Networkable VAV Controller Specification and Installation Instructions

Transcription

1 Networkable VAV ontroller ontroller Models EVB14NIT0S EVB14NIT2S EVB14NIT4S EVB14NDT4S EVB14NIT0SF EVB14NIT4SF (0 TRIAS / pressure independent) (2 TRIAS / pressure independent) (4 TRIAS / pressure independent) (4 TRIAS / pressure dependent) (0 TRIAS / independent / feedback) (4 TRIAS / independent / feedback) TRL Series Thermostat TRL24 (Thermostat 2x4) TRLH24 (Thermostat 2x4 with Humidity) TRLG24 (Thermostat 2x4 with O 2 ) TRLGH24 (Thermostat 2x4 with O 2 and Humidity) EVB Series TDU Series Thermostat TDU10 TDU40 TDU70 (Grey LD, white enclosure) (Black LD, black enclosure) (Black LD, white enclosure) TRL24 Series TDU10 / TDU40 / TDU70 Series Description The EVB Series is a combination controller and thermostat with support for networked communications via the BAnet MS/TP or Modbus protocol. The EVB Series controller is compatible with both TRL24 and TDU series thermostats. The Networkable VAV ontroller is designed for simple and accurate control of any variable air volume box in a number of zone control configurations. Its field configurable algorithms enable versatile implementation of required control sequences. Features Field configured VAV algorithms, inputs and outputs Built-in actuator, 70 lb-in On board differential pressure sensor (select models) Select direction on analog outputs Simple air balancing and commissioning via thermostat Automatically sets operation mode to pressure dependent or independent based on the presence of air flow onfigurable PI (Proportional-Integral) function Independent, configurable proportional control band and dead band per ramp Selectable internal or external temperature sensor (10KΩ) Activate output with O 2 sensor from TRL/TDU or external sensor input hangeover by contact or external temperature sensor Internal and external temperature sensor calibration Optional potentiometer feedback for increased precision of actuator position Freeze protection Removable, raising clamp, non-strip terminals Operational Features Backlit LD with simple icon and text driven menus Select thermostat s default display Network service port via on-board mini USB connector Manual night setback or no occupancy override Multi level lockable access menu and setpoint Selectable Fahrenheit or elsius scale 3-wire connection to controller and 4 push buttons Applications Single duct, cooling only Single duct cooling and/or heating Up to 4 stage reheat and/or cool Up to 4 On/Off heat and/or cool Up to 4 time proportioned (TPM) heat or reheat Up to 2 analog (0-10Vdc) reheat and/or cool Up to 2 floating heat and/or cool Pressure dependent or pressure independent With or without auto changeover Supply/exhaust (requires an additional EV) Network ommunication BAnet MS/TP or Modbus communication port Select MA address via DIP switch or via network Automatic baud rate detection BAnet MS/TP Automatic device instance configuration opy & broadcast configuration via thermostat menu or via BAnet to other controllers BAnet scheduler Firmware upgradeable via BAnet Support OV (change of value) Modbus 9600, 19200, or bps RTU Slave, 8 bits (configurable parity and stop bits) onnects to any Modbus master EVB14-TRL-TDU Page 1

2 ontroller Specifications Description Torque Power consumption Running time through 90º Power supply Inputs On-board differential pressure sensor Outputs Real Time lock BAnet Modbus ommunication connection Electrical connection Operating temperature Storage temperature Relative Humidity Weight 70 in.lb. [8 Nm] at rated voltage 10 VA max 90 seconds 22 to 26 Vac 50/60 Hz Networkable VAV ontroller EVB Series 2 Universal inputs (Thermistor 10KΩ Type 3, digital 24Vac/dry contact, or 0-10Vdc) 2 digital inputs W (available on pressure independent models) 2 analog outputs (0-10 Vdc or 2-10Vdc; selectable) Up to 4 TRIA outputs 24 Vac, 500mA max thermal fuse in series with each TRIA output (on/off, pulse, or 2 floating outputs) Real-time clock (RT) with super capacitor backup (approximately 3 days) BAnet 9600, 19200, or bps (B-AS) Modbus RTU 9600, 19200, or Selectable parity and stop bit configuration: No parity, 2 stop bit Even parity, 1 stop bit Odd parity, 1 stop bit 24 AWG twisted-shield cable (Belden 9841 or equivalent). Maximum 50ft (15m) between controller and thermostat 0.8 mm 2 [18 AWG] minimum 0º to 50º [32ºF to 122ºF] -30º to 50º [-22ºF to 122ºF] 5 to 95% non condensing 1.8 kg. [4 lb] The actuator performs an auto-stroke on power up. When changing the actuator adjustment screws, cycle power to initiate the auto-stroke. EV with a built-in 70 in. lb. Actuator A D Dimensions A = mm B = mm = mm D = mm E = mm B Thermostat Specifications Description Temperature Sensor (TRL24 and TDU) Setpoint range 10º to 40º [50ºF to 104ºF] ontrol accuracy Display resolution Temperature: ±0.4º [0.8ºF] ±0.1º [0.2ºF] Humidity Sensor (TRLH24, TRLGH24 and TDU models with Humidity Sensors) Sensor range Display resolution 0.1% 5 to 95%RH O 2 Sensor (TRLG24, TRLGH24 and TDU models with O 2 Sensors) Other Operating principle Sensor Range Setpoint range Accuracy Self-calibrating, Non-Dispersive Infrared (NDIR) 0 to 2000 ppm 100 to 2000 ppm ±30 ppm ±3% of reading Response time 2 minutes by 90% Display resolution Electrical connection Network service port Power supply Power consumption Operating temperature Storage temperature Relative humidity 1 ppm TRL24 and TDU Series 3 wires to VAV controller and 2 wires to BAnet/Modbus network 0.8 mm 2 [18 AWG] minimum Mini USB connector 24Vac 1VA 0º to 50º [32ºF to 122ºF] -30º to 50º [-22ºF to 122ºF] 5 to 95 % non condensing Enclosure protection IP 30 (EN 60529) Weight 120 g. [0.25 lb] EVB Standard Page 2

3 Networkable VAV ontroller Dimensions A = mm B = mm = mm D = mm E = mm B TRL24 E D A = mm B = mm = mm D = mm E = mm F = mm G = mm E D TDU R.095 TYP A B G A F R6.542 TYP TDU Models Model # Temp RH O 2 PIR olor TDU TDU TDU TDU TDU TDU TDU TDU grey LD white enclosure TDU10 Series Model # Temp RH O 2 PIR olor TDU TDU TDU TDU TDU TDU TDU black LD black enclosure TDU TDU40 Series Model # Temp RH O 2 PIR olor TDU TDU TDU TDU TDU TDU TDU TDU black LD white enclosure TDU70 Series EVB Standard Page 3

4 Interface Networkable VAV ontroller TRL24.. AM PM.. MO TU WE TH FR SA SU %RH F ooling ON A: Automatic Heating ON A: Automatic Fan ON A: Automatic ommunication Status Menu Locked Programming mode (Technician setting) %RH Alarm status Energy saving mode (NSB or Occupancy) Percentage of humidity or F º: elsius scale ºF: Fahrenheit scale TDU %RH F AM PM Network ommunication Alarm Status User Lock Time ppm Parts Per Million Programming Mode (Technician Setting) Energy Saving Schedule Mode (NSB/O) F %RH A Automatic Mode ooling Heating º: elsius Scale ºF: Fahrenheit Scale %RH :Humidity Fan Mechanical Installation - Actuator 1. Manually close the damper blades and position the actuator to 0º or 90º. 2. Slide the actuator onto the shaft. 3. Tighten the nuts on the U bolt to the shaft with an 8mm wrench to a torque of 60 in-lb [6.7 Nm]. 4. Slide the mounting bracket under the actuator. Ensure free movement of the slot at the base of the actuator. Place the bracket pin at mid distance of the slot. 5. Affix the bracket to the ductwork with #8 self-tapping screws. Do not press the clutch when the actuator is powered. EV with a built-in 70 in. lb. Actuator MOUNTING BRAKET LUTH EVB Standard Page 4

5 Networkable VAV ontroller Mounting Instructions TRL24 AUTION: Remove power to avoid a risk of malfunction. A. Remove the captive screw that s holding the base and the front cover of the unit together. B. Lift the front cover of the unit to separate it from the base.. Pull all wires through the holes in the base. D. Secure the base to the wall using wall anchors and screws (supplied). Make the appropriate connections. E. Mount the control module on the base and secure using the screw. A B D E TDU AUTION: Remove power to avoid a risk of malfunction. A. Remove the wall mounting plate (highlighted) from the back of the thermostat. B. Install the mounting plate on the gang box.. Pull the wires through the base hole and make the appropriate connections. D. Mount the thermostat onto the wall plate. To mount the thermostat correctly, place the top of the thermostat on the mounting plate first and push it into the grooves to snap it into place. E. Secure the thermostat using the screw (supplied). A B D E BAnet or Modbus Address DIP Switch (DS1) MA address for communication, are selectable by DIP switch using binary logic. If you do not change device instance in program mode, it will be automatically modified according to the MA address. Note: Avoid using addresses above 246 when selecting Modbus MA address. MA Address DS.1 = 1 DS.2 = 2 DS.3 = 4 DS.4 = 8 DS.5 = 16 DS.6 = 32 DS.7 = 64 DS.8 = 128 Default Device Instance 0 OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF OFF ON OFF OFF OFF OFF OFF OFF ON ON ON ON ON ON OFF ON ON ON ON ON ON ON OFF * Slave addresses available by setting DS.8 to ON EVB Standard Page 5

6 Networkable VAV ontroller Wiring We strongly recommend that all Neptronic products be wired to a separate grounded transformer and that transformer shall service only Neptronic products. This precaution will prevent interference with, and/or possible damage to incompatible equipment. TRL24 and TDU TB Pwr Data High Total Pressure Low Static Pressure Optional: connect to enable service port TB Data Pwr JP3 (End of line) None = No end of line 120 Ohms = Last node on network RXD Flash receiving data via network TXD Flash transmitting data via network Status Flash communicating via thermostat Power On 24Vac applied to TB1 JP2 (TO3 / TO4 input voltage) INT = 24Vac supplied internally by TB1 EXT = Apply 24Vac to pin 5 of TB2 JP1 (TO1 / TO2 input voltage) INT = 24Vac supplied internally by TB1 EXT = Apply 24Vac to pin 1 of TB2 TXD RXD JP3 EOL Power Status INT EXT JP2 INT EXT JP1 TB1 TB2 TB3 TB4 TB5 TB6 ON DS B- (out) A+ (out) B- (in) A+ (in) DS1 DIP Switch The 8 DIP switches represent a binary logic to calculate the MA address. Default = all OFF AI2 AI1 AO2 AO1 DI2 DI1 TO4 TO3 24Vac input (TO3/TO4) TO2 TO1 24Vac input (TO2/TO1) 24Vac 24Vac 2 analog inputs (config.) External temp, changeover, normally cool/ heat, setpoint air flow, O2, air supply temp 2 analog outputs (config.) ool ramp 1 or 2, heat ramp 1 or 2, O2, setpoint airflow 2 digital inputs (config.) DI2: Override, normally cool/heat DI1: O open /close, NSB open /close 4 TRIA outputs (config.) ool 1 or 2, heat 1 or 2, O2 On/Off (config close/open percent) Floating (config float time) Pulse (heat only) Direct or reverse Power Input/Output 24Vac To other BAnet devices EVB Standard Page 6

7 PB Drawings Networkable VAV ontroller TRL24 Thermostat 3 wire cable (TB1 #1, 2 & 3) onnect TB1 #6 (A+) & #7 (B-) to EVB to enable the BAnet service port. Mode Selector Jumper RUN = Operation Mode PGM = Programming Mode PGM RUN JP1 A B TB PWR DATA A+ B- onnect to VAV controller Optional: connect to BAnet network to enable service port Mode Selection (JP1) JP1 JP1 RUN PGM RUN PGM RUN: Thermostat is in Operation Mode. Thermostat must be set in this mode for normal system operation. If not locked, setpoint and control mode can be changed by the end user. PGM: Thermostat is set in Programming Mode. Refer to the following sections for more details. O2 sensor (TRLG24 and TRLGH24 only) Avoid touching the O2 sensor as this may cause incorrect readings Temperature sensor (all models) Humidity sensor (TRLH24 and TRLGH24 only) BAnet service port TDU Thermostat 3 wire cable (TB1 #1, 2 & 3) onnect TB1 #6 (A+) & #7 (B-) to EVB to enable the BAnet service port. Mode Selector Jumper RUN = Operation Mode PGM = Programming Mode Thermostat Display Universal (TDU) JP1 RUN PGM TB PWR DATA onnect to EVB A+ B- Optional: connect to BAnet network to enable service port Mode Selection (JP1) JP1 JP1 RUN PGM RUN PGM RUN: Thermostat is in Operation Mode. Thermostat must be set in this mode for normal system operation. If not locked, setpoint and control mode can be changed by the end user. PGM: Thermostat is set in Programming Mode. Refer to the following sections for more details. O2 sensor Avoid touching the O2 sensor as this may cause incorrect readings BAnet service port Temperature sensor (all models) Humidity sensors (models with humidity) Access to Menus The menu overviews and options are the same for both TRL24 and TDU thermostats. However, the action button or the button used to access the menus and save changes is different in the thermostats. Use the following menu overviews with the appropriate action button as per your thermostat. Action Buttons on Thermostat Action Button TRL24 TDU Task Press to access the programming menus and save any changes. Press to return to the previous step without saving. EVB Standard Page 7

8 Networkable VAV ontroller Pressure & Applications Menu (1 of 6) Pressure and Applications For a description of the default settings for each application refer to Annex A: ontrol Apps on page 18. Main Menu Main Menu Sub Menu onfiguration PrSs (Pressure) Pressur Mode BV.50 Ind (independent ) dep (dependent ) *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** BV.52 Pressur Mode Auto hange OFF (disabled) ON (enabled ) "APPS " Motor Minimum Pos ooling 10% (0-100) AV.90 Motor Minimum Pos Heating 10% (0-100) AV.91 "APPS" APPS (Applications ) InPt (Inputs) OutP (Outputs) ontrol Apps l (cool only ) lht (cool & heat) Hrh (cool, heat, & reheat) O2 (carbon dioxide) itos (ITOS) FPbo (fan powered box ON) FPbA (fan powered box Auto ) onfirm ontrol apps NO (cancel) YES (confirm) "InPt" The APPS represent pre -defined default settings for selected applications. If you select Yes, the settings in Annex A will be applied and override any values already configured. We recommend selecting the `ontrol Apps` before changing any other configurations. Once selected, certain configurations, such as NSB, proportional bands, and deadbands, will be erased and reset to factory default values. tmp (Temperature) Mot (Motor) Setc (Settings) rmp (Ramps) NET (Network) HrS (Time & Date) OPt (Options) Only available with O 2 sensor models EVB Standard Page 8

9 Inputs Menu (2 of 6) AI1, AI2, DI1 and DI2 Main Menu Sub Menu onfiguration *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** Networkable VAV ontroller Main Menu PrSs (Pressure ) APPS (Applications ) InPt (Inputs) onfig Input AI1 AI2 DI1 DI2 * = StFl not available on pressure dependent model EVB14NDT4S AI1 AI1 Signal Type MSV.1 OFF (disabled) EtS (external temp sensor) SENs (sensor) Nol (normally cool ) NoHt (normally heat ) StFl*(setpnt airflow 0-10Vdc) O2 (carbon dioxide) ASt (Air supply temp sensor ) mor (Motor position ) AI2 AI2 Signal Type MSV.2 "AI2" H Over Setpnt 24 "AI2" O2 Maximum Range 2000 ppm "AI2" AV.58 AV.140 "AI2" O2 Setpnt 800 ppm AV.141 To display O2 without generating an alarm, use a setpoint higher than 2000ppm or the O 2 Maximum Range (highest of the 2). Appears only if using thermostats with temperature and humidity sensors. For TRLG, TRLGH and TDU thermostats with O2 sensors, go to OptҸmenu. O2 DISPLAY BV.65 NO YES When set to YES, the unit will not display the time when in Operation Mode "AI2" OFF (disabled) "DI1" OutP (Outputs) tmp (Temperature) Mot (Motor) Setc (Settings) rmp (Ramps) EtS (external temp sensor) SENs (sensor) Nol (normally cool ) NoHt (normally heat ) StFl*(setpnt airflow 0-10Vdc) O2 (carbon dioxide) ASt (Air supply temp sensor ) mor (Motor position) NSB-O ontact MSV.10 DI1 OFF Oo (occupancy open) Oc (occupancy closed) nsbo (night set back open) nsbc (night set back closed) H Over Setpnt 24 "DI1" O2 Maximum Range 2000 ppm "DI1" "DI2" No O Overide Delay Min 120 min (0-180) AV.61 NSB Overide delay Min 120 min (0-180) AV.58 AV.140 AV.60 "DI1" O2 Setpnt 800 ppm No O Heating setpnt 16 / 61 F NSB Mode StP (setpoint) Off AV.141 To display O2 without generating an alarm, use a setpoint higher than 2000ppm or the O 2 Maximum Range (highest of the 2). AV.19 BV.20 Appears only if using thermostats with temperature and humidity sensors. For TRLG, TRLGH and TDU thermostats with O 2 sensors, go to OptҸmenu. O2 DISPLAY BV.65 NO YES When set to YES, the unit will not display the time when in Operation Mode No O ooling setpnt 28 / 82 F AV.18 "DI1" "DI2" NET (Network) HrS (Time & Date) OPt (Options) Only available with O 2 sensor models DI2 Signal Type MSV.14 DI2 OFF Ovrd (override all) OVH1 (override heat 1) OVH2 (override heat 2) OVHt (override all heat ) Nol (normally cool ) NoHt (normally heat ) NSB Heating setpnt 16 / 61 F "OutP" DI2 ontact NO (normally open) N (normally closed) "OutP" AV.19 BV.36 NSB ooling setpnt 28 / 82 F DI2 Delay Seconds 120 (0-3600) AV.18 AV.64 NSB Motor Mode Auto OPEn "OutP" MSV.36 "OutP" EVB Standard Page 9

10 TRIA Outputs Menu (3 of 6) TO1 to TO4 Main Menu Main Menu Sub Menu onfiguration PrSs (Pressure) APPS (Applications) InPt (Inputs) OutP (Outputs) tmp (Temperature ) Mot (Motor) The number of Triac outputs (TO) depend on the model. S = motor/actuator. TO(S) = None T2(S) = 2 T4(S) = 4 Output onfig TO1 TO2 TO3 TO4 AO1 AO2 ầ = Auto and On options are for fan powered box applications and are only available with models: - EVB14NIT4S - EVB14NDT4S - EVB14NIT4SF *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** TO1 Ramp OFF r1 (cooling ramp 1) r2 (cooling ramp 2) Hr1 (heating ramp 1) MSV.25 TO1 Hr2 (heating ramp 2) O2 (carbon dioxide ) Auto (fan follows demand ) On (fan continuously on ) TO2 Ramp MSV.27 TO2 OFF r1 (cooling ramp 1) r2 (cooling ramp 2) Hr1 (heating ramp 1) Hr2 (heating ramp 2) O2 (carbon dioxide ) Auto (fan follows demand ) On (fan continuously on ) "TO2" TO1 Signal Type MSV.26 OnOf (on/off) FLt (floating ) PuLs (pulsed ) * * = Only if Hr1 or Hr2 is selected "TO1 lose Percent " "TO1 DIR-REV" "TO3" TO2 Signal Type OnOf (on/off) PuLs (pulsed ) "TO2 lose Percent " "TO2 DIR-REV" MSV.28 TO1 lose Percent 40% (15-80%) TO1-TO2 Floating Time in Sec 100 sec (15 to 250 /420 secs) AV.75 TO2 lose Percent 40% (15-80%) If O2 was selected AV.77 AV.79 TO1 Open Percent 0% [0-(TO1 cls pos-4)] TO2 Open Percent 0% [0-(TO2 cls pos-4)] Networkable VAV ontroller AV.78 AV.80 TO1 DIR-REV DIR (direct ) REV (reverse) TO1-TO2 DIR -REV DIR (direct ) REV (reverse) TO2 DIR-REV DIR (direct ) REV (reverse ) BV.32 BV.30 BV.33 "TO2" "TO3" "TO3" Setc (Settings) rmp (Ramps) NET (Network) TO3 Ramp OFF r1 (cooling ramp 1) r2 (cooling ramp 2) Hr1 (heating ramp 1) Hr2 (heating ramp 2) MSV.29 TO3 O2 (carbon dioxide ) Auto (fan follows demand ) On (fan continuously on ) "TO4" TO3 Signal Type OnOf (on/off) FLt (floating ) PuLs (pulsed) * MSV.30 * = Only if Hr1 or Hr2 is selected "TO3 lose Percent " "TO3 DIR-REV" If O 2 was selected TO3 lose Percent TO3 Open Percent 40% (15-80%) AV.81 0% [0-(TO3 cls pos-4)] TO3-TO4 Floating Time in Sec 100 sec (15 to 250 /420 sec s) AV.76 AV.82 TO3 DIR -REV DIR (direct) REV (reverse ) TO3-TO4 DIR -REV DIR(direct ) REV (reverse) BV.34 BV.31 "TO4" "AO1" HrS (Time & Date) OPt (Options) Only available with O 2 sensor models TO4 Ramp MSV.31 TO4 OFF r1 (cooling ramp 1) r2 (cooling ramp 2) Hr1 (heating ramp 1) Hr2 (heating ramp 2) O2 (carbon dioxide ) Auto (fan follows demand ) On (fan continuously on ) "AO1" TO4 Signal Type OnOf (on/off) PuLs (pulsed ) "TO4 lose Percent " "TO4 DIR-REV" MSV.32 TO4 lose Percent 40% (15-80%) AV.83 TO4 Open Percent 0% [0-(TO4 cls pos-4)] AV.84 TO4 DIR -REV DIR (direct ) REV (reverse) BV.35 "AO1" EVB Standard Page 10

11 Analog Outputs Menu (4 of 6) AO1 and AO2 Main Menu Sub Menu onfiguration Networkable VAV ontroller Main Menu PrSs (Pressure ) APPS (Applications ) InPt (Inputs) OutP (Outputs) tmp (Temperature) Mot (Motor) Output onfig TO1 TO2 TO3 TO4 AO1 AO2 * = StFl not available on pressure dependent model EVB14NDT4S = Auto and On options are for fan powered box applications and are only available with models: *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** AO1 Ramp MSV.20 AO1 OFF r1 (cooling ramp 1) r2 (cooling ramp 2) Hr1 (heating ramp 1) Hr2 (heating ramp 2) O2 (carbon dioxide) StFl (stpnt airflow 0-10Vdc)* Auto (fan follows demand ) On (fan continuously on ) AO2 Ramp MSV.22 AO2 OFF r1 (cooling ramp 1) r2 (cooling ramp 2) Hr1 (heating ramp 1) Hr2 (heating ramp 2) O2 (carbon dioxide) StFl (stpnt airflow 0-10Vdc)* Auto (fan follows demand ) On (fan continuously on ) "AO2" AO1 Minimum Voltage 0.0 Vdc "tmp" AO2 Minimum Voltage 0.0 Vdc AV.70 AV.72 AO1 Maximum Voltage 10.0 Vdc AO2 Maximum Voltage 10.0 Vdc AV.71 AV.73 AO1 DIR-REV DIR (direct) REV (reverse) AO2 DIR-REV DIR (direct) REV (reverse) BV.25 BV.26 "AO2" "tmp" Setc (Settings) - EVB14NIT4S - EVB14NDT4S - EVB14NIT4SF rmp (Ramps) NET (Network) HrS (Time & Date) OPt (Options) Only available with O 2 sensor models EVB Standard Page 11

12 Settings Menu (5 of 6) Temp, Motor, Settings and Ramps Main Menu Main Menu PrSs (Pressure) Sub Menu Intern Temp Sensor Offset Actual temp / F AV.10 Extern Temp Sensor Offset Actual temp / F AV.11 (± 5 / ± 10 F) Appears only if AI1 or AI2 = EtS onfiguration *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** (± 5 / ± 10 F) User Minimum Setpnt 15.0 / 59 F (10 -AV.17 / 50 F-AV.17) AV.16 User Maximum Setpnt 30.0 / 86 F (AV / AV F) AV.17 Networkable VAV ontroller User Setpnt Locked No (unlocked) Yes (locked ) BV.2 APPS (Applications) InPt (Inputs) OutP (Outputs) Motor Signal Ramp OFF~ r1 (cooling ramp 1) r2 (cooling ramp 2) MSV.35 Motor DIR-REV DIR (direct ) REV (reverse) BV.40 User Setpnt 22.0 / 72 F (Av.16 AV.17) "SEtc" AV.15 Temp ontrol Sensor MSV.4 ItS (internal sensor) EtS (external sensor) NEt (network) EtS appears only if AI1 or AI2 is set to EtS "mot" Network timeout Minutes 5 min (0-60 min) AV.145 "mot" tmp (Temperature) Hr1 (heating ramp 1) Hr2 (heating ramp 2) StFl (stpnt airflow 0-10Vdc) or (changeover ramp) H1 (cool/heat) Mot (Motor) ANLg (analog 0-10Vdc) Setc (Settings) rmp (Ramps) Temp ontrol Mode MSV.17 Auto (automatic all modes) HEAt (heat/off) OOl (cool/off) ON (manual heat/cool) LHt (auto/off) BV.3 Enable onoff ontrol Mode No (Disabled) Yes (Enabled) Display Info MSV.95 t c (temp & demand) StP (setpoint & demand) t c (temp only) StP (setpoint) OFF (no display: blank) Freeze Protect No (Disabled) Yes (Enabled) BV.6 * = Airflow integral is not functional on pressure dependent model EVB14NDT4S, ignore the option. ooling anti cycle minutes 2 min (0-15 min) AV.51 NET (Network) HrS (Time & Date) OPt (Options) Only available with O2 sensor models Ramp Setting Or (changeover) r1 (cooling ramp 1) r2 (cooling ramp 2) Hr1 (heating ramp 1) Hr2 (heating ramp 2) l Ht Switch Time in Minutes 0 min (0-120 min) AV.170 Airflow Intgral time in Min 0 min (0-60 min)* AV.106 H Over Prop Band AV / 4.0 F (0.5-5 / 1-9 F) R1 Prop Band AV / 4.0 F (0.5-5 / 1-9 F) R2 Prop Band AV / 4.0 F (0.5-5 / 1-9 F) Heating Intgral time in Sec 0 sec (0-250 sec) AV.30 H Over Dead Band AV / 0.6 F (0-5 / 0-9 F) R1 Dead Band AV / 0.6 F (0-5 / 0-9 F) R2 Dead Band AV / 0.6 F (0-5 / 0-9 F) "r1" "r2" "Hr1" ooling Intgral time in Sec 0 sec (0-250 sec) AV.50 Fan Always On Mode On (always on) OFF (follows NSB/NoOcc) BV.100 BV.100 = For fan powered box applications and available only with models: - EVB14NIT4S - EVB14NDT4S - EVB14NIT4SF "rmp" Hr1 Prop Band AV / 4.0 F (0.5-5 / 1-9 F) Hr2 Prop Band AV / 4.0 F (0.5-5 / 1-9 F) Hr1 Dead Band AV / 0.6 F (0-5 / 0-9 F) Hr2 Dead Band AV / 0.6 F (0-5 / 0-9 F) "Hr2" "NEt" The analog or Triac output ramps must be set to On On = Fan is always on (continuous). Off = Fan is off if control mode is off or if there is no demand when in NSB or No Occupancy mode via digital input or schedule. EVB Standard Page 12

13 Settings Menu (6 of 6) Network, Time and Options Main Menu Sub Menu onfiguration Networkable VAV ontroller Main Menu *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** PrSs (Pressure) APPS (Applications) InPt (Inputs) OutP (Outputs) tmp (Temperature) Mot (Motor) Network onfig type (Type ) mod ba PYc (copy config) If type = ba, menu contains "type", "ba" and "PYc" If type = mod, menu contains "type" and "mod" Network hoice ba (BAnet) mod (Modbus) Modbus Auto Baud Rate No (Manual) Yes (Automatic) BAnet Auto Baud Rate No (Manual) Yes (Automatic) Start Address 0 (0-254) AV.165 "BAnet Auto Baud Rate" "Modbus Auto Baud Rate" Modbus Baud Rate 57.6k (9.6k, 19.2k, 38.4, 57.6k) Modifiable only if Auto Baud Rate set to "No". Bacnet Baud Rate 76.8k (9.6k, 19.2k, 38.4, 76.8k) Modifiable only if Auto Baud Rate set to "No". End Address (0-254: max=start + 63) AV.166 Modbus omport onfig NP2s (no parity, 2 stop bits) EP1s (even parity, 1 stop bit) OP1s (odd parity, 1 stop bit) MSTP MA Address 0 (0-254) Modifiable only if all DS1 DIP switches are set to OFF. onfirm opy onfig No (cancel) Yes (confirm) 1000 BV.90 Modbus Address 1 (1-246) Modifiable only if all DS1 DIP switches are set to OFF (device instance) "HrS" opy onfig in (in progress) "HrS" MSTP MAX Master 127 (1-127) opy onfig Result Succeed AV.167 Refer to opy onfig Annnex for a complete list of messages and error codes. "PYc" "HrS" Setc (Settings) Local Time Local Time Local Date rmp (Ramps) Set Time Display format 24 (24-hour format) 12 (AM/PM format) Hours 12 (0-23 or 1-12 am/pm) Minutes 00 (00-59) Year 15 (15-99) NET (Network) Appears only if using TRLG or TRLGH or TDU thermostats with O2 sensors. Appears only if using TRLG or TRLGH or TDU thermostats with O 2 sensors. Month 1 (1-12) Local Date Day 1 (1-31) Local Date "OPt" HrS (Time & Date) OPt (Options) Only available with O 2 sensor models For thermostats with temperature and humidity sensors, go to "InPt" menu. O2 DISPLAY YES NO BV.65 When set to YES, the unit will not display the time when in Operation Mode For thermostats with temperature and humidity sensors, go to "InPt" menu. O2 Setpnt 800 ppm AV.141 To display O 2 without generating an alarm, use a setpoint higher than 2000ppm or the O2 Maximum Range (highest of the 2). Appears only if using thermostats with O2 sensors. O2 ontrol Source trl ANLg BV.66 Appears only if using thermostats with Humidity sensors. DISPLAY Humidty YES NO BV.60 "PrSs" EVB Standard Page 13

14 Networkable VAV ontroller Operation Menus This menu is accessible through normal operation mode. The Mode Selector jumper (JP1) of the thermostat must be set to the RUN position (Operation Mode). Refer to Wiring on page 6. Note: Since the action buttons are different on TRL and TDU thermostat series, both buttons have been included in the instructions. Refer to the Action Buttons on Thermostat section to know and use the button as available on your thermostat. 1. Press the [ / ] and [ ] buttons simultaneously for 5 seconds. The Enter Password screen appears. 2. Enter the password within 1 minute by using the arrow keys to increase or decrease the value and the [ / ] and [ ] buttons to toggle between the digits. a. Password 372 = Temperature Offset Menu b. Password 637 = Network Settings Menu c. Password 757 = Airflow Balance Mode 3. If you enter the wrong password, the thermostat displays Eror and returns to Operation Mode. The thermostat will return to normal mode if you navigate through the entire menu and do not make any selection, or if you do not press any key for 5 minutes. The changed values will be saved automatically. Menu 372 Temperature Offset 1. Intern Temp Sensor Offset Range: 10 to 40º [50 to 104ºF] Offset: Increment: Max ± 5º 0.1º [0.2ºF] ompare the displayed temperature reading with a known value from a thermometer. To offset or calibrate the sensor, use the arrows key to set the desired temperature reading. This is useful for thermostats installed in areas where the temperature read is slightly different than the room s actual temperature. For example, a thermostat placed right under the air diffuser. If the thermostat is set to use an external temperature sensor (EtS), the thermostat displays OFF. 2. Extern Temper Sensor Offset Range: 0 to 50º [41 to 122ºF] Offset: Increment: Max ± 5º 0.1º [0.2ºF] This option appears if you ve set one of the analog inputs to EtS (External temperature sensor). When the thermostat is connected to the appropriate analog input, the display shows the temperature read by the external temperature sensor. Adjust the offset by comparing it with a known value (e.g. thermometer). If the sensor is not connected or short circuited, then the unit displays the sensor's limit. 3. Input3 Reading Range: 250mV (0") to 4000mV (1") Displays the voltage output value in mv of the pressure sensor. Does not appear for EVB14NDT4S (pressure dependent). 4. Input3 Minimum Reading Range: Default: 10mV to 180mV 60mV This setting represents the deadband of the pressure sensor in mv. For advanced users or special applications only. We recommend that you use the default setting of 60mV. Does not appear for EVB14NDT4S (pressure dependent) model. Menu 637 Network Settings If type = ba, menu contains "type", "ba" and "PYc" If type = mod, menu contains "type" and "mod" Network onfig type (Type) mod (Modbus) ba (BAnet) PYc (copy config) End (exit menu) Network hoice ba (BAnet) mod (Modbus) Modbus Auto Baud Rate No (Manual) Yes (Automatic) BAnet Auto Baud Rate No (Manual) Yes (Automatic) "BAnet Auto Baud Rate" "Modbus Auto Baud Rate" Modbus Baud Rate 57.6k (9.6k, 19.2k, 38.4, 57.6k) Modifiable only if Auto Baud Rate set to "No". Bacnet Baud Rate k (9.6k, 19.2k, 38.4, 76.8k) Modifiable only if Auto Baud Rate set to "No". Modbus omport onfig NP2s (no parity, 2 stop bits) EP1s (even parity, 1 stop bit) OP1s (odd parity, 1 stop bit) MSTP MA Address 0 (0-254) Modifiable only if all DS1 DIP switches are set to OFF Modbus Address 1 (1-246) Modifiable only if all DS1 DIP switches are set to OFF (device instance) Returns to run mode MSTP MAX Master 127 (1-127) "PYc" Exit menu and return to normal operation Start Address 0 (0-254) AV.165 End Address 0 (0-254: max=start + 63) AV.166 onfirm opy onfig No (cancel) Yes (confirm) BV.90 Returns to run mode opy onfig in (in progress) opy onfig Result Succeed AV.167 Returns to run mode *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** EVB Standard Page 14

15 Networkable VAV ontroller Menu 757 Airflow Balance Mode Pressure Independent: models EVB14NIT0S, EVB14NIT2S, and EVB14NIT4S VAV onfig Onf (configuration) SEtc (settings) bal (balancing) mot (motor) End (exit menu) Pressur Filter Time In Sec Airflow Intgral time in Min Air Flow Scale 2 sec (1-10 sec) AV min (0-60 min) AV Airflow Setting OOl HEAt AV.103 Maximum ooling Airflow 1000 (Min cool airflow to Kfactor) AV.105 Maximum Heating Airflow 1000 (Min heat airflow to Kfactor) MSV.41 AV.102 Minimum ooling Airflow 200 (0 to max cool airflow) AV.104 Minimum Heating Airflow 200 (0 to max heat airflow) "HEAt" Select Airflow KFactor 1200 AV.101 Range depends on air flow scale from previous step: (1) = (10) = (100) = "bal" "SEtc" Exit menu and return to normal operation Airflow Balance LOs (close) Min (minimum flow) ma (maximum flow) OPEn (fully opened) Motor Overide Auto (automatic) OPEn (open) LOs (close) FLOl (airflow low) FLOh (airflow high) MSV.47 MSV.37 lose Motor 130 (see note) Minimum Airflow AV (same as lose Motor) Maximum Airflow 135 (see note) Open Motor AV (same as Maximum Airflow) Returns to run mode AV.114 AV.112 Flow value depends on the actual mode of the system : Heating = heating airflow ooling = cooling airflow "mot" "mot" "mot" "mot" Adjusts the offset of the airflow reading. Offset range depends on selected air flow scale in onf menu. (1) = +/ 500 (10) = +/ 50.0 (100) = +/ 5.00 Displays the airflow based on the Kfactor. Range depends on air flow scale in onf menu:. (1) = (10) = (100) = When balancing, use only two of the four modes available ; either: lose Motor and Open Motor or Minimum Airflow and Maximum Airflow (more precise) *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** Note: Refer to EVB-Airflow Balance Instructions on Neptronic website for further information on airflow balancing function. Pressure dependent model EVB14NDT4S or other models if in pressure dependent mode VAV onfig mot (motor) End (exit menu) = mot (Motor position) is not functional on motor less models such as EVB14NDT2. Ignore Exit menu and return to normal operation Motor Overide Auto (automatic) OPEn (open) LOs (close) Reset to Factory Default Settings Returns to run mode the option. *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** This will erase all actual configurations and replace them with the factory default settings. 1. The Mode Selector jumper (JP1) of the thermostat must be set to the RUN position (Operation Mode). Refer to Wiring on page During the power up sequence of the controller and thermostat (when the firmware versions are displayed), press and hold both the and buttons. 3. The Enter Password screen appears. Enter 372 within 1 minute by using the arrow keys to increase or decrease the value and the [ / ] and buttons to toggle between the digits. 4. Use the arrow buttons to select YES and then press [ / ]. EVB Standard Page 15

16 Networkable VAV ontroller Operation Mode The Mode Selector Jumper (JP1) of the thermostat must be set to the RUN position (Operation Mode). Refer to Wiring on page 5. TRL24 O 2 reading in ppm (O 2 display option must be enabled in programming mode ) Appears if in Night Setback (NSB) or Occupancy (O) mode. Flashes if overridden by user. %RH Actual demand Room temperature Alternates between room temperature for 8 sec and then room humidity for 2 sec. (requires Humidity sensor thermostats ) Press for 5 sec. to display air flow (if using pressure sensors ) Press once to display control mode Press twice to display setpoint Press to toggle between and F Press to change mode : -Auto -Off Appears if setpoint adjustment is locked Setpoint value - ool only - Heat only Exits after 5 sec. Exits after 5 sec. Exits after 3 sec. hange setpoint value Scroll through the following values : "Airflow" * "Airflow Setpoint" * "Actual Damper Pos Percent " "Air Supply Temp" * appears only in pressure independent mode appears only if "AST" is selected for the Analog Input Signal Type TDU O2 reading in ppm (O2 display option must be enabled in programming mode ) Appears if in Night Setback (NSB) or Occupancy (O) mode. Flashes if overridden by user. Press for 5 sec. to display air flow (if using pressure sensors ) Press once to display control mode Press to toggle between and F Press twice to display setpoint Actual demand Fan icon appears in fan -powered box applications only Appears if setpoint adjustment is locked Room temperature %RH hange setpoint value Alternates between room temperature for 8 sec and then room humidity for 2 sec. (requires Humidity sensor thermostats ) Exits after 5 sec. Exits after 5 sec. Exits after 3 sec. Setpoint value Scroll through the following values : "Airflow" * "Airflow Setpoint " * "Actual Damper Pos Percent " "Air Supply Temp " * appears only in pressure independent mode appears only if "AST" is selected for the Analog Input Signal Type Press to change mode : - Auto - Off - ool only - Heat only EVB Standard Page 16

17 Power Up Networkable VAV ontroller Upon power up, the LD illuminates and all segments appear for 2 seconds. The thermostat then displays its current version of the thermostat for 2 seconds followed by the current version of the controller for 2 seconds. Pressing any key on the thermostat illuminates the LD for 4 seconds. O 2 (Thermostats with O 2 Sensors) If enabled via the configuration menu, the thermostat displays the O 2 reading on the first line above the temperature reading. If O 2 display is enabled, the time will not be displayed. Temperature Display and Setpoint If enabled in the "Display Info" menu (see Settings Menu (5 of 6) Temp, Motor, Settings and Ramps on page 12), the thermostat displays the temperature reading. If the sensor is disconnected or short circuited, then the unit displays the sensor's limit. To toggle the temperature scale between º and ºF, press the button. To display the setpoint, press the or key twice. The setpoint appears for 5 seconds. To adjust the setpoint, press the arrow keys while the temperature is displayed. If the setpoint adjustment has been locked Setpnt Locked, the lock symbol appears. Humidity If enabled in the "Options" menu (see Settings Menu (6 of 6) Network, Time and Options on page 13), the thermostat displays the temperature reading for 8 seconds and then displays the humidity reading for 2 seconds. If the sensor is disconnected or short circuited, then the unit displays the sensor's limit. Airflow and Air Supply Temperature Press and hold the [ / ] button for 5 seconds and use the arrow keys to view the airflow, airflow Setpnt", actual damper pos percent and air Supply Temp. After 5 seconds without any action, the thermostat returns to operation mode. The air supply temperature appears only if analog input AI1 or AI2 are configured with the AST option. Not available on the following pressure dependent model EVB14NDT4S. ontrol Mode To access the ontrol Mode, press the [ / ] button. The ontrol Mode appears for 5 seconds. Press the [ / ] button to scroll through the following control modes. These options can vary depending on the options selected in "Temp ontrol Mode" and "Enable OnOff ontrol Mode". Auto (Automatic ooling or Heating) OFF (if it is not disabled in Programming Mode) ooling only (on, with cooling symbol) Heating only (on, with heating symbol) Night Setback (NSB) or Occupancy Mode This function is only available if you set DI1 to nsb (Night setback contact) or Occ (occupancy mode). If the DI1 contact is triggered, the thermostat enters NSB or No Occupancy Mode (the symbol appears) and uses the NSB or O heating and cooling setpoints. If not locked, you can override the night setback or no occupancy mode for a predetermined period by pressing any of the 4 buttons. During the override period the symbol will flash. If the symbol does not flash, the override period is finished or the night setback or no occupancy override has been locked in programming mode. Set Time and Date 1. Ensure that JP1 on the thermostat is set to run. 2. Press and hold the button for 5 seconds 3. Use the arrow keys to set the desired value. Press the [ / ] button to save and got to the next step. Press the button to go to the previous step without saving. Local Time Local Time Local Date Set Time Display format 24 (24-hour format) 12 (AM/PM format) Hours 12 (0-23 or 1-12 am/pm) Minutes 00 (00-59) Year 15 (15-99) Month 1 (1-12) Local Date Day 1 (1-31) Local Date Exits and returns to RUN mode. *** To save any changes, press on TRL and on TDU *** *** To the previous step without saving, press on TRL and TDU *** EVB Standard Page 17

18 Networkable VAV ontroller Annex A: ontrol Apps Refer to Pressure & Applications Menu (1 of 6) on page 8 for more information. The available ontrol Apps vary according to the model. Description L (cool only) LHt (cool/heat) HrH (cool/heat/reheat) O 2 (O 2 ) ITOS (ITOS) FPbo (fan powered ON) FPbA (fan powered Auto) Min. Setpoint 20 (68 F) 20 (68 F) 20 (68 F) 20 (68 F) 15 (59 F) 15 (59 F) 15 (59 F) Max. Setpoint 28 (82 F) 28 (82 F) 28 (82 F) 28 (82 F) 30 (86 F) 30 (86 F) 30 (86 F) hangeover Setpnt 24 (75 F) 20 (68 F) 20 (68 F) 20 (68 F) 24 (75 F) 24 (75 F) 24 (75 F) TO1 Ramp HR1 R1 HR1 R1 OFF HR1 HR1 TO1 Signal Type On/Off On/Off On/Off On/Off On/Off On/Off On/Off TO1 lose Pos. 40% 40% 40% 40% 40% 35% 35% TO1 Open Pos. 0% 0% 0% 0% 0% 0% 0% TO2 Ramp HR1 HR1 HR1 O 2 OFF HR1 HR1 TO2 Signal Type Pulse On/Off Pulse On/Off On/Off On/Off On/Off TO2 lose Pos. 40% 40% 40% 40% 40% 70% 70% TO2 Open Pos. 0% 0% 0% 0% 0% 35% 35% TO3 Ramp HR2 R2 HR2 HR1 OFF Fan ON Fan Auto TO3 Signal Type On/Off On/Off On/Off On/Off On/Off On/Off On/Off TO3 lose Pos. 40% 40% 40% 40% 40% 40% 40% TO3 Open Pos. 0% 0% 0% 0% 0% 0% 0% TO4 Ramp HR2 HR2 HR2 HR1 OFF HR1 HR1 TO4 Signal Type Pulse On/Off Pulse On/Off On/Off On/Off On/Off TO4 lose Pos. 40% 40% 40% 40% 40% 40% 40% TO4 Open Pos. 0% 0% 0% 0% 0% 0% 0% Motor Ramp R1 Or Or Or R1 R1 Or AO1 ramp HR1 R1 HR1 R1 HR1 HR1 HR1 AO2 Ramp HR2 HR1 HR2 HR1 OFF HR2 Fan Auto AI1 Input OFF SENS SENS SENS OFF OFF SENS AI2 Input OFF OFF OFF O 2 OFF OFF OFF DI1 Input nsb.o nsb.o nsb.o Occ.o Occ.o nsb.o nsb.o Heat Prop Band 2 2 (4 F) 2 (4 F) 2 (4 F) 2 (4 F) 2 (4 F) 1 (2 F) 1 (2 F) Heat Deadband (2.6 F) 1.3 (2.6 F) 1.3 (2.6 F) 1.3 (2.6 F) 0.3 (0.6 F) 1.3 (2.6 F) 1.3 (2.6 F) ool Deadband (2.6 F) 1.3 (2.6 F) 1.3 (2.6 F) 1.3 (2.6 F) 0.3 (0.6 F) 0.3 (0.6 F) 0.3 (0.6 F) Legend Grey Text = Standard default value Bold Text = Special default value for selected application HR = Heating ramp R = ooling ramp Or = hangeover ramp SENS = hangeover temperature sensor Fan ON = Fan powered box in continuous mode Fan Auto = Fan powered box in automatic mode (follows demand) nsb.o = Night Setback (normally open) Occ.o = Occupancy mode (normally open) TO AO AI DI = TRIA output = Analog output = Analog input = Digital input EVB Standard Page 18

19 Notes

20 Recycling at end of life: please return this product to your Neptronic local distributor for recycling. If you need to find the nearest Neptronic authorized distributor, please consult Lebeau blvd, Montreal, Qc, H4N 1R6, anada Toll free in North America: Tel.: (514) Fax: (514) ustomer service fax: (514) Monday to Friday: 8:00am to 5:00pm (Eastern time)