JDPC.002 Jaga Dynamic Product Controller

Transcription

1 JDPC.00 Jaga Dynamic Product Controller JDPC.00 per unit, otherwise the warranty is no longer valid. Installation / user guide Jaga Dynamic Product Controller Clima Canal Please read these user instructions carefully to ensure crect use of the product.

2 Clima Canal JDPC.CC4 / JDPC.CC Dynamic Product Controller, heating, heating and cooling. With water-temperature sens With -modes control panel Basic settings Connecting Basic settings JDPC.00: 467 Configuration Code: see the product label on the device Ι Not connected Ι RED +4V Ι BLUE -4V Heating: JDPC.CC4 and Heating and cooling: JDPC.CC Setup and operation The module is facty assembled and tested accding to the product configuration. Basic settings water temperature set point: Fan start when supply water T > 8 C Setup and operation The module is facty assembled and tested accding to the product configuration. Basic settings water temperature set point: Fan start when supply water T > 8 C Fan start when supply water T < 8 C Manually adjusting settings: fan speed water temperature set point Pag. Table : fan speed Table : adjusting min. water temperature heating Manually adjusting settings: Pag. Table : fan speed fan speed water temperature set point Table : adjusting min. water temperature heating Table : adjusting max. water temperature cooling With control panel: Fan speed Speed Speed Speed %: Speed Speed Speed Speed %: Speed Fan speed facty settings I - (MIN) The blue LED blinks fast + I The red LED blinks fast (MAX) the Fan speed: sht press - + to adjust the speed of the mot(s). after the adjustment of the speed, the fans will run f 0 in der to control, irrespective of the water temperature. The water-temperature sens will not respond during this time. Any modification will be automatically sted in the internal (EE PROM) memy !! The JDPC controller returns back into nmal mode after 0 and will automatically save all modified settings!! 467

3 Clima Canal JDPC.CC4 Dynamic Product Controller, heating Put the controller in the desired mode with the control panel Press button until the desired mode is reached (± sec.) sec verwarmen chauffer Heizung heating sec sec uit éteinte Aus off How to use Speed Speed Speed Water temperature < Adjusted temperature: Leds flashing every Leds flashing every Clima Canal JDPC.CC Dynamic Product Controller, heating and cooling Put the controller in the desired mode with the control panel Mode / Press button until the desired mode is reached (± sec.) /BOOST / COMFORT / BOOST / verwarmen chauffer Heizung heating When AUTO CHANGE OVER mode the controller itself will select the desired operation mode. The user can always choose MANUALLY a different mode of operation. /BOOST / COMFORT / BOOST / uit éteinte Aus off koelen rafrâichir kühlen cooling /BOOST / COMFORT / BOOST / How to use Speed Speed Speed Water temperature < Adjusted temperature: Leds flashing every Leds flashing every Speed Speed How to use Speed Water temperature > Adjusted temperature: Leds flashing every Leds flashing every

4 Clima Canal JDPC.CC7 / JDPC.CC7 Dynamic Product Controller, heating, heating and cooling. Controlled with external 0-0V control signal With water-temperature sens With -modes control panel Basic settings Connecting Basic settings JDPC.00: Fan Speed Configuration Code: see the product label on the device Ι 0-0V analog in BLUE -4V RED +4V Max Min V 0V Analog in Heating: JDPC.CC7 and Heating and cooling: JDPC.CC7 Setup and operation The module is facty assembled and tested accding to the product configuration. Basic settings water temperature set point: Fan start when supply water T > 8 C Setup and operation The module is facty assembled and tested accding to the product configuration. Basic settings water temperature set point: Fan start when supply water T > 8 C Fan start when supply water T < 8 C Manually adjusting settings: Pag. Tabel : fan speed fan speed Manually adjusting settings: Pag. Table : fan speed fan speed water temperature set point Table : adjusting min. water temperature heating water temperature set point Table : adjusting min. water temperature heating Table : adjusting max. water temperature cooling 4

5 Clima Canal JDPC.00 Dynamic Product Controller: Table / / Fan speed SPEED %: I - + I (MIN) The blue LED blinks fast The red LED blinks fast (MAX) the Fan speed: sht press - + to adjust the speed of the mot(s). after the adjustment of the speed, the fans will run f 0 in der to control, irrespective of the water temperature. The water-temperature sens will not respond during this time (position, 4, 6 7). Any modification will be automatically sted in the internal (EE PROM) memy. 467 Setting the water temperature Setting the minimum water temperature heating (default =>8 C) A Setting temperature C 4 C 6 C 8 C 0 C C 4 C 6 C 8 C B C I - C + C I Press and hold the (+) button until the red LED flashes times. Increasing temperature Briefly press (+): the temperature increases by one step C. If the maximum temperature is reached, the red LED flashes rapidly. Decrease temperature Briefly press (-): the temperature decreases by one step C. If the minimum temperature is reached, the blue LED will flash rapidly. After 0, the JDPC module returns to nmal mode. Exit setup mode by holding the + button until the red LED blinks x. 467 Automatic control: The green LED lights when the water temperature exceeds the set temperature. This indicates that the supply water is hot. Each adjustment is sted in the internal (EE PROM) memy. 467 x x Setting the maximum temperature of cooling water (default = <8 C) A Setting temperature C C 4 C 6 C 8 C 0 C C 4 C 6 C 467 I - C + C I x B C Press and hold the (+) button until the blue LED flashes times. Increasing temperature Automatic control: Briefly press (+): the temperature increases by one step C. The green LED lights when the water temperature is lower than the If the maximum temperature is reached, the red LED flashes set temperature. This indicates that the supply water temperature rapidly. is colder. Decrease temperature Each adjustment is sted in the internal (EE PROM) memy. Briefly press (-): the temperature decreases by one step C. If the minimum temperature is reached, the blue LED will flash rapidly. After 0, the JDPC module returns to nmal mode. Exit setup mode by holding the + button until the blue LED blinks x. 467 x!! The JDPC controller returns into nmal mode after 0 and will automatically save all modified settings!! default facty temperature setting

6 Clima Canal JDPC.00 Dynamic Product Controller: Reset to Facty Default Reset to Facty Default. Turn off power press and hold both - and + buttons simultaneously.. Turn power on. Press and hold both - and + buttons simultaneously until the blue LED light is blinking. After the green LED will light and then after 4, the red LED.. The controller will return to Facty Default settings, all LEDs will flash f 8 ATTENTION: Doing so will erase all of the data, settings, and applications and reset the controller to the iginal facty settings!! Warning: This product is not intended f use by persons (including children) with reduced physical, sensy mental capabilities, lack of experience and knowledge, unless they have been given supervision instruction concerning use of the appliance by a person responsible f their safety. Children should be supervised to ensure that they do not play with the product. Please follow these instructions carefully in der to allow f an err-free installation and a carefree use. Entitlement to warranty is cancelled in case of: errs damage resulting from not following the assembly, cleaning user instructions supplied by the manufacturer, wrong, improper and/ irresponsible use treatment of the device, wrong incompetent repairs and defects due to external facts, self-applied changes to the device. equipment that is built in, in a way that it cannot be reached nmally. If you have any questions complaints, please contact your supplier installer. The copyright of these instructions is the property of the company Jaga International juli 7, 07 4:0 PM - Jaga N.V. 6

7 Notes 7

8 Jaga N.V. Verbindingslaan 6 B-90 Diepenbeek Tel.: + (0) info@jaga.be juli 7, 07 4:0 PM - Jaga N.V.