INVITATION FOR BID T CHILLER, AHU, AND FCU S FOR PATY HALL

Transcription

1 INVITATION FOR BID T CHILLER, AHU, AND FCU S FOR PATY HALL ADDENDUM # 1 03/15/2013 The IFB may be found at NO CHANGE TO BID OPENING DATE: BID OPENS MARCH 20, 2PM Please note the changes in quantities in Section C of the revised quote page, as well as, new spec sheets which you will find as part of this addendum.

2 10.0 REVISED QUOTE SHEET NOTE: THE TOTAL COST MUST INCLUDE PRODUCT AND SHIPPING COST. DO NOT LIST SHIPPING AS A SEPARATE CHARGE. QUOTE PRICES FOB THE UNIVERSITY OF ALABAMA, PREPAID AND ALLOWED. NOTE: CHILLER MUST ARRIVE NO LATER THAN JUNE 28, 2013 AIR HANDLER MUST ARRIVE NO LATER THAN MAY 17, 2013 FAN COIL UNITS MUST ARRIVE NO EARLIER THAN MAY 13, 2013 AND NO LATER THAN MAY 17, 2013 SECTION A: CHILLER PURCHASE ITEM NO. QTY. DESCRIPTION TOTAL COST 1. 1 EA. AIR COOLED CHILLER, SCROLL $ COMPRESSOR MODEL NO. CGAM052 W/ STARTUP AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO. SECTION A: GRAND TOTAL $ SECTION B: OUTDOOR AIR HANDLING UNIT ITEM NO. QTY. DESCRIPTION TOTAL COST 2. 1 EA. OSA-4 PERFORMANCE CLIMATE $ CHANGER MODEL NO. CSAA014UB AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO. SECTION B: GRAND TOTAL $ SECTION C: FAN COIL AIR CONDITIONING UNITS ITEM NO. QTY. DESCRIPTION TOTAL COST EA. FCU1-1~280 FAN COIL AIR CONDITIONER $ MODEL NO. FCDB040 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO.

3 SECTION C: FAN COIL AIR CONDITIONING UNITS CONT. ITEM NO. QTY. DESCRIPTION TOTAL COST 4. 5 EA. FCU2-1~5 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB040 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO EA. FCU2-6~12 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB040 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO EA. FCU3-1~10 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB060 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO EA. FCU3-11 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB060 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO EA. FCU4-1 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB100 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO. SECTION C: GRAND TOTAL $ WARRANTY INFORMATION:

4 U of A Paty Hall FCU Replacements March 13, 2013 Tag Data - Fan Coil Air Conditioning Units (Qty: 310) Item Tag(s) Qty Description Model Number A1 FCU1-1~ Fan Coil Air Conditioners (UniTrane) FCDB040 A2 FCU2-1~5 5 Fan Coil Air Conditioners (UniTrane) FCBB040 A3 FCU2-6~12 7 Fan Coil Air Conditioners (UniTrane) FCBB040 A4 FCU3-1~10 10 Fan Coil Air Conditioners (UniTrane) FCBB060 A5 FCU Fan Coil Air Conditioners (UniTrane) FCBB060 A6 FCU4-1 1 Fan Coil Air Conditioners (UniTrane) FCBB100 Product Data - Fan Coil Air Conditioning Units All Units Fan Coil 115v/60hz/1ph Color to be selected from Trane Standard Colors by the Architect Free discharge fan motor 3 row cooling/heating coil IAQ Drain Pan Manual air vent With disconnect switch 1" MERV 8 filter Factory Installed Ball Valve package (supply) & Manual circuit setter return, P/T supply/return ports, Unions pipe connections, and balance fitting in bypass line. Tracer ZN 010 Wall mounted temperature sensor (set point, OALMH) (Fld) Condensate overflow detection Item: A1 Qty: 280 Tag(s): FCU1-1~280 Horizontal cabinet Size 040 With piping, left hand connection Bottom stamped louver return Front bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A2 Qty: 5 Tag(s): FCU2-1~5 Vertical cabinet Size 040 With piping, right hand connection Toe space return inlet without grille Top bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A3 Qty: 7 Tag(s): FCU2-6~12 Vertical cabinet Size 040 With piping, left hand connection Toe space return inlet without grille Top bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A4 Qty: 10 Tag(s): FCU3-1~10 Vertical cabinet Size 060 With piping, right hand connection Toe space return inlet without grille Top bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A5 Qty: 1 Tag(s): FCU3-11 Vertical cabinet Size 060 Equipment Submittal Page 4 of 29

5 U of A Paty Hall FCU Replacements March 13, 2013 With piping, left hand connection Toe space return inlet without grille Top bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A6 Qty: 1 Tag(s): FCU4-1 Vertical cabinet Size 100 With piping, right hand connection Front bar grille return Top bar grille supply 3 way, 2 position, normally closed (20 psig) cooling control valve Equipment Submittal Page 5 of 29

6 INVITATION FOR BID ATTENTION: This is not an order. Read all instructions and terms and conditions carefully. INVITATION NO.: T URETURN ALL COPIES OF BIDS TO: Issue Date: 03/11/2013 THE UNIVERSITY OF ALABAMA PURCHASING DEPARTMENT Title: Chiller, AHU, and FCU's for Paty Hall (Street Address) 1101 Jackson Ave Suite 3000 Tuscaloosa, Alabama Buyer: Phone: Eric Dickey (205) OR (Mailing Address) Box Tuscaloosa, Alabama PHONE: (205) FAX: (205) Bid Responses may UNOTU be faxed or ed. 1BIMPORTANT: SEALED BIDS MUST BE RECEIVED BY 2:00 P.M. CST TIME Bid number and opening date must be clearly marked on the outside of all bid packages. 1. Pursuant to the provisions of the State of Alabama Competitive Bid Law, Section and/or 39-2, rules and regulations adopted there under sealed bids will be received on the items noted herein by The University of Alabama Purchasing Department until the date and time stated above. In accordance with Alabama State Bid Law Section , where applicable, the University reserves the right to enter into negotiations within thirty (30) days of the bid opening. 2. The University s HUGeneral Terms and ConditionsU and HUInstructions to BiddersUH, apply to this Solicitation and shall become a part of any contract issued hereunder. 3. For purposes of this Solicitation, the Solicitation documents shall consist of the following components: a) Invitation for Bid and any Addenda; b) HUGeneral Terms and ConditionsUH; c) HUInstructions to BiddersU In the event that any provision of the component parts of the Solicitation conflicts with any provision of any other component parts, the component part first enumerated shall govern. 4. This Agreement and any disputes hereunder shall be governed by the laws of the State of Alabama without regard to conflict of law principles. CERTIFICATION PURSUANT TO ACT NO Alabama law (section , code of Alabama 1975) provides that every bid submitted and contract executed shall contain a certification that the vendor, contractor, and all of its affiliates that make sales for delivery into Alabama or leases for use in Alabama are registered, collecting, and remitting Alabama state and local sales, use, and/or lease tax on all taxable sales and leases in Alabama. By submitting a response to this solicitation, the bidder is hereby certifying that they are in full compliance with Act No ; they are not barred from bidding or entering into a contract pursuant to , and acknowledges that The University of Alabama may declare the contract void if the certification is false. DISCLOSURE STATEMENT 1. If you or any owner, officer, partner, board or director member, employee, or holder of more than 5% of the fair market value of your firm or any member of their households is an employee of The University of Alabama, this information must be included in your solicitation response. Failure to disclose this information in your response may result in the elimination of your proposal from evaluation. 2. If you or any owner, officer, partner, board or director member, employee, or holder of more than 5% of the fair market value of your firm or any member of their households is an employee of The University of Alabama; and you or your firm is awarded a contract as a result of this solicitation, then within ten (10) days after the contract is entered into, you agree to file a copy of that contract with the State of Alabama Ethics Commission in accordance with Code of Alabama, Section and upon request by the University furnish evidence of such filing. 3. By accepting payments agreed to in any purchase order resulting from this bid, Contractor certifies that to its knowledge no University employee or official, and no family members of a University employee or official, will receive a benefit from these payments, except as has been previously disclosed, in writing, to the University on the Disclosure Statement of Relationship Between Contractors/Grantees and Employees/Officials of The University of Alabama. AUTHENTICATION OF BID AND STATEMENT OF NON-COLLUSION AND NON-CONFLICT OF INTEREST I hereby swear (or affirm) under the penalty for false swearing as provided in Code of Alabama that 1. In accordance with Code of Alabama Section , amended 1975 that the attached response has been arrived at independently and has been submitted without collusion with, and without any agreement, understanding or planned common course of action with, any other vendor of materials, supplies, equipment or services described in the Invitation for Bids, designed to limit independent bidding or competition; 2. The contents of the bid or bids have not been communicated by the bidder or its employees or agents to any person not an employee or agent of the bidder or its surety on any bond furnished with the bid or bids and will not be communicated to any such person prior to the official opening of the bid or bids. 3. The bidder is legally entitled to enter into contracts with The University of Alabama and is not in violation of any prohibited conflict of interest, including those prohibited by the Code of Alabama 13A-10-62, as amended I have fully informed myself regarding the accuracy of the statement made above. THIS AREA MUST BE COMPLETED DELIVERY AFTER RECEIPT OF ORDER: NAME OF COMPANY: PHONE: FEDERAL EMPLOYER ID NO.: ADDRESS: FAX: PAYMENT TERMS: ADDRESS: SHIPPING TERMS: F.O.B. DESTINATION PREPAID AND ALLOWED 2BCITY, STATE & ZIP CODE: DATE: QUOTE VALID UNTIL: SIGNATURE: Typed/Printed Name of Signor SIGNATURE REQUIRED: This bid cannot be considered valid unless signed and dated by an authorized agent of the bidder. Type or print the information requested in the spaces provided. R e v i s e d J u n e 4, A n E q u a l O p p o r t u n i t y U n i v e r s i t y

7 INVITATION FOR BID Please Note New Bid Specification and Requirements Indicated Below State of Alabama Immigration Law If the successful bidder is located in Alabama or employs an individual or individuals within the State of Alabama, the successful bidder shall provide a copy of its Employment Eligibility Verification (E-Verify) company profile. To expedite the ordering process, this document may be submitted with the bid response. If the successful bidder is not located in the State of Alabama and does not employ an individual or individuals within the State of Alabama, the successful bidder shall complete and return the Certification of Compliance form included with this Request for Price Quotation (E-Verify company profile is not required). To expedite the ordering process, this document may be submitted with the bid response. If you are not currently enrolled in E-Verify, follow these instructions: Log onto Click Getting Started for information about the program, requirements, and enrollment process. Click Enroll in E-Verify and begin enrollment process. When enrollment process is complete, click Edit Company Profile and print this one-page document. This one-page document must be submitted prior to a contract or purchase order being issued. For further assistance please consult the E-Verify Quick Reference Guide. If you have previously enrolled in E-Verify, follow these instructions: Log onto Click Edit Company Profile and print this one-page document. This one-page document must be submitted prior to a contract or purchase order being issued. The following has been added to the University of Alabama s General Terms and Conditions 35. State of Alabama Immigration Law Pursuant to the State of Alabama Immigration Law, by signing this contract, the contracting parties affirm, for the duration of the agreement, that they will not violate federal immigration law or knowingly employ, hire for employment, or continue to employ an unauthorized alien within the State of Alabama. Furthermore, a contracting party found to be in violation of this provision shall be deemed in breach of the agreement and shall be responsible for all damages resulting therefrom.

8 shall INVITATION FOR BID The University of Alabama requests sealed bids as per attached general and technical specifications or equal unless otherwise specified in the Special Conditions. All Bidders submitting a bid must read all specifications carefully and respond accordingly. Failure to do so may eliminate your bid from consideration due to non-compliance. 1.0 GENERAL SPECIFICATIONS 1.1 All bid responses, technical information and any other attachments furnished to The University of Alabama in response to this request for quotation must be submitted in duplicate (UTHE ORIGINAL BID AND ATTACHMENTS WITH ORIGINAL SIGNATURE AND ONE EXACT COPY OF THE ENTIRE BID RESPONSEU). Bidders who fail to follow this format may be disqualified from the evaluation and award phase of this bid. 1.2 The stated requirements appearing elsewhere in this solicitation shall become a part of the terms and conditions of any resulting contract. Any deviations there from must be specifically defined. If accepted by the University, the deviations shall become part of the contract, but such deviations must not be in conflict with the basic nature of this solicitation. Note: Bidders shall not submit their standard terms and conditions or purchase order terms as exceptions to or modification of the terms and conditions of this solicitation. Each exception to or modification of a University term and condition shall be individually listed by the bidder. Failure to follow this instruction may result in the determination that a bid submission is non-responsive to a solicitation and the rejection of that bid. 1.3 The issuance of a University Purchase Order (P#) or a signed Contract document Uis requiredu to constitute a contract between the successful Bidder and the University which shall bind the successful Bidder to furnish and deliver the commodities ordered at the prices, terms and conditions quoted and in accordance with the specifications of this Solicitation as well as the terms and conditions of the University s Purchase Order or Contract. No shipments are to be made to The University of Alabama without the issuance of a Purchase Order (P#). (Bidders are not to accept or ship items against a requisition number R #.) 1.4 Any questions concerning these specifications should be directed to the Buyer listed on the signature page. 1.5 No department, school or office at the University has the authority to solicit or receive official Solicitations nor authorize Solicitation or Contract changes other than the Purchasing Department. All solicitations are issued under the direct supervision of the Associate Director for Purchasing and in complete accordance with the State of Alabama Bid Law, Section and University policies and procedures. 1.6 The terms and conditions included in this Solicitation along with any addenda, any University contract and/or University purchase order(s) issued referencing this Solicitation, the University s HUGeneral Terms and Conditions UH, HUInstructions to Bidders UH constitute the entire and exclusive Contract between the University and the successful Bidder. 1.7 State of Alabama Immigration Law If the successful bidder is located in Alabama or employs an individual or individuals within the State of Alabama, the successful bidder shall provide a copy of its Employment Eligibility Verification (E-Verify) company profile. To expedite the ordering process, this document may be submitted with the bid response. If the successful bidder is not located in the State of Alabama and does not employ an individual or individuals within the State of Alabama, the successful bidder shall complete and return the Certification of Compliance form included with this Request for Price Quotation (E-Verify company profile is not required). To expedite the ordering process, this document may be submitted with the bid response.

9 INVITATION FOR BID If you are not currently enrolled in E-Verify, follow these instructions: Log onto Click Getting Started for information about the program, requirements, and enrollment process. Click Enroll in E-Verify and begin enrollment process. When enrollment process is complete, click Edit Company Profile and print this one-page document. This one-page document must be submitted prior to a contract or purchase order being issued. For further assistance please consult the E-Verify Quick Reference Guide. If you have previously enrolled in E-Verify, follow these instructions: Log onto Click Edit Company Profile and print this one-page document. This one-page document must be submitted prior to a contract or purchase order being issued. 2.0 QUALIFICATIONS AND STANDARDS Due to the importance of maintaining a safe University environment, it is imperative that the successful bidder meet certain qualifications that will guarantee The University of Alabama the successful Bidder is qualified to furnish and deliver products, equipment and services or furnish, deliver, install, service and/or repair equipment whichever is applicable as required in this Solicitation. In order for Bidders to qualify, the following requirements must be fulfilled: 2.1 The Bidder must provide, in writing, a statement that the Bidder has been regularly engaged in business for a minimum three (3) years engaging in furnishing, delivering, servicing, repairing and installing, equipment, goods, or services required in this Solicitation. In lieu of the minimum number of years in business, a performance bond may be submitted in the amount of one hundred (100 %) per cent of the contract price. This bond will be used to secure the completion of the project should the successful Bidder default for any reason. Failure to comply with this requirement may eliminate your bid response from consideration. 2.2 Each bidder required to provide a bond, shall submit a letter from a bonding agent licensed to do business in the State of Alabama stating that if the bidding company is the successful bidder, said bonding agent will furnish a 100% performance and payment bond covering and including products and service for the duration of the contract period. Said bond shall be subject to the approval and acceptance of The University of Alabama. The bond must be furnished to the University Purchasing Department within forty-eight (48) hours after receipt of the purchase order. The premium of the bond shall be paid by the successful bidder. Failure to provide the bond letter or bond will eliminate your bid from consideration in the bid award. 3.0 REFERENCES References must include at least three (3) other universities, institutions or businesses, which the bidder has successfully provided products, services or installation of equipment similar to those required in this Solicitation in terms of manufacturer, size, features, service or type of installation. The references must include company name, address, project/delivery date, contact name, phone number, and address. 4.0 PRODUCT SPECIFICATIONS Specify all terms and conditions of the warranties associated with your products with your bid response.

10 unless for INVITATION FOR BID 5.0 PRICE QUOTATION 5.1 IMPORTANT: It is required that the PRICE QUOTATION SHEET(S) furnished with this Request for Price Quotation be completed and submitted with your proposal. DO NOT send generated price lists as your bid. Failure to comply with this request may eliminate your bid from consideration in the bid award. 5.2 All prices shall be quoted furnish and install (if applicable) FOB The University of Alabama, Tuscaloosa, AL prepay and allowed. Unit prices quoted must include any and all shipping and handling charges. Any freight claims will be the responsibility of the Bidder. The successful Bidder must transport at the time of set-up, the equipment and supplies necessary for this installation to campus. No direct shipments will be accepted. 5.3 It is the Bidder s responsibility to verify any information, measurements and obtain any clarifications prior to submitting the bid response. The University is not liable for any errors or misinterpretations made by the Bidder in response to this Solicitation. 5.4 The successful Bidder under the specifications required in this Solicitation shall furnish at its expense all equipment, labor, tools, supplies, transportation, insurance and other expenses necessary to fully perform any phase of the requirements of this Solicitation. 5.5 Quote prices firm for a period of ninety (90) days following the bid opening date unless otherwise stated in the Special Conditions. Bids that do not guarantee pricing firm for this period may be eliminated. Failure to quote the term for which your prices will remain firm may eliminate your bid from consideration. 5.6 The quoted price must include but not be limited to all cables, wires, connectors, etc. to make a complete functioning unit unless specifically stated in the special conditions. 5.7 Include with your bid response complete details of your company s Return Merchandise policy, including, but not limited to, amount of any restocking fee required, procedures, limitations, contact person and phone number. While the University does not enter into any purchase with the intent to return items ordered, we do require this information be included with your bid response. Failure to include this information may be grounds for elimination of your bid from consideration. 6.0 DELIVERY, INSTALLATION AND TRAINING REQUIREMENTS 6.1 Proposed delivery dates shall be stated in number of calendar days after receipt of order. 6.2 All items must be delivered directly to the University by the successful Bidder and placed according to the instructions supplied by the University. 7.0 INSURANCE 7.1 See HUGeneral Terms and Conditions UH general Insurance Requirements, Additional Insurance requirements may be listed in the Special Conditions Section. 7.2 The successful Bidder shall provide the University Purchasing Department a certificate of insurance listing the required types of insurance and minimum liabilities specified in the HUGeneral Terms and Conditions UH otherwise modified in the Special Conditions. 7.3 The certificate must be received by The University of Alabama Purchasing Department within three (3) days of request. Failure to comply with this request may eliminate your bid from consideration in the bid award. 7.4 The University reserves the right to terminate any resulting contract, if the Bidder fails to keep these policies in force for the above amounts or for the duration of the contract period. 7.5 The umbrella policy must be listed on the insurance certificate with an explanation of the coverage.

11 INVITATION FOR BID 8.0 RESTRICTIONS ON COMMUNICATIONS WITH UNIVERSITY STAFF From the issue date of this Solicitation until a Contractor is selected and a contract award is made, Bidders are not allowed to communicate about the subject of the IFB with any University administrator faculty, staff, or members of the Board of Trustees except: The Purchasing Department representative, any University Purchasing Official representing the University administration, or others authorized in writing by the Purchasing Office and University Representatives during Bidder presentations. If violation of this provision occurs, the University reserves the right to reject the Bidder s response to this Solicitation.

12 INVITATION FOR BID 9.0 SPECIAL CONDITIONS 9.1 The University of Alabama is requesting sealed bids for Chiller, AHU, and FCU s for Paty Hall per attached Technical Specifications/Quotation Sheet or equal. 9.2 Chiller shall have a full five (5) years complete parts, labor, and refrigerant warranty from final acceptance by the University. AHU and FCU s shall have a one (1) year parts and labor warranty from final acceptance by the University. Replacements of any defective items are to be provided by the successful bidder at no charge to the University during the period of guarantee. 9.3 The chiller manufacturer shall supply to The University of Alabama two (2) complete sets of service and operation software/manuals for chiller. 9.4 The Chiller manufacturer will be required to include startup with their unit once all installation has been completed.

13 INVITATION FOR BID 10.0 QUOTE SHEET NOTE: THE TOTAL COST MUST INCLUDE PRODUCT AND SHIPPING COST. DO NOT LIST SHIPPING AS A SEPARATE CHARGE. QUOTE PRICES FOB THE UNIVERSITY OF ALABAMA, PREPAID AND ALLOWED. NOTE: CHILLER MUST ARRIVE NO LATER THAN JUNE 28, 2013 AIR HANDLER MUST ARRIVE NO LATER THAN MAY 17, 2013 FAN COIL UNITS MUST ARRIVE NO EARLIER THAN MAY 13, 2013 AND NO LATER THAN MAY 17, 2013 SECTION A: CHILLER PURCHASE ITEM NO. QTY. DESCRIPTION TOTAL COST 1. 1 EA. AIR COOLED CHILLER, SCROLL $ COMPRESSOR MODEL NO. CGAM052 W/ STARTUP AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO. SECTION A: GRAND TOTAL $ SECTION B: OUTDOOR AIR HANDLING UNIT ITEM NO. QTY. DESCRIPTION TOTAL COST 2. 1 EA. OSA-4 PERFORMANCE CLIMATE $ CHANGER MODEL NO. CSAA014UB AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO. SECTION B: GRAND TOTAL $ SECTION C: FAN COIL AIR CONDITIONING UNITS ITEM NO. QTY. DESCRIPTION TOTAL COST EA. FCU1-1~282 FAN COIL AIR CONDITIONER $ MODEL NO. FCDB040 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO.

14 INVITATION FOR BID SECTION C: FAN COIL AIR CONDITIONING UNITS CONT. ITEM NO. QTY. DESCRIPTION TOTAL COST EA. FCU2-1~14 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB040 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO EA. FCU2-15 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB040 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO EA. FCU3-1~11 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB060 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO EA. FCU3-12 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB060 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO EA. FCU4-1 FAN COIL AIR CONDITIONER $ MODEL NO. FCBB100 AS PER ATTACHED SPECIFICATIONS OR EQUAL MANUFACTURER: MODEL NO. SECTION C: GRAND TOTAL $ WARRANTY INFORMATION:

15 Submittal Prepared For: Whitaker & Rawson Inc 3332 Old Montgomery Highway Homewood, AL Sold To: University of Alabama Date: March 07, 2013 Customer P.O. Number: Customer Project Number: Job Number: Job Name: U of A Paty Hall Chiller Replacement Trane U.S. Inc. dba Trane is pleased to provide the enclosed submittal for your review and approval. Product Summary Qty Product 1 Air-Cooled Scroll The attached information describes the equipment we propose to furnish for this project, and is submitted for your approval. Chandler McGarrah Trane 1030 London Drive, Suite 100 Birmingham, AL Phone: (205) Fax: (205) J:\JOBS\50\81408\4\U of A Paty Hall Chiller Replacement Submittal.doc

16 Table Of Contents Product Summary... 1 Air-Cooled Scroll (Item A1)... 4 Tag Data... 4 Performance Data... 4 Mechanical Specifications... 6 Unit Dimensions... 8 Weight, Clearance & Rigging Diagram Accessory Field Wiring... 20

17 U of A Paty Hall Chiller Replacement March 07, 2013 Air Cooled Chiller Specification Items: Unit Level 52 Nominal Ton Air Cooled Chiller 208/3 High Efficiency UL Listed ASHRAE 90.1 Compliant AHRI Certified Factory Installed With Freeze Protection (External T-STAT Control) Refrigeration Isolation Valves (Discharge Valve) Factory Provided and Installed Flow Switch Factory Installed ¾ Insulation on Evaporator and Suction Line Lanced Aluminum Fins Wide Ambient Operation from 0F to 125F Performance Based on 30% PG Across the Line Starter Dual High Head Pump with Factory Variable Frequency Drive Single Point Power Connection Factory Installed 140 Gallon Welded Steel Buffer Tank Factory Insulated for Protection to -20F High Fault Rated Control Panel and Circuit Breaker SCR Minimum 10,000A Phase Reversal and Phase Loss Protection Factory Installed Water Strainer Acoustic Option with Low Sound Fans and Compressor Blankets Elastomeric Isolators 5 Year Entire Unit Parts, Labor, and Refrigerant Warranty Factory Startup Shipping - FOB Jobsite Note: Chiller to be provided with 2 independent circuits that can be mechanically and electrically isolated in the event a failure takes place so that one circuit can operate while the other circuit is repaired. Note: Provide additional price to have factory authorized manufacturer s representative to rig, lift, install and make field pipe connections for buffer tank if it is not factory installed. See Mechanical Specification Section (pages 6-7) for the Remainder of the Applicable Air Cooled Chiller Specifications. Equipment Submittal Page 3 of 22

18 U of A Paty Hall Chiller Replacement March 07, 2013 Tag Data - Air-Cooled Scroll (Qty: 1) Item Tag(s) Qty Description Model Number A1 CH-1 1 Air-Cooled Chiller, Scroll Compressors CGAM052 Performance Data - Air-Cooled Scroll Tags CH-1 Capacity (tons) Unit power input (kw) Full load efficiency (EER) 9.4 NPLV (EER) 14.4 IPLV (EER) 15.0 Sound power level (dba) 88 Sound pressure level (dba) 62 Refrigerant R410A Refrigerant charge circuit 1 (lb) 32.0 Refrigerant charge circuit 2 (lb) 32.0 Oil charge circuit 1 (gal) 1.74 Oil charge circuit 2 (gal) 1.74 Evap entering temp (F) Evap leaving temp (F) Evap flow rate (gpm) Min evap flow rate (gpm) Min flow PD evap+strainer (ft H2O) 9.50 Max evap flow rate (gpm) Max flow PD evap+strainer (ft H2O) Evap fluid concentration (%) Evap fluid freeze point (F) 9.30 Evap press drop (ft H2O) Total PD evap+strainer (ft H2O) Evap fouling factor (hr-sq ft-deg F/Btu) Saturated evap temp circuit 1 (F) Saturated evap temp circuit 2 (F) Ambient air temperature (F) Saturated cond temp circuit 1 (F) Saturated cond temp circuit 2 (F) Compressor power input (kw) RLA - compressor 1A (A) LRA - compressor 1A (A) RLA - compressor 1B (A) LRA - compressor 1B (A) RLA - compressor 2A (A) LRA - compressor 2A (A) RLA - compressor 2B (A) LRA - compressor 2B (A) Total airflow (cfm) Number of fans ( ) 4 Fan motor power (kw) 4.60 Total fan FLA (A) Pump size (kw) 3.73 Pump nominal current (A) Expansion tank volume (gal) 5.00 Buffer tank volume (gal) Avail head pressure at water connection (ft H2O) Total PD pump+evap+strainer (ft H2O) Single point power MCA (A) Equipment Submittal Page 4 of 22

19 U of A Paty Hall Chiller Replacement March 07, 2013 Tags CH-1 Single point power MOP (A) Short circuit current rating (A) Number of compressors ( ) 4 Number of circuits ( ) 2 Capacity steps ( ) 4 Shipping weight (lb) Operating weight (lb) Length (in) Width (in) Height (in) Equipment Submittal Page 5 of 22

20 U of A Paty Hall Chiller Replacement March 07, 2013 Mechanical Specifications - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 General Units are constructed of a galvanized steel frame with galvanized steel panels and access doors. Component surfaces are finished with a powder-coated paint. All paint meets the requirement for outdoor equipment of the U.S. Navy and other Federal Government Agencies. This paint finish is durable enough to withstand a 1000-consecutive-hour salt spray application in accordance with standard ASTMB117. Each unit ships with full operating charges of refrigerant and oil. Compressor and Motor The unit is equipped with four hermetic, direct-drive, 3600 rpm 60 Hz suction gas-cooled scroll compressors. Overload protection is internal to the compressors. The compressor includes: centrifugal oil pump, oil level sight glass and oil charging valve. Each compressor will have compressor heaters installed and properly sized to minimize the amount of liquid refrigerant present in the oil sump during off cycles. Unit-Mounted Starter The control panel is designed per UL The starter is in an across-the-line configuration, factory-mounted and fully pre-wired to the compressor motor and control panel. Typically, Trane scroll compressors are up to full speed in one second when started across-the-line. A factory-installed, factory-wired 820 VA control power transformer provides all unit control power (120 Vac secondary) and Trane CH530 module power (24 Vac secondary). A molded case high interrupting capacity circuit breaker, factory pre-wired with terminal block power connections and equipped with a lockable external operator handle, is available to disconnect the chiller from main power. Power Connection Power connections include main three-phase power and one separate 120V, 15 amp customer provided single phase power connection is required to power the heaters (if used for freeze protection). Short circuit current rating of 65kA is provided. Evaporator Braze plate evaporator is made of stainless steel with copper as the braze material. It is designed to withstand a refrigerant side working pressure of 430 psig (29.6 bars) and a waterside working pressure of 150 psig (10.5 bars). Evaporator is tested at 1.1 times maximum allowable refrigerant side working pressure and 1.5 times maximum allowable water side working pressure. It has one water pass. A water strainer and a flow switch are factory installed. Immersion heaters protect the evaporator to an ambient of -20 F (-29 C). Condenser Air-cooled condenser coils have lanced aluminum fins mechanically bonded to internally-finned copper tubing. The condenser coil has an integral subcooling circuit. The maximum allowable working pressure of the condenser is 650 psig (44.8 bars). Condensers are factory proof and leak tested at 715 psig (49.3 bars). Direct-drive vertical discharge condenser fans are balanced and individually protected. Three-phase condenser fan motors with permanently lubricated ball bearings and external thermal overload protection are provided. A variable speed drive on the first fan of each circuit allows the unit to start and operate with ambient temperatures between 0.0 F and F. Refrigerant Circuits The unit has dual refrigerant circuits. Each refrigerant circuit has Trane scroll compressors piped in parallel with a passive oil management system. A passive oil management system maintains proper oil levels within compressors and has no moving parts. Each refrigerant circuit includes filter drier, electronic expansion valve, liquid line and discharge service valves. Capacity modulation is achieved by turning compressors on and off. The unit has four capacity stages. Unit Controls The microprocessor-based control panel is factory-installed and factory-tested. The control system is powered by a pre-wired control power transformer, and will turn on and off compressors to meet the load. Microprocessor-based Equipment Submittal Page 6 of 22

21 U of A Paty Hall Chiller Replacement March 07, 2013 chilled water reset based on return water is standard. The unit comes with a factory installed flow switch. The Trane CH530 microprocessor automatically acts to prevent unit shutdown due to abnormal operating conditions associated with low evaporator refrigerant temperature and high condensing temperature. If an abnormal operating condition continues and the protective limit is reached, the machine will shut down. The panel includes machine protection for the following conditions: low evaporator refrigerant temperature and pressure, high condenser refrigerant pressure, critical sensor or detection circuit faults, lost communication between modules, phase loss, phase reversal, over temperature protection, external and local emergency stop, and loss of evaporator water flow. When a fault is detected, the control system conducts more than 100 diagnostic checks and displays results. The display will identify the fault, indicate date, time, and operating mode at time of occurrence, and provide type of reset required and a help message. Data contained in available reports includes: water and air temperatures, refrigerant pressures and temperatures, flow switch status, EXV position, and compressor starts and run-time. All necessary settings and setpoints are programmed into the microprocessor-based controller via the operator interface. The controller is capable of receiving signals simultaneously from a variety of control sources, in any combination, and priority order of control sources can be programmed. Communications LonTalk (LCI-C) communications capabilities are available with communication link via single twisted-pair wiring to factory-installed and tested communication board. This option will support the functionality required to obtain Lon Mark certification. Pump Pump package includes: two pumps, expansion vessel, drainage valve, shut-off valve at entering and leaving connections. The pump package is single point power integrated into the chiller unit power with a separate factory wired control panel and separate power for freeze protection. The control of the pump is integrated into the chiller controller. The CH530 displays evaporator pump starts and run-times. Freeze protection down to an ambient of -29 C (-20 F) is included as standard. The cold parts of the pump package will be insulated. Designed with one redundant pump, it is controlled to operate both pumps through a lead/lag and failure/recovery functionality. The pump offering can be for applications that have short water loops, de-coupled systems or for applications where the integrated chiller pump could serve the entire loop volume. A variable speed drive is installed in an additional panel to control the pump. The inverter is adjusted upon start up to balance the system flow and head requirements. The purpose is to save on wasted pump energy caused by a traditional balancing valve. Buffer Tank The water tank is factory-installed for easy installation at the building site and it is engineered for continuous flow. Tank construction is welded steel; it is powder coated, fully insulated and designed with freeze protection down to -20 F (-29 C). It is rated with a waterside working pressure of 150 psig and tested at 225 psig.. Water connections are grooved pipe. The purpose of the tank is to increase the chilled water circuit inertia, which is necessary with short water loops. A high circuit inertia reduces the compressor cycling to increase the compressor life span and allow for more precise water temperature accuracy. It also saves energy as compared to hot gas bypass. Comprehensive Acoustic Package Acoustical treatment consisting of low noise fans and compressor acoustical wraps Isolators Molded elastomeric isolators, sized to reduce vibration transmission to the supporting structure when the unit is installed, ship with the chiller. Equipment Submittal Page 7 of 22

22 U of A Paty Hall Chiller Replacement March 07, 2013 Unit Dimensions - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 INLET/OUTLET WATER CONNECTION SIZE INLET 2.5" (65mm) / OUTLET 3" (80mm) BRAZE PLATE WATER VOLUME/STORAGE 4.1 GAL (15.6 LITERS) TOP VIEW ISOMETRIC VIEW FRONT VIEW RIGHT SIDE VIEW BACK VIEW SIDES AND TOP OF BUFFER TANK REMOVED FOR CLARITY Equipment Submittal Page 8 of 22

23 U of A Paty Hall Chiller Replacement March 07, 2013 Unit Dimensions - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH /16" LIFTING LOCATION 4 PLACES 89 15/16" /16" 134 1/4" RIGHT SIDE VIEW BUFFER TANK Equipment Submittal Page 9 of 22

24 U of A Paty Hall Chiller Replacement March 07, 2013 Unit Dimensions - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 8 1/2" INLET WATER CONNECTION 3 3/16" INCOMING POWER KNOCKOUT OUTLET WATER BRAZE PLATE CONNECTION COMPRESSORS UNIT CONTROL PANEL THIS END OF UNIT COMPRESSORS 32 1/8" 25 3/4" BUFFER TANK PUMP 3 7/16" SIDES AND TOP OF BUFFER TANK REMOVED FOR CLARITY TOP VIEW CONDENSER, CONTROL PANEL AND VSD (WHEN ORDERED) REMOVED FOR CLARITY 6 13/16" Equipment Submittal Page 10 of 22

25 U of A Paty Hall Chiller Replacement March 07, 2013 Unit Dimensions - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 UNIT CONTROL PANEL VSD BOX 34 1/4" 88 3/8" FRONT VIEW 8 9/16" 76 1/4" 84 13/16" Equipment Submittal Page 11 of 22

26 U of A Paty Hall Chiller Replacement March 07, 2013 Unit Dimensions - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 BUFFER TANK VOLUME: gal EXPANSION TANK VOLUME: 5.00 gal SIDES AND TOP OF BUFFER TANK REMOVED FOR CLARITY BACK VIEW 24 1/4" 27 5/16" OUTLET WATER CONNECTION INLET WATER CONNECTION 16 1/8" 19 9/16" Equipment Submittal Page 12 of 22

27 U of A Paty Hall Chiller Replacement March 07, 2013 Unit Dimensions - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 ISOMETRIC VIEW Equipment Submittal Page 13 of 22

28 U of A Paty Hall Chiller Replacement March 07, 2013 Weight, Clearance & Rigging Diagram - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 UNIT CENTER OF GRAVITY LIFTING WEIGHTS W1 W2 W3 W lb lb lb lb SHIPPING WEIGHT lb CG CG in W1 - NEAR SIDE W2 - FAR SIDE in in FRONT VIEW SIDE VIEW CONTROL PANEL END W3 - NEAR SIDE W4 - FAR SIDE Equipment Submittal Page 14 of 22

29 U of A Paty Hall Chiller Replacement March 07, 2013 Weight, Clearance & Rigging Diagram - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 UNIT CLEARANCE 47 1/4" NO OBSTRUCTIONS ABOVE THE CONDENSER 39 3/8" 31 1/2" FOR OBSTRUCTIONS OR MULTIPLE UNITS, REFER TO THE CLOSE SPACING BULLETIN. WORKING CLEARANCE PER NATIONAL ELECTRIC CODE ARTICLE TOP VIEW NO OBSTRUCTIONS RECOMMENDED. Area Required for unit operation, maintenance, and access panel. MORE CLEARANCE MAY BE NEEDED FOR AIRFLOW DEPENDING UPON THE INSTALLATION. 39 3/8" Equipment Submittal Page 15 of 22

30 U of A Paty Hall Chiller Replacement March 07, 2013 Weight, Clearance & Rigging Diagram - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 LIFTING A UNIT WITH EQUAL LENGTH STRAPS WILL NOT PRODUCE A LEVEL UNIT DURING THE LIFT BECAUSE THE CG WILL NOT BE AT THE MIDPOINT BETWEEN THE BASE LIFTING HOLES. THE FOLLOWING ADJUSTMENTS MUST BE MADE TO PRODUCE A LEVEL LIFT: - SINGLE SPREADER BAR LIFTING METHOD IF THE UNIT CG IS CLOSER TO THE CONTROL PANEL, THE STRAPS ON THE CONTROL PANEL SIDE OF THE SPREADER BAR MUST BE ADJUSTED TO BE SHORTER THAN THOSE ON THE OPPOSITE SIDE OF THE SPREADER BAR, ALLOWING THE SPREADER BAR TO MOVE TOWARD THE CONTROL PANEL AND OVER THE UNIT CG. SEVERAL ADJUSTMENTS OF THE STRAP LENGTH MAY BE REQUIRED TO PRODUCE A LEVEL UNIT DURING LIFT. - H-TYPE SPREADER BAR LIFTING METHOD IF THE STRAPS FROM THE H BAR TO THE UNIT BASE ARE THE SAME LENGTH, THE CRANE LIFTING POINT ON THE CENTER WEB OF THE H BAR MUST BE ADJUSTED TO PRODUCE A LEVEL UNIT LIFT. IMPROPER LIFTING AND MOVING! USE SPREADER BAR AS SHOWN IN DIAGRAM. REFER TO INSTALLATION MANUAL OR NAMEPLATE FOR UNIT WEIGHT. REFER TO INSTALLATION INSTRUCTIONS LOCATED INSIDE CONTROL PANEL FOR FURTHER RIGGING INFORMATION. OTHER LIFTING ARRANGEMENTS COULD RESULT IN DEATH, SERIOUS INJURY OR EQUIPMENT DAMAGE. UNIT RIGGING ISOMETRIC VIEW 23 3/4" 89 7/8" Equipment Submittal Page 16 of 22

31 U of A Paty Hall Chiller Replacement March 07, 2013 Accessory - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 UNIT SIZE /16" CUSTOMER WIRE SELECTION TABLE POWER WIRE CONNECTION TO CIRCUIT BREAKER (1Q1) UNIT EFF VOLTAGE CIR 1 & 2 (SINGLE POINT POWER) LUG WIRE SIZE RANGE (PER PHASE) HIGH 200 (2 MAX Conductors per phase) 2/0-500MCM 75 1/2" FRONT VIEW CUSTOMER CONTROL WIRING 12 KNOCKOUTS 4 1/2" 2 15/16" 1 5/16" 4 5/16" 5 7/8" 7 7/16" 9" BOTTOM VIEW SHORT CIRCUIT RATING ISOMETRIC VIEW CUSTOMER POWER CONNECTION 8 7/16" 11/16" 11 15/16" 24 1/2" 65kA Equipment Submittal Page 17 of 22

32 U of A Paty Hall Chiller Replacement March 07, 2013 Accessory - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 UNIT SIZE 052 MOUNTING LOCATIONS & POINT LOAD WEIGHTS lb lb lb lb N/A N/A TOTAL OPERATING WEIGHT lb MOUNTING HOLE DIAMETER 19mm DIMENSIONS ARE REFERENCED FROM THE END AND SIDE OF THE UNIT BASE 19 3/8" CONTROL PANEL " /2" TOP VIEW Equipment Submittal Page 18 of 22

33 U of A Paty Hall Chiller Replacement March 07, 2013 Accessory - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 CONTROL PANEL UNIT SIZE MOUNTING LOCATIONS AND ISOLATOR NUMBER RDP-4 BROWN RDP-4 BROWN RDP-4 CHARCOAL RDP-4 CHARCOAL N/A N/A RDP-3 ISOLATORS 9/16" DIA 2 HOLES 3 3/8" 4 5/8" 4 1/8" 5 1/2" 1/2" DIA 1/2" DIA 2 1/2" 1 1/8" 2 7/8" 1/4" 2 3/4" SEE ISOLATOR POINT LOADS FOR DETAILED INFORMATION ON ISOLATOR LOCATIONS. RDP-4 ISOLATORS 9/16" DIA 2 HOLES 5" 6 1/4" 3" 1 5/8" 3/8" Equipment Submittal Page 19 of 22

34 U of A Paty Hall Chiller Replacement March 07, 2013 Field Wiring - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 CONTROL PANEL PAGE 1 OF 2 WARNING HAZARDOUS VOLTAGE! DISCONNECT ALL ELECTRIC POWER INCLUDING REMOTE DISCONNECTS AND FOLLOW LOCK OUT AND TAG PROCEDURES BEFORE SERVICING. INSURE THAT ALL MOTOR CAPACITORS HAVE DISCHARGED STORED VOLTAGE. UNITS WITH VARIABLE SPEED DRIVE, REFER TO DRIVE INSTRUCTIONS FOR CAPACITOR DISCHARGE. FAILURE TO DO THE ABOVE COULD RESULT IN DEATH OR SERIOUS INJURY. INSET "B" 25A H1 25A 26A INSET "B" H1 H2 H3 200V 60HZ 460V 60HZ 1T1 115V 27V OR 110V X1 X2 X3 X V 50HZ UNIT IS FACTORY WIRED AS SHOWN, RECONNECT WIRE 26A TO TERMINALS H2 OR H4 FOR 380V 50HZ OR 415V 50HZ POWER SUPPLIES. 380V 60HZ 220V 50HZ 26A H2 25A H1 575V 60HZ 230V 60HZ 26A 25A 380V H2 H3 H1 H2 26A H3 415V H4 INSET "A" 1 1Q2 L1 A B C L2 L3 EQUIPMENT GROUND A L1 B L2 C A L3 L1 B L2 C L3 6Q2 6Q1 12 A L1 B C A L2 L3 L1 B C L2 L3 USE COPPER CONDUCTORS ONLY! UNIT TERMINALS ARE NOT DESIGNED TO ACCEPT OTHER TYPES OF CONDUCTORS. FAILURE TO DO THE ABOVE COULD RESULT IN EQUIPMENT DAMAGE. 2 Equipment Submittal Page 20 of 22

35 U of A Paty Hall Chiller Replacement March 07, 2013 Field Wiring - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH-1 BUFFER TANK HEATERS HEATERS CIRCUIT 4 CIRCUIT Q7 H 4 43 N 6Q H N 4 1X X X X VDC CUSTOMER PUMP INVERTER SPEED SIGNAL X X A15 COMMUNICATION BOARD (OPTIONAL) LCI-C TO TRACER OR OTHER TRANE REMOTE DEVICE TO NEXT UNIT 3 4 J2 1 2 SHIELDED TWISTED PAIR LEADS SHIELDED TWISTED PAIR LEADS 1A25 ANALOG INPUT/OUTPUT CAPACITY OUTPUT (OPTIONAL) J K5 17 6K F F A13 1A12 DUAL LOW VOLTAGE DUAL LOW VOLTAGE BINARY INPUT BINARY INPUT EMERGENY STOP/ CHILLED WATER PUMP AUTO STOP FAULT INPUT J EQUIPMENT GROUND GND 2-10VDC 1X5-8 1X X X5-5 W3 E-STOP W2 AUTO STOP PUMP 2 PUMP 1 J CONTROL PANEL PAGE 2 OF 2 WARNING HAZARDOUS VOLTAGE! DISCONNECT ALL ELECTRIC POWER INCLUDING REMOTE DISCONNECTS AND FOLLOW LOCK OUT AND TAG PROCEDURES BEFORE SERVICING. INSURE THAT ALL MOTOR CAPACITORS HAVE DISCHARGED STORED VOLTAGE. UNITS WITH VARIABLE SPEED DRIVE, REFER TO DRIVE INSTRUCTIONS FOR CAPACITOR DISCHARGE. FAILURE TO DO THE ABOVE COULD RESULT IN DEATH OR SERIOUS INJURY. USE COPPER CONDUCTORS ONLY! UNIT TERMINALS ARE NOT DESIGNED TO ACCEPT OTHER TYPES OF CONDUCTORS. FAILURE TO DO THE ABOVE COULD RESULT IN EQUIPMENT DAMAGE. Equipment Submittal Page 21 of 22

36 U of A Paty Hall Chiller Replacement March 07, 2013 Field Wiring - Air-Cooled Scroll Item: A1 Qty: 1 Tag(s): CH SINGLE SOURCE POWER IS PROVIDED AS STANDARD ON THESE PRODUCTS, FIELD CONNECTIONS ARE MADE TO 1X1, OR 1Q2. FOR VOLTAGES 200V/60HZ, 220V/50HZ, 380V/60HZ, 460V/60HZ, WIRE 26A SHALL BE CONNECTED TO H2. FOR VOLTAGES 230V/60HZ & 575V/60HZ, WIRE 26A SHALL BE CONNECT TO H3. 400V/50HZ UNIT IS FACTORY WIRED WITH 26A CONNECTED TO H3 - RECONNECT WIRE 26A TO H2 FOR 380V/50HZ, OR H4 FOR 415V/50HZ. H4 IS ONLY AVAILABLE WITH 400V/50HZ PANELS. FIELD CONNECTIONS ARE ONLY MADE IN A CUSTOMER PROVIDED PUMP (PTYP=NONE). THESE CONNECTIONS WILL BE MADE BY THE FACTORY WHEN THE PUMP IS PROVIDED BY THE FACTORY (PTYP=DHHP). CUSTOMER SUPPLIED POWER 115/60/1 OR 220/50/1 TO POWER RELAYS. MAX. FUSE SIZE IS 20 AMPS. GROUND ALL CUSTOMER SUPPLIED POWER SUPPLIES AS REQUIRED BY APPLICABLE CODES. GREEN GROUND SCREWS ARE PROVIDED IN UNIT CONTROL PANEL. WIRED TO NEXT UNIT. 22 AWG SHIELDED COMMUNICATION WIRE EQUIVALENT TO HELIX LF22P RECOMMENDED. THE SUM TOTAL OF ALL INTERCONNECTED CABLE SEGMENTS NOT TO EXCEED 4500 FEET. CONNECTION TOPOLOGY SHOULD BE DAISY CHAIN. REFER TO BUILDING AUTOMATION SYSTEM (BAS) COMMUNICATION INSTALLATION LITERATURE FOR END OF LINE TERMINATION RESISTOR REQUIREMENTS. WIRED TO TRACER OR OTHER TRANE REMOTE DEVICE. 22 AWG SHIELDED COMMUNICATION WIRE EQUIVALENT TO HELIX LF22P RECOMMENDED. THE SUM TOTAL OF ALL INTERCONNECTED CABLE SEGMENTS NOT TO EXCEED 4500 FEET. CONNECTION TOPOLOGY SHOULD BE DAISY CHAIN. REFER TO BUILDING AUTOMATION SYSTEM (BAS) COMMUNICATION INSTALLATION LITERATURE FOR END OF LINE TERMINATION RESISTOR REQUIREMENTS. WIRED TO CUSTOMER CHILLED WATER SET POINT 2-10V OR 4-20mA. WIRED TO CUSTOMER EXTERNAL DEMAND LIMIT 2-10V OR 4-20mA. WIRED TO CUSTOMER 2-10V OR 4-20mA % CAPACITY ANNUNICIATOR. WIRED TO TRACER OR OTHER REMOTE DEVICE. REFER TO CGAM ELECTRICAL SCHEMATIC FOR SPECIFIC ELECTRICAL CONNECTION INFORMATION AND NOTES PERTAINING TO WIRING INSTALLATION. ALL UNIT POWER WIRING MUST BE 600 VOLT COPPER CONDUCTORS ONLY AND HAVE A MINIMUM TEMPERATURE INSULATION RATING OF 90 DEGREE C. REFER TO UNIT NAMEPLATE FOR MINIMUM CIRCUIT AMPACITY AND MAXIMUM OVERCURRENT PROTECTION DEVICE. PROVIDE AN EQUIPMENT GROUND IN ACCORDANCE WITH APPLICABLE ELECTRIC CODES. REFER TO WIRE RANGE TABLE FOR LUG SIZES. ALL FIELD WIRING MUST BE IN ACCORDANCE WITH NATIONAL ELECTRIC CODE AND LOCAL REQUIREMENTS. ALL CUSTOMER CONTROL CIRCUIT WIRING MUST BE COPPER CONDUCTORS ONLY AND HAVE A MINIMUM INSULATION RATING OF 300 VOLTS. EXCEPT AS NOTED, ALL CUSTOMER WIRING CONNECTIONS ARE MADE TO CIRCUIT BOARD MOUNTED BOX LUGS WITH A WIRE RANGE OF 14 TO 18 AWG OR DIN RAIL MOUNTED SPRING FORCE TERMINALS. UNIT PROVIDED DRY CONTACTS FOR THE CONDENSER/CHILLED WATER PUMP CONTROL. RELAYS ARE RATED FOR 7.2 AMPS RESISTIVE, 2.88 AMPS PILOT 1 DUTY, OR 3 HP, 7.2 FLA AT 120 VOLTS 60 HZ, CONTACTS ARE RATED FOR 5 AMPS GENERAL PURPOSE DUTY 240 VOLTS. CUSTOMER SUPPLIED CONTACTS FOR ALL LOW VOLTAGE CONNECTIONS MUST BE COMPATABLE WITH DRY CIRCUIT 24 VOLTS DC FOR A 12 ma RESISTIVE LOAD. SILVER OR GOLD PLATED CONTACTS RECOMMENDED. FIELD CONNECTIONS ARE ONLY MADE IN A CUSTOMER PROVIDED PUMP. THESE CONNECTIONS WILL BE MADE BY THE FACTORY WHEN THE PUMP IS PROVIDED BY THE FACTORY. CUSTOMER SUPPLIED POWER 115V, 60Hz, 1PH. CUSTOMER SUPPLIED 3 PHASE POWER. OPTIONAL FIELD ASSIGNED PROGRAMMABLE RELAYS (STAT=PRLY). CLASS 1 FIELD WIRED MODULE, RELAY AT 120V: 7.2A RESISTIVE 2.88A PILOT DUTY, 1/2 HP 7.2FLA; AT 240VAC: 5 AMPS GENERAL PURPOSE. WIRED TO CUSTOMER 0-10 VDC PUMP SPEED SIGNAL. WHEN FACTORY PROVIDED PUMP IS NOT SELECTED. CUSTOMER MUST SUPPLY SUITABLE PUMP SYSTEM. REFER TO PUMP MANUFACTURER FOR WIRING REQUIREMENTS. THE CONTACTS FOR AUTO STOP AND EMERGENCY STOP SWITCHES ARE JUMPERED AT THE FACTORY BY JUMPERS W2 & W3 TO ENABLE UNIT OPERATION. IF REMOTE CONTROL IS DESIRED, REMOVED THE JUMPERS AND CONNECT TO THE DESIRED CONTROL CIRCUIT. 1A15, LCI MODULE USED WHEN (COMM = LCI). 1A41, BACNET INTERFACE MODULE USED WHEN (COMM = BCNT). Equipment Submittal Page 22 of 22

37 Submittal Prepared For: Whitaker & Rawson Inc 3332 Old Montgomery Highway Homewood, AL Sold To: University of Alabama Date: March 08, 2013 Customer P.O. Number: Customer Project Number: Job Number: Job Name: U of A Paty Hall AHU Replacement Trane U.S. Inc. dba Trane is pleased to provide the enclosed submittal for your review and approval. Product Summary Qty Product 1 Outdoor Performance Climate Changer The attached information describes the equipment we propose to furnish for this project, and is submitted for your approval. Chandler McGarrah Trane 1030 London Drive, Suite 100 Birmingham, AL Phone: (205) Fax: (205) J:\JOBS\50\81408\12\U of A Paty Hall Outdoor AHU Submittal.doc

38 Table Of Contents Product Summary... 1 Performance Climate Changer (Item A1)... 4 Tag Data... 4 Product Data... 4 Performance Data... 5 Mechanical Specifications... 7 As-Built Fan Curve Accessory Field Wiring Field Installed Options - Part/Order Number Summary Performance Climate Changer... 31

39 U of A Paty Hall FCU Replacements March 08, 2013 Air Handling Unit Specification Items: Unit Level Outdoor Application 6in. integral base frame Provide 14 Full Perimeter Roof Curb Units Must Be Listed by UL/C-UL or ETL Less than 1% leakage at +/- 8 TSP L/240 Panel Deflection Unit Panels Shall be Provided with a Mid-Span, No-Through-Metal, Internal Thermal Break. Thermal Break Shall Include Fasteners. All Access Doors Shall be Provided with Thermal Break Construction of Door Panel and Door Frame All Access Doors Shall Have Multiple Composite Door Latches. Spray Injected Foam Insulation With Minimum Thermal Resistance (R) value of 13 ft²-h-ºf/btu Marine LED Lights in Mixing Box, Access Sections, and Fan Wired to Single Switch (Fld Power Wiring) Convenience Outlet (Fld Power Wiring) Shipping - FOB Jobsite Mixing Box Configured with rear 100% outside air intake with rain hood 4 MERV 8 filtration Marine Light Cooling Coil Minimum 8 Row Cooling Coil with Maximum 120 FPF with Stainless Steel Coil Casings and Drain Pans Configured for 100% Outside Air with 30% PG Solution Access Sections Access Section Minimum of 14 for Accessibility. Access Section Must Include Access Door and Marine Light Fans DWDI Housed Airfoil Fan Marine Light 2 Spring Isolation Field Provided VFD Premium Efficiency, Inverter Rated Motor with Shaft Grounding Rings Indirect Gas Fired Heat Section Indirect Fired Gas Heater with Stainless Steel Heat Exchanger 80% Efficiency Gas Heater 10:1 Turn Fully Modulating Turndown Factory Provided Flue Discharge Configured For Front Air Discharge See Mechanical Specification Section (pages 7-10) for the Remainder of the Applicable Air Handling Unit Specifications. Equipment Submittal Page 3 of 31

40 U of A Paty Hall FCU Replacements March 08, 2013 Tag Data - Performance Climate Changer (Qty: 1) Item Tag(s) Qty Description Model Number A1 OSA-4 1 Performance Climate Changer ( CSAA ) CSAA014UB Product Data - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Unit level options Outdoor unit Unit size 14 6in. integral base frame UL listed unit Single metal handle - ganged latches Air mixing section (Pos #1) Air mixing section 4 MERV 8 Filter Door- left side Marine LED light Coil section (Pos #2) Horizontal coolingcoil Stainless steel drain pan Right side - drain connection Right side - coil supply 8 rows 117 Fin spacing Aluminum fins Delta flo H (Hi efficient).016" (0.406mm) copper tubes 1/2in. tube diameter (12.7 mm) Stainless steel coil casing Turbulators Access section (Pos #3) Access/blank/turning section Door- left side Marine LED light Fan section (Pos #4) Fan section Supply fan Door- right side 15in. diameter AF, class 1 Front-bottom discharge Left side drive NEMA premium compliant ODP Voltage /3 7.5 hp 1800 RPM Inverter balance with SGR Marine Light Field provided VFD starter and disconnect Gas heat (Pos #5) Gas heat module Front-top discharge Left hand door Gas supply left hand Voltage 200/60/3 Drum and tube - indirect 360 MBH output 10:1 Burner turndown ratio with Modulating control Stainless steel heat exchanger Natural gas Equipment Submittal Page 4 of 31

41 U of A Paty Hall FCU Replacements March 08, 2013 Performance Data - Performance Climate Changer Tags OSA-4 Unit level options Position Length (in) Width (in) Rigging weight (lb) Installed weight (lb) Roof curb weight (lb) Actual airflow (cfm) 6200 Shipping split 1 weight (lb) Shipping split 2 weight (lb) Fan section Position #4 Section length (in) Section weight (lb) Fan airflow (cfm) 6200 Overall ESP (in H2O) Total static pressure (in H2O) Fan pressure drop (in H2O) Fan outlet velocity (ft/min) 3020 Speed (rpm) 2291 Total brake horsepower (hp) Unit static efficiency (%) Outlet area (sq ft) 2.05 Motor hertz (Hz) 60 Access section Position #3 Section length (in) Section weight (lb) Coil section Position #2 Section length (in) Section weight (lb) Coil performance airflow (cfm) 6200 Unit airflow (cfm) 6200 Coil face area (sq ft) Coil face velocity (ft/min) 454 Air pressure drop (in H2O) Coil section pressure drop (in H2O) Coil rigging weight (lb) Coil installed weight (lb) Top or single coil dry weight (lb) Leaving dry bulb (F) Leaving wet bulb (F) Entering dry bulb (F) Entering wet bulb (F) Fluid type Propylene glycol Coil fluid percentage (%) Entering fluid temperature (F) Leaving fluid temperature (F) Fluid temperature rise (F) Standard fluid flow rate (gpm) Fluid pressure drop (ft H2O) Fluid velocity (ft/s) 3.35 Equipment Submittal Page 5 of 31

42 U of A Paty Hall FCU Replacements March 08, 2013 Tags OSA-4 Fluid volume (gal) Sensible capacity (MBh) Total capacity (MBh) Air mixing section Position #1 Section length (in) Section weight (lb) Opening 1 back - airflow (cfm) 6200 Opening 1 front - airflow (cfm) 6200 Opening 1 back - area (sq ft) 5.66 Opening 1 front - area (sq ft) Opening 1 back - face velocity (ft/min) 1096 Opening 1 back - pressure drop (in H2O) Opening 1 back total pressure drop (in H2O) Back hood pressure drop (in H2O) Back hood area (sq ft) Back inlet type Unducted Greatest entry PD (in H2O) Filter condition Mid-life Filter airflow (cfm) 6200 Filter area (sq ft) Filter face velocity (ft/min) 343 Filter pressure drop (in H2O) Total mixing section pressure drop (in H2O) Back total pressure drop (in H2O) Gas heat Position #5 Section length (in) Section weight (lb) Gas heat performance airflow (cfm) 6200 Entering dry bulb (F) Leaving dry bulb (F) Input capacity (MBh) Output capacity (MBh) Gas heat component PD (in H2O) Air temperature rise (F) Equipment Submittal Page 6 of 31

43 U of A Paty Hall FCU Replacements March 08, 2013 Mechanical Specifications - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 GENERAL Lifting Instructions The air handling units must be rigged, lifted, and installed in strict accordance with the Installation, Operation, and Maintenance manual (CLCH-SVX07B-EN). The units are also to be installed in strict accordance with the specifications. Units may be shipped fully assembled or disassembled to the minimum functional section size in accordance with shipping and job site requirements. Outdoor units shall be shipped on 6" integral base frame for the purpose of mounting units on a roof curb or field-supplied pier support system. Refer to the Product Data section for type of the base frame provided (for roof curb or pier-mount). All units will be shipped with an integral base frame designed with the necessary number of lift points for safe installation. All lifting lugs are to be utilized during lift. The lift points will be designed to accept standard rigging devices and be removable after installation. Units shipped in sections will have a minimum of four points of lift. Outdoor air handling units will be shipped with all openings covered to protect unit interior from in-transit debris. Installing contractor is responsible for long term storage in accordance with the Installation, Operation, and Maintenance manual (CLCH-SVX07B-EN). Unit shall be UL and C-UL Listed. Air-handling performance data shall be certified in accordance with AHRI Standard 430. Unit sound performance data shall be provided using AHRI Standard 260 test methods and reported as sound power. Trane, in providing this program and data, does not certify or warrant NC levels. These levels are affected by factors specific to each application and/or installation and therefore unable to be predicted or certified by Trane. Coil performance shall be certified in accordance with AHRI Standard 410. Unit Construction Unit constructed for outdoor installation. All unit panels shall be 2" solid, double-wall construction to facilitate cleaning of unit interior. Unit panels shall be provided with a mid-span, no-through-metal, internal thermal break. Casing thermal performance shall be such that under 55 F supply air temperature and design conditions on the exterior of the unit of 81 F dry bulb and 73 F wet bulb, condensation shall not form on the casing exterior. All outdoor AHU interior casing panels will be made of galvanized steel. Unit Paint External surface of unit casing will be coated with water-based polyurethane paint. Color to be standard "Slate Gray". Factory-painted units will be able to withstand a salt spray test in accordance with ASTM B117 for a minimum of 500 consecutive hours and shall meet the following requirements following the salt-spray test: - Mean scribe creepage rating of at least 6 per ASTM D1654 procedure A - Blister size no larger than #6 per ASTM D714 - Blister density no greater than Medium per ASTM D714 - No onset of red rust Casing Deflection The casing shall not exceed inch deflection per inch of panel span at 1.5 times design static pressure up to a maximum of +8 inches w.g. in all positive pressure sections and -8 inches w.g. in all negative pressure sections. The unit floor shall be of sufficient strength to support a 300-lb load during maintenance activities and shall deflect no more than inch per inch of panel span. Insulation Panel insulation shall provide a minimum thermal resistance (R) value of 13 ft²-h-ºf/btu throughout the entire unit. Insulation shall completely fill the panel cavities in all directions so that no voids exist and settling of insulation is Equipment Submittal Page 7 of 31

44 U of A Paty Hall FCU Replacements March 08, 2013 prevented. Panel insulation shall comply with NFPA 90A. Drain Pan All cooling coil sections shall be provided with an insulated, double-wall, stainless steel drain pan. To address indoor air quality (IAQ), the drain pan shall be designed in accordance with ASHRAE 62.1 being of sufficient size to collect all condensation produced from the coil and sloped in two planes promoting positive drainage to eliminate stagnant water conditions. The outlet shall be located at the lowest point of the pan and shall be sufficient diameter to preclude drain pan overflow under any normally expected operating condition. All drain pan threaded connections shall be visible external to the unit. Drain connections shall be of the same material as the primary drain pan and shall extend a minimum of 2-1/2" beyond the base to ensure adequate room for field piping of condensate drain traps. Refer to Product Data for specific information on which sections are supplied with a drain pan, the drain pan material and connection location. Access Door Construction Access doors shall be 2" double-wall construction. Interior and exterior door panels shall be of the same construction as the interior and exterior wall panels, respectively. All doors shall be provided with a thermal break construction of door panel and door frame. Gasketing shall be provided around the full perimeter of the doors to prevent air leakage. Surface-mounted handles shall be provided to allow quick access to the interior of the functional section and to prevent through-cabinet penetrations that could likely weaken the casing leakage and thermal performance. Handle hardware shall be designed to prevent unintended closure. Access doors shall be hinged and removable for quick, easy access. Hinges shall be interchangeable with the door handle hardware to allow for alternating door swing in the field to minimize access interference due to unforeseen job site obstructions. Door handle hardware shall be adjustable and visually indicate locking position of door latch external to the section. All doors shall be a minimum of 60" high when sufficient height is available, or the maximum height allowed by the unit height. Door handles shall be provided for each latching point of the door necessary to maintain the specified air leakage integrity of the unit. Optionally for indoor AHUs and as standard on outdoor AHUs, outward swing doors are provided with a single handle linked to multiple latching points. Refer to Product Data for specific information on which sections are supplied with an access door, the door location, a single handle, and a window. Factory-supplied Curb Outdoor AHU will be provided with a factory-supplied roof curb. Curb will be shipped to jobsite disassembled. Contractor will be responsible for assembly and mounting to roof structure per the Roof Curb Manual. Units with factory-supplied external piping cabinet(s), the factory-supplied curb will include a curb section for the pipe cabinet(s). Refer to the Roof Curb Detail drawing and Product Data section of submittal for height of factory-supplied roof curb(s). Marine Light A factory-mounted, weather resistant (enclosed and gasketed to prevent water and dust intrusion), light emitting diode (LED) fixture shall be provided in sections of the unit as specified for maintenance and service visibility. Fixture shall be complete with aluminum die cast housing, polycarbonate lens designed for maximum light output, and LEDs wired to a single switch within a factory provided service module. LED lighting shall provide instant-on "white" light and have a minimum 50,000 hour life. Fixtures shall be designed for flexible positioning during maintenance and service activities for optimal location. All lights within the unit shall be wired to a single switch within the factory provided service module. The service module shall include a GFCI receptacle separate from the load side of the equipment. Electrical contractor shall be required to provide a 120V supply to the factory-mounted service module for the marine light circuit (unless single-point power is provided) and for the GFCI receptacle circuit per NEC. Service module shall be provided on the fan section, unless a Control Section is provided. In which case, the service module will be provided on the Control Section. Refer to the Product Data section of the submittal for sections with marine lights. MIXING SECTION A mixing section shall be provided to support the damper assembly for outdoor, return, and/or exhaust air. Inlet Hoods Inlet hoods are provided on the outside air openings and equipped with high performance moisture eliminators to minimize water carryover from the outside into the unit casing. Eliminators also perform the function of a bird screen to prevent nesting. Refer to the unit As-Built and Product Data section for specific information on which sections are supplied with inlet hood. Equipment Submittal Page 8 of 31

45 U of A Paty Hall FCU Replacements March 08, 2013 Dampers Dampers shall modulate the volume of outdoor, return, or exhaust air. The dampers shall be of double-skin airfoil design with metal, compressible jamb seals and extruded-vinyl blade-edge seals on all blades. The blades shall rotate on stainless-steel sleeve bearings. The dampers shall be rated for a maximum leakage rate of 4 cfm/ft² at 1 in. w.g. complying with ASHRAE 90.1 maximum damper leakage. All leakage testing and pressure ratings shall be based on AMCA Standard 500-D. Dampers may be arranged in a parallel or opposed-blade configuration. Filters Mixing sections shall be provided with a filter rack as indicated in the Product Data and As-Built sections of the submittal. 4-inch pleated media filters made with 100% synthetic fibers that are continuously laminated to a supported steel-wire grid with water repellent adhesive shall be provided. Filters shall be capable of operating up to 625 fpm face velocity without loss of filter efficiency and holding capacity. The filters shall have a MERV 8 rating when tested in accordance with the ANSI/ASHRAE Standard COIL SECTION The coil section shall be provided complete with coil and coil holding frame. The coils shall be installed such that headers and return bends are enclosed by unit casings. If two or more cooling coils are stacked in the unit, an intermediate drain pan shall be installed between each coil and be of the same material as the primary drain pan. Like the primary drain pan, the intermediate drain pan shall be designed being of sufficient size to collect all condensation produced from the coil and sloped to promote positive drainage to eliminate stagnant water conditions. The intermediate pan shall begin at the leading face of the water-producing device and be of sufficient length extending downstream to prevent condensate from passing through the air stream of the lower coil. Intermediate drain pan shall include downspouts to direct condensate to the primary drain pan. The outlet shall be located at the lowest point of the pan and shall be sufficient diameter to preclude drain pan overflow under any normally expected operating condition. Water Coils (UW, UU, UA, W, 5W, 5A, WD, 5D, D1, D2, P, or TT) The coils shall have aluminum fins and seamless copper tubes. The coil casing will be stainless steel. Refer to the Product Data section of the submittal for the coil casing material. The coils shall be proof-tested to 300 psig and leak-tested under water to 200 psig. Coil performance data and coils containing water or ethylene glycol shall be certified in accordance with AHRI Standard 410. Propylene glycol and calcium chloride, or mixtures thereof, are outside the scope of AHRI Standard 410 and, therefore, do not require AHRI 410 rating or certification. Coil header connections are constructed of cast iron with female connections, steel block with female connections or steel pipe with male connections. Tubes are 1/2" [13mm] OD 0.016" [0.406mm] thick copper. ACCESS/INSPECTION / TURNING SECTION A section shall be provided to allow additional access/inspection of unit components and space for field-installed components as needed. An access door shall be provided for easy access. All access sections shall be complete with a double-wall, removable door downstream for inspection, cleaning, and maintenance. Interior and exterior door panels shall be of the same construction as the interior and exterior wall panels, respectively. All doors downstream of cooling coils shall be provided with a thermal break construction of door panel and door frame. AF FAN SECTION The fan type shall be provided as required for stable operation and optimum energy efficiency. The fan shall be a double-width, double-inlet, multiblade-type, airfoil (AF) fan. The fan shall be equipped with self-aligning, antifriction bearings with an L-50 life of 200,000 hours, as calculated per ANSI/AFBMA Standard 9. For any bearing requiring relubrication, the grease line shall be extended to the fan support bracket on the drive side. The fan shall be statically and dynamically balanced at the factory as a complete fan assembly (fan wheel, motor, drive, and belts). The fan shaft shall not exceed 75 percent of its first critical speed at any cataloged speed. Fan wheels shall be keyed to the fan shaft to prevent slipping. The fan shafts shall be solid steel. The fan section shall be provided with an access door on the drive side of the fan. Fan performance shall be certified as complying with AHRI Standard 430. Motor Frame The motor shall be mounted integral to the isolated fan assembly and furnished by the unit manufacturer. The motor is mounted inside the unit casing on an adjustable base to permit adjustment of drive belt tension (not applicable for direct drive plenum fans). The motor shall meet or exceed all NEMA Standards Publication MG 1 requirements and comply with NEMA Premium efficiency levels when applicable except for fractional horsepower motors which are not covered by the NEMA classification. The motor shall be T-frame, squirrel cage with size, type, and electrical characteristics as Equipment Submittal Page 9 of 31

46 U of A Paty Hall FCU Replacements March 08, 2013 shown on the equipment schedule. Refer to the Product Data section for selected fan motors within each unit. Two-Inch Spring Isolators The fan and motor assembly (on sizes 10 to 120) shall be internally isolated from the unit casing with 2-inch (50.8 mm) deflection spring isolators, furnished and installed by the unit manufacturer. The isolation system shall be designed to resist loads produced by external forces, such as earthquakes, and conform to the current IBC seismic requirements. Drive Service Factor The drives shall be constant speed with fixed-pitch sheaves. The drives shall be selected at a minimum 50 percent larger than the motor brake horsepower (1.5 service factor). GAS HEAT SECTION Indirect-fired gas heaters shall be completely factory assembled, piped, and operationally fire tested at the factory prior to shipment. The heat exchanger primary drum and secondary tubes shall constructed from 14-gauge, 409 stainless steel. The industrial / commercial burner shall be UL listed, forced draft, and fully modulating. The control panel shall be equipped with Honeywell RM7800 flame management controls and appropriate safeties. The gas heat section construction shall match the rest of the air handling unit and be an integral part of the unit. All burner and control components shall be housed in a burner vestibule with a large access door. The entire section shall bear a UL or CUL label for Commercial-Industrial Gas Heating Equipment (ANSI / UL Standard 795) and Industrial Gas-Fired Package Furnaces (CGA Standard ). Features: - Natural gas burner - 200V 3-phase power - 10:1 full-modulating nominal turndown - UL / Factory Mutual insurance-rated gas train Field connections: in. w.c. gas pressure in appropriate volume VAC or 3-phase power (voltage requirements depend on size) - Start / stop dry contact - Modulating 0-10 VDC control signal - Condensate drain - Hardwired supply fan interlocks are recommended - Flue stack (factory supplied, field installed for outdoor units) Equipment Submittal Page 10 of 31

47 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Equipment Submittal Page 11 of 31

48 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 5 S2 4 3 S1 2 1 Pos # Module Air mixing section Coil section Access section Fan section Gas heat Roof Curb Length /8 42 5/8 61 1/8 Weight Installed Unit Weight lbs 28" / /4 6 Overall Elevation View: Right - Shipping splits indicated by bold outline. - Measurements in inches For maneuvering purposes, include inches to each ship split length for overlapping panel flange. Flange will not add to overall installed unit length sho Basic Overall Plan View: Top - Measurements in inches OPENING AND DIMENSIONS MAY VARY FROM CONTRACT DOCUMENTS / RETURN OF APPROVED DRAWINGS CONSTITUTES ACCEPTANCE OF THESE VARIANCES / NOT TO SCALE Unit size: 14 Unit Casing: 2in Double Wall Product group: Outdoor unit Proposal Number: Integral base frame: 6in. integral base frame Paint: Factory painted - slate gray Job Name: Actual airflow: 6200 cfm Sales Office: Rigging/Installed Weight: lb/ lb Performance Climate Changer Air Handlers Equipment Submittal Page 12 of 31

49 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA /8 Right Side of Unit 42 5/8 14 1/ Detailed Plan View: Top - Measurements in inches 2 5/ / " dia elec. conn.(nema) 61 1/8 Left Side of Unit 10 3/4 5 5/8 6 1/4 14 1/ /8 Detailed Plan View: Bottom - Measurements in inches OPENING AND DIMENSIONS MAY VARY FROM CONTRACT DOCUMENTS / RETURN OF APPROVED DRAWINGS CONSTITUTES ACCEPTANCE OF THESE VARIANCES / NOT TO SCALE Unit size: 14 Unit Casing: 2in Double Wall Product group: Outdoor unit Proposal Number: Integral base frame: 6in. integral base frame Paint: Factory painted - slate gray Job Name: Actual airflow: 6200 cfm Sales Office: Rigging/Installed Weight: lb/ lb Performance Climate Changer Air Handlers Equipment Submittal Page 13 of 31

50 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA / / / / /4 47 3/4 1" N.P.T.E 14 1/8 12 3/ /4 Detailed Elevation View: Right - Measurements in inches /8 31" 10" 17" 7 3/4 8 28" 28 1/2 19 1/8 2 7/ / /8 25 5/8 42 5/8 10 3/ /4 46 1/2 8 6 Detailed Elevation View: Left - Measurements in inches 44 1/2 61 1/8 OPENING AND DIMENSIONS MAY VARY FROM CONTRACT DOCUMENTS / RETURN OF APPROVED DRAWINGS CONSTITUTES ACCEPTANCE OF THESE VARIANCES / NOT TO SCALE Unit size: 14 Unit Casing: 2in Double Wall Product group: Outdoor unit Proposal Number: Integral base frame: 6in. integral base frame Paint: Factory painted - slate gray Job Name: Actual airflow: 6200 cfm Sales Office: Rigging/Installed Weight: lb/ lb Performance Climate Changer Air Handlers Equipment Submittal Page 14 of 31

51 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 1 1/2 2 3/4 1 1/ / /4 33 1/4 47 3/ / / Detailed Elevation View: Front - Measurements in inches 28 1/2 12 3/ Detailed Elevation View: Back - Measurements in inches OPENING AND DIMENSIONS MAY VARY FROM CONTRACT DOCUMENTS / RETURN OF APPROVED DRAWINGS CONSTITUTES ACCEPTANCE OF THESE VARIANCES / NOT TO SCALE Unit size: 14 Unit Casing: 2in Double Wall Product group: Outdoor unit Proposal Number: Integral base frame: 6in. integral base frame Paint: Factory painted - slate gray Job Name: Actual airflow: 6200 cfm Sales Office: Rigging/Installed Weight: lb/ lb Performance Climate Changer Air Handlers Equipment Submittal Page 15 of 31

52 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Equipment Submittal Page 16 of 31

53 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Equipment Submittal Page 17 of 31

54 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA / / /4 Detailed Plan View: Curb - Measurements in inches OPENING AND DIMENSIONS MAY VARY FROM CONTRACT DOCUMENTS / RETURN OF APPROVED DRAWINGS CONSTITUTES ACCEPTANCE OF THESE VARIANCES / NOT TO SCALE Unit size: 14 Unit Casing: 2in Double Wall Product group: Outdoor unit Proposal Number: Integral base frame: 6in. integral base frame Paint: Factory painted - slate gray Job Name: Actual airflow: 6200 cfm Sales Office: Rigging/Installed Weight: lb/ lb Performance Climate Changer Air Handlers Equipment Submittal Page 18 of 31

55 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Equipment Submittal Page 19 of 31

56 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Equipment Submittal Page 20 of 31

57 U of A Paty Hall FCU Replacements March 08, 2013 As-Built - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Equipment Submittal Page 21 of 31

58 U of A Paty Hall FCU Replacements March 08, 2013 Fan Curve - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 T o t a l S t a t i c P r e s s u r e ( i n H 2 O ) RPM 1800 RPM 1600 RPM 1400 RPM 2800 RPM 2600 RPM 2400 RPM 2200 RPM 2900 RPM Supply Size 14 Horizontal Draw-Thru 15 inch AF Class 1 - Single Fan %WO 50 %WO 60 %WO BHP adjusted 5% for approximate drive loss UnitSize: 15AA Motor Frequency: 60.00Hz Operating Airflow: cfm Operating Static Pressure: 3.57 in H2O Operating RPM: Operating Brake Power: 6.44 hp Altitude: 0.00 ft Design Temp: F Max BHP: 6.82 hp 70 %WO Efficiency: % Date: 3/8/13 Datafile: C:\Program Files\Trane Company\TOPSS\CSAA\Csaa_fans.ran 80 %WO 90 %WO h p h p h p h p h p h p h p Airflow (cfm) Equipment Submittal Page 22 of 31

59 U of A Paty Hall FCU Replacements March 08, 2013 Accessory - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Filter mixing box Coil Fan VFD UV Lights or TCAC C B A Gas heat E D Clearance items 3 4 Access door F TALL Note: At a minimum, the below clearance dimensions are recommended on one side of the unit for regular service and maintenance. Refer to as-built submittal for locations of items such as filter access doors, coil, piping connections, motor locations, etc. Sufficient clearance must be provided on all sides of unit for removal of panels or section-to-section attachment. Clearance for starters, VFDs, or other high-voltage devices must be provided per NEC requirements TALL TALL TALL TALL 50 TALL TALL A (filter, gas heat) B (coil, humidifier) C (UV Lights) C (TCAC) D (External Starter or VFD - shown) D (Internal Starter or VFD) E (fan) F (Gas Heat Ext Vestible) N/A N/A N/A 115 N/A 118 N/A 136 N/A 140 N/A 156 N/A 156 N/A N/A Int Vestible) F (Gas Heat N/A N/A N/A 92 N/A 106 N/A 112 N/A 125 N/A 138 N/A 138 N/A Equipment Submittal Page 23 of 31

60 U of A Paty Hall FCU Replacements March 08, 2013 Accessory - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 ALLOW FOR EXHAUST AIR DISCHARGE MINIMUM COIL PULL CLEARANCE 87" (2210 mm) SIDE INLET OR EXHAUST HOOD CLEARANCE A ALLOW FOR HORIZONTAL DISCHARGE MAX ROOF OPENING = UNIT LENGTH AND WIDTH MINUS 5" (127mm) BACK INLET OR EXHAUST HOOD CLEARANCE A ALLOW FOR EXHAUST AIR DISCHARGE A 22 3/8" (568 mm) 22 1/4" (565 mm) 22 1/8" (562 mm) 20 3/8" (518 mm) 22 1/8" (562 mm) Side economizer inlet Side economizer exhaust Side mixing box inlet/exhaust Back mixing box inlet Back exhaust damper SIDE INLET OR EXHAUST HOOD CLEARANCE A ALLOW FOR EXHAUST AIR DISCHARGE Equipment Submittal Page 24 of 31

61 U of A Paty Hall FCU Replacements March 08, 2013 Accessory - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 Recommendation for Roof Curb Installation Refer to Performance IOM for specific installation instructions 2 x 4 NAILER ROOF CURB GASKET NAIL (See Note 1) COUNTER FLASHING (See Note 1) FLASHING (See Note 1) ROOFING/INSULATING MATERIAL (See Note 1) 4 x 4 CANT (See Note 1) ROOF INSULATION (See Note 1) ROOF CURB COUNTER FLASHING (See Note 2) FLASHING (See Note 2) 2 x 4 NAILER ROOF CURB WOODEN NAILER (See Note 1) GASKET NAIL (See Note 1) COUNTER FLASHING (See Note 1) ROOFING/INSULATING MATERIAL (See Note 1) FLASHING (See Note 1) 4 x 4 CANT (See Note 1) ROOF INSULATION (See Note 1) ROOF PURLIN ROOF DECK ROOF PURLIN ROOF DECK Recommendation for Pier Mounting Refer to Performance IOM for specific installation instructions Note: 1. Materials to attach roof curb to roof are to be supplied by the installer. 2. Flashing or counter flashing should not come to or over top of curb. 3. Roof curb must be mechanically fastened to roof surface. 4'-0" TYP Note: PIERS 1. Pier supports should be inside 3" (3-50) or 4" (57-120) flat of unit base. Unit cannot be supported by unit base drip leg. 2. Pier supports should be no wider than 2 3/4", due to supports perpendicular to airflow. 3. Piers beneath shipping splits must be structurally sound to support the weight of the unit. Equipment Submittal Page 25 of 31

62 U of A Paty Hall FCU Replacements March 08, 2013 Accessory - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 RELATIONSHIP OF CURB TO UNIT AS-BUILT OPENING IN BOTTOM OF UNIT OPENING IN BOTTOM OF UNIT 6" 6" 6" RECTANGULAR OPENINGS 1" 1" 6" E F F E 1/2" SECTION A-A SECTION B-B / SECTION C-C 1/2" SUPPLY FAN OR DISCHARGE PLENUM (SEE NOTE 1) MIX BOX, RETURN FAN OR EXHAUST FAN SECTION (SEE NOTE 1) OPENING IN BOTTOM OF UNIT OPENING IN BOTTOM OF UNIT 6" ROUND OPENINGS 6" E F F E 1/2" SECTION A-A SECTION B-B / SECTION C-C 1/2" SUPPLY FAN OR DISCHARGE PLENUM (SEE NOTE 1) MIX BOX, RETURN FAN OR EXHAUST FAN SECTION (SEE NOTE 1) OPENING IN BOTTOM OF UNIT OPENING IN BOTTOM OF UNIT 6" 1" BELLMOUTH OPENINGS 1" 6" E F F E 1/2" SECTION A-A SECTION B-B / SECTION C-C 1/2" SUPPLY FAN OR DISCHARGE PLENUM (SEE NOTE 1) MIX BOX, RETURN FAN OR EXHAUST FAN SECTION (SEE NOTE 1) B B NOTE: 1. E and F are representative of dimensions on the accessory as-built used to locate opening(s) in the roof surface. A A C C A A Equipment Submittal Page 26 of 31

63 U of A Paty Hall FCU Replacements March 08, 2013 Accessory - Performance Climate Changer Item: A1 Qty: 1 Tag(s): OSA-4 6" Equipment Submittal Page 27 of 31

64 U of A Paty Hall FCU Replacements March 08, 2013 Accessory - Performance Climate Changer Trap Schedule Item: A1 Qty: 1 Tag(s): OSA-4 L H J Drain pan trapping for section under negative pressure L = H + J + pipe diameter where: H = 1 inch for each inch of negative pressure (loaded filters) plus 1 inch J = 1 2 H Drain pan trapping for section under positive pressure L = H + J + pipe diameter where: H = 1/2 inch (minimum) J = 1 2 inch plus the unit positive static pressure at coil discharge (loaded filters) Unit Tag(s) Unit Size Entering Ext. Static Pressure (in H2O) Discharge Ext. Static Pressure (in H2O) OSA-4 2 Unit size Drain pan Section Location Coil section [2] Recommended Trap Dimensions 1 H (in) J (in) L (in) Selected Baserail Height (in) Trap height and selected baserail heights should be reviewed to determine appropriate housekeeping pad height. 2 The external static pressure used for fan selection was assumed to be divided 50% to entering duct external static pressure and 50% discharge external static pressure. Equipment Submittal Page 28 of 31

65 U of A Paty Hall FCU Replacements March 08, 2013 Accessory - Performance Climate Changer Filter Schedule Item: A1 Qty: 1 Tag(s): OSA-4 Unit Tag(s) Unit Size OSA-4 Unit size 14 Filter Location Air mixing section [1] Filter Arrangement Filter Depth - 4in. filter frame Filter Type Pleated media - run set MERV Rating MERV 8 Filter Quantity 4 2 Filter Size 20in.x20in. 20in.x25in. Equipment Submittal Page 29 of 31

66 U of A Paty Hall FCU Replacements March 08, 2013 Field Wiring - Performance Climate Changer MCA MOP Schedule Item: A1 Qty: 1 Tag(s): OSA-4 Unit Tag(s) Circuit Circuit Description Voltage/Phase/Hz MCA (A) MOP (A) 1 Supply fan motor(s) /3/ OSA-4 2 Gas heat /3/ Lights + switch 115/1/ Receptacle 115/1/ Equipment Submittal Page 30 of 31

67 U of A Paty Hall FCU Replacements March 08, 2013 Field Installed Options - Part/Order Number Summary This is a report to help you locate field installed options that arrive at the jobsite. This report provides part or order numbers for each field installed option, and references it to a specific product tag. It is NOT intended as a bill of material for the job. Product Family - Performance Climate Changer Item Tag(s) Qty Description Model Number A1 OSA-4 1 Performance Climate Changer ( CSAA ) CSAA014UB Field Installed Option Description Pleated media - run set Part/Ordering Number Equipment Submittal Page 31 of 31

68 Submittal Prepared For: Whitaker & Rawson Inc 3332 Old Montgomery Highway Homewood, AL Sold To: University of Alabama Date: March 07, 2013 Customer P.O. Number: Customer Project Number: Job Number: Job Name: U of A Paty Hall FCU Replacements Trane U.S. Inc. dba Trane is pleased to provide the enclosed submittal for your review and approval. Product Summary Qty Product 310 Fan Coil Air Conditioning Units The attached information describes the equipment we propose to furnish for this project, and is submitted for your approval. Chandler McGarrah Trane 1030 London Drive, Suite 100 Birmingham, AL Phone: (205) Fax: (205) J:\JOBS\50\81408\10\U of A Paty Hall FCU Replacement Submittal Final.doc

69 Table Of Contents Product Summary... 1 Fan Coil Air Conditioning Units (Items A1 - A6)... 4 Tag Data... 4 Product Data... 4 Performance Data... 6 Mechanical Specifications... 7 Unit Dimensions Accessory Field Wiring Field Installed Options - Part/Order Number Summary Fan Coil Air Conditioning Units... 29

70 U of A Paty Hall FCU Replacements March 07, 2013 Fan Coil Unit Specification Items: Unit Level Horizontal Units with Exposed Cabinet Horizontal Units to have Metal Bar Grille Outlet Vertical Flat Top Units with Exposed Cabinet Vertical Units to have Metal Bar Grille Outlet and Standard Toe Space Inlet w/o Grille Units to Have Closed Cell Insulation FCU1-1~282 to be size 040 and meet scheduled performance data listed below FCU2-1~15 and FCU2-15 to be size 040 and meet scheduled performance data listed below FCU3-1~12 to be size 060 and meet scheduled performance data listed below FCU4-12 to be size 0100 and meet scheduled performance data listed below Fans to have factory tested and programmed ECM motors 1 MERV 8 Filter Cooling/Heating coil configured for 2 Pipe System Operation Cooling/Heating coil must included water temp sensor and control logic for auto changeover IAQ Drain Pan Coil Piping Package to include 3 Way, 2 Position Control Valve, Supply Isolation Valves, Manual Circuit Setter/Shutoff Valve in Return Line, P/T Ports on Both Supply and Return Lines, Union Piping Connections, Balance Cock in Bypass Line Coil Piping Package to be Factory Assembled, Tested and Installed Controls for Standalone Operation Wall mounted zone temperature sensor with Off/Auto/Low/Medium/High fan speed switch Unit Disconnect Condensate Overflow Detection Factory Wired to Shutdown Fan and Control Valve Shipping - FOB Jobsite See Mechanical Specification Section (pages 6-7) for the Remainder of the Applicable Fan Coil Unit Specifications. Equipment Submittal Page 3 of 29

71 U of A Paty Hall FCU Replacements March 07, 2013 Tag Data - Fan Coil Air Conditioning Units (Qty: 310) Item Tag(s) Qty Description Model Number A1 FCU1-1~ Fan Coil Air Conditioners (UniTrane) FCDB040 A2 FCU2-1~14 14 Fan Coil Air Conditioners (UniTrane) FCBB040 A3 FCU Fan Coil Air Conditioners (UniTrane) FCBB040 A4 FCU3-1~11 11 Fan Coil Air Conditioners (UniTrane) FCBB060 A5 FCU Fan Coil Air Conditioners (UniTrane) FCBB060 A6 FCU4-1 1 Fan Coil Air Conditioners (UniTrane) FCBB100 Product Data - Fan Coil Air Conditioning Units All Units Fan Coil 115v/60hz/1ph Color to be selected from Trane Standard Colors by the Architect Free discharge fan motor 3 row cooling/heating coil IAQ Drain Pan Manual air vent With disconnect switch 1" MERV 8 filter Factory Installed Ball Valve package (supply) & Manual circuit setter return, P/T supply/return ports, Unions pipe connections, and balance fitting in bypass line. Tracer ZN 010 Wall mounted temperature sensor (set point, OALMH) (Fld) Condensate overflow detection Item: A1 Qty: 282 Tag(s): FCU1-1~282 Horizontal cabinet Size 040 With piping, left hand connection Bottom stamped louver return Front bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A2 Qty: 14 Tag(s): FCU2-1~14 Vertical cabinet Size 040 With piping, right hand connection Toe space return inlet without grille Top bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A3 Qty: 1 Tag(s): FCU2-15 Vertical cabinet Size 040 With piping, left hand connection Toe space return inlet without grille Top bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A4 Qty: 11 Tag(s): FCU3-1~11 Vertical cabinet Size 060 With piping, right hand connection Toe space return inlet without grille Top bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A5 Qty: 1 Tag(s): FCU3-12 Vertical cabinet Size 060 With piping, left hand connection Equipment Submittal Page 4 of 29

72 U of A Paty Hall FCU Replacements March 07, 2013 Toe space return inlet without grille Top bar grille supply 3 way, 2 position, normally closed (28 psig) cooling control valve Item: A6 Qty: 1 Tag(s): FCU4-1 Vertical cabinet Size 100 With piping, right hand connection Front bar grille return Top bar grille supply 3 way, 2 position, normally closed (20 psig) cooling control valve Equipment Submittal Page 5 of 29

73 U of A Paty Hall FCU Replacements March 07, 2013 Performance Data - Fan Coil Air Conditioning Units Tags FCU1-1~282, FCU2-1~15 FCU3-1~12 FCU4-1 Design airflow (cfm) Total cooling capacity (MBh) Sensible capacity (MBh) Cooling EDB (F) Cooling EWB (F) Cooling LDB (F) Cooling LWB (F) Cooling ent fluid temp (F) Cooling lvg fluid temp (F) Cooling delta T (F) Cooling flow rate (gpm) Cooling fluid PD (ft H2O) Fluid type Water Water Water Water Total heating capacity (MBh) Heating EAT (F) Heating LAT (F) Heating ent fluid temp (F) Heating lvg fluid temp (F) Heating delta T (F) Heating flow rate (gpm) Heating fluid PD (ft H2O) ESP (in H2O) Motor power (W) Motor speed High High High High Motor rpm #1 (rpm) Motor rpm #2 (rpm) Motor hp #1 (hp) Motor hp #2 (hp) Min circuit ampacity (A) Max fuse size (A) Unit length (in) Unit width (in) Unit height (in) Shipping weight (lb) Operating weight (lb) Equipment Submittal Page 6 of 29

74 U of A Paty Hall FCU Replacements March 07, 2013 Mechanical Specifications - Fan Coil Air Conditioning Units Item: A1 - A6 Qty: 310 Tag(s): FCU1-1~282, FCU2-1~15, FCU3-1~12, FCU4-1 Performance Data Capacity: Unit capacities are certified under the Industry Room Fan Coil Air Conditioner Certification Program in accordance with AHRI standard Safety: All standard units are UL and CUL approved. Vertical Cabinet Basic Construction The basic unit includes a chassis, coil(s), fan wheel(s), fan casing(s), fan board, and motor. Units also include a positively sloped (multi-plane), IAQ main drain pan with closed cell insulation. Units with standard piping package also include a thermoplastic auxiliary drain pan. The fan board assembly and drain pans are removable. The fan board assembly includes a quick disconnect motor plug. The chassis is the structural frame constructed of 18 ga. galvanized steel. The unit is acoustically and thermally insulated with closed cell insulation. The front panel is fabricated from 16 ga. galvanized steel. All other panels are fabricated from 18 ga. galvanized steel. All cabinets are made rigid by channel forming. Side panels are removable for piping access. Discharge grilles are recessed to resist condensate formation. The hinged access door is flush with the unit. Horizontal Cabinet Basic Construction The basic unit includes a chassis, coil(s), fan wheel(s), fan casing(s), fan board and motor(s). Units also include a positively sloped (multi-plane), non-corrosive main drain pan with closed cell insulation. A thermoplastic auxiliary drain pan is included on fan coils with standard piping packages. The fan board assembly and both drain pans are removable. The fan board assembly includes a quick disconnect motor plug. The chassis is the structural frame constructed of 18 ga. galvanized steel. The unit is acoustically and thermally insulated with closed cell insulation. The bottom panel is fabricated from 16 ga. galvanized steel. All other panels are fabricated from 18 ga. galvanized steel. All panels are made rigid by channel forming. Side panels are removable for piping access. The discharge grille is recessed to resist condensate formation. The hinged access door is flush with the unit. Unit Finish All cabinet parts are cleaned, bonderized, phosphatized and painted with one of six decorator colors. Standard finish meets ASTM B117 specifications (salt spray test). Fan The galvanized steel fan wheels are centrifugal forward-curved and double-width. Fan wheels and housings are corrosion resistant. Fan housings are constructed of formed sheet metal. Motor All motors are Brushless DC (BLDC)/Electronically Commutated Motors (ECM) factory programmed and run tested in assembled units. The motor controller is mounted in a touch-safe control box with a built in integrated user interface and LED tachometer. If adjustments are needs, motor parameters can be adjustments through momentary contact switches accessible without factory service personnel on the motor control board. Motors will soft ramp between speeds to lessen the acoustics due to sudden speed changes. Motors can be operated at three speeds or with a field supplied variable speed controller. The motor will choose the highest speed if there are simultaneous/conflicting speed request. All motors have integral thermal overload protection with a maximum ambient operating temperature of 104F and are permanently lubricated. Motors are capable of starting at 50% percent of rated voltage and operating at 90 percent of rated voltage on all speed settings. Motors can operate up to 10 percent over voltage. Coil All water coils are burst tested at 450 PSIG (air) and leak tested at 100 PSIG (air under water). Maximum main coil working pressure is 300 PSIG. Maximum entering water temperature is 200 degrees F (93 degrees C). Tubes and U-bends are 3/8" (10 mm) O.D. copper. Fins are aluminum and are mechanically bonded to the copper tubes. Coil connections are 5/8" (16 mm) O.D. copper tubing. Coil Air Vents - Manual Manual air vents are rated at 300 psig. Equipment Submittal Page 7 of 29

75 U of A Paty Hall FCU Replacements March 07, 2013 Piping Package - 2-Pipe Two-pipe, package is factory-tested and installed. All piping packages are burst tested at 450 PSIG (air) and leak tested at 100 PSIG (air under water). The interconnecting piping maximum working pressure is 300 PSIG. Deluxe Ball & Manual Circuit Setter The deluxe accessory piping package is provided. Piping accessories included in this package are unions on the supply and return lines. Any condensation from the piping package is designed to be collected by the auxiliary drain pan on fan coil units. A ball valve is mounted on the supply line and a balancing valve is mounted on the return line. The ball valve is a shut-off or stop type valve only with a maximum working pressure of 400 psig. The balancing valve is a manual circuit setter type and includes two P/Ts plugs. This valve doubles as a flow control device and a shut-off valve with a maximum working pressure of 175 psig. P/Ts will also be provided on supply side. Main Control Valve The piping package also includes a 3-way normally closed (spring-return) main control valve mounted in the return line(s) of the factory-installed piping package. The 3-way valve package includes a balancing fitting in the bypass with a maximum working pressure of 150 psig. The valve is rated for a maximum pressure differential of 28 psig across the valve, and the maximum working pressure of the valve is 300 psig. In a 2-pipe changeover system, the cooling control valve will act as the heating control valve also. Installation Note Unit leveling and drain line pitch: Set unit level by checking the casing. The Trane Company and the industry in general recommends a drain line pitch of 1" (25mm) drop per ten feet. WARNING: Tighten all unions when piping units. Factory tightens unions, but they may loosen during shipping. Wall-mounted Tracer ZN010 Zone Sensor A wall mounted ZN010 zone sensor (Off/Auto/High/Med/Low & Setpoint Dial) is provided with the fancoil unit. Also included is a 24 V control transformer that is factory mounted and wired in the control box. Wiring (by others) between the unit and wall thermostat module is 24 V. The unit requires only a single point power connection. Tracer ZN010 Control Features All ZN010 have the following control features: Automatic Heat/Cool Mode Determination, Occupied/Unoccupied Operation, Random Start and Manual Output Test Function All ZN010 include the following input/output abilities: Binary Inputs: Low temperature detection, Condensate Overflow, Occupancy Binary Outputs: Fan High, Medium, and/or Low, Cooling output, Heating output, Damper output Analog Inputs: Zone temperature, Setpoint temperature, Fan mode switch, Entering water temperature, Discharge air temperature Sequence of Operation with Valves When the ZN010's switch is in the off position, the fan is off; control valves. The AUTO selection is used for fan cycling. The fan cycles with control valves to maintain setpoint temperature. In cooling mode, the fan cycles from off to medium and in heating mode it cycles from off to low (configurable for heating and cooling). When no heating or cooling is required, the fan is off. When the thermostat setting is in the Low/Med/High selection the fan will run continuously while the control valves cycle to maintain setpoint temperature. Disconnect Switch A unit mounted, non-fused disconnect switch is available as a standard option on all units. 1" MERV 8 Filter The filter is concealed from sight and easily removable. A 1" MERV 8 filter is provided in the unit. The MERV 8 filters have a rating based on ASHRAE Standard The average dust spot efficiency is no less than 35 to 40 percent when tested in accordance with ASHRAE 52.1 atmospheric dust spot method. Equipment Submittal Page 8 of 29

76 U of A Paty Hall FCU Replacements March 07, 2013 Condensate Overflow Sensor This safety option de-energizes the system switch when the auxiliary drain pan is in danger of overflowing with condensate. This condition is indicated when the float switch rises to 50% of its travel, and the normally closed input latches open. The fan shuts off and any end devices (valves or actuators) go to their de-energized position. The float switch is provided at the auxiliary drain pan and factory-wired. Equipment Submittal Page 9 of 29

77 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A1 Qty: 282 Tag(s): FCU1-1~282 BACK OF UNIT 15 1/2" 13 3/4" MAIN RETURN CONN MAIN SUPPLY CONN MOUNTING FLANGE MOUNTING FLANGE TOP VIEW 2 1/2" PIPING CONNECTIONS ARE LOCATED WITHIN ENCLOSED AREA 2 5/8" 5" 4" BACK VIEW NOTES: 1. PIPING CONNECTIONS ARE 5/8" OUTSIDE DIAMETER COPPER. 2. LOCATING DIMENSIONS HAVE A PLUS OR MINUS 1" TOLERANCE. Equipment Submittal Page 10 of 29

78 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A1 Qty: 282 Tag(s): FCU1-1~ /16" 38 1/4" 24" ISO1 VIEW BACK VIEW (4) 5/8" HANGER HOLES 5 3/4" 10 3/8" NOTES: 23 3/4" 1. ARROW(S) INDICATE THE DIRECTION OF AIRFLOW. 2. FILTERS ARE ACCESSED THROUGH THE BOTTOM OF UNIT. 7 3/8" 3. CONTROL WIRES SHOULD ENTER CONTROL BOX THROUGH TOP FRONT KNOCKOUT. 4. POWER WIRES ARE TO ENTER CONTROL BOX THROUGH FRONT BOTTOM CONDUIT ENTRANCE KNOCKOUTS. 15 1/2" 5. PIPING CONNECTIONS ARE 5/8" OD COPPER. 6. AUXILIARY DRAINPAN CONN: MAIN: 7/8" OD TUBE & CLAMP SECONDARY: 3/8" ID TUBE 7. STANDARD ENDPOCKET WIDTH IS 7". 26 1/4" UNIT WEIGHT BOTTOM VIEW lb LEFT VIEW RIGHT VIEW Equipment Submittal Page 11 of 29

79 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A1 Qty: 282 Tag(s): FCU1-1~282 Equipment Submittal Page 12 of 29

80 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A2, A4, A6 Qty: 26 Tag(s): FCU2-1~14, FCU3-1~11, FCU /8" 2 7/8" MAIN SUPPLY CONN MAIN RETURN CONN MOUNTING FLANGE MOUNTING FLANGE 14 5/8" 15 3/8" FRONT VIEW NOTES: 1. PIPING CONNECTIONS ARE 5/8" OUTSIDE DIAMETER COPPER. 2. LOCATING DIMENSIONS HAVE A PLUS OR MINUS 1" TOLERANCE. Equipment Submittal Page 13 of 29

81 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A2 Qty: 14 Tag(s): FCU2-1~14 NOTES: 1. ARROW(S) INDICATE THE DIRECTION OF AIRFLOW. 2. FILTERS ARE ACCESSED THROUGH THE FRONT OF UNIT. 24" 6" 38 1/4" 26 1/4" 3. CONTROL WIRES SHOULD ENTER CONTROL BOX THROUGH TOP FRONT KNOCKOUT. 4. POWER WIRES ARE TO ENTER CONTROL BOX THROUGH FRONT BOTTOM CONDUIT ENTRANCE KNOCKOUTS. 5. PIPING CONNECTIONS ARE 5/8" OD COPPER. 25 3/16" 15 1/2" 6. STANDARD ENDPOCKET WIDTH IS 7". UNIT WEIGHT 24 1/4" 5" lb ISO1 VIEW (4) 5/8" HANGER HOLES BACK VIEW 9 7/8" AUXILIARY DRAINPAN CONN: MAIN: 7/8" OD TUBE & CLAMP SECONDARY: 3/8" ID TUBE BOTTOM VIEW LEFT VIEW RIGHT VIEW Equipment Submittal Page 14 of 29

82 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A2 Qty: 14 Tag(s): FCU2-1~14 Equipment Submittal Page 15 of 29

83 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A3, A5 Qty: 2 Tag(s): FCU2-15, FCU /8" 2 7/8" MAIN SUPPLY CONN MAIN RETURN CONN MOUNTING FLANGE MOUNTING FLANGE 15 3/8" 14 5/8" FRONT VIEW NOTES: 1. PIPING CONNECTIONS ARE 5/8" OUTSIDE DIAMETER COPPER. 2. LOCATING DIMENSIONS HAVE A PLUS OR MINUS 1" TOLERANCE. Equipment Submittal Page 16 of 29

84 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A3 Qty: 1 Tag(s): FCU2-15 NOTES: 1. ARROW(S) INDICATE THE DIRECTION OF AIRFLOW. 2. FILTERS ARE ACCESSED THROUGH THE FRONT OF UNIT. 24" 6" 38 1/4" 26 1/4" 3. CONTROL WIRES SHOULD ENTER CONTROL BOX THROUGH TOP FRONT KNOCKOUT. 4. POWER WIRES ARE TO ENTER CONTROL BOX THROUGH FRONT BOTTOM CONDUIT ENTRANCE KNOCKOUTS. 5. PIPING CONNECTIONS ARE 5/8" OD COPPER. 25 3/16" 15 1/2" 6. STANDARD ENDPOCKET WIDTH IS 7". UNIT WEIGHT 24 1/4" 5" lb ISO1 VIEW (4) 5/8" HANGER HOLES BACK VIEW 9 7/8" AUXILIARY DRAINPAN CONN: MAIN: 7/8" OD TUBE & CLAMP SECONDARY: 3/8" ID TUBE BOTTOM VIEW LEFT VIEW RIGHT VIEW Equipment Submittal Page 17 of 29

85 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A3 Qty: 1 Tag(s): FCU2-15 Equipment Submittal Page 18 of 29

86 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A4 Qty: 11 Tag(s): FCU3-1~11 NOTES: 1. ARROW(S) INDICATE THE DIRECTION OF AIRFLOW. 2. FILTERS ARE ACCESSED THROUGH THE FRONT OF UNIT. 30" 6" 47 3/4" 35 3/4" 3. CONTROL WIRES SHOULD ENTER CONTROL BOX THROUGH TOP FRONT KNOCKOUT. 4. POWER WIRES ARE TO ENTER CONTROL BOX THROUGH FRONT BOTTOM CONDUIT ENTRANCE KNOCKOUTS. 5. PIPING CONNECTIONS ARE 5/8" OD COPPER. 25 3/16" 15 1/2" 6. STANDARD ENDPOCKET WIDTH IS 7". UNIT WEIGHT 33 3/4" 5" lb ISO1 VIEW (4) 5/8" HANGER HOLES BACK VIEW 9 7/8" AUXILIARY DRAINPAN CONN: MAIN: 7/8" OD TUBE & CLAMP SECONDARY: 3/8" ID TUBE BOTTOM VIEW LEFT VIEW RIGHT VIEW Equipment Submittal Page 19 of 29

87 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A4 Qty: 11 Tag(s): FCU3-1~11 Equipment Submittal Page 20 of 29

88 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A5 Qty: 1 Tag(s): FCU3-12 NOTES: 1. ARROW(S) INDICATE THE DIRECTION OF AIRFLOW. 2. FILTERS ARE ACCESSED THROUGH THE FRONT OF UNIT. 30" 6" 47 3/4" 35 3/4" 3. CONTROL WIRES SHOULD ENTER CONTROL BOX THROUGH TOP FRONT KNOCKOUT. 4. POWER WIRES ARE TO ENTER CONTROL BOX THROUGH FRONT BOTTOM CONDUIT ENTRANCE KNOCKOUTS. 5. PIPING CONNECTIONS ARE 5/8" OD COPPER. 25 3/16" 15 1/2" 6. STANDARD ENDPOCKET WIDTH IS 7". UNIT WEIGHT 33 3/4" 5" lb ISO1 VIEW (4) 5/8" HANGER HOLES BACK VIEW 9 7/8" AUXILIARY DRAINPAN CONN: MAIN: 7/8" OD TUBE & CLAMP SECONDARY: 3/8" ID TUBE BOTTOM VIEW LEFT VIEW RIGHT VIEW Equipment Submittal Page 21 of 29

89 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A5 Qty: 1 Tag(s): FCU3-12 Equipment Submittal Page 22 of 29

90 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A6 Qty: 1 Tag(s): FCU4-1 NOTES: 1. ARROW(S) INDICATE THE DIRECTION OF AIRFLOW. 2. FILTERS ARE ACCESSED THROUGH THE FRONT OF UNIT. 60" 6" 75 1/4" 63 1/4" 3. CONTROL WIRES SHOULD ENTER CONTROL BOX THROUGH TOP FRONT KNOCKOUT. 4. POWER WIRES ARE TO ENTER CONTROL BOX THROUGH FRONT BOTTOM CONDUIT ENTRANCE KNOCKOUTS. 5. PIPING CONNECTIONS ARE 5/8" OD COPPER. 25 3/16" 15 1/2" 6. STANDARD ENDPOCKET WIDTH IS 7". UNIT WEIGHT 61 1/4" 5" lb ISO1 VIEW (4) 5/8" HANGER HOLES BACK VIEW 9 7/8" AUXILIARY DRAINPAN CONN: MAIN: 7/8" OD TUBE & CLAMP SECONDARY: 3/8" ID TUBE BOTTOM VIEW LEFT VIEW RIGHT VIEW Equipment Submittal Page 23 of 29

91 U of A Paty Hall FCU Replacements March 07, 2013 Unit Dimensions - Fan Coil Air Conditioning Units Item: A6 Qty: 1 Tag(s): FCU4-1 Equipment Submittal Page 24 of 29

92 U of A Paty Hall FCU Replacements March 07, 2013 Accessory - Fan Coil Air Conditioning Units Item: A1 - A6 Qty: 310 Tag(s): FCU1-1~282, FCU2-1~15, FCU3-1~12, FCU4-1 Equipment Submittal Page 25 of 29

93 U of A Paty Hall FCU Replacements March 07, 2013 Field Wiring - Fan Coil Air Conditioning Units Item: A1 - A3 Qty: 297 Tag(s): FCU1-1~282, FCU2-1~15 POWER WIRING 115V/60/1 LINE VOLTAGE H N NOTES: 1. ALL FIELD WIRING MUST BE IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC), STATE AND LOCAL REQUIREMENTS. 2. DASHED LINES INDICATE RECOMMENDED FIELD WIRING BY OTHERS. DASHED LINE ENCLOSURES AND / OR DASHED DEVICE OUTLINES INDICATE COMPONENTS PROVIDED BY THE FIELD. SOLID LINES INDICATE WIRING BY TRANE COMPANY. 3. CUSTOMER SUPPLIED FORM C DRY CONTACTS. FIELD WIRING SHOULD BE AWG WITH A MAXIMUM LENGTH OF 1000 FT. DEFAULT SETTINGS: OPEN = OCCUPIED. DISCONNECT SWITCH (BK) MAIN POWER TERMINAL BLOCK (W) GRN ATTACH GROUND 5. INTERCONNECTION WIRING MUST BE AWG AND MUST NOT BE GREATER THAN 200 FT. INTERCONNECTION WIRING SHOULD NOT BE BUNDLED WITH, RUN PARALLEL WITH, OR RUN IN THE SAME CONDUIT WITH ANY HIGH VOLTAGE (110V OR GREATER) WIRES. SHIELDED WIRE (BELDON 83559/83562 OR EQUIVALENT) IS RECOMMENDED IN APPLICATIONS WHERE A HIGH DEGREE OF NOISE IMMUNITY TO RFI IS NEEDED. SHIELD SHOULD BE CONNECTED TO CHASSIS GROUND AT THE UNIT AND TAPED AT THE OTHER END. MCA: 2.75 A MFS: A WARNING HAZARDOUS VOLTAGE! DISCONNECT ALL ELECTRIC POWER INCLUDING REMOTE DISCONNECTS AND FOLLOW LOCK OUT AND TAG PROCEDURES BEFORE SERVICING. INSURE THAT ALL MOTOR CAPACITORS HAVE DISCHARGED STORED VOLTAGE. UNITS WITH VARIABLE SPEED DRIVE, REFER TO DRIVE INSTRUCTIONS FOR CAPACITOR DISCHARGE. FAILURE TO DO THE ABOVE BEFORE SERVICING COULD RESULT IN DEATH OR SERIOUS INJURY. AVERTISSEMENT TENSION DANGEREUSE! COUPER TOUTES LES TENSIONS ET OUVRIR LES SECTIONNEURS À DISTANCE, PUIS SUIVRE LES PROCÉDURES DE VERROUILLAGE ET DES ÉTIQUETTES AVANT TOUTE INTERVENTION. VÉRIFIER QUE TOUS LES CONDENSATEURS DES MOTEURS SONT DÉCHARGÉS. DANS LE CAS D'UNITÉS COMPORTANT DES ENTRAÎNEMENTS À VITESSE VARAIBLE, SE REPORTER AUX INSTRUCTIONS DE L'ENTRAÎNEMENT POUR DÉCHARGER LES CONDENSATEURS. NE PAS RESPECTER CES MESURES DE PRÉCAUTION PEUT ENTRAÎNER DES BLESSURES GRAVES POUVANT ÊTRE MORTELLES. ADVERTENCIA ivoltaje PELIGROSO! DESCONECTE TODA LA ENERGÍA ELÉCTRICA, INCLUSO LAS DESCONEXIONES REMOTAS Y SIGA LOS PROCEDIMIENTOS DE CIERRE Y ETIQUETADO ANTES DE PROCEDER AL SERVICIO. ASEGÚRESE DE QUE TODOS LOS CAPACITORES DEL MOTOR HAYAN DESCARGADO EL VOLTAJE ALMACENADO. PARA LAS UNIDADES CON EJE DE DIRECCIÓN DE VELOCIDAD VARIABLE, CONSULTE LAS INSTRUCCIONES PARA LA DESCARGA DEL CONDENSADOR. EL NO REALIZAR LO ANTERIORMENTE INDICADO, PODRÍA OCASIONAR LA MUERTE O SERIAS LESIONES PERSONALES. CONTROL WIRING 3. OCCUPIED / UNOCCUPIED BI 1 BI 2 BI 3 GND 24V TB1-2 TB1-1 POWER J2-1 J2-2 J2-3 J2-4 J2-5 J2-6 BINARY INPUTS COMM SERVICE J1 TB TB3-2 TB3-3 ZONE GND SET STATUS ZONE SENSOR TB3-4 FAN TEST BINARY OUTPUTS ANALOG INPUTS J3-4 J3-3 J3-2 J3-1 TB3-6 GND AI 2 AI 1 WALL MOUNTED ZONE SENSOR 5. 4 FAN 3 SET NOTICE USE COPPER CONDUCTORS ONLY! 2 GND 1 ZONE UNIT TERMINALS ARE NOT DESIGNED TO ACCEPT OTHER TYPES OF CONDUCTORS. FAILURE TO DO THE ABOVE COULD RESULT IN EQUIPMENT DAMAGE. AVIS N'UTILISER QUE DES CONDUCTEURS EN CUIVRE! LES BORNES DE L'UNITÉ NE SONT PAS CONÇUES POUR RECEVOIR D'AUTRES TYPES DE CONDUCTEURS. FAIRE DÉFAUT À LA PROCÉDURE CI-DESSUS PEUT ENTRAÎNER DES DOMMAGES À L'ÉQUIPEMENT. AVISO UTILICE ÚNICAMENTE CONDUCTORES DE COBRE! LAS TERMINALES DE LA UNIDAD NO ESTÁN DISEÑADAS PARA ACEPTAR OTROS TIPOS DE CONDUCTORES. NO SEGUIR LAS INSTRUCCIONES ANTERIORES PUEDE PROVOCAR DAÑOS EN EL EQUIPO. Equipment Submittal Page 26 of 29

94 U of A Paty Hall FCU Replacements March 07, 2013 Field Wiring - Fan Coil Air Conditioning Units Item: A4, A5 Qty: 12 Tag(s): FCU3-1~12 POWER WIRING 115V/60/1 LINE VOLTAGE H N NOTES: 1. ALL FIELD WIRING MUST BE IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC), STATE AND LOCAL REQUIREMENTS. 2. DASHED LINES INDICATE RECOMMENDED FIELD WIRING BY OTHERS. DASHED LINE ENCLOSURES AND / OR DASHED DEVICE OUTLINES INDICATE COMPONENTS PROVIDED BY THE FIELD. SOLID LINES INDICATE WIRING BY TRANE COMPANY. 3. CUSTOMER SUPPLIED FORM C DRY CONTACTS. FIELD WIRING SHOULD BE AWG WITH A MAXIMUM LENGTH OF 1000 FT. DEFAULT SETTINGS: OPEN = OCCUPIED. DISCONNECT SWITCH (BK) MAIN POWER TERMINAL BLOCK (W) GRN ATTACH GROUND 5. INTERCONNECTION WIRING MUST BE AWG AND MUST NOT BE GREATER THAN 200 FT. INTERCONNECTION WIRING SHOULD NOT BE BUNDLED WITH, RUN PARALLEL WITH, OR RUN IN THE SAME CONDUIT WITH ANY HIGH VOLTAGE (110V OR GREATER) WIRES. SHIELDED WIRE (BELDON 83559/83562 OR EQUIVALENT) IS RECOMMENDED IN APPLICATIONS WHERE A HIGH DEGREE OF NOISE IMMUNITY TO RFI IS NEEDED. SHIELD SHOULD BE CONNECTED TO CHASSIS GROUND AT THE UNIT AND TAPED AT THE OTHER END. MCA: 3.88 A MFS: A WARNING HAZARDOUS VOLTAGE! DISCONNECT ALL ELECTRIC POWER INCLUDING REMOTE DISCONNECTS AND FOLLOW LOCK OUT AND TAG PROCEDURES BEFORE SERVICING. INSURE THAT ALL MOTOR CAPACITORS HAVE DISCHARGED STORED VOLTAGE. UNITS WITH VARIABLE SPEED DRIVE, REFER TO DRIVE INSTRUCTIONS FOR CAPACITOR DISCHARGE. FAILURE TO DO THE ABOVE BEFORE SERVICING COULD RESULT IN DEATH OR SERIOUS INJURY. AVERTISSEMENT TENSION DANGEREUSE! COUPER TOUTES LES TENSIONS ET OUVRIR LES SECTIONNEURS À DISTANCE, PUIS SUIVRE LES PROCÉDURES DE VERROUILLAGE ET DES ÉTIQUETTES AVANT TOUTE INTERVENTION. VÉRIFIER QUE TOUS LES CONDENSATEURS DES MOTEURS SONT DÉCHARGÉS. DANS LE CAS D'UNITÉS COMPORTANT DES ENTRAÎNEMENTS À VITESSE VARAIBLE, SE REPORTER AUX INSTRUCTIONS DE L'ENTRAÎNEMENT POUR DÉCHARGER LES CONDENSATEURS. NE PAS RESPECTER CES MESURES DE PRÉCAUTION PEUT ENTRAÎNER DES BLESSURES GRAVES POUVANT ÊTRE MORTELLES. ADVERTENCIA ivoltaje PELIGROSO! DESCONECTE TODA LA ENERGÍA ELÉCTRICA, INCLUSO LAS DESCONEXIONES REMOTAS Y SIGA LOS PROCEDIMIENTOS DE CIERRE Y ETIQUETADO ANTES DE PROCEDER AL SERVICIO. ASEGÚRESE DE QUE TODOS LOS CAPACITORES DEL MOTOR HAYAN DESCARGADO EL VOLTAJE ALMACENADO. PARA LAS UNIDADES CON EJE DE DIRECCIÓN DE VELOCIDAD VARIABLE, CONSULTE LAS INSTRUCCIONES PARA LA DESCARGA DEL CONDENSADOR. EL NO REALIZAR LO ANTERIORMENTE INDICADO, PODRÍA OCASIONAR LA MUERTE O SERIAS LESIONES PERSONALES. CONTROL WIRING 3. OCCUPIED / UNOCCUPIED BI 1 BI 2 BI 3 GND 24V TB1-2 TB1-1 POWER J2-1 J2-2 J2-3 J2-4 J2-5 J2-6 BINARY INPUTS COMM SERVICE J1 TB TB3-2 TB3-3 ZONE GND SET STATUS ZONE SENSOR TB3-4 FAN TEST BINARY OUTPUTS ANALOG INPUTS J3-4 J3-3 J3-2 J3-1 TB3-6 GND AI 2 AI 1 WALL MOUNTED ZONE SENSOR 5. 4 FAN 3 SET NOTICE USE COPPER CONDUCTORS ONLY! 2 GND 1 ZONE UNIT TERMINALS ARE NOT DESIGNED TO ACCEPT OTHER TYPES OF CONDUCTORS. FAILURE TO DO THE ABOVE COULD RESULT IN EQUIPMENT DAMAGE. AVIS N'UTILISER QUE DES CONDUCTEURS EN CUIVRE! LES BORNES DE L'UNITÉ NE SONT PAS CONÇUES POUR RECEVOIR D'AUTRES TYPES DE CONDUCTEURS. FAIRE DÉFAUT À LA PROCÉDURE CI-DESSUS PEUT ENTRAÎNER DES DOMMAGES À L'ÉQUIPEMENT. AVISO UTILICE ÚNICAMENTE CONDUCTORES DE COBRE! LAS TERMINALES DE LA UNIDAD NO ESTÁN DISEÑADAS PARA ACEPTAR OTROS TIPOS DE CONDUCTORES. NO SEGUIR LAS INSTRUCCIONES ANTERIORES PUEDE PROVOCAR DAÑOS EN EL EQUIPO. Equipment Submittal Page 27 of 29

95 U of A Paty Hall FCU Replacements March 07, 2013 Field Wiring - Fan Coil Air Conditioning Units Item: A6 Qty: 1 Tag(s): FCU4-1 POWER WIRING 115V/60/1 LINE VOLTAGE H N NOTES: 1. ALL FIELD WIRING MUST BE IN ACCORDANCE WITH THE NATIONAL ELECTRIC CODE (NEC), STATE AND LOCAL REQUIREMENTS. 2. DASHED LINES INDICATE RECOMMENDED FIELD WIRING BY OTHERS. DASHED LINE ENCLOSURES AND / OR DASHED DEVICE OUTLINES INDICATE COMPONENTS PROVIDED BY THE FIELD. SOLID LINES INDICATE WIRING BY TRANE COMPANY. 3. CUSTOMER SUPPLIED FORM C DRY CONTACTS. FIELD WIRING SHOULD BE AWG WITH A MAXIMUM LENGTH OF 1000 FT. DEFAULT SETTINGS: OPEN = OCCUPIED. DISCONNECT SWITCH (BK) MAIN POWER TERMINAL BLOCK (W) GRN ATTACH GROUND 5. INTERCONNECTION WIRING MUST BE AWG AND MUST NOT BE GREATER THAN 200 FT. INTERCONNECTION WIRING SHOULD NOT BE BUNDLED WITH, RUN PARALLEL WITH, OR RUN IN THE SAME CONDUIT WITH ANY HIGH VOLTAGE (110V OR GREATER) WIRES. SHIELDED WIRE (BELDON 83559/83562 OR EQUIVALENT) IS RECOMMENDED IN APPLICATIONS WHERE A HIGH DEGREE OF NOISE IMMUNITY TO RFI IS NEEDED. SHIELD SHOULD BE CONNECTED TO CHASSIS GROUND AT THE UNIT AND TAPED AT THE OTHER END. MCA: 6.07 A MFS: A WARNING HAZARDOUS VOLTAGE! DISCONNECT ALL ELECTRIC POWER INCLUDING REMOTE DISCONNECTS AND FOLLOW LOCK OUT AND TAG PROCEDURES BEFORE SERVICING. INSURE THAT ALL MOTOR CAPACITORS HAVE DISCHARGED STORED VOLTAGE. UNITS WITH VARIABLE SPEED DRIVE, REFER TO DRIVE INSTRUCTIONS FOR CAPACITOR DISCHARGE. FAILURE TO DO THE ABOVE BEFORE SERVICING COULD RESULT IN DEATH OR SERIOUS INJURY. AVERTISSEMENT TENSION DANGEREUSE! COUPER TOUTES LES TENSIONS ET OUVRIR LES SECTIONNEURS À DISTANCE, PUIS SUIVRE LES PROCÉDURES DE VERROUILLAGE ET DES ÉTIQUETTES AVANT TOUTE INTERVENTION. VÉRIFIER QUE TOUS LES CONDENSATEURS DES MOTEURS SONT DÉCHARGÉS. DANS LE CAS D'UNITÉS COMPORTANT DES ENTRAÎNEMENTS À VITESSE VARAIBLE, SE REPORTER AUX INSTRUCTIONS DE L'ENTRAÎNEMENT POUR DÉCHARGER LES CONDENSATEURS. NE PAS RESPECTER CES MESURES DE PRÉCAUTION PEUT ENTRAÎNER DES BLESSURES GRAVES POUVANT ÊTRE MORTELLES. ADVERTENCIA ivoltaje PELIGROSO! DESCONECTE TODA LA ENERGÍA ELÉCTRICA, INCLUSO LAS DESCONEXIONES REMOTAS Y SIGA LOS PROCEDIMIENTOS DE CIERRE Y ETIQUETADO ANTES DE PROCEDER AL SERVICIO. ASEGÚRESE DE QUE TODOS LOS CAPACITORES DEL MOTOR HAYAN DESCARGADO EL VOLTAJE ALMACENADO. PARA LAS UNIDADES CON EJE DE DIRECCIÓN DE VELOCIDAD VARIABLE, CONSULTE LAS INSTRUCCIONES PARA LA DESCARGA DEL CONDENSADOR. EL NO REALIZAR LO ANTERIORMENTE INDICADO, PODRÍA OCASIONAR LA MUERTE O SERIAS LESIONES PERSONALES. CONTROL WIRING 3. OCCUPIED / UNOCCUPIED BI 1 BI 2 BI 3 GND 24V TB1-2 TB1-1 POWER J2-1 J2-2 J2-3 J2-4 J2-5 J2-6 BINARY INPUTS COMM SERVICE J1 TB TB3-2 TB3-3 ZONE GND SET STATUS ZONE SENSOR TB3-4 FAN TEST BINARY OUTPUTS ANALOG INPUTS J3-4 J3-3 J3-2 J3-1 TB3-6 GND AI 2 AI 1 WALL MOUNTED ZONE SENSOR 5. 4 FAN 3 SET NOTICE USE COPPER CONDUCTORS ONLY! 2 GND 1 ZONE UNIT TERMINALS ARE NOT DESIGNED TO ACCEPT OTHER TYPES OF CONDUCTORS. FAILURE TO DO THE ABOVE COULD RESULT IN EQUIPMENT DAMAGE. AVIS N'UTILISER QUE DES CONDUCTEURS EN CUIVRE! LES BORNES DE L'UNITÉ NE SONT PAS CONÇUES POUR RECEVOIR D'AUTRES TYPES DE CONDUCTEURS. FAIRE DÉFAUT À LA PROCÉDURE CI-DESSUS PEUT ENTRAÎNER DES DOMMAGES À L'ÉQUIPEMENT. AVISO UTILICE ÚNICAMENTE CONDUCTORES DE COBRE! LAS TERMINALES DE LA UNIDAD NO ESTÁN DISEÑADAS PARA ACEPTAR OTROS TIPOS DE CONDUCTORES. NO SEGUIR LAS INSTRUCCIONES ANTERIORES PUEDE PROVOCAR DAÑOS EN EL EQUIPO. Equipment Submittal Page 28 of 29

96 U of A Paty Hall FCU Replacements March 07, 2013 Field Installed Options - Part/Order Number Summary This is a report to help you locate field installed options that arrive at the jobsite. This report provides part or order numbers for each field installed option, and references it to a specific product tag. It is NOT intended as a bill of material for the job. Product Family - Fan Coil Air Conditioning Units Item Tag(s) Qty Description Model Number A1 FCU1-1~282, 282 Fan Coil Air Conditioners (UniTrane) FCDB040 A2 FCU2-1~14 14 Fan Coil Air Conditioners (UniTrane) FCBB040 A3 FCU Fan Coil Air Conditioners (UniTrane) ( FCBB040 A4 FCU3-1~11 11 Fan Coil Air Conditioners (UniTrane) ( FCBB060 A5 FCU Fan Coil Air Conditioners (UniTrane) ( FCBB060 A6 FCU4-1 1 Fan Coil Air Conditioners (UniTrane) ( FCBB100 Field Installed Option Description Wall mounted temperature sensor (set point, OALMH) Part/Ordering Number X Equipment Submittal Page 29 of 29

97 CERTIFICATION OF COMPLIANCE WITH THE STATE OF ALABAMA IMMIGRATION LAW The undersigned officer of (Company) certifies to the Board of Trustees of the University of Alabama that the Company does not employ an individual or individuals within the State of Alabama. SIGNATURE OF COMPANY OFFICER PRINT COMPANY NAME PRINT NAME OF COMPANY OFFICER PRINT TITLE OF COMPANY OFFICER DATE

98 Welcome User ID Last Login Log Out Click any for help Home My Cases New Cases View Cases Search Cases My Profile Edit Profile Change Password Change Security Questions My Company Edit Company Profile Add New User View Existing Users Close Company Account My Reports View Reports My Resources View Essential Resources Take Tutorial View User Manual Contact Us Company Information Company Name: Company ID Number: Doing Business As (DBA) Name: DUNS Number: Physical Location: Mailing Address: Address 1: Address 1: Address 2: Address 2: City: State: Zip Code: County: Additional Information: Employer Identification Number: Total Number of Employees: Parent Organization: Administrator: Organization Designation: Employer Category: Federal Contractor Category: Employees being verified: City: State: Zip Code: View/Edit NAICS Code: View/Edit Total Hiring Sites: View/Edit Total Points of Contact: View/Edit View MOU U.S. Department of Homeland Security - U.S. Citizenship and Immigration Services - Accessibility Download Viewers

99 DISCLOSURE STATEMENT 1. Contract/Purchase Order No. 2. Name of Contract/Grantee: Address: Telephone: Fax: 3. Nature of Contract/Grant: 4. Does the contractor/grantee have any relationships with any employee or official of the University, or a family member of such employee or official, that will enable such employee or official, or his/her family member, to benefit from this contract? If so, please state the names, relationships, and nature of the benefit. (For employees of the University, family members include spouse and dependents. For members of the Board of Trustees (officials), family members include spouse, dependents, adult children and their spouses, parents, in-laws, siblings and their spouses.) This Disclosure Form will be available for public inspection upon request. The above information is true and accurate, to the best of my knowledge. Signature of Authorized Agent of Contractor/Grantee Date: RETURN FORM TO: The University of Alabama Purchasing Dept. Box Tuscaloosa, AL Ph: (205) Fax: (205)