TP24TSCRUB REV: TP

Transcription

1 TPTSCRUB REV: TP

2 TABLE OF CONTENTS SAFETY PRECAUTIONS MACHINE COMPONENTS MACHINE SET UP 5 MACHINE INSTALLATION 5- MACHINE OPERATION TANK DRAINING 7 BATTERY CHARGING 7- PREVENTATIVE MAINTENANCE -9 MACHINE STORAGE 9 BASIC TROUBLESHOOTING 0 PARTS BREAKDOWNS AND LISTS -7 WIRING DIAGRAM

3 Please read and save these instructions. Read carefully before attempting to assembly, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. TASK-PRO SAFETY PRECAUTIONS Automatic Scrubber This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only with recommended accessories. All operators shall read, understand and exercise the following safety precautions: ) DO T OPERATE MACHINE: Unless trained and authorized. Unless you have read and understand the operators manual. In flammable or explosive areas. If not in proper operating condition. In outdoor areas. ) BEFORE OPERATING MACHINE: Make sure all safety devices are in place and operate properly. ) WHEN USING MACHINE: Go slow on inclines and slippery surfaces. Follow all safety guidelines. Be very careful when using the machine in reverse. Report and fix any damage to machine prior to operating it. ) BEFORE LEAVING OR SERVICING MACHINE: Stop machine on level ground. Turn machine off. 5) WHEN SERVICING MACHINE: Read operators manual thoroughly prior to operating or servicing this machine. Use manufacturer supplied or approved replacement parts. Secure machine with wheel blocks prior to jacking the machine up. Use approved jack or hoist to safely elevate the machine. ) WHEN SERVICING MACHINE: (con t) Disconnect batteries prior to working on machine. Wear gloves when handling batteries or battery cables. Avoid any contact with battery acid. Avoid moving parts. Do not wear loose fitting clothing while servicing machine. Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging. Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks. Flammable materials or reactive metals can cause explosion or fire. Do not pick up.

4 MACHINE COMPONENTS Main power ON/OFF switch. Vacuum ON/OFF switch. Battery level meter. Brush ON/OFF switch 5. Brush pressure meter. Solution ON/OFF switch 7. Brush pressure UP/DOWN switch. Solution control knob 9. Speed control knob 0. Circuit breakers. Recovery tank drain hose. Squeegee adjustment nut & shaft. Squeegee assembly. Scrub head actuator 5. Solution tank level sight tube. Console adjustment levers 7. Rear solution fill. Reverse switch 9. Squeegee lift lever 0. Control housing. Operating triggers. Solution tank. Rear casters. Transport wheels 5. Scrub head. Scrub head skirt 7. Skirt housing latch. Protective rollers 9. Front solution fill 0. Recovery tank. Recovery tank lid

5 MACHINE SET UP & INSTALLATION UNCRATING MACHINE Be sure and check packing carton for any damage. Immediately report any damage to carrier. Check contents of package to ensure that the following items are included: Machine, batteries (x), squeegee assembly, battery charger, and pad driver. BATTERY CONNECTIONS The batteries and charger are shipped separately and will need to be installed and connected as shown in the diagram below. Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging.. Be sure power switch is in the off position.. Open recovery tank to gain access to battery compartment.. Carefully place the two batteries into the compartment as shown in figure below. Place the battery brace at the rear of the two batteries. DO T DROP BATTERIES INTO COMPARTMENT!. Connect battery cables to posts in numbered order as shown in drawing below. (RED to POSITIVE and BLACK to NEGATIVE) MACHINE SET UP PRE-OPERATION CHECKS. Sweep or dust mop the surface to be cleaned.. Check battery meter to make sure batteries are fully charged. (see BATTERY CHARGING). Check that squeegee is properly installed.. Check that brush / pad is properly installed. INSTALLING PAD DRIVER OR BRUSH. Ensure that the machine is turned off. Raise the brush head assembly off the floor by pushing on the brush lift button on the control console.. Open the swing away skirts to gain access to the brush head assembly.. If using a pad driver, first attach the appropriate pad to the pad driver surface. 5. Mount the pad driver or brush to the drive motor hub by lining up the three studs with the three holes in the drive motor hub. Once in the holes, rotate the driver toward the spring clip to lock driver into place. MOUNTING THE SQUEEGEE. Pull back on the squeegee lift lever to raise the squeegee bracket up.. Loosen the two knobs on the squeegee and slide the squeegee into the slots at the rear of the squeegee bracket. (the wheels on the squeegee point to the back). Tighten the knobs securely.. Secure the vacuum hose on the pick-up tube of the squeegee. RED BLACK BATTERY BRACE CHARGER PLUG 5. Apply a coat or protective spray on the cable connections to prevent battery corrosion. FILLING THE SOLUTION TANK. The NEL can be filled in two different locations: a. Front fill area for use with a hose or a bucket. b. Rear fill area for use with a hose only.. Determine which fill area you would like to use to fill the machine with water. 5

6 . Fill solution tank with up to 7 gallons of water. (water temperature should not exceed 0 F) The clear tube in the back left of the machine has gallon markers to help determine the water level in the solution tank. If you are filling the solution tank with a bucket, make sure the bucket is clean. This will prevent debris from clogging the lines or solenoid. Do not put any flammable materials into solution tank. This can cause an explosion or a fire. Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals. MACHINE OPERATION Do not operate machine unless you have read and understand this manual.. Set control housing to a comfortable operating height by squeezing together the two thumb levers directly underneath the housing. (see machine components, item #). Lower squeegee assembly to the floor by releasing the lift lever from its locked position. (see machine components, item #9). Lower the brush head assembly to the floor by pushing on the brush lift button on the control console. (see machine components, item #7). Turn main power to on position. (see machine components, item #) 5. Turn vacuum motor switch to on position. (see machine components, item #). Turn the brush motor switch to on position. (see machine components, item #) a. Brushes will not spin until the operating triggers are pulled. 7. Turn the solution switch to on position. (see machine components, item #) a. Solution will not begin to flow until the operating triggers are pulled.. To begin scrubbing, pull on one or both of the red operating triggers. (see machine components, item #) When these triggers are pulled, the brush will begin to spin, the solution will begin to flow, and the machine will propel itself. 9. This machine is self-propelled. The speed can be controlled by a dial located on the right side of the control housing. (see machine components, item #9) 0. This machine has reverse. In order to activate reverse, there is a toggle switch located on the left side of the control housing. (see machine components, item #) The toggle switch must be pulled backwards and the red operating triggers must be pressed to activate reverse motion. Do not keep the machine in the same position with the pad / brush spinning, or you could cause damage to the floor.. Adjust amount of solution flow by turning the solution control knob. Turn to the right for more solution, or turn left for less solution. (see machine components, item #) WHILE OPERATING MACHINE. Occasionally look through the clear recovery tank lid to see if there is any foam build-up. If excessive foam is found, add defoamer to the recovery tank. Foam must not enter the float shut-off screen, or damage can occur to the vacuum motor. Foam will not activate the machines float shut-off device.. Occasionally view the clear tube at the back left of the machine to check the amount of cleaning solution that is left in the machine.. Occasionally check the battery level meter. (see machine components, item #) When meter is in the red, recharge the batteries. When battery meter is in the red, do not continue to operate the machine. Battery damage may result.. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the blades down with a damp cloth. Do not use your fingers to wipe or remove debris from the blades, as injury may occur.

7 5. When the solution tank runs empty, turn off the brush switch, solution switch and raise the brush head. Keep the squeegee down and continue to vacuum until all the dirty water is picked up. (see TANK DRAINING section to learn how to drain recovery and solution tanks) The brush motors are circuit breaker protected to protect them from damage. If a breaker trips, it can t be reset immediately. You must first determine what caused the breaker to trip, and allow the motor to cool down before you can reset the breaker. The breakers are located on the back panel of the control housing. TANK DRAINING. Turn the power off on the machine. With the squeegee and brush head in their up position, transport machine to approved area for draining tank(s). DRAINING THE RECOVERY (DIRTY) TANK Anytime scrubbing is completed, or when refilling solution tank, the recovery tank should be drained and cleaned. If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shut-off mechanism and cause damage to the vacuum motor.. Remove the drain hose from the holder, and place the drain hose over the floor drain. Twist off the drain hose plug to begin the draining process. In order to completely empty the recovery tank, hinge open the recovery tank and let it rest on the support stand.. Clean the recovery tank after every use. Use a fresh water hose to rinse out the recovery tank. Be careful not to spray water into the float shut-off mechanism. If you are storing the machine for any period of time, always leave the clear recovery tank lid off the tank so the tank can dry completely and smell fresh.. Replace the drain hose plug tightly as soon as you are done draining the tank. DRAINING THE SOLUTION (CLEAN) TANK Anytime scrubbing operation is completed, the solution tank should be drained and cleaned.. Pull down on the clear tube (back left of the machine) to remove it from the hose barb. This will allow the solution to flow freely into a bucket or floor drain.. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines.. With clean water in solution tank, turn machine power on, solution switch on and pull the operating triggers. This will allow the clean water to flush through and clean the solution plumbing.. Once tank is rinsed, flushed and drained, reconnect the clear tube to the hose barb. Be sure the tube is pushed all the way up on the hose barb. BATTERY CHARGING Use only approved chargers with the following specifications: Automatic shut off circuit Deep cycle charging Output current of 0 0 amps Output voltage of volts For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition. 7

8 Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times. When charging the machine, make sure the battery compartment is left open.. Place charger and machine in a well ventilated area.. Turn machine off.. Open recovery tank up, exposing battery compartment. Check fluid level in each battery cell. Do not charge batteries unless fluid is slightly covering the battery plates. Do not overfill the batteries. Overfilling may cause the batteries to overflow during charging due to expansion. Replace the caps prior to charging. 5. Plug approved charger into grounded wall outlet before plugging the charger into the machine.. Plug charger into red charger receptacle located in the front left of the battery compartment. 0. Check the battery level after charging is complete. If fluid level is low, add distilled water to bring the fluid level up to the bottom of the sight tubes. Replace the caps and wipe the batteries down with a towel. PREVENTATIVE MAINTENANCE Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected! Repairs are to be completed by Authorized Service Centers only. Any repairs completed by unauthorized persons will void the warranty. DAILY MAINTENANCE. Remove pad driver / brush and clean with approved cleaner.. Drain recovery and solution tanks completely and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary.. Raise squeegee assembly off floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position.. Remove the float shut-off assembly and rinse it out with clean water. 7. Flip up the recovery tank kick stand and gently lay the recovery tank down until it rests on the stand.. The charger will automatically begin to charger the batteries, and it will automatically shut down once the batteries are fully charged. 9. Upon completion of charging, first unplug the charger from the wall outlet, and then disconnect the charger from the machine. 5. Clean machine with an approved cleaner and a damp towel.. Recharge batteries.

9 WEEKLY MAINTENANCE. Check fluid level in batteries.. Check batteries for loose or corroded cables.. Keep battery tops clean from corrosion. MONTHLY MAINTENANCE. Check machine for leaks and loose fasteners.. Lubricate all grease points and pivot points with silicon spray and approved grease.. Place machine over a floor drain. Flush solution system by pouring gallons of hot water and approved alkaline detergent into the solution tank and running machine (with solution control on) for 5 seconds. Turn machine off and let it sit overnight. Then next day, drain the remaining solution and rinse the solution tank out with clean water. VACUUM MOTOR MAINTENANCE. Contact your local Distributor for any motor maintenance.. Vacuum motor should have the brushes checked every 50 hours. Brushes should be replaced when they are worn to a length of 0mm or less. BATTERY MAINTENANCE For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition. Batteries are dangerous! Batteries emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times.. Always follow the battery charging directions as outlined in the BATTERY CHARGING section of this manual.. Keep battery tops and terminals free from corrosion. A strong solution of baking soda and water is the best way to keep the batteries corrosion free. DO T ALLOW THE BAKING SODA / WATER SOLUTION TO ENTER THE BATTERY CELLS.. Use a wire brush with the baking soda solution to properly clean the battery posts and connections.. Check battery connections for wear and loose terminals. Replace if necessary. MACHINE STORAGE. Always store the machine indoors.. Always store the machine in a dry area.. Always store the machine in its upright position.. Always store the machine with the pad driver / brush raised off the floor. 5. Always store the machine with the squeegee assembly raised off the floor.. If storing in an area which may reach freezing temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused by freezing temperatures will not be covered by the warranty. 7. Drain the recovery tank and remove the clear on the top of the recovery tank so that it can breathe during storage.. Drain the solution tank of all fluid. Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times! 9

10 BASIC TROUBLESHOOTING PROBLEM CAUSE SOLUTION No power Bad batteries Replace batteries Batteries need to be charged Charge batteries (see Battery Charging) Loose battery cable Tighten loose cable(s) Batteries not connected properly Follow battery installation instructions Brush motor does not run Bad brush switch Contact Distributor Brush circuit breaker has tripped Check brush motor for obstructions and reset breaker Rectifier has burned out Contact Distributor Bad wiring Contact Distributor Bad brush motor Contact Distributor Carbon brushes worn out Contact Distributor Bad solenoid Contact Distributor Vacuum motor does not run Bad vacuum switch Contact Distributor Bad wiring Contact Distributor Bad vacuum motor Contact Distributor Carbon brushes worn out Contact Distributor Short run time Batteries need to be charged Charge batteries (see Battery Charging) Batteries need maintenance See Battery Maintenance in this manual Bad cell in battery(s) Replace batteries Bad charger Replace charger Little or no solution flow Bad solution switch Contact Distributor Clogged solution solenoid Contact Distributor Clogged solution filter Remove filter and clean Solution line obstructed Remove solution line and clean Increase flow by twisting solution adjustment knob to the Solution flow adjustment knob in need right. Decrease flow by twisting solution adjustment knob of adjustment to the left. Poor water pick up Squeegee clogged Clean debris off squeegee with damp towel Squeegee blades worn Install new squeegee blades Squeegee not mounted correctly Confirm that the squeegee assembly is securely fastened to the machine and not loose fitting. Vacuum hoses have a hole or are loose Check hose connections and make sure they are firm. Replace hose if damaged. Vacuum hose may be clogged Check hose for debris and remove any clog. Drain hose stopper is loose Tighten drain plug. Batteries need to be charged Charge batteries (see Battery Charging) Vacuum motor is loose Tighten vac motor mounting screws. Do not overtighten or damage will occur. Recovery tank lid is loose Recovery tank inlet hole is clogged Recovery tank is full Float shut off is clogged Confirm the clear recovery tank lid is securely in place. Drain recovery tank and tilt tank on side. Check the inlet hole for debris and remove debris. Drain recovery tank. Remove float shut off from inside recovery tank and remove any debris. 0

11

12 DIA PART NUMBER SOLUTION TANK ASSEMBLY DESCRIPTION REQ'D VF05BD GRIP,HANDLE VA77 SCREW, SELF-TAPPING, ST, M X VV WASHER,PLAIN, M X M X VV0 SCREW, M X 0 5 VF59 WASHER,LOCK, M5 X M X VF5 PLUG,EXPANSION 7 VF55 WASHER,PLAIN, M X M0 X VF0 BUSHING 9 VF0 SUPPORT,RECOVERY TANK 0 VF09A BRACKET,VAC TUBE VF0 SPRING VF00 ADAPTER,TUBE VF0A GASKET,TUBE ADAPTER VF070TP LABEL,LEFT 5 VF0 CONNECTOR, 75A VF77 WIRE, # X VF DECAL VF SCREW, M X 5 9 VV07 WASHER,LOCK, M 0 GT0 WASHER,PLAIN, M X M X.5 VF7 WIRE, # X 750 VF95 SCREW, M X VF75 STANDOFF VF07 BRACKET 5 VF SCREW, M X 0 VF07 SCREEN,FILL 7 VF5 SCREW, SELF-TAPPING, ST, M X VF5 SCREW, SELF-TAPPING, ST, M X 0 9 VA WASHER,PLAIN, M X M9 X VF0 PLUG,FILL SCREEN VF079 COVER,FILL SCREEN VF0 SOLUTION TANK VF07TP LABEL,RIGHT VF9900 WHEEL, " 5 VF9 BUSHING VF5A WASHER,PLAIN, M X M.5 X 7 VF5 SCREW, M X 50 BAT95I BATTERY,V,95AMP HOUR 9 VF CASTER, "

13 DIA PART NUMBER SOLUTION TANK ASSEMBLY DESCRIPTION REQ'D 0 VF0 TRAY,BATTERY VF07A SPACER,BATTERY VF SCREW, M0 X 0 VF0 CABLE,BATTERY VF7 CAPS,BATTERY,BLACK VF7R CAPS,BATTERY,RED 5 CHRGR CHARGER,V,AMP VF57 WASHER,PLAIN, M0 X M X 7 VF5 WASHER,LOCK, M0 VF SCREW, M X 9 VF5 NUT, M 50 VF0 PLATE,LOCK 5 VF HOSE BARB 5 VF CLAMP (-5) 5 VFB TUBING 5 VF0 SCREW, M5 X 5 55 VV0 WASHER,LOCK, M5 5 VF5 WASHER,PLAIN, M5 X M X 57 VF0 PLATE,SQGE,LOCK 5 VF5 SCREW, M X 5 59 VF WASHER,LOCK, M.7 0 VF HANDLE,SQGE,LIFT VF050A BUSHING VF SCREW, M X 00 VA5 WASHER,PLAIN, M0 X M0 X.5

14

15 DIA PART NUMBER RECOVERY TANK ASSEMBLY DESCRIPTION VF0 RECOVERY TANK 9 VF5 WASHER,TOOTH,LOCK, M 0 VF95 SCREW, M X VF0 CABLE VF509 PLUG,EXPANSION VF50-9 STRAP,DRAIN HOSE VF50- SLEEVE,DRAIN HOSE 5 VF50A DRAIN HOSE ASSEMBLY VV0 CLAMP, " 7 VF5 DECAL,BATTERY INSTALLATION ZD5000 MOTOR,VAC STAGE,VDC 9 VF50 NUT,LOCK, M 0 VF50 STUD VF0TP LOGO,TASK-PRO REQ'D VF00 CLEAR COVER,RECOVERY TANK VF0 DECAL WARNING BATTERY VF009 ELBOW ADAPTOR,FLOAT VV07 WASHER,LOCK, M 5 VF5 WASHER,PLAIN, M X M X 7 VF SCREW, M X 0 7 VF50 FLOAT VF5 NUT,M VF50 SEAT VF00 SCREW, M X 9 GT0 WASHER,PLAIN, M X M X VF0 HINGE,RECOVERY TANK 7 VA77 SCREW, SELF-TAPPING, ST, M X VV WASHER,PLAIN, M X M X 9 VF00A RUBBER HINGE 0 VF00B GASKET VF00X KIT,LID 5

16

17 DIA PART NUMBER VF00TP 5 VF7 REQ'D VF0 WHEEL, " BRUSH LIFT/DRIVE ASSEMBLY DESCRIPTION HUB CAP VF00 TRANSAXLE ZD7000A TRANSAXLE MOTOR, VDC VF0 BRACKET,TRANSAXLE MOUNT 5 VF57 WASHER,PLAIN, M0 X M X VF5 WASHER,LOCK, M0 7 VF SCREW, M0 X 5 VF SCREW, M0 X 0 9 VF50 NUT,LOCK, M 0 VF5 WASHER,PLAIN, M X M X VF0 SPACER VF0A BUSHING VF5 WASHER,PLAIN, M X M X VF BRACKET,LIFT DUAL MOTOR 5 VF9 PIN, M0 X 0 VF0 PIN,COTTER, M. X 7 VF0 ACTUATOR VF59 WASHER,LOCK, M 9 VV0 SCREW, M X 0 0 VF55 WASHER,PLAIN, M X M0 X VF BRACKET,CABLE GUIDE VF5 BRACKET,ACTUATOR VF5 PLATE VF7 SCREW, M X 5 PLATE,BASE TRANSAXLE VF50 NUT,LOCK, M 7

18

19 DIA PART NUMBER BRUSH/PAD DRIVE ASSEMBLY DESCRIPTION REQ'D VFA BLOCK,GUIDE VV07B WASHER,PLAIN, M X M9 X VA00 WASHER,PLAIN, M5 X M X GT0 NUT,LOCK, M5 5 VF SCREW, M X VF59 WASHER,LOCK,M 9 7 VF5 WASHER,PLAIN, M X M X VFA SUPPORT PLATE,SKIRT 9 VF55 WASHER,PLAIN, M X M0 X 0 VF BRACKET,SPRING VF7 SPRING VA0 PIN, M X 0 VFA BRACKET,SPRING MOUNT VF BRACKET,MOTOR MOUNT 5 VF TUBING, 50mm VF00 HOSE BARB,TEE 7 VF TUBING, 0mm VF CLAMP, mm 9 VF5A SCREW, M X 0 0 VF STUD VF PAD DRIVER, " VF50 NUT,LOCK, M VF SPACER VF9900A BIG MOUTH 5 VA SCREW,SELF-TAPPING,ST, M X MF-VF00-A SCREW,SELF-TAPPING, /" - " 7 VF SCREW, 5/" - " VV09 WASHER,LOCK, 5/" 9 VF05 WASHER 0 VF0A PLATE, DRIVE, ASSY VF0 PLATE,DRIVE VF STOP,DRIVE RELEASE VF SPRING VF CLAMP,BRUSH PLATE 5 VV0 WASHER,LOCK, M5 VF55 SCREW,SELF-TAPPING,ST,M5 X 0 7 VV0 SCREW, MX0 VF SCREW, /" - " 9 VV0 WASHER,LOCK, /" 0 VF57 WASHER,PLAIN,M0 X M X VF PIN, M X ZD507 KEY,.5 X 5 ZD5000 BRUSH MOTOR,VDC,.75HP VF0 SCREW, M5 X 5 9

20 0

21 DIA PART NUMBER SOLUTION CONTROL ASSEMBLY DESCRIPTION REQ'D VF5 SCREW, M5 X VF0 SHAFT VV50 SCREW, M X 0 VF5 WASHER,PLAIN, M5 5 VV0 WASHER,LOCK, M5 VF0 SCREW, M5 X 5 7 VF5 WASHER,PLAIN, M9. X M X VF075 NUT, /" 9 VF CABLE,SOLEID 0 VF CLAMP, mm VF00 HOSE BARB,TEE VF TUBING, 50mm VF0 ELBOW VF TUBING, 5mm 5 VF0A ELBOW,SOLUTION TANK VF70 TIE 7 VF- HOSE BARB, FILTER VF- SEAT, FILTER 9 VF- SCREEN, 0SS,FILTER 0 VF-5 GASKET, FILTER VF- COVER, FILTER VF FILTER, ASSY VF5 TUBING, 00mm VF TUBING, 0mm 5 VF95 SCREW, M X VF5 WASHER,PLAIN, M X M X 7 VF7 TUBING, 5mm VF0- SOLUTION VALVE SOLEID,VDC 9 VV07 WASHER,LOCK, M 0 VF0 BRACKET,SOLEID VF50 NUT,LOCK, M VF TUBING, 0mm VV0509 SCREW, M5X0 VF CLAMP 5 VF50 WASHER,WAVE, M VF07 BRACKET,DRAIN HOSE & VALVE 7 VF09 LABEL,VALVE VF07 BUSHING 9 VF0BD KB,VALVE ADJUST

22

23 DIA PART NUMBER BRUSH SKIRT ASSEMBLY DESCRIPTION REQ'D VF05 BUMPER VF95 SCREW, M X VV07 WASHER,LOCK, M VF5 WASHER,PLAIN, M 5 VF07 BRACKET,SKIRT MOUNT VF0 PIN,SKIRT 7 VF0 WHEEL, " VF055 BUSHING 9 VF5A WASHER,PLAIN, M X M.5 X 0 VF SCREW, M X 0 VA7 SCREW, M5 X VF550 WASHER,PLAIN, M5 X M5 X.5 VF5 CLAMP,BUMPER VA00 WASHER,PLAIN, M5 X M X 5 VF7 GRIP,BUMPER VF05A BUMPER 7 VF0R RIGHT SKIRT,ASSEMBLY VV059 SCREW, M X 9 VF0 SKIRT,RIGHT 0 VF09 LATCH,HOOD VV09 WASHER,LOCK, M VF0 SKIRT,LEFT VF BLOCK,SKIRT VF0L LEFT SKIRT,ASSEMBLY

24

25 DIA PART NUMBER CONTROL HOUSING DESCRIPTION REQ'D VF9 SCREW, M X 7 VF WASHER,PLAIN, M0 X M0 X VF SCREW, M0 X 5 VF50 NUT,LOCK, M 0 5 GT0 WASHER,PLAIN, M VF7 DIODE, 00V VF7-X DIODE WITH ENDS 7 VF7A SOLEID, V VF7 BREAKER,CIRCUIT, 5 AMP 9 VF9 LABEL,CIRCUIT BREAKER 0 VF0 HOUSING,CONTROL VF7 BUSHING VF05 LABEL,SPEED CONTROL VF07 SCREW,M X 0 VA5077 WASHER,PLAIN, M X M0 X 5 VF7 LIGHTS,BATTERY CAPACITY VF GASKET 7 VF95 SCREW, M X VF79 SPACER 9 VF7A PANEL,SWITCH 0 VF0TP LABEL,SWITCH VF7 SWITCH,LIGHTED ROCKER VF77 GAUGE,BRUSH PRESSURE VF75 SWITCH,BRUSH LIFT VF00 SCREW, M X 5 VF70 KB,SPEED CONTROL VF709 PIN,HANDLE LOCK 7 VF7 SPRING VF70 PIN,HANDLE ADJUSTMENT 9 VF79 POTIENTIOMETER,.7K 0 VF PLATE VF79-T SPEED CONTROL,BOARD VF5TP SERIAL TAG VF LABEL,CIRCUIT BREAKER VF0A PANEL,CONTROL HOUSING 5 VF70 BATTERY CAPACITY CONTROL,BOARD VF GASKET 7 VF990 BREAKER,CIRCUIT, AMP VF07BD HANDLE,RIGHT 9 VF7 BOLT,SHOULDER, M X 5 X M 0 VF7 SPRING VF5A WASHER,PLAIN, M X M.5 X VF0BD HANDLE,LEFT VF SCREW, MX5 VF5 WASHER,TOOTH, M 5 VF0 SWITCH ASSY VF707 BRACKET,SWITCH 7 VV5 NUT,LOCK, M VF7 TUBE,HANDLE,ADJUSTMENT 9 VF5 SWITCH,KEY 50 VF0 LABEL,KEY SWITCH 5 VF7B STRAIN RELIEF,CORD 5 VF7 SWITCH,TOGGLE 5

26

27 SQUEEGEE ASSEMBLY DIA PART DESCRIPTION VF50 NUT,LOCK, M VF5 WASHER,PLAIN, M X M X VF7 LOCK SPRING VF7 SCREW, M X 0 5 VF FRONT SQUEEGEE SUPPORT VF57 NUT LOCK M0 7 VF CABLE,SQGE,LIFT (") VF BUSHING 9 VF0A HOSE 0 VF50 HOLDER,"U" HOSE VF50 HANDWHEEL Mx55 VF5 WASHER NYION VF50 SQUEEGEE SUPPORT PIN VF0 KB, M 5 VF SCREW,M X 0 VF5A WASHER,PLAIN, M X M.5 X 7 VF055 BUSHING VF0 WHEEL, " 9 VF0 HOUSING,SQUEEGEE (FANG T & T) VF HOUSING,SQUEEGEE (FANG T) VF0 BLADE,SQUEEGEE,REAR,PU (FANG T & T) 0 VF BLADE,SQUEEGEE,REAR,NEOPRENE (FANG T & T) VF7 BLADE,SQUEEGEE,REAR,PU (FANG T) VF5 BLADE,SQUEEGEE,REAR,NEOPRENE (FANG T) VFA LATCH,HOOD VF09 HOOK,REAR SQUEEGEE BACKUP ADJUSTMENT VF0 SCREW, M5 X 70 VF0 RIVET, M X 5 5 GT0 NUT,LOCK, M5 VF BOLT,SHOULDER, 5/" X.5" 7 VF9 WHEEL, " VF55 WASHER,PLAIN, M X M0 X 9 VV00 NUT,LOCK, 5/" 0 VF BACKUP STRIP,SQUEEGEE,REAR (FANG T & T) VF BACKUP STRIP,SQUEEGEE,REAR (FANG T) VFA KIT,BACKUP STRIP (FANG T & T) VFA KIT, BACKUP STRIP (FANG T) VF05 BLADE,SQUEEGEE,FRONT,PU (FANG T & T) VF5 BLADE,SQUEEGEE,FRONT,NEOPRENE (FANG T & T) VF BLADE,SQUEEGEE,FRONT,PU (FANG T) VF BLADE,SQUEEGEE,FRONT,NEOPRENE (FANG T) VF BACKUP STRIP,SQUEEGEE,FRONT (FANG T & T) VF BACKUP STRIP,SQUEEGEE,FRONT (FANG T) VF KB, M 5 VF50 NUT,LOCK, M VF50 NUT LOCK M 7 VF5 NUT, M VF50 SPACER x0x7 9 VF00A SQUEEGEE ASSY (FANG T & T) VF00B SQUEEGEE ASSY (FANG T) 0 VF5 NUT LOCK M VF5 WASHER PLAIN.X X VF5 BACK SQUEEGEE SUPPORT VF57 SEREW SHOULDER M0 VF SEREW SHOULDER M 5 VF7 SQUEEGEE SUPPORT VF500 KIT, SQUEEGEE BRACKET ASSEMBY 7

28 (AWG WHT) BATTERY CAPACITY LIGHTS 0 (AWG BLU) (AWG RED) 9 AMMETER (AWG RED) MAIN SWITCH VACUUM SWITCH BRUSH SWITCH SOLUTION 7 SWITCH UP (AWG WHT) KEY SWITCH MAIN CIRCUIT BREAKER (AWG WHT) AMP 0 (AWG WHT) (AWG GRN) (AWG RED) (AWG BLK) (AWG RED) (AWG BLK) (AWG RED) 0 (AWG RED) (AWG RED) (AWG RED) 7 (AWG BLU) (AWG BLU) (AWG WHT) TRIGGER SWITCH (AWG WHT) 5 SPEED CONTROL BOARD BRUSH SOLEID B+B- M M RIGHT BRUSH CIRCUIT BREAKER 0 (AWG BLU) 0 (AWG BLU) 0 (AWG BLU) 9 (AWG RED) 9 (AWG RED) (AWG WHT) 5AMP 5AMP LEFT BRUSH CIRCUIT BREAKER F R DIRECTION SWTICH.7K W B B PCB ACTUATOR (AWG BLU) 0 DOWN (AWG GRN) (AWG GRN) SOLUTION SOLEID (AWG RED) 0 (AWG RED) (AWG RED) 0 (AWG BLU) ACTUATOR MOTOR 0 (AWG BLK) LEFT BRUSH MOTOR 0 (AWG BLK) RIGHT BRUSH MOTOR 0 (AWG BLK) VACUUM MOTOR 5 (AWG WHT) (AWG RED) (AWG RED) DRIVE MOTOR (AWG BLK) (AWG RED) (AWG RED) (AWG WHT) (AWG RED) 0 (AWG BLU) CHARGER PLUG (AWG RED) (AWG BLK) (AWG BLU) 0 (AWG BLK) 0 (AWG GRN) 0 (AWG BLK) 0 (AWG BLK) 0 (AWG BLU) 0 (AWG BLK) 0 (AWG RED) (AWG RED) (AWG RED) VACUUM SOLEID 5AMP VACUUM CIRCUIT BREAKER (AWG RED) (AWG RED) V BATTERY V BATTERY CHARGER PLUG (AWG RED) (AWG BLK) (AWG WHT) 0 (AWG BLU) (AWG RED) MAIN SOLEID

29 说明书修改内容说明第一页更改版次和时间 7 页编号 5 更改代码更换,7, 页