA 114 Autobake Oven 2 Control Cabinet X 115 Mixer 2 Control Cabinet X 116 Mixer 2 PLC Cabinet X 117 Mixer 2 Drive Cabinet X 118 Autobake Oven 2 Fuse Disconnect X 119 Autobake 2 Depositor 1 & 2 Control Cabinet X 120 Unlabeled Combination Starter X THERMAL ROOM 121 MC Control Cabinet X 122 Disconnect Panel B X 123 CP Control Cabinet X 124 MC Control Cabinet X 125 Disconnect Panel A X COOKIE 1 AREA 126 #87403 Little Bites Box Former Control Cabinet (No Access) 127 #87603 Little Bites Box Former Control Cabinet (No Access) 128 Cermax Palletizer Control Cabinet X Fault #

21 No. Equipment Operating Visually Inspected 129 Cermax Carton Maker Control Cabinet X Fault # 130 M1-M4 Smith Control System Conveyor Control Cabinet X st Belt Smith Control System Conveyor Control Cabinet X 132 Cookie 1 Box Closer Control Cabinet X 133 Cookie 1 Cereal Box Former Control Cabinet X 133 Cookie 1 Feeder 1 Control Cabinet X 134 Cookie 1 Feeder 2 Control Cabinet X 135 Cookie 1 Feeder 3 Control Cabinet X 136 Cookie 1 FMS Decline Control Cabinet X 137 Cookie 1 OPM 1 Control Cabinet X 138 Cookie 1 OPM 2 Control Cabinet X 139 Cookie 1 OPM 3 Control Cabinet X 140 Cookie 1 Refeed Control Cabinet X 141 Cookie 1 RR 1 Control Cabinet X 142 Cookie 1 RR 1 Sub Control Cabinet (Locked) 143 Cookie 1 RR 2 Control Cabinet X 144 Cookie 1 RR 2 Sub Control Cabinet (Locked) 145 Cookie 1 RR 3 Control Cabinet X 146 Cookie 1 RR 3 Sub Control Cabinet (Locked) 147 Cookie 1 Shaker Conveyor Control Cabinet X 148 Doughboy 1 Control Cabinet X 149 Doughboy 2 Control Cabinet X 150 Doughboy 3 Control Cabinet X 151 Full / Empty Boxes Conveyor System Control Cabinet X 152 Cookie 1 Little Bites Panel 1 240/120 Volt Distribution Panel 153 Cookie 1 Little Bites Panel 2 240/120 Volt Distribution Panel 154 (North) 30 kva Square D 3ø Transformer X 155 (West) 30 kva Square D 3ø Transformer X X X

22 No. Equipment Operating Visually Inspected kva Acme 3ø Transformer X 157 DP /277 Volt Distribution Panel X 158 DP /120 Volt Distribution Panel X 159 DP /277 Volt Distribution Panel X 160 DP /120 Volt Distribution Panel X 161 E /120 Volt Distribution Panel X 162 DP /120 Volt Distribution Panel X 163 E /120 Volt Distribution Panel X COOKIE 2 AREA 164 Cookie 2 Box Closer Control Cabinet X 165 Cookie 2 Box Former Control Cabinet X 166 Cookie 2 Conveyor Control Cabinet X 167 Cookie 2 4oz. Conveyor Line Control Cabinet X 168 Cookie 2 LB Conveyor Control Cabinet X 169 Cookie 2 Pump & Agitator Control Cabinet X 170 Cookie 2 Tray Filler Control Cabinet X 171 Chocolate Melt & Delivery Panel Control Cabinet X 172 Donut Box Former Control Cabinet X 173 Triangle Box Filler Control Cabinet X 174 Shrink Wrap Conveyor Control Cabinet X 175 Unlabeled Allen-Bradley Combination Starter X 176 LPE 230 Volt Distribution Panel X OUTSIDE COOKIE 2 AREA 177 LP-5 480/277 Volt Distribution Panel X 178 DP /277 Volt Distribution Panel X 179 PP /120 Volt Distribution Panel X COOKIE MAKE-UP AREA 180 Cookie 1 Mixer Control Cabinet X 181 Cookie 2 Mixer Control Cabinet X Fault #

23 No. Equipment Operating Visually Inspected 182 Cookie 1 Oven Control Cabinet X Fault # 183 Cookie 2 Oven Control Cabinet X 184 Panel CBE Control Cabinet X 185 Panel CBEB Control Cabinet X 186 Extruder Roll Drive VFD X 187 Band Drive VFD X 188 Wire Cut Drive VFD X 189 Oscillating Knife VFD X 190 Rack 6 PLC Cabinet X 191 DB-6 480/277 Volt Distribution Panel X COOKIE WAREHOUSE 192 DB-3L 480/277 Volt Distribution Panel X 193 DB-3R 480/277 Volt Distribution Panel X 194 PP-4 208/120 Volt Distribution Panel X 195 XFMR-4 Overhead 15 kva GE 3ø Transformer X COOKIE OVEN AREA 196 Cookie 1 Conveyor Panel X 197 Cookie Incline Conveyor PLC Cabinet X 198 Cookie 1 Guillotine VFD X 199 Oven Conveyor Control Cabinet X 200 DP /277 Volt Distribution Panel X 201 DP-20 Molded Case Breaker X 202 CI Exhaust Motor Control X 203 Lanly Fan Motor Control X 204 AHU Motor Control X 205 Cookie 1 Water Motor Control X SWITCHGEAR ROOM 206 GE Switchgear Section 1 Incoming Lines X

24 No. Equipment Operating Visually Inspected 207 GE Switchgear Section 2 Main Circuit Breaker X Fault # 208 GE Switchgear Section 3 480/277 Volt Distribution Panel X 209 GE Switchgear Section 4 480/277 Volt Distribution Panel X 210 GE Switchgear Section 5 480/277 Volt Distribution Panel X E-25 Fuse Disconnect X SIFTER AREA 212 Portable Tank Panel 208/120 Volt Distribution Panel X 213 CO 2 Alarm Relay Panel X 214 Sift Tower Control Cabinet X 215 DP-X Blower Room Control Cabinet X HIGH FRUCTOSE CORN SYRUP ROOM 216 Fructose Tank Pump Combination Starter X CORN SYRUP ROOM 217 Corn Syrup Tank Heater Control Cabinet X PH WATER BUFFER ROOM 218 Chemical Pump Control Cabinet X 219 Mixer Control Cabinet X SCALING ROOM 220 Scaling Room Blender Control Cabinet X 221 Rack 1 & Rack 2 PLC Cabinet X PAINT ROOM 222 PP-8A 208/120 Volt Distribution Panel X 223 PP-8 208/120 Volt Distribution Panel X DP-12-L 480/277 Volt Distribution Panel X 225 DP-12-R 480/277 Volt Distribution Panel X 226 DP /277 Volt Distribution Panel X 227 XFMR-8 45 kva Square D 3ø Transformer X 228 Scaling Room Exhaust Control Cabinet X

25 No. Equipment Operating Visually Inspected 229 Roof Exhaust Cookie Oven Exit (No Access) Fault # 230 Spare Blower Motor Control X BOILER ROOM 231 PP-1 208/120 Volt Distribution Panel X 232 DP-1-L 480/277 Volt Distribution Panel X 233 DP-1-R 480/277 Volt Distribution Panel X 234 XFMR-1 Overhead GE 3ø Transformer X 235 Chiller Panel Disconnect Molded Case Breaker X 236 Chiller Panel 480/277 Volt Distribution Panel X 237 P-1A Combination Starter X 238 P-1B Combination Starter X 239 Compressor 1 Control Cabinet X 240 Compressor 2 Control Cabinet X 241 Boiler 1 Control Cabinet X 242 Boiler 1 Burner Control Cabinet X 243 Boiler 2 Control Cabinet X 244 Boiler 2 Burner Control Cabinet X 245 (Left) Boiler Water Feed Pump Motor Control X 246 (Right) Boiler Water Feed Pump Motor Control X 247 Boiler Feed System Control Cabinet X 248 Wall Fans #1 & #2 Control Cabinet X BIN WASH AREA 249 CIP Control Cabinet X SOYBEAN TANK 250 Soybean Pump Control Cabinet X 251 Soybean Pump Fuse Disconnect X 252 Central Vacuum System Combination Starter X

26 No. Equipment Operating Visually Inspected BACKWASH PIT 253 PP-3 208/120 Volt Distribution Panel X Fault # 254 DP-2-L 480/277 Volt Distribution Panel X 255 DP-2-R 480/277 Volt Distribution Panel X 256 SDP-1 480/277 Volt Distribution Panel X 257 XFMR-3 30 kva GE 3ø Transformer X 258 Oven Exst. #2 Combination Starter X 259 Oven Exst. #1 Combination Starter X 260 Sigma Thermal Room Combination Starter X 261 Warehouse Intake Fan Combination Starter X /277 Volt Dist. Panel DP2-RA X CONDITIONED STORAGE ROOM 263 Egg-A Distribution Control Cabinet X OUTSIDE BREAKROOM 264 DP-7 480/277 Volt Distribution Panel X 265 PP-7 208/120 Volt Distribution Panel X 266 Overhead 15 kva GE 3ø Transformer X OUTSIDE 267 Pad Mounted Transformer (Cooling Fins Only) X 268 Riser Pole w/ (3) Pod Transformer Bank & (3) Fuse Disconnects GRAVEL ROOF 269 Unlabeled 480/277 Volt Distribution Panel X 270 Exhaust Fan Disconnect X 271 Unlabeled Exhaust Fan Disconnect (Above New Little Bites Line) 272 Unlabeled Combustion Blower Disconnect X 273 York Chiller Control Cabinet X 274 RTU-1 Control Cabinet X 275 RTU-1 Fuse Disconnect X X X

27 No. Equipment Operating Visually Inspected 276 RTU-2 Control Cabinet X Fault # 277 RTU-2 Fuse Disconnect X 278 Office A/C Unit Disconnect X 279 Bryant RTU Control Cabinet (Left) X 280 Bryant RTU Disconnect (Left) X 281 Bryant RTU Control Cabinet (Right) X 282 Bryant RTU Disconnect (Right) X Ton RTU Control Cabinet X Ton RTU Disconnect X Miami Cookies Cooling Tunnel #1 Control Cabinet X Miami Cookies Cooling Tunnel #1 Fuse Disconnect X Miami Cookies Cooling Tunnel #2 Control Cabinet X Miami Cookies Cooling Tunnel #2 Fuse Disconnect X Triangle C-2 Carrier Unit Control Cabinet X Triangle C-2 Carrier Unit Disconnect X Krack Chiller Control Cabinet X Krack Chiller Disconnect X #1 Condenser Control Cabinet X #2 Condenser Control Cabinet X Chiller Control Cabinet X Chiller Disconnect X Krack Chiller Control Cabinet X Krack Chiller Disconnect X Carrier A/C Unit Control Cabinet X Carrier A/C Unit Disconnect X RTU Control Cabinet X RTU Disconnect X Reznor Control Cabinet X

28 No. Equipment Operating Visually Inspected Reznor Disconnect X Fault # Reznor Control Cabinet X Reznor Disconnect X Exhaust Fan Disconnect X Carrier Unit Control Cabinet X Carrier Unit Fuse Disconnect X York A/C Unit Control Cabinet X York A/C Unit Fuse Disconnect X Exhaust Fan Disconnect X Modine WeatherPack Control Cabinet X EAST ROOF 314 Wessels Control Cabinet X 315 Wessels Disconnect X Reznor Control Cabinet (No Access) Reznor Disconnect X Reznor Control Cabinet (No Access) Reznor Disconnect X Reznor Control Cabinet (No Access) Reznor Disconnect X Reznor Control Cabinet X Reznor Disconnect X Reznor Control Cabinet X Reznor Disconnect X Reznor Control Cabinet (No Access) Reznor Disconnect X Reznor Control Cabinet X Reznor Disconnect X Reznor Control Cabinet X

29 No. Equipment Operating Visually Inspected Reznor Disconnect X Fault # Reznor Control Cabinet (No Access) Reznor Disconnect X Reznor Control Cabinet X Reznor Disconnect X Chandler Control Cabinet X Chandler Disconnect X

ARAMARK CLEANROOM SERVICES LOS ANGELES, CALIFORNIA

ARAMARK CLEANROOM SERVICES LOS ANGELES, CALIFORNIA March, 2013 Infrared Inspection Report Aramark Cleanroom Services MC#513 Company Contact Emmanuel Rojas Project: 07060313 2605 CHARTER OAK DRIVE, LITTLE