A77 SNMPv3 SCADA INTERFACE INSTRUCTIONS

Transcription

1 A77 SNMPv3 SCADA INTERFACE OPTION 21X INSTRUCTIONS This manual is only valid for A77 Chargers equipped with the following: S2A-368S card with software version P368S0112 MIB file P389S-21X4-01-P368S0112 S2A-389S card with software version P389S-21X4-01-P368S0112 CPN: /18 ECN/DATE 106 BRADROCK DRIVE DES PLAINES, IL (847) FAX: (847) ISSUE DATE: ECN (4-18) INSTRUCTION DRAWING NUMBER: P25-LOPT21X-A77-368S-01 Page 1 of 8

2 IP Address: Subnet: Gateway: Traps: Disabled Trap Receiver IP: User #1 USM User: lamarche Hash Type: MD5 Auth Password: auth12345 Privacy Type: AES128 Privacy Password: priv12345 User #2 USM User: SnmpAdmin Hash Type: SHA1 Auth Password: DesPlaines Privacy Type: None Privacy Password: illinois User #3 USM User: root Hash Type: None Auth Password: authadmin Privacy Type: None Privacy Password: privadmin Default Settings Web Interface All settings are available through a web interface that may be accessed at; Default Username: admin Default Password: lamarche MIB File The La Marche MIB file for your charger can be downloaded from: Security LaMarche recognizes that not all customers desire to have the ability to remotely change settings. This feature is located in the Settings Menu. Within the Advanced Settings Menu is the Communications Menu. Under the Communications Menu is the Remote Disable selection. The only way to enable/disable this feature is through the front panel of the charger. When Remote Disable is set to YES the communications operate in read only mode. Please note that remote setting changes are always disabled whenever the settings menu is entered. Page 2 of 8

3 Page 3 of 8 Monitored Data Object ID Description Scale Factor Read/ Write Sends Trap COMMS_STATUS Charger Comms Alarm Status. Failure indicates a communications problem between the charger control board and SNMP Agent Board. Data read back is invalid. (FAIL=1) AC_ALARM_STATUS AC Fail Alarm Status. (FAIL=1) LOW_AC_ALARM_STATUS Low AC Alarm Status. (FAIL=1) LV_ALARM_STATUS Low Voltage Alarm Status. (OK=0,LOW VOLTAGE=1,LOW BATTERY VOLTAGE=2) HV_ALARM_STATUS High Voltage Alarm Status. (FAIL=1) HVSD_ALARM_STATUS High Voltage Shutdown Alarm Status. (FAIL=1) LC_ALARM_STATUS Low Current Alarm Status. (FAIL=1) GD_ENABLED_STATUS Ground Detection Enabled. (ENABLED=1) PG_ALARM_STATUS Positive Ground Alarm Status. (FAIL=1) NG_ALARM_STATUS Negative Ground Alarm Status. FAIL=1) SUM_ALARM_STATUS Summary Alarm Status. (FAIL=1) EOD_ALARM_STATUS End of Discharge Alarm Status. (FAIL=1) OL_ALARM_STATUS Overload Current Alarm Status. (FAIL=1) CF_ALARM_STATUS Charger Failure Alarm Status. (FAIL=1) OT_ALARM_STATUS Over Temperature Alarm Status. (FAIL=1) SCR_ALARM_STATUS SCR Failure Alarm Status. (FAIL=1) OT_PROBE_STATUS Over Temperature Probe Status. (FAIL=1) TC_PROBE_STATUS Temperature Compensation Probe Status. (FAIL=1) OPTIONAL_417S_GND_ENA Charger is equipped with optional 417s Ground None R No BLED Detection Option. (YES=1) OPTIONAL_417S_GND_DET Optional 417S Ground Detection Board has _FAILURE failed. (FAIL=1) OPTIONAL_411S_BOARD Charger is equipped with optional 411s ACV/ACA None R No Measurement Option. (YES=1) OPTIONAL_411S_FAILED Optional 411S ACV/ACA Measurement Board has failed. (FAIL=1) REMOTE_CHANGE_PROHIB When read as 1 remote changes are not allowed. IT This can occur because the charger is set this way or when a local operator is changing settings. THREE_PHASE_CHARGER Phase of charger. (1 PHASE=0, 3 PHASE=1) None R No BOT_ALARM_STATUS Battery Over Temperature Alarm Status. (FAIL=1) ACBO_ALARM_STATUS Open AC Breaker Alarm Status. (FAIL=1) DCBO_ALARM_STATUS Open DC Breaker Alarm Status. (FAIL=1) LE_ALARM_STATUS Low Electrolyte Alarm Status. (FAIL=1) LVBD_OPTION_ENABLE When read as 1 the charger is equipped with the None R No Low Voltage Battery Disconnect (LVBD) option. LVBD_ALARM_STATUS Low Voltage Battery Disconnect Alarm Status. (FAIL=1) CHARGER_MODE Charger Mode. (FLOAT=0, EQUALIZE=1) None RW Yes AC_IN_SUMMARY AC Alarm in Summary. (YES=1) LC_IN_SUMMARY Low Current Alarm in Summary. (YES=1) OL_IN_SUMMARY Overload Alarm in Summary. (YES=1) GD_IN_SUMMARY Ground Detection Alarms in Summary. (YES=1)

4 LATCH_ALARMS Latch Alarms. (YES=1) LATCH_EOD_ALARM Latch End of Discharge Alarm. (YES=1) LCD_BL_MODE LCD Backlight Automatically turns off after 2 minutes of inactivity. (YES=1) EVENT_LOG_ENABLE Event Logging Enable. (YES=1) BOT_IN_SUMMARY Battery Over Temperature Alarm in Summary. (YES=1) ACBO_IN_SUMMARY Open AC Breaker Alarm in Summary. (YES=1) DCBO_IN_SUMMARY Open DC Breaker Alarm in Summary. (YES=1) BOT_ALARM_DISABLE Battery Over Temperature Alarm Disabled. (DISABLED=1) ACBO_ALARM_DISABLE Open AC Breaker Alarm Disabled. (DISABLED=1) DCBO_ALARM_DISABLE Open DC Breaker Alarm Disabled. (DISABLED=1) H1PCT_IN_SUMMARY Hydrogen Gas at 1 Percent Alarm in Summary. (YES=1) LE_ALARM_DISABLE Low Electrolyte Level Alarm Disabled. (DISABLED=1) LVBD_IN_SUMMARY Low Voltage Battery Disconnect Alarm in Summary. (YES=1) LVBD_ALARM_DISABLE Low Voltage Battery Disconnect Alarm disable. (DISABLED=1) BOARD_NUMBER Control Board Number. (368=368S) None R No SOFTWARE_VERSION Software Version. None R No DCV DC Voltage. Volts. 0.1 R No DCA DC Current. Volts. 0.1 R No EQ_TIMER_HHMM Equalize Cycle Time Remaining, HHMM. Note the None R No first two digits are the hours. The last two digits are the minutes. AUTOEQ_TIMER_DAYS Days to next Auto Equalize. Days. None R No AUTOEQ_TIMER_HHMM Hours, Minutes to next Auto Equalize. Note the None R No first two digits are the hours. The last two digits are the minutes. LC_ALARM_LOW_LIMIT Low DC Current Alarm Low Limit. Note setting 0.1 R No the Low DC Current Alarm below this will result in disabling the Low DC Current Alarm. Amps. OT_PROBE_C Over Temperature Probe Reading. Check None R No OT_PROBE_STATUS to determine if reading is valid. Degrees C =Probe Open 10002=Probe Shorted 10003=Probe Disabled 10004=Probe N/A TC_PROBE_C Temperature Compensation Probe Reading. None R No Check TC_PROBE_STATUS to determine if reading is valid. Degrees C =Probe Open 10002=Probe Shorted 10003=Probe Disabled 10004=Probe N/A OT_ALARM_C Over Temperature Alarm Threshold. Degrees C. None R No MAX_ALARM_VOLTS The maximum value voltage alarms may be set 0.1 R No to. Volts. MAX_ALARM_AMPS The maximum value current alarms may be set to. Volts. 0.1 R No Page 4 of 8

5 MAX_FL_VOLTS The maximum allowable Float Voltage. Volts. 0.1 R No MIN_FL_VOLTS The minimum allowable Float Voltage. Volts. 0.1 R No MAX_EQ_VOLTS The maximum allowable Equalize Voltage. Volts. 0.1 R No MIN_EQ_VOLTS The minimum allowable Equalize Voltage. Volts. 0.1 R No MAX_CL_AMPS The maximum allowable Current Limit. Amps. 0.1 R No MIN_CL_AMPS The minimum allowable Current Limit. Amps. 0.1 R No LOG_PCT_USED The percent of the event log file used R No MAX_TEMP_COMP_RATE Maximum Temperature Compensation Rate R No Volts/Cell/C. ACV AC Voltage. Volts. 0.1 R No AC_FREQ AC Frequency. Hz. 0.1 R No BATTERY_TYPE Battery Type. None R No Lead Acid = 0 NiCad = 1 BATTERY_CELLS Battery Cells. None R No ACVP1 AC Phase 1 Voltage. Will read 0 on 1 Phase 0.1 R No ACVP2 AC Phase 2 Voltage. Will read 0 on 1 Phase 0.1 R No ACVP3 AC Phase 3 Voltage. Will read 0 on 1 Phase 0.1 R No ACAP1 AC Phase 1 Amps. Will read 0 on 1 Phase 0.1 R No ACAP2 AC Phase 2 Amps. Will read 0 on 1 Phase 0.1 R No ACAP3 AC Phase 3 Amps. Will read 0 on 1 Phase 0.1 R No POS_GND_MA Milliamps between Positive and Ground. 0.1 R No if option is available and OPTIONAL_417S_GND_DET_FAILURE to determine if value NEG_GND_MA Milliamps between Negative and Ground. if option is available and OPTIONAL_417S_GND_DET_FAILURE to determine if value 0.1 R No Page 5 of 8

6 GND_NEG_VOLTS Voltage between Ground and Negative. Volts. 0.1 R No if option is available and OPTIONAL_417S_GND_DET_FAILURE to determine if value POS_GND_VOLTS Voltage between Positive and Ground. Volts. 0.1 R No if option is available and OPTIONAL_417S_GND_DET_FAILURE to determine if value OT_ALARM_TYPE Over Temperature Alarm Type. OK=0, FAIL=1, DERATE=2, SHUTDOWN=3 H2GAS_READING Hydrogen Gas Sensor Reading. 0 Percent=0, 1 Percent=1, 2 Percent=2, Sensor Failure=3, Option Not Available=4 EQT_MODE Equalize Timer Mode. Valid Range: 0 to 4. EQT_HOURS Equalize Timer Setting. Hours. Valid Range: 0 to 144. LV_ALARM_VOLTS Low Voltage Alarm Threshold. Volts. Valid 0.1 RW No Range: 0 to MAX_ALARM_VOLTS HV_ALARM_VOLTS High Voltage Alarm Threshold. Volts. Valid 0.1 RW No Range: 0 to MAX_ALARM_VOLTS HVSD_ALARM_VOLTS High Voltage Shutdown Alarm Threshold. Volts. 0.1 RW No Valid Range: 0 to MAX_ALARM_VOLTS LC_ALARM_AMPS Low DC Current Alarm Threshold. Amps. Valid 0.1 RW No Range: 0 to MAX_ALARM_AMPS EOD_ALARM_VOLTS End of Discharge Alarm Threshold. Volts. Valid 0.1 RW No Range: 0 to MAX_ALARM_VOLTS FL_VOLTS Float Voltage Setting. Volts. Valid Range: 0.1 RW No MIN_FLOAT_VOLTS to MAX_FLOAT_VOLTS EQ_VOLTS Equalize Voltage Setting. Volts. 0.1 RW No Valid Range: MIN_EQ_VOLTS to MAX_EQ_VOLTS CL_AMPS Current Limit Setting. Amps. Valid Range: 0.1 RW No MIN_CL_AMPS to MAX_CL_AMPS TEMP_COMP_RATE The rate of temperature compensation in use RW No Note: 0=Temperature Compensation OFF Valid Range (Lead Acid): 0,1,2,3,4,5 Valid Range (NiCad): 0,1,2,3 LOG_INTERVAL Logging Interval. Minutes. Valid Range: 1 to 60 AC_ALARM_DELAY AC Alarm Delay. Seconds. Valid Range: 1 to 300 LV_ALARM_DELAY Low Voltage Alarm Delay. Seconds. Valid Range: 1 to 300 EOD_ALARM_DELAY End of Discharge Alarm Delay. Seconds. Valid Range: 1 to 300 EQTM4_ALARM_DELAY Equalize Timer Mode 4 Delay. Seconds. Valid Range: 1 to 300 HV_ALARM_DELAY High Voltage Alarm Delay. Seconds. Valid Range: 1 to 300 HVSD_ALARM_DELAY High Voltage Shutdown Alarm Delay. Seconds. Valid Range: 1 to 300 LC_ALARM_DELAY Low Current Alarm Delay. Seconds. Valid Range: 1 to 300 LV_ALARM_RESET Low Voltage Alarm Reset Threshold. Percent. Valid Range: 0 to 20 Page 6 of 8

7 EOD_ALARM_RESET End of Discharge Alarm Reset Threshold. Volts. Valid Range: 0 to MAX_ALARM_VOLTS RTC_MONTH Real Time Clock (RTC) Month. Valid Range: 1 to 12 RTC_DAY Real Time Clock (RTC) Day of Month. Valid Range: 1 to 31 RTC_YEAR Real Time Clock (RTC) Year. Valid Range: 2000 to 2200 RTC_HOUR Real Time Clock (RTC) Hours. Valid Range: 0 to 23 RTC_MIN Real Time Clock (RTC) Minutes. Valid Range: 0 to 59 RTC_SEC Real Time Clock (RTC) Seconds. Valid Range: 0 to 59 GD_ALARM_DELAY Ground Detection Alarm Delay. Seconds. Valid Range: 0 to 300 GND_DET_MILLIAMPS Ground Detection Alarm Threshold. 0.1 RW No if option is available. BOT_ALARM_C Battery Over Temperature Alarm. Degrees C. Valid Range: 25 to 100 ACBO_OPTION_ENABLE Charger is equipped with optional Open AC None R No Breaker Alarm Option. DCBO_OPTION_ENABLE Charger is equipped with optional Open DC None R No Breaker Alarm Option. LE_OPTION_ENABLE Charger is equipped with optional Low Electrolyte None R No Level Alarm Option. AC_FAIL_ALARM_VOLTS AC Fail Alarm Voltage Threshold. Note: Settings 0.1 RW No below MIN_AC_FAIL will set the alarm threshold to 50% of the Chargers AC Voltage Rating. MIN_AC_FAIL_VOLTAGE Minimum AC Fail Alarm Voltage Threshold. 0.1 R No Settings written below this value will set the threshold to 50% of the Chargers AC Voltage Rating ELAPSED_AUTO_BATT_TES DAYS TO NEXT AUTOMATIC BATTERY None R No T_TIME_DAYS ELAPSED_AUTO_BATT_TES HOURS & MINUTES TO NEXT AUTOMATIC None R No T_TIME_HOURS_MINS BATTERY CONTINUITY TEST. NOTE: FIRST TWO DIGITS ARE HOURS. LAST TWO ARE MINUTES BATT_CONT_TEST_STATUS Battery Continuity Test Status 0=IDLE,1=TEST IN PROCESS,2=TEST FINISHED BATT_CONT_TEST_RESULT Battery Continuity Test Result 0=NOT TESTED 1=TESTING BATTERY 2=TEST PASSED 3=CHECK BATTERY 4=TEST FAILED 5=TEST NOT STARTED, CHARGER IN EQUALIZE 6=TEST NOT STARTED, CHARGER LOAD > 50% 7=TEST NOT STARTED, ALARM CONDITION PRESENT AUTO_BATT_CONT_TEST_E Automatic Battery Test Mode. NABLE Page 7 of 8

8 BATT_CONT_FAIL_ALARM_ Include Battery Continuity Test Fail Alarm in SUMMARY Summary. CHECK_BATT_ALARM_SUM Include Battery Continuity Test Check Battery MARY Alarm in Summary. START_BATT_CONT_TEST Start Battery Continuity Test. AUTO_BATT_CONT_TEST_ Automatic Battery Continuity Test Interval DAYS_INTERVAL Valid Settings: 1,7,14,21,30,60 REMOTE_BATTERY_VOLTA Optional Battery Voltage Sensing in Enabled None R No GE_ENABLE 1=ENABLED REMOTE_BATTERY_VOLTA GE Optional Battery Voltage Reading. Monitor REMOTE_BATTERY_VOLATGE_ENABLE setting to see if voltage is available. 0.1 R No Page 8 of 8