Lab Spaces. Laboratory Planning Solutions

Transcription

1 Lab Spaces Laboratory Planning Solutions UniLine Laboratory Casework Countertops / Worksurfaces UniFlow Laboratory Fume Hood Laboratory Ventilation Systems Emergency Drench Shower Eye Wash Booths Modular Clean Labs EnviroMax Vented Enclosures HEMCOR ISO 9001:2008 Certified Company

2 Welcome to HEMCO HEMCO a leading manufacturer of innovative laboratory equipment serving the Sciences and R&D Technology Industries since HEMCO an ISO 9001:2008 Certified Company Located in Independence, Missouri, the heart of America and the crossroads of North America a major center for transportation, communication, distribution, and manufacturing industries worldwide. de. HEMCO s modern manufacturing and distribution facilities combined with our extensive engineering, design, and manufacturing capabilities are the solution for your Laboratory Planning requirements.. Independence Missouri Made in the U.S.A. Scan the Code to Visit Asia North America Europe Australia South America Africa Call (800) info@hemcocorp.com Visit: 2

3 Laboratory Planning Solutions by HEMCO Table of Contents Welcome to HEMCO...2 Section I: Laboratory Furniture Tops & Services Groupings Plan A Lab / Casework Construction...7 Acid Cabinets...8 Laboratory Cabinets Countertops & Sinks...10 Plumbing, Electrical, & Safety...11 Section II: Fume Hoods & Accessories UniFlow SE AireStream...12 UniFlow SE Fume Hood...14 UniFlow LE AireStream...16 UniFlow CE AireStream...18 UniFlow FM Walk-In Fume Hood...20 Plan-A-Hood...22 Fume Hood Worksurfaces...23 Fume Hood Plumbing Fixtures...24 Fume Hood Electrical Services...25 Fume Hood Sinks & Plumbing...26 Apparatus Grids & Fire Extinguishers...27 Section III: Laboratory Ventilation Recommendations Lab Ventilation Recommendations...28 Energy Savings Recommendations...29 Ventilation and Duct Design...30 Fume Hood Ductwork...31 Fume Hood Blowers...32 InLine Filtration...33 Canopy Hoods...34 Lab Emergency Safety Showers...35 Section IV: Modular Clean Lab / EnviroMax Modular Clean Labs EnviroMax Vented Enclosures

4 UniLine Casework Groupings Unitized design incorporates our most popular casework groupings to meet your laboratory needs. Welded steel with chemical resistant, epoxy powder coat finish, and 1 thick phenolic resin countertops, 4 high backsplashes, and flush ends standard. ADA and sitting height options are available. Standard color: silver gray Atlantis Grouping UniLine Atlantis Grouping provides basic lab storage & a versatile work area. Cabinet grouping includes 3 standing height cabinets with rear filler panels on both ends, phenolic resin worksurface 36 high, with 4 high back splash. Includes 16 X 12 X 8 sink and H/C gooseneck faucet. Atlantis Cabinet Grouping Length Depth 30 Depth Enterprise Grouping UniLine Enterprise Grouping provides a convenient balance of storage and work space. Cabinet grouping includes 3 standing height cabinets with rear fi ller panels, 2 wall cabinets, phenolic resin worksurface 36 high, with 4 high back splash. Includes 16 X 12 X 8 sink and H/C gooseneck faucet. Lay out a Lab Space see page 7. Enterprise Cabinet Grouping Length Depth 30 Depth Endeavour Island Grouping UniLine Endeavour Grouping is a fl exible design that can serve as an island or peninsula layout. Cabinet grouping includes either 3 or 7 standing height cabinets with front and end fi ller panels, phenolic resin worksurface, and center island reagent shelf with pedestals and phenolic resin shelf. Includes 16 X 12 X 8 sink, pegboard and H/C gooseneck faucet. Lay out a Lab Space see page 7. Endeavor Cabinet Grouping Length Made In The U.S.A. 2 Length 9, 10, 12 Length 9, 10, Length 8 5, 11 5, Corner Canopy Table Grouping & Corner Canopy Casework Grouping UniLine Corner Grouping utilizes wasted corner space with storage and a corner canopy hood. Grouping includes either an angled corner cabinet with (2) single door cabinets or a corner table with a corner canopy hood. Lay out a Lab Space see page 7. 4 Corner Canopy Table Grouping Corner Canopy Casework Grouping Length Corner Canopy Table Grouping See page Corner Canopy Casework Grouping See page

5 UniLine Casework Groupings Unitized design incorporates our most popular casework groupings to meet your laboratory needs. Welded steel with chemical resistant, epoxy powder coat finish, and 1 thick phenolic resin countertops, 4 high backsplashes, and flush ends standard. ADA height 34 Max, and sitting height 28, options are available. Standard color: silver beige For ADA technical information, including dimensions and standards, visit: Pioneer Grouping UniLine Pioneer Grouping combines typical lab storage and a fume hood. Cabinet grouping includes (4) 36 high cabinets, phenolic resin worksurface, with 4 high back splash. Includes 16 X 12 X 8 sink and H/C gooseneck faucet. UniFlow CE included on 24 deep models in widths of 36 & 48. Lay out a Lab Space see page 7 Pioneer Cabinet Grouping Length Depth Includes CE hood Made In The U.S.A. 2 3 Length 12, 16 4 Voyager Grouping UniLine Voyager Grouping combines typical lab storage and a fume hood. Cabinet grouping includes (4) 36 high cabinets with rear filler panels on both ends, phenolic resin worksurface, with 4 high back splash. Includes 16 X 12 X 8 sink, H/C gooseneck faucet and pegboard. UniFlow LE Fume Hood included on 30 deep models in widths of 36 & 48. Lay out a Lab Space see page 7 Voyager Cabinet Grouping 30 Depth Length Includes LE hood Length 9,12, 16 Apollo Grouping UniLine Apollo Grouping combines typical lab storage and a fume hood. Cabinet grouping includes (4) 36 high cabinets with rear filler panels on both ends, phenolic resin worksurface, with 4 high back splash. Includes 16 X 12 X 8 sink, H/C gooseneck faucet and pegboard. UniFlow SE AireStream Fume Hood included on 30 deep models in widths of 48 & 72. Lay out a Lab Space see page 7 Apollo Cabinet Grouping Length Depth Includes SE AireStream hood Length 12,13,16,18 3 Mariner Grouping UniLine Mariner Grouping accommodates larger procedures in the FM fl oor mount fume hood combined with convenient cabinet storage. Grouping includes (3) cabinets 36 high, phenolic resin worksurface with 4 high backsplash, 16 X 12 X 8 sink, H/C gooseneck faucet and pegboard. UniFlow FM included 72 wide. Lay out a Lab Space see page 7 Mariner Cabinet Grouping Length Depth Length 15,

6 UniLine Casework Groupings Viking/Magellan Grouping UniLine Viking Grouping is ideal for medical examination rooms and small lab requirements. Cabinet grouping includes 1 or 2 standing height cabinets, 1 or 2 wall cabinets, phenolic resin worksurface. Includes 16 X 12 X 8 sink and H/C gooseneck faucet. Lay out a Lab Space see page 7. Viking Cabinet Grouping Length Depth 30 Depth Magellan Cabinet Grouping Width 1 24 Depth 30 Depth Made In The U.S.A. Standard Color: silver beige Length 4, 5, 6, 8 24 or 30 Depth Available 30 Length 3, 4 Gemini Grouping UniLine Gemini grouping features a sitting height desk area that can be incorporated with any of the HEMCO groupings. Cabinet grouping includes 1 sitting height fi le drawer cabinet with rear fi ller panels, single drawer apron, and phenolic resin worksurface. Sitting height 28. Lay out a Lab Space see page Length Depth 30 Depth Length 54, or 30 Depth Available Example of (7) Gemini Groupings ADA Freedom (ADA) Grouping Option When ADA requirements are necessary, the UniLine Freedom Grouping option allows you specify any HEMCO casework grouping and be compliant to all dimension, space, and access standards as specifi ed by ADA. In addition, all electrical services, plumbing accessories and safety equipment including emergency showers and eye wash stations are designed to meet ADA guidelines. Counter top height is 34. For ADA recommended reach see diagram 1 and 2. Simply add ADA as a suffi x to any HEMCO part number and HEMCO can design, quote, and supply ADA compliant equipment. Proper planning eliminates/reduces future problems. For a complete guide for all ADA technical information, including dimensions and standards, please visit: 24 Diagram #1 Reach In Corner Casework Solutions Diagram #2 Reach Over HEMCO corner cabinets and fillers offer several means by which HEMCO casework groupings or individual cabinets can be connected at a corner Max 34 Max Max 46 Max Basic Corner Scribe Overlap Corner Cabinet Spacious Corner Cabinet 71901

7 HEMCO Plan-A-Lab Worksheet showing Groupings The HEMCO Plan-A-Lab enables you to conveniently lay out your lab furniture and your pre-engineered modular clean lab structure to enclose and regulate the lab work area. Existing Walls A Basic Corner Scribe page 6 Voyager Grouping page 5 Gemini Grouping page 6 Emergency Shower page 35 UniFlow Fume Hoods pages UniFlow Fume Hoods pages Canopy Hood page X 6-8 Door Endeavor Grouping page 4 Worksurfaces page 12 Modular Clean Labs pages Easily Lay Out a Complete Lab 54 B 3-0 X 6-8 Door 108 Atlantis Grouping page 4 Gemini 30 Grouping page 6 UniFlow Fume Hoods pages Enterprise Grouping page 4 Corner Cabinet page C For Lab Planning worksheet visit: shown above 20 X 24 (2) wall system Laboratory Grade Casework & Cabinet Construction (SEFA 8 Compliant) UniLine Casework & Cabinets are constructed of welded 18 gauge steel. Base cabinets have a load capacity of 500 pounds per linear foot. Powder coat finish is environment friendly, attractive and long lasting, color: silver beige. UniLine casework, quality & style for your laboratory. Casework is tested independently to be SEFA 8 compliant. R Scientific Equipment and Furniture Association Drawers extend to 18 full open, Interchangeable, interlocking drawer head, sound deadened for quiet operation. One piece drawer body with radiused bottom for easy cleaning. 150 pound dynamic drawer slide assembly mounted on welded channel assemblies. Interior is powder coated steel, stainless steel interior is optional. Doors Two-piece double wall construction painted before assembly. Insulated door filler for added rigidity and quiet operation. Rubber door bumpers. Powder coated finish / Rear Filler Panel Cabinet shown (page 8) Cabinet Interior Minimal holes in front post for aesthetically pleasing appearance. Hem and flatten door. Adjustable shelves heavy duty stop for secure closure. Full length & width adjustable shelf for maximum storage. Unique triangular support rails for added strength. Heavy duty plated steel shelf clips. Powder coated finish. Cabinet interior bottom with a radius flange for increased strength and ease of cleaning. Recessed Toe Space 4 inches high 3-1/2 inches deep, promotes laboratory cleanliness. Cabinet base lower corner reinforcing gusset with 0 to 2-1/2 adjusting levelers on (all four corners). Cabinet height adjustable from 35 to 37-1/2. 7

8 UniLine Base Cabinets Lab cabinets are offered in standard modular sizes that allow you to create a custom laboratory to meet your specific needs. All cabinets feature furniture grade welded steel construction with a durable, chemical resistant, epoxy powder coat finish that meet or exceed SEFA 8, recommended practice for laboratory casework. Other colors available to suit your requirements. (Available in Stainless Steel, Polypro, and Wood) Base Cabinets (standard color: silver beige) Made In The U.S.A. 30 Wall Height Standard 35 ADA 32 Sitting 28 Floor Levelers 1/2 adj, (4) places Service Run 7 Cabinet End View Width 3 Drawer Sitting Height Only 4 Drawer 1 Drawer - 1 Door 1 Door Width Width Width Specify left or right hinged Specify left or right hinged 2 Drawer -2 Door 1 Drawer - 2 Door 5 Drawer - 1 Door 4 Drawer - 1 Door 4 Drawer - 2 Door Width Width Width Width Width VAC 5 Drawer 8 Drawer 6 Drawer 4 Drawer Vacuum Cabinet Width Width Width Width Width FLAMMABLE Base Cabinet Acid Cabinet Flammable Cabinet Sink Unit Cabinet Sink End Unit Width Doors Width Doors Vent Kit Width Vent Kit Width Width Note: Items highlighted in blue are in stock for quick shipping 8

9 Wall Cabinets, Floor Cabinets, and Accessories Wall Cabinets Single Door Wall Cabinet 2 Door Wall Cabinet 2 Door Framed Glass Cabinet 2 Glass Sliding Door Cabinet Width Height Depth Specify left or right hinged Width Height Depth Width Height Depth Width Height Depth Floor Mounted Cabinets (standard color: silver beige) Floor Cabinet Open Front Storage cabinet with 5 adjustable shelves. Height 84, Depth 18 Width Floor Cabinet Solid Hinge Door Storage cabinet with 5 adjustable shelves. Height 84, Depth 18 Width Floor Cabinet Slide Glass Door Storage cabinet has glazed 1/4 glass doors and 5 adjustable shelves. Height 84, Depth 18 Width Casework Accessories (standard color: silver beige) Reagent Shelf Shelves are 4 wide 12 deep and 16 high. For use on island, peninsula, or against wall. Phenolic Resin shelf is 1 thick & 14 deep Length Single Drawer Apron 4 1/2 high. Used to span knee space area and support countertop. Width Depth Wall Shelf 12 deep. Includes vertical fl anges for mounting. Width Knee Space Panel 35 high. Located at the rear of knee space areas. Width 24 to to to End Panel 35 high x 22 or 28 deep. Used to support countertops at the end or middle of a knee space area. Please specify depth Leg Assembly 35 high x 22 or 28 deep. Used to support countertops at the end or middle of a knee space area. Please specify depth Front Rail 2 high x 30, 36 or 48 wide. Used to support counter tops above knee space areas. Please specify width Cabinet Lock Five-Disc tumbler door & drawer cam lock & (2) keys Utility Chase 24 wide x 6 deep x 84 high. Located on an island behind a sink. Used to conceal piping and to serve as mounting for pegboard Rear Filler Panel 35 high x 7 wide. Used to enclose pipe chase behind cabinets on standard 30 deep counters Center Filler Panel 35 high x 4, 10, or 14 wide. Used to enclose the pipe chase at the end of an island. Please specify width Front Filler Panel 35 high x 2, 6, or 12 wide. Used to enclose the space between cabinets to meet casework length requirement. Please specify width End Scribe 35 high x 2, 6, or 12 wide. Used to fi ll the space between the end of casework and a wall. Please specify width

10 Laboratory Countertops, Sinks, and Plumbing Countertops are available in phenolic resin, epoxy resin, and stainless steel, are 24 or 30 inches deep, and can be supplied with or without back splashes. Sink and service cut-outs are fabricated as required. Specify length Phenolic Resin 4 Laboratory Countertops 24 or Phenolic Resin Surfaces are constructed of solid composite panels that have excellent chemical resistance and durability. Surfaces are nonporous and UV, heat, bacteria, and scratch resistant. Available in 1 thickness. Color: Charcoal (sold by the lineal foot) SEFA Compliant, UL1805 Certified. Depth 24 Deep 30 Deep No Backsplash With 4 Backsplash 70118B 70018B Made In The U.S.A. Specify length 4 24 or Epoxy Resin Surfaces & curbs are molded of a modified epoxy resin that is specifically compounded & cured to provide optimum physical & chemical resistance. Surfaces are nonporous, non-conductive, stain & heat resistant. Available in 1 thickness. Color: Black. (sold by the lineal foot) SEFA Compliant, UL1805 Certified. Depth 24 Deep 30 Deep Epoxy Resin No Backsplash With 4 Backsplash 70115B 70015B Specify length 4 24 or Stainless Steel Surfaces are fabricated of type 304,16 gauge steel with #3 satin fi nish. All corners, ends, and joints are continuous Heliarc welded and ground smooth. (type 316 stainless steel available) (sold by the lineal foot) Depth 24 Deep 30 Deep Stainless Steel No Backsplash With 4 Backsplash 70116B 70016B Lab Sink Deep Bowl Pegboards Neutralization Tanks Depth A B H Molded of one-piece, chemical resistant polyolefin, neutralization tanks are designed to dilute and neutralize laboratory waste & concentrated corrosives. Lid 5 Gallon 5 gallon tank (5.5 wide x 14 deep x 20 high with 1-1/2 IPS inlet / outlet) No Note: 5 gallon tank requires (1) bag of limestone. Epoxy, Stainless Steel or Polyolefin Sinks Chemical resistant sinks are molded with integral fl anges allowing dropin mounting. Sinks include 1-1/2 IPS threaded outlet & includes sink stopper & drain outlet. Please specify location in counter top layout of A and B dimensions. Epoxy Resin Sinks A B Depth Polyolefin Sinks A B Depth Stainless Steel Sinks A B Depth W Phenolic Resin Pegboards For drying and storage of lab ware. Pegboard in 3/4 thick and includes a stainless steel drip trough to collect run-off. W H of Pegs Oval Cup Sink Drop-in cup sink available in polyolefin. 1-1/2 IPS tailpiece includes strainer. 3 x x IN Removable Lid 15 Gallon LIMESTONE Cupsinks & Traps Round Cup Sink Drop-in sink available in epoxy or polyolefin. 1-1/2 IPS tailpiece includes strainer. Polyolefin Epoxy Resin OUT 15 gallon tank (17.25 dia. x 15.5 H with 1-1/2 IPS inlet / outlet) No Note: 15 gallon tank requires (3) bags of limestone. Limestone is utilized as the medium for neutralizing the hazardous waste. (50 lb bag) Note: Limestone is not included with tank Polyolefin Jar Trap Trap includes adjustable tailpiece and removable jar. 1-1/2 tailpiece

11 Plumbing, Electrical, and Safety Services The countertop service fixtures are chrome-plated. All fixtures have serrated hose connections except where noted. Color-coated service handles and hole cutouts in countertop are provided. Countertop fixtures are not factory installed. Please specify services required and the fixture location. Countertop Laboratory Plumbing (for Groupings on pages 4-6) Made In The U.S.A. Single Gooseneck 6 swivel gooseneck for use with foot pedal remote. 3/8 NPT. ADA compliant SF DeIonized Water Gooseneck Faucet PVC faucet for distilled water. 6 rigid gooseneck. 3/8 NPT Single Service Gooseneck Faucet Single water, 6 swivel gooseneck. 3/8 NPT with vacuum breaker Deck Mounted Mixing Faucet Hot and cold water faucet. 6 gooseneck. 3/8 NPT with vacuum breaker ADA H/C Mix Gooseneck Faucet 6 swivel gooseneck with wrist handle controls. 3/8 NPT. ADA compliant Foot Pedal Remote Control Valves with heavy chrome plating. ADA compliant. 1/2 NPT. Single Pedal Double Pedal Inline Vacuum Aerator Breaker Aerator for gooseneck 3/8 NPS. Dual check. outlet. Furnished with gasket. 3/8 NPS Aspirator Pump Aspirator pump with 3/8 NPS male inlet Keycock Fixture includes turret and shank connection. Single Outlet Double Outlet Triple Outlet Quad Outlet Single Gang Outlet Brushed cast aluminum box with stainless steel cover. Please specify desired location of pedestal box. Double Gang Outlet Brushed cast aluminum box with stainless steel cover. Please specify desired location of pedestal box. Countertop Pedestal Electrical Services (UL listed) Single Gang Single Face Double Face Duplex/115 V/15a 50131S 50131D Single/230 V/20a 50132S 50132D GFI Duplex/115 V/20a 50135S 50135D Double Gang Single Face Double Face Duplex/115 V/15a 50031S 50031D Single/230 V/20a 50032S 50032D GFI Duplex/115 V/20a 50033S 50033D One Duplex and One 50034S 50034D Single/250 V/20a Electrical & Data Supply Chase Anodized aluminum raceway can be supplied with a variety of electrical or data services. Specify length, type of plug, quantity of plugs, type of data outlet. Cat Laboratory Safety Eye / Face / Body Wash, Safety Showers Swing-Out Eye Wash Deck mounted next to sink. Activates when pivoted. 1/2 NPT. Barrier free Pull-Down Eye Wash Recessed, wall mounted (4 deep), pull-down eye wash safety station. Stainless steel. 1/2 NPT. Barrier free Hand Held Face Body Wash squeeze valve nozzle on 8 coiled hose and bracket. Can be used to rinse body parts while victim is sitting or lying down. Wall or hood mounted, 3/8 NPT, Barrier free. Cat Safety Shower see page

12 SE AireStream Fume Hoods R High efficiency, full duty fume hood in 48, and 96 widths. UniFlow SE AireStream fume hoods are designed for energy savings & maximum user protection. The aerodynamic face opening with airfoil provides uniform air flow through the fume chamber. A constant volume low flow hood with VaraFlow baffle system directs the air through the fume chamber to the bell shaped exhaust outlet with minimal turbulence. UniFlow Superstructure non-metallic construction (NO RUST) for total chemical resistance, superior durability and long life. Interior fume chamber one piece glass smooth, all coved corners for ease of cleaning. Unitized construction reduces weight for ease of installation. 5 year warranty. AireStream Baffle System Features vector flow slots for low flow and high performance. Maintains uniform air fl ow thru the baffl e system to bell shaped exhaust collar outlet. Access Panel removable to access ducting connections, plumbing & electrical services from a single point electrical box,115v/60hz AC operation. Energy effi cient LED vapor proof light fi xture with polished stainless steel refl ectors, and light switch on left column, all factory installed. 28 Vertical Sash Height vertical moving sash for loading & unloading of fume hood. Sash is counterbalanced and connected with coated stainless steel cables, 3/16 tempered safety glass with chemical resistant non-metallic PVC framing track and aerodynamic sash lift. Full 35 Viewing Height for ease of access, unobstructed view of fume chamber, and working with tall apparatus and distillation grids. Ergonomic sash lift contoured for effi cient air fl ow and ease of movement, standard equipment. Angled Picture Frame Opening the aerodynamic face opening with air foil provides uniform air fl ow into the fume chamber and thru the AireStream baffl e system SE AireStream Hood 45621, shown with optional epoxy resin worksurface, acid storage cabinet, & fixtures. See pages for accessories. SASH OPTIONS Air Flow Monitor continuously monitors face velocity air flow, comes standard with analog, digital available. Meets ANSI and OSHA requirements. Optional equipment, (see page 30) Sash Stop located at 1/2 open position to reduce air flow 50%, HORIZONTAL SLIDING MOVING SASHES Sash stops available. Max opening is 50%, (4) panels on (2) tracks, conveniently lift out for equipment set-up or cleaning. 12 OPTIONAL COMBINATION VERTICAL- RISING FRAME with HORIZONTAL-SLIDING SASHES Offers the advantages of both sash types. Horizontal openings offer energy savings while vertical option allows full access to the fume chamber. Frame is of type 304 stainless steel. (see page 13 number 6) Low Resistance Exhaust Collar Engineered to reduce exhaust air flow, static pressure and improve air flow volume & efficiency. 10 Diameter Exhaust Collar Diameter Exhaust Collar For specs on UniFlow SE AireStream Hoods visit

13 R SE AireStream Fume Hoods UNIFLOW SE AIRESTREAM DESCRIPTIONS 1. UniFlow SE AireStream CAV Fume Hood: Air By-pass low fl ow, constant air volume hood. Dual wall unitized construction, all non-metallic corrosion and fire resistant composite fi berglass construction. Varafl ow baffl e system and transition bell exhaust connection. Molded one-piece fume chamber with white glass-smooth surface with all coved corners. Vertical sash to be counter balanced 3/16 tempered safety glass with chemical resistant non-metallic PVC framing track and aerodynamic sash lift. A sash stop is installed at the 1/2 open position. Vapor proof LED light fi xture and control switch are wired to a single point junction box. 115V/60Hz, AC All electrical components are U.L. listed. Optional electrical services see page 25. Fume hood is U.L.1805 classifi ed 2. UniFlow SE AireStream VAV Fume Hood: Same as #1 above except equipped with variable air volume VAV restricted by-pass feature in place of CAV by-pass feature. Ducting must be connected to optional VAV exhaust system controls. Hood Depth B 48 Fume Hood Width A UniFlow SE AireStream Fume Hood with Explosion-Proof Light: Same as #1 above except, equipped with explosion proof incandescent light fi xture. Class I Div II Group A B C & D, Class II Div II Group F & G, 115V/60Hz U.L. listed fixture is installed but not wired. Must be fi eld wired to comply with codes. Optional explosion proof switches, receptacles see page UniFlow SE AireStream Fume Hood: Same as #1 above except equipped to comply to international electrical confi guration. 220V/50Hz AC Optional international electrical confi guration, electrical switches, receptacles see page Horizontal Sliding Sash Option: Add suffix to number above NA 45HS-4 45HS-5 45HS-6 45HS-8 6. Combination Sliding Sash Option: Add suffix to number above NA 45CS-4 45CS-5 45CS-6 45CS-8 Diameter D bell shaped exhaust collar Single Point Junction Box + Fire Extinguisher page 27 (30 /36 ) Questions / Ready to order See page 22 for Plan-A-Hood Width A 1805 U.L.1805 classifi ed (32,38 ) LED Light Fixture Top View Air Flow Monitor UniFlow SE AireStream Hood Dimensions 52 Hood Width A Interior Width C Diameter D (2) Sash Height Width C 35 View Height 59 (24 /30 ) Safety Fume Hood Face Velocity The recommended face velocity for effi ciency & safety is fpm. Lower face velocity may compromise user safety. Sash in full open position should be for setup of apparatus & maintenance service only. If opening is at 1/2 open at 100 fpm (feet per minute), face velocity at full open would be approximately 50 fpm. First Sash 1/2 Open Base Cabinet (see page 8) Sash Management & Design Size Hood Full Open CFM /2 Open CFM /2 Open Static Pressure Front View Optional Services Shown Side View 13

14 SE Laboratory Fume Hoods R Designed for high efficiency, energy savings & maximum user protection. Available in 48, and 96 width; 32 depth X 59 height. The aerodynamic face opening with airfoil provides uniform air flow into the fume chamber. A constant volume low flow hood with VaraFlow baffle system efficiently directs the air flow through the fume chamber to the exhaust outlet with minimum turbulence. UniFlow Superstructure non-metallic construction for total chemical resistance (NO RUST), superior durability and long life. Integral one piece composite liner, glass smooth, all coved corners for ease of cleaning. Unitized construction reduces weight for ease of installation. 5 year warranty. Meets U.L.1805, and NFPA-45 classifi cation with fl ame spread of less than 25 per ASTM E-84. High Efficiency sash management provides for energy savings. User Protection with sash in lowered position, fumes are kept safely away from the user. 29 Sash Height vertical moving sash for loading and unloading of fume hood. Full 36 Viewing Height for ease of access and unobstructed view of fume chamber and working with tall apparatus & distillation grids. Angled Picture Frame Opening aerodynamic face opening with air foil provides uniform air fl ow into the fume chamber, & thru the VaraFlow baffl e system, to the exhaust collar. Energy Efficient fl uorescent vapor proof light fi xture with polished stainless steel refl ectors, and light switch on left column, all factory installed. Air Flow Monitor continuously monitors face velocity air flow, comes standard with analog, digital available. Meets ANSI and OSHA requirements. Optional equipment, (see page 30) UniFlow SE Hood 45511, shown with optional epoxy resin worksurface, base cabinets & fixtures, See pages for accessories. SASH OPTIONS Sash Stop located at 1/2 open position to reduce air flow 50%, Optional equipment VARAFLOW BAFFLE SYSTEM HORIZONTAL SLIDING MOVING SASHES Sash stops available. Max opening is 50%, (4) panels on (2) tracks, conveniently lift out for equipment set-up or cleaning. 14 OPTIONAL COMBINATION VERTICAL- RISING FRAME with HORIZONTAL-SLIDING SASHES Offers the advantages of both sash types. Horizontal openings offer energy savings while vertical option allows full access to the fume chamber. Frame is of type 304 stainless steel. (see page 15 number 6) Sash Full Open Sash Half Open

15 R SE Laboratory Fume Hoods UNIFLOW SE FUME HOOD DESCRIPTIONS 1. UniFlow By Pass Fume Hood with Vapor Proof Light Superstructure to be unitized corrosion and fi re resistant, non-metallic composite fi berglass construction, one piece fume chamber liner to have white glass smooth molded-in fi nish and all coved corners. Varafl ow baffle system and bell shaped exhaust collar. Picture frame sash opening with vertical raising counter balanced clear tempered safety glass sash with chemical resistant PVC framing, track and aerodynamic sash lift. Vapor proof fl uorescent light fi xture and control switch are wired to a single point junction box. 115V/60Hz, AC All electrical components are U.L. listed. Optional electrical services see page 25. Fume hood is U.L.1805 classifi ed. Fume hood is U.L.1805 classified. Specify CAV or VAV. Fume Hood Width A UniFlow By Pass Fume Hood with Vapor Proof Light & Built in Exhaust Blower Same as #1 above except equipped with built-in corrosion resistant, vertical discharge, direct drive exhaust motor/blower, 115 volt, 60Hz, AC with control switches prewired to single point junction box. All electrical components UL compliant. Maximum duct run of UniFlow By Pass Fume Hood with Explosion Proof Light Same as #1 above except equipped with explosion-proof, incandescent light fi xture, Class I Div II Group A B C D Class II Div II Group F& G, 115 volt, 60Hz AC, UL Listed. Installed but not wired, must be wired to comply with local codes. Specify CAV or VAV. 4. UniFlow By Pass Fume Hood with Explosion Proof Light & Built in Exhaust Blower Same as #3 above except equipped with built-in corrosion resistant, non sparking, explosion-proof motor/blower exhaust system, Class I,Group C & D, Class II, Group E F & G, 115, volt 60Hz, AC. Explosion-proof exhaust blower and light are installed but not wired, must be wired to comply with local codes. Maximum duct run of 20. Available in CAV Horizontal Sliding Sash Option - Add suffix to number above 45HS-4 45HS-5 45HS-6 45HS-8 6. Combination Sliding Sash Option - Add suffix to number above 45CS-4 45CS-5 45CS-6 45CS-8 Questions / Ready to order See page 22 for Plan-A-Hood UniFlow SE Hood Dimensions Hood Width A Interior Width C Diameter D (2) 10 Diameter D bell shaped exhaust collar + Top View Fire Extinguisher page Exhaust Blower Fire Extinguisher page 27 Safety Fume Hood Face Velocity The recommended face velocity for effi ciency & safety is fpm. Lower face velocity may compromise user safety. Sash in full open position should be for setup of apparatus & maintenance service only. If opening is at 1/2 open at 100 fpm (feet per minute), face velocity at full open would be approximately 50 fpm. First Width A 32 Sash Management & Design Size Hood Full Open CFM /2 Open CFM /2 Open Static Pressure Sash Height Width C 36 View Height Front View Optional Services Shown Sash 1/2 Open Side View 15

16 High efficiency, full duty fume hood in 36, 48, and 96 widths. UniFlow LE fume hoods are low flow constant volume for energy savings & maximum user protection. The aerodynamic face opening with airfoil provides uniform air flow through the fume chamber. The VaraFlow baffle system directs the air through the fume chamber to the bell shaped exhaust outlet with minimum turbulence. Fume hood is U.L.1805 classified UniFlow LE AireStream Hood 35521, shown with optional epoxy resin worksurface, base cabinet and fixtures See pages for accessories. SASH OPTIONS LE AireStream Fume Hoods R UniFlow Superstructure non-metallic construction (NO RUST) for total chemical resistance, superior durability and long life. Interior fume chamber one piece glass smooth, all coved corners for ease of cleaning. Unitized construction reduces weight for ease of installation. 5 year warranty. AireStream Baffle System Features vector flow slots for low flow and high performance. Maintains uniform air fl ow thru the baffl e system to bell shaped exhaust collar outlet. Access Panel removable to access ducting connections, plumbing & electrical services from a single point electrical box,115v/60hz AC operation. Energy effi cient LED vapor proof light fi xture with polished stainless steel refl ectors, and light switch on left column, all factory installed. 27-1/2 Vertical Sash Height vertical moving sash for loading & unloading of fume hood. Sash is counterbalanced and connected with coated stainless steel cables, 3/16 tempered safety glass with chemical resistant non-metallic PVC framing track and aerodynamic sash lift. Full 32 Viewing Height for ease of access, unobstructed view of fume chamber, and working with tall apparatus and distillation grids. Ergonomic sash lift contoured for effi cient air fl ow and ease of movement, standard equipment. Angled Picture Frame Opening the aerodynamic face opening with air foil provides uniform air fl ow into the fume chamber and thru the AireStream baffl e system. Air Flow Monitor continuously monitors face velocity air flow, comes standard with analog, digital available. Meets ANSI and OSHA requirements. Optional equipment, (see page 30) Sash Stop located at 1/2 open position to reduce air flow 50%, CAV Fume Hood Vs 60 VAV Fume Hood VaraFlow By Pass Design Open 50% Restricted By Pass 50 fpm 474 cfm 100 fpm 474 cfm Sash Full Open Sash 1/2 Open 100 fpm 938 cfm 100 fpm 474 cfm STANDARD HORIZONTAL MOVING SASHES The standard sash for HEMCO fume hoods. Sash stops available. Max opening is 50%, (4) panels on (2) tracks, conveniently lift out for equipment set-up or cleaning. 16 OPTIONAL COMBINATION VERTICAL- RISING FRAME with HORIZONTAL-SLIDING SASHES Horizontal openings offer energy savings while vertical option allows full access to the fume chamber. Frame is of type 304 stainless steel. (see page17 number 6) 474 cfm Sash Closed 200 cfm The CAV with Constant Volume exhaust blower (474 cfm), maintains 100 fpm face velocity at 1/2 open design position. The VAV fume hood would need to be equipped with a variable volume exhaust system to maintain 100 fpm at any sash opening height.

17 LE AireStream Fume Hoods R UNIFLOW LE AIRESTREAM DESCRIPTIONS 1. UniFlow LE AireStream CAV Fume Hood: Air By-pass low fl ow, constant air volume hood. Dual wall unitized construction, all non-metallic corrosion and fi re resistant composite fiberglass construction. Molded one piece fume chamber with white glass-smooth surface with all coved corners. Varafl ow baffl e system and bell shaped exhaust collar. Sash to be counterbalanced, 3/16 tempered safety glass with chemical resistant non-metallic PVC framing, track & aerodynamic sash lift. A sash stop is installed at the 1/2 open position. Vapor proof LED light fixture and control switch are wired to a single point junction box. 115V/60Hz, AC All electrical components are U.L. listed. Optional electrical services see page 25. Fume hood is U.L.1805 classified. Specify CAV or VAV Fume Hood Width A UniFlow LE AireStream VAV Fume Hood: Same as #1 above except equipped with Variable Air Volume VAV restricted by-pass feature, in place of CAV by-pass feature. Ducting must be connected to optional VAV exhaust system & controls. 3. UniFlow LE AireStream Fume Hood with Explosion-Proof Light: Same as #1 above except, equipped with explosion proof vapor tight light fixture. Class I, Div II,Group A B C& D. Class II Div II Group F & G 115V/60Hz, U.L. listed fixture is installed but not wired Must be field wired to comply with codes. Optional electrical services see page UniFlow LE AireStream Fume Hood in CE Configuration: Same as #1 above except equipped to comply with optional CE international electrical configuration V/50Hz AC. Electrical services see page 25, exhaust blowers available. 5. Horizontal Sliding Sash Option: Add suffix to number above. NA 35HS-4 35HS-5 35HS-6 35HS-8 6. Combination Sliding Sash Option: Add suffix to number above NA 35CS-4 35CS-5 35CS-6 35CS-8 Questions / Ready to order See page 22 for Plan-A-Hood Diameter D bell shaped exhaust collar Single Point Junction Box + UniFlow LE AireStream Hood Dimensions Width A Width C LED Light Fixture Fire Extinguisher page Diameter D (2)10 Top View 36, 48, 60,72,96 30 Air Flow Monitor Fume Hood Face Velocity The recommended face velocity for effi ciency & safety is fpm. Lower face velocity may compromise user safety. Sash Management & Design Safety Sash in full open position should be for setup of apparatus & maintenance service only. If opening is at 1/2 open at 100 fpm (feet per minute), face velocity at full open would be approximately 50 fpm. Size Hood /2 Open Full Open /2 Open Static Pressure First 27-1/2 Sash Height Width C 32 View Height /4 Work surface Sash 1/2 Open Base Cabinet (see page 8) Front View Optional Services Shown Side View 17

18 CE AireStream Fume Hoods R Full duty fume hoods in space and energy saving sizes of 30, 36, 48, & 72 widths. UniFlow CE models are low flow constant volume fume hoods that require no VAV controls, no motorized baffles, no costly auxiliary air system and no special integral supply fans. These units can save 50% or more in costly exhaust volume typically required to operate a conventional fume hood. Fume hood is U.L.1805 classified. UniFlow Superstructure non-metallic construction (NO RUST) for total chemical resistance, superior durability and long life. Interior fume chamber one piece glass smooth, all coved corners for ease of cleaning. Unitized construction reduces weight for ease of installation. 5 year warranty. AireStream Baffle System Features vector flow slots for low flow and high performance. Maintains uniform air fl ow thru the baffl e system to bell shaped exhaust collar outlet. Access Panel removable to access ducting connections, plumbing & electrical services from a single point electrical box,115v/60hz AC operation. Energy effi cient vapor proof light fi xture with and light switch on left column, all factory installed. 23 Vertical Sash Height vertical moving sash for loading & unloading of fume hood. Sash is counterbalanced and connected with coated stainless steel cables, 3/16 tempered safety glass with chemical resistant non-metallic PVC framing track and aerodynamic sash lift. Full 27 Viewing Height for ease of access, unobstructed view of fume chamber, and working with tall apparatus and distillation grids. Ergonomic sash lift contoured for effi cient air fl ow and ease of movement, standard equipment UniFlow CE AireStream Hood 14891, shown with optional base cabinet, worksurface and fixtures See pages for accessories. SASH OPTIONS Angled Picture Frame Opening the aerodynamic face opening with air foil provides uniform air fl ow into the fume chamber and thru the AireStream baffl e system. Plumbing Services fi xtures are color coded to specifi c service. (see page 24) Air Flow Monitor continuously monitors face velocity air flow, comes standard with analog, digital available. Meets ANSI and OSHA requirements. Optional equipment, (see page 30) HORIZONTAL SLIDING SASHES The standard sash for HEMCO fume hoods. 48 and 72 hoods only. Max opening is 50%, (4) panels on (2) tracks, conveniently lift out for equipment set-up or cleaning. Sash Stop located at 1/2 open position to reduce air flow 50%,

19 CE AireStream Fume Hoods R UNIFLOW CE AIRESTREAM DESCRIPTIONS 1. UniFlow CE AireStream CAV Hood with Vapor Proof Light: The unitized superstructure features a molded seamless fume chamber with all corners coved. Manufactured of flame retardant chemical resistant composite resin using a minimum of metallic parts. Viewing sash is constructed of 3/16 clear tempered safety glass with frame and track fabricated of chemical resistant PVC. Equipped with Varafl ow baffl e system to efficiently direct air through the fume chamber. Baffl e is easily removed for cleaning. Vapor proof light fixture with column mounted light switch. All electrical services are U.L. & C.S.A listed and factory wired to a single point junction box. Hood is shipped completely assembled. This hood system requires a remotely located exhaust blower. Optional electrical services see page 25. Specify CAV or VAV. 2. UniFlow CE AireStream Hood with Vapor Proof Light and Built-In Exhaust Blower: Same as #1 above except equipped with built-in chemical resistant composite blower with polypropylene impeller wheel and column mounted control switch. Blower motor is 115V/60Hz, A.C. blower and switch are U.L. compliant and factory wired to junction box. Max 10 duct run. 3. UniFlow CE AireStream Hood with Explosion-Proof Light: Same as #1 above except, equipped with explosion proof incandescent light fi xture. Class I, Div II Group A,B,C & D. Class II Div II Group F, & G,115V/60Hz, U.L. listed fi xture is installed but not wired. Must be field wired to comply with codes. Optional explosion proof switches, receptacles see page 25, and exhaust blowers are available. This hood system requires a remotely located explosion proof exhaust blower. 4. UniFlow CE AireStream Hood with Explosion Proof Light & Built-In Exhaust Blower Same as #1 above except equipped with explosion-proof blower 115/230V 60Hz A.C. Class I Groups C & D, Class II Groups E F & G & explosion proof light Class I Div II Groups A B C & D, Class II Div II Groups F & G. Blower and light fi xture installed but not wired. Must be field wired to comply with local codes. U.L. listed switches not included see page 25. Max 10 duct run. 30 Fume Hood Width A Epoxy Resin Worksurface: flat 1 thick, color black Composite Resin Worksurface: dished interior to contain spillage, 1-1/4 thick, color gray Questions / Ready to order See page 22 for Plan-A-Hood Diameter D bell shaped exhaust collar Exhaust Blower UniFlow CE AireStream Hood Dimensions Width A Single Point Junction Box + Fire Extinguisher see page Single Point Junction Box Fire Extinguisher see page 27 Width C Diameter D Top View Top View with Blower Fume Hood Face Velocity The recommended face velocity for effi ciency & safety is fpm. Lower face velocity may compromise user safety. Safety First Width A Sash in full open position should be for setup of apparatus & maintenance service only. If opening is at 1/2 open at 100 fpm (feet per minute), face velocity at full open would be approximately 50 fpm. Sash Management & Design Size Hood Full Open CFM /2 Open CFM /2 Open Static Pressure Sash Height Width C 27 View Height Front View Optional Services Shown / Sash 1/2 Open Side View 19

20 FM SE Floor Mount(Walk-In)Fume Hoods R UniFlow FM SE Floor Mounted (Walk-In) hoods are ideally suited for synthesis, distillation & other rack type operations where tall apparatus is used or equipment is rolled into the work area. In sizes 48, 60, 72, 96, & 120 & depths of 30, 36, and 48. UniFlow Walk-In hoods are available in standard or special sizes to meet various applications. Modular construction can be shipped disassembled for on-site assembly. UniFlow Superstructure to be non-metallic FRP composite construction for total chemical resistance (NO RUST), superior durability and long life. Interior fume chamber to be glass-smooth with Varafl ow baffl e system & bell shaped exhaust collar. Modular construction reduces weight for ease of installation. 5 year warranty. VaraFlow Baffle System maintains uniform air fl ow thru the VaraFlow baffl e system to bell shaped exhaust collar outlet. High Efficiency sash management provides for energy savings. User Protection with sash in lowered position, fumes are kept safely away from the user. 62 Sash Height for viewing of fume chamber, loading and unloading equipment for set up. Full 70 Viewing Height for ease of access and unobstructed view of fume chamber while working with tall apparatus and distillation grids. Double Vertical Sashes to be counter balanced connected with coated stainless steel cables, 3/16 tempered safety glass with chemical resistant non-metallic PVC framing track and aerodynamic sash lift. UniFlow FM SE Hood 11060, shown with optional dished epoxy resin worksurface, & fixtures, See pages for accessories. SASH OPTIONS Angled Picture Frame Opening aerodynamic face opening with air foil provides uniform air fl ow into the fume chamber, & thru the VaraFlow baffl e system, to the exhaust collar. Energy Efficient LED vapor proof light fi xture with polished stainless steel refl ectors, and light switch on left column, all factory installed. Plumbing Services fi xtures are color coded to specifi c service. (see page 24) Electrical Services can be mounted on right or left side. (see page 12) STANDARD VERTICAL MOVING SASHES The standard sash for HEMCO fume hoods, up to 6 foot wide. The sash may be lifted to the completely open position for maximum access thru the fume chamber. Sash stops available. 20 HORIZONTAL SLIDING SASHES The maximum sash opening for the horizontal sash is 1/2 that of the vertical sashes. The smaller opening, means less air exhausted resulting in energy savings. (see page 21 number 4) Air Flow Monitor continuously monitors face velocity air flow, comes standard with analog, digital available. Meets ANSI and OSHA requirements. Optional equipment, (see page 30) Sash Stop located at 1/2 open position to reduce air flow 50%, Optional equipment 51651

21 UNIFLOW SE FLOOR MOUNT DESCRIPTIONS 1. UniFlow SE Floor Mounted CAV Bypass Fume Hood with Vapor-Proof Light: Superstructure to be modular composite chemical resistant FRP non-metal construction. Interior fume chamber to be glass-smooth with Varafl ow baffl e system & bell shaped exhaust collar. Picture frame upper & lower sash opening with counterbalanced sashes of clear tempered safety glass with chemical resistant PVC framing, track, and aerodynamic sash lift. Vapor proof LED light fi xture and control switch are wired to a single point junction box. 115V/60Hz, AC All electrical components are U.L. listed. Optional electrical services see page 25. Fume hood is U.L.1805 classifi ed. Horizontal sliding doors are optional on 96 & 120 hoods, consult factory. Optional VAV. 2. UniFlow SE Fume Hood with Explosion-Proof Light: Same as #1 above except equipped with explosion proof vapor tight light fi xture. Class I Div II Group A B C & D, Class II Div II Group F & G, 115V / 60Hz U.L. listed fixture is installed but not wired. Optional VAV. 3. UniFlow SE Fume Hood: Same as #1 above except equipped to comply to international electrical configuration. 220V/50Hz AC. Optional international electrical configuration, electrical switches, receptacles and exhaust blowers available. Optional VAV. FM SE Floor Mount(Walk-In)Fume Hoods R HOOD Depth B 48 Fume Hood Width A Horizontal Sliding Sashes (4 panels on 2 tracks) - for 96 and 120 hoods only FMHS-8 FMHS-10 Questions / Ready to order See page 22 for Plan-A-Hood Optional Accessories Plumbing Fixtures (see page 24) Fume Hood Fire Extinguisher (see page 27) Electrical Services (see page 25) Air Flow Monitor (see page 30) Diameter D bell shaped exhaust collar + LED Light Fixture Top View Fire Extinguisher see page Depth 36 B 48 SE FM (Walk-In) Hood Dimensions Width A (32,38,50 ) Width A Diameter D (1) 10 (1) 10 (1) 12 (2) 10 (2) 12 Safety Fume Hood Face Velocity The recommended face velocity for effi ciency & safety is fpm. Lower face velocity may compromise user safety. Sash in full open position should be for setup of apparatus & maintenance service only. If opening is at 1/2 open at 100 fpm (feet per minute), face velocity at full open would be approximately 50 fpm. First Sash Height Sash Stop FM SE Floor Mount Fume Hood Sash Management & Design Size hood Full open cfm /2 open cfm View View Height Sash Height Front View Optional Services Shown Side View 21

22 HEMCO Plan-A-Hood Worksheet The Following is a sample of the UniFlow SE Aire-Stream Plan-A-Hood worksheet, Plan-A-Hood worksheets are also available for SE, LE, CE fume hoods. To access go to select the model and click on the Plan-A-Hood Link. UNIFLOW FUME HOOD QTY CAT.NO. AIR BY PASS / CAV CONVENTIONAL / VAV AUXILIARY AIR JCT BOX + CUSTOMER NOTES DISTILLATION RADIOISOTOPE FLUORESCENT LED Light Fixture LIGHT PERCHLORIC ACID ADA AIR FLOW MONITOR QTY CAT.NO. DIGITAL ANALOG OTHER TOP VIEW Fill out this form and to: info@hemcocorp.com FIRE EXTINGUISHER QTY CAT.NO. 20 SQ FT DRY CHEMICAL 30 SQ FT DRY CHEMICAL SASH QTY CAT.NO. VERTICAL MOVING STD HORIZONTAL MOVING COMBINATION H&V SASH STOP QTY CAT.NO. SPECIFY LOCATION PLUMBING SERVICES FIXTURE SERVICES* QTY SERVICE SET OF FOUR Light Switch BLOWER SWITCH QTY CAT. NO. TOGGLE SWITCH 125V,15A TOGGLE SWITCH 125V, 20A TOGGLE SWITCH. 250V, 20A TOGGLE SWITCH W/PILOT MOTOR REMOTE STARTER CONTROLLED SWITCH FIXTURES PLUMBING SERVICES* QTY CAT. NO. SERVICE SET OF FOUR *SPECIFY AIR,GAS,VAC,C/W OR OTHER *SPECIFY AIR,GAS,VAC,C/W OR OTHER ELECTRICAL SERVICES QTY CAT. NO. DUPLEX RECEPT. 125V,15A DUPLEX RECEPT. 125V, 20A SIMPLEX RECEPT. 250 V DUPLEX GFI 125V, 15A DUPLEX GFI 125V, 20A ACCESS PANEL QTY CAT. NO INSIDE LOCATION OUTSIDE LOCATION FRONT VIEW WITH BASE CABINET Optional services shown (see 24 for service options) SERVICE Service SLOT Slot ELECTRICAL SERVICES QTY CAT. NO. DUPLEX RECEPT. 125V,15A DUPLEX RECEPT. 125V, 20A SIMPLEX RECEPT. 250 V DUPLEX GFI 125V, 15A DUPLEX GFI 125V, 20A ACCESS PANEL QTY INSIDE LOCATION OUTSIDE LOCATION CABINETS QTY CAT. NO. SINK CABINET BASE CABINET ACID CABINET FLAMMABLE CABINET PLAN VIEW OF WORK SURFACE (see page 23 for worksurfaces) Questions / Ready to order Call HEMCO: WORKSURFACE QTY CAT. NO. EPOXY RESIN PHENOLIC RESIN 316 STAINLESS STEEL This is page 1 of 2, to see all Plan-A-Hood work sheets go to select the model & click on Plan-A-Hood Standard Color is Silver Beige, other colors are available. 22 Pearl White - 01 Silver Beige - 02 Pewter Gray - 03 Zircon Blue - 04

23 Fume Hood Worksurfaces and Base Cabinets A complete line of worksurfaces and cabinets to suit any application from economical light duty to heavy acid and solvent use. Select the worksurfaces and cabinets that meet your laboratory s requirements. Standard sizes are listed below. HEMCO s technical staff can make recommendations to suit your specific needs. (UniFlow SE, LE hoods only) Epoxy Resin, color: black, 1-1/4 thick, 3/8 dished Epoxy Resin Worksurfaces are recommended for general laboratory work where greater chemical resistance is required. Surface is dished 3/8 to contain spillage. Worksurface is cast of thermosetting epoxy resin, creating a molded solid 1-1/4 thick top which is extremely hard, abrasion and heat resistant. Size Size 36 W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D (UniFlow SE, LE hoods only) Stainless Steel, satin finish, 1-1/4 edge, 3/8 dished Stainless Steel Fume Hood Worksurfaces are fabricated of type 304,16 gauge steel with #3 satin fi nish. Surface is dished 3/8 to contain spillage. All corners, ends, and joints are continuous 1-1/4 heliarc welded and ground smooth. Type 316 stainless steel is available. Size Size 36 W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D (UniFlow SE, LE) Phenolic Resin, color: black, 1-1/4 thick, dished 1/4 Phenolic Resin Worksurface are recommended for general laboratory work where high concentrations of solvent, acids and alkalies are being worked with. Work surface combines excellent chemical resistance scratch and wear resistance. Surface is flat 1-1/4 thick, dished 1/4. Size Size 36 W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D W x 30 D W x 36 D Fume Hood Base Cabinets & Tables Base Cabinet Constructed of furniture grade steel. With adjustable shelf and levelers. Width Doors Acid Cabinet Interior is lined with one piece acid resistant white composite resin liner and all coved corners, for superior corrosion resistance, with vents and fi xed shelf. Width Doors Vent Kit Flammable Cabinet provides safe storage Sink Unit Cabinet Constructed of of fl ammables. furniture grade steel. Constructed of welded Cabinet has hinged double wall furniture grade steel. Cabinet doors and levelers. has an adjustable shelf and locking hinged doors. Meets NFPA codes. Width Width Vent Kit Fume Hood Base Table Heavy duty, all welded 2 square tube steel construction. Standard depth is 29. Each leg has levelers with fi tted black boots. Available in, standard 35 bench height, & 28 sitting height. color: silver beige Width Std Sitting For the full offering of Lab Furniture consult the Lab Planning Solutions Catalog or visit 23

24 Fume Hood Wall Mounted Plumbing Fixtures Fume hood remote control service fixtures feature epoxy coated brass, chemical resistant, color-coded, serrated hose connections, and 3/8 NPT brass valves with rod and handle assembly. Plumbing fixtures are factory installed on hood, they can be pre-plumbed if specified. Please specify service required, fixture location, and inside or outside service access panels. Conforms to ANSI Z Service Fixture Color Code Chart Green - Cold Water Red - Hot Water Blue - Gas Orange - Air Yellow - Vacuum Brown - Nitrogen Black - Steam White - Deionized Water Service Set of Two (specify left or right mounting) Two remote controlled service fixture set. Color-coded index buttons with matching color-coded serrated tip. Specify service required. Epoxy coated brass FS Service Set of Four (specify left or right mounting) Four remote controlled service fixture set. Color-coded index buttons with matching color-coded serrated tip. Specify service required. Epoxy coated brass FS Service Set of Six (specify left or right mounting) Six remote controlled service fixture set. Color-coded index buttons with matching color-coded serrated tip. Specify service required. Epoxy coated brass FS DI Faucet Pure water 6 rigid PVC goose neck DI Faucet Pure water 6 swivel tin-lined gooseneck. Epoxy coated brass Gooseneck PVC Service Fixture Wall mount, no valve, constructed of PVC Service Fixture Cold water, remote controlled epoxy coated brass turret Water Faucet with Vacuum Breaker Cold water 6 swivel gooseneck. Epoxy coated brass Water Faucet with Vacuum Breaker Cold water remote controlled 6 swivel gooseneck. Turret & gooseneck are epoxy coated brass CW Water Faucet Cold water remote controlled 6 swivel gooseneck. Turret and gooseneck are epoxy coated brass CW Service Fixture Remote controlled single service outlet. color-coded index buttons with matching color coded serrated tip outlets Base Fixture Deck or wall mount, 3/8 NPT remote, no valve. PVC Lab Turret Deck or wall mount, 3/8 NPT, no valve, PVC Mix Faucet Hot and cold remote controlled 6 swivel gooseneck. Turret and gooseneck are epoxy coated brass Mix Faucet Hot and cold water remote controlled turret. Turret is of epoxy coated brass High Flow Water Valve, Straight Pattern Ball valve construction with quarter turn open / close, used for supply and return connections. Cat Single Keycock Single fl ange mounted needle valve, keycock with integral fl ange and shank connection. Epoxy coated brass. 3/8 NPT with lock nut. Single Double Aspirator 3/8 NPS male inlet Epoxy coated brass External Mounted Vacuum Breaker Breaker with 3/8 IPS inlet and outlet. Chrome plated brass

25 Fume Hood Electrical Services Electrical services are UL, CSA & CE approved. They come factory installed, wired to a single point junction box when ordered with fume hoods. Services must be wired to comply with local codes. HEMCO welcomes the opportunity to quote your special application. Electrical Services Duplex Receptacle 115V single phase receptacle. Installed on front column of fume hood. Includes junction box and cover plate. UL listed. amps 15 amps amps Single Receptacle 230V single phase receptacle. Installed on front column of fume hood. Includes junction box and cover plate. UL listed. amps 15 amps amps GFI Duplex 115V consists of combination ground fault interrupters, 3-wire polarized grounded. Includes junction box & cover plate. amps 15 amps amps Single Receptacle with On/Off Switch Receptacle has on-off switch to control power to plug-in. 115V/15 amps. Includes junction box & cover plate. UL listed Light Switch 115V/15 amps. Includes junction box and cover plate. UL listed Explosion-Proof Switch For use in hazardous locations. Surface mount type with cast iron housing. Specify 115V/20 amp or 230V/20 amp. UL listed Explosion-Proof Junction Box For use in hazardous locations. For use on explosion-proof motors and blowers. Has hole for selftapping ground screw. Not installed at factory. U.L. listed Continental European Socket with cover cap Blower Switch with Pilot Light Includes junction box and cover plate. UL listed. volts/amps 115V 15 amps V 20 amps LED Light Fixture Energy Effi cient, Long Life, LEED Compatible, 4 foot electrical cord, Available in (3) sizes, For SE or LE models. Type: CEE7 color: gray Rating 250V/16 amp, installed at factory Explosion-Proof Light Std Explosion-Proof Receptacle For use in hazardous locations. Surface mount type with aluminum housing, 3-pole, 2-wire, Specify 115V/20 amp or 230V/20 amp. Not installed at factory. UL listed Indian / South Africa Socket ISA Motor Starter Switch Mounted in a single gang receptacle box with face plate. Factory mounted not wired. Includes thermal overload protection. Double pole switch for up to 1 HP, single phase, 60 Hz 115V 50 Hz, 230V AC motors. UL listed LED Light Fixtures Explosion-Proof Services For use in hazardous locations. Gray, two-coat epoxy fi nish with easily removed prismatic globe. Factory mounted, not wired. Accepts bulb up to 150 watts (bulb not included). 115 / 230V UL listed. Class I Div II Group A, B,C,D Class II Div II Group F& G Type: BS546 color: white Rating 250V/15 amp, installed at factory LED Hood size 36 (1) & 48 (1) 36 LED Hood size 60 (1) and 96 (2) Explosion-Proof Ground Fault Interrupter For use in hazardous locations. Factory sealed GFI is designed to interrupt a circuit when a ground fault us detected. 115V 60 Hz, 20 amp. Not installed at factory. UL listed International Electrical Services ( Configuration ) United Kingdom / Ireland Shuttered Socket Type: BS1363 color: white Rating 250V/13 amp installed at factory Service Port Pass-Through Convenient port allows cords, tubes, or cables to pass to and from the hood LED Hood size 72 (1) Explosion-Proof Fixture For use in hazardous locations. Gray, two coat epoxy finish with easily removed prismatic globe. Accepts long neck incandescent bulb up to 300 watts, (bulb not included)115 / 230V. Factory mounted, not wired. UL listed. Class I Div I Group C, D, Class II Div I Group E, F & G Explosion-Proof Plug Adaptable for use with all receptacles. 3-pole, 2-wire, Specify 115V/20 amp or 230V/20 amp AC. Not installed at factory. UL listed Continental European Panel Mount Socket Type: CEE7 color: white Rating 250V/15 amp installed at factory

26 Fume Hood Sink and Plumbing Services A complete line of sinks in epoxy resin, polypropylene, and stainless steel. We also offer a wide variety of plumbing accessories including neutralization tanks and steam baths. HEMCO welcomes the opportunity to quote your special applications. Additional sink sizes are available. Contact factory for more details. Conforms to ANSI Z Fume Hood Laboratory Sinks Epoxy Resin Sink Laboratory sink made of chemical and corrosion resistant epoxy resin. Drop-in sink. color: black. Please specify desired location. Includes sink stopper & drain outlet. 26 Size 1 9 x 6 x 6 deep x 12 x 8 deep x 15 x 11 deep x 16 x 8 deep Polypropylene Sink Laboratory sink made of chemical resistant heavy duty polypropylene. Drop-in sink. color: black. Please specify desired location. Includes drain outlet. Size 1 12 x 8 x 8 deep x 10 x 6 deep x 15 x 12 deep x 20 x 9 deep Fume Hood Cup Sinks, & Plumbing Fixtures Cupsink 6 Diameter polyolefin cupsink with 1-1/2 IPS tailpiece and outlet strainer Jar P Trap P- trap includes adjustable tailpiece and removable jar. 1-1/2 IPS tail piece Oval Cup Sink Drop-in cup sink available in polyolefin. 1 1/2 IPS tailpiece includes strainer. 3 x x Liter 8.5 h X 15.9 w X 12.3 deep 20 Liter 8.5 h X 15.9 w X deep Oval Wall Cupsink 6 x 3 Cupsink is made of polyolefin with 1-1/2 IPS tailpiece and outlet strainer P Trap P-trap is made of polypropylene with 1-1/2 IPS tailpiece IN Bead Baths Stainless Steel Sink Laboratory sink made of one-piece, type 304 stainless steel and polished to a 4 satin finish. Drop-in sink. Underside is sound deadened to reduce drumming. Specify location. Includes drain outlet. Removable Lid 15 Gallon Size 1 12 x 12 x 7.5 deep x 16 x 7.5 deep x 22 x 7.5 deep x 28 x 7.5 deep Neutralization Tanks Molded of one-piece, chemical resistant polyolefin, neutralization tanks are designed to dilute and neutralize laboratory waste and concentrated corrosives. Lid 5 Gallon LIMESTONE OUT 5 gallon tank (5.5 wide x 14 deep x 20 high with 1-1/2 IPS inlet / outlet) No Note: 5 gallon tank requires (1) bag of limestone. 15 gallon tank (17.25 dia. x 15.5 H with 1-1/2 IPS inlet / outlet) No Note: 15 gallon tank requires (3) bags of limestone. Limestone is utilized as the medium for neutralizing the hazardous waste. (50 lb bag) Note: Limestone is not included with tank Laboratory bead baths allow you to quickly change the temperature of the bath, without the long wait times associated with water baths. Temperatures are consistent and uniform through out the bath, with a thermal uniformity of +/- 1.0 at 37 degrees Celsius. Bead baths do not use water, so you do not have to turn them off, and there is nothing to evaporate. Available in either V-6.0A 50/60 Hz or V-3.0A 50/60 Hz Includes power adapter, stainless steel lid, and instructions Temperature range Celsius ambient + 5 degrees to 80 degrees No racks needed to hold equipment in the water bath, beads naturally hold items.

27 Apparatus Grids and Fire Extinguishers Distillation apparatus grids designed to mount small apparatus and glassware in the interior of the fume hood, maximizing the work area. Grids are available in aluminum, stainless steel, or fiberglass to meet specific needs. Mounting options: 1. Grids can be mounted to the side walls of the fume hood, 2. When more strength is required, grids can mount to both the sidewalls and the worksurface, consult factory for details. Fume Hood Apparatus Grids Left Wall Width between walls Right Wall 35 High Aluminum Apparatus Grid and Catalog Number Fume Hood Width Grid Width for Hood as Installed Aluminum Rod Assembly 1/2 dia All components are machined from solid aluminum bar stock. All aluminum lattice rod components are furnished with a satin (brushed) fi nish. Backing plates for hood wall and mounting screws for fl anges are not included. Fume hood with apparatus grid installed Stainless Steel Apparatus Grid and Catalog Number Fume Hood Width Grid Width for Hood as Installed Stainless Steel Assembly 1/2 dia Stainless steel components offer superior strength and corrosion resistance for even the most demanding applications. All components are machined from Type 316 stainless steel bar stock and polished to a satin fi nish. Backing plates for hood wall and mounting screws for fl anges are not included. Non-Metallic Composite Apparatus Grid and Catalog Number Fume Hood Width Grid Width for Hood as Installed Fiberglass Rod Assembly 1/2 dia All rod components are white fi berglass. All connectors are molded in black nylon for strength and chemical resistance. Backing plates for hood wall and mounting screws for fl anges are not included. Half open style clamps, facilitate adding or removing rods from existing assembly. Fume Hood Fire Extinguishers Foremost: fume hood fires must be extinguished promptly, failure to do so could result in loss of life and valuable equipment & processes. In case of a fire inside of a fume hood, 1. Lower the sash into the closed position. 2. Pull the manual front mount discharge cable to activate the fire extinguisher. 3. Shut off the fume hood blower on the fume hood, and any remote exhaust blowers that are connected. 4. Shut off any utility services that could feed a fire. Fire extinguisher activation occurs at 200 Fahrenheit. These are recommendations, contact your laboratory safety officer for guidelines. 1. Fire Extinguisher with automatic activation at 200 Fahrenheit. With dry chemical for class ABC fi res, 20 Square feet...cat With Halon, 20 Cubic feet...cat Fire Extinguisher with automatic activation at 200 Fahrenheit. With dry chemical for class ABC fi res, 30 Square feet...cat With Halon, 30 Cubic feet...cat Note: Larger hoods may require (2) extinguishers, based on interior cubic dimensions. 27

28 Laboratory Ventilation Recommendations Proper placement and use of fume hoods and blowers are important laboratory ventilation requirements. HEMCO offers the following suggestions to help in your laboratory layout. For technical support please contact HEMCO. Location of Hood Room air supply, air flow patterns and user convenience e are the most important considerations in planning the location of hoods within the laboratory. Hoods placed directly in front of doors, open windows, or air conditioning registers will not perform efficiently. Drafts create turbulence at the face of the fume hood and disrupts air flow. Hoods should not be placed where users would be forced to work in the line of traffic. Traffic in front of the hood adversely affects fume hood air flow When common exhaust or supply systems are used for several hoods, the hood units should be arranged so minimum amount of ductwork is required. See page 30 for more suggestions on planning your ducting system. Hoods used as general lab exhaust should generally be located on the opposite wall from the side-wall inlet registers or doors. The hoods should be located so that air from the registers or diffusers sweep through the laboratory area first then into the hoods. 28 Hood Operation Consult Lab Safety Officer for correct use of fume hood. Blower page 32 Supply Air Diffusers See below Hoods should not be used as laboratory storage space. Unnecessary necessary material or unused bottles and flasks can block exhaust openings and interfere with hood performance. OSHA requires an fume hood be equipped with an Air flow Monitor to track air flow velocities and warn operator of potentially dangerous low air flows due to damper, blower failure, blockage of ductwork system, or extreme sash opening height. 24 or 48 Fume Hoods Carbon / HEPA Inline Filter Module See below Fume Hood Radial Flow Supply Air Diffuser The Radial Flow Diffuser is designed to provide high volume / low 24 velocity airfl ow into laboratory space specifi cally where fume hoods are located. The uniform / low velocity airfl ow prevents turbulence at the hood face and effi ciently distributes supply air to ensure correct air change that supports fume hood air volume requirements. Available duct sizes: 8 or 10 inches for 24 x 24 inch models, and 10 or 12 inches for 48 x 24 inch models. Can be used for class 1,000 to class 100,000 rooms. 24 X cfm X ,000 cfm Clean Aire In-Line Carbon and or HEPA Filtration Systems HEPA filter paks effectively collect particulate contaminants from the exhaust air stream. Clean Aire Carbon Filter Pak CFM Size Duct Size x 15 x 35 1/2 4, 8 diameter x 26 x 35 1/2 8, 10, 12 diameter Carbon Filters Prefilter (6 per carton) CFM Size No CFM Size x 12 x x 12 x x 24 x x 24 x Clean Aire HEPA Filter Pak CFM Size Duct Size x 15 x 35 1/2 4, 8 diameter x 26 x 35 1/2 8, 10, 12 diameter Carbon Filters Prefilter (6 per carton) CFM Size No CFM Size x 12 x x 12 x x 24 x x 24 x

29 Energy Savings Recommendations A comparison of two fume hoods below is based on a designed 12 high operating sash height with sash management and a full open sash height without sash management. By maintaining a lower operating height, energy can be conserved, material costs saved, and user safety enhanced. Sash Management can SAVE 57% on fume hood operating cost. Energy Savings Annual cost to operate $ UniFlow 72 CAV bypass fume hood WITHOUT sash management requires 1170 cfm to maintain 100 fpm (face velocity) with the sash fully open. At an average of $7.00 per cfm, the annual cost to operate this fume hood would be $ Annual cost to operate $ UniFlow 72 CAV bypass fume hood WITH sash management only requires 500 cfm to maintain 100 fpm (face velocity) with operating height at 14. At an average of $7.00 per cfm, the annual cost to operate this fume hood would be $ Total Energy SAVINGS = $ per year Equipment Savings Based on 20 of ducting, (1) 90 elbow, stack outlet, and exhaust blower CAV WITHOUT Sash Management UniFlow 72 CAV bypass fume hood WITHOUT sash management would require 12 diameter ducting to handle the volume and duct velocity at $ per foot. UniFlow 72 CAV bypass fume hood WITHOUT sash management an exhaust blower designed to maintain 100 fpm (face velocity) would require w.g. (static pressure) with a 10 diameter inlet and 1/2 hp motor at $ UniFlow 72 CAV bypass fume hood WITH sash management would only require 8 diameter ducting to handle the volume and duct velocity at $ per foot. UniFlow 72 CAV bypass fume hood WITH sash management an exhaust blower designed to maintain 100 fpm (face velocity) with sash at 14 operating height, would only require w.g.(static pressure) with a 9 diameter inlet and 1/4 hp motor at $ Sash Stop CAV WITH Sash Management Total Equipment SAVINGS ducting & blower = $ Importance of Duct Velocity Duct Velocity is important to the safe ventilation of laboratory fumes & particulate,1200 to 1500 fpm (duct velocity) is recommended. A 72 fume hood with 1170 cfm (for full sash opening) will have a 12 diameter belled outlet duct connection & will maintain 1400 fpm duct velocity. A 72 fume hood with 500 cfm (for 12 sash opening) will have an 8 diameter belled outlet duct connection & will maintain 1400 fpm duct velocity for over a 50% reduction in volume. Importance of Room Air Changes per Hour Air Changes per Hour is typical to a laboratory and in some cases the fume hood not only exhausts hazardous fumes but serves as the general ventilation of the lab. The lab should always be under negative pressure; thus 10% of the exhaust should come in from the corridor under or around the door. For example, a 12 x 25 x 9 high room, at 2700 cu ft, would require approximately 450 cfm. With the hood at 500 cfm and 10% of that coming from the corridor, the minimum supply in the room would be 450 cfm. However if a greater amount is brought in, there would need to be Sash Stop located at 1/2 general exhaust from the room to prevent open to reduce the room from being pressurized. air flow 50%, Make-Up Air, Considering that a fume hood exhausts a large amount of air from the lab space, it is necessary to ensure that there is sufficient air supply to the lab, yet still maintaining a negative air pressure to the surrounding area. Because of the additional resistance in the duct system, the static pressure of inline filtration would need to be calculated when sizing the exhaust fan Filtration, Depending on the contaminant, an inline HEPA or carbon filter may be necessary to prevent pollution to the outside environment. (see page 33 for filtration options)

30 Ventilation and Duct Design Ductwork connected to fume hoods may be arranged in a variety of patterns depending on requirements. Generally, the best exhaust system involves the shortest duct length and the fewest elbows. Duct size, length, and number of elbows affect static pressure loss and blower effi ciency. Ideally, each fume hood should have its own ducting and blower to maximize hood fl exibility and reduce danger of backdraft from other hoods. Common or manifold ductwork designs can be used, provided duct and blower have been sized properly. In these designs, individual hood dampers are recommended to balance the system. Hood users must be aware of how different hood exhaust fumes will react when mixed in the ductwork. Rigid PVC ductwork is recognized as an excellent fume hood exhaust duct material. The smooth interior surface reduces static pressure loss and chemical waste build up, and PVC is extremely resistant to a wide variety of reagents. For some applications fl exible PVC lined duct provides adequate service and can signifi cantly reduce installation costs. When planning exhaust ducting, duct size, length, number of bends, and exhaust material must be considered. Consult HEMCO for Lab Ventilation Solutions Weather Cap #12-Page 31 Exhaust Blower See page 32 Roof Rain Skirt #10-Page o Elbow #4-Page 31 Coupling #3-Page 31 Reducer #15-Page o WYE #6-Page o Elbow #4-Page 31 Butterfl y Damper #8-Page o Elbow #5-Page 31 Blast Gate Damper #9-Page 31 InLine HEPA / Carbon Filter Pak Filter paks are used in laboratory exhaust and supply systems to remove hazardous fumes & particulate from the airstream. Filters are loaded with virgin coconut activated carbon to efficiently absorb organic solvents and acid fumes. The filter pak housing features a hinged access door with gaskets and spring latches for convenient filter changes. Inlet and outlet plenums with duct connection collars are installed. The carbon filter pak can also be paired with a HEPA filter pak to collect particulate contaminants. (see page 33) Air flow Monitor Note: OSHA recommends Air flow Monitors to be installed on all fume hoods. Air Flow Monitor Floor Continuously monitors face velocity air fl ow of fume hood. Select and calibrate at desired fpm velocity set point. If the hood face velocity falls below set point, an audible alarm sounds and a visual red indicator light appears. Air fl ow alarm is factory installed or can be field installed. 115V/60Hz AC Air Flow Monitor with Digital Display Continuously monitors face velocity air fl ow of fume hood. A digital display of face velocity in m/sec or fpm that indicates safety reading with an audible alarm. Push button calibration and 3 programmable input/ output relays. Factory installed or can be fi eld installed

31 Fume Hood Ductwork & Venting Accessories Ducting and accessories are chemical resistant and easy to install. Flexible and Rigid PVC Ducting Flexible Ducting neoprene impregnated fiberglass reinforced with steel helix wire. Standard 12 lengths. Each piece includes 2 clamps PVC Rigid Ducting chemical resistant for permanent installations. Standard 10 lengths with straight ends PVC Coupling required to connect straight sections PVC 90 o Elbow used in order to offset obstacles. Has belled ends for duct connections PVC 45 o Elbow used in order to offset obstacles. Less static pressure loss than a 90 o elbow. Has belled ends for duct connections PVC 45 o WYE lateral for joining common ductwork in multiple hood designs. Branch diameter may be sized to 2 to 4 smaller than main diameter. Has belled ends for duct connections PVC Tee used in manifold exhaust systems. Has belled ends for duct connections PVC Butterfly Damper modifi es cfm for single or multiple hood arrangement. Has belled ends for duct connections PVC Blast Gate Damper a gate that slides in and out to control cfm. Has belled ends for duct connections PVC Rain Skirt slips over straight pipe on roof to slope water away from cutout PVC Vent Outlet for horizontal venting through wall or window. Angled end prevents rain from entering. Male connector included Zero Pressure Weather Cap discharges fumes vertically away from roof. Self-draining. Minimal static pressure loss. This is the recommended weather cap A B 13. Round to Round Transition to smaller duct diameter

32 Fume Hood Exhaust Blowers Ordering Info A complete line of belt and direct drive exhaust blowers that are chemical resistant & available in standard and explosion-proof models. HEMCO blowers are designed to operate effectively and efficiently to remove noxious & hazardous fumes. Standard 115V 60Hz & international electrical configuration of 220V 50Hz AC available. Epoxy Coated Steel Blower Belt Drive Standard (STD) belt drive steel blower and impeller wheel are epoxy coated for superior chemical resistance. Explosion-proof blowers (EXP) have epoxy coated, non-sparking aluminum impeller wheel. V-belt drive and adjustable pulleys permit fi eld balancing. Seven discharge positions to suit installation. Weather housing is furnished. Motor has thermal overload protection. Specify: 115V single phase, 230V single phase, 230/460V three phase or 208V(consult factory). 1 year manufacturer s warranty Catalog Number and Static Pressure cfm A Inlet Diameter B Outlet Size 1/2 Static Pressure 3/4 Static Pressure 1 Static Pressure 1 1/2 Static Pressure HP STD EXP HP STD EXP HP STD EXP HP STD EXP /8 10 1/8 x 4 1/8 1/ / / / /8 10 1/8 x 4 1/8 1/ / / / /8 10 1/8 x 6 3/8 1/ / / / /8 10 1/8 x 6 3/8 1/ / / / Dia. A B B /8 11 1/2 x 8 1/4 1/ / /8 11 1/2 x 8 1/4 1/ / / /8 11 1/2 x 8 1/4 1/ / / /8 11 1/2 x 8 1/4 1/ / / / /8 13 3/8 x 8 1/4 1/ / /8 13 3/8 x 8 1/4 1/ / / /8 13 3/8 x 8 1/4 1/ / / Epoxy Coated Steel Blower Direct Drive Direct drive steel blower and impeller wheel are epoxy coated for superior chemical resistance. Explosion proof blowers have epoxy coated non-sparking aluminum impeller wheels. Motor is 115V, 1 phase and has thermal overload protection. 1 year manufacturer s warranty A Inlet Diameter B Outlet Size HP STD EXP 1/4 SP 1/2 SP 3/4 SP 1 SP cfm cfm cfm cfm Dia. A B B 6 7 X 4-3/8 1/ /4 X 5-7/16 1/ /8 X 4-1/8 1/ /8 X 5-1/8 3/ Standard motors are 115V, 60Hz / 1 phase. Explosion proof motors are 115/230V, 60Hz, 1 phase. Other voltage, hertz, and phase motors are available. Polypropylene Belt Drive Blowers High effi ciency impellers produce low power consumption, reduced operating costs and quiet operation. 20 forward curved blades, in fi re retardant polypropylene. Non-static and oil resistant V-belt, cast iron pulleys, adjustable pulleys available, adjustment for tensioning and belt replacement. 230V explosion proof, non sparking, chemical resistant for hostile or hazardous environments. 115V single phase or three phase. Non-static and oil resistant V-belt, cast iron pulleys, adjustable pulleys available, adjustment for tensioning and belt replacement. 1 year manufacturer s warranty Catalog Number and Static Pressure B cfm A Inlet Diameter B Outlet Diameter 0.5 Static Pressure HP 0.75 Static Pressure HP 1.0 Static Pressure HP HP STD EXP HP STD EXP HP STD EXP / / / A / / / / / / / / /

33 Clean Aire In-Line Filtration Systems HEMCO HEPA filter paks effectively collect particulate contaminants from the exhaust air stream. HEPA filters are % effective at removing particulate.3 micron and larger. The filter pak housing features a hinged access door with gaskets and spring latches for convenient filter change. Inlet and outlet plenums with duct connection collars are installed. The HEPA filter pak can also be paired with a carbon filter pak to remove chemical fumes and odors. Clean Aire In-Line HEPA Filtration Systems Note: HEMCO recommends a minihelic or magnehelic gauge to monitor the airfl ow differential across the fi lter. The static pressure indicated would alert when to change fi lter. The gauges can be hood or fi lter mounted. We recommend ordering a back-up replacement fi lter. Clean Aire HEPA Filter Pak CFM Size Duct Size x 15 x 35 1/2 4, 6,8 diameter x 26 x 35 1/2 8, 10, 12 diameter HEPA Filters Prefilter (6 per carton) CFM Size No CFM Size x 12 x x 12 x x 24 x x 24 x Clean Aire In-Line Carbon Filtration Systems HEMCO carbon filter paks are used in laboratory exhaust and supply systems to remove chemical odors and vapors from the airstream. Filters are loaded with virgin coconut activated carbon to efficiently absorb organic solvents and acid fumes. The filter pak housing features a hinged access door with gaskets and spring latches for convenient filter changes. Inlet and outlet plenums with duct connection collars are installed. The carbon filter pak can also be paired with a HEPA filter pak to collect particulate contaminants. Note: A standard 01 activated carbon filter for organics is included. HEMCO recommends the sampling kit to check if there has been a breakthrough in the carbon fi lter, and ordering a back-up replacement fi lter. Clean Aire Carbon Filter Pak CFM Size Duct Size x 15 x 35 1/2 4, 8 diameter x 26 x 35 1/2 8, 10, 12 diameter Carbon Filters Prefilter (6 per carton) CFM Size No CFM Size x 12 x x 12 x x 24 x x 24 x HEPA / Carbon Bag In - Bag Out Systems Filter housing is fabricated of type-304 stainless steel and requires (1) carbon filter absorber, (1) 24 X 24 X 2 30% pleated prefilter and (1) bag. Bag-In bag-out fi lters are designed to meet air fi ltration requirements to handle hazardous fumes and vapors. The housing incorporates a ribbed bagging ring around the side access door over which a specially designed plastic bag is attached. Old fi lter is removed then new fi lters are then installed and changed through the bag to reduce the risk of exposure to personnel. Note: The fi lter is not included with the housing. We also, recommend a sampling kit to check if there has been a break through in the carbon fi lter, and ordering a back-up replacement fi lter. Clean Aire HEPA Filter Bag-In Bag-Out System Description CFM Size Clean-Aire HEPA Filter Bag-In Bag-out System X 26 X 35-1/ HEPA Filters X 24 X HEPA Prefi lter ( 6 per carton) X 24 X Replacement Bags (2 per carton) Clean Aire Carbon Filter Bag-In Bag-Out System Description CFM Size Clean-Aire Carbon Filter Bag-In Bag-out System X 26 X 35-1/ Carbon Filters X 24 X Carbon Prefi lter ( 6 per carton) X 24 X Replacement Bags (2 per carton)

34 Canopy Hoods Made In The U.S.A. Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Standard color: silver beige Wall Canopy Hoods (fiberglass or stainless steel, Includes wall mounting kit) 30 B Width A Side Wall Panels Fiberglass Stainless Steel Cat Diameter D (2) A Top View Outlet Diameter For blowers (see page 32) For base cabinets (see page 23) 44.5 For blowers (see page 32) For base cabinets (see page 23) Width A Depth B Side Wall Panels Fiberglass Stainless Steel Cat Diameter D (2) left side 25.5 A Top View Outlet Diameter Outlet Diameter Top View Optional Side Wall Panel (1) specify left or right Corner Canopy (includes mounting kit, to install canopy to two adjacent walls) Side Wall Panel (fiberglass or stainless steel) kit includes one wall panel and hardware Rear Wall Panel (consult factory for details) Vapor Proof Light & Switch Blower Switch (blower not included) Island Canopy Hoods (fiberglass or stainless steel) Suspended Island Canopy Hood Mounting Kit Includes all components to secure to ceiling including 4 long threaded rods Side Wall Panel 18 (fiberglass or stainless steel) kit includes one wall panel and hardware Corner Canopy Hoods (fiberglass, Includes wall mounting kit) right side 25.5 Optional Side Wall Panel (1) specify left or right For blowers (see page 32 For base cabinets (see page 23) 18 Optional Side Wall Panel (1) specify left or right Rear Wall Panel (consult factory for details) Vapor Proof Light & Switch Blower Switch (blower not included) Type 304 stainless steel Side Wall Panel (fiberglass) 36 h X 25 w, kit includes one wall panel and hardware Rear Wall Panel (consult factory for details) Vapor Proof Light & Switch Blower Switch (blower not included) Corner Composite Resin Worksurface Comes dished to contain spillage Corner Table Features welded steel construction

35 Laboratory Emergency /Shower Decontamination Booth Full body emergency shower & eye / face wash, both with immediate response activation handle. Drench Shower Delivers full body shower and eye-wash while protecting the laboratory from water and chemical damage. Overhead drench shower is pull rod activated for immediate response and ease of use. Eye / Face Wash The rear wall mounted eye and face wash, features a yellow ABS plastic bowl, with two large plastic heads, and a push plate operated stay open ball valve. 90 Plumbing valve extends 5 above top Safety First Frosted Vinyl Strip Curtain Provides for easy access into booth while containing contaminated water splash. Grab Bar Support victim and rescue personnel during decontamination wash down. (located on both sides) Fiberglass Floor Grate Flow through Non-slip fl oor grate Plumbing extends 5 at rear Drain can be plumbed either horizontally out the rear or vertically out the bottom of the shower. Note: OSHA & ANSI require that 5 emergency shower is to be located within 10 seconds walking time from the hazardous site location Emergency Drench Shower Eye/Face Wash and Decontamination Booth Booth is equipped with a pull rod activated, overhead drench shower and rear wall mounted eye/ face wash. The emergency shower booth (40 W x 36 D x 90 H) is constructed of molded, seamless, white fi berglass for containment and superior chemical resistance. Booth includes nonslip steps, safety markings, and fi nished white exterior side panels,and signage to clearly signify a safety shower. 1-1/4 IPS inlet piped to shower and eye/face wash with a 3 diameter drain outlet. Specify vertical down drain or horizontal rear drain Emergency Shower Accessories (optional) Alarm Horn & Light Audible warning sound when system is activated by fl ow switch. Top mounted visual warning light when system is activated Hand Held Body Wash squeeze valve nozzle on 8 coiled hose and bracket. Can be used to rinse all body parts while victim is sitting or lying down. Wall or hood mounted, 3/8 NPT, barrier free. Cat Swing-Out Eye Wash Deck mounted next to sink. Activates when pivoted. 1/2 NPT. Barrier free Hand Held Eye/Face & Body Wash Mounted on the front side-wall of the fume hood. Includes 8 hose and surface escutcheon. 3/8 NPT. barrier free

36 MODULAR CLEAN LABS Sized to suit your space requirements, pre-engineered for prompt on site assembly. Equipped with HVAC system, lighting & electrical service to specs. HEPA filtered supply air to suit your modular clean lab applications. HEMCO pre-engineered modular construction for prompt on-site assembly to meet lab space requirements, easily expanded and relocated to suit future Lab Planning needs providing space and energy savings, Now and in the future. 36

37 Modular Clean Labs Made in the U.S.A. HEMCO Modular Clean Lab Room Structures are innovative, pre-engineered modular laboratory workspaces with HEPA filtered supply air, built to your exact process, size and design requirements, for ventilation and safety. 6 X 8 QC Lab w/base floor Modular HEPA Clean Labs and Applications Industrial Quality Control Laboratory Hazardous Materials Testing CMM / Calibration Lab Controlled Environment Rooms Designated Control Rooms Additional Lab Space As technologies change, companies need facilities that can immediately be put into use or quickly adapt with a minimum amount of installation, time, and cost. The Modular Clean Lab features a pre-engineered modular wall panel system that is a cost effective and time efficient alternative to traditional construction. It gives you a fully equipped, high quality enclosure that is easily expanded or relocated as needs change. Determine where the room should be located, assemble the Modular Clean Lab, connect services and start your process. The Modular Clean Lab can fi t a wide range of applications. Wall panel options are available to meet thermal, chemical resistance, sound, and fi re control requirements. Room roof panels can offer load bearing capacity and suspended ceiling systems are available for pressurized overhead supply plenums. 8 X 12 Calibration Lab Complete environmental control systems can be supplied to meet your precise specifi cations. Temperature, humidity, room pressure, and variable exhaust control packages are engineered into a convenient and versatile control panel. Modular Clean Labs can be shipped knocked-down to fi t through a standard doorway for easy on-site erection. If desired, it can be shipped pre-assembled for turnkey operation complete with laboratory fume hoods, furniture, and all component equipment to meet your laboratory requirements. 10 X 16 Clean Lab You can detail your specifi c requirement on our convenient specifi cation planner. Request an Innovative Modular Labs and Rooms catalog at ModuLab Floor Plans (6 x 8 ) (8 x 8 ) (8 x 12 ) (8 x 16 ) HEMCO ModuLab is supplied standard with the walls, ceiling, 8 wide horizontal slide aluminum framed glass door with (1) 48 wide panel sliding and (1) 48 wide panel fixed, and ceiling mounted vapor proof fluorescent lighting. Optional lab furniture, countertops (yellow), fume hood (orange), sink and gooseneck faucet (green) are available to meet your specific requirements. See page 7 for reference and download a Plan-A-Lab layout specification form on our website at: 37

38 Vented Exhaust Enclosures Project: Stanford University Custom Enclosure features seismic levelers, tables can be manufactured to your specifications. EnviroMax Vented Exhaust Enclosures protects personnel A Vented Exhaust Enclosure offered in Unitized & Modular Designs for exhausting fumes from Robotic & Automated processes Designed to protect personnel from potentially hazardous fumes, vapors and odors. The enclosure can connect to in-house exhaust system or a dedicated exhaust blower, to provide the internal negative pressure needed to safely remove hazardous fumes from the work area. Air supply into the enclosure is supplied from the surrounding lab environment. EnviroMax Options Access on any or all sides Multi-Plug strips Exhaust blowers Vertical slide or hinged doors Base cabinets Exhaust HEPA or carbon fi lters Other materials of construction Anodized aluminum & stainless steel framing Plumbing and electrical service fi xtures Airfl ow alarms Support benches & work surfaces Accessories Contact us for custom enclosures built to your exact specifications, for a EnviroMax Specification sheet visit: 38

39 Unitized Construction Sizes Width Depth Height available from any or all sides. Vent duct sized to airfl ow requirements Pre-wired electrical connection to single point junction box. Under the bench storage and shelving designed to suit your requirements Note: Custom sizes are welcomed. Unitized EnviroMax Vented Exhaust Enclosure Superstructure is welded steel framework with chemical resistant white powder coated finish. Side and rear walls are of clear acrylic or tempered glass. Ceiling is constructed of molded composite resin with the outlet duct connection collar sized for desired air volume. Slotted ceiling baffle allows air to flow evenly through the interior area into the exhaust plenum. The front of the enclosure features horizontal sliding shatter-proof clear viewing panels, (4) panels on (2) tracks allowing access at any position. Fluorescent light is factory installed and sealed behind a clear lens. Light switch is mounted on the front post. Provides an economical and flexible work space that exceeds stringent contamination requirements. All electrical components are U.L. listed. Modular Construction Sizes Width Depth Height Vented Exhaust Enclosures Unitized EnviroMax Vented Exhaust Enclosure sizes 4, 5, 6, and 8 wide by 30 & 36 deep by 46 high Unitized design with depth of 30 and 36 to allow passage through door ways for easy on-site setup. Viewing from all four sides of the enclosed system. Access to interior of enclosure, Modular EnviroMax Vented Exhaust Enclosure sizes 6, 8, 10 & 12 wide by 48 & 60 deep by 46 high Modular design with depth of 48 or 60 requires on-site assembly prior to setup and vent ducting. Pre-wired electrical connection to single point junction box. Work surface and support benches and cabinets sized to specifi cations. Provides an environment free of contamination for sensitive processes. Note: Custom sizes are welcomed. Modular EnviroMax Vented Exhaust Enclosure Superstructure is welded steel framework with chemical resistant white powder coated fi nish. Side and rear walls are of clear acrylic or tempered glass. Ceiling is constructed of molded composite resin with the outlet duct connection collar sized for desired air volume. Slotted ceiling baffl e allows air to be drawn out evenly across the width of the interior into the exhaust plenum. The front of the enclosure features horizontal sliding tempered glass panels, (4) panels on (2) tracks allowing access at any position. Fluorescent light is factory installed and sealed behind a clear lens. Light switch is mounted on the front header panel. All electrical components are U.L. listed. EnviroMax Sash Options Project: National Forensics & Coroners Complex, Canada EnviroMax enclosure, unitized 120 wide X 36 deep X 48 high, with custom acid storage cabinets Project: National Forensics & Coroners Complex,Canada EnviroMax Modular enclosure size: 60 wide X 60 deep X 96 high with work surface & 60 wide X 60 deep X 24 high support table HORIZONTAL MOVING SASHES The standard sash for EnviroMax. The maximum sash opening for the horizontal sash is 1/2 that of the vertical sashes. The smaller opening, means less air exhausted resulting in energy savings. OPTIONAL HINGED MOVING SASHES Optional sash for Enviromax. The sash may be hinged vertical rising or horizontal open for maximum access thru the fume chamber. OPTIONAL COUNTER BALANCED VERTICAL MOVING SASHES The optional sash for Enviromax. The sash may be lifted to the completely open position for maximum access tho the fume chamber. Sash stops available. 39

40 Request a free brochure At and browse the entire selection of HEMCO Laboratory Equipment National Society of Professional Engineers ASHRAE American Society of Heating Refrigeration and Air-Conditioning Engineers R Scientific Equipment and Furniture Association Founding Member American Society of Mechanical Engineers U.S. Green Building Council Platinum Member Association of Energy Engineers Made In The U.S.A. Scan the Code to Visit UniFlow Laboratory Fume Hoods Brochure UniMax Large Floor Mount Walk-In Fume Hoods Brochure EnviroMax Enclosures for Robotic and Automated Lab Processes Modular Clean Labs Brochure Laboratory Ventilation Brochure HEMCO Corporation 711 South Powell Road Independence, MO HEMCO ISO 9001:2008 Certified Company Phone (800) LPS-06.16