B OILER MAG XT. 2 flanged - COD flanged - COD flanged - COD flanged - COD flanged - COD.

Transcription

1 B OILER MAG XT Magnetic filters for heating systems of medium-large dimensions. 2 flanged - COD flanged - COD flanged - COD flanged - COD flanged - COD TECHNICAL FEATURES XT 2" XT 3" XT 4" XT 6" XT 8" CONNECTIONS 2" 3" 4" 6" 8" FILTRATION 1000 µm 1000 µm 1000 µm 1000 µm 1000 µm PN max 12 bar max 12 bar max 12 bar max 12 bar max 12 bar TEMPERATURE C C C C C FLOW RATE 20 m 3 /h 55 m 3 /h 85 m 3 /h 110 m 3 /h 140 m 3 /h DIMENSIONS H: 225 mm L: 260 mm ø: 170 mm H: 280 mm L: 360 mm ø: 220 mm H: 280 mm L: 360 mm ø: 220 mm H: 365 mm L: 470 mm ø: 325 mm H: 365 mm L: 525 mm ø: 325 mm PERFORMANCE MAGNETE MATERIAL EXTERNAL SUPERFICIAL FINISHING SEAL 9000 Gauss with high resistance Neodymium Iron Boron (NdFeB) powder-coated, black O-ring in viton MATERIALS BODY stainless steel 304 MAGNET GROUP OF THE TUBE stainless steel 316 grades aerospace quality EXTERNAL SUPERFICIAL FINISHING powder-coated, black SEAL O-ring in viton ADVANTAGES Reinforced polyamide body Neodymium magnet Used as additives loading BENEFITS Holds all impurities and debris of ferrous and not ferrous nature present inside the water Extension of boiler and circulator life MAIN FEATURES Magnetic filters Manta BoilerMag XT prevent black sludge formation (containing iron oxide), inside heating systems. Compatible with pipes of 1 ½ may be used in residential, commercial or industrial properties. Iron oxide reduces the thermal efficiency of heating systems and may seriously damage the boiler. The installation of BoilerMag XT, assures the protection of heating systems, guarantees a higher operation and extends system efficiency. BoilerMag XT Manta filters efficiently remove both magnetic and non-magnetic debris, leaving the heating system free from any contaminations and preventing their formation. Easy cleaning and installation. Patented magnetic core for the removal of iron oxides, magnetite and other debris.

2 APPLICATION AND USE To be installed in any domestic/civil heating circuit of small-medium dimensions. WHAT DO I NEED FOR THE INSTALLATION Typical plumber tool for connections of different type. CORRECT INSTALLATION For better performances, the device has to be installed as follow: 1. Identify a suitable location (see Where to Install p3). 2. Ensure enough clearance to carry out cleaning as the rods must be lifted out of the unit to clean. See dimensions in column B in the table below. 3. Mark and then cut out the correct length of pipe section to be removed to accommodate the BoilerMagXT unit and isolation valves. Ensure the cut is level and burr free. (Isolation valves are not included in the BoilerMagXT pack.) 4. Install appropriate isolation valves to the pipework and fit the valves to the two PN16 flanges (see below for flange dimensions). 5. Position the BoilerMagXT in place then align and secure the fittings to connect the unit to the valves. 6. Open the isolation valves and turn on the heating system 7. Complete the BoilerMagXT warranty card and return to Eclipse Magnetics. 8. Run the heating system at normal operating temperature and check installation integrity INSTALLATION DETAILS A B (mm) C (mm) 2"

3 FLANGE DETAILS PACKAGE CONTENT BoilerMag XT filter Opening/closing and magnet cleaning key Installation user s guide MAINTENANCE To maintain optimum efficiency we recommend cleaning annually. However when a BoilerMagXT is fitted to an existing heating system we recommend more regular checks as it is likely there will be a large build-up of ferrous oxide (black sludge) to clear out. 1. Switch off the heating system. 2. Isolate the heating system and close the isolation valves on either side of the BoilerMagXT unit. 3. Remove the black tricone positioned on the lid.

4 4. Lift out the magnetic cores using the handle on top of the unit. *Warning see below*. Be careful not to place the cores on or near ferrous items. Either place a bucket underneath or connect a hose to the 1 ¼ drain valve on the underside of the BoilerMagXT. Remove the drain plug and open the drain valve. 5. Partially open the inlet isolation valve and allow the contents to drain through the drain valve. When the draining water runs clear turn off the inlet isolation valve and allow the remaining contents to drain. 6. Close the drain valve and replace the plug. 7. Replace the magnetic core and hand tighten the black tricone to retain. 8. Re-open both isolation valves. If required open the vent shown on the top of the unit to release any trapped air.

5 TO BE USED WITH 1. BP 3 IN 1 COD BP L - COD BP L - COD BP 700A 1 L - COD BP L - COD OFFER DESCRIPTION Magnetic filters Manta BoilerMag XT prevent black sludge formation (containing iron oxide), inside heating systems. Compatible with pipes of 1 ½ may be used in residential, commercial or industrial properties. Iron oxide reduces the thermal efficiency of heating systems and may seriously damage the boiler. The installation of BoilerMag XT, assures the protection of heating systems, guarantees a higher operation and extends system efficiency. BoilerMag XT Manta filters efficiently remove both magnetic and non-magnetic debris, leaving the heating system free from any contaminations and preventing their formation. Easy cleaning and installation. Patented magnetic core for the removal of iron oxides, magnetite and other debris. COMPLIANCE This device is in compliance with Regulation UNI 8065 concerning heating systems for civil uses and Regulation UNI 9182 concerning planning, installation and test of supply systems of hot and cold water. ORIGIN OF THE PRODUCT Made in England DS Date of issue: 26/05/2017 Date of revision: Boiler Performance by Manta Ecologica S.r.l. Viale Archimede, Zevio (VR)