DESIGN GUIDELINES AND TECHNICAL STANDARDS
|
|
|
- Julius Wilkerson
- 5 years ago
- Views:
Transcription
1 DESIGN GUIDELINES AND TECHNICAL STANDARDS Date of Issuance: January 1, 2014
2
3 DIVISION 22 PLUMBING SECTION DOMESTIC WATER DISTRIBUTION SYSTEM 1. General: This section outlines general requirements for domestic water distribution systems. 2. Design Considerations: 3. Materials: a. Potable water pipe shall be routed so that the circuit terminates at high use areas, such as washrooms. The purpose is to avoid stagnation leading to a high bacteria count. b. Piping shall be routed orthogonally (no diagonal shortcuts). c. Domestic cold water, domestic hot water supply and recirculation, laboratory cold water, laboratory hot water and recirculation, and fill/makeup water lines shall be copper. d. Faucets and fixtures, such as emergency showers, eye wash, dishwashers, and autoclaves shall have local shutoff valves within five feet of the faucet/fixture. Valves must be accessible. e. No piping with a fluid shall be routed over electrical busway housings. For electrical busway housings provide a minimum 24 inches on top, both sides and the bottom. f. An excellent table giving the chemical resistance of four commonly used thermoplastic piping materials can be found in the Technical Manual published by the Charlotte Pipe and Foundry Company, Industrial Division ( ). g. In lab buildings, consider a redundant distribution system such as a pair of risers cross connected at the floors. a. Steel and copper pipe shall be built and stamped to meet ASTM standards. b. Copper Tubing: i. Copper tubing shall be type L hard drawn. ii. Copper tubing shall be 95-5 soldered. Solder shall be lead free. iii. Grooved copper tubing is not permitted. c. Galvanized pipe is not permitted. DOMESTIC WATER DISTRIBUTION SYSTEM
4 d. Laboratory Drain and Vent Piping: i. General: 1. Joints shall be mechanical. Beading, fusing caulking, or welding of joints is not acceptable. 2. Review requirements for neutralizing basins. ii. Material: PP (polypropylene). iii. Acceptable Manufactures for Polypropylene: 1. Enfield Industrial Corp. END OF SECTION DOMESTIC WATER DISTRIBUTION SYSTEM
5 DIVISION 22 PLUMBING SECTION PLUMBING SPECIALTIES 1. General: this section outlines general requirements for plumbing specialties. 2. Materials: a. Ball Valves: i. Ball valves shall be bronze, 600 psig WOG, full port, with a 316 stainless steel ball and stem. ii. Insulated valves shall have a 2-1/4 in. stem extension. iii. Acceptable Manufacturers: b. Gate Valves: 1. Conbraco Industries, Inc. (APOLLO) 2. Neles-Jamesbury, Inc. 3. Watts Regulator Co. i. Gate valves are not permitted. c. Backflow Preventers: d. P-Traps: END OF SECTION i. Backflow preventers shall be by the Watts Regulator Company, Series Exception: Fire Protection Systems. i. Trim P-traps and accessories shall be 17 gauge minimum. PLUMBING SPECIALTIES
6 This page intentionally left blank PLUMBING SPECIALTIES
7 DIVISION 22 PLUMBING SECTION PLUMBING FIXTURES 1. General: This section outlines general requirements for plumbing fixtures. 2. Design Considerations: 3. Materials: a. When possible sinks, urinals and closets should match existing fixtures for renovation projects. b. Review project specific requirements with NU Project Manager. a. Sinks, Urinals, and Closets: i. Acceptable Manufacturers: 1. American Standard, Inc. 2. Crane Company. 3. Eljer Plumbingware. 4. Kohler Company. b. Faucets, Except Laboratories: i. Electronic eye faucets are preferred in public washrooms. The transformer shall be hard wired. Spring loaded non-electric faucets are not acceptable. ii. Coordinate power requirements and indicate on electrical power drawings. iii. Acceptable Manufacturers: 1. The Chicago Faucet Company. 2. Kohler. 3. Sloan Valve Company. c. Laboratory Faucets and Hardware: i. Laboratory, eyewash and shower faucets, vacuum breakers, and appurtenances shall be furnished by The Chicago Faucet Company. PLUMBING FIXTURES
8 d. Urinal Flush Valves: i. Acceptable Manufacturer: 1. Sloan Valve Company, Model (1.0 gpf). e. Water Closet Flush Valves: i. Toilet flush valves shall have a transformer and shall be hard wired with a courtesy flush override button. Coordinate power requirements and indicate on electrical power drawings. 1. Exception: Tank-type toilets. ii. Acceptable Products: 1. Chicago and Evanston campus: 111ES-S (1.6 gpf) iii. Acceptable Manufacturers: f. Drinking Fountains: 1. Sloan Valve Company. i. Design Considerations: 1. Provide dual-height drinking fountains with bottle fillers. 2. Coordinate power requirements and indicate on electrical power drawings. ii. Acceptable Manufacturers: g. Hand Dryers: 1. Halsey Taylor. a. Basis-of-Design Product: HAC Hydro-Boost, barrier-free, Model HTHB-HAC8BL-WF. 2. Elkay Mfg. Co. i. Northwestern prefers paper towels over electric hand dryers. Review specific requirements with NU Project Manager. ii. If provided, hand dryers shall be surface mounted equipped with an infrared sensor and an automatic 60 second cut-off switch, 120 Vac. Coordinate power requirements and indicate on electrical power drawings. PLUMBING FIXTURES
9 END OF SECTION iii. Acceptable Manufacturer: 1. Sloan Valve Company, Model EHD-401. PLUMBING FIXTURES
10 This page intentionally left blank PLUMBING FIXTURES
11 DIVISION 22 PLUMBING SECTION PLUMBING EQUIPMENT 1. General: This section outlines general requirements for plumbing equipment. 2. Materials: END OF SECTION a. Domestic Water Booster System: i. No encased (can type) pumps are permitted. ii. Above 10 hp domestic water booster pumps shall be variable speed. iii. Acceptable Manufacturers: 1. Metropolitan Industries, Inc. b. Sump and Ejector Pumps: i. Acceptable Manufacturers: 1. Metropolitan Industries, Inc. 2. Hydro O Matic Pumps, A Division of Wylain, Inc. 3. No submersible sump pumps are permitted, except in elevator shafts. PLUMBING EQUIPMENT
12 This page intentionally left blank PLUMBING EQUIPMENT
DESIGN AND CONSTRUCTION STANDARDS GENERAL DESIGN GUIDELINES
2.05 PLUMBING GENERAL DESIGN AND CONSTRUCTION STANDARDS GENERAL DESIGN GUIDELINES - 2.05 It is expected that the plumbing design professional will conform to accepted good engineering design practices.
Title: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: Plumbing Standards
Date Description of Change Pages / Sections Modified ID 8/5/17 Entire document - mgl PART 1 - INTRODUCTION 1.1 This section applies to Plumbing for campus institutional facilities. A. Purpose: Yale University
DESIGN STANDARDS SECTION PLUMBING FIXTURES AND EQUIPMENT. 1.3 Wall hung toilet room fixtures. Urinals for handicapped may be stall type.
PART 1 - GENERAL 1.1 Toilet rooms and utility rooms to have floor drains at lowest point. 1.2 Utilize Exposed Flushometers. 1.3 Wall hung toilet room fixtures. Urinals for handicapped may be stall type.
DOMESTIC WATER PACKAGED BOOSTER PUMPS
DIVISION 22 PLUMBING 22 11 16 DOMESTIC WATER PIPING 22 11 19 DOMESTIC WATER PIPING SPECIALTIES 1. To facilitate landscape and other maintenance operations, exterior hose bibs shall be provided at 150 foot
DUKE UNIVERSITY CONSTRUCTION STANDARDS
1 22 40 00 Plumbing Fixtures 1. General A. Definitions 1. Section includes a. Water closets and urinals b. Lavatories, sinks, and service sinks c. Electric water coolers, drinking fountains, d. Showers
2. All necessary storm and sanitary pumps shall be tied into emergency power, and sump levels shall be monitored electronically through the B.A.S.
DIVISION 22 00 00 22 30 00 EQUIPMENT Page 1 of 10 22 30 00 EQUIPMENT 22 01 01 GENERAL REQUIREMENTS General 1. All plumbing shall comply with the B.C. Plumbing Code. 1. Avoid the use of storm pumps and
2016 Plumbing Supplemental Plan Review List
Building Division 555 Santa Clara Street Vallejo CA 94590 707.648.4374 2016 Plumbing Supplemental Plan Review List POTABLE WATER SYSTEM P1. Specify which fixtures are for private use and which are for
DESIGN STANDARDS SECTION Toilet rooms and utility rooms to have floor drains at lowest point.
PART 1 - GENERAL 1.01 Toilet rooms and utility rooms to have floor drains at lowest point. 1.02 Utilize Exposed Flushometers. 1.03 Wall hung toilet room fixtures. Urinals for handicapped may be stall type.
B. Shop Drawings: Include diagrams for power, signal, and control wiring.
SECTION224213.13 -COMMERCIAL WATERCLOSETS PART 1- GENERAL 1.1 SUMMARY Section Includes: 1. Water closets. 2. Flushometer valves. 3. Toilet seats. 1.2 ACTION SUBMITTALS Product Data: For each type of product.
SECTION DOMESTIC WATER PIPING SPECIALTIES
SECTION 22 11 19 DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
GARCIA GALUSKA DESOUSA Consulting Engineers
L#58619/Page 1/November 1, 2017 PLUMBING Executive Summary: Presently, the Plumbing Systems serving the building are cold water, hot water, sanitary, waste and vent system, storm drain piping, and natural
2). Crane Co. 4). Kohler Co. 5). Universal-Rundle Corp. Revised September 29, 2017 Commercial Plumbing Fixtures
PART 1: GENERAL A. This Section provides design standards for plumbing fixtures and trim. Certification of compliance with specified ANSI, UL, and ASHRAE Standards will be required, as appropriate, for
DESIGN STANDARDS SECTION Toilet rooms and utility rooms to have floor drains at lowest point.
PART 1 - GENERAL 1.01 Toilet rooms and utility rooms to have floor drains at lowest point. 1.02 Utilize Exposed Flushometers. 1.03 Utilize wall hung toilet room fixtures. Urinals for handicapped may be
DIVISION 22: PLUMBING DESIGN STANDARDS TABLE OF CONTENTS
DIVISION 22: PLUMBING DESIGN STANDARDS TABLE OF CONTENTS I. PURPOSE II. III. IV. GENERAL A. DESIGN DOCUMENTS B. INSPECTIONS C. CLOSE-OUT Project Record Documentation Training D. ENERGY USE E. LABELING
Sanitary Drainage Systems
11.1 MATERIALS See Section 3.1. Sanitary Drainage Systems 11.2 BUILDING SEWERS AND BUILDING DRAINS 11.2.1 Sewer or Drain in Filled Ground Chapter 11 Building sewers or building drains that are installed
SECTION LABORATORY and DE-IONIZED WATER SYSTEMS STANDARD CONSTRUCTION STANDARD
PART 1: GENERAL 1.01 Codes and Standards: A. Plumbing Code Compliance: Comply with applicable portions of National Standard Plumbing Code pertaining to selection and installation of Plumbing materials
C. ASSE 1013: Performance Requirements for Reduced Pressure Principle Backflow Preventers.
SECTION 22 10 00 PLUMBING PIPING AND PUMPS PART 1 - GENERAL 1.1 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
DESIGN CRITERIA See Part II for additional information regarding Energy and Water Efficiency, etc.
DIVISION 22 PLUMBING DESIGN CRITERIA See Part II for additional information regarding Energy and Water Efficiency, etc. SYSTEMS DEFINITION Campus is served by three water distribution systems; potable,
21. Plumbing fixture mixing valves, PRV, electronic faucets and flush valve(excluding batteries)optional Cost proposal to include these device
DIVISION 23800 APPENDIX A ASHTABULA CAMPUS: 1. Air Handling Equipment And Appurtenances 2. Exhaust Fans 3. Fume Hood Exhaust Fans 4. Fume Hood monitoring devices and annual certification of face velocity
PLUMBING DESIGN GUIDELINES SECTION DESIGN GUIDELINES DUVAL COUNTY PUBLIC SCHOOLS
The Design Guidelines, which follow, are intended to supplement the Educational Specifications and State Requirements for Educational Facilities (SREF). Note: All fittings shall be installed by no less
Union County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 22 40 00 - PLUMBING FIXTURES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Faucets for lavatories, bathtubs, bathtub/showers, showers and sinks. 2. Flushometers. 3. Toilet
A. This Section includes the following domestic water piping specialties:
SECTION 221119 DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
Yale University Design Standards
Change History Date Description of Change Pages / Sections Modified Change Approver Initials 3/26/13 Add text encouraging discussion of innovation in 2 15410, A (Summary) SO newly available products. 3/26/13
BSD Technical Standard. Division 22: Plumbing
Division 22: Plumbing I. PURPOSE This technical standard is a narrative describing Beaverton School District s (BSD s) Basis of Design for mechanical plumbing systems. The information contained herein
AIRPORT PLUMBING DESIGN STANDARDS REV. 2 11/02/2015
1.1 GOALS The goal of this section is to provide guidance in the design of Plumbing and Fire Protection systems to LAWA standards. The LAWA Plumbing Design Standards are a compilation of general design
GENERAL PLUMBING REQUIREMENTS
22 00 00 GENERAL PLUMBING REQUIRMENTS i. 00 00 07 Design Professional Design Process Requirements ii. 00 00 08 Design Professional Documentation Requirements and Deliverables iii. 01 81 00 Facility Performance
1. Division 22 Section "Emergency Plumbing Fixtures." 2. Division 22 Section "Drinking Fountains and Water Coolers."
Page 224000-1 SECTION 224000 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
GENERAL PLUMBING REQUIREMENTS
22 00 00 GENERAL PLUMBING REQUIRMENTS 1. GENERAL A. Related sections: i. 00 00 07 Design Professional Design Process Requirements ii. 00 00 08 Design Professional Documentation Requirements and Deliverables
2009 IPC ,IMC Q &A ANDIFGC
2009 IPC,IMC ANDIFGC Q &A TABLE OF CONTENTS PREFACE.... ix ABOUT THE INTERNATIONAL CODE COUNCIL...x IPC CHAPTER 1 SCOPE AND ADMINISTRATION...1 Section 101 General... 1 Section 102 Applicability... 1 Section
BRADLEY HALO EMERGENCY PLUMBING FIXTURES (Short Form Version)
BRADLEY HALO EMERGENCY PLUMBING FIXTURES (Short Form Version) Bradley Halo Emergency Plumbing Fixtures are a new generation in safety equipment, featuring separate supply and waste piping to eye/face wash,
Matrix of changes for the National Standard Plumbing Code July 2013
Matrix of changes for the National Standard Plumbing Code July 2013 Item # Section Number Person Submitting Change Committee Action 10-77 10.20.8 and Table 3.1.3 XI Certification 10-82 12.16 Size and Lengths
SECTION PLUMBING FIXTURES AND TRIM. A. Types of plumbing fixtures required for the project include the following:
SECTION 15440 PART I - GENERAL 1.01 WORK INCLUDED A. Types of plumbing fixtures required for the project include the following: 1. Water Closets 2. Urinals 3. Lavatories 4. Mop Sink 5. Sinks 6. Electric
Automatic Temperature Controller (ATC)
NEW FROM APOLLO...THE FIRST MULTIPLE-FIXTURE HI-LO MIXING VALVE THAT MEETS ASSE 1017 AND THE NEW ASSE 1069 STANDARD Only Apollo offers fast delivery on the first water temperature mixing assembly to meet
PERFORMANCE TECHNICAL SPECIFICATION *************************************************************************** SECTION D20 PLUMBING 02/18
NAVFAC PTS-D20 (February 2018) ------------------------------ Preparing Activity: NAVFAC SUPERSEDING PTS-D20 (September 2016) PERFORMANCE TECHNICAL SPECIFICATION SECTION D20 PLUMBING 02/18 NOTE: This section
A. Section Joint Sealants: Seal fixtures to walls and floors.
SECTION 224000 - PLUMBING FIXTURES PART 1 GENERAL 1.1 SECTION INCLUDES A. Water closets. B. Urinals. C. Lavatories. D. Sinks. E. Service sinks. F. Showers. G. Wash fountains. H. Eye wash fountains. 1.2
SAFETY SHOWERS AND EYEWASHES 1.01 RELATED CORNELL DESIGN AND CONSTRUCTION STANDARDS
224500 SAFETY SHOWERS AND EYEWASHES Cornell s Design and Construction Standards provide mandatory design constraints and acceptable or required products for all construction at Cornell University. These
BRADLEY HALO EMERGENCY PLUMBING FIXTURES
BRADLEY HALO EMERGENCY PLUMBING FIXTURES Bradley Halo Emergency Plumbing Fixtures are a new generation in safety equipment, featuring separate supply and waste piping to eye/face wash, ergonomic hand activation
Read Only Copy Not For Distribution. Chapter 10. Water Supply and Distribution 10.1 QUALITY OF WATER SUPPLY 10.2 RESERVED 10.
Water Supply and Distribution 10.1 QUALITY OF WATER SUPPLY a. Only potable water shall be supplied to plumbing fixtures used for drinking, bathing, culinary use or the processing of food, medical or pharmaceutical
PLUMBING REQUIREMENTS
PLUMBING REQUIREMENTS This handout is a compilation of the standard requirements based on the State Plumbing Code and City Ordinance for projects of this type. This information sheet does not contain all
Special Requirements For Health Care Facilities
Chapter 14 Special Requirements For Health Care Facilities 14.1 GENERAL This Chapter applies to special fixtures and systems that occur in health care facilities and to the special plumbing requirements
Mechanical Inspection Plumbing
0811 Fixtures Sinks, drinking fountains, water closets, showers, etc. Classroom Sinks. Classroom sinks (19) are enameled cast iron self rimming side ledge with gooseneck faucet trim with index handles,
4. Provide brass valve tags marked for the service. See pertinent service specification for valve type.
Section includes various guidelines for valves, instrumentation for process systems, meters, thermometers, and gauges. This design guideline is written to the designer of record (DOR). This guideline is
B. Provide unique numbers for all applicable equipment, valves, and similar.
UDIVISION 22 PLUMBING 22 00 00 PLUMBING BASIC MECHANICAL REQUIREMENTS A. Provide a list of symbols on drawings. B. Provide unique numbers for all applicable equipment, valves, and similar. C. Schedule
LAV FCO WCO NOTES: CONTRACTOR SHALL REFER TO ARCHITECTURAL DRAWINGS FOR MOUNT HEIGHTS AND SPECIAL MOUNTING INSTRUCTION AND LIMITATIONS.
ELECTRIC WATER HEATER SCHEDULE DESIGNATION MODEL MANUFACTURER STORAGE RECOVERY TEMPERATURE LEAVING ELECTRICAL CHARACTERISTICS REMARKS/SPECIAL INSTRUCTIONS NUMBER GALLONS RATE RISE WATER K.W. VOLTAGE PHASE
Mechanical System Description
1. Building Description: Mechanical System Description The building is a Type-1B construction, 9-levels, non-high rise building with 67 affordable family housing units. The first level of the structure
DESIGN AND CONSTRUCTION STANDARDS July 2011
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design for new construction and renovations.
COMMERCIAL PERMIT APPLICATION AND CHECKLIST. Depending on the scope of your project, the following submittal requirements will apply:
Planning/Building Department 115 Ramsdell Street Fircrest WA 98466 (253) 564-8902 COMMERCIAL PERMIT APPLICATION AND CHECKLIST Depending on the scope of your project, the following submittal requirements
HWC NOTES: CONTRACTOR SHALL REFER TO ARCHITECTURAL DRAWINGS FOR MOUNT HEIGHTS AND SPECIAL MOUNTING INSTRUCTION AND LIMITATIONS.
ELECTRIC WATER HEATER SCHEDULE DESIGNATION MODEL MANUFACTURER STORAGE RECOVERY TEMPERATURE LEAVING ELECTRICAL CHARACTERISTICS REMARKS/SPECIAL INSTRUCTIONS NUMBER GALLONS RATE RISE WATER K.W. VOLTAGE PHASE
TABLE OF CONTENTS DIVISION 22 - MECHANICAL
TABLE OF CONTENTS DIVISION 22 - MECHANICAL 22 00 00 PLUMBING WORK...1 22 00 01 GENERAL...1 22 00 02 REFERENCES, REGULATORY REQUIREMENTS...1 22 00 03 RELATED SECTIONS of the SPECIFICATIONS...1 22 00 04
University of Rochester October 17, 2008 Brooks Landing Business Center
SECTION 224200 COMMERCIAL PLUMBING FIXTURES PART 1 - GENERAL 1.1 WORK INCLUDED A. Provide all labor, materials, equipment and services to perform operations required for the complete installation and related
DOCUMENT TABLE OF CONTENTS
DOCUMENT 00003 June 16, 2005 TABLE OF CONTENTS DOCUMENT NO. INTRODUCTORY INFORMATION DOCUMENT 00003 TABLE OF CONTENTS DIVISION 1 GENERAL REQUIREMENTS SECTION 01011 SECTION 01025 SSP21.1-1 SECTION 01026
Pipe Sizing Table. Hydraulic Load Served (fixture units)
MODULE 1 INTRODUCTION Notes: A Pipe Type Horizontal branch Pipe Sizing Table Hydraulic Load Served (fixture units) Size (in.) Code Reference 2 + 1.5 = 3.5 2 7.4.9.1.(1) B Soil stack 13.5 + 13.5 = 27 3
A. General: comply with appropriate standards. 1. International Association of Plumbing and Mechanical Officials: IAPMO. 2. California State AB 1953.
SECTION 22 40 00 - PLUMBING FIXTURES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Water closets. 2. Urinals. 3. Lavatories. 4. Sinks. 5. Service sinks. 6. Electric water coolers. 7. Wash fountains.
NYC Department of Education
Asset: P.S. 841- QUEENS, 48-25 37TH STREET, New York, 11104 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2018-04-02 12:54 PM 2018-05-14 12:28 PM Asset Data Are there fuel tanks? Total
NYC Department of Education
Asset: J.H.S. 216 - QUEENS, 64-20 175 STREET, New York, 11365 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2017-11-06 8:51 AM 2017-11-22 10:04 AM Asset Data Are there fuel tanks? Total
AIRPORT PLUMBING DESIGN STANDARDS REV. 3 3/18/2016
1.1 GOALS The goal of this section is to provide guidance in the design of Plumbing and Fire Protection systems to LAWA standards. The LAWA Plumbing Design Standards are a compilation of general design
Plumbing and Drainage
Dufferin-Peel Catholic District School Board STANDARD TEXT FOR Plumbing and Drainage for ELEMENTARY AND SECONDARY SCHOOLS Prepared by the Plant Department Formatted by the Design Department THE INFORMATION
SECTION PLUMBING
SECTION 22 10 00 PLUMBING PART 1 GENERAL 1.1 WORK INCLUDED A. Furnish all labor, material and equipment necessary for the complete installation of the sanitary sewer system (including soil and vent piping),
Building Utilities 1 Plumbing and Sanitary Systems
Building Utilities 1 Plumbing and Sanitary Systems Taken from UST Architecture exams by Arch. Rafael Alli Recommended review material for UST Preboard Exam Prepared by: arkireviewph.multiply.com Types
TABLE OF CONTENTS Limitations of Authority...6 Table Swimming Pool, Spa, and Hot Tub Permit Fees...7
TABLE OF CONTENTS CHAPTER 1 ADMINISTRATION..............1 101.0 General.......................1 101.1 Title..........................1 101.2 Scope........................1 101.3 Purpose......................1
NYC Department of Education
Asset: HS FOR MATH, SCI & ENGINEERING-M, 240 CONVENT AVENUE, New York, 10031 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2017-12-20 12:04 PM 2018-01-05 5:32 PM Asset Data Are there
A. All fixtures shall meet the requirements of ANSI A117.1, ANSI Z124.2 and the State of Texas Accessibility Standards (TAS).
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
APPENDIX A. A 3.2 Determine the elevation of the highest. A 3.3 Subtract the sum of loss in static pressure
APPENDIX A RECOMMENDED RULES FOR SIZING THE WATER SUPPLY SYSTEM Because of the variable conditions encountered, it is impractical to lay down definite detailed rules of procedure for determining the sizes
TABLE OF CONTENTS. CHAPTER 2 DEFINITIONS General Applicability Definition of Terms General...
TABLE OF CONTENTS CHAPTER 1 ADMINISTRATION................1 101.0 Title, Scope, and General...........1 101.1 Title............................1 101.2 Purpose.........................1 101.3 Plans Required...................1
Perkins Statewide Articulation Agreement. Documentation item: Secondary Competency Task List Coversheet
Perkins Statewide Articulation Agreement Documentation item: Secondary Task List Coversheet The Secondary School agrees to: A. Implement the approved PDE Program(s) of Study. B. Provide assessment of student
A. This Section includes the following emergency plumbing fixtures:
Page 224500-1 SECTION 224500 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
STEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
MATERIALS Traps TRAPS. No. IPC IRC Description
MATERIALS Traps TRAPS MAX " MAX 0" No. IPC IRC Description 00. P0.6 00. P0.6 00. P0. 00. () P0.6 Exc. Vertical distance from fixture to the trap weir can not exceed ". Horizontal distance from the fixture
ICP Plumbing Exam. Name: Carefully read each question and then circle the letter of the best answer.
ICP Plumbing Exam Name: Date: Score: Carefully read each question and then circle the letter of the best answer. 1. A 1 inch diameter faucet, where the inside edge of the spout opening is 2.5 inches away
1 WATERMARK CERTIFICATION SCHEME SCHEDULE OF PRODUCTS This document was adopted 1 August 2017 and replaced the WaterMark Schedule of Specifications
1 WATERMARK CERTIFICATION SCHEME SCHEDULE OF PRODUCTS This document was adopted 1 August 2017 and replaced the WaterMark Schedule of Specifications Product type Application Specification Appliances Bedpan
SECTION ELECTRIC WATER HEATERS
SECTION 22 36 01 ELECTRIC PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
University of New Hampshire Scholars' Repository
University of New Hampshire University of New Hampshire Scholars' Repository Division 22 Plumbing Chapter 5 Technical Construction and Renovation Standards Fall 9-8-2018 224000 - Plumbing Stephanie L.
SECTION PLUMBING EQUIPMENT Piping (Plumbing). 2. Division 16 - Electrical Wiring and Connections.
SECTION 15450 PLUMBING EQUIPMENT PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15410 - Piping (Plumbing). 2. Division 16 - Electrical Wiring and Connections. 1.02 SUBMITTALS A. Submit properly identified
HYDRONIC TEMPERING VALVES. Part No. High Temp F. Part No. Low Temp F
34-200 SERIES HYDRONIC TEMPERING VALVES The Apollo Model TV (34-200 Series) thermostatic mixing valve provides non-asse extension of water heater capacity and hot water temperature control in hydronic
SECTION PLUMBING FIXTURES
CSUEB Pioneer Heights Phase r 15410 Page 1 SECTION 15410 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
SCHOOL DISTRICT PALM BEACH COUNTY BUILDING DEPARTMENT PLAN REVIEW CHECK LIST -- PLUMBING
SCHOOL DISTRICT PALM BEACH COUNTY BUILDING DEPARTMENT PLAN REVIEW CHECK LIST -- PLUMBING 3300 SUMMIT BOULEVARD WEST PALM BEACH, FLORIDA 33406 TEL (561) 688-7687 FAX (561) 688-7654 http://www.palmbeach.k12.fl.us/fm/bd/index.htm
BACKFLOW PREVENTION GUIDE FOR COMMERCIAL, INSTITUTIONAL AND INDUSTRIAL DEVELOPMENTS
AG AVB PVB DCVA PA 1 Abattoir (slaughter house) 2 Air compressor oil cooler 3 Agricultural chemicals (sprayers 4 Animal watering 5 Apartment building (within the scope of Part 3 of the Ontario Building
NYC Department of Education
Asset: LIBERTY HS - MANHATTAN, 250 WEST 18 STREET, New York, 10011 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2018-01-29 11:32 AM 2018-02-01 10:16 AM Asset Data Are there fuel tanks?
Wastewater. Guidelines for Sizing mscdirect.com. Call MSC today to learn about the latest LittleGiant products.
Wastewater Guidelines for Sizing Features These guidelines cover the steps which need to be taken to accurately select the correct sewage pump and applicable systems to use in sewage ejectors. Work through
PERFORMANCE TECHNICAL SPECIFICATION *************************************************************************** SECTION D20 PLUMBING 02/18
NAVFAC PTS-D20 (February 2018) ------------------------------ Preparing Activity: NAVFAC SUPERSEDING PTS-D20 (September 2016) PERFORMANCE TECHNICAL SPECIFICATION SECTION D20 PLUMBING 02/18 NOTE: This section
FEATURES. Other Fed-Flush Arrangements
Brochure # 0710 TYPE TYPE... VSAF SEWAGE EJECTOR SYSTEM Flows to 600 gpm, Heads to 120, 1 thru 40 HP. Discharge size 4, 1750 and 1150 RPM, strainer in discharge pipe. HIGHLIGHTS Installations where rags
PRICE BOOK CONTENTS 010 PIPE
010 PIPE 010 Buttweld Pipe 020 ERW 2-24 Pipe 030 Domestic Seamless Pipe 2-12 040 Domestic OD Seamless 14-24 Pipe 050 Pressure Pipe A106 060 Fusion Bond Pipe 080 Cut To Order Pipe 020 STAINLESS STEEL PIPE
NYC Department of Education
Asset: AUTOMOTIVE TRADES VOC HS - K, 50 BEDFORD AVENUE, New York, 11222 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2018-05-01 8:09 AM 2018-05-10 2:18 PM Asset Data Are there fuel
SECTION WET-PIPE SPRINKLER SYSTEMS
SECTION 21 1300 S PART 1 -GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
SECTION SECTION DESIGN REQUIREMENTS
SECTION 26 09 SECTION 23 05 23 DESIGN REQUIREMENTS GENERAL DUTY VALVES GENERAL INFORMATION 1.1 This section applies to valves for hydronic and steam systems. DESIGN REQUIREMENTS 2.1 Design Criteria a.
NYC Department of Education
Asset: W.E.B. DUBOIS HS - BROOKLYN, 402 EASTERN PARKWAY, New York, 11225 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2017-12-04 1:02 PM 2017-12-27 4:16 PM Asset Data Are there fuel
HVAC BASIC MATERIAL AND METHODS 1.01 RELATED CORNELL DESIGN AND CONSTRUCTION STANDARDS
230500 HVAC BASIC MATERIAL AND METHODS PART 1 GENERAL 1.01 RELATED CORNELL DESIGN AND CONSTRUCTION STANDARDS A. Section 230000 Basic HVAC Requirements B. Section 230523 Valves C. Section 230510 Chilled
NYC Department of Education
Asset: J. K. ONASSIS HS FOR INT CAREERS-M, 120 WEST 46 STREET, New York, 10036 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2017-12-11 11:37 AM 2017-12-26 12:18 PM Asset Data Are there
2016 CDM Smith All Rights Reserved July 2016 SECTION PLUMBING - EQUIPMENT
PART 1 GENERAL 1.01 SCOPE OF WORK SECTION 22 30 00 PLUMBING - EQUIPMENT A. Furnish all labor and materials required and install the following Plumbing Equipment complete as specified herein and as shown
CALIFORNIA PLUMBING CODE MATRIX ADOPTION TABLE APPENDIX A - RECOMMENDED RULES FOR SIZING THE WATER SUPPLY SYSTEM 1 2 1/AC AC SS SS/CC
CALIFORNIA PLUMBING CODE MATRIX ADOPTION TABLE APPENDIX A - RECOMMENDED RULES FOR SIZING THE WATER SUPPLY SYSTEM Adopting Agency BSC SFM HCD DSA OSHPD CSA DPH AGR DWR CA 1 2 1/AC AC SS SS/CC 1 2 3 4 Adopt
NYC Department of Education
Asset: P.S. 161 - MANHATTAN, 499 WEST 133 STREET, New York, 10027 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2018-03-15 8:26 AM 2018-06-08 1:37 PM Asset Data Are there fuel tanks?
MLA Architects Pierz Public Schools ISD #484 Healy High School Multi-Purpose & Choir Additions Pioneer Elementary School Class Room Addition Pierz, MN
DIVISION 21 - FIRE SUPPRESSION (REFER TO SECTION 23 05 00 FOR BASIC FIRE SUPPRESSION REQUIREMENTS) 21 05 00 Common Work Results for Fire Suppression 21 13 13 Wet-Pipe Sprinkler Systems END OF SECTION FIRE
Read Only Document Not For Distribution
Chapter 14 Special Requirements For Health Care Facilities 14.1 GENERAL This Chapter applies to special fixtures and systems that occur in health care facilities and to the special plumbing requirements
DUKE UNIVERSITY DESIGN GUIDELINES
1 15480 Domestic Hot Water Systems 22 11 00 1. Introduction A. Domestic hot water systems are critical to all building types on the University campus: residential, administrative, laboratory/research,
1 Exam Prep Plumbing State Contractors Practice Exam 2
1 Exam Prep Plumbing State Contractors Practice Exam 2 1 According to Chapter 64E-6, when sizing a grease interceptor used in a restaurant, the correct formula is. A. (S) x (EW 12) x (LF) B. (S) x (GS)
PLAN REVIEW SUBMITTAL GUIDE
PLAN REVIEW SUBMITTAL GUIDE Plans, specifications and other construction documentation for the initial plan review should be as complete as possible at the time of submittal. Use this convenient guide
Mechanical/Plumbing Specification
Mechanical/Plumbing Specification Contents WC-1 Toilet 3 WC-1 Fixtures - Toilet Seat & Toilet Supply 4 UR-1 Urinal 5 UR-1 Fixtures - Metering Valve & Vacuum Breaker 7 - Wall Cleanout & Urinal Carrier 9
NYC Department of Education
Asset: P.S. 4 - MANHATTAN, 500 WEST 160TH STREET, New York, 10032 Inspection Id Inspection Type Time In Last Edited ME : Mechanical 2017-12-08 8:29 AM 2017-12-08 3:44 PM Asset Data Are there fuel tanks?
BRADLEY CORPORATION DOMESTIC WATER PIPING SPECIALTIES Page 1 of 9
BRADLEY THERMOSTATIC MIXING VALVES Bradley Corporation, a leader in the manufacture of fixtures and plumbing products, produces four lines of thermostatic mixing valves (TMVs). Bradley Navigator High-Low
DualPak Series FILE NO: DATE: Feb. 15, 1999 SUPERSEDES: DATE: Sept. 28, DualPak 6900 Series Booster System
DualPak Series 6900 FILE NO: 62.11 DATE: Feb. 15, 1999 SUPERSEDES: 62.11 DATE: Sept. 28, 1995 DualPak 6900 Series Booster System D U A L P A K 6 9 0 0 Armstrong proudly presents the Series 6900 DualPak