CTC Products for Paper & Pulp
|
|
- Samantha Carson
- 5 years ago
- Views:
Transcription
1 CTC Products for Paper & Pulp
2 CTC Products for Paper Mills Connection Technology Center, Inc Rae Boulevard Victor, New York Toll Free: (800) Phone: (585) Fax: (585) Background: Paper Mills are a unique and challenging environment! Not all sensors, cables, and connectors fit all applications. There are wet sections, hot dryer sections, and just general purpose process equipment in each paper machine that need special treatments. This is a general outline for choosing vibration analysis hardware for use in a Paper Mill. Cables and Sensors Wet Sections: Generally, in the wet end of the paper machine, the temperatures are less than 121 degrees C and the model AC192-1A (top exit) or model AC194-1A (side exit) can be used with great success while maintaining a smaller size/footprint. CB111 Teflon Yellow jacketed cable with twisted shielded pairs, braided shield, and a drain wire is preferred. It has a rugged structure and high visibility that makes it ideal in paper machines. The connector for the wet end of the paper machine should be the A2R or B2R. These IP66 connectors are made from PPS (Polyphenylene Sulfide) and provide maximum protection against caustic solutions used in the paper manufacturing process. They also make it easy for maintenance to connect and disconnect the cables during roll changes and other maintenance procedures. CB111 Cable + A2R Connector CB111 + B2R Connector Connection Technology Center, Inc. 1 September 1, 2009
3 Since both connectors are rated IP66, no lubrication or sealant should be used with either of these connectors. Install the both connectors under dry and clean conditions, by aligning the 2 pins to the 2 sockets using the keyway and for: The A2R, tighten the threaded stainless steel locking collar. To remove the connector, unthread the locking collar. The B2R, push the boot straight over the sensor connector. To remove the connector, pull it straight off the sensor. Do not use any twisting motion. Dryer Sections: In the dryer sections where temperatures range between degrees C, the AC207-1A (top exit) and AC208-1A (side exit) sensor should be used. CB111 Teflon Yellow jacketed cable with twisted shielded pairs, braided shield, and a drain wire is preferred. It has a rugged structure that makes it ideal in dryers. The connector for the dryer section of the paper machine should be the A2R or B2R. These IP66 connectors are made from PPS (Polyphenylene Sulfide) and provide maximum protection against higher temperatures used in the paper drying process. They also make it easy for maintenance to connect and disconnect the cables during roll changes and other maintenance procedures. CB111 Cable + A2R Connector CB111 + B2R Connector Connection Technology Center, Inc. 2 September 1, 2009
4 Process Equipment: The supporting process equipment (motors, fans, pumps) can use general purpose sensors and connectors. The model AC102-1A (top exit) or model AC104-1A (side exit) can be used with great success while maintaining a lower cost. CB102 Teflon red jacketed cable with twisted shielded pairs, foil shield, and a drain wire is available. It is a reliable cable for process support equipment like motors, fans, and pumps. Low cost connectors like the A2A molded polycarbonate will still offer IP66 protection and provide a solid reliable connection to the sensor. Cables and Sensors Summary: The different applications in the Paper Mill require different treatments. Each sensor, cable, and connector should be selected for functionality, durability, and cost. This will provide a successful installation for the customer. Connection Technology Center, Inc. 3 September 1, 2009
5 Enclosures: Junction box: The CTC fiberglass model SB102 series junction boxes can be used with great success while maintaining a lower cost. This enclosure is ideal offering IP66 protection for washing, while providing an interface for standard data collector cables. Please note the online system expansion jacks for use with the optional 12 position plug. Connection Technology Center, Inc. 4 September 1, 2009
6 Cable Reduction Box: Where long runs of cables are expected, the CR102 fiberglass cable reduction box and multi-conductor cables are another option available. Connection Technology Center, Inc. 5 September 1, 2009
7 In high temperature applications like the dryer sections, the CRHT102 or CRHT202 should be used for cable reduction. Connection Technology Center, Inc. 6 September 1, 2009
8 Enclosures Summary: The different applications in the Paper Mill require different treatments. Just as with the sensors and cables, each enclosure should be selected for functionality, durability, and cost. Stainless steel enclosures are also available for demanding applications. This will provide a successful installation for the customer. If you have any questions, please call CTC and ask to speak to your Regional Sales Manager for further technical assistance. Connection Technology Center, Inc. 7 September 1, 2009
9 Partial Listing of World Wide Paper Customers for CTC Abitibi Consolidated Blue Ridge Paper Bowater Mersey Carter, Holt, Harvey Cariboo Pulp & Paper Cornerbrook Pulp & Paper Domtar Georgia Pacific Inland Paperboard International Paper Irving Pulp & Paper Mead Containerboard Norske Skog Paperboard Jonquiere Proctor & Gamble Sappi Siam Cement Group Smurfit Stone Stora Enso Tembec Paper Group UPM Visy Industries Kimberly-Clark
10
Multivariate Analysis of Variables Affecting Thermal Performance of Black Liquor Evaporators
Multivariate Analysis of Variables Affecting Thermal Performance of Black Liquor Evaporators Hamideh Hajiha & Honghi Tran (University of Toronto) Odessa Websdale, Denys Holik & Bill Downing (DMI) 1 Thermal
More informationFOR TM-16 EMERGENCY WARNING SYSTEM
INSTALLATION AND INSTRUCTION MANUAL FOR TM-16 EMERGENCY WARNING SYSTEM SPECIAL NOTE BOONE CABLE WORKS & ELECTRONICS, INC. 1773-219 TH LANE P.O. BOX 429 READ THIS ENTIRE BOOKLET BOONE, IOWA 50036 USA BEFORE
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The PLT-BY Tee Splice Connection Kit is for use with all versions of Nelson Heat Tracing Systems LT, CLT, HLT and NC heater cables. Compatible for use with any vendor s heater cables small
More informationPERIOD ARTS FAN CO. Customer Service M-F 8am - 4pm (PST)
PERIOD ARTS FAN CO. Customer Service M-F 8am - 4pm (PST) (ph) 888.588.3267 www.periodarts.com Lapa Fan- Installation Instructions Should you have any questions or difficulty installing your new fan, please
More informationModel No: 56DFH-L HS-1289-C. Cover for non-light option
Owner s Manual Starfire Model No: 56DFH-L HS-1289-C Cover for non-light option These instructions contain 5 pages: Page 1: Foreword Page 2: Unpack and inspect parts contained, and pre-installation notes
More informationThermal Devices, Inc. Mount Airy, Maryland USA C D E F. Typical Maxiband Clamping
Maxiband Heaters The Most Sought After Band Heater A B Maxiband General purpose terminal box offers excellent protection to the exposed terminals. To simplify electrical wiring, the box has two 1/2" trade
More informationMEGAWAT * HIGH DENSITY CARTRIDGE HEATERS
MEGAWAT * HIGH DENSITY CARTRIDGE HEATERS MEGAWAT high-density cartridges are round tubular heaters with electrical terminations on one side. These dependable heaters are made to withstand tough industrial
More informationC Electrical Connection Kit
1548-4010C Electrical Connection Kit For Use With Dekoron 2700 and 2300 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4010C electrical connection and end seal kit
More information3SA60 3SA60+LED. Vogue & Vogue Plus. Net weight. This instruction contains 11 pages:
Vogue & Vogue Plus 3SA60 3SA60+LED This instruction contains 11 pages: Page 1: Foreword Page 2~3: Unpack and inspect parts contained Page 4~5: Notes before installation and Hanging system installation
More informationSPEC SHEET. Simple Expansion Solutions ZONE EXPANSION MODULES: SINGLE AND MULTIPLE POINT
SPEC SHEET Simple Expansion Solutions Expand your DMP panel options with a wide array of expansion modules. Add supervised Class B burglary zones. Connect non-powered burglary or fire type devices for
More informationJB-RTD-STAND RTD PIPE STAND FOR COMBINATION POWER CONNECTION BOX AND ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS
JB-RTD-STAND RTD PIPE STAND FOR COMBINATION POWER CONNECTION BOX AND ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS JB-RTD-STAND with Raychem heating cable DESCRIPTION The Raychem JB-RTD-STAND is a combination
More informationINSTALLATION & OPERATING INSTRUCTIONS
INSTALLATION & OPERATING INSTRUCTIONS WARNING RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND-FAULT CIRCUIT-INTERRUPTER. THE UNIT SHOULD BE INSTALLED BY A QUALIFIED SERVICE REPRESENTATIVE.
More informationMAKAI WIDESPREAD FAUCET INSTALLATION
SKU(s): 933814 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing,
More informationSAVE THESE INSTRUCTIONS
Built-In Dishwasher Dishwashers Write the model and serial numbers here: Model # Serial # You can find them on the tub wall just inside the door or. the lower part of back. Installation Instructions DDW1802W
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The ALT-LPM Power Connection Kit without Enclosure is constructed of cast aluminum for use with all versions of Nelson Heat Tracing Systems LT, HLT & NC heater cables. Compatible for use with
More informationTHERMAL BUILDING SOLUTIONS EN-TraceTekTTSIM1A-IM-H /16
TraceTek TTSIM-1A TraceTek Sensor Interface Module with Relay Installation/OPERATION Instructions Approvals and Certifications TYPE NM General Signaling Equipment 76LJ Only AC versions are UL listed and
More informationNELSON HEAT TRACING SYSTEMS ALT-BC STANDARD POWER CONNECTION KIT
DESCRIPTION The ALT-BC Standard Power Connection Kit is constructed of cast aluminum for use with all versions of Nelson Heat Tracing Systems LT, CLT, HLT and NC heater cables. Compatible for use with
More informationRYLE WIDESPREAD FAUCET INSTALLATION
SKU(s): 934429, 934421 RYLE WIDESPREAD FAUCET INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no
More informationIntroduction to Flow Switch
Introduction to TM Solutions Flow Detection, Switching & Control Flow switches detect a change in state from flow or no-flow within pipe or ducting. Correspondingly, the sensor inverts a contact to signal
More informationCeiling Fan Installation Instructions
OWNER S MANUAL Ceiling Fan Installation Instructions Total fan weight For 3TF24XX Series Fans READ AND SAVE THESE INSTRUCTIONS QUALITY CEILING FANS Installation 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
More informationNELSON HEAT TRACING SYSTEMS INSTALLATION
DESCRIPTION The ALT-BY Tee Splice Connection Kit is constructed of cast aluminum for use with all versions of Nelson Heat Tracing Systems LT, CLT, HLT and NC heater cables. Compatible for use with any
More informationSensor Interface Module Installation/Operation Instructions
TraceTek TTSIM-1 Sensor Interface Module Installation/Operation Instructions Approvals and Certifications TYPE NM General Signaling Equipment 76LJ Only AC versions are UL listed and VDE Certified. For
More informationLevel instruments. Point level measurement - Capacitance switches. Pointek CLS100 5/9. Overview. Configuration
Level instruments Overview Configuration is a compact 2-wire inverse frequency shift capacitance switch for level detection in constricted spaces, interfaces, solids, liquids, slurries and foam. Benefits
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The Z1-PLT-LPM Power Connection Kit is designed for terminating one heater cable to customer supplied power wiring. This kit is designed for use with all wattages of Nelson Heat Tracing Systems
More informationSWIVEL HEAD WASTE AND OVERFLOW INSTALL
SKU(s): 921385 SWIVEL HEAD WASTE AND OVERFLOW INSTALL BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts
More informationWHIRL-A-WAY OPERATIONS MANUAL
WHIRL-A-WAY OPERATIONS MANUAL www.bepressure.com BE-00WAW BE-00WAW BE-00WAW DISTRIBUTED BY BE-000WAWY BE-00WAWG BE-000WAWS BE-00WAWS " - " SET-UP PROCEDURES Thank you for purchasing a BE Whirl-A-Way. We
More informationDISHWASHER. Models DW2432 and DW2432SS. Installation Manual. Write Serial Number (on inner door of unit) here:
DISHWASHER Models DW2432 and DW2432SS Installation Manual Write Serial Number (on inner door of unit) here: Felix Storch, Inc. Summit Appliance Division 770 Garrison Avenue Bronx, New York 10474 www.summitappliance.com
More informationTTSIM-2 TRACETEK SENSOR INTERFACE MODULE WITH LCD AND RELAY INSTALLATION/OPERATION INSTRUCTIONS
TTSIM-2 TRACETEK SENSOR INTERFACE MODULE WITH LCD AND RELAY INSTALLATION/OPERATION INSTRUCTIONS GENERAL INFORMATION Please read these instructions and keep them in a safe place. These instructions must
More informationInstallation Instructions
GE Consumer & Industrial Appliances Installation Instructions Junction Box Cover Within this user bag, you will find a junction box cover and a #10 hex head screw used to attach the junction box cover
More informationLevel Measurement. Point level measurement Capacitance switches. Pointek CLS100. Overview. Configuration
Level Measurement Siemens AG 2012 Overview Configuration Installation Standpipes 0 (2) 20 (0.79) max. is a compact 2-wire inverse frequency shift capacitance switch for level detection in constricted spaces,
More information5WF42XX Series Fan UL Model No. : AC-542OD. Owner s Guide and Installation Manual
Owner s Guide and Installation Manual 5WF42XX Series Fan UL Model No. : AC-542OD Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER
More informationBAND HEATERS component parts
BAND HEATERS w w w.wat tco.com OVERVIEW WATTCO band heaters are the ideal solution for high watt densities and high operating temperature applications, especially for the plastics industry. The various
More informationPotts Welding & Boiler Repair Co., Inc.
Potts Welding & Co., Inc. Welcome Potts Welding was founded by Walter Potts in 1929 as a boiler repair business. It was incorporated in 1965 in the state of Delaware and operated essentially unchanged
More informationTECK-40 Series 1000V Class Splice for 4/C Armored Teck Power Cables
Product Installation Instructions TECK-0 Series 000V Class Splice for /C Armored Teck Power Cables Raychem Tyco Electronics - Energy 8000 Purfoy Road Fuquay-Varina, NC 756 PII-598 Rev AC The following
More informationLevel Measurement. Point level measurement - Capacitance switches. Pointek CLS100. 5/10 Siemens FI Overview.
Siemens AG 00 Overview Configuration Installation Standpipes 0 () 0 (0.79) max. Wall Restriction is a compact -wire inverse frequency shift capacitance switch for level detection in constricted spaces,
More informationRESIN FREESTANDING TUB
RESIN FREESTANDING TUB INSTALLATION INSTRUCTIONS AND CARE GUIDE CONTENTS Tub Installation...2 Rough-In...2 Drain Installation...3 Air Tub Installation...4 Electrical Installation...4 Remote Control Installation...5
More informationARIN THERMOSTATIC SHOWER SYSTEM
ARIN THERMOSTATIC SHOWER SYSTEM INSTALLATION INSTRUCTIONS Before installing, read entire shower system installation instructions. Observe all local building and safety codes. For the following installation
More informationMICRO SWITCH Limit Switches Line Guide
MICRO SWITCH Line Guide Limitless leadership. Available with a variety of actuators, electrical specifications, terminations, circuitries and sealing ratings, Honeywell Sensing and Control s (S&C) limit
More informationDETAIL SPECIFICATION
INCH-POUND MIL-DTL-38999M 11 February 2015 DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, OR BREECH COUPLING), ENVIRONMENT RESISTANT
More informationREAD AND SAVE THESE INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS CEILING FAN INSTALLATION AND OPERATION INSTRUCTION FAN RATING AC 120V. 60Hz UL LISTED MODEL: AC-552OD WEIGHT OF FAN: 6.82 KGS 1. TOOLS AND MATERIALS REQUIRED Philips screw
More informationA B A B4
TM TM SERVICE INSTRUCTIONS Thermo-Aire Heater Kits and Air-Heater Assemblies 383808-A4 383808-B4 383880-A4 383880-B4 DESCRIPTION The Thermo-Aire Heater is used in situations where oils of heavier viscosity
More informationINSTALLATION OF DURAVENT POLYPRO SINGLE WALL POLYPROPYLENE VENTING SYSTEMS
SUPPLEMENT VENTING INSTRUCTIONS FOR INSTALLATION AND OPERATION INSTRUCTION MANUALS FOR THE FOLLOWING PRODUCT TYPES: HIGH EFFICIENCY CONDENSING COMMERCIAL, COMMERCIAL POWER DIRECT VENT, LIGHT DUTY COMMERCIAL
More informationInstruction Manual April sitrans AS 100
Instruction Manual April 2005 sitrans AS 100 Safety Guidelines: Warning notices must be observed to ensure personal safety as well as that of others, and to protect the product and the connected equipment.
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The PLT-L Series End of Circuit Light Kit is for use with all versions of LT, CLT, HLT and NC heater cables. Compatible for use with any vendor s heater cables smaller than 11mm (.44 ) diameter.
More informationDATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER ADDRESS:
Owner s Guide and Installation Manual 3TF24XX Series Fan UL Model No. : AC-536 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER
More informationPage. 1-2 Sepra-Lite Integral Optic Level Switches. 3-5 Electro Optic Level Systems: Probe and Controller
Order from: C A Briggs Company 622 Mary Street; Suite 101; Warminster, PA 18974 Phone: 267-673-8117-800-352-6265; Fax: 267-673-8118 Sales@cabriggs.com - www.cabriggs.com Page 1-2 Sepra-Lite Integral Optic
More informationedry Model Based Paper Machine Drying Optimization
Model Based Paper Machine Drying Optimization www.automationx.com www.procsim.eu Agenda Company Presentation The Energy used in Paper Making Potentials for Dryer Steam Reduction edry Solution ( How it
More informationTTSIM-1A. TraceTek Sensor Interface Module with Relay. Installation/Operation Instructions. Installation Items (not supplied) Tools Required.
TTSIM-1A TraceTek Sensor Interface Module with Relay Installation Items (not supplied) General Information Installation/Operation Instructions Please read these instructions and keep them in a safe place.
More informationStep 1: Identify the parts of your shade (parts shown are not to scale)
Motor Operated Solar Shade with Valance Installation and Care Instructions Read carefully and retain for future use. Installation video is available online. Tools required: Philips head screwdriver (not
More informationInstallation Instructions
Installation Instructions Built-In Dishwasher If you have questions, call 800-GECARES or visit our website at: www.geappliances.com BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT
More informationFireSystems PROTECTOWIRE. Installing Protectowire Linear Heat Detector
PROTECTOWIRE FireSystems Installing 1. Purpose The purpose of this guide is to ensure coverage of the area to be protected in accordance with accepted fire protection principles and to assure uniform installations.
More informationLifetime Limited Warranty
Hampton Bay Lifetime Limited Warranty The retailer warrants the fan motor to be free from defects in workmanship and material present at time of shipment from the factory for a lifetime after the date
More informationcommercial-type cabling and connectivity products into the industrial landscape.
Product Bulletin PB 315 Belden DataTuff Industrial Ethernet Connectivity, Tools & Accessories Belden DataTuff Cat 6 and 5e IP67/IP20 Cord Sets, IP67 Modular Jacks, IP67 Plug Kits, Cabling Accessories and
More informationDELEVINGNE WIDESPREAD FAUCET INSTALLATION
SKU(s): 927254 BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability for any damage to the faucet, plumbing,
More informationNELSON HEAT TRACING SYSTEMS
DESCRIPTION The SLT-LPS Entry Seal Kit provides a watertight entry into a junction box suitable for this application. This kit includes cable seals for power and end terminations. The SLT-LPS kit is designed
More informationUSB CONNECTORS MINI USB CONNECTOR & CABLE ESB3,4,5 SERIES. USB CONNECTOR & CABLE ESB0 SERIES (Connector) ESB1 SERIES (Cable)
USB CONNECTORS USB CONNECTORS MINI USB CONNECTOR & CABLE ESB3,4,5 SERIES USB CONNECTOR & CABLE ESB0 SERIES (Connector) ESB1 SERIES (Cable) IEEE1394 CONNECTOR & CABLE ESB6 SERIES (Connector) ESB2 SERIES
More informationF AN-ASPIRATED RADIATION SHIELD
F AN-ASPIRATED RADIATION SHIELD I NSTALLATION MANUAL (For all models with Mfg. Code beginning with B or higher) The Fan-Aspirated Radiation Shield uses fan aspiration and passive shielding to minimize
More informationCEILING FAN OWNER S MANUAL
CEILING FAN OWNER S MANUAL VERA CRUZ 5/04 GENERAL INSTALLATION & OPERATION INSTRUCTIONS IMPORTANT SAFEGUARDS: 1. To ensure the success of the installation, be sure to read the instructions and review the
More informationDuct and Rough Service Carbon Monoxide Sensor
Product Identification and Overview Duct and Rough Service Carbon Monoxide Sensor BAPI s Carbon Monoxide Sensor offers enhanced electrochemical sensing with outstanding accuracy at low concentrations.
More informationThe Clark-Reliance Corporation TWIP System Installation and Maintenance Instructions - Form E112 -
The Clark-Reliance Corporation TWIP System Installation and Maintenance Instructions - Form E112 - Table of Contents A. Installation Page 2 B. Interwiring Control Unit Options Page 3 C. Operation Page
More informationCeiling Fan Installation Instructions
OWNER S MANUAL Ceiling Fan Installation Instructions For 5SH54XXD-L Series Fans READ AND SAVE THESE INSTRUCTIONS Total fan weight with light kit 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
More informationInstallation Instructions
www.aquanta.io Aquanta by Sunnovations Inc. www.sunnovations.com Installation Instructions For online instructions go to: https://portal.aquanta.io/setup 1 Tools Needed: Phillips screw driver Flathead
More informationDishwasher Installation Instructions DW 24XT/DW 24XV
Dishwasher Installation Instructions DW 24XT/DW 24XV Installation Instructions Dishwasher BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT Observe all governing codes and ordinances.
More informationMarley X7 Fan USER MANUAL DESIGNED FOR INDUCED-DRAFT COOLING TOWER APPLICATIONS
USER MANUAL Marley X7 Fan DESIGNED FOR INDUCED-DRAFT COOLING TOWER APPLICATIONS M2010-1234A ISSUED 3/2012 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. Fan Components 1
More informationCeiling Fan Installation Instructions
OWNER S MANUAL Ceiling Fan Installation Instructions Total fan weight For 5SKR52XXD Series Fans READ AND SAVE THESE INSTRUCTIONS QUALITY CEILING FANS Installation SAFETY TIPS WARNING: TO REDUCE THE RISK
More informationInstallation Instructions. For the 18 Built-In Dishwasher and Front Color Panels
Installation Instructions For the 18 Built-In Dishwasher and Front Color Panels Printed in USA 154232102 Before You Begin DO NOT INSTALL DISHWASHER UNTIL YOU HAVE READ ALL INSTRUCTIONS. FOR YOUR SAFETY,
More informationHot water temperature maintenance. Less water volume and less heat loss in the pipe work help prevent bacteriological
Providing the comfort of instant hot water is the key requirement of any modern hot water system. The Raychem single-pipe system keeps water at the right temperature in a building s water distribution
More information5DI52XXD/5DI52XXD-L Series Fan UL Model No. : 5DI52. Owner s Guide and Installation Manual
Owner s Guide and Installation Manual 5DI52XXD/5DI52XXD-L Series Fan UL Model No. : 5DI52 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER:
More informationGlendale 52 in Ceiling Fan Owner's Manual. Glendale Ventilador de Techo de 1.32 m Manual del Propietario
Glendale 52 in Ceiling Fan Owner's Manual Glendale Ventilador de Techo de 1.32 m Manual del Propietario Hampton Bay Lifetime Motor Warranty The retailer warrants the fan motor to be free from defects in
More informationCartridge Heaters. Metric FIREROD Cartridge. Applications and Technical Data
W A T L O W The Watlow FIREROD not only set the industry standard for cartridge heaters, it continues making improvements in construction and design. Among those improvements is the metric FIREROD, a variation
More informationThermoCable Linear Heat Detection System
ThermoCable Linear Heat Detection System Estimating Guide 1. INTRODUCTION 1.1 Linear Heat Detection ThermoCable digital linear heat detection wire is a combination of advanced polymer and digital technologies
More information5SLR52XXD-B Series Fan UL Model No. : 5SLR52. Owner s Guide and Installation Manual
Owner s Guide and Installation Manual 5SLR52XXD-B Series Fan UL Model No. : 5SLR52 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER:
More information5CO52XX Series Fan UL Model No. : 5CO52. Owner s Guide and Installation Manual. Attach sales receipt to this card and retain as your proof of purchase
Owner s Guide and Installation Manual 5CO52XX Series Fan UL Model No. : 5CO52 Attach sales receipt to this card and retain as your proof of purchase DATE OF PURCHASE: RETAILER NAME: MODEL NUMBER: RETAILER
More informationJBS-100-ECP-A COMBINATION POWER CONNECTION BOX AND DIGITAL ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS
JBS-100-ECP-A COMBINATION POWER CONNECTION BOX AND DIGITAL ELECTRONIC CONTROLLER INSTALLATION INSTRUCTIONS JBS-100-ECP-A with Pyrotenax MI heating cable using required MI cable grounding kit JBS-100-ECP-A
More informationSmart Water Heater Controller
Smart Water Heater Controller Installation Instructions Version 1.0 2016 1 Introduction Congratulations on the purchase of your Aquanta Smart Water Heater Controller! The Aquanta retrofittable water heater
More informationBuilt-In Dishwasher. Installation Instructions. BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT The dishwasher MUST be
Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com BEFORE YOU BEGIN Read these instructions completely and carefully.
More informationDPM-G DPM-CR DPM-W DPM-B INDOOR DOME PENDANT MOUNT INSTALLATION MANUAL
DPM-G DPM-CR DPM-W DPM-B INDOOR DOME PENDANT MOUNT INSTALLATION MANUAL MANUAL NUMBERS 517646-1960 517645-1960 517702-1960 517783-1960 Ultrak, Inc. 4465 Coonpath Road NW Carroll, OH 43112 (740) 756-9222
More informationCELEBRITY DELUXE 52" indoor fans
CELEBRITY DELUXE 52" indoor fans Ceiling Fan Installation Instructions For item numbers: 1535-01 1535-02 1535-07 1535-09 1535-15 1535-26 1535-61 1535-83 1535-85 1535-713 1535-962 READ AND SAVE THESE INSTRUCTIONS
More informationAlarmLine Addressable Linear Heat Detector
Line Addressable Linear Heat Detector P/N 7-0001-00 Effective: March 2008 K-7-02 FEATURES UL Listed FM Approved CSFM MEA (pending) Low-cost interface between Line sensor cable and control panel accepting
More informationMMEngineering. Suction lifter. Lightning fast suction for lifting and moving. with only on vaccum line. Suction lifters Vacuum-operated
6 available sizes Integral suction lifter Accessories Lightning fast suction for lifting and moving with only on vaccum line s Vacuum-operated Integral suction lifter Compressed-air Page 3-01.. Page 3-02..
More informationTHE ART OF OUTDOOR ILLUMINATION
THE ART OF OUTDOOR ILLUMINATION Sollos Landscape Lighting was born out of an unmet need in the marketplace for a line of architectural fixtures designed to operate retrofit LED lamps. As a Halco Lighting
More informationDräger Polytron Pulsar 2 Open Path Gas Detector
Dräger Polytron Pulsar 2 Open Path Gas Detector The Dräger Polytron Pulsar 2 represents the latest infrared technology in open path gas detection. Equipped with all the same functions as the standard Dräger
More informationModel: DC-159. Instruction Manual
Model: DC-159 Instruction Manual Attention: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge
More informationInstallation Instructions
Installation Instructions Built-In Dishwasher If you have questions, call 800-944-9400(US),800-245-8352(Canada)or visit our website at: www.frigidaire.com BEFORE YOU BEGIN Read these instructions completely
More informationDirect Exhaust Venting Kit Instructions
CONDENSING GAS BOILER 220/299/300/399 Direct Exhaust Venting Kit Instructions Evergreen 220/299/300/399 Kit part number 383-500-769 STOP! Read before proceeding Hazard definitions The following defined
More informationPrinted Circuit Board Connectors
Printed Circuit Board Overview Printed circuit board or PCB connectors are heavy duty environmentally sealed connectors designed for wire-to-circuit board connections. TE Connectivity Industrial & Commercial
More informationGreentrol Automation, Inc.
Model GA-100 Technical Manual GreenAlert 100 Series Greentrol Automation, Inc. Installation, Operation and Maintenance Technical Manual GA-100 Document Name: TM_GA-100_R1C TM_GA-100_R1C Part Number: 960--0000
More informationMaxGard. Interconnection Systems. Durability. Performance. Safety
8Russellstoll Pin and Sleeve Power Connectors Safety Different power supply ratings can t mix: 24 single-rate device polarizations ensure exact voltage, frequency and phase differentiation Safe connections:
More informationDETAIL SPECIFICATION
INCH - POUND MIL-DTL-38999L 10 May 2012 SUPERSEDING SUPPLEMENT 1 30 May 2008 DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH
More informationCEILING FAN OWNER'S MANUAL
Style that revolves around you. CEILING FAN OWNER'S MANUAL CIARA 12/14 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. GENERAL INSTALLATION & OPERATION
More informationCBT Bowl & wrap replacement
CBT bowl & wrap replacement 2 CBT BOWL & WRAP REPLACEMENT Revision History rev. level 01_03.14.2012 rev. level 02_03.19.2012 rev. level 03_03.23.2012 rev. level 04_05.30.2013 NOTE: due to the fact that
More informationHMN-D2 Insert Series
HMN-D2 Insert Series Table of contents 1. SCOPE... 2 1.1. Content... 2 1.2. Qualification... 2 2. APPLICABLE DOCUMENTS... 2 2.1. TE Connectivity Documents... 2 2.2. Other Documents... 2 3. REQUIREMENTS...
More informationCEILING FAN OWNER'S MANUAL
Style that revolves around you. CEILING FAN OWNER'S MANUAL QUATRO 10/09 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. GENERAL INSTALLATION & OPERATION
More informationINSTALLATION INSTRUCTIONS Model FH-2071-UM Enclosure
INSTALLATION INSTRUCTIONS Model FH-2071-UM Enclosure Enclosure INTRODUCTION The Model FH-2071-UM Enclosure from., used in Marine applications is robust and weather-resistant. Its durable design is customized
More information50 Disassembly and assembly Cab and its attachments
When adjustment is needed after performing check in step 8; 3) Close front window assembly (1). 4) Loosen locknuts (26) of right and left rubber stoppers (24) and move the stoppers backward so that front
More informationCEILING FAN OWNER S MANUAL
CEILING FAN OWNER S MANUAL LX SERIES 5/04 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout. GENERAL INSTALLATION & OPERATION INSTRUCTIONS IMPORTANT
More informationYELLOW JACKET. H 2 Tracer Gas Leak Detector. Operations Manual. Detects 5% H 2 in 95% Nitrogen Tracer Gas. Model 69341
YELLOW JACKET H 2 Tracer Gas Leak Detector Model 69341 Detects 5% H 2 in 95% Nitrogen Tracer Gas Operations Manual 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit
More informationConcepts Serving Systems
Concepts Serving Systems Installation Manual Please read this manual completely before attempting to install or operate this equipment! Notify carrier of damage! Inspect all components immediately. February
More informationSilverware Pre-washing System INSTALLATION
Silverware Pre-washing System INSTALLATION 1 WARNING! Be sure to follow all applicable national and local electrical codes when installing the electrical supply for this system. All field connections must
More information30-YEAR LIMITED WARRANTY
PROGRESS LIGHTING 30-YEAR LIMITED WARRANTY PROGRESS LIGHTING FAN MOTORS ARE WARRANTED TO THE END USER TO BE FREE OF ELECTRICAL AND/OR MECHANICAL DEFECTS FOR A PERIOD OF 30 (THIRTY) YEARS FROM DATE OF SALE.
More information