Installation Instructions for 116DEGEX-FJ-(R) AdaptaBeacon Fire Alarm Strobe Lights for Use in Hazardous Locations
|
|
- Elfrieda Hodge
- 6 years ago
- Views:
Transcription
1 Installation Instructions for 116DEGEX-FJ-(R) AdaptaBeacon Fire Alarm Strobe Lights for Use in Hazardous Locations CEILING 116EX-C 3/ CONDUIT ENTRIES PENDANT 116EX-P 3/ CONDUIT ENTRY 116EX-C (WALL MOUNTED) 3/ CONDUIT ENTRIES WALL 116EX-B 3" HUB 116 SERIES HOUSING AND GLOBE ASSEMBLY WITH GUARD Figure 1. Mounting Options Description The 116DEGEX-FJ (Gray housing) and 116DEGEX-FJ-R (Red housing) AdaptaBeacons are in-rush current limited strobe lights. When pendant, wall or ceiling mounted, and with dome guard removed, they meet or exceed the requirements of UL 1971 Signaling Appliance for the Hearing Impaired. The strobe is intended for indoor use in UL 1971 (signal appliance for the hearing impaired) listed compatiable fire alarm systems. The strobe flashes a 3 - degree beam of light approximately 65 times per minute with a UL cd ceiling and cd wall light output per Figure 7. The strobe is also UL 1638 (visual signal appliance, private mode) listed with dome guard installed for both indoor and outdoor use, and other applications requiring electrical supervision of the signaling circuit field wiring. In addition, the strobe is rated for outdoor use in Canada, the 116DEGEX-FJ(R) is listed to ULC-S (Visual Signal Device for Fire Alarm Systems), suitable for indoor and outdoor applications. The strobe features an enhanced synchronization circuit to comply with the latest requirements of UL 1971 and CAN/ ULC-S Synchronized operation requires a separately installed synchronization control module. See Table 1a for a list of compatible synchronization modules. When assembled with an available mounting subassembly (116EX(R)-P, 116EX(R)-C, or 116EX(R)-C with 116EX(R)-B and in accordance with these instructions, the 116DEGEX-FJ-(R) visual strobe signal is UL Listed as a Signaling Applicance for the hearing impaired for use in Class I, Division 1, Groups C and D, Class I, Division 2, Groups A, B, C and D, Class II Division 1, Group E, F and G, Class II, Division 2, Group F and G, and Class III Division 1 and 2 hazardous locations with Operating Temperature Codes per table 3. See Table 1 for Electrical Specifications. This strobe is UL and cul Listed as a Type 3R and 4X enclosure. See Figure 1. Installation Install this unit in accordance with the applicable requirements in the latest edition of the National Fire Alarm Code (NFPA 72), National Electrical Code (NFPA 70), and Canadian Electrical Code and CAN/ULC-S524-01/Standard for the Installation of Fire Alarm Systems. To reduce the risks of ignition of hazardous atmospheres and shock, do not apply power to the unit until installation has been completed and unit is tightly assembled and secured. 1. Mount using the following applicable method. a. Pendant Mount Models (Figure 2): Install the catalog number 116EX(R)-P, pendant mounting module, to the 116DEGEX-FJ-(R) main housing, tighten set-screw. Install explosion-proof hanger box (not supplied). Secure 3/ (19 mm) NPT threaded conduit (not supplied) to the box. Install the unit on the conduit. Ensure conduit enguages at least five full threads and then tighten the set-screw to secure the pendant mount module to the conduit. Connect field earth ground wire to ground screw or earth ground via conduit system. Wire in accordance with Figure 5. See table 3 for required supply wire temperature ratings. Phone: (800) Fax: (800)
2 6 3/ Set Screw(s) 12" 12 3/ Set Screw 5/16" 1" 13" 13 3/ 7 1/ 7 1/ Figure 2. Detail of Pendant Mounting Figure 3. Detail of Ceiling Mounting 12 9/16" 9 7/16" 1" 6 3/ 16 1/16" 5/16" 16 13/16" Set Screws Figure 4. Detail of Wall Bracket Mounting NOTE: DC polarity of circuit shown in supervisory state (signal inactive). Circuit polarity to reverse to activate signal. Electrical supervision requires wire run to be broken at each device. Device for constant input voltage. Do not connect to coded or pulsating voltage. KEY: Light symbol - NOTE: From Power Source or Previous Signaling Device Series 116DEX Series 116DEX Figure 5. Wiring Diagram Wire nut symbol - End-of-Line Resistor, when required with supervised system For non-fire alarm use, i.e. without field wire supervision, installer can tie the two white leads together and tie the two black leads together.
3 b. Ceiling Mount Models (Figure 3): Mount the catalog number 116EX(R)-C, ceiling/wall mounting module, using appropriate hardware (not supplied) suitable for the mounting surface. Connect field earth ground wire to ground screw or earth ground via conduit system. Wire the unit in accordance with Figure 5. See Table 3 for required supply wire temperature ratings. Install main housing to Ceiling mount module. Tighten the set-screw to secure the 116DEGEX-FJ-(R) main housing to the ceiling mount module. c. Bracket Mount Models (Figure 4): Install the catalog number 116EX(R)-C ceiling/wall mouting module using appropriate hardware (not supplied) for the mounting surface. Install the catalog number 116EX(R)-B wall mounting elbow to the 116DEGEX-FJ-(R) main housing. Tighten the set -screw to secure wall mounting module to the main housing. Run the unit's wiring through the elbow to the wall box. Connect field earth ground wire to ground screw or earth ground via conduit system. Wire the unit in accordance with figure 5. See table 3 for required supply wire temperature ratings. Install Table DEGEX-FJ-(R) AdaptaBeacon Strobe Light Electrical Specifications Voltage Designation* Max RMS Operating Current (A)** Regulated 24V DC 0.5 Regulated 24V FWR 0.5 CAUTION: To prevent damage to the signal circuit and to otherwise assure continued proper functioning, DO NOT operate the unit outside of the Regulated 24V DC/FWR voltage range of 16-33V DC/FWR (US), -31V DC/FWR (Canada). *The designation Regulated 24 refers to the voltage range of volts. **The Max RMS Operating Current is defined as the current rating over the entire voltage range. Model names Table 1a. Compatible Synchronization Modules Model numbers Auto-Sync Output SIGA-CC1S SIGA-MCC1S Module SIGA-CC1S-LG SIGA-MCC1S-LG Genesis signal Master- ADTG1M-RM MG1M-RM Remote Mount EG1M-RM XLSG1M-RM G1M-RM ZG1M-RM G1M-RM-LG main housing and 116EX(R)-B elbow subassembly to ceiling mount module. Tighten the set screw to secure the 116EX(R)-B elbow to the ceiling mount module. To reduce the risks of ignition of hazardous atmospheres and shock, keep assembly tightly closed when circuits are energized. 2. Apply power to the unit and ensure proper function. Maintenance atmospheres and shock, keep assembly tightly closed when circuits are energized. atmospheres and shock, disconnect from the supply and circuit and allow five (5) minutes for stored energy to dissipate before disassembling the unit. Disassemble the unit as follows (Figure 8): 1. Loosen the (3) guard screws and remove the guard. 2. Loosen the globe and ring assembly set screw. Insert a suitable tool into the notches in the globe and ring assembly and loosen the assembly by prying in a counterclockwise direction. Remove the ring and globe assembly. 3. Refer to Table 2 for the correct replacement catalog number and replace the necessary part. 4. To replace, simply screw the unit on until it seats firmly onto its gasket. Tighten the unit another 1/8 to 1/4 turn. Tighten the setscrew. 5. Reinstall the guard, where applicable, and secure using the three supplied screws. 6. After the unit is assembled, apply power and make sure the unit functions properly. Table DEGEX-FJ Mounting Options Catalog Electrical Conduit Flash Strobe Tube Description Number Ratings Size Rate Replacement Housing Less 116DEGEX-FJ-(R) 16-33V DC (US) N/A Approx. N/A Mounting Module -31V DC (Canada) 65 fpm 0.5/0.5A Ceiling/Wall 116EX(R)-C N/A 3/ NPT N/A N/A Mounting Module Pendant 116EX(R)-P N/A 3/ NPT N/A N/A Mounting Module Wall Bracket 116EX(R)-B N/A N/A N/A N/A Mounting Module
4 Effective Candela Light Output for Wall Bracket Mount Vertical Plane (Zero degree angle at side of globe) UL REQUIRED CD FOR RATING degrees 5 15 UL 1971 Hearing Impaired: cd wall NOTE: Optional dome guard shown, candela output readings taken without optional dome guard installed. Effective Candela Light Output for Ceiling Mount X & Y Planes (Zero degree angle at bottom of of globe) degrees UL REQUIRED CD FOR 125 RATING UL 1971 Hearing Impaired: 125 cd ceiling NOTE: Optional dome guard shown, candela output readings taken without optional dome guard installed. Figure 7. Light Output Patterns for 116DEGEX-FJ-(R)
5 Table 3. Ratings Operating Temperature Ambient Supply Wire Class I, Div. 2 Class I, Div. 1 & 2 Class II & III, Div. 1 Class II & III, Div. 2 Temp. Temp. Marking Groups A, B Groups C, D Groups E, F, G Group F, G C 75 C T2B (2 C) T6 (85 C) T4A (1 C) T4A (1 C) 55 C 90 C T2B (2 C) T6 (85 C) T4 (135 C) T4 (135 C) 65 C 5 C T2B (2 C) T6 (85 C) T3C (1 C) T3C (1 C) atmospheres and shock, keep assembly tightly closed when circuits are energized. atmospheres and shock, disconnect from the supply and circuit and allow five (5) minutes for stored energy to dissipate before disassembling the unit. Figure 8. Disassembly of the 116DEGEX-FJ-(R) AdaptaBeacon
6 U.S. T F Canada T F Asia T F Australia T F Europe T F Latin America T F
7 P/N OFFSET SPEC INSTALLATION INSTRUCTIONS FOR CATALOG SERIES 116DEGEX-FJ ADAPTABEACONS FOR USE IN HAZARD- OUS LOCATIONS (1) 11" X 17" SHEET AND (1) 8 1/2" X 11" SHEET PRINTED BOTH SIDES. FOLD 11" X 17" SHEET IN HALF AND IN- SERT 8 1/2" X 11" SHEET. FOLD TWO MORE TIMES TO DIMENSIONS SHOWN ON DETAIL WITH PART NUMBER ON THE OUTSIDE. MATERIAL: STANDARD WHITE OFFSET STOCK CHARACTERS: TO BE BLACK ON WHITE BACKGROUND NOTE: MECHANICALS HAVE ALREADY BEEN REDUCED TO ACTUAL SIZE. RETURN MECHANICALS TO: TECHNICAL WRITING EDWARDS SIGNALING 41 WOODFORD AVE. PLAINVILLE, CT 062 P/N FOLD DETAIL REFERENCE ONLY ECN: -C1923 Issue: 3 File: Approved by: GM
WARNING WARNING. Installation Instructions for 116DEXSTC-FJ AdaptaBeacon Fire Alarm Strobe Lights for Use in Hazardous Locations.
Cheshire, CT 064 3-699-30 (Ph) 3-699-3365 (Cust. Serv. Fax) 3-699-78 (Tech. Serv. Fax) Installation Instructions for 116DEXSTC-FJ AdaptaBeacon Fire Alarm Strobe Lights for Use in Hazardous Locations STANCHION
More informationInstallation Instructions for 116EXMLED Series AdaptaBeacon LED Lights for Use in Hazardous Locations. Description. Installation WARNING
Installation Instructions for 116EXMLED Series AdaptaBeacon LED Lights for Use in Hazardous Locations STANCHION 116EX-S CEILING 116EX-C 3/ CONDUIT ENTRIES PENDANT 116EX-P 3/ CONDUIT ENTRY 116EX-C (WALL
More informationINSTRUCTION MANUAL. D1xB2XH2 Xenon Beacon For use in Hazardous Locations. 2) Rating & Marking Information
INSTRUCTION MANUAL D1xB2XH2 Xenon Beacon For use in Hazardous Locations 2) Rating & Marking Information 2.1 Public Mode Fire Alarm Ratings The D1xB2XH2 is certified for use as public mode visual alarm
More informationINSTRUCTION MANUAL. D1xB2XH1 Xenon Beacon For use in Hazardous Locations. 2) Rating & Marking Information
INSTRUCTION MANUAL D1xB2XH1 Xenon Beacon For use in Hazardous Locations 2) Rating & Marking Information 2.1 Public Mode Fire Alarm Ratings The D1xB2XH1 is certified for use as public mode visual alarm
More informationINSTRUCTION MANUAL. D2xB1XH1 & D2xB1XH2 Xenon Beacons For use in Hazardous Locations
INSTRUCTION MANUAL D2xB1XH1 & D2xB1XH2 Xenon Beacons For use in Hazardous Locations synchronization requirements of UL1971 & UL1638 / CAN/ULCS526. 2.2 NEC & CEC Class / Division Ratings for US / Canada
More informationCode Master Factory Sealed Strobe Luminaires Explosionproof, Dust-Ignitionproof
Code Master Factory Sealed Strobe Luminaires Lighting Lighting: Explosionproof Visual Signal Applications Code Master Explosionproof Strobe fixtures are designed to provide safe operation in the presence
More informationstandards: standards:
INSTRUCTION MANUAL D2xB1LD2 LED Beacons For use in Hazardous Locations 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT DO NOT OPEN WHEN ENERGISED POTENTIAL ELECTROSTATIC CHARGING HAZARD
More informationInstallation Instructions for W2H Series Signals
Installation Instructions for W2H Series Signals IF1513 A Description and Operation DIMENSIONS W2H A 8 7/8" (225 mm) B 8 1/4" (210 mm) C 13" (330 mm) Figure 1. Speaker/Amplifier Dimensions The W2H signaling
More informationSELECT-A-HORN/STROBE SERIES
SELECT-A-HORN/STROBE SERIES Features Description Mircom s Select-A-Strobe/Horn Series is designed to comply with the Americans with Disability Act (ADA) and meet UL standard 1971 requirements for emergency
More informationGenesis Low Frequency (520 Hz) Horn-Strobe Installation Sheet
Genesis Low Frequency (520 Hz) Horn-Strobe Installation Sheet Table 1: Models Description Low frequency (520 Hz) horn, white housing, no FIRE marking, standard output clear strobe light Low frequency (520
More informationINSTRUCTION & SERVICE MANUAL
INSTRUCTION & SERVICE MANUAL D1xC COMBINED RADIAL HORNS & STROBES For Use In Hazardous Locations - Gas 3) Ratings and Markings The D1xC1 and D1xC2 combined alarm horns and strobes comply with the following
More informationSignature Series Auto-Sync Output Module (CC1S)
Signature Series Auto-Sync Output Module (CC1S) Product description Mounting The Signature Series can be mounted in a North American 2-1/2 in (64 mm) deep 2-gang box or a standard 4 in square box 1-1/2
More informationExplosion Proof Light Watt Metal Halide - Class 1 Div 1 & Class 2 Div 1
Explosion Proof Light - 400 Watt Metal Halide - Class 1 Div 1 & Class 2 Div 1 Part #: EPL-HB-400W-MH Made in the USA The EPL-HB-400W-MH metal halide, hazardous area light fixture from Larson Electronics
More informationINSTRUCTION & SERVICE MANUAL
INSTRUCTION & SERVICE MANUAL D2xC1 ALARM HORN AND STROBE For Use In Hazardous Locations 3) Ratings and Markings 3.1 ATEX / IECEx certification The D2xC1 Alarm Horn and Strobe complies with the following
More informationAddressable Detectors & Bases
Edwards Signaling Catalog u Intelligent Initiating Addressable Detectors & Bases Detectors: E-PD, E-PHD, E-HD Bases: B4U, RB4U, IB4U, SB4U Overview Edwards intelligent addressable detectors are meticulously
More informationINSTRUCTION MANUAL. E2xB05 & E2xB10 Xenon Beacons For use in Hazardous Locations
INSTRUCTION MANUAL E2xB05 & E2xB10 Xenon Beacons For use in Hazardous Locations 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT DO NOT OPEN WHEN ENERGISED POTENTIAL ELECTROSTATIC CHARGING
More informationInstallation and Maintenance Manual. Model 154XST Series Strobe Light for Use in Hazardous Conditions. français...page 21 español...
Model 154XST Series Strobe Light for Use in Hazardous Conditions Installation and Maintenance Manual 2561762C Rev. C0 913 Printed in U.S.A. français...page 21 español...página 43 Warranty Seller warrants
More informationApplications. Standard Materials
Mercmaster III Low Profile Compact Fluorescent Luminaires Compact Fluorescent listed for simultaneous exposure to combustible dusts and flammable gases or vapors. Applications Enclosed and gasketed fixtures
More informationFlex-Tone Explosionproof Electronic Signals ETH655 & ETH855 SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Installation
Flex-Tone Explosionproof Electronic Signals ETH655 & ETH855 Installation & Maintenance Information IF 1494 SAVE THESE INSTRUCTIS FOR FUTURE REFERENCE Description and Operation Cooper Crouse-Hinds Hazardous
More informationExplosion Proof LED Strobe Light - 4Hz Flash Rate - 10 Watts - Class I, Div. I - IP67
Explosion Proof LED Strobe Light - 4Hz Flash Rate - 10 Watts - Class I, Div. I - IP67 Part #: EPSLED-80 Page: 1 Made in Texas The EPSLED-80 Explosion Proof LED Strobe Light from Larson Electronics is UL
More informationPrint Specification. Publication. Instructions. Specific requirements. General requirements
Print Specification Publication GSA-CC1 Single Input Signal Module Installation Sheet P/N P-047550-1802-EN REV 04 ISS 23JUN15 Instructions This page is the print specification for the publication. It is
More informationModel 9001EXP Alarm. NOTE TO INSTALLER: Please leave this information with the Maintenance Department. LIMITED WARRANTY
INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS 1455 Kleppe Lane Sparks, NV 89431-6467 (775) 359-4712 Fax (775) 359-7424 E-mail: haws@hawsco.com website: www.hawsco.com Model 9001EXP Alarm No. 2080203(24)
More informationWE PROTECT HAZARDOUS ENVIRONMENTS EXPLOSION-PROOF AND HAZARDOUS LOCATION VISUAL & AUDIBLE SIGNALING PRODUCTS
WE PROTECT HAZARDOUS ENVIRONMENTS EXPLOSION-PROOF AND HAZARDOUS LOCATION VISUAL & AUDIBLE SIGNALING PRODUCTS 100+ YEARS Federal Signal is recognized as one of the industry s leading suppliers of safety
More informationLMV Series W Low Profile - Medium Base
L LMV Series 50-150W Low Profile - Medium Base Cl. I, Div. 2, Groups A, B, C, D Restricted Breathing Cl. I, Div. 2 & Zone 2 (Suffix S826) Certified for IEC Zone 2 (Suffix S826TB) Cl. II, Groups E, F, G;
More informationSIGA-CC1 Single Input Signal Module Installation Sheet
SIGA-CC1 Single Input Signal Module Installation Sheet Personality codes Use the personality codes described below to configure the SIGA-CC1 module. See Table 1 for listing information Table 1: Personality
More informationINSTRUCTION & SERVICE MANUAL D1xS1 & D1xS2 ALARM HORNS For Use In Hazardous Locations - Gas
INSTRUCTION & SERVICE MANUAL D1xS1 & D1xS2 ALARM HORNS For Use In Hazardous Locations - Gas UL 1203 CSA C22.2 NO. 30-M1986 The D1xS1 and D1xS2 Alarm Horns also comply with the following standards for signaling
More informationCSH24CH. Colored Light Strobe/Horn Series High Candela. Description. Features. Ceiling/Wall Mount Patent Pending. Ordering Information
OF FIRE CS24C Colored Light Strobe/orn Series igh Candela Ceiling/Wall Mount Patent Pending Description AMSECO's UL listed Colored Light Strobe CS24C series is designed to provide audible and visual signals
More informationOCH-SS series Direct Wired Units Indoor * and Outdoor Comfort Heaters
1200 North Main Street Fostoria, OH 44830 Phone: 800-495-4525 Fax: 419-435-0842 A DIVISION OF www.fostoriaindustries.com OCH-SS series Direct Wired Units Indoor * and Outdoor Comfort Heaters *EXCLUDING
More informationHomeland Security Light
Homeland Security Light Threat Level Status Indicator HSL Series > PLC compatible > Steady-on LED or incandescent light sources > Molded-in gasketed lens modules > Lens colors correspond to colors used
More informationExplosion Proof LED Light - Equivalent to Watt Metal Halide - Class 1 Division 2
Explosion Proof LED Light - Equivalent to 100-150 Watt Metal Halide - Class 1 Division 2 Part #: EPLC2-LED-150W Page: 1 Made in the USA The EPLC2-LED-150W LED hazardous area light fixture from Larson Electronics
More informationUSER INSTRUCTIONS FOR FLANGE IMMERSION HEATERS USED IN HAZARDOUS LOCATIONS
USER INSTRUCTIONS FOR FLANGE IMMERSION HEATERS USED IN HAZARDOUS LOCATIONS APPLICATION INDEECO Explosion proof Electric Immersion Heaters for Hazardous Locations are ccsaus Certified for use in areas (external
More informationGenesis LED G1 Series
EDWARDS Catalog u Strobes, Horns, Bells, Chimes LIFE SAFETY INCIDENT MANAGEMENT Genesis LED G1 Series Compact Notification Devices S218, S5389 7125-1657:0506 7135-1657:0502 Overview Genesis LED G1 Series
More informationINSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR PIPE THREAD IMMERSION HEATERS USED IN HAZARDOUS LOCATIONS
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR PIPE THREAD IMMERSION HEATERS USED IN HAZARDOUS LOCATIONS I. GENERAL Heatrex Explosion-proof Pipe Thread Mounted Immersion Heaters are CSA approved
More informationINSTRUCTION MANUAL (ATEX/IECEx/SIL2) BExBG05D-SIL Flameproof Xenon SIL 2 Beacons For use in Flammable Gas and Dust Atmospheres
INSTRUCTION MANUAL (ATEX/IECEx/SIL2) BExBG05D-SIL Flameproof Xenon SIL 2 Beacons For use in Flammable Gas and Dust Atmospheres 1) Introduction The BExBG05D-SIL is a flameproof beacon which is certified
More informationField Configurable Horns and Strobes
Vigilant Catalog Strobes, Horns, Bells, Chimes Field Configurable Horns and Strobes Genesis Series MNEC appliances available with clear or amber lenses. Pending Overview The Genesis line of fire alarm
More informationField Configurable Horns and Strobes
EDWARDS Catalog u Strobes, Horns, Bells, Chimes LIFE SAFETY & INCIDENT MANAGEMENT Field Configurable Horns and Strobes Genesis Series ECS/MNS appliances available with clear or amber lenses. S218, S5389,
More informationMODEL LP3 INSTALLATION AND SERVICE INSTRUCTIONS FOR STREAMLINE LP3 STROBE LIGHTS
Specifications subject to change without notice. USA 150303 Page 1 of 10 MODEL LP3 INSTALLATION AND SERVICE INSTRUCTIONS FOR STREAMLINE LP3 STROBE LIGHTS Specifications subject to change without notice.
More informations Notification Appliances
s Notification Appliances Data Sheet Fire Safety Products AS & AH Audible Horn Strobe / Audible Horn Appliances Application: Indoor / Outdoor AS-MC-CW AS-MC-R AH-R AH-W Product Overview Fast installation
More informationExplosion Proof Emergency Fluorescent Light Combination - Dimmable Ballast - C1D1-2 T8 lamps - 4'
Explosion Proof Emergency Fluorescent Light Combination - Dimmable Ballast - C1D1-2 T8 lamps - 4' Part #: EPL-EMG-48-2L-T8-D Made in the USA The Larson Electronics EPL-EMG-48-2l-T8-D Explosion Proof Emergency
More informationPotter Wall Mount Select-A-Strobe
104 Kenran Industrial Dr. Potter Wall Mount Select-A-Strobe SL-1224 SERIES SELECT-A-STROBE Call for additional listings 12 VDC with 15, 35 or 60 cd setting 24 VDC with 15, 35, 60, 5, 95 or 110 6 distinct
More informationEVLPF Series Compact Fluorescent
EVLPF Series Low Profile Hazard Gard Luminaires Cl. I, Div. 1, Groups B (GB Suffix), C, D Cl. I, Zone 1, Groups IIB + H2 (GB Suffix), IIB, IIA Cl. II, Div. 1, Groups E, F, G Class III, Simultaneous Presence
More informationTrueAlert Non-Addressable, Multi-Candela Notification Appliances Installation Instructions
TrueAlert NonAddressable, MultiCandela Notification Appliances Installation Instructions PRODUCT IDENTIFICATION REFERENCE (See Page 4 for Detailed Product Specifications) Type Mount Model Color Operation
More informationN2MVF Series Compact Fluorescent
Cl. I, Div. 2, Groups A, B, C, D Cl. II, Groups F, G Cl. III & Simultaneous Presence Marine & Wet Locations, R, 4, 4X; IP56 Applications: Champ Luminaires are used: In areas in which ignitable concentrations
More informationPILOT VALVE ENCLOSURES FOR HAZARDOUS LOCATIONS PENTAIR CLEAN AIR SYSTEMS
PENTAIR CLEAN AIR SYSTEMS 3-VFD COMBINATION FLAME AND DUST IGNITION PROOF ENCLOSURES Goyen pilot valve enclosures for hazardous locations are available in a combination of flame proof and dust ignition
More informationMounting Kits. LWMB2 6" 6 3 /8" 5 7 /8" 2.6 lbs lbs. LCMB2 6" 5" 5 3 /4 2.3 lbs. 2.5 lbs.
FEDERAL SIGNAL CORPORATION Mounting Kits Models LWMB2 and LCMB2 CUSTOM MOUNTING BRACKETS Heavy-duty construction Easy installation For walls and outside corners Indoor and outdoor use Replaces unsightly
More informationL-Series, Indoor Strobes and Horn Strobes
Notification Appliances L-Series, Indoor Strobes and Horn Strobes Indoor Selectable-Output Horns, Strobes and Horn Strobes for Wall Applications General The L-Series audible visible notification products
More informationMODELS ASHP, ASHH, ASUP, and ASUH
2562229A REV. A 1210 Printed in U.S.A. MODELS ASHP, ASHH, ASUP, and ASUH INSTALLATION AND SERVICE INSTRUCTIONS blank page INSTALLATION AND SERVICE INSTRUCTIONS FOR MODELS ASHP, ASHH, ASUP, AND ASUH SAFETY
More informationTrueAlert Multi-Candela Notification Appliances
UL, ULC Approved* TrueAlert Multi-Candela Notification Appliances Non-Addressable Visible Only Amber Lens Strobes for Emergency Communications Features Visible only (V/O) 24 VDC wall mount notification
More informationL-Series, Emergency Communication Devices
Notification Appliances L-Series, Emergency Communication Devices Description The L-Series Emergency Communications devices and accessories combine application versatility with all of the same time-saving
More informationMODELS 304GC, 304GCX, 314GC, and 314GCX
2562109A REV. A1 0317 Printed in U.S.A. MODELS 304GC, 304GCX, 314GC, and 314GCX INSTALLATION AND SERVICE INSTRUCTIONS FOR SELECTONE Limited Warranty This product is subject to and covered by a limited
More informationelevated ambient capability. in installations where moisture, dirt, dust, vibration, corrosion and rough usage are problems.
V Series H.I.D s VG, VN, VZ Series Wet Locations Marine Locations NEMA 3,3R,4,4X,7 < VG > < VN > < VZ > Type of Explosion-proof Fixture Wattage Class I Division 2 Group A,B,C,D Class II Division 1,2 Group
More informationINSTRUCTION MANUAL (ATEX / IECEx)
INSTRUCTION MANUAL (ATEX / IECEx) BExS110D and BExS110D-R Sounder For use in Flammable Gas and Dust Atmospheres BExS110D BExS110D-R 1) Warnings DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT DO NOT
More informationOPERATING AND INSTALLATION
A division of Signature Ind. Ltd YO6 YL6 V6 DIMENSIONS (mm) 280mm 11 OPERATING AND INSTALLATION INSTRUCTIONS FOR (UL & ATEX) YODALEX FLAMEPROOF AUDIBLE AND VISUAL ALARMS D7292 OPERATING CLASS 1 DIVISION
More informationPILOT VALVE ENCLOSURES FOR HAZARDOUS LOCATIONS
3-VFD COMBINATION FLAME AND DUST IGNITION PROOF ENCLOSURES Goyen pilot valve enclosures for hazardous locations are available in a combination of flame proof and dust ignition proof assemblies, where,
More information48W Fluorescent T8 Light w/ Emergency Backup Dimmable Ballast - (2) 2 Foot T8 Lamps - C1D2
48W Fluorescent T8 Light w/ Emergency Backup Dimmable Ballast - (2) 2 Foot T8 Lamps - C1D2 Part #: HAL-EMG-24-2L-T8-D Page: 1 Made in the USA The Larson Electronics HAL-EMG-24-2L-T8-D Hazardous Area Fluorescent
More informationCXH-A Forced-Air Heater
Installation and Operation Instructions CXH-A Forced-Air Heater CXH-A-0 EP to CXH-A-5 EP Class I - Groups C & D, Div. & 2 Class II - Groups E, F & G TB - 65 C (29 F) PF490-6-0242-004 July 20 Table A -
More informationWATLOW IND. WATROD Modular Duct Heater Installation & Maintenance Manual I&M NUMBER: Page: 1 Date:6/11/2008 Rev: 2
I&M NUMBER: 316-42-15-1 Page: 1 _ Pre Installation Check to make sure that heater received is the same as that ordered. Elements may come in contact with each other during shipment. Minor adjustments to
More informationXB Convection Heater. Convection Heaters. Applications. Special Wattage and Lengths. Selection of Temperature Code. Construction and Installation
The Series convection heater, with ratings up to 5000 watts, is designed for heating spaces where explosive substances are or may be present. The is available with either C CSA US or CE/ ATEX approvals.
More information08 Series Notification Appliances AS / AH & AS Audible Strobe Appliances and AH Audibles Application: Indoor / Outdoor
s Data Sheet Fire Safety & Security Products 08 Series Notification Appliances AS / AH & AS Audible Strobe Appliances and AH Audibles Application: Indoor / Outdoor AS-MC-CW AS-MC-R AH-W AH-R Product Overview
More informationTrueAlert Multi-Candela Notification Appliances
TrueAlert Multi-Candela Notification Appliances UL, ULC, CSFM Listed; FM Approved* Features 24 VDC high intensity notification appliance common features: Xenon strobe with intensity selectable as 135,
More informationCEC: Class I, Division 2, Groups A, B, C, D Class II, Division 1 and 2, Groups E, F, G Class III Enclosure 4X
Applications Enclosed and gasketed lighting fixtures for use in storage areas, tunnels, subways, chemical plants and other areas where moisture, dirt or corrosive atmospheres are a problem. Suitable for
More informationG Series SAVE THESE INSTRUCTIONS. (Model B) Convector Heater for Hazardous Locations GENERAL! INSTALLATION
G Series (Model B) Convector Heater for Hazardous Locations Type G-Series Convection Heaters are designed for use in Class I, Div. I hazardous environments. Units without control options are suitable for
More informationTYPE C: RETURN AIR UNDER POSITIVE PRESSURE FROM SEPARATE BLOWER
Installation Instructions Model AD-HR Air Duct Monitoring Housing INTRODUCTION The SIEMENS Model AD-HR is a sampling tube, air duct monitoring housing. When used with a compatible smoke detector, smoke
More information5 yr. Vitalite Rotating Warning Light. Models 121 and 121A LIGHT DUTY VEHICULAR LIGHT
FEDERAL SIGNAL CORPORATION Vitalite Rotating Warning Light Models 121 and 121A LIGHT DUTY VEHICULAR LIGHT Available in 12VDC and 24VDC Five dome colors 121 - Magnetic mount with cigarette lighter cord
More informationExplosion Proof UV/Visible Light Fluorescent Fixture - Paint Spray Booth, Rigs - Two Circuit Lamps
Explosion Proof UV/Visible Light Fluorescent Fixture - Paint Spray Booth, Rigs - Two Circuit Lamps Part #: EPL-48-2L-T8-VISUVA Page: 1 The Larson Electronics EPL-48-2L-T8-VISUVA Explosion Proof UV/Visible
More informationStandard Downrod for ceilings 8-10 feet high. Longer Downrod for ceilings 10 feet or higher
Table of Contents www.casablancafanco.com To register your fan, please visit: www.casablancafanco.com/register What to Expect with Your Installation Save your receipt for proof of purchase. Ceiling Bracket??
More informationCertificate of Compliance
FF0 001 Certificate of Compliance Certificate: 70116279 (LR 025993_0_000) Issued to: General Monitors, Incorporated 26776 Simpatica Circle Lake Forest, California 92630 USA Attention: Larry Vlagea The
More informationTable of Contents. What to Expect with. Tools Needed. Mounting Options. Blades
www.hunterfan.com Table of Contents Ceiling Bracket 30 inches Downrod Ladder 3 Wiring Operation, Maintenance & Cleaning Light Kit 11 Troubleshooting??? 16 15 1 12 10 9 5 Blades Canopy 6 4 PÁGINA 2 7 feet
More information56W Hazardous Location LED Fixture - C1D2 - Stainless Steel - Dimmable - DALI Network
56W Hazardous Location LED Fixture - C1D2 - Stainless Steel - Dimmable - DALI Network Part #: HALSS-ADC-48-2L-LED-D-V2 Page: 1 Made in the USA The HALSS-ADC-48-2L-LED-D-V2 Hazardous Location LED Fixture
More informationLTFX Electric Tank Immersion Heaters Installation Instructions
LTFX Electric Tank Immersion Heaters Installation Instructions 1 PN403-5 161-049178-101 March 2017 LTFX Electric Tank Immersion Heater Installation Instructions General The Chromalox Electric Tank Immersion
More informationWheelock RSS & RSSP Series
Wheelock RSS & RSSP Series Single- and Multi-Candela Strobes and Strobe Plates DF-51780:A G-520 General Wheelock s patented Series RSS Strobe Appliances and Series RSSP Strobe Plates have lower current
More informationGlobal Series. Installation and Maintenance Instructions. Model G-STR Strobe Beacon. For Use in Hazardous Locations
Global Series Model G-STR Strobe Beacon For Use in Hazardous Locations Ex d Surface Mount Ex de Surface Mount Installation and Maintenance Instructions 25500185 Rev. B4 1217 Printed in U.S.A. Limited Warranty
More informationCertificate of Compliance
FF0002 Certificate of Compliance Certificate: 2708418 Issued to: Gems Sensors Inc. 1 Cowles Road Plainville, CT 06062 USA Attention: Mr. Philip I. Draper The products listed below are eligible to bear
More informationL-Series, Indoor Strobes and Horn Strobes
Notification Appliances L-Series, Indoor Strobes and Horn Strobes Indoor Selectable-Output Strobes/Horn Strobes for Ceiling Applications General The L-Series audible visible notification products offer
More informationHazardous Location LED Pivoting Light - C1D2 - Dimmable - Modbus TCP/IP Network - Meets USCG Specs
Hazardous Location LED Pivoting Light - C1D2 - Dimmable - Modbus TCP/IP Network - Meets USCG Specs Part #: HALP-ANC-48-2L-LED-D-V2 Page: 1 Made in the USA The Larson Electronics HALP-ANC-48-2L-LED-D-V2
More informationExplosion Proof 160 W Class 1 & 2 Fluorescent UV Light With 4 Lamps - Class 1 Division 1
Explosion Proof 160 W Class 1 & 2 Fluorescent UV Light With 4 Lamps - Class 1 Division 1 Part #: EPL-48-4L-UV Page: 1 Made in the USA The Larson Electronics EPL-48-4L-UV 160 Watt Explosion Proof UV Fluorescent
More informationDETECT-A-FIRE Heat Detectors
DETECT-A-FIRE Heat Detectors DETECT-A-FIRE thermal detectors are detection and release devices used for fire detection systems to activate alarms and actuate extinguishing systems. This rate compensated
More informationTable of Contents What to Expect with. Mounting Options. Tools Needed. Downrod. Blades
Table of Contents Congratulations on purchasing your new Hunter ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains
More informationInstallation Instructions Model ABHW-4S
Installation Instructions Model ABHW-4S Intelligent Audible Base for Sleeping Area with 520Hz Low Frequency Sounder Introduction Application note The Model ABHW-4S audible base from Siemens Industry, Inc.
More informationExplosion Proof Combination Signal db (A) / 5 Joule
Explosion Proof Combination Signal - Operating instructions Additional languages www.r-stahl.com General information Contents 1 General information...2 1.1 Manufacturer...2 1.2 Information regarding the
More informationIntrinsically Safe, NEMA 4, Type 4X, IP67 Loop-Powered Meter
PD685 Intrinsically Safe, NEMA 4, Type 4X, IP67 Loop-Powered Meter Actual Size Digits C US Intrinsically Safe 3½ Digits LARGE DISPLAY NEMA 4, Type 4X, IP67 Loop-Powered Field-Mount Process Meter 4-20 ma
More informationPOINT HELIDECK LIGHTS PRL-EX-LSM LED v4 CLASS I, DIVISION 2 & ZONE 2
Compliances: ETL Listed Class I, Division 2, Groups A B C D, T6 at -40 deg C to +55 deg C ETL Listed Class I, Zone 2, Groups IIA, IIB+H2, IIC T6 at -40 deg C to +55 deg C ETL Listed to UL 844 & UL 1598
More informationTechnical Specification VFD
Technical Specification - 3-6 VFD Pilot valve enclosures suitable for use in hazardous certified environments. These enclosures are designed and tested to contain both flame and the ignition of dust and
More information'08 Series Notification A liances
SIEMENS Data Sheet Fire Safety & Security Products '08 Series Notification A liances AS I AH & AS - Audible Strobe Appliances and AH Audibles AS-MC-CW AS-MC-R AH-W AH-R Product Overview - Fast installation
More informationCertificate of Compliance
FF0002 Certificate of Compliance Certificate: 2385571 Project 2447891 Issued to: Mine Safety Appliances 1000 Cranberry Woods Drive Cranberry Township, PA 16066 USA Issued by: Jocelyn Jens Product Group
More informationLUCCI AIRFUSION QUEST II CEILING FAN
LUCCI AIRFUSION QUEST II CEILING FAN WITH IR REMOTE INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. V1.0 QUEST II IR
More informationStatic Pressure Alarm For Hazardous Location Fume Hoods
Static Pressure Alarm For Hazardous Location Fume Hoods Models: XPA1-0715 Class 1, Division 1, Group C, D 120V/15A/60Hz Pressure range 0.07 to 0.15 in-wg XPA1-1550 Class 1, Division 1, Group C, D 120V/15A/60Hz
More informationExplosion Resistant Unit Heater Owner s Manual This manual covers installation, maintenance, repair, and replacement parts.
EXUB Explosion Resistant Unit Heater Owner s Manual This manual covers installation, maintenance, repair, and replacement parts. Forced-Air Heater for Hazardous Locations Class I, Divisions 1 & 2, Groups
More information4' 2 Lamp Fluorescent Light Fixture - Emergency Battery Backup - T8 Bulbs - Multi-voltage - CID2
4' 2 Lamp Fluorescent Light Fixture - Emergency Battery Backup - T8 Bulbs - Multi-voltage - CID2 Part #: HALS-EMG-48-2L-T8 Made in the USA The Larson Electronics HALS-EMG-48-2L-T8 Hazardous Area Fluorescent
More informationBooster Power Supply Manual
Supply Manual DEVELOPED BY COPYRIGHT NOTICE General Signal Building Systems Corporation 6411 Parkland Drive Sarasota, FL 34243 (941) 739-4300 Copyright 1999 General Signal Building Systems Corporation
More informationNFPA 2001: Standard for Clean Agent Fire Extinguishing Systems NFPA 70: National Electrical Code (NEC) NFPA 72: National Fire Alarm Code
Part 1 - GENERAL 1.1 DESCRIPTION OF WORK A. Design and installation of an engineered Kidde ECS Advanced Delivery Systems (ADS), clean agent/waterless fire suppression system employing 3M Novec 1230 waterless
More information11:00 to 12:00 Secrets to achieving code-compliant strobe installations. Ralph Coco, Potter Canada Paul Jewett, Mircom Group of Companies
11:00 to 12:00 Secrets to achieving code-compliant strobe installations. Ralph Coco, Potter Canada Paul Jewett, Mircom Group of Companies Visible Signals Agenda 1. Physics 2. Installation Considerations
More informationTable of Contents. What to Expect with. Mounting Options. Tools Needed
Table of Contents www.hunterfan.com What to Expect with Your Installation Congratulations on purchasing your new Hunter ceiling fan! It will provide comfort and performance in your home or office for many
More informationUL Topic III. Converting European EEx Certificates. Into. North American Division Certificates
Note: While this material was originally prepared for presentation in February 1999, it has been updated to reflect the evolving technical requirements now applicable as of April 2003. UL Topic III Converting
More informationOwner s Guide and Installation Manual
Tribeca Owner s Guide and Installation Manual English Form# M6000-01 20120416 2012 Casablanca Fan Co. Welcome Your new Casablanca ceiling fan is an addition to your home or office that will provide comfort
More informationInstallation Instructions Type XPMC Air Heater for Hazardous Locations
Installation Instructions Type XPMC Air for Hazardous Locations 1 PF500-1 161-302639-005 May 2017 XPMC Air for Hazardous Locations 12", 2 Heat Sinks with Fixed Thermostat 12", 2 Heat Sinks with Adjustable
More informationConvection Heaters. Type XB. Product Description. Selection of Temperature Code. Construction and Installation. Special Wattage and Lengths
Product Description The XB, with ratings up to 5000 watts, is designed for heating spaces where explosive substances are or may be present. The XB is available with either CSA C/US or CE/ATEX approvals.
More informationMODELS SafeSite LED Linear, Class I Div. 1 2 & 4 Versions
INSTALLATION AND MAINTENANCE MANUAL SAFESITE LED LINEAR FIXTURE Document No: 9100-127-1402-99 Rev K December, 2016 MODELS SafeSite LED Linear, Class I Div. 1 2 & 4 Versions SUITABLE FOR WET LOCATIONS in
More informationCertificate of Compliance
Certificate of Compliance Certificate: 70067850 Date Issued: July 28, 2017 Issued to: Otis Instruments, Incorporated 301 S. Texas Ave. Bryan, Texas, 77803 USA Attention: Nicholas Sandera The products listed
More informationTechnical Manual for the Alarm Pull Station PH1
Technical Manual for the Alarm Pull Station PH1 Please note that every care has been taken to ensure the accuracy of our technical manual. We do not, however, accept responsibility for damage, loss or
More information