SAFETY Choose more than sensor...

Transcription

1 SAFETY Choose more than sensor... SECTION

2 2 Stainless steel wall-hung closet BSNZ 01 is a stainless steel wall-hung closet in matt finish and anti-vandal form. It is made of stainless steel of 2 mm thickness, sitting and bearing parts are of 3 mm thickness. The edges of the sitting part are rounded to foreclose any injury of the user. The whole closet was designed in a way to minimize the possibility of self-injury wilful brakes of arms, fingers, etc. The closet does not include any parts, that could be demounted (e.g. the sitting board). Longer version for handicapped people (BSNZ 01 INV) is offered as well. BSNZ 01 (INV) with its anti-vandal design is intended mainly for prisons, diagnostic establishments, psychiatric medical institutions and other institutions where higher resistance against wilful damage is important. BSNZ 01 Water inlet: d = 34 mm Minimum water flow capacity: 70 l / min Outlet: d = 90 mm Required spacing between bolts: 180 mm Weight: 18 kg (BSNZ 01) 23 kg (BSNZ 01 INV) stainless steel closet screws for fixing 1. Set-up water inlet as per picture 2. Set-up outlet d = 90 mm as per picture 3. Set-up the cantilever or other system for hanging the closet Example of an order 1 pc. BSNZ 01 stainless steel wall-hung closet in anti-vandal version, 2 mm thick, designed to prevent any self-injury 1 pc. BSNZ 01 INV stainless steel wall-hung closet in anti-vandal version, 2 mm thick, extended length for handicapped people, designed to prevent any self-injury BSNZ 01 BSNZ 01 INV side view side view A water inlet D - outlet CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

3 3 Stainless steel free-standing closet BSNZ 02 is a stainless steel free-standing closet in matt finish and anti-vandal version. Water outlet is standardly led down (on request possible to the left/right side or back side of the closet). It is made of stainless steel of 2 mm thickness, sitting and bearing parts are of 3 mm thickness. The edges of the sitting part are rounded to foreclose any injury of the user. The whole closet was designed in a way to minimize the possibility of self-injury wilful brakes of arms, fingers, etc. The closet does not include any parts, that could be demounted (e.g. the sitting board). Longer version for handiccaped people (BSNZ 02 INV) is offered as well. BSNZ 02 (INV) with its anti-vandal design is intended mainly for prisons, diagnostic establishments, psychiatric medical institutions and other institutions where higher resistance against wilful damage is important. BSNZ 02 should be used as more hygienic version of squat closet or in places, where it is not possible to use a wallhung closet e.g. thin plaster wall. BSNZ 02 Water inlet: d = 34 mm Minimum water flow capacity: 70 l / min Outlet: d = 90 mm Weight: 22 kg (BSNZ 02) 27 kg (BSNZ 02 INV) stainless steel closet screws for fixing 1. Set-up water inlet as per picture 2. Set-up outlet d = 90 mm as per picture Example of an order 1 pc. BSNZ 02 stainless steel free-standing closet in anti-vandal version, 2 mm thick, designed to prevent any self-injury BSNZ 02 1 pc. BSNZ 02 INV stainless steel free-standing closet in anti-vandal version, 2 mm thick, extended length for handicapped people, designed to prevent any self-injury BSNZ 02 INV side view side view A water inlet D - outlet CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

4 4 Flushing system of closets BSAZ 01 is an anti-vandal flushing system for installation into the wall. With its sturdy construction the flushing system is intended for force flushing of closets in the areas with higher danger of wilful damage (public restrooms, prisons, etc.). The flushing system is built-in the wall (in the installation box) and from front side is covered by a robust stainless steel plate (3 mm thick), including also anti-vandal push-button. The front panel is screwed by means of safety screws (can be screwed out only with special tools) to the installation box in the wall. Function of the flushing system: After pushing the button, the electromagnetic valve is opened water under pressure starts flowing for the period, which is preset by owner. For another flush, it is necessary to push the button again. Should the push-button be wilfully arrested in pushed-down position, the water will not flow after the first flush. The system is also equipped with forced pause which means that after second flush the system will not react for some preset time. Therefore, constant wilful flushing and needless water spending is prevented. BSAZ 01 Dimensions of front panel: Power supply: Power requirement: Water pressure: Adjustable time of water flow: Adjustable time of delay: 250x180 mm max. 6 VA 1-10 bar 1 s 250 s in 1 s intervals 10 s 42,5 min in 10 s intervals mounting case with electromagnetic valve, electronics and screwing covering plate with anti-vandal push-button 1. Set-up alcove for installation (230x160x120 mm) 2. Set-up cable for power-supply (12V, 50Hz from power-supply unit ZAC) 3. Set-up water inlet A water inlet G 1/2 (inner winding) C power supply CYKY 2 x 1,5 G water outlet into the closet G 1 (3/4 ) BSAZ 01 anti-vandal flushing system of closets, 3 mm thickness, 12 V/ 50 Hz KZ 1 A water inlet D - outlet KZ 1 cantilever is intended for hanging the closet on carrying bolts. With its construction the cantilever ensures a steady load between the floor and the walling. This allows the wall-hung closets to be fixed onto the walls with a lower load capacity. Cantilevers are not suitable for mounting onto a plaster slabs. KZ 1 can be completed with an holder for BSAZ 01. Construction KZ 01 allows hanging closets with spacing of assembly screws 180 and 230 mm setting of the sitting height from 390 to 490 mm (suitable for handicapped modification) outlet pipe diameter d = mm setting of the span between water inlet and outlet pipes from 135 to 175 mm KZ 1 cantilever for wall-hung closets closets SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

5 5 Anti-vandal shower control BSAS 01 is an anti-vandal shower control system for installation into the wall. With its sturdy construction the system is intended for controlled water consumption in the areas with higher danger of wilful damage (public showers, prisons, etc.). The mechanism of BSAS 01 is built in the wall (in the installation box) and from front side is covered by a robust stainless steel plate (3 mm thick), including also anti-vandal push-button. The front panel is screwed by means of safety screws (can be screwed out only with special tools) to the installation box in the wall. Function of the flushing system: After pressing the button the user will get the preset amount of water. The water flow stops automatically after the preset amount is used up. Should the push button be wilfully arrested in pushed-down position, the water will not flow after the first cycle. The water amount is preset by the owner, not by the user. BSAS 01 Dimensions of front panel: 202x182 mm Power supply: Power requirement: max. 6 VA Water pressure: 1 10 bar Adjustable time of water flow: 10 s 42,5 in 10 s intervals installation box with electromagnetic valve, electronics and screwing covering plate with anti-vandal push-button 1. Set-up alcove for installation (180x160x80 mm) 2. Set-up power-supply cable (12V, from powersupply unit ZAC) 3. Set-up water inlet 1 pc. BSAS 01.1 shower control for premixed water, anti-vandal version, thickness of 3 mm, 12V/50Hz 1 pc. SP 2 anti-vandal shower arm, 7l/min A water inlet G 1/2 (inner winding) C power supply CYKY 2 x 1,5 G water outlet into shower arm G 1/2 (inner winding) CLOSETS Showers URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

6 6 Token-operated shower control BSZA 01 is an automatic token-operated shower control set for installation into the wall. With its sturdy construction it is intended for paid water take-off in the areas with higher danger of wilful damage (public showers, prisons, etc.). Front side of the automat is made of 3 mm thick stainless steel plate including anti-vandal stainless steel cover of thermostat. Assemblage and anchorage is realized through the wall. Tokens in the automat are accessible from the back side. All water connecting parts are included in delivery. The shower arm (e.g. anti-vandal SP 2) is necessary to order extra. Function of the shower unit: After inserting a token, water starts to flow. The user operates the shower by pressing a START/STOP piezo button. The user is given notice by the interrupted water flow that the showering time is getting to its end (1 min. before the end). BSZA 01 Dimensions of front panel: 250x500 mm Installation wall thickness: min 100 mm Power supply: Token: ZT 1 Power requirement: max. 6 VA Water pressure: 1 10 bar Adjustable time of water flow: 10 s 42,5 min in 10 s intervals Total time of operation: 2x adjusted time of water flow 1. Set-up alcove for installation 2. Set-up power-supply cable (12V, 50Hz from power-supply unit ZAC) 3. Set-up water inlet Versions types BSZA 01.1 token-operated shower control for one pemixed water BSZA 01.TV token-operated shower control for hot and cold water with thermostatic valve 1 pc BSZA 01.1 token-operated shower control for one pemixed water, 3 mm thick cover plate, 12 V/50 Hz, installation through the wall 1 pc BSZA 01.TV token-operated shower control for hot and cold water with thermostatic valve, 3 mm thick cover plate, 12 V/50 Hz, installation through the wall A hot water inlet B cold water inlet C power supply D water outlet into the shower CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

7 7 Token-operated wall-hung shower unit BSZA 02 is a token operated shower automat indended for assembly onto the wall. Shower panel is made of 2 mm thick stainless steel and does not include any demountable components. No mechanic lock, which could be damaged or opened, is contained either. Storage tank for tokens is opened electronically by means of electromagnetic lock. If the lock is locked, it is not possible to demount the shower panel from the carrying frame. Function of the shower unit: After inserting a token, water starts to flow. The user operates the shower by pressing a START/STOP piezo button. The user is given notice by the interrupted water flow that the showering time is getting to its end (1 min. before the end). Dimensions: 220x1000x70 mm BSZA 02 Power supply: Token: ZT 1 Power requirement: max. 6 VA Water pressure: 1 10 bar Water inlet: G ½ Adjustable time of water flow: 10 s 42,5 Total time of operation: in 10 s intervals 2x adjusted time of water flow 1. Set-up cable for power supply from power-supply unit ZAC) 2. Set-up water inlet Versions types BSZA 02.1 for one premixed water BSZA 01.TV for hot and cold water with thermostatic valve 1 pc. BSZA 02.1 anti-vandal token operated shower for one premixed water, 2 mm thick panel, installation on the wall, 12V/50 Hz 1 pc. BSZA 02.TV anti-vandal token operated shower with thermostatic valve, 2 mm thick panel, installation on the wall, 12/50 Hz A hot water inlet B cold water inlet C power supply K storage tank for tokens CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

8 8 Stainless steel urinal BSTP 01 is an integral stainless steel urinal with a built-in capacitive sensor. This sensor generates a signal that is analyzed by the electronics, opens the electromagnetic valve and operates the flushing of the urinal. After 6 hours inactivity the urinal flushes itself. The flushing system is protected against mechanical damage, even wilful, because all components are placed under the cover of the urinal. Battery supplied version of BSTP 01 can be manufactured on a request. Automatic stainless steel urinal BSTP 01, due to its high resistance to damage, is intended particularly for modernization of the prisons, diagnostic establishments and other institutions where security is paramount. BSTP 01 Water inlet: G 1/2 Water pressure: 1 10 bar Outlet: d = 50 mm Time of flushing: 5s Power supply: Power requirement: 6 VA Power-supply unit: ZAC 1/20 (max 3 x BSTP 01) ZAC 1/50 (max 8 x BSTP 01) Material thickness: 2 mm Weight: 10 kg stainless steel urinal siphon with electronics electromagnetic valve with connecting hose assembling material COS 1 Time flushing system for urinals and troughs COS 1 is a time-controlled flushing system for one urinal, group of urinals or urinal trough. It is possible to set up periodical flushing during a day, interval between individual flushing or duration of flushing. COS 01 can also use an external source as an initiatory signal, for example school bell during breaks. Flushing system can be installed outside the toilet, where is more protected against unauthorized handling or wilful damage. Input voltage: 250 V, 50 Hz Output voltage: Power requirement: max 50 VA (depends on number of valves) Dimensions: 280x225x100 mm A water inlet G 1/2 C electric input CYKY 2A x 1,5 D outlet E capacitive sensor NP 01 Stainless steel partition wall NP 01 is intended for separation of individual urinals. Dimensions 800x495 mm. Delivery includes fixing material. 1.Set-up water inlet, pipe 1/2 as per picture 2.Set-up outlet d = 50 mm 3.Set-up cable for power supply from source of power supply ZAC 1 pc. BSTP 01 safety stainless steel urinal with an automatic capacitive flushing system, CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

9 9 Stainless steel urinal troughs BSPZ 01 is a stainless steel wall-hung urinal trough in anti-vandal version. BSPZ 02 is a stainless steel wall-to-floor urinal trough in anti-vandal verison. Urinal troughs are made of 2 mm thick stainless steel AISI 304 and have sandblasted matt finish. To order, it is possible to use 3 mm thick stainless steel. BSPZ troughs are equipped with stainless steel flushing nozzles. Delivery includes complete water connection material. Connection is possible from both sides (pipe plug included). BSPZ trough is delivered in four standard lengths, any other required length possible to order. The version type of the trough can be right or left according to the placing of the outlet (from front view). COS 1 time flushing system is recommended as suitable automatic flushing system. BSPZ 01 BSPZ 02 Water inlet: G 1/2, inner winding Outlet: d = 40 mm (BSPZ 01) d = 50 mm (BSPZ 02) Weight: kg (depends to the type) stainless steel urinal trough including water connection material and nozzles siphon d=40 or 50 mm anchoring material 1. Set-up water inlet G 1/2, inner winding 2. Set-up outlet as per the scheme Version types BSPZ wall-hung urinal trough, 1250 mm BSPZ wall-hung urinal trough, 1900 mm BSPZ 01.3 wall-hung urinal trough, 2500 mm BSPZ wall-hung urinal trough, 3000 mm BSPZ 01 BSPZ 02 BSPZ 02.1 wall-to-floor urinal trough, 1250 mm BSPZ 02.2 wall-to-floor urinal trough, 1900 mm BSPZ 02.3 wall-to-floor urinal trough, 2500 mm BSPZ 02.4 wall-to-floor urinal trough, 3000 mm A water inlet G1/2, (Inner Winding) D - outlet CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

10 10 Automatic anti-vandal washbasin BSAU 01 is a sensor controlled anti-vandal washbasin. Because of its sturdy design, it is intended mainly for installation into the walls of the penitentiary facilities and everywhere where high security standards of hygienic equipment are needed. After inserting hands into the inner area of the washbasin, the infrared beam is disconnected and the electronics turns the water on. Water runs for preconfigured period of max. 30 sec., which prevents constant water flowing if the sensor is wilfully screened for longer period. The washbasin can be built into the wall of mm thickness. Version for thinner wall made to order. BSAU 01 Water inlet: G ½ Outlet: d = 40 mm Dimensions of front cover: 420 x 400 mm Electricity protection: IP 55 Preset time of water flow: 40 sec. Water pressure: 1-10 bar Power supply: Power requirement: 6 VА Power-supply unit: ZAC 1/20 (max. 3 x BSAU 01) ZAC 1/50 (max. 8 x BSAU 01) Weight: 10 kg sink with sensor and front cover back cover bolts M8 x 240 mm with nuts (4 pcs.) corner valve with filter outlet siphon connecting hose nozzle 1. Set-up alcove through the wall 350 x 350 mm for installation of the washbasin 2. Set-up water inlet (as per picture) 3. Set-up outlet 4. Set-up cable for power supply Version types BSAU 01.1 automatic washbasin for one premixed water BSAU 01.2 automatic washbasin for hot and cold water with mixing valve BSAU 01.TV automatic washbasin with thermostatic valve sensor beam 1 pc. BSAU 01.1 automatic safety washbasin for assembly into the wall, mixed water, CLOSETS SHOWERS Sprchy URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

11 11 Anti-vandal stainless steel washbasin BSAU 02 is a vandal-proof washbasin intended mainly for installation into the penitentiary facilities and everywhere where high security standards of hygienic equipment are needed (e.g. highway lay-byes). Main advantages of BSAU 02: all the components are located under the stainless steel casing (including siphon and water inlet) water outlet is made from thick stainless steel pipe which is not possible to bend or break off by standard instruments water dosing is controlled by electronics. By pushing down the vandal-proof button, the electronics dose only the preset amount of water the vandal-proof push-button only gives pulses for water dosing, therefore water stops running after the preset amount was released even in case that the button is blocked in pushed-down position BSAU 02 was designed in the way that people in penitentiary facilities cannot wilfully hurt themselves The vandal-proof washbasin is manufactured from the stainless steel sheet of 2 mm thickness and is resistant to wilful damage. The washbasin has sandblasted finish. The electronics is supplied with 12V, 50 Hz from the source of power supply ZAC 1/20. The standard version of BSAU 02 includes connection to one premixed water. Different dimensions or additional accessories are possible to order. BSAU 02 Water inlet: G ½ Outlet: d = 40 mm Dimensions: 600 x 435 x 460 mm Diameter of sink: d=370 mm Electricity protection: IP 55 Preset time of water flow: 1s 250 s in 1 s intervals Water pressure: 1-10 bar Power supply: Power requirement: max. 6 VА Power-supply unit: ZAC 1/20 (max. 3 x BSAU 02) ZAC 1/50 (max. 8 x BSAU 02) 1. Set-up water inlet, pipe ½ as per picture 2. Set-up outlet d = 40 mm or d = 50 mm 3. Set-up cable for power supply 12V, 50Hz from power supply unit ZAC 1 pc. BSAU 02 stainless steel washbasin including anti-vandal control, 2 mm thick, version against self-injury, 12 V/ 50Hz A water inlet G1/2, inner winding C Electricity input CYKY 2A x 1,5 D outlet CLOSETS SHOWERS Sprchy URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

12 12 Anti-vandal tap for washbasins BSAU 03 is a vandal-proof tap for washbasins intended for installation into the wall. The user can adjust water temperature by means of thermostatic valve equipped with anti-vandal stainless steel cover. The outflow arm is made of 2 mm thick stainless steel which ensures high vandal resistivity. Cover plate of the tap is made of 3 mm thick stainless steel and is screwed by means of safety bolts to the installation box in the wall. Water flow is operated with the push-button on the cover. After pressing the push-button the user gets the prconfigurated amount of water. Should the push-button be wilfully fixed in the push-down position, water stops flowing after the preset amount of water is used. Water amount can be preset only by the owner (not the user). BSAU 03 Dimensions of front panel: 330 x 230 mm Length of the outflow arm: 200 mm Power supply: Power requirement: max. 6 VA Water pressure: 1 10 bar Adjustable time of water flow: 10 s 42,5 min in 10 s intervals installation box with electromagnetic valve, screwing and electronics covering plate with outflow arm, TV and stainless steel push-button 1. Set-up water inlet as per picture 2. Set-up cable for power supply 12V, 50Hz from power supply unit ZAC 3. Set-up alcove for installation 300 x 200 x 80 mm Version types BSAU 03.1 anti-vandal tap for one premixed water BSAU 03.2 anti-vandal tap for hot and cold water with mixing valve BSAU 03.TV anti-vandal tap with thermostatic valve 1 pc. BSAU 03.TV stainless steel washbasin tap with thermostatic valve, 3 mm thick, 12V 50 Hz A cold (or premixed) water inlet G 1/2 - inner winding B - hot water inlet G 1/2 - inner winding C power supply 12 V from power supply unit ZAC (CYKY 2 x 1,5) * other possibilities of inlets CLOSETS SHOWERS Sprchy URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

13 Safety combi set with closet, washbasin and fountain BSK 01 combines closet, washbasin and fountain in one compact set. It is designed particularly for modernization of the prisons, dagnostic establishments and other institutions where security is paramount. Operation of toilet, washbasin and drinking fountain is independent and it is possible to use all three appliances at the same time. All three appliances are easily operated by separate safety press buttons that are connected to the electronics. The elecronics ensures that the water flows only for the preconfigured period of time and not longer, even when the button is pressed. Each appliance can be set up for individual distribution of water which brings remarkable water savings. Entire set is manufactured from a high quality stainless steel of 2 mm thickness. Anti-vandal design and stainless steel durability warrants long service life even in the toughest environments. Sandblasted finish ensures easy cleaning and maintenance of the set. There are two easy methods of mounting the set to the wall. The first method is anchoring the set from its sides to the wall by safety screws. The second method is anchoring the set through the wall. All the water outlets and inlets are hidden inside of the set and are non-accessible to the user. Electronics is supplied with a.c. voltage of 12V, 50Hz from the power-supply unit ZAC 1/50. Safety set BSK 01 can be adapted in sizes and combinations of the appliances according to the individual needs of the customer. BSK 01 is produced in two standard versions left and right (depends on the location of the closet). BSK 01 Water inlet: G 1 Outlet: 110 mm Power supply: Power requirement: max 20 VA Dimensions: 1000 x 1120 x 550 mm Weight: 70 kg 13 combi set casing with fixing frame outlet valve 3 pcs. (1/2, 3/4 ) connecting hose 2 pcs. spherical valve 2 pcs. electronics control push-button 3 pcs. fixing material 1. Set-up water inlet as per picture on pg Set-up outlet 110 mm as per picture on pg Set-up power supply cable 12V, 50Hz (from power supply unit ZAC not part of delivery) T1 water inlet T2 flushing system T3 fountain control 1 pc. BSK 01 safety combination set (washbasin, closet, fountain), right version, anti-vandal pushbuttons, adjustable time of water flow, 12V, 50Hz CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

14 14 Safety combi set with closet and washbasin (version types) BSK 02 combi set can be produced in various dispositional versions and without the fountain only closet and washbasin. Version types: closet located on front side or on left/right side. All connections and functions are same as with BSK 01. Other versions according to the individual needs of the customer are possible. BSK 02 is produced in two standard versions - left and right (depending on the location of the closet). BSK 02 BSK with closet on front side left version BSK with closet on the side right version T1 - washbasin water flow system T2 flushing system of closet T3 water aerator 1 pc. BSK 02 - safety combi set washbasin + closet, front-side left version, push-button control system, adjustable time of water flow, 12V, 50Hz 1 pc. BSK 02 safety combi set washbasin + closet, right-side version, push-button control system, adjustable time of water flow, 12V, 50Hz CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS safety SETS

15 15 Minimum recommended installation space and requirements for setting up the construction BSK 01 Right version A water inlet 1 B premixed water inlet ½ C electricity supply D outlet BSK 02 Front-side left version A water inlet 1 B premixed water inlet ½ C electricity supply D outlet BSK 02 Right-side version A water inlet 1 B premixed water inlet ½ C electricity supply D outlet CLOSETS SHOWERS URINALS, TROUGHS WASHBASINS, TAPS SAFETY SETS

16 Aqua program automatic flushing systems of urinals and water closets automatic taps for washbasins sensor-controlled showers stainless steel program for public restrooms accessories Stainless steel program sensor-controlled washbasins sensor-controlled wash-troughs sanitation containers bucket sinks dryers of boots and coats automatic washers for boots and aprons Coin and token-operated automats shower units shower columns shower controls door automats automats for electrical appliances Safety section safety water closets safety urinals safety washbasins safety wash-troughs safety coin-operated automats safety combi sets Company AZP Brno is a holder of an ISO 9001:2000 quality certificate since the year of All the products of AZP Brno are tested and certified in Technical Testing Institution Piešťany and conform to the appropriate European Union standards. AZP Brno s.r.o. Sladovnická 17, Brno, Czech Republic tel.: fax: azp@azp.cz sales representative: