Magnetically Operated Touch Panel Hints on Operating CAT 100 / BINOS 100 F and CAT 200 / MLT 2 Gas Analyzers

Transcription

1 Instruction Manual Magnetically Operated Touch Panel Hints on Operating CAT 100 / BINOS 100 F and CAT 200 / MLT 2 Gas Analyzers

2 ESSENTIAL INSTRUCTIONS READ THIS PAGE BEFORE PROCEEDING! Rosemount Analytical designs, manufactures and tests its products to meet many national and international standards. Because these instruments are sophisticated technical products, you MUST properly install, use, and maintain them to ensure they continue to operate within their normal specifications. The following instructions MUST be adhered to and integrated into your safety program when installing, using and maintaining Fisher-Rosemount products. Failure to follow the proper instructions may cause any one of the following situations to occur: Loss of life; personal injury; property damage; damage to this instrument; and warranty invalidation. Fisher-Rosemount MFG GmbH & Co. OHG must not be liable for any errors in this documentation. As well any liability for direct and indirect damages which occur in relation to the delivery or usage of this documentation is refused as far as accepted by law.. Read all instructions prior to installing, operating, and servicing the product. If you do not understand any of the instructions, contact your Fisher- Rosemount representative for clarification. Follow all warnings, cautions, and instructions marked on and supplied with the product. Inform and educate your personnel in the proper installation, operation, and maintenance of the product. Install your equipment as specified in the Installation Instructions of the appropriate Instruction Manual and per applicable local and national codes. Connect all products to the proper electrical and pressure sources. To ensure proper performance, use qualified personnel to install, operate, update, program, and maintain the product. When replacement parts are required, ensure that qualified people use replacement parts specified by Fisher-Rosemount. Unauthorized parts and procedures can affect the product s performance, place the safe operation of your process at risk, and VOID YOUR WARRANTY. Look-alike substitutions may result in fire, electrical hazards, or improper operation. Ensure that all equipment doors are closed and protective covers are in place, except when maintenance is being performed by qualified persons, to prevent electrical shock and personal injury. The information contained in this document is subject to change without notice. 1. edition Emerson Process Management Fisher-Rosemount MFG GmbH & Co. OHG Industriestrasse 1 D Hasselroth Germany T +49 (6055) F +49 (6055)

3 Instruction Manual Magnetically Operated Touch Panel SECTION 1 Introduction 1-1 Overview Analyzers intended either to be used in hazardous area or for outdoor usage are provided with a magnetically operated touch panel. This special version ensures ingress protection (IP) and resistance against mechanical shocks. On account of its design it requires some special measures to operate the corresponding analyzer in a safe manner, so read the following instructions carefully! 1-2 Magnetic Touch Panel Elements Whereas standard front panels are using keys for operating the analyzer the magnetically operated touch panel uses contactless technology instead. This results in a slightly different design: Each standard panel key is replaced by a reed relay located behind the front panel design foil. (CAT 200, MLT 2 only: The sequence of the 4 keys at the right side has changed due to ergonomic reasons.) Fig. 1: CAT 100 / BINOS 100 F version Fig. 2: CAT 200 / MLT 2 version 1-3 Accessories To operate the magnetically operated touch panel a special tool (actuator) is required. The following picture shows this tool as it should be provided together with your analyzer. If it is missing please contact your local sales office. Fig. 3: Magnetic actuator Fig. 4: Magnetic actuator, view at magnets Fisher-Rosemount MFG GmbH & Co. OHG A Division of Emerson Process Management 3

4 Magnetically Operated Touch Panel Instruction Manual SECTION 2 Operating the Touch Panel 2-1 Operating the Touch Panel The touch panel is operated by activating the reed relays using the actuator. This is done by holding that actuator s end in front of the key that is equipped with 2 small magnets. As the reed relays are installed alternating vertical and horizontal to prevent accidentally activation of an adjacent key, the actuator has to be aligned the same way. The design foil shows for each key how the actuator has to be aligned using the symbols and : Fig. 5: Symbols showing actuator alignment Fig. 6: Horizontally aligned, activating F4 Fig. 7: Vertically aligned, activating F5 CAT 100 only: A green light ( switch ctrl ) is turned on when the actuator has the correct position and activates the reed relay. It is placed right above the input control keys. Switch control Fig. 8: CAT 100 switch control 4 Fisher-Rosemount MFG GmbH & Co. OHG A Division ofemerson Process Management

5 Instruction Manual Magnetically Operated Touch Panel 2-2 Storing the actuator tool 2-2 Storing the actuator tool The tool is provided with a chain and a special fixture to be installed at one of the analyzer s mounting screws (s. fig. 9). It is recommended to place the actuator tool on the fixture as shown to avoid unintended interference while not in use. Fig. 9: Actuator stored when not in use Fisher-Rosemount MFG GmbH & Co. OHG A Division of Emerson Process Management 5

6 Magnetically Operated Touch Panel Instruction Manual SECTION 3 Adjusting the CAT Series Touch Panel To ensure safe and faultless operation of the touch panel it is required to have the control elements (reed relays) installed within a defined distance from the inner side of the security glass. If it is necessary to remove the CAT 100 or CAT 200 dome for maintenance and/or inspection purposes and to loosen the internal analyzer, the following measures must be followed: 3-1 Sliding the Analyzer into Position Set the analyzer module onto the fixture. Position the dome and fix it turning it clockwise. The inner side of the front glass now should have contact to the analyzers key pad bar and push the analyzer into the CAT housing. The front of the key pad bar should now have a distance from the inner side of the dome s front glass of between 0 and max. 2-3 mm (fig. 10). If the distance is bigger, it has to be corrected by repeating the procedure. Next remove the CAT dome once more. 3-2 Fixing the Analyzer Fix the analyzer on the fixture using the screws located at the analyzers left and right side. 3-3 Completing the Adjustment Postion the CAT dome and fix it. Make sure the distance is still correct. Front glass Analyzer Dome Key pad bar max. 2-3 mm Fig. 10: Distance between glass and key pad bar 6 Fisher-Rosemount MFG GmbH & Co. OHG A Division ofemerson Process Management

7 Instruction Manual Magnetically Operated Touch Panel Fisher-Rosemount MFG GmbH & Co. OHG A Division of Emerson Process Management 7

8 Magnetically Operated Touch Panel Instruction Manual Emerson Process Management Rosemount Analytical Inc. Process Analytic Division 1201 N. Main St. Orrville, OH T +1 (330) F +1 (330) E gas.csc@emersonprocess.com Fisher-Rosemount MFG GmbH & Co. OHG Industriestrasse Hasselroth Germany T +49 (6055) F +49 (6055) ASIA - PACIFIC Fisher-Rosemount Singapore Private Ltd. 1 Pandan Crescent Singapore Republic of Singapore T F EUROPE, MIDDLE EAST, AFRICA Fisher-Rosemount Ltd. Heath Place Bognor Regis West Sussex PO22 9SH England T F LATIN AMERICA Fisher - Rosemount Av. das Americas 3333 sala 1004 Rio de Janeiro, RJ Brazil T Fisher-Rosemount MFG GmbH & Co. OHG 2002