UL Electrical Equipment for Measurement, Control, and Laboratory Use; Part 1: General Requirements, Second Edition
|
|
- Evangeline Phillips
- 5 years ago
- Views:
Transcription
1 File E Project 07CA39477 March 5, 2008 REPORT on PROCESS CONTROL EQUIPMENT FOR USE IN HAZARDOUS LOCATIONS Litre Meter Ltd. Buckinghamshire, England Copyright 2008 Underwriters Laboratories Inc. Underwriters Laboratories Inc. authorizes the above named company to reproduce this Report provided it is in its entirety.
2 File E Vol. 1 Sec. 1 Page 1 Issued: DESCRIPTION PRODUCT COVERED: USL Associated Apparatus Flow Meter for use in Class I, Division 1, Groups B, C, and D Hazardous Locations. Model FPODEXD-XJLGCHN4X provides intrinsically safe circuits for use in Class I, Division 1, Groups B, C, and D Hazardous Locations when installed in accordance with manufacturer s control drawing no. IS GENERAL: Model FPODEXD-XJLGCHN4X is a permanently mounted flow meter consisting of an explosion-proof enclosure containing a PCB with LCD mounted on an internal chassis, an IS barrier, and a communication interface connected to sensor model ULCOVERXA, followed by two single digit numbers. ENGINEERING CONSIDERATIONS (NOT FOR FIELD REPRESENTATIVE S USE): USL indicates investigation to the following United States Standards: UL Electrical Equipment for Measurement, Control, and Laboratory Use; Part 1: General Requirements, Second Edition UL 1203 Explosion-proof and Dust Ignition-proof Equipment for Use in Class I, II and III Hazardous (Classified) Locations, Fourth Edition UL 913, Intrinsically Safe Apparatus and Associated Apparatus for Use in Class I, II, and III Hazardous (Classified) Locations, Fifth Edition RATINGS: Power Input: 24 V dc, 100 ma max, +/-10%. Signal Input (Reed Switch) 24 V dc max, 10 ma max. Control Output: 24 V dc max, 100 ma. Signal (Communications Output): 32 V dc max, 4-20 ma HART or Fieldbus Output: Terminals 1 and 2 (from IS barrier): Voc = 10.5 V Isc = 14 ma Ca = 2.4 uf La = 165 mh Temperature Rating: -20ºC < Ta < +60ºC Temperature Code: T5MARKINGS: The device is provided with the markings as shown in ILL. 1 on a riveted, aluminum or stainless steel label.
3 File E Vol. 1 Sec. 1 Page 2 Issued: CONTROL DRAWING: A copy of the control drawing no. IS 6095, shown in ILL. 2, is provided with each device. INSTALLATION INSTRUCTIONS: Installation Instructions are provided with each device and shall include the following: 1. The supply voltage shall not exceed 36 V dc, and The supply must be isolated from mains voltage by double/reinforced insulation 2. Intended use of the equipment, technical specifications including the supply voltage and power or current rating and a description of all input and output connections, instructions for use, name and address of manufacturer or supplier from whom technical assistance may be obtained 3. A statement of the range of environmental conditions for which the equipment is designed 4. Assembly, location and mounting requirements, instruction for protective earthing, field wiring size, type, tightening torque and recommended strip length 5. That a switch or circuit-breaker shall be included in the building installation, and a recommendation that the switch or circuit breaker used as the disconnect be located near the equipment 6. Instructions for interconnection to accessories and other equipment 7. If the display (explosion-proof enclosure) needs to be mounted away from the meter care should be taken when routing the armored cable. The cable should be fixed (clamped) within 20 in. (500 mm) of the glands (both meter and enclosure) to support and maintain the integrity of the seal. After installation these seals should be visually checked for damage. The cable length will not exceed 33 feet (10 m). CONSTRUCTION DETAILS: General The device is constructed in accordance with the following figures, illustrations and descriptive pages. Dimensions are approximate unless specifically indicated otherwise. Spacings Where affecting intrinsic safety, spacings have been evaluated and found to be in accordance with Table 8.1 in UL 913, Fifth Edition.
4 File E Vol. 1 Sec. 1 Page 3 Issued: Clearance And Creepage Distances - Requirements for clearance and creepage distances were based on Pollution Degree 2. Clearances were evaluated and determined to comply with the requirements outlined in Table 5 of UL Creepage distances were evaluated and determined to comply with the requirements outlined in Table 7 or UL Internal Wiring Unless otherwise indicated, all internal wiring is R/C (AVLV2) rated 300 V, 100ºC minimum, and 24 AWG minimum with minimum insulation thickness of 0.25 mm. Printed Wiring board - Any R/C (ZPMV2) with flame rating of V-0, V-1, or V-2 and an operating temperature of 105 C, meets UL 746 direct support requirements. DOCUMENTATION: FIG. No. The device is constructed in accordance with the following drawings: ILL. No. Description Drawing No. Revision/Date 1 FPODEXD-XJLGCHN4X, External Internal PCBs Rear View, PCBs IS Barrier, Front View Metal Partition Label LM-UL-TAG 1 2 Control Drawing IS OVERALL BOM FPODEXD-XJLGCHN4X BOM FLIN Board Schematic PB IS Screen Illustration - 1
5 File E Vol. 1 Sec. 1 Page 4 Issued: Revised: MODEL FPODEXD-XJLGCHN4X (OVERALL ASSEMBLY) - FIG. 1 General Shown is the assembly of Model FPODEXD-XJLGCHN4X. Please note that the labels shown in the picture are not the final versions; see ILL. 1 for the final version. The complete assembly consists of an explosion-proof enclosure containing a 2-line LCD, temperature transmitter, F-Lin PCB, internal chassis, and IS barrier; along with a flow meter sensor connected via a cable, with a maximum length of 10 m. 1. Enclosure Listed (FTRV) enclosure manufactured by Adalet-PLM Fetzer Co., Cat. No. XJLGCHN4X. Overall dimensions of 6 5/32in.H by 7in.W by 7 in.d. The enclosure is provided with a 4 in. diameter window and two 3/4 in. NPT conduit entries. The enclosure is suitable for an ambient temperature of -20ºC to +60ºC. All unused conduit entries shall be filled with a UL Listed (EBNV) Plugs suitable for at least the same class and groups as indicated under the product covered and with at least five (5) full threads engaged. Threaded Joint Metal-to-metal threaded joint between the enclosure, Item 1, and Cable Sealing Fitting, Item 8, engages not less than five full NPT threads upon assembly Line LCD manufactured by Ampire, Cat. No. AC-162BYILY. Dimensions 3 1/8 in. by 1 3/8 in.. 3. Foundation Fieldbus Puck manufactured by Wika, Cat. No. TE XX where XX = NI or IS Dimensions 1 3/4 in. diameter by 3/4 in. deep. 4. F-LIN PCB manufactured by Litre Meter, Cat. No Dimensions 3 1/8 in. by 2 1/2 in. 5. Internal Chassis 6. IS Barrier UL Listed (QUZW), manufactured by Measurement Technology Ltd., Part No See FIG Partition Grounded, metal partition, separating IS from non-is wiring. See ILL. 5 and FIG. 5 for views. 8. Cable Sealing Fitting UL Listed (CYMX), manufactured by Hawke, Cat. No. 711 size A. Marked for an ambient range of 50 C to +60 C. For use only with MC cable employing continuous corrugated aluminum armor with HL surface marking and either ST574 or Hawkseal (Bicaseal) Activator sealing compounds. Cable OD range over jacket is Fittings must be installed per the manufacturer s instructions. 9. Cable UL Listed (PJPP), manufactured by Okonite, Type MC-HL cable with continuous corrugated aluminum armor. Cable has an outer diameter of approximately 0.70in. Cable contains three (one cut back) Recognized (AVLV2) 14 gauge, Type XHHW-2 copper insulated conductors. Rated 600 V. 10. Flow Meter Sensor Housing may vary, only contains reed switch. Marked with the following nomenclature: ULCOVERXAYY, where YY may be any two digit number, varying with the housing.
Certificate of Compliance
Certificate of Compliance Certificate: 1055868 (LR 44092) Master Contract: 152450 Issued to: Micro Motion Incorporated 7070 Winchester Cir Boulder, CO 80301 USA Attention: Ray C. Stengl The products listed
More informationFile E Project 05ME Issued: November 1, 2005 Revised: February 27, 2009 REPORT
File E133400 Project 05ME09466 Issued: November 1, 2005 Revised: February, 2009 REPORT On COMPONENT POWER SUPPLIES, INFORMATION TECHNOLOGY EQUIPMENT INCLUDING ELECTRICAL BUSINESS EQUIPMENT TDK-Lambda Americas
More informationIECEx Certificate of Conformity
INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com issue No.:2 Status: Current Certificate history:
More informationCertificate of Compliance
Certificate of Compliance Certificate: 1655492 (219995) Issued to: R.C. Systems Co., Inc. 8621 Hwy 6 Hitchcock, Texas 77563 USA Attention: Roger Carter The products listed below are eligible to bear the
More informationINSTRUCTION MANUAL. D1xB2XH1 Xenon Beacon For use in Hazardous Locations. 2) Rating & Marking Information
INSTRUCTION MANUAL D1xB2XH1 Xenon Beacon For use in Hazardous Locations 2) Rating & Marking Information 2.1 Public Mode Fire Alarm Ratings The D1xB2XH1 is certified for use as public mode visual alarm
More informationINSTRUCTION MANUAL. D1xB2XH2 Xenon Beacon For use in Hazardous Locations. 2) Rating & Marking Information
INSTRUCTION MANUAL D1xB2XH2 Xenon Beacon For use in Hazardous Locations 2) Rating & Marking Information 2.1 Public Mode Fire Alarm Ratings The D1xB2XH2 is certified for use as public mode visual alarm
More informationTank Gauging System Special Safety Instruction
Tank Gauging System www.rosemount-tg.com Rosemount TankRadar REX Table of Contents Contents SPECIAL SAFETY INSTRUCTION........................ 1-1 1. GENERAL REQUIREMENTS....................... 1-2 1.1
More informationAM54. Armored Variable Area Flowmeter Series AM54331/32 Series AM54371/72/73/74 Series AM54431/32 Series AM54471/72/73/74
AM54 Instruction Bulletin North American Installation Addendum Document Number PN25016 Armored Variable Area Flowmeter Series AM54331/32 Series AM54371/72/73/74 Series AM54431/32 Series AM54471/72/73/74
More informationccsaus certificate: for GSI 127 Meggitt SA Route de Moncor 4 PO Box 1616 CH Fribourg Switzerland Title Page
Title Page ccsaus certificate: EN 70001999 for EX Meggitt SA Route de Moncor 4 PO Box 1616 CH - 1701 Fribourg Switzerland ccsaus certificate 70001999 www.meggittsensingsystems.com www.vibro-meter.com THIS
More informationCertificate of Compliance
Certificate of Compliance Certificate: 1563164 Issued to: Metal Samples Company, A Div. of Alabama Specialty Products, Inc. 152 Metal Samples Rd PO Box 8 Munford, Alabama 36268 USA Attention: Bala Palanisamy
More informationSLATE. Sub-Base Module INSTALLATION INSTRUCTIONS R8001S9001
SLATE Sub-Base Module R8001S9001 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform. The platform
More informationIECEx Certificate of Conformity
INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com Certificate No.: IECEx UL 08.0012X issue No.:5
More informationFile E Project 97SC January 21, 1998 REPORT
File E135803 Project 97SC15289 January 21, 1998 REPORT ON COMPONENT - POWER SUPPLIES, INFORMATION TECHNOLOGY EQUIPMENT, INCLUDING ELECTRICAL BUSINESS EQUIPMENT Condor DC Power Supplies Inc. Oxnord, CA
More informationstandards: standards:
INSTRUCTION MANUAL D2xB1LD2 LED Beacons For use in Hazardous Locations 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT DO NOT OPEN WHEN ENERGISED POTENTIAL ELECTROSTATIC CHARGING HAZARD
More informationFile S789 Project 04ME December 20, 2005 REPORT CONTROL UNIT (UOJZ) * * * * * * * * * * * * * * * * * * * * *
File S789 Project 04ME15779 December 20, 2005 REPORT on CONTROL UNIT (UOJZ) * * * * * * * * * * * * * * * * * * * * * Complementary Product Categories CENTRAL STATION ALARM UNITS (AMCX, AMCX7) POLICE STATION
More informationField Certification Certificate of Compliance
2 Field Certification Certificate of Compliance Certificate: 2415870 Master Contract: 225996 Project: 2415870 Issued to: SpectraSensors, Inc. 11027 Arrow Route Rancho Cucamonga, CA 91730 USA Attention:
More informationIECEx Certificate of Conformity
IECEx Certificate of Conformity INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com Certificate IECEx
More informationINSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR PIPE THREAD IMMERSION HEATERS USED IN HAZARDOUS LOCATIONS
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR PIPE THREAD IMMERSION HEATERS USED IN HAZARDOUS LOCATIONS I. GENERAL Heatrex Explosion-proof Pipe Thread Mounted Immersion Heaters are CSA approved
More informationIECEx Certificate. INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres
INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com Certificate No.: Certificate history: Status:
More informationCertificate of Compliance
Certificate of Compliance Certificate: 70033893 (166720) Issued to: WIKA Alexander Wiegand SE & Co. KG Alexander-Wiegand-Str 30 Klingenberg, 63911 GERMANY Attention: Uwe Schmidt The products listed below
More informationD SYSTEM CONTROL DWG. APPROVED BY. OrCAD 6 ROSEMOUNT 2410
FIELDBUS INTRINSICALLY SAFE CONCEPT (FISCO) APPROVAL FISCO allows interconnection of intrinsically safe apparatus to associated apparatus not specially examined in such combination. The criteria for interconnection
More informationModel 144H. Product Data Sheet , Rev DB February Content
Rosemount 144 PC-Programmable Temperature Transmitter Provides an installation-ready solution for temperature monitoring applications using Complete Point Solutions (CPS) Increases measurement accuracy
More informationQuick Start Guide For the
A Leader in Level Measurement Quick Start Guide For the Universal IV Lite and Universal IV Pro Model Transmitters 2-Wire RF Admittance / Capacitance Level Measurement System with HART Protocol For Assistance
More informationSLATE. Base Module INSTALLATION INSTRUCTIONS R8001A1001
SLATE Base Module R8001A1001 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform. The platform can
More informationHazardous Area Zirconia Oxygen Systems
Operating Instructions IM/EXGP-INT_7 Hazardous Area Zirconia Oxygen Systems Interface Electronics Unit ABB The Company We are an established world force in the design and manufacture of instrumentation
More informationINSTRUCTION & SERVICE MANUAL D1xS1 & D1xS2 ALARM HORNS For Use In Hazardous Locations - Gas
INSTRUCTION & SERVICE MANUAL D1xS1 & D1xS2 ALARM HORNS For Use In Hazardous Locations - Gas UL 1203 CSA C22.2 NO. 30-M1986 The D1xS1 and D1xS2 Alarm Horns also comply with the following standards for signaling
More informationUser s Manual YTA610 and YTA710 NEPSI Certification
User s Manual YTA60 and YTA70 NEPSI Certification [Option code: /NS, /NS5 and /NF] st Edition . INTRODUCTION Thank you for purchasing the YTA60 and YTA70 Temperature transmitters. This manual contains
More informationJ-PRO TM Cable Support System
Frequently Asked Questions Cable Support System What references define how and where J-hooks are used? J-hooks are a horizontal pathway promoted in the BICSI TDM manual as a means to route small to medium
More informationRosemount 752 Fieldbus Remote Indicator
Product Data Sheet Rosemount 752 Rosemount 752 Fieldbus Remote Indicator ROSEMOUNT 752 DELIVERS: Two-wire segment powered device Displays up to 8 values Link Master Capability Optional PID, Characterizer,
More informationINSTRUCTION MANUAL. D2xB1XH1 & D2xB1XH2 Xenon Beacons For use in Hazardous Locations
INSTRUCTION MANUAL D2xB1XH1 & D2xB1XH2 Xenon Beacons For use in Hazardous Locations synchronization requirements of UL1971 & UL1638 / CAN/ULCS526. 2.2 NEC & CEC Class / Division Ratings for US / Canada
More informationFLAME ITEM PART NO CLIENT REF. NO. DESCRIPTION DESIGNATION MANUFACTURER CLASS UL FILE NO.
BOM FOR UL CERTIFICATE NUMBER Model Name: CLASSIC TOWER LIGHT Documents Number 122-EI04 This is to certify that the above product was supplied to SUZO Internation (NL) BV Revision A2 are made of the followings,
More informationOilSET Installation and Operating Instructions. Oil Separator Alarm Device with SET/DM3AL sensor
Labkotec UK Ltd Adminicle House 1 Lumb Lane Audenshaw Manchester M34 5WH GREAT BRITAIN Tel: 0844 3350 477 Fax: 0161 4281 179 E-mail: info@labkotec.co.uk 10.8.2012 Internet: www.labkotec.co.uk 1/13 OilSET-1000
More informationCertificate of Compliance
FF0 001 Certificate of Compliance Certificate: 70116284 (LR 064969_0_00) Issued to: Mine Safety Appliances Company North American Division 1000 Cranberry Woods Dr Cranberry Township, Pennsylvania 16066-5296
More information7800 SERIES 22-Terminal Universal Subbase
7800 SERIES 22-Terminal Universal Subbase FEATURES PRODUCT DATA Q7800B003/2003/U Metal Wall-mount subbase Q7800A005/2005/U Plastic Wall-mount subbase Quick-mount wiring subbase for all 7800 SERIES Relay
More informationAnnubar Flowmeter Series
Reference Manual Appendix B Approvals Annubar Flowmeter Series Hazardous Locations Installations.................. page B-1 Rosemount 3051SFA Product Certifications.......... page B-1 Rosemount 3095MFA
More informationCertificate of Compliance
Certificate of Compliance Certificate: 2557738 Master Contract: 256526 Issued to: Bartec Varnost d.o.o Cesta 9 avgusta 59 Zagorje ob Savi, 1410 Slovenia Attention: Janez Gajski The products listed below
More informationUL Topic III. Converting European EEx Certificates. Into. North American Division Certificates
Note: While this material was originally prepared for presentation in February 1999, it has been updated to reflect the evolving technical requirements now applicable as of April 2003. UL Topic III Converting
More informationIECEx TEST REPORT IEC Explosive atmospheres Part 0: Equipment General requirements
ExTR Reference Number...: ExTR Free Reference Number...: 223531 Compiled by + signature (ExTL)...: Reviewed by + signature (ExTL)...: NO/NEM/ExTR12.0018/00 Stig André Norheim Arne Hortman Date of issue...:
More informationCertificate of Compliance
FF0 001 Certificate of Compliance Certificate: 70116279 (LR 025993_0_000) Issued to: General Monitors, Incorporated 26776 Simpatica Circle Lake Forest, California 92630 USA Attention: Larry Vlagea The
More informationModel 144H. Product Data Sheet , Rev DB February Content
Rosemount 144 PC-Programmable Temperature Transmitter Provides an installation-ready solution for temperature monitoring applications using Complete Point Solutions (CPS) Increases measurement accuracy
More informationNFPA 2001: Standard for Clean Agent Fire Extinguishing Systems NFPA 70: National Electrical Code (NEC) NFPA 72: National Fire Alarm Code
Part 1 - GENERAL 1.1 DESCRIPTION OF WORK A. Design and installation of an engineered Kidde ECS Advanced Delivery Systems (ADS), clean agent/waterless fire suppression system employing 3M Novec 1230 waterless
More informationSmartLine. RMA803 SmartLine Remote Fieldbus Indicator Specification 34-ST-03-90, December Technical Information.
SmartLine Technical Information RMA803 SmartLine Remote Fieldbus Indicator Specification 34-ST-03-90, December 2015 Introduction The Honeywell RMA803 is a Foundation Fieldbus remote indicator suitable
More informationVERSAFLOW VORTEX Supplementary instructions
VERSAFLOW VORTEX Supplementary instructions Vortex flowmeter Equipment category II 2G CONTENTS VERSAFLOW VORTEX 1 Safety instructions 3 1.1 General notes... 3 1.2 EC conformity... 3 1.3 Approval according
More informationUL TEST REPORT AND PROCEDURE
Issue Date: 2011-01-24 Page 1 of 18 Report Reference # E183863-A17-UL UL TEST REPORT AND PROCEDURE Standard: Certification Type: CCN: UL 60950-1, 2nd Edition, 2007-03-27 (Information Technology Equipment
More informationINSTRUCTION & SERVICE MANUAL
INSTRUCTION & SERVICE MANUAL D1xC COMBINED RADIAL HORNS & STROBES For Use In Hazardous Locations - Gas 3) Ratings and Markings The D1xC1 and D1xC2 combined alarm horns and strobes comply with the following
More informationKidde Nitrogen Inert Gas Clean Agent Fire Suppression System
1. GENERAL 1.1 INTENT OF SPECIFICATIONS A. This specification details the requirements for an engineered inert gas fire suppression system Model Kidde Nitrogen. These requirements, combined with good engineering
More informationSLATE. Burner Control Module INSTALLATION INSTRUCTIONS R8001B2001
SLATE Burner Control Module R8001B2001 INSTALLATION INSTRUCTIONS Scan for more information Application SLATE brings configurable safety and programmable logic together into one single platform. The platform
More informationIntrinsically Safe, NEMA 4, Type 4X, IP67 Loop-Powered Meter
PD685 Intrinsically Safe, NEMA 4, Type 4X, IP67 Loop-Powered Meter Actual Size Digits C US Intrinsically Safe 3½ Digits LARGE DISPLAY NEMA 4, Type 4X, IP67 Loop-Powered Field-Mount Process Meter 4-20 ma
More informationInstallation Guide. EXGP Oxygen Analyzer System (ATEX) Interface Electronics Unit
EXGP Oxygen Analyzer System (ATEX) Installation Guide Interface Electronics Unit DO NOT OPEN WHEN ENERGISED OR WHEN AN EXPLOSIVE GAS ABB The Company We are an established world force in the design and
More informationLimit Switch Box YT-870/875 SERIES
Limit Switch Box YT-870/875 SERIES PRODUCT MANUAL VERSION 1.01 Contents 1. Introduction 3 1.1 General information for the users. 3 1.2 Manufacturer Warranty 3 1.3 Explosion Proof Warning. 3 2. Product
More informationINSTRUCTION MANUAL. E2xB05 & E2xB10 Xenon Beacons For use in Hazardous Locations
INSTRUCTION MANUAL E2xB05 & E2xB10 Xenon Beacons For use in Hazardous Locations 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT DO NOT OPEN WHEN ENERGISED POTENTIAL ELECTROSTATIC CHARGING
More informationFixed Gas Detection System/Meridian CERTIFICATION
The marking shall include 2 Wire Aluminum Transmitter 3/4 Wire Aluminum Transmitter 2 Wire Stainless Steel Transmitter (PN: 096-3521) (PN: 096-3522) (PN: 096-3525) Ex db [ia Ga] IIC T4 Gb Ex db [ia Ga]
More informationCONTROL BE MADE CHANGES MAY NOT. Page 1
HI 6020IT and HI 6020JB US & Canada Hazardous Locations User Guide (Class I, II, III, Division 1, Class I, Zone 0 and Zone 20) Hardy Process Solutions Document Number: : 0596-0352-01 REV A CONTROL LLED
More informationFMP-ULS UNIVERSAL LIQUID SENSOR INSTALLATION GUIDE
FMP-ULS UNIVERSAL LIQUID SENSOR INSTALLATION GUIDE The information in this publication is provided for reference only. While every effort has been made to ensure the reliability and accuracy of the information
More informationORDINANCE NO
ORDINANCE NO. 2017-08-031 AN ORDINANCE OF THE CITY OF LANCASTER, TEXAS, REPEALING THE NATIONAL ELECTRICAL CODE 2014 EDITION IN ITS ENTIRETY AND REPLACING IT WITH THE ADOPTION OF THE NATIONAL ELECTRICAL
More informationSmartLine Pressure Transmitter ST 700 Basic Quick Start Installation Guide 34-ST-25-57, Revision 1, December 2016
SmartLine Pressure Transmitter ST 700 Basic Quick Start Installation Guide 34-ST-25-57, Revision 1, December 2016 This document provides descriptions and procedures for the Quick Installation of Honeywell
More informationSECTION LOW-VOLTAGE ELECTRICAL POWER CONDUCTORS AND CABLES (600 VOLTS AND BELOW)
SECTION 26 05 21 PART 1 - GENERAL 1.1 DESCRIPTION This section specifies the furnishing, installation, and connection of the low voltage power and lighting wiring. 1.2 RELATED WORK A. Excavation and backfill
More informationQuick Start Guide. XNX Universal Transmitter
Quick Start Guide XNX Universal Transmitter Table of Contents 1 Introduction...5 2 Warnings...6 3 Mounting and Location of Detectors...8 3.1 Mounting the XNX Universal Transmitter...8 4 Wiring the XNX
More informationRosemount Pipe Clamp Sensor. Reference Manual , Rev BA February 2014
Rosemount Pipe Clamp Sensor Reference Manual Reference Manual Title Page The Rosemount 0085 Pipe Clamp Sensor NOTICE Read this manual before working with the product. For personal and system safety, and
More informationInstallation Instructions for 116EXMLED Series AdaptaBeacon LED Lights for Use in Hazardous Locations. Description. Installation WARNING
Installation Instructions for 116EXMLED Series AdaptaBeacon LED Lights for Use in Hazardous Locations STANCHION 116EX-S CEILING 116EX-C 3/ CONDUIT ENTRIES PENDANT 116EX-P 3/ CONDUIT ENTRY 116EX-C (WALL
More informationElectrical Safety Requirements
Electrical Safety Requirements Purpose This document defines the minimum required control measures to reduce the risk of injury or illness related to electricity. Scope Applicable to all Coca-Cola system
More informationExplosion Proof Push Button Momentary Switch - C1D1, C2D1 - Adjustable Timer - 10 sec-170 Minutes
Explosion Proof Push Button Momentary Switch - C1D1, C2D1 - Adjustable Timer - 10 sec-170 Minutes Part #: EPS-PB10-MS-AT-V3 Made in the USA The Larson Electronics EPS-PB10-MS-AT-V2 Explosion Proof Push
More informationUL TEST REPORT AND PROCEDURE
Issue Date: 2010-12-01 Page 1 of 16 Report Reference # E252373-A31-UL UL TEST REPORT AND PROCEDURE Standard: Certification Type: CCN: Product: Model: Rating: UL 60950-1, 2nd Edition, 2014-10-14 (Information
More informationIECEx Certificate of Conformity
INTERNATIONAL ELECTROTECHNICAL COMMISSION IEC Certification Scheme for Explosive Atmospheres for rules and details of the IECEx Scheme visit www.iecex.com Certificate No.: IECEx UL 13.0039U issue No.:1
More informationEngineering Guideline. pac-carriers Type for Yokogawa ProSafe-RS
Engineering Guideline pac-carriers Type 9195 for Yokogawa ProSafe-RS 2 Engineering Guideline / Yokogawa ProSafe-RS 06.06.2017 Integrated solutions for Yokogawa R. STAHL offers a wide range of customized
More informationRosemount 8800D Series Vortex Flowmeter. Quick Start Guide , Rev FE October 2018
Rosemount 8800D Series Vortex Flowmeter 00825-0100-4004, Rev FE 1 About this guide This guide provides basic guidelines for the Rosemount 8800D Series Vortex Flowmeter. It does not provide instructions
More informationNorth American Cable Glands
North American Cable Glands INTRODUCTION Linking the future As the worldwide leader in the cable industry, Prysmian Group believes in the effective, efficient and sustainable supply of energy and information
More informationLevel instruments. Point level measurement - Capacitance switches. Pointek CLS100 5/9. Overview. Configuration
Level instruments Overview Configuration is a compact 2-wire inverse frequency shift capacitance switch for level detection in constricted spaces, interfaces, solids, liquids, slurries and foam. Benefits
More informationDräger Polytron 8200 CAT Detection of flammable gases and vapors
Dräger Polytron 8200 CAT Detection of flammable gases and vapors The Dräger Polytron 8200 CAT is an advanced explosion proof transmitter for the detection of flammable gases in the lower explosion limit
More informationINSTRUCTION & SERVICE MANUAL
INSTRUCTION & SERVICE MANUAL D2xC1 ALARM HORN AND STROBE For Use In Hazardous Locations 3) Ratings and Markings 3.1 ATEX / IECEx certification The D2xC1 Alarm Horn and Strobe complies with the following
More informationIntrinsically Safe Pressure Transmitters for installation in hazardous locations Models IS-20-S, IS-21-S, IS-20-F, IS-21-F WIKA Datasheet IS-20
Electronic Pressure Measurement Intrinsically Safe Pressure Transmitters for installation in hazardous locations Models IS-20-S, IS-21-S, IS-20-F, IS-21-F WIKA Datasheet IS-20 Applications Chemical, Petrochemical
More informationSET Installation and Operating Instructions. Level switch for one sensor
Labkotec Oy Myllyhaantie 6 FI-33960 PIRKKALA FINLAND Tel.: +358 29 006 260 Fax: +358 29 006 1260 7.11.2013 Internet: www.labkotec.fi 1/14 SET-1000 Level switch for one sensor Copyright 2013 Labkotec Oy
More informationExplosion Protected Panelboards D2Z Series
Eplosion Protected Panelboards D2Z Series Installation & Maintenance Information IF 1416 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE APPLICATION The D2Z Series panelboards provide a centrally controlled
More informationInstallation Instructions. Distinctive Electric Cooktop. Françis : voir page 11 Español: consulte la página Rev. A. Models DECT304, DECT365
Distinctive Electric Cooktop Models DECT304, DECT365 Installation Instructions 105643 Rev. A Françis : voir page 11 Español: consulte la página 21 Table of Contents Page Special Warnings... Product Dimensions
More informationINSTRUCTION MANUAL (ATEX / IECEx)
INSTRUCTION MANUAL (ATEX / IECEx) BExS110D and BExS110D-R Sounder For use in Flammable Gas and Dust Atmospheres BExS110D BExS110D-R 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT DO NOT
More informationVQ500 Series Combustible Gas Detector Elements
VQ500 Series Combustible Gas Detector Elements FEATURES * Optimised for combustible gases and vapours * Thermal conductivity versions available * Certified flameproof component * Integral pellistors *
More informationDräger Polytron 8700 IR Detection of flammable gases and vapors
Dräger Polytron 8700 IR Detection of flammable gases and vapors The Dräger Polytron 8700 IR is an advanced explosion proof transmitter for the detection of combustible gases in the lower explosion limit
More informationInstallation Instructions
Electric Heaters 5 --- 20 kw SMALL PACKAGED PRODUCTS (SPP) Accessory Electric Heaters For 13 SEER, R---410A, Z Chassis Installation Instructions NOTE: Read the entire instruction manual before starting
More informationNotes: Warrick Series 67 Intrinsically Safe Multi-Function Control Installation and Operation Bulletin
Notes: Warrick Series 67 Intrinsically Safe Multi-Function ontrol Installation and Operation Bulletin Form 670 Sheet P/N 100501-1 Rev. F Table of ontents Page 3 Page Page 5 Page 6 Page 7 Page 8 Page 9
More informationCertificate of Compliance
Certificate of Compliance Certificate: 1182963 (066027_0_000) Issued to: WIKA Instruments Ltd. 3103 Parsons Rd Edmonton, Alberta T6N 1C8 CANADA Attention: Robert Woo The products listed below are eligible
More informationDräger Polytron 8310 IR Detection of flammable gases and vapour
Dräger Polytron 8310 IR Detection of flammable gases and vapour The Dräger Polytron 8310 IR is an advanced explosion proof transmitter for the detection of combustible gases in the lower explosion limit
More informationRosemount 2051T In-Line Pressure Transmitter
Rosemount 2051T In-Line Pressure Transmitter 2051T In-Line Wireless Pressure Transmitter Configuration Transmitter Output Code 4-20 ma HART 2051 A 2051 with Selectable HART (1) Lower Power 2051 2051 with
More informationAdditional Operating Instructions SITRANS F. Vortex flowmeters. SITRANS FX330 Ex-d.
Additional Operating Instructions SITRANS F Vortex flowmeters Ex-d Edition 09/208 CONTENTS Safety instructions 3. General notes... 3.2 EU conformity... 3.3 Approval according to the IECEx scheme... 3.4
More informationYTA Series Temperature Transmitters [Style: S3] EN :2006, -11:2007, -26:2007. Supply circuit: Ui=30 V, Ii=165 ma,
User s Manual YTA Series Temperature Transmitters [Style: S3] Manual Change No. 10-008 Please use the attached sheets in the following manuals when the product is with /KU2 option and EN60000 Series based
More informationDuct heaters for ATEX/IECEx hazardous areas or in non-atex version
for ATEX/IECEx hazardous areas or in non-atex version * Non contractual picture Warning It is imperative to read these instructions carefully before installing or maintaining the equipment. MI200EN 09/2017
More informationELECTRONIC FLAME SUPERVISION MULTI-BURNER
MULTI-BURNER MODEL: SENS-A-FLAME II Revision: 0 7112 DESCRIPTION Model 7112 Sens-A-Flame II is a second generation solid-state programmable combustion safeguard for supervising multiple burner ovens, furnaces,
More informationRosemount 8800D Series Vortex Flowmeter
Quick Installation Guide Rosemount 8800D Rosemount 8800D Series Vortex Flowmeter Start Step 1: Mount the Flowmeter Step 2: Consider Housing Rotation Step 3: Set Jumpers and Switches Step 4: Connect Wiring
More informationElectronic 7 Installation Instructions
Electronic 7 Installation Instructions The Horstmann Electronic 7 is an advanced water heating control, which can be programmed to take advantage of cheap night-rate electricity, so that there is a tank
More informationIR1xxx Series 1, IR2xxx Series 1 Miniature Infrared Gas Sensors for Hazardous Areas and Intrinsic Safety in Mining
IR1xxx Series 1, IR2xxx Series 1 Miniature Infrared Gas Sensors for Hazardous Areas and Intrinsic Safety in Mining FEATURES * Configured for carbon dioxide (IR11BD, IR21BD), hydrocarbons (,,, ) or acetylene
More informationDräger Polytron 5100 EC Detection of toxic gases and vapors
Dräger Polytron 5100 EC Detection of toxic gases and vapors The Dräger Polytron 5100 EC is a cost-effective explosion proof transmitter for the detection of toxic gases or oxygen. It uses a high performance
More informationImmersion heaters for ATEX/IECEx hazardous areas or in non-atex version
for ATEX/IECEx hazardous areas or in non-atex version * Non contractual picture Warning It is imperative to read these instructions carefully before installing or maintaining the equipment. MI100EN 09/2017
More informationInstructions. Explosion Proof Smoke Detector U Rev: 9/
Instructions Explosion Proof Smoke Detector U0. Rev: 9/ 9-7 Table of Contents OVERVIEW... FEATURES... BENEFITS... SPECIFICATIONS... OPERATION... Warm Up... Outputs... Integral Wiring Compartment... LED...
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 26 0519 LOW-VOLTAGE ELECTRICAL POWER CONDUCTORS AND CABLES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationRadar Transmitters SITRANS LR400 (HART/PROFIBUS PA) Quick Start Manual 03/2013 SITRANS
Radar Transmitters SITRANS LR400 (HART/PROFIBUS PA) Quick Start Manual 03/2013 SITRANS SITRANS LR 400 Quick Start Manual This manual outlines the essential features and functions of the SITRANS LR 400
More informationCertificate of Compliance
FF0002 Certificate of Compliance Certificate: 2385571 Project 2447891 Issued to: Mine Safety Appliances 1000 Cranberry Woods Drive Cranberry Township, PA 16066 USA Issued by: Jocelyn Jens Product Group
More informationDräger Polytron 5200 CAT Detection of flammable gases and vapours
Dräger Polytron 5200 CAT Detection of flammable gases and vapours The Dräger Polytron 5200 CAT is a cost-effective explosion-proof transmitter for the detection of flammable gases in the lower explosion
More informationFire Alarm System Accessories
UL, ULC Approved* Fire Alarm System Accessories Intrinsically Safe Devices Single and Dual Channel Isolated Barrier Modules Features Single or dual channel intrinsically safe, transformer isolated barrier
More informationRosemount 2051 Pressure Transmitter with 4-20 ma HART and 1-5 Vdc HART Low Power Protocol
Quick Installation Guide August 2009 Rosemount 2051 Rosemount 2051 Pressure Transmitter with 4-20 ma HART and 1-5 Vdc HART Low Power Protocol Start Step 1: Mount the Transmitter Step 2: Consider Housing
More informationMODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL
TRACON MODEL FPT-130 SINGLE POINT FREEZE PROTECTION HEAT TRACE CONTROL TABLE OF CONTENTS FPT 130 Overview... 2 Installation... 3 Power Source and Load Connections... 4 Temperature Sensor... 5 External
More informationWFDE Series Waterflow Detector
WFDE Series Waterflow Detector The System Sensor WFDE series is compatible with pipe diameters ranging from 50mm through 200mm and can be mounted in a vertical or horizontal position. Features Compliant
More information