PS PS PSA 2 500

Transcription

1 en Pump PS PS PSA OPERATOR S MANUAL E N

2

3 Foreword Foreword This manual provides information and procedures to safely operate and maintain this Wacker Neuson model. For your own safety and protection from injury, carefully read, understand and observe the safety instructions described in this manual. Keep this manual or a copy of it with the machine. If you lose this manual or need an additional copy, please contact Wacker Neuson Corporation. This machine is built with user safety in mind; however, it can present hazards if improperly operated and serviced. Follow operating instructions carefully! If you have questions about operating or servicing this equipment, please contact Wacker Neuson Corporation. The information contained in this manual was based on machines in production at the time of publication. Wacker Neuson Corporation reserves the right to change any portion of this information without notice. All rights, especially copying and distribution rights, are reserved. Copyright 2008 by Wacker Neuson Corporation. No part of this publication may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission from Wacker Neuson Corporation. Any type of reproduction or distribution not authorized by Wacker Neuson Corporation represents an infringement of valid copyrights and will be prosecuted. We expressly reserve the right to make technical modifications, even without due notice, which aim at improving our machines or their safety standards. wc_tx000001gb electric.fm 3

4 Foreword wc_tx000001gb electric.fm 4

5 PS / PS / PSA Table of Contents Foreword 3 1. Safety Information Operating and Electrical Safety Information Labels Operation Names of Parts Prior to Operation Installation Electrical Wiring Electrical Circuit Diagrams Operation Maintenance Periodic Maintenance Table Maintenance and Inspection Disassembly/Reassembly Disassembly Reassembly Troubleshooting Technical Data Standard Specifications Operating Specifications (60 Hz) Dimensions wc_bo en_003toc.fm 5

6 Safety Information PS / PS / PSA Safety Information This manual contains DANGER, WARNING, CAUTION, NOTICE and NOTE callouts which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury. CAUTION CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. NOTICE: Used without the safety alert symbol, NOTICE indicates a situation which, if not avoided, could result in property damage. Note: Contains additional information important to a procedure. wc_si000035gb.fm 6

7 PS / PS / PSA Operating and Electrical Safety Safety Information WARNING To reduce risk of electric shock, connect only to a properly grounded, grounding-type receptacle. Risk of electric shock this pump has not been investigated for use in swimming pool areas. An acceptable motor-control switch shall be provided at the time of installation according to local codes and regulations. To reduce risk of electric shock, follow instructions in this manual for proper installation. CAUTION: This pump may automatically restart. Prior to working on the pump or control panel, all supply circuits must be disconnected. CAUTION: Risk of shock do not remove cord and strain relief. 1.2 Information Labels Label Wacker Neuson Corporation Menomonee Falls, WI USA Model Item No. Rev. Serial No. Man.Y/M THERMALLY PROTECTED INDOORS OR OUTDOORS CSA ENCLOSURE 3 V Hz Phase Amp. Conforms to UL Std. 778 Cert. to CAN/CSA Std. C22.2 No. 108-M89 Max. m Max. L/min kg kw Max. ft Max. GPM lbs HP C US L I STED MADE IN TAIWAN R Meaning A nameplate listing the model number, item number, revision number, and serial number is attached to each unit. Please record the information found on this plate so it will be available should the nameplate become lost or damaged. When ordering parts or requesting service information, you will always be asked to specify the model number, item number, revision number, and serial number of the unit. wc_si000035gb.fm 7

8 Operation PS / PS / PSA Operation 2.1 Names of Parts See Graphic: wc_gr wc_gr Ref. Description Ref. Description 1. Lifting Handle 8. Seal-mechanical 2. Coupling 9. Lubricant 3. Oil Lifter 10. Seal-dust 4. Oil Plug 11. Sleeve 5. Cover-suction 12. Housing-oil 6. Strainer 13. Wear Ring 7. Cable Assembly 14. Impeller wc_tx000113gb.fm 8

9 PS / PS / PSA Prior to Operation Operation CAUTION 2.3 Installation When the pump is delivered, first perform the following checks: Inspection While unpacking, inspect the product for damage during shipment, and make sure all bolts and nuts are tightened properly. Specification check Check the model number to make sure it is the product that was ordered. Be certain it is the correct voltage and frequency. Note: If there is any problem with the product as shipped, contact your nearest dealer or Wacker Neuson representative at once. Product specifications Do not operate this product under any conditions other than those for which it is specified. Failure to observe this precaution can lead to electrical shock, current leakage, fire, water leakage or other problems. WARNING If the pump is used to drain a swimming pool, the pump must be connected to a Ground Fault Interrupter (GFI). If the pump is used in fountains, the pump must be connected to a Ground Fault Interrupter (GFI). The pump must not be used when people are in the water. Leakage of pump lubricants may cause pollution of water. Proper plug must be provided according to local codes and standards. Refer to wiring diagram. DO NOT use this pump in liquids other than water, such as oil, salt water, or organic solvents. Use with a power supply voltage within ±5% of the rated voltage. DO NOT use in water temperatures outside the range of F (0 40 C) which can lead to failure, current leakage or shock. DO NOT use in the vicinity of explosive or flammable materials. Use only in fully assembled state. Note: Consult your local dealer or Wacker representative before using with any liquids other than those indicated in this document. Preparing for installation Before installing the pump at a work site, you will need to have the following tools and instruments ready: wc_tx000113gb.fm 9

10 Operation PS / PS / PSA Insulation resistance tester (megohmmeter) AC voltmeter AC ammeter (clamp-on type) Bolt and nut tighteners Power supply connection tools (screwdriver or box wrench) Note: Please also read the instructions that come with each of the test instruments. Checks to Make Before Installation When a three-prong grounded plug is used: Use the megohmmeter to measure the motor insulation resistance between the grounding prong and each one of the two power prongs. When connection wires are used: With the megohmmeter, measure the insulation resistance between the ground wire (Green) and each one of the two power wires. Reference insulation resistance: 20MΩ or greater. Note: The reference insulation resistance (20MΩ or greater) is the value when the pump is new or has been repaired. For the reference value after installation, see Maintenance and Inspection. DO NOT measure the insulation resistance with insulation resistance tester for the following parts. It will cause damage (Model PSA 2 500). CAUTION See Graphic: wc_gr Improper ways to measure insulation resistance 1. Between the plug prongs. 2. Between the electrodes on the level relay unit. 3. Between the electrodes on the level relay unit and the plug prongs. Precautions in Installation WARNING wc_tx000113gb.fm 10 wc_gr000258

11 PS / PS / PSA Operation When installing the pump, pay close attention to its center of gravity and weight. If it is not lowered into place correctly, it may fall and be damaged or cause injury. When transporting the machine by hand, be sure to employ manpower commensurate with the weight of the machine. To avoid back injury when lifting the machine, bend the knees to pick it up rather than bending your back only. Do not under any circumstances install or move the pump by suspending it from the cable assembly. The cable may be damaged, CAUTION causing current leakage, shock, or fire Avoid dropping the pump or other strong impact. Lift the pump by holding it firmly with the hands or by attaching a rope or chain to the lifting handle. Note: On cable assembly handling, see Electrical Wiring. Avoid dry operation, which will not only lower performance but can cause the pump to malfunction, leading to electrical leakage and shock. CAUTION Install the pump in a location with sufficient water level, where water collects readily. Note: See Operation ( Operating Water Level ) for the water level necessary for operation. Note: The discharge end of the hose should be located higher than the water surface. If the end of the hose is submerged, water may flow back to the pump when the pump is stopped; and if the hose end is lower than the water surface, water may overflow when the pump is turned off. If large quantities of earth are sucked up, damage resulting from friction in the pump can lead to current leakage and shock. CAUTION Use the pump in the upright position. To prevent the strainer from becoming submerged in mud, causing it to suck in sand or debris, mount it on a block or other firm base If used in a permanent installation where the pump is not readily accessible after installation, please contact Wacker Neuson for a duplicate nameplate to be installed at the wellhead or on the control box so that it will be readily visible. CAUTION DO NOT lift or hang the pump by the level relay unit (1). It will lead to damage and may cause leakage, electric shock, and fire (Model PSA 2 500). See Graphic: wc_gr wc_tx000113gb.fm 11

12 Operation PS / PS / PSA wc_gr Electrical Wiring WARNING Performing electrical wiring Electrical wiring should be performed by a qualified person in accord with all applicable regulations. Failure to observe this precaution not only risks breaking the law but is extremely dangerous. Incorrect wiring can lead to current leakage, electrical shock or fire. ALWAYS make sure the pump is equipped with the specified overload protectors and fuses or breakers, so as to prevent electrical shock from a current leak or pump malfunction. Operate within the capacity of the power supply and wiring. WARNING CAUTION WARNING CAUTION Grounding DO NOT use the pump without first grounding it properly. Failure to ground it can lead to electrical shock from a current leak or pump malfunction. DO NOT attach the grounding wire to a gas pipe, water pipe, lightning arrester or telephone grounding wire. Improper grounding can result in electrical shock. Connecting the power supply Before connecting wires to the terminal, make certain the power supply is turned off (circuit breaker, etc.), to avoid electrical shock, shorting, or unexpected starting of the pump, leading to injury. Before inserting the power supply plug, make certain the power supply is turned off (circuit breaker, etc.), to avoid electrical shock, shorting, or unexpected starting of the pump, leading to injury. Do not use the pump with the cable assembly or plug connected loosely, which can result in electric shock, shorting, or fire. wc_tx000113gb.fm 12

13 PS / PS / PSA Operation Draw power from a dedicated power outlet rated at 15 A or above. Sharing the outlet with other equipment may cause overheating at the branch outlet and could result in fire. The three-prong grounded plug shall be connected as shown in the drawing. NOTICE: Be sure to use a dedicated power supply with a ground leakage circuit breaker. Note: The shape of the plug may differ from that shown in the illustration. See Graphic: wc_gr and wc_gr W R G wc_gr CAUTION Cable Assembly If it is necessary to extend the cable assembly, use a core size equal to or larger than the original. This is necessary not only to avoid a performance drop, but to prevent cable overheating which can result in fire, electrical leakage or electrical shock. If a cable with cut insulation or other damage is submerged in the water, there is a danger of damage to the pump, electrical leakage, electrical shock, or fire. Be careful not to let the cable assembly be cut or become twisted. This may result in damage to the pump, electrical leakage, electrical shock, or fire. If it is necessary to submerge the connection wires of the cable assembly in water, first seal the wires completely in a molded protective sleeve, to prevent electrical leakage, electrical shock, or fire. DO NOT allow the cable assembly wires or power supply plug to become wet. Make sure the cable does not become excessively bent or twisted, and does not rub against a structure in a way that might damage it. If used in a deep-well installation, the cable assembly should be secured every twenty feet. wc_tx000113gb.fm 13

14 Operation PS / PS / PSA Electrical Circuit Diagrams See Graphics: wc_gr001201, wc_gr001202, and wc_gr R R 1 W W 5 2 B L 3 G G/Y 6 4 wc_gr PS POWER SOURCE SINGLE PHASE Ref. Description Ref. Description 1 Capacitor 6 Ground 2 Main coil 7 Circle thermal protector 3 Auxiliary coil 8 Float switch (normally open contact) 4 Miniature protector 9 Heater 5 Frame grounding Wire Colors B Black V Violet Or Orange G Green W White Pr Purple L Blue Y Yellow Sh Shield P Pink Br Brown LL Light Blue R Red Cl Clear G/Y Green/Yellow T Tan Gr Gray wc_tx000113gb.fm 14

15 PS / PS / PSA Operation 1 R B 2 3 R 4 W W 9 W W 5 6 B L 7 10 G G/Y 8 wc_gr PSA POWER SOURCE SINGLE PHASE Ref. Description Ref. Description 1. Level Relay Unit 6. Main Coil 2. Transformer 7. Auxiliary Coil 3. Electrode 8. Miniature Protector 4. Capacitor 9. Frame Grounding 5. Triac 10. Ground Wire Colors B Black V Violet Or Orange G Green W White Pr Purple L Blue Y Yellow Sh Shield P Pink Br Brown LL Light Blue R Red Cl Clear G/Y Green/Yellow T Tan Gr Gray wc_tx000113gb.fm 15

16 Operation PS / PS / PSA R R R R 2 W W G G L L 8 PS POWER SOURCE SINGLE PHASE 6 wc_gr Ref. Description Ref. Description 1. Circle Thermal Protector 5. Centrifugal Switch 2. Auxiliary Coil 6. Capacitor 3. Heater 7. Frame Grounding 4. Main Coil 8. Ground Wire Colors B Black V Violet Or Orange G Green W White Pr Purple L Blue Y Yellow Sh Shield P Pink Br Brown LL Light Blue R Red Cl Clear G/Y Green/Yellow T Tan Gr Gray CAUTION If connected to a circuit protected by a fuse, use a time-delay fuse with this pump. wc_tx000113gb.fm 16

17 PS / PS / PSA Operation Operation Before starting Make sure once again that the product is of the correct voltage and frequency rating. NOTICE: Using the product at other than rated voltage and frequency will not only lower its performance but may damage the product. Note: Confirm the rated voltage and frequency on the model nameplate Confirm the wiring, supply voltage, circuit breaker capacity, and motor insulation resistance. Reference insulation resistance = 20 MΩ or greater. Note: The reference insulation resistance (20 MΩ or greater) is the value when the pump is new or has been repaired. For the reference value after installation see Maintenance and Inspection The setting on the circuit breaker or other overload protector should be made in accord with the rated current of the pump. Note: See Operating Specifications for the rated current of the pump When powering the pump with a generator, be certain the generator is sized to supply the required power for the pump and any other equipment powered by the generator. WARNING WARNING Non-Automatic Models (PS 2 500, PS 2 750) Test Operation NEVER operate the pump while it is suspended in the air. The recoil may result in injury or other major accident. NEVER start the pump when people are standing next to it. A current leak can result in electrical shock. Run the pump for a short time (3 10 minutes) and confirm the following: Using an ammeter (clamp-on type), measure the operating current at the L1 and L2 phase wires on the terminal. COUNTERMEASURE: If the operating current exceeds the rated value, pump motor overload may be a cause. Make sure the pump has been installed under proper conditions as described in Installation. Using an AC voltmeter (tester), measure voltage at the terminals. Supply voltage tolerance: within ±5% of rated voltage. wc_tx000113gb.fm 17

18 Operation PS / PS / PSA CAUTION COUNTERMEASURE: If the supply voltage is outside the tolerance, possible causes are the power supply capacity or an inadequate extension cable. Look again at the wiring diagram and make sure the conditions are proper. In case of very excessive vibration, unusual noise or odor, turn off the power immediately and consult your nearest dealer or Wacker representative. Continuing to operate the pump under abnormal conditions may result in electrical shock, fire, or current leakage. WARNING Operation Make sure no extraneous objects such as pins, nails or other metal objects are sucked into the pump. These can damage the pump or cause it to malfunction, and can result in electrical shock or electrical leakage. When the pump is not used for an extended period, be sure to turn off the power (circuit breaker, etc.). Deterioration of the insulation may lead to electrical leakage, electrical shock, or fire. In case of a power outage, turn off the power to the pump to avoid having it start unexpectedly when the power is restored, presenting serious danger to people in the vicinity. CAUTION The pump may become hot during operation. Do not touch an operating pump. Allow the pump to cool before handling. Pay careful attention to the water level while the pump is operating. Dry operation may cause the pump to malfunction. Note: See section Operating water level, for the water level necessary for operation. If the protection system operates due to an overload or malfunction, causing the pump to stop, first investigate and remove the cause before restarting. CAUTION Operating water level Do not operate the pump below the C.W.L. (Continuous running Water Level) indicated below. Failure to observe this condition may result in damage to the pump, current leakage or electrical shock. wc_tx000113gb.fm 18

19 PS / PS / PSA Operation See Graphic: wc_gr a b C.W.L 115 mm (4-1/2") PS 2 500, PS PSA wc_gr Operating Water Level (PS 2 500, PS 2 750). Pump Model C.W.L. PS mm (2 ) PS mm (4 ) Operating water level (PSA only) Starting the Pump: This pump starts when water reaches the electrodes on the level relay unit, conducting current between them. Note: The necessary water level to operate the pump is 115 mm (4-½") from the bottom of the pump. To force start the pump for trial operation, short-circuit the electrodes (a) with a screwdriver (b) as illustrated. Please keep items that may clog the pump (such as wires, nails, cords, etc.) away from it. Motor Protection System (Motor Protector) Circle Thermal protector (PS 2 750) Miniature Protector (PS 2 500, PSA 2 500) The pump has a built-in motor protection system. If an excessive current is detected (PS 2 750) or the motor overheats, for reasons such as the following, the pump will automatically stop operating regardless of the water level, to protect the motor: Change in supply voltage polarity wc_tx000113gb.fm 19

20 Operation PS / PS / PSA Overload Open-phase operation or operation under constraint Note: Always determine the cause of the problem and resolve it before resuming operation. Simply repeating cycles of stopping and restarting will end up damaging the pump. Do not continue operation at very low lift, low water level, or while the strainer stand is clogged with debris. Not only will performance suffer, but also such conditions may cause noise, heavy vibration, and malfunctioning. Operating Cycle of Automatic Type (PSA 2 500). Stage Level Relay Unit Pump Water Level 1 When electrodes (b) of level relay units (a) submerge under water, the resulting electric current causes the pump to operate. (Electrodes sensing the electricity) 2 When the water level goes below the height of the electrodes, a timer is activated. The pump keeps operating. (No electric current >Timer activates.) 3 The pump keeps operating for approximately one minute. (The pump resumes the operation if the electrodes contact the water again within one minute.) 4 The pump stops one minute later. (The pump may not stop operating for a longer period of time.) 5 When the water level rises again and the electrodes touch the water, the pump starts operating again. (Electrodes sensing the electricity) See Graphic: wc_gr Operation starts (drainage) Operation remains (drainage) Operation remains (drainage) Operation stops Operation starts again (drainage) Falls Falls Falls Rises Falls wc_tx000113gb.fm 20

21 PS / PS / PSA Operation a a b 1 b wc_gr wc_tx000113gb.fm 21

22 Maintenance PS / PS / PSA Maintenance 3.1 Periodic Maintenance Table Pump Weekly Monthly Every 1000 hrs. Measure insulation resistance. Reference insulation resistance = 1MW or greater. (1) Measure operating current. Compare with rated current. Measure supply voltage. Compare with allowable range (within ±5% of rated voltage). Pump inspection. A noticeable drop in performance may indicate wear in the impeller, etc., or else clogging of the strainer, etc. Remove the clogged debris and replace any worn parts. Lubricant inspection. Change lubricant. Designated lubricant: SAE 10W/20W. (2) Change mechanical seal. (3) Overhaul. This should be carried out even if there are no problems with the pump. The frequency depends on how continuously the pump is in use. (4) Every 2000 hrs. (1) If the insulation resistance has become noticeably lower than the previous inspection, an inspection of the motor will be necessary. (2) See Lubricant Inspection and Lubricant Change in this section. (3) Specialized know-how is required for inspecting and replacing the mechanical seal. Consult with your nearest dealer or Wacker representative. (4) Consult with your nearest dealer or Wacker representative regarding overhauls. wc_tx000114gb.fm 22

23 PS / PS / PSA Maintenance and Inspection Maintenance Regular maintenance and inspections are a necessity for continued efficient functioning of the pump. If any abnormal conditions are noticed, refer to the Troubleshooting section and take corrective measures immediately. It is recommended that a spare pump be kept ready in case of any problems. Prior to inspecting Before inspecting the pump, make certain the power supply (circuit breaker, etc.) is turned off. Then, unplug the cable assembly from the receptacle or detach it from the terminals. Failure to follow this precaution may result in a serious accident from electrical shock or unexpected starting of the pump motor Washing the pump Remove accumulated matter from the surface of the pump and wash it with clean water. Take special care to remove any debris from the impeller Inspecting the pump exterior Look for any peeling or chipped paint, and make sure the nuts and bolts are fastened tightly. Any cracks in the surface should be repaired by cleaning that area, drying it and then applying a touch-up coating. Note: Touch-up paint is not supplied. Note that some kinds of damage or looseness may require that the unit be disassembled for repairs. Please consult your nearest dealer or Wacker representative. WARNING Storage When the pump is out of use for an extended period, wash it and dry it thoroughly, then store it indoors. Note: Always run a test operation before putting the pump back into service. If the pump is left in the water, it should be run a minimum of once a week. Inspecting Lubricant Remove the oil plug and tilt the pump to drain a small amount of lubricant. If the lubricant is milky white or has water mixed in with it, the mechanical seal may be faulty. In this case the pump will need to be disassembled and repaired. Replacing Lubricant Remove the oil plug and drain all the lubricant, then replace it with the specified amount. wc_tx000114gb.fm 23

24 Maintenance PS / PS / PSA Note: Worn lubricant and other waste products should be disposed of by a qualified agent, in accord with applicable laws. The oil plug gasket should be replaced each time the lubricant is inspected or changed. See Graphic: wc_gr wc_gr Ref. Description Ref. Description 1. Oil Inlet 3. Oil Plug 2. Gasket 4. Allen Wrench Pump Model PS PS 2 500, PSA PS Lubricant Capacity 160 ml (5.4 fl. oz.) 155 ml (5.2 fl. oz.) 210 ml (7.1 fl. oz.) Replacement Parts The table lists the parts that need to be replaced periodically. Replace these using the recommended frequency as a guideline. Part Mechanical seal Lubricant (SAE 10W/20W) Gasket Dust seal Sleeve Replacement Frequency When lubricant in oil compartment becomes milky. Every 2,000 hours or 12 months, whichever comes first. Each time pump is disassembled or inspected. When ring is worn, and each time pump is disassembled or inspected. When it becomes worn. wc_tx000114gb.fm 24

25 PS / PS / PSA Disassembly/Reassembly Maintenance WARNING Before disassembling the pump, make certain the power supply (circuit breaker, etc.) is turned off. Then, unplug the cable assembly from the receptacle or detach it from the terminals. To avoid electrical shock, DO NOT work with wet hands. NEVER check the operation of any parts (impeller rotation, etc.) by turning on the power while the unit is partially assembled. Failure to observe these precautions may result in a serious accident. DO NOT disassemble or repair any parts other than those designated here. If repairs are necessary in any other than the designated parts, consult your nearest dealer or Wacker representative. Improper repairs can result in electrical leakage, electrical shock, fire, or water leaks. After reassembly, ALWAYS perform a test operation before resuming use of the pump. Improper assembly will cause the pump to malfunction, resulting in electric shock or water leaks. The procedure for disassembly and reassembly is shown here to the extent necessary for impeller replacement. A specialized environment and facilities are necessary for work on the mechanical seal and the motor parts. Contact your nearest dealer or Wacker representative in the event such repairs are necessary. wc_tx000114gb.fm 25

26 Maintenance PS / PS / PSA Disassembly See Graphic: wc_gr Removing the strainer, suction cover, and volute: Remove the bolts (1) under the strainer (2), then remove the strainer, suction cover (3), and volute (4) Removing the Impeller: With a box wrench or other tool, remove the acorn nut (6), lockwasher (7) and washer (8), then remove the impeller (9), sleeve (10) and dust seal (11) from the shaft Removing the wear ring: Remove the wear ring (12) from the volute. A worn impeller may have sharp edges that can cause injury, and should be handled with care. WARNING Note: The exploded view shown is for model PS Other models may differ slightly in shape and structure wc_gr wc_tx000114gb.fm 26

27 PS / PS / PSA Reassembly See Graphic: wc_gr001206, wc_gr Maintenance Mount the dust seal (11) onto the outside of the sleeve (10) as shown in the drawing. When doing so, do not apply oil or other lubrication to the surface where the dust seal contacts the sleeve (a) When replacing the wear ring (12), make sure the front and back are oriented correctly. The side with the protrusions around the edge should face the volute (4). Press the wear ring firmly onto the surface Replace the dust seal and sleeve as one piece Align the impeller keyway with the rotor shaft keyway and push the impeller (9) onto the rotor shaft. Secure the impeller on the shaft with the washer (8), lockwasher (7), and acorn nut (6). While keeping the impeller and shaft from rotating, tighten the acorn nut Position volute (4) flush with oil housing. Assemble suction cover (3) and strainer (2) and secure the assembly with the three bolts (1). 11 a 10 wc_gr wc_tx000114gb.fm 27

28 Maintenance PS / PS / PSA Troubleshooting WARNING Before ordering repairs, carefully read through this manual, then repeat the inspection. If the problem remains, contact your nearest dealer or Wacker representative. ALWAYS turn off the power before inspecting the pump. Failure to observe this precaution can result in serious accident. Problem / Symptom Reason / Remedy Pump will not start Power is off. Restore power. Cable assembly is cut or not connected properly. Repair/ replace the cable or fix the connection. Plug is not inserted. Connect the plug. Impeller is clogged. Inspect the pump and remove any debris. Start float does not operate. Remove any obstruction and check the float operation. Pump stops soon after starting (Motor protector operates) Low voltage. Provide the rated voltage, or make sure the Impeller is clogged. Remove debris. cable assembly extension is the proper standard. Wrong power frequency. Check the nameplate, and replace the pump or the impeller. Extended operation with a clogged strainer. Remove debris from the strainer. Faulty motor (burning, water infiltration, etc.). Repair or replace the motor. Motor protection system was triggered. Identify and correct cause before re-starting. Poor lift or discharge capacity Worn out impeller or suction cover. Repair or replace the worn parts. Sharply bent or clogged hose. Straighten out any sharp bends. Enclose the pump with a screen to keep away debris. Strainer clogged or buried. Remove debris from the strainer, or place a block under the pump. Wrong power frequency. Check the nameplate, and replace the pump or the impeller. Heavy vibration or noise Damaged motor shaft. Contact dealer and replace motor. Pump will not stop automatically Something is interfering with the float operation, or the float switch is faulty. Remove any obstacles, or replace the switch. wc_tx000114gb.fm 28

29 PS / PS / PSA Notes Maintenance wc_tx000114gb.fm 29

30 Technical Data PS / PS / PSA Technical Data 4.1 Standard Specifications Machines discussed in this manual: Machine PS PSA PS BOM Applicable Liquids, Consistency and Temperature Rain Water, Fountain Water, Ground Water, Sand-Carrying Water 0 40 C ( F) Pump Impeller Semi-Vortex Type: (PS 2 500, PSA 2 500) Open Type: (PS 2 750) Shaft Seal Bearing Double Mechanical Seal Shielded Ball Bearing Motor Specification Dry Submersible Induction Motor (2-Pole) Insulation Class E Protection System Miniature Protector: (PS 2 500, PSA 2 500) Circle Thermal Protector: (PS 2 750) Lubricant SAE 10W/20W Such as: Turbine Oil ISO VG #32 Shell Victrolia Oil #27 British Pet Energol THB #32 Gulf Paramount #32 Tellus #T22 Shell Oil Shell Turbo T32 Connection Coupling (NPT 2 ) wc_td000035gb.fm 30

31 PS / PS / PSA Operating Specifications (60 Hz) Technical Data Part No. PS PSA PS Pump Electric Power V/Ph/Hz 110/1/60 220/1/60 110/1/60 110/1/60 220/1/60 Rated Current A Starting Method Capacitor-Run Bore mm (in.) 50 (2) Output kw (Hp) 0.48 (0.66) 0.75 (1) Maximum Head m (ft.) 12 (39.5) 18 (60) Maximum Capacity L/min (GPM) 236 (62.4) 276 (73) Maximum Pressure psi Solid Size Capacity mm (in.) 6 (0.2) Weight* Kg (lbs.) 9.5 (21) 10 (22) 16 (35) * The weight (mass) given above is the operating weight of the pump itself, not including the cable assembly. 4.3 Dimensions 185 (7.3) 185 (7.3) 185 (7.3) 185 (7.3) 185 (7.3) 222 (8.8) 200 (11) 229 (9) 305 (12) 200 (11) 229 (9) 305 (12) 414 (16.3) PS PSA PS wc_gr wc_td000035gb.fm 31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46 Wacker Construction Equipment AG Preußenstraße 41 D München Tel.: +49-(0) Fax: (0) Wacker Neuson Corporation P.O. Box 9007 Menomonee Falls, WI Tel. : (262) Fax: (262) Tel. : (800) Wacker Asia Pacific Operations Skyline Tower, Suite 2303, 23/F 39 Wang Kwong Road, Kowloon Bay, Hong Kong Tel Fax: