Installationsplan / Installation plan PW 6161 EL

Transcription

1 Installationsplan / Installation plan Installatietekening Plan d`installation Pianta di installazione Plano de instalación Plano de instalação Σχέδιο εγκατάστασης Asennusohje Installasjonsplan Installationsplan G PW 6161 EL Materialnummer / Mat. no.: Änderungsstand / Version: 00 Datum Zeichnung / Drawing date: Datum Legende / Legend date:

2

3

4

5

6

7 Technical datasheet Washer-extractor: Heating: PW 6161 Electric (EL) Legend: Circled, bold-type abbreviations: Connection required Abbreviations surrounded by broken circle: Connection optional or required, depending on model G Optional extras: UM Miele plinth UG/UO 6016 (UG = Box plinth/uo = Open plinth) Height Model mm 237 Width UG (UO) mm 920 (900) Depth UG (UO) mm 939 (899) BS Concrete platform Concrete platform optional (Min. quality B15) Recommended height mm 237 Minimum height mm 100 Recommended width mm 920 Recommended depth mm 910 Ensure good anchorage! Machine connections: Electrical 1. Standard voltage (as supplied) V 3N AC connection Frequency Hz Rated load kw 17 Fuse rating A 3 25 Supply lead, min. cross section mm² Standard voltage (as supplied) V 3 AC Frequency Hz Rated load kw 17 Fuse rating A 3 50 Supply lead, min. cross section (M 32) mm² Standard voltage (as supplied) V 3 AC 440 Frequency Hz 60 Rated load kw 17 Fuse rating A 3 25 Supply lead, min. cross section mm² Plug and socket connection recommended to facilitate electrical safety tests. Socket must be accessible after installation. In the case of hard-wired connections, an all-pole mains switch with a minimum contact gap of 3 mm must be provided. The use of an earth leakage circuit breaker (ELCB) is strongly recommended. If necessary, equipotential bonding with good galvanic contact must be provided in accordance with all appropriate national and local regulations. Peak load management Connection cable, min. cross-section mm² Input leads should not be in direct contact with any source of heat. Input signal via potential-free (galvanically separated) contact. Installationsplan PW 6161 EL Stand: Seite 7

8 Cold water (Soft water) Min. flow pressure kpa 100 Max. pressure kpa 1000 Max. throughput (if hot water supply is not available) l/min 26 (36) On-site connection thread according to DIN Inch ¾" external thread Length of connection hose (supplied) mm 1500 Water requirements (average for 60 C programme) Standard connection [with hot water connection] l/h not yet available Additional requirements if hot water supply is not available. Hot water Max. temperature C 70 Min. flow pressure kpa 100 Max. pressure kpa 1000 Max. throughput l/min 10 On-site connection thread according to DIN Inch ¾" external thread Length of connection hose (supplied) mm 1500 Water requirements (average for 60 C programme) Standard connection [with hot water connection] l/h not yet available If no hot water supply, connect hose to cold water! Raw water Min. flow pressure kpa 100 Max. pressure kpa 1000 (Optional) Max. throughput l/min 32 On-site connection thread according to DIN Inch ¾" external thread Length of connection hose (supplied) mm 1500 Water requirements (average for 60 C programme) Standard connection [with hot water connection] l/h not yet available If connected to raw water supply, subtract cold water (soft) volume. If no raw water supply, connect hose to cold water! Drainage via dump valve Max. temperature C 95 Machine drain connection (d a s l) [DN 70] mm On-site drain connection (d i s l) [DN 70 sleeve] mm Max. transient throughput l/min 200 Vented drainage required. If ventilation is insufficient, fit Miele kit, Mat. no Drain manifolds serving several machines must be of sufficient cross-section. Foam vent (Optional) Machine vent A drainage system for foam escaping from the drain vent can be built using standard drain pipe sections. An 87 branch with an end cap should be provided for this purpose. Vent machine interior to prevent excessive rise in pressure. Fittings (supplied) Miele plinth UG/UO metal angled brackets (to secure machine to plinth) 4 screws DIN 571 (Ø length) mm rawl plugs (Ø length) mm Machine must be secured! Fixing materials for floating screed floor to be provided on site On concrete platform 2 screws DIN 571 (Ø length) mm rawl plugs (Ø length) mm Machine must be secured! Fixing materials for floating screed floor to be provided on site Installationsplan PW 6161 EL Stand: Seite 8

9 Without plinth 2 screws DIN 571 (Ø length) mm rawl plugs (Ø length) mm Machine must be secured! Fixing materials for floating screed floor to be provided on site Machine data Width mm 920 Depth mm 910 Height mm 1400 Knocked-down dimensions (W H) mm 1000 x 1500 Recommended gap to opposite wall mm 1500 Net weight kg 458 Dynamic floor load, max. N 5469 Static floor load, max. N 5003 Drum frequency, max. Hz 19.2 Average heat dissipation (dependent on ambient room temperature and programme selected) W not yet available Installation should only be carried out by authorised fitters in accordance with valid regulations! Observe installation instructions when installing machine! All rights reserved! Installationsplan PW 6161 EL Stand: Seite 9