I-WARM Heating Mats. Contents
|
|
- Meagan Strickland
- 6 years ago
- Views:
Transcription
1
2 Contents 1. General System application System delivery kit Heating mats Thermostats Preparation for Installation Location of heating mat Electric wiring and location of thermostat Heating System Installation Turning the System on and Operation Hints and Notes Your Safety Warranty Certificate Appendix Expansion joints Thermal insulation I-WARM heating mat specifications Instructions on preparation and application of tile adhesive for installation of underfloor heating mats
3 Thank you for choosing ultra-thin I-WARM underfloor mat heating system manufactured by «Special Systems and Technologies» Company. We are happy to offer you this product which will meet your expectations and bring comfort to your home. 1 General This installation manual contains instructions for installation and connection of I-WARM heating system. Please, carefully read this manual before commencing installation. Make sure that chosen system is suitable for your premise and the size of the area to be covered. Please note that incorrect installation could damage the system, if all instructions are followed, no problems should arise. It is strongly recommended to use a qualified installer. 2 System application Ultra-thin I-WARM underfloor heating system is an electrical cable system on the basis of heating mat for heat retaining creation. It doesn't require the installation of a screed, because it can be easily laid into thin undertile adhesive layer. It is applicable for all types of premises and can be easily installed both on a new surface or on the existing floor in case of repair works, especially when it is highly important to keep low thickness of floor construction or in the premises with low ceilings. Ultra-thin I-WARM underfloor heating system is used as comfort heating system in the premises with main heating system installed. 3 System delivery kit I-WARM underfloor heating kit includes: single-conductor MH pp-ss heating mat, where pp stands for rated power in Watts, and ss stands for mat square, m 2, or double-conductor MHH pp-ss heating mat where pp stands for rated power in Watts, and ss stands for mat square, m 2 ; thermostat with temperature probe; corrugated tube for temperature probe placement (1,5m long). Technical descriptions, wiring diagrams and warranty liabilities of heating mats and thermostats are given in passports. 2
4 I WARM Heating Mats double conductor heating mat thermostat * single conductor heating mat temperature probe corrugated tube * is stocked with one of the thermostats given at Paragraph Heating mats MH single conductor heating mat (I WARM Mini) Single conductor heating mat is made of a shielded one-core cable, fixed on the fiber mesh. Both ends of the heat ing section are fitted up with installation wires and reliable coupling which passed factory testing. To differentiate mats according to space and power output types various cable sheath colors and markings are used. Specifications of heating mats are given in the Appendix (please, refer to paragraph 10.3). MH heating mat is manufactured and tested in full accordance with IEC (Inter national Electrotechnical Commission) Global Quality Standards. High reliability of mats is ensured by ultra-thin screened cables with diminished effect (linear power), which are fixed on the mesh with constant wire spacings. Rated linear power of cables used in mats is lower than in standard cables used for under floor heating but power output of each square meter of heating mat is about 140 W that ensures highly uniform and efficient heating. warm.com 3
5 Сonnection of MH heating mat MH MN heating mat Coupling muff Installation wire (cold lead) Braided shield Thermostat control circuit Temperature probe Thermostat terminal blocks Power supply 230/240 VAC Grounding loop or Neutral conductor Thanks to the cable fixation on the mesh there is no need to adjust the wire spacings and to fix the cable on the floor surface which can by chance lead to the damage of the wire during the process of installation. I-WARM mats are produced out of high-quality materials provided by world leading plastic manufacturers. Reliability and safety of heating mats is approved by the Russian Certificate of Conformance, Fire-safety certificate and Hygiene Certificate. MH heating mat consists of heating cable, two couplings and installation wires. Heating conductor and screen are securely connected with two installation wires, which are designed to connect heating section to thermostat and protective earthing. For correct MH mat connection, please, pay attention to coloring of installation wires. White installation wires are connected to heating conductor and are to be connected to the thermostat. Braided shield is to be connected to the earth loop of the building (or to zero wire of power network). MHH double-conductor heating mat (I-WARM Tropics) Double-conductor heating mat is made of a shielded twin-core cable, fixed on the fiber mesh. One end of the heating section are fitted up with cold lead and reliable coupling which passed factory testing and sealing end. To differentiate mats according to space and power output types various cable sheath colors and markings are used. Specifications of heating mats are given in the Appendix (please, refer to paragraph 10.3). 4
6 Сonnection of MHH heating mat MHH MNN heating mat Coupling muff Installation wire (cold lead) Termination muff Thermostat control circuit Temperature probe Thermostat terminal blocks Power supply 230/240 VAC Grounding loop or Neutral conductor MHH heating mat is manufactured and tested in full accordance with IEC (International Electrotechnical Commission) Global Quality Standards. High reliability of mats is ensured by ultra-thin screened cables with diminished effect (linear power), which are fixed on the mesh with constant wire spacings. Rated linear power of cables used in mats is lower than in standard cables used for underfloor heating but power output of each square meter of heating mat is about 140 W that ensures highly uniform and efficient heating. Thanks to the cable fixation on the mesh there is no need to adjust the wire spacings and to fix the cable on the floor surface which can by chance lead to the damage of the wire during the process of installation. I-WARM mats are produced out of high-quality materials provided by world leading plastic manufacturers. Reliability and safety of heating mats is approved by the Russian Certificate of Conformance, Fire-safety certificate and Hygiene Certificate. MHH heating mat consists of double-conductor heating cable, one coupling, installation wires and sealing end. Heating conductor and screen are reliably connected with two installation wires, which are designed to connect heating section to thermostat and protective earthing. For correct MHH mat connection, please, pay attention to coloring of cold leads. Blue and brown installation wires are connected with heating conductor and are to be connected to the thermostat. Ground bus is to be connected to the earth loop of the building (or to zero wire of power network). 5
7 3.2 Thermostats Thermostat is an energy saving device which automatically turns the heating system on and off. It applies voltage to heating section only when it is necessary to maintain desired temperature of the system for creating comfortable ambient of your accommodation. Using programmable thermostat you can set the device to maintain comfort temperature during twenty-four hours or a week period. All SST thermostats are stocked with temperature probe heating resistor installed in the floor. Roomstat 110 The most popular thermostat model. It has modern design, lower weight and smaller dimensions. It has a separate power switch. The thermostat is supplied with LED indication of the heating system «ON» state. The device can be placed in multisocket wall mounted frame. Provides energy saving up to 30%. Roomstat thermostat has a maximum load current of 16 amps. I WARM 710 Room thermostat with two temperature sensors remote floor temperature sensor and built-in air temperature sensor. It is flush mounted. This thermostat is designed for constant maintenance of the preset temperature using floor temperature sensor. Large-screen backlit graphical display, three control buttons. User-friendly «intuitive» «one-touch» interface. Indication of current floor temperature, set temperature, ON/OFF heater condition. Self-diagnostic of heating system with warning caption output. An additional mode allows to display ambient air temperature (at that temperature control is still based on floor temperature sensor). 6
8 Additional heating control mode without temperature monitoring time unit is equal to one hour. ON/OFF time is set by user in percentage rating. The user sets the percentage 10% to 90%. Allows precise power control. I WARM 710 thermostat has a maximum load current of 16 amps. I WARM 720 Room thermostat with remote floor temperature sensor. It is flush mounted. The device allows to decrease significantly energy consumption of warm floor by maintaining comfort temperature only in the preset time intervals when it is really required by the customer. Large-screen backlit graphical display, three control buttons. User-friendly «intuitive» «one touch» interface. The built-in menu allows to control all functions of the device. Multimode thermostat with built-in real-time block and calendar. Built-in economizer. The device stores and keeps in memory all the information about the heating system that allows customer to control his expenditures not to the expense of comfort. «Intelligent» software allows to determine parameters of heat processes in the premise. The user can only settle time intervals when he needs heating and the device makes the rest by itself. The additional display features: clock, calendar. The following temperature maintenance modes can be realized: а) Constant comfort temperature maintenance. b) Daily comfort maintenance schedule. At that daily cycle of comfort temperature distribution is realized. The user sets time intervals of the day when he requires warm floor. The device adjusts itself to the premise: determines the existing heat properties and defines by itself the time when the heating system should «turn ON» to obtain the comfort temperature exactly at the set time. All the rest time the heating system is turned OFF saving the energy. This program repeats on a daily basis. c) Weekly comfort temperature maintenance schedule. Weekly temperature distribution cycle. It is similar to «daily» option but you program seven days independently and this cycle repeats each week. I WARM 720 thermostat has a maximum load current of 16 amps. 7
9 I WARM 730 Room thermostat with 2 remote floor temperature sensors and two zones control opportunity. It is flush mounted. This model maintains the set temperature in accordance with a floor temperature sensor. Large-screen backlit graphical display, three control buttons. User-friendly «intuitive» «one touch» interface. Indication of current floor temperature, set temperature, ON/OFF heater condition. Self-diagnostic of heating system with warning caption output. Additional heating control mode without temperature monitoring during each hour. ON/OFF time is set by user in percentage rating. The user sets the percentage 10% to 90%. Allows precise power control. I WARM 710 thermostat has a maximum load current of 2х8 amps. PT320 РТ320 thermostat for installation in control cabinets on standard DIN-rail. Temperature setting regulator is fed out under slot. It is used when the power of I-WARM heating system exceeds rated value of built-in relay (3 kw). For example if some premises with the same temperature conditions are heated or one large premise is heated by several heating sections. The thermostat controls circuit breakers rated at high current to which groups of heating sections are connected. PT320 thermostat has a maximum direct load current of 16 amps. * If necessary PT320 thermostat can be fitted up with air temperature sensor instead of floor temperature sensor. Safety and reliability of thermostats is approved by the Russian Certificate of Conformance and Hygiene Certificate. 8
10 4 Before the installation I-WARM Heating Mats Before I-WARM system installations please, make sure that you chose the system suitable for your premise and desired type of heating (main or comfort heating). 4.1 Heating mat placement It is recommend to lay heating sections on the subfloor area free from fixed furniture. Place heating mats in the usable area: where you walk, where heat radiation is effective. To fit mat to the heated area configuration it is necessary to cut mesh into fragments. When cutting take care not to cut or damage the heating cable. Never allow strips of mesh to overlap. Never use one and the same mat for heating different types of premises (e.g. bathroom, hallway or kitchen). It is not recommended to use the same mat for heating premises with different floor constructions. For this purpose independent mats should be installed along with the thermostats. If it is necessary to heat balcony, terrace, interior garden, premises with many windows, open doorways, archways, premises with ceilings over 4 meter high, please, consult our manager who will offer you suitable system to heat the premise required. Heating mat placement example: 1. Heating area size estimation. Estimate heating area size and pick up adequate heating mat. Adjust mat to the heating area configuration. 2. First mat mesh cutting mat turn. 4. Second mat mesh cutting. 9
11 mat flip. 6. Heating mat after installation. Please, make sure that an existing in your premise electrical wiring can power I-WARM system. Please refer to paragraph 10.3 of the present instruction to see the amperage load for I-WARM heating systems. Take into consideration additional electrical appliances which can be energized by the same circuit. Also specify amperage load of your safety devices. 4.2 Electrical wiring and thermostat placement According to Electric Installation Code (edition of 2001) standard electrical wiring withstands the following currents and appropriate power loads (table 1): It is recommended to use a separate circuit and separate safety device to power I-WARM heating systems with power over 2kW. I-WARM systems are to be connected via Ground Fault Circuit Interrupter (GFCI) which actuating rated current doesn't exceed 30 ma. This is a small device mounted on the panelboard which controls safety of your equipment thermal insulation. When mat is installed in damp premises (bathrooms, saunas, swimming pools), heating mat screen must be connected to earthing lead of supply network. To this wire must be connected all available metal parts: metal shower trays, metal frames of shower cabins, etc. Conductor material Copper Aluminium Таble 1 Cross Max. load section, current mm 2 A, Max. total load power kw, 2 x x x x x Choose thermostat location. It should be installed in the most convenient place so it will not interfere with furniture disposal. Thermostats controlling heating in damp premises (bathrooms, toilets, saunas, swimming pools) must be installed outside of such premises 10
12 5 I-WARM system installation Using this Manual you can install I-WARM heating system by yourself. We strongly recommend to entrust connection and powering to a qualified electrician. High quality installation and connection of the system ensuring its warranty period can be performed by skilled specialists. Remember that heating system durability is 99% dependent upon its installation quality. Here you will find description and illustration of ultra-thin heating mat installation process. If you need to heat a non - standard premise, please consult our manager. Step by step I-WARM heating system installation: 1. Prepare the space on the wall for thermostat mounting. 2. Chisel out channels for power supply wires, mat cold leads and temperature sensor in the wall. 3. Chisel out 20x20mm long channel in the subfloor for floor sensor with connection wire placed in the corrugated tube. 4. Subfloor preparation: the floor should be even, secure, flex-free, with appropriate bearing capacity. The surface must be dry, clean and free of grease, dust and sharp pieces. 5. Place temperature sensor into the tube, which is included in the I-WARM heating kit. The sensor must be placed inside the tube close to its end. Its connecting wire must be exposed from the opposite end of the tube. The end of the tube with the sensor must be sealed to avoid ingress of cement mortar inside. Place the tube with sensor in the chiseled channel and lead to the thermostat or to the terminal box. Tube bending radius must be 5cm minimum. When corrugated tube is affixed to the wall and the floor, make sure that the sensor floats inside the tube. For this partially pull out and then insert back sensor connection wire. This installation method allows sensor replacement without removing flooring material. Attention: The tube end with sensor connection wire should ends at terminal box or thermostat, otherwise it will be impossible to replace sensor without removing floor covering. 11
13 6. Fill in chiseled channels with tile adhesive or grout. 7. Mark out area on the subfloor where the sensor will be fitted. 10. For single-conductor mat it is necessary to put cold leads to the thermostat via channels chiseled in the wall. Make sure there are no wire breakoffs. To check the heating mat and temperature sensor was not damaged during the installation resistance reading of heating mat and temperature sensor should be taken. This reading should conform to their passport data. 8. It is recommended to prime the subfloor with deepened grounding solution. Intensive absorbing surfaces should be primed twice. Let the surface get dry. МH 9. Lay heating mat with mesh adhesive downside on the subfloor. Make sure that floor temperature sensor is centered between two heater wires. For double-conductor mat it is necessary to put cold lead to the thermostat via channel chiseled in the wall. Make sure there are no wire breakoffs. To check the heating mat and temperature sensor was not damaged during the installation resistance reading of heating mat and temperature sensor should be taken. This reading should conform to their passport data. 11. Sketch on the premise plan the diagram of heating mat, couplings and temperature sensor location. 12
14 heating mat, temperature sensor connection wires in corrugated tube to the thermostat. МHH 12. Pour tile adhesive solution onto the mat leveling the solution from 5 8 mm and let it get dry according to the manual of preparation and application of tile adhesive used. We recommend using tile adhesive for underfloor heating systems. Its preparation and application instructions are given in paragraph When tile adhesive is dry it is necessary to check whether heating mat or temperature sensor was damaged during installation, resistance reading of heating mat and temperature sensor should be taken. This reading should conform to their passport data. 14. According to Technical Certificates of mat and thermostat connect thermostat to the heating mat, and to temperature sensor; connect electric power to the thermostat; perform earthing. 15. Fill in with tile adhesive channels chiseled in the wall which leads connection wires, earth circuit, cold leads of the 16. Lay ceramic tile using new prepared adhesive solution. Maximum thermal resistance between heating mat and the premise produced by adhesive layer and ceramic tile should not exceed 0.06 m 2 K/W. Ceramic tile covering thickness shall be 5 mm minimum. 17. When tile adhesive solution is fully dry I-WARM ultra-thin underfloor system is ready for operation. Turn it on following instructions of thermostat manual. Drying tile adhesive solution time is determined by instruction manual of tile adhesive used. Tiling directly onto the heating mat is possible. Be careful not to damage the heating cable. Adhesive layer thickness shall be 8 mm minimum. Heating mat shall be installed minimum 100 mm away from other heating appliances, e.g. risers and tubes of water heating system. 13
15 6 System switching and operation I-WARM underfloor heating system can be turned on when tile adhesive is fully dry. Switch the thermostat on and set the desired level of heating, using instructions of its Technical Certificate. During the first turning on of underfloor heating system you can set the maximum heating level. It will accelerate floor heating. When the temperature gets to comfort level, reduce heating level as desired. When the system is turned on for the first time, the «warm floor» feeling will appear in some period of time. Mainly it concerns new build unheated premises. Please do not worry and let the system heat your premise. Bear in mind that I-WARM underfloor heating system refers to comfortable heating type, it might not have enough power to heat cold premise when basic heating system is off. 7 Hints and notes Due to automatic temperature regulation I-WARM system consumes exactly as much energy as it is necessary to maintain comfort level of heating. Thermostats installed in each room control heating independently that allows energy saving. I WARM 720 is a programmable thermostat which especially allows energy saving for it automatically reduces or turns off heating when it is not necessary. The thermostat is more profitable in case of double-rate payment. If your premise stays empty in the cold season it is recommended not to turn off the system completely setting the thermostat on the minimal level. In this case the power consumption will be minimal and the room will not be chilled completely so you could heat it quickly upon return. Correct choice of I-WARM underfloor heating system will allow you to reduce heating costs up to 50%. Heating mat must be placed minimum 30mm away from walls, fixed furniture or other items preventing effective heat radiation. During heating mat installation avoid direct contact with thermal insulation if it is of corrosive, hygroscopic, or flammable type. During the installation heating mat should not be exposed to oil, lubricant or similar substance influence. Braided shield of the mat cold lead must be securely connected to earthing terminal in the junction box or to adequate thermostat terminal. To avoid mechanical damage of the heating mat perform installation wearing soft elastic sole shoes or cover the mat surface with plywood boards or other material preventing heating cable damage when walking on it. Minimum mat installation temperature is -5 C. 14
16 8 Your safety Do not change mat configuration made by manufacturer apart from mesh cutting during installation. Do not replace cold leads breaking sealed coupling connections made by manufacturer. Do not alter thermostat design. Never turn on rolled up heating mats even for a short period of time. Never plug heating mats to power supply with voltage different from operating voltage stipulated in Technical Certificate, marking or packaging. Never perform thermostat installation and repairing with ON power supply. Use a qualified installer. Never use heating mats without minimum tile adhesive layer which covers heating cable completely. Pour adhesive solution onto heating mat leveling it evenly along the total surface. Avoid air gaps near heating cable which prevent heat radiation. Floor sensor installation shall be done in the way which allows its further replacement without removing flooring material (See paragraph 5). Do not cover floor surface where heating mat is installed with any thermal isolation materials (carpets, blankets et.c.). Do not hammer nails, dowels or screw into the floor surface where heating mat is installed. Violation of any enlisted requirements will invalidate your warranty. 15
17 9 Warranty Certificate I-WARM 16-YEAR WARRANTY I-WARM 16-YEAR WARRANTY DOES NOT EXTEND TO THERMOSTATS, WHICH ARE COVERED BY A ONE-YEAR GUARAN- TEE FROM THE DATE OF ORIGINAL PUR- CHASE. GOVERNING LAW. Unless otherwise governed by applicable state law, this warranty shall be interpreted and enforced in accordance with the laws of Russian Federation. This 16-Year I-WARM applies: 1. Only to the original homeowner(s) from the date of purchase. 2. Only for the duration of the Lifetime of the floor covering under which it was originally installed if the purchaser of the heater remains the owner of the residence in which it was installed. If the original purchaser sells such residence, the warranty will transfer and continue for the duration of the16 years from date of purchase. 3. Only if the heater has been grounded and protected by a GROUND FAULT CIRCUIT INTERRUPTOR (GFCI) at all times. COVERAGE 1) The warranty period begins on the date of purchase. 2) I-WARM underfloor system is guaranteed by SST LLC to be free from defects in materials and workmanship under normal use and maintenance for sixteen (16) years, provided the Product is installed in accordance with the accompanying I-WARM installation manual, any special written design or installation guidelines by SST LLC for a particular project, the National Electrical Code (NEC) and all applicable local building and electrical codes. 16 3) Provided I-WARM heaters are installed under ceramic tile, marble and natural stone surfaces. 4) During the period of Warranty, I-WARM will arrange for the heater to be repaired or (at its discretion) have parts replaced free of charge. The costs of repair or replacements are your only remedy under this Warranty. Such cost does not extend to any cost other than direct cost of repair or replacement by I-WARM and does not extend to costs of relaying, replacing or repairing any floor covering or floor. 5) If SST LLC determines the repair of the product is not feasible; we will replace the product with equal or similar features and functionality at SST LLC sole discretion. SST LLC MAXIMUM LIABILITY IS LIM- ITED TO THE ORIGINAL PURCHASE PRICE OF THE HEATER MULTIPLIED BY THE PERCENTAGE OF THE WARRANTY PERIOD REMAINING. EXCLUSIONS SST LLC shall in no event be liable for incidental or consequential damages, including but not limited to extra utility expenses or damages to property. This Warranty is null and void if: 1) The floor covering over the heater(s) is damaged, lifted, replaced, repaired or covered with subsequent layers of flooring. 2) The heater fails due to damage caused during installation or tiling, unless damage is caused directly by an employee of SST LLC. It is therefore essential to check that the heater is working (as specified in the installation manual) prior to tiling. 3) Damage as a result of floods, fires, winds, lightning, accidents, corrosive
18 atmosphere or other conditions beyond the control of SST LLC. 4) Use of components or accessories not compatible with I-WARM heaters. 5) Parts not supplied or designated by SST LLC. 6) Damage or repair required as a result of any improper use, maintenance, operation or servicing. 7) Failure to start due to interruption and/or inadequate electrical service. 8) Any damage caused by frozen or broken water pipes in the event of equipment failure. 9) Changes in the appearance of the product that does not affect its performance. If I-WARM is required to inspect or repair any defects caused by any exclusions referenced above, all work will be fully chargeable at SST LLC inspection and repair rates then in effect. SST LLC DISCLAIMS ANY WARRANTY NOT PROVIDED HEREIN, INCLUDING ANY IMPLIED WARRANTY OF THE MER- CHANTABLE OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. SST LLC FURTHER DISCLAIMS ANY RESPONSIBILITY FOR SPECIAL, INDI- RECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WAR- RANTIES THAT EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR REPRESENTATIVE OF SST LLC HAS ANY AUTHORITY TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTEN- SION OR MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER. DUE TO DIFFERENCES IN BUILDING AND FLOOR INSULATION, CLIMATE AND FLOOR COVERINGS, SST LLC MAKES NO REPRESENTATION THAT THE FLOOR TEMPERATURE WILL ACHIEVE ANY PAR- TICULAR TEMPERATURE OR TEMPERA- TURE RISE. TERMS AND CONDITIONS Shipping Discrepancies: Incoming materials should be inventoried for completeness and for possible shipping damage. Any visible damages or shortages must be noted prior to accepting the material. Any discrepancy concerning type or quantity of material shipped, must be brought to the attention of your I-WARM reseller within 15 days of the shipping date entered on the packing slip for the order. Miscellaneous: The terms of this Limited Warranty are exclusive and supercede any other warranty or terms and conditions relating to the subject matter whether included in a purchase order for this product or in any other document or statement. 17
19 WARRANTY CERTIFICATE Full Name Street City Zip Code Telephone# E- Mail Purchased from City Installer name Date of Purchase I-WARM system is used as COMFORT heating system. for heating of (type of the premise) total area sq.m area size to be covered sq.m I-WARM heating kit comes complete with: Heating mat (type) Heating mat (type) Thermostat Thermostat (type) Corrugated tube m Manager (signature) Sales office stamp Customer (signature) The installation was performed by Date 200 (signature) 18
20 The plan of the premise I-WARM Heating Mats The plan of the premise with location indication of thermostat, heating mat, couplings and end muffs, and floor temperature sensor. Remember to attach a label to the distribution board with sketched diagram of the wire layout for future reference, which should be kept with a manual for future reference. Heating mat Temperature sensor tube Legend Thermostat Coupling Temperature sensor End muff Mat R... Ω Gage R... Ω 19
21 10 Appendix 10.1 Expansion joints Do not install heating cable through an expansion joint. Heating cable should be installed right up to the joint, if necessary, but do not bridge the joint subfloor 2 expansion joint 3, 4 heating mats Thermal insulation Taking into account that the design of I-WARM underfloor heating system does not imply arrangement of cement-sand layer 3 5 cm thick, direct laying of the heating mat on thermal insulation is not recommended, because in this case thin layer of tile adhesive covering the mat can crack with heat. The base on which the mat is installed must be solid and be of sufficient bearing capacity. 20
22 10.3 Specification of I-WARM heating mats Type MH-160-1,1 MH-215-1,5 MH-265-1,9 MH-360-2,5 MH-470-3,1 MH-570-3,9 MH-660-4,4 MH-800-5,3 MH-980-6,6 MH ,5 MH ,5 MH ,0 MH ,2 MH ,7 MH ,2 Power, W 230/240 V 160/ / / / / / / / / / / / / / /2650 Area, m 2 1,1 1,5 1,9 2,5 3,1 3,9 4,4 5,3 6,6 7,5 8,5 10,0 12,2 13,7 16,2 Type MHH-135-1,0 MHH-220-1,6 MHH-300-2,1 MHH-380-2,7 MHH-470-3,4 MHH-545-3,8 MHH-650-4,8 MHH-815-5,7 MHH-930-6,8 MHH ,8 MHH ,0 MHH ,0 MHH ,7 MHH ,0 Power, W 230/240 V 135/ / / / / / / / / / / / / /2175 Area, m 2 1,0 1,6 2,1 2,7 3,4 3,8 4,8 5,7 6,8 7,8 9,0 11,0 12,7 14,0 21
23 10.4 Recommendations on preparation and application of tile adhesive for underfloor heating mats Subfloor preparation Make sure the floor is clean, secure and free from dust, grease and et.c. Fill in all cracks and holes in the floor surface. It is necessary to prime clean surface using brush or roller. Minimum subfloor temperature should be +5 С. Underfloor Heating System Construction Place heating mat and temperature sensor on the prepared surface according to the Underfloor heating system Instruction Manual. Adhesive solution preparation Pour dry mixture to the vessel with clean water according to the requirements of dry mixture manufacturer and mix it thoroughly using construction mixer until smooth. Let it cure and mix it again according to the requirements of dry mixture manufacturer. Do not add other components to the mixture! Unclean vessels and tools reduce material time of use! Underfloor heating system grouting First option (Tiling of subfloor with heating mat installed) Apply in small portions prepared adhesive solution to the subfloor with laid heating mat spreading solution with a tipped trowel. Lay the tile on the spot and sunk it into the adhesive with a slight touch. Be careful not to damage heating cable. Tile adhesive shall cover heating mat fully and be in tight, air-void free contact with tile surface. Tile shall not touch heating cable or lean on it. Tile adhesive layer thickness shall be 8 10mm. Tile Tile adhesive Heating mat Subfloor Matting underfloor heating system 22
24 Second option (Primary protective layer construction) Pour self-leveling floor onto the mat to a thickness of 5 8 mm according to the instruction manual for preparation of this modified adhesive solution. This interlayer shall cover the mat completely with no air voids, heating mat shall not float up, heating cable shall be buried in this layer. When covering layer cures (curing time should be specified by dry mixture manufacturer) prime the foundation and then perform tiling using prepared tile adhesive solution to a thickness of 5 10mm. Important Notes During application and curing of tile adhesive, ambient temperature shall be from +5 C to +25 C. Make sure there are no draughts in the working room. Underfloor heating system can be turned on only when tile adhesive is fully cured. 23
25 Notes 24
26
Underfloor Heating Cable Installation Manual
Affordable Underfloor Heating Underfloor Heating Cable Installation Manual Technical Helpline 0845 034 8272 www.sunstone.co.uk SunStone Wire Manual V3.1.indd 1 09/01/2015 14:00:49 BEFORE YOU BEGIN INSTALLATION...
More informationUnderwood Heater Installation Manual
Underwood Heater Installation Manual Contents Important Safeguards and Warnings... 3 1 General Information... 3 1.1 Use of the Manual... 3 1.2 Safety Guidelines... 3 1.3 Remember to measure resistance...
More informationUnderfloor Heating Mat Installation Manual
Affordable Underfloor Heating Underfloor Heating Mat Installation Manual Technical Helpline 0845 034 8272 www.sunstone.co.uk 1 SunStone Mat Manual V3.1.indd 1 09/01/2015 13:58:26 DO S & DON TS ENSURE CORRECT
More informationHEATING USER GUIDE. Philex Support Line: Monday to Friday 9.00am to 5.00pm (Local rate - UK only)
HEATING Underfloor Heating Kit USER GUIDE WARNING: Before installation make sure you have selected the right sized mat - you cannot cut the cable to make it shorter - slightly too small is better than
More informationamuheat Cable Mat floor heating systems Installation Manual CM02-12
amuheat floor heating systems Cable Mat Installation Manual CM02-12 Table of Contents Introduction 1 2 Cable Mat Important Installation Guidelines Tools & Materials Needed for Installation Kit Contents
More informationUnderfloor Heating Inscreed Cable System
The world s best-selling floor heating brand Installation Manual: Underfloor Heating Inscreed Cable System TECHNICAL HELPLINE 085 5 2288 IMPORTANT Read this manual before attempting to install your inscreed
More informationIMPORTANT NOTES. Electric Underfloor Heating Mats For use with Touchsceen underfloor heating Thermostat
For any assistance or further information, go online at bathstore.com Electric Underfloor Heating Mats For use with Touchsceen underfloor heating Thermostat - 61000012339 Model Dimensions Area Covered
More informationFoil Heaters. Installation Manual: TECHNICAL HELPLINE
Installation Manual: Foil Heaters TECHNICAL HELPLINE 0345-345-2288 Complete and submit the warranty form online at www.warmup.co.uk IMPORTANT Read this manual before attempting to install your foil heater.
More informationElectric Floor Warming Systems Installation and Operation Instructions. Mat Heating Systems and Cable Heating Systems. UL Listed for USA and Canada
Electric Floor Warming Systems Installation and Operation Instructions Mat Heating Systems and Cable Heating Systems UL Listed for USA and Canada Thank you for your purchase of a Warming Systems electric
More informationQuickNet System Installation Manual Manuel d installation du système QuickNet Manual de instalación del sistema QuickNet
QuickNet System Manual Manuel d installation du système QuickNet Manual de instalación del sistema QuickNet Floor heating system Système de chauffage par le plancher Sistema de calefacción de pisos Table
More informationInstallation Manual Loose cable underfloor heating. A large print version can be downloaded from our website. www. underfloorheatinghq.co.
English Installation Manual Loose cable underfloor heating A large print version can be downloaded from our website www. underfloorheatinghq.co.uk Phone: 0800 328 4980 E-mail: enquiries@underfloorheatinghq.co.uk
More informationCoziMat. 1. Introduction and Brief Description COZIMAT INSTALLATION INSTRUCTIONS & SAFETY REQUIREMENTS
CoziMat 1. Introduction and Brief Description The CoziMat underfloor heating mat is designed for underfloor heating of rooms where the floor thickness needs to be kept to a minimum. CoziMat underfloor
More informationFloorHeat Installation Manual
FloorHeat Installation Manual Transforming frosty floor surfaces into radiant warmth Transforming frosty floor surfaces into radiant warmth Contents Important Instructions!... 3 Safety Instructions:...
More informationElectric Warm-Stretch under floor heating
Electric Warm-Stretch under floor heating bath store Installation Manual Please read these instructions before you start your installation. Any damage to the system due to incorrect installation will invalidate
More informationInstallation Manual. Frost Protection Cable. Warmup Ireland Web: Telephone:
Installation Manual Frost Protection Cable Warmup Ireland Web: www.warmup.ie Email: ie@warmup.com Telephone: 1 800 937 429 TECHNICAL HELPLINE 0845 345 2288 IMPORTANT Read this manual before attempting
More informationClassic Mats Installation Manual
Classic Mats Installation Manual 1 Classic Mats WarmTouch Classic Mats are the ideal Electric floor warming systems, designed by DomoTecK, for installation under tile, stone or marble. WarmTouch Classic
More informationLIFETIME. INSTALLATION MANUAL emat Pro 100w/150w/200w WARRANTY
INSTALLATION MANUAL emat Pro 100w/150w/200w LIFETIME WARRANTY Before you begin installing, read through these instructions carefully and check that you have all the components required. 01473 276677 www.elementsunderfloorheating.co.uk
More informationModel Dimensions Coverage 230v 230Vac. Pack Contents. Measuring Up
Installation and Operating Instructions Electric tile-warming system Model Dimensions Coverage Wattage @ 230v Amps@ 230Vac RTS1M 2.0m x 0.5m 1.0m 2 160W 0.70A RTS1.5M 3.0m x 0.5m 1.5m 2 240W 1.04A RTS2M
More informationINSTRUCTION. Danfoss heating cable mats type 100/150 Danfoss heating cable mats for thin floors. Danfoss heating cable mat type 100/150
INSTRUCTION GB Danfoss heating cable mats type 100/150 Danfoss heating cable mats for thin floors NB! Read page 2 before installing the product if you intend to connect 2 mats to the same thermostat Danfoss
More informationIntroduction. Please read the following instructions carefully before commencing installation.
Introduction Please read the following instructions carefully before commencing installation. Installation involves simple processes. These are explained step by step in the following pages. Should you
More informationInstallation Instruction
GB/DAS Installation Instruction Devimat DTIF 100/150 Heating cable mats for thin floors NB! Read page 3 before installing the product if you intend to connect 2 mats to the same thermostat 1 Devimat 100/150
More informationContact Details. Please note that some of the contact details on this PDF document may not be current.
Contact Details Please note that some of the contact details on this PDF document may not be current. Please use the following details if you need to contact us: Telephone: 0844 879 3588 Email: customer.services@gdcgroup.co.uk
More informationELEKTRA RadiantFloor Heating
www.elektra.eu ELEKTRA RadiantFloor Heating single-side powered MD Heating Mats Installation manual ELEKTRA Heating Mats For the proper installation and operation of the ELEKTRA radiant floor heating system,
More informationUndertile Heating Mat. Instructions. CORGI Underfloor Heating - Quality, Flexibility, Safety 1
Undertile Heating Mat Instructions CORGI Underfloor Heating - Quality, Flexibility, Safety 1 It is vital that you read through these instructions fully before installing your CORGI undertile heating mat.
More informationAlways make sure to check the heating film before, during, and after installation of the floor covering.
Installation of floor heating film for ceramic tiles, granite and other stone or composite flooring Read through this entire manual before starting installation. All electrical connections must be made
More informationToll Free:
1 ProLine s electric radiant floor heating system is one of the most popular and durable floor heating solutions on the market. Available pre-spaced in mats with an adhesive backing or on the spool, the
More informationWarm Feet For Uncoupling Membrane Pour membrane de désolidarisation. Installation Guide Floor Heating Cable
Warm Feet For Uncoupling Membrane Pour membrane de désolidarisation Installation Guide Floor Heating Cable 119A Sir Wilfrid Laurier Saint-Basile-le-Grand, (Québec), J3N 1M2 Tel: 1-450-482-1919 Toll Free:
More informationInstallation Manual. Electric Underfloor Heating. heatingthroughinnovation.
Installation Manual Electric Underfloor Heating heatingthroughinnovation. 02 Electric Underfloor Heating Contents 1.0 General Information 03 2.0 Preparation 04 3.0 Installation 05 4.0 Measuring Values
More informationemat Pro 100/150/200 Installation Manual
emat Pro 100/150/200 Installation Manual www.electricunderfloorheating.co.uk Before you begin installing read through these instructions carefully and check that you have all the components required. Introduction
More informationTECHNICAL CERTIFICATE USER MANUAL THERMOSTAT TP years warranty
TECHNICAL CERTIFICATE USER MANUAL THERMOSTAT TP510 3 years warranty TABLE OF CONTENT Application 4 Controls and indication 4 Adjustment and operation 5 Switch on / switch off the thermostat 5 Adjustment
More informationInstallation And User Instructions GB/IRE. Devimat Warm Floor System Installation Instructions User Guide Trouble Shooter
GB/IRE Installation And User Instructions Devimat Warm Floor System Installation Instructions User Guide Trouble Shooter Please retain this booklet for homeowners future reference. For Devireg 55 setup
More informationUponor Comfort E AL-Foil Mat
Uponor Comfort E AL-Foil Mat Contents Important notes on the intended use, safety and warranty...3 Intended use...3 Uponor Declaration of Warranty...3 System description...4 Floor construction...4 Technical
More informationInstallation Guide. Heating cables. Thin concrete (< 3 cm) Intelligent solutions with lasting effect. Visit DEVI.com
Installation Guide Heating cables Thin concrete (< 3 cm) Intelligent solutions with lasting effect Visit DEVI.com Table of contents 1 Introduction.................... 2 1.1 Safety Instructions...............2
More informationInstallation And User Instructions
GB Installation And User Instructions Devimat Warm Floor System Installation Instructions User Guide Trouble Shooter 1 Existing Floor Maximum load per m 2 Wooden Floors 100 W/m 2 Concrete Floors 150 W/m
More informationradiant floor heating Floor Heating Mats Floor Heating Cables Thermostats
radiant floor heating Floor Heating Mats Floor Heating Cables Thermostats Radiant floor heating: A modern comfort solution Floor heating s vertical temperature distribution is the closest form of heating
More informationHardwired Model Shown. Installation & Operation Manual for WarmlyYours Infinity Towel Warmers
Hardwired Model Shown Installation & Operation Manual for WarmlyYours Infinity Towel Warmers Thank you for choosing your finely crafted WarmlyYours Towel Warmer. Now you can add luxury and comfort to your
More informationRadiant Thermostat 519
106103_dl_02 Radiant Thermostat 519 Installation & Operation Manual Introduction The Radiant Thermostat 519 accurately controls the room and/or floor temperature for a hydronic heating zone using Pulse
More informationfloor heating system
floor heating system Installation manual Instrukcja montażu Инструкция по установке EN PL RU EN The package contains: Thin self-adhesive heating mat Thermostat and temperature sensor (option) Installation
More informationI.D.L. Heaters Thermal Products Ltd. IdealMat Installation Manual
I.D.L. Heaters Thermal Products Ltd. IdealMat Installation Manual 0 1 The Most Luxurious and Safe System For Underfloor Heating Table of Contents Important Instructions 3 Safety Instructions 4 Before Starting
More informationCarbon Film Installation Instructions
Contents Page 2 Page 3 Page 4 Page 5 Page 8 Product Overview Pre-Installation & Electrical Provision Depron Underlay Installation Carbon Film Installation - Under Wood/Laminate Flooring Notes & Trouble
More informationI.D.L. Heaters Thermal Products Ltd. Roll n Warm Installation Manual
I.D.L. Heaters Thermal Products Ltd. Roll n Warm Installation Manual 0 The Most Luxurious and Safe System For Underfloor Heating Table of Contents Important Instructions 2 Safety Instructions 3 Before
More informationELECTRIC UNDERFLOOR HEATING SYSTEMS. Operating Guide & Guarantee. The Underfloor Heating Specialists Tel:
ELECTRIC UNDERFLOOR HEATING SYSTEMS The Underfloor Heating Specialists Tel: 0800 954 8862 Operating Guide & Guarantee www.myheat.co.uk Operating Guide Operation of your heating system is similar to other
More informationCarbon Heating Film. Failure to follow these instructions may result in fire, electrical shock, property damage, personal injury, or death.
Carbon Heating Film Easy to install. Does not circulate pollutants, dust, dirt, allergens or dry air. May be installed on wall, ceiling, under laminate, engineered wood floors or tile. Brings soothing
More informationUnderlaminate Foil Heater
Installation Manual: Underlaminate Foil Heater TECHNICAL HELPLINE 0845 345 2288 n online at warmup.co.uk IMPORTANT Read this manual before attempting to install your foil heater. Incorrect installation
More informationInstalling Underfloor Heating Film. 1. Layout of electric underfloor heating systems
Read through this entire manual before starting installation. May be installed under laminate, engineered wood or approved hardwood floors. See flooring manufacturer s specifications and instructions.
More informationLIFETIME. INSTALLATION MANUAL efoil WARRANTY
INSTALLATION MANUAL efoil LIFETIME WARRANTY Before you begin installing, read through these instructions carefully and check that you have all the components required. 01473 276677 www.elementsunderfloorheating.co.uk
More informationIdealFILM. Do-It-Yourself Installation Manual
IdealFILM Do-It-Yourself Installation Manual Comfortable Warm Floors Benefits of using RSG Idealfilm Heats from the floor up for better heat distribution throughout the room No dust or allergens blown
More informationInstallation & Operation Manual for WarmlyYours Riviera Towel Warmers
Installation & Operation Manual for WarmlyYours Riviera Towel Warmers Thank you for choosing your finely crafted WarmlyYours Towel Warmer. Now you can add luxury and comfort to your bathroom with the soothing
More informationInstallation Manual. Warmset. Warmset srl. Floor heating system
Installation Manual Warmset Warmset srl Floor heating system General instructions before starting!! The device can be used by children elder than 8 years, by persons with reduced physical, mental and sensitive
More informationDOMOTHERM CLASSIC TWIN/S MAT
Floor warming products 2013 V 10.12.2012 DOMOTHERM CLASSIC TWIN/S MAT An ideal solution for the whole house Ultra thin cable (2mm) Energy efficient Easy to install Domotherm Twin/s can be installed under:
More informationInstallation & Operation Manual
Humidity & Temperature Sensor 086 Accessories 086_D 08/12 Replaces: New Installation & Operation Manual Introduction The Humidity & Temperature Sensor 086 can be connected to select tekmar thermostats
More informationUS: CA:
Warmup DCM-PRO Installation Manual Technical Helpline US:1-888-927-6333 CA:1-888-592-7687 IMPORTANT! Please read this manual before attempting to install your Warmup product. Complete and submit your warranty
More informationELECTRIC HEATING THERMOSYSTEM
ELECTRIC RADIANT MAT 8200E INSTALLATION AND USE MANUAL heating passion ELECTRIC HEATING THERMOSYSTEM WARNING: For the guarantee to be valid, the product must be installed and handled as indicated in this
More informationHEAT CABLE underfloor heating
HEAT CABLE underfloor heating Installation Manual Thermosoft Heat Cable Installation Manual Page 1 INSTALLATION INSTRUCTIONS TM u n d e r f l o o r h e a t i n g c a b l e Please read these notes carefully
More informationFoil Heating System. Installation Manual. for Carpet and Laminate TECHNICAL HELPLINE 0800 WARMUP ( )
Installation Manual Foil Heating System for Carpet and Laminate IMPORTANT Read this manual before attempting to install your heater. Incorrect installation could damage the heater and will invalidate your
More informationInstallation Guide For your AHT Underfloor Heating System
Installation Guide For your AHT Underfloor Heating System Dear AHT Customer, Thank you for choosing the AHT underfloor heating system. It is designed to be simple to install and cost efficient to operate.
More informationUFM-T100H US ES CA Power Alarm Test TM
Alarm Power TM UFM-T100H US ES CA A E F I J K G B C D H L M N O P Q R S T U V W X US 1 3 2 Power Alarm 4 6 5 Power Alarm 7 9 8 Po we Ala r rm Power Alarm 10 11 Po we Po we Ala rm r 12 Pow Ala Ala rm r
More information- Data Brochure. This brochure is for Thermostats 510 and 511 (with sensor). The section on the 079 slab sensor installation is for the 511 only!
- Data Brochure Programmable Thermostat 510 and 511 D 510 02/12 Table of Contents Display / Keypad Operation... pg 1 Display Symbols... pg 2 General... pg 2-3 Sequence of Operation... pg 4 Installation
More informationairooncentre.co.uk irconcentre.co.uk Xpelair Low Energy Wall/Window Fan Range GX6 EC2 GXC6 EC2 Quick Order Hotline or
Xpelair Low Energy Wall/Window Fan Range GX6 EC2 GXC6 EC2 Installation and Maintenance Instructions Retain for future reference 3. To remove the impeller, unscrew the central screw with a 7mm nut runner
More informationUSER S MANUAL. Heat Recovery Ventilator. Vents Brig HRV 200 Vents Brig HRV 300
USER S MANUAL Heat Recovery Ventilator Vents Brig HRV 200 Vents Brig HRV 300 2 Brig HRV 200 (300) CONTENT Introduction... 3 Application... 3 Delivery set... 3 Unit designation key... 4 Basic unit dimensions...
More informationSingle-side powered heating cables
E DM Single-side powered heating cables Power output of 10 W/m. Characteristics and application ELEKTRA DM heating cables are manufactured according to IEC800 standard. They consist of a thin heating cable
More informationSFH136-CN TRUSTED FOR OVER 100 YEARS. Sunbeam Heater. Instruction Leaflet PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
TRUSTED FOR OVER 100 YEARS SFH136-CN Sunbeam Heater Instruction Leaflet PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS When using electrical
More informationXaact Spot. Xaact Hot Spot
Xaact Spot & Xaact Hot Spot INFORMATION & OPERATING INSTRUCTIONS READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE OPERATING THE MACHINE 78-00012 Rev. 101211 1 CONTENTS: Machine Specifications............
More informationInstallation And User Instructions. Devimat Warm Floor System Installation Instructions User Guide Trouble Shooter
GB Installation And User Instructions Devimat Warm Floor System Installation Instructions User Guide Trouble Shooter 1 Existing Floor Wooden Floors Concrete Floors Maximum load per m 2 100 W/m 2 150 W/m
More informationDUVAL 52 CEILING FAN MODELS #50201, Español p. 19 LISTED FOR DAMP LOCATION
DUVAL 52 CEILING FAN MODELS #50201, 50206 Español p. 19 LISTED FOR DAMP LOCATION Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-361-3883,
More informationIntro. Intro. Table of Contents
EN Intro Intro Dear AHT Customer, Thank you for choosing the AHT underfloor heating system. It is designed to be simple to install and cost efficient to operate. This guide provides the information you
More informationelectric floor heating for everyone Heating mats Heating cables Temperature controllers
electric floor heating Heating mats solutions for everyone Heating cables Temperature controllers Floor heating as the most favourable heating solution Of all heating systems, floor heating s vertical
More informationUNDERWOOD HEATING SYSTEM
INSTALLATION MANUAL Suitable for most wooden/laminate fl oors (always check with fl oor manufacturer) Ideal for most wood/laminate fl oors Easy to install Fully compliant to latest regulations CE approved
More informationELEKTRA HEATING MATS. Designed to be installed under laminate flooring and/or engineered wood UK PL RU. Installation manual
www.elektra.eu ELEKTRA HEATING MATS Designed to be installed under laminate flooring and/or engineered wood Installation manual Instrukcja montażu Èíñòðóêöèÿ ïî ìîíòàæó UK PL RU Purpose The ELEKTRA WoodTec
More informationMethod Statement. General Site preparation by others: Preparation for screed system by others: Preparation for plate system by others:
Method Statement. The One Stop Solution for Underfloor Heating. General Site preparation by others: Work areas to receive UFH must be watertight, dry, clean and clear of any debris or moveable obstructions.
More information! The Caution Symbol (exclamation point) alerts you to a "CAUTION", a safety or
I&M NUMBER: 316-42-10-1 Page: 1 Pre Installation Check to make sure that heater received is the same as that ordered. Elements may come in contact with each other during shipment. Minor adjustments to
More informationBIONAIRE HEATER. Instruction Leaflet. pure indoor living MODEL: BCH4130. Read instructions before operating. Retain for future reference.
pure indoor living BIONAIRE HEATER MODEL: BCH4130 Instruction Leaflet Read instructions before operating. Retain for future reference. Questions? Comments? Call 1-800-253-2764 in North America. PLEASE
More information2 INLET / HIGH HEAD DRAIN PUMP SYSTEMS MODELS , INSTALLATION INSTRUCTIONS PREINSTALLATION CHECKLIST
Your Peace of Mind is Our Top Priority Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies. MAIL TO: P.O. BOX 637 Louisville,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Unit 1 79 Friar Street Worcester WR1 2NT Tel: 01905 616 928 Fax:01905 611 240 E-mail: info@underfloorheatingsystems.co.uk Website: www.underfloorheatingsystems.co.uk ngsystems.co.uk
More informationSAFETY INFORMATION AND WARNINGS
This manual refers to the Model SST-3 control panel manufactured since October 31, 2013, which uses a universal (100 277 VAC; 50/60 Hz) power supply. Older units use a voltage-specific power supply and
More informationComfortTile Floor Heating Systems
ComfortTile Floor Heating Systems Luxurious Warmth for Your Floors The systems are easily installed under all types of floor surfaces to provide comfortable, even floor heat. ComfortTile radiant floor
More informationF1202 TRACE HEATING. Road & Ramp
Trace Heating Specialists Road & Ramp ROAD & RAMP HEATING ESH Trace Heating Ltd provide a comprehensive range of products to prevent the settlement of snow and formation of ice on roads, ramps and stairs.
More informationDISCONTINUED VERSION The information in this manual is no longer current. OPERATING & SERVICE MANUAL
BUNN HC-1 HC-2 HC-3 DISCONTINUED VERSION The information in this manual is no longer current. OPERATING & SERVICE MANUAL BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE:
More informationELECTRIC STOVE HEATER Models: FS2213B
ELECTRIC STOVE HEATER Models: FS2213B OWNER S MANUAL WARNING Read and understand this entire owner s manual, including all safety information, before plugging in or using this product. Failure to do so
More informationThe DEF-System by BRUGG. The Best Way to defeat the problem of DEF heat Installation Instructions
The -System by BRUGG The Best Way to defeat the problem of heat Installation Instructions -System Installation Instructions Content Page 3 Page 4 Page 5 Page 6 Page 7 Description of System Installation
More informationRV Products Division INSTALLATION INSTRUCTIONS FOR SERIES PACKAGE AIR CONDITIONER
RV Products Division INSTALLATION INSTRUCTIONS FOR 46413 SERIES PACKAGE AIR CONDITIONER 1. WARNINGS IMPORTANT NOTICE These instructions are for the use of qualified individuals specially trained and experienced
More informationINSTALLATION INSTRUCTIONS ONE LARGE ZONE
INSTALLATION INSTRUCTIONS ONE LARGE ZONE Unit 1 79 Friar Street Worcester WR1 2NT Tel: 01905 354 791 Fax: 01905 352 100 E-mail: info@underfloorheatingsystems.co.uk Website: www.underfloorheatingsystems.co.uk
More informationUser Manual. Electric Heating Element MEG DRY MOA REG 2 REG 3
User Manual Electric Heating Element MEG DRY MOA REG 2 REG 3 User Manual Our products have been designed and manufactured in such a way to ensure that all quality, functionality and aesthetic requirements
More informationSECTION SECURITY TESTING AND COMMISSIONING
SECTION 280800 - SECURITY TESTING AND COMMISSIONING PART 1 - GENERAL 1.1 WORK INCLUDES A. General Description: This specification section covers the provision of preliminary testing, acceptance testing,
More informationRoyden. Look how easy it is to roll out the heat
Royden Look how easy it is to roll out the heat 6 good reasons to select Royden infloor heating foil 1. Easily installed Royden heating foil comes on the roll, ready to fit. Whatever the room size or shape
More informationOPERATING MANUAL Gfp 255C Please read this manual carefully before operating!
OPERATING MANUAL Gfp 255C Please read this manual carefully before operating! Unpacking, assembly, and operating videos are available at www.gfpsmoothstart.com 1 Table of Contents Gfp 255C March 2015 Contents
More informationOPERATING AND INSTALLATION MANUAL
OPERATING AND INSTALLATION MANUAL TANKLESS ELECTRIC WATER HEATER WITH ELECTRO-MECHANICAL FLOW SWITCH» MINI 2» MINI 2.5» MINI 3» MINI 3.5» MINI 4» MINI 6 The Mini series is tested and certified by WQA against
More informationInstallation Guide. Maximum Area 20m 2
Installation Guide Maximum Area 20m 2 i PLEASE READ THIS INSTALLATION GUIDE CAREFULLY BEFORE BEGINNING ANY WORK TO ENSURE A SAFE & TROUBLE FREE INSTALLATION. Parts provided with pack 4 Parts provided with
More informationSimple. Smart. Solutions. ROOM PACK Z2105/239/0812. Step by Step Installation Guide
Simple. Smart. Solutions. ROOM PACK Z2105/239/0812 Step by Step Installation Guide 1. Room Pack Overview 2. Temperature Settings 3. Operation 4. Wiring 5. Installing Your Room Pack Before you get started
More informationHeating Mats. Single-side power supply Double-side power supply
TThe Heating Mats Single-side power supply Double-side power supply AApplication The heating mats may be used as the basic heating system or they may supplement the existing system. The most often they
More informationOverview Frost Heave Prevention for Freezer floors on ground.
PLEASE NOTE The floor sensor MUST be installed such that it may be REMOVED for service if required! The sensor probe should be installed into a conduit with no more than one wide-angle bend. This should
More informationWATLOW IND. WATROD Flange Heater Installation & Maintenance Manual I&M NUMBER: Page: 1 Date:6/11/2008 Rev: 2.00
I&M NUMBER: 316-42-8-1 Page: 1 _ Pre Installation Check to make sure that heater received is the same as that ordered. Elements may come in contact with each other during shipment. Minor adjustments to
More informationInstallation Instructions
Installation Instructions 3M Light Mat Series 3635-1000 Installation Bulletin 3635-1000 Release D, Effective July 2010 (Replaces C, Apr 2010) See Bulletin Change Summary at end of Bulletin Product Description
More informationelectric floor heating Heating mats Heating cables Temperature controllers
electric floor heating Heating mats Heating cables Temperature controllers Floor heating as the most favourable heating solution Of all heating systems, floor heating s vertical temperature distribution
More informationINSTRUCTION MANUAL P Heating and 1 Cooling
REPLACEMENT COMPONENTS DIVISION CARRIER CORPORATION www.totaltouch.info Technical Support: 1-866-90TOUCH (1-866-908-6824) INSTRUCTION MANUAL P286-1200 2 Heating and 1 Cooling Physical Dimensions Case:
More informationWATLOW ELECTRIC MFG CO. FIREBAR Screw Plug Installation & Maintenance Manual I&M NUMBER: Page: 1 Date: 11/25/2013 Rev: 4.
I&M NUMBER: 316-42-3-1 Page: 1 Pre Installation Check to make sure that heater received is the same as that ordered. Elements may come in contact with each other during shipment. Minor adjustments to elements
More informationUse and Care Manual. Flammable Material Storage Refrigerator LRBFS06W1HC
Use and Care Manual Flammable Material Storage Refrigerator LRBFS06W1HC 7085 471-00 Table of Contents Table of Contents Page Please Read and Follow these Instructions... 2 California Proposition 65...
More informationInstallation & Operation Manual
Installation & Operation Manual Radiant Thermostat 519 519_D 06/16 Zoning Replaces: 03/13 Introduction The Radiant Thermostat 519 accurately controls the room and/or floor temperature for a hydronic heating
More informationWATLOW IND. FIREBAR Flange Heater Installation & Maintenance Manual I&M NUMBER: Page: 1 Date: 6/11/2008 Rev: 2.00
I&M NUMBER: 316-42-2-1 Page: 1 Pre Installation Check to make sure that heater received is the same as that ordered. Elements may come in contact with each other during shipment. Minor adjustments to elements
More informationInstallation Manual. Warmset. Warmset srl. Floor heating system
Installation Manual Warmset Warmset srl Floor heating system General instructions before starting!! The device can be used by children elder than 8 years, by persons with reduced physical, mental and sensitive
More information