EcoSystem H-Series Ballasts Overview

Transcription

1 Fluorescent Dimming s Eco H-Series s Architectural Dimming Eco H-Series s Overview P/N rev B Eco H-Series digitally addressable ballasts provide a low-cost, flexible solution for any space in any application. Industry leading dimming to less than 1% meets the needs of the most demanding applications. Individual control with the Eco Digital Link eliminates the need to rewire, reduces design time, and provides a scalable solution from a small area to an entire building. Features ontinuous, flicker-free dimming from 100% to 1% or less for T8, and 1% for T5 and T5HO lamps ompatible with Eco Energi Savr NodeTM Units, GRAFIK Eye QS ontrol Unit, and Quantum software, allowing for integration into an existing/ planned Eco lighting control solution Programmed rapid start design preheats lamp cathodes before applying full arc voltage to ensure full-rated lamp life while dimming and cycling s turn on to any dimmed level without flashing to full brightness Low harmonic distortion throughout the entire dimming range maintains power quality Frequency of operation ensures that ballast does not interfere with infrared devices operating between 38 and 42 khz s maintain consistent light output for different lamp lengths, ensuring fixture-to-fixture uniformity Ultra-quiet operation Protected from miswires of any input power to control lead, or from lamp leads to each other and/or ground End-of-lamp-life protection circuitry ensures safe operation throughout entire lamp life Nonvolatile memory restores all ballast settings after power failure 100% compatible with all Eco digital controls 100% performance tested at factory 5-year limited warranty with Lutron field service commissioning (3-year standard warranty) from date of purchase. For additional Warranty information, please visit warranty/limited%20omm.pdf Eco H-Series, case type 1.18 in W (30 mm) x in H (25 mm) x in L (457 mm) Eco H-Series, case type G 2.38 in W (60 mm) x 1.0 in H (25 mm) x 9.5 in L (241 mm)

2 Fluorescent Dimming s Eco H-Series s Architectural Dimming Specifications Performance Dimming Range: 100% to 0.7% measured Relative Light Output (RLO) for T8, 100% to 1% measured relative light output for T5 and T5HO Starting: programmed rapid start urrent rest : less than 1.7 Flicker: none visible Light Output Variation: constant ±2% light output for line voltage variations of ±10% Life: average lamp life meets or exceeds rating of lamp manufacturer Power : greater than 0.95 Total Harmonic Distortion (THD): less than 10% Operating Voltage: Universal input 120 V, 220/ V, V at 50 or 60 Hz Frequency of Operation: greater than 42 KHz : 1.0/ for T8 lamps and 1.0 for T5 and T5HO lamps Maximum Inrush urrent: 3 A per ballast at V, 7A per ballast at 120 V Dimming Range for T8 lamps: BF Dimming Range (Max/Min (BF) Dimming Ratio / :1 1.0 / :1 Dimming Range for T5 and T5HO lamps: BF Dimming Range (Max/Min (BF) Dimming Ratio 1.0 / :1 P/N rev B Environment Minimum lamp starting temperature: 50 F (10 ) Relative humidity: less than 90% non-condensing Sound Rating: inaudible in a 27 db ambient Maximum ballast case temperature: 167 F (75 ) Standards alifornia Energy ommission Listed UL Listed (evaluated to the requirements of UL935) SA certified (evaluated to the requirements of 22.2 No. 74) lass P thermally protected Meets ANSI High Frequency Standard Meets F Part 18 Non-onsumer requirements for EMI/RFI emissions Meets ANSI ategory A surge protection standards up to and including 4 kv Manufacturing facilities employ ESD reduction practices that comply with the requirements of ANSI/ESD S20.20 Lutron Quality s registered to ISO Wiring & Mounting is grounded via a mounting screw to the fixture mounts using two screws (or sheet metal feature and one screw) within a fluorescent fixture. Power and lamp wiring terminals accept only one AWG or 0.75 mm mm 2 solid copper wire per terminal Seasoning Refer to the lamp manufacturer's requirements for lamp seasoning requirements prior to dimming.

3 Fluorescent Dimming s Eco H-Series s Architectural Dimming Eco H-Series s for Linear and U-Bend T8 s P/N rev B Type T8 and U-Bend Watts (length) 32 W (48 in) s per ase Size Eco H Series s Voltage (V ) 1 EHD T832 U EHD T832 U EHD T832 U EHD T832 U G EHD T832 G U G EHD T832 G U urrent (A) (BF) Power (W) Lumens* (lm) * (lm/w) (BEF) Relative (RSE) * Actual number may vary with lamp model. Please consult lamp manufacturer for lamp-specific data. For other lamp lengths, use a Hi-lume 3D ballast to match dimming performance.

4 Fluorescent Dimming s Eco H-Series s Architectural Dimming Eco H-Series T5 Linear s P/N rev B Type Watts (length) s per ase Size Eco H Series s Voltage (V ) urrent (A) (BF) Power (W) Lumens* (lm) * (lm/w) (BEF) Relative (RSE) T5 Linear 28 W (45.2 in) 1 EHD T528 U ,900 2,900 2, EHD T528 U ,800 5,800 5, Eco H-Series T5HO Linear s Type Watts (length) s per ase Size Eco H Series s Voltage (V ) urrent (A) (BF) Power (W) Lumens* (lm) * (lm/w) (BEF) Relative (RSE) T5HO Linear 54 W (45.2 in) 1 EHD T554 U ,000 5,000 5, EHD T554 U ,000 10,000 10, * Actual number may vary with lamp model. Please consult lamp manufacturer for lamp-specific data. For other lamp lengths, use a Hi-lume 3D ballast to match dimming performance.

5 Fluorescent Dimming s Eco H-Series s Architectural Dimming ase Dimensions P/N rev B A B A B in (457 mm) in (449 mm) (mounting centers) 1.0 in (25 mm) D 1.18 in (30 mm) D G A B D A 9.5 in (241 mm) E B 8.9 in (226 mm) (mounting centers) 7.1 in (180 mm) D 1.0 in (25 mm) E 2.38 in (60 mm)

6 Fluorescent Dimming s Eco H-Series s Architectural Dimming Eco H-Series Wiring Diagrams Eco Digital Link Overview The Eco Digital Link wiring (E1 and E2) connects the digital ballasts together to form a lighting control system Each Eco Digital Link supports up to 64 digital ballasts, 64 occupant sensors, 16 daylight sensors, and 64 wallstations or IR receivers Sensors do not directly connect to Eco H-Series ballasts No 3-wire phase control with Eco H-Series ballasts E1 and E2 (Eco digital link wires) are polarity insensitive and can be wired in any topology An Eco Energi Savr NodeTM, GRAFIK Eye QS ontrol Unit with Eco, or Quantum system provides power for the Eco Digital Link and supports system programming All Eco Digital Link programming is completed by using the Eco Programmer, GRAFIK Eye QS with Eco, or Quantum Eco Digital Link Wiring Eco Digital Link terminals only accept one AWG or 0.75 mm mm 2 solid copper wire per terminal Make sure that the supply breaker to the Digital and Eco Digital Link Supply is OFF when wiring onnect the two conductors to the two Digital terminals E1 and E2 as shown Using two different colors for E1 and E2 will reduce confusion when wiring several ballasts together The Eco Digital Link may be wired lass 1 or lass 2. onsult applicable electrical codes for proper wiring practices Notes P/N rev B neu n/c Hot e1 e2 neu n/c Hot e1 e2 line class 2 bus Terminals line lass 2 Bus Terminals To the Eco Digital Link Supply & up to 64 total ballasts The Eco Digital Link Supply does not have to be located at the end of the Digital Link Eco Digital Link length is limited by the wire gauge used for E1 and E2 as follows: Wire Gauge Digital Link Length (max) 12 AWG 2200 ft 14 AWG 1400 ft 16 AWG 900 ft 18 AWG 550 ft Wire Size Digital Link Length (max) 4.0 mm m 2.5 mm m 1.5 mm m 1.0 mm m 0.75 mm m

7 Fluorescent Dimming s Eco H-Series s Architectural Dimming P/N rev B Eco H-Series Wiring Diagrams T8, T5, and T5HO linear lamps Wiring to One ( case shown) blu blu Blue ReD ReD Red Wiring to Two s ( case shown) BLU BLU YEL YEL RED RED Blue Yellow Red Wiring to Three s (G case shown) BLU BLU YEL YEL B/W B/W RED RED Blue Striped Blue Yellow Red NOTIE Maximum ballast to lamp socket lead length is 7 ft (2 m) Wire colors shown are labeled on the ballast, but may vary depending upon fixture construction

8 Fluorescent Dimming s Eco H-Series s Architectural Dimming Eco Power Wiring Diagrams P/N rev B Neutral Black (onstant Hot) 2, 3 E1 NEU N/ HOT E1 E2 LINE lass 2 Bus Eco H-Series E2 Ground 1 1 is grounded via the case. 2 Wire colors shown are for Lutron controls and ballasts only. Dimming control wires may not match ballast wire colors. 3 The onstant Hot must not be wired to a switching device.

9 Fluorescent Dimming s Eco H-Series s Architectural Dimming Attention Electricians and ontractors Attention FAILITIES MANAGERS P/N rev B /Socket Leads Lead lengths from ballast to socket must not exceed 7 ft (2 m) for T8, T5, and T5HO linear lamps. Sockets sockets as per IE are required to ensure positive lamp-pin to socket contact. Mounting Many fluorescent lamp sockets are available with mounting slots to vary the height of the lamp away from the grounded metal surface. Use these slots to get the lamp glass to be 1/2 in ± 1/4 in away from the grounded metal surface for T8 lamps and 3/8 in ± 1/8 in for T5 and T5HO lamps. Having a fluorescent lamp too close to the grounded metal will make the minimum intensity too low and will reduce lamp life. Having a fluorescent lamp too far away from the grounded metal will make the lamp flicker or not turn on at all. PERFORMANE Seasoning onsult lamp manufacturer s recommendations on lamp seasoning prior to dimming. SERVIE Replacement Parts Use replacement parts with exact Lutron model numbers. onsult Lutron if you have any questions. Further Information For further information, please visit us at or contact our 24-hour Technical Support enter at Operating Temperature case temperature must not exceed 167 F (75 ) at any point on the ballast. Wiring and Grounding and lighting fixture must be effectively grounded. s must be installed per national and local electrical codes.