2. FEATURES & TECHNICAL EXPLANATION

Transcription

1 2. FEATUES & TECHNICAL EXPLANATION 2-.FEATUES ÆLOW TANGLE AND LOW DAMAGE. Drum washing machine have uniform washing without damage and tangle by rubbing and beating. ÆADOPT FUZZY LOGIC. FUZZY denote that MICOM can set the optimal washing process by sensing laundry amount and temperature of ambience and water. ÆLOW-ISE. Low-noise washing and spinning is accomplished by adopting electronic motor control. ÆLIGHT-WEIGHT. By reducing the weight of system dramatically to 63kg, it is easy to handle. ÆESEVATION. (DELAYED STAT) If necessary, the reservation time for washing can be set up by controlling the (TIME DELAY) button. ÆEASY CHECK OF THE WATE TEMPEATUE IN WASHING. Water temperature is displayed by pressing the selection (WATE TEMP) button on washing. ÆWHEN THE SETTING TEMPEATUE IS OVE 60. Washed water is gradually decreased by repeating WATE INLET-INSE-DAIN to prevent the laundry from damage by water temperature sudden change. ÆPOWE SHOWE INSE. The front of door sprays out the water to remove the remaining detergent with just a little amount water. ÆPEFEED TEMPEATUE SELECTION. Selected temperature from cold to heating(6 steps). ÆCHILD-LOCK. The Child-Lock system has been developed to prevent children from processing any button to change the program during operation. ÆINSE HOLD. If you desire to leave your synthetic and wool fabrics in the machine after the wash program you may select the (INSE HOLD) function to prevent them from getting wrinkled. ÆAuto estart Although the washing machine is turned off by a power failure, it restarts automatically in its stopped again and the process is properly adjusted and it will be the same when the machine unplugged in operation is plugged in again. 4

2 2-2.SENSING THE LAUNDY AMOUNT PINCIPLE : After the first water supply, the laundry absorbs the water with the revolution of drum, which causes the decrease of water level. Micro-Processor senses decreased water level and makes water to be supplied more and recognizes he amount of the laundry by calculating the times of complementary water supply. Criteria : AMOUNT OF LAUNDY below 2.0 above 4.5 TIMES OF COMPLEMENTAY WATE SUPPLY ~2 times 3 times or more The times of water supply depends on amount of laundry, material of laundry and water temperature etc. 2-3.DETEMINE WASHING TIME BY FUZZY LOGIC To get the best washing performance optimal time is determined by sensing of water temperature, selected washing temperature and laundry amount. water temperature washing time selected washing temperature FUZZY LOGIC rinse time the best washing performance laundry amount spin rhythm, time SENSING POCESSING DETEMINATION EFFECT 2-4.WATE LEVEL CONTOL This model adopts a pressure sensor which can sense the water level in the tub. When the water level reaches to the preset level water supply is stopped, then washing program proceeds. Spinning does not proceed until the water in the tub reduces to a certain level. 5

3 2-5.CONTOL OF DOO OPEN ƒuthe door can be opened by pressing (DOO OPEN) button after finishing program. ƒuwhen the revolution of drum is stopped and in case water level is below level 2, door can be opened by pressing the (DOO OPEN) button. ƒuif there is no power, the door can be opened by revolving the door opener. (If the water level is high, first drain the water by pulling out the hose cap) 2-6.IN CASE OF T OPEN THE DOO ƒupower is off or unplugged. ƒuprogram is operating. ƒu(doo LOCK) light turn on. door lock ƒumotor(drum) is spinning(otating). 2-7.IN CASE OF ADOO LOCK BLIGHT TUNS ON ƒuwater level frequency is below 23.2kHz.(Water level is high) ƒuin the tub water temperature above 45 6

4 4. INSTALLATION Before servicing ask troubles of customers Check the adjustment(power supply is V, remove the transit bolts...) ŁCheck the troubles referring to the trouble shooting. ØDecide the step of service referring to disassembly and instructions. ŒAnd then, service and repair. ºAfter servicing, operate the appliance whether it works O K or T. ÆSTANDAD INSTALLATION The appliance should be installed as follows. EMOVE THE TANSIT INSTALL THE APPLIANCE ADJUST THE BOLTS ON FLAT AND FIM SUFACE HOIZONTAL ƒuemove the transit bolts (4EA: )with supplied spanner. ƒuturn the leveling feet to set the appliance horizontally. ƒukeep the transit bolts and spanner for future use. ƒuinsert the 4 caps( Ł)provided into the hole Low 2 High ƒuthe appliance goes up by rotating the feet clockwise direction. ƒuthe appliance come down by rotating the feet counter clockwise direction. 8

5 Æ HOW TO CONNECT INLET HOSE ƒucheck that the rubber packing is inside of the valve connector. ƒuconnect the inlet hose firmly to prevent leak. ÆCONNECT DAIN HOSE Make sure that the hose is not twisted. Avoid submerging the end of the hose. The drain hose should be placed under 85 flfrom the floor. ÆCONNECT POWE PLUG Connect the power plug to the wall outlet. Avoid connecting several electric devices, It may be the cause of the fire. 9

6 GTEST OPEATION Preparation for washing. Press the POWE ( ) button. Press the POGAM ( P ) button. Press the (STAT/PAUSE) ( ) button. P ƒuconnect the power plug to the outlet. ƒuconnect the inlet hose. In case of coloreds program. In case of coloreds program. Check the water heating. Check automatic reverse Check the water supply. turn. Press the button (WATE TEMP) ( ) and then the present temperature in displayed. Check if the drum rotates to clockwise and counterclockwise. Check shower because the water supplied on the door at first. Check the drain and spin Power off Water removal Pre 200 inse hold Super Main 600 Normal no Spin (Wash) (inse) (Spin) After power off, press the DOO OPEN ( ) button to check the door open. If SVC is needed, during check and remove the remaining water by pulling out the hose cap. ƒutrouble shooting refer to (7.EO DISPLAY) ƒuassemble and disassemble refer to (9.Disassembly Instructions) 0

7 6. WIING DIAGAM 3

8 7. TOUBLE SHOOTING 7-.BEFOE SVC CHECKING ÆBe careful of electric shock or disconnecting the parts while trouble shooting. ÆVoltage of each terminal in AC V and DC while applying an electric current. 7-2.QC TEST MODE. Pressing INSE( ), and SPIN ( )button simultaneously. ŁPower supply ON with pressing upper two button. then buzzer sound twice. ØPress the STAT/PAUSE ( )button as follows. apress the STAT/PAUSE ( )button more 4 times until stop spinning b Pressing number of STAT/PAUSE button None Checking Point All lamps turn on Display Status time Clockwise spin(right) Motor rpm(about 45) 2 times Low speed Spin Motor rpm(about 63~67) 3 times High speed Spin Motor rpm(about 4~7) 4 times Inlet valve for pre-wash operation Water level frequency(25~65) 5 times Inlet valve for main-wash operation Hot inlet valve in case of hot water fill Water level frequency(25~65) 6 times Inlet valve for main-wash operation Water level frequency(25~65) 7 times Counterclockwise spin(left) Motor rpm(about 45) 8 times A Heater is in operation for 3 sec. Water Temperature 9 times Draining pump operation Water level frequency 0 times Auto off operation 7-3.HOW TO KW THE WATE LEVEL FEQUENCY ƒpress the WASH ( ) and INSE ( ) button simultaneously. The digits means water level frequency(0 - ) ex) 24 : Water level frequency = =24. 4

9 7-4.EO DISPLAY. ƒuif you press the astart/pause b button in error condition, any error except ÔPEÕ will disappear and the machine will change into pause status. ƒuin case of GPE H, GtE H, GdE H, if the error is not resolved within 20 sec., and in case of other errors, if the error is not resolved within 4 min., power will be turned off automatically and the error only will be blinked. But in case of GFE H, power will not be turned off. EO SYMPTOM CAUSE WATE INLET Water has not reached to the pre-set level within 4 min. since EO INLET inlet valve operated or water has not reached to the normal level within 25 min. 2 IMBALANCE IMBALANCE The appliance is tilted. EO Laundry is gatherd to one side. Non distributable things are put into the drum. 3 DAIN EO DAIN Water has not drained enough within 5 min. 4 OVE FLOW Water is automatically being pumped out because too much EO water is in the tub. 5 SENSO PESSUE S/W EO The sensor pressure switch is out of order. 6 DOO OPEN The astart/pause b button is pressed with the door open. EO The door switch is out of order. 7 HEATING EO The thermistor is out of order. 8 SENSO The connector (5pin, male, white) in the Wire Harness is not EO connected to the connector (5 pin, female) of Hall Sensor in the MOTO. ƒ_õ reconnect or repair the contact in the connector 5

10 EO SYMPTOM CAUSE 8 9 SENSO EO CUENT EO The electric contact between the connectors (5 pin, male in the Wire Harness and 5 pin female in the Hall Sensor) is bad or unstable. ƒ_ econnect or repair the contact in the connector The connector (6 pin, male, natural) in the Wire Harness is not connected to the connector (6 pin, female, natural) of PWB ASSY(Main) or the electric contact of connectors is bad/unstable. ƒ_ econnect or repair the contact in the connector The electric contact between the connectors a6 pin, male in the Wire Harness and 6 pin female in the controller(main) bis bad or unstable. ƒ_ econnect or repair the contact in the connector The Wire Harness between Hall Sensor in the MOTO and PWB ASSY(Main) is cut(open circuited). ƒ_ epair/replace the damaged WIE HANESS The Hall Sensor is out of order/defective. ƒ_ eplace the Motor The controller(main) is out of order/defective. ƒ_ eplace the PWB ASSY(Main) PWB ASSY(Main) is out of order ƒ_ eplace the PWB ASSY(Main) Winding in the MOTO is short-circuited. ƒ_ eplace the MOTO 0 LOCK EO The Connector(3 pin, male, white) in the Wire Harness is not connected to the Connector(3 pin, female, white) of MOTO. ƒ_ econnect or repair the connector The electric contact between the connectors a3 pin, male, white in the Wire Harness and 6 pin, female, white in the PWB ASSY(Main) bis bad or unstable. ƒ_ econnect or repair the contact in the connector The Wire Harness between the MOTO and PWB ASSY(Main) is cut(open circuited). ƒ_ epair the damaged(open-circuited) WIE HANESS The hall sensor is out of order/defective. ƒ_ eplace the PWB ASSY(Main) 6

11 8. EO DIAGSIS AND CHECK LIST 8-.DIAGSIS AND ANSWE FO ABMAL OPEATION SYMPTOM GUIDE FO SEVICE CALL POWE Is the power plug connected firmly to AC V outlet? Power failure? or Breaker opened? Visit to check Water inlet trouble Is "no inlet" displayed? no inlet no inlet Is the tap opened? Is the tap frozen? Is the water supply shut-off? Is filter in the inlet valve clogged with foreign material? Clean the filter of inlet valve Visit to check 7

12 SYMPTOM GUIDE FO SEVICE CALL Door open trouble Error displayed on the program When the door opened, Is the started or on the program C TIME DELAY D? Close the door Didn't you press the DOO OPEN ( ) button when water remained in the tub?. Press the STAT/PAUSE ( ) button to stop the appliance. 2. Drain water by selecting spin. 3. Open the door by pressing the DOO OPEN( ) button. Isn't door opened in spite of pressing the DOO OPEN ( ) button Visit to check Check if the door switch is O K. µ Drain Trouble Is "no drain" displayed? no drain no drain Is the foreign material clogged in the drain pump filter such as pin, coin and etc.? Clean up the filter. Is the Drain Hose frozen with water, kinked or curshed? Visit to check 8

13 SYMPTOM Lather overflow from the appliance. (In this condition, wash and spin do not operate normally) GUIDE FO SEVICE CALL Is Low-lathering detergent for the drum washing machine used? Is the proper amount of detergent used as recommended? ecommend to reduce the using amount of detergent. LOW LATHEING DETEGENT ƒtthis appliance has the automatic suds sensing function which operates under much suds condition for good rinse and preventing overflow. ƒt When much suds are sensed, suds removing fuction such as drain, water input and pause will operate without rotating the drum. No effect of softener Is softener put in the correct compartment of drawer? Is the drawer closed during wash? Compartment for softener Is the softener cap clogged? Explain how to use softener Clean the compartment for softener µ Error displayed as follows Visit to check 9

14 8-2.FAULT DIAGSIS AND TOUBLE SHOOTING CAUTION. Be careful of electric shock or disconnecting the parts while trouble shooting. 2. First of all, check the connection of each part terminal with wiring diagram. POWE When measuring the voltage of the outlet, is the voltage AC V? Check the fuse? () Is the LED() on? eplace PWB assy (Main) <PWB ASSY (MAIN)> (2) (5) (6) When measuring the voltage of natural connector(5,6) is the voltage DC 0~6.5V? eplace PWB assy(main) <PWB ASSY (MAIN)> Is connector(2) disconnected or disassembled? econnect the PWB assy (Display) Is wire of the PWB assy(display) disconnected? econnect the PWB assy (Display) eplace PWB assy(display) (687FC2272D) 20

15 WATE SUPPLY Is the water supply shut-off? Is tap opened? When you press both WASH( )button and INSE( ) buttons simultaneously, is the water level frequency below 240? Is the inlet valve filter clogged with impurity? Is resistance of the inlet valve connector between 2 to 8 k? Check the voltage between each terminal of inlet valve is AC 220~240V. (efer to 7-2 TEST MODE) Open the tap. Check the chamber(air) and the tube clogged with impurity. Clean the filter. eplace the inlet valve. eplace the PWB assy (Main). DETEGENT DOES T FLOW IN Is the water supplied? efer to solution Ano inlet B Wiring diagram Are receptacles correctly connected to the therminals of inlet valve? Check the wiring on the dispenser. SOFTENE MAIN PE - WASH WASH MAX Is detergent put in the correct compartment of the drawer? Put the detergent in the correct position PE+MAIN MAIN WASH : Detergent Is the detergent hardened? Clean the drawer. 2

16 SOFTENE DOES T FLOW IN Is the water supplied? efer to A WATE SUPPLY B Wiring diagram Are receptacles correctly connected to the terminals of inlet valve? Check the wiring on the dispenser. MAX Is the softener put in the correct compartment of drawer? Put in the correct compartment. Is the softener cap clogged? Clean the cap and drawer. ABMAL SOUND Is the pulley bolt loosened? Fix the bolt tightly. Is the belt worn? eplace the V-belt (4400F36A) Is there friction noise from the motor? eplace the motor. 22

17 HEATING WITHOUT WATE When pressing WASH ( ) and INSE ( )button at the same time after draining, is the water level frequency 252 or more? When pressing WASH ( ), INSE ( ) buttons at the same time while wash, is the water level frequency between 220~240? eplace the sensor (pressure) PWB ASSY(Main) Checking voltage between two pins as press the power Button is the voltage AC 220~240V? eplace the PWB assy (Main) AC V DAIN MALFUNCTIONING Is the drain hose twisted or frozen? epair drain hose Is the impeller of drain pump clogged? emove foreign material. Is the connector disconnected, disassembled? econnect or repair the connector Is the coil of drain pump cut-off? (resistance of coil is 90~60 ) eplace the pump assy (6) (5) PWB ASSY(Main) 2 When checking voltage between connectors ( L, M)on spinning, is the voltage AC V as the figure? eplace the PWB assy (Main) 23

18 WASH HEATE TOUBLE PWB ASSY(Main) When checking the voltage between connector the PWB assy(main)during whites washing,is the voltage 220 ~ 240V? eplace the PWB assy (Main) AC V ED YELLOW After power off,is the resistance of wire (ED-YELLOW) connectors between 0 to 30? Normal After power off and the heater terminal is disconnected, is the resistance 0 to 30? eplace the heater assy HEATING CONTINUOUSLY ABOVE THE SETTING WATE TEMPEATUE () When disconnect the connector() on the PWB assy (Main) is the resistance of the Natural connectors a Ł( Blue/White, Violet), Ø(Blue, White) bbetween 2.5k to 80k (05 ~0 )? eplace the thermistor (6322F2046B) When checking thermistor on the tub cover, is the thermistor loosened above 2mm from the rubber? Push the thermistor tightly to the rubber. 24

19 SPIN TOUBLE (WASH) (INSE) Check on the spinning, is the frequency of the water level 248 or more. The frequency can be checked by pressing the WASH ( ) and INSE ( ) buttons at the same time on the program. Check the sensor (Pressure) or hose (Sensor). If the problem is on the sensor or the hose, replace the sensor or the hose. (INSE) (SPIN) When pressing INSE( ), SPIN( ) and POWE( ) buttons at the same time after power off, press the STAT/PAUSE ( )button 2 times, is the drum low speed spin? Normal () Is it disconnected, or disassembled? aed:3pin() b Correct the connector. Check the motor connector, is the resistance of the terminal same as the figure? MOTO TEMINAL eplace the motor assy. (468F24B) 3 Ł Ø 2 esistance of terminal: ~ Ł / Ł~ Ø / Ø~ : About 6.5 eplace the PWB assy (Main) 25

20 9. DISASSEMBLY INSTUCTIONS ƒdisassemble and repair the parts after pulling out power cord from the outlet CONTOL PANEL PLATE ASSY(TOP) Two screws are unscrewed on the top plate. ŁThe plate assy(top) is pulled back and then upward to arrow direction. Hook The PWB assy(display) connectors are disconnected. ŁPull out drawer, three screws are unscrewed. ØPush two upper hooks and pull the control panel forward. PANEL ASSY(CONTOL) PWB ASSY(DISPLAY) The PWB assy(display) is disconnected. ŁWhen 9 screws are unscrewed on the PWB insulator and the PWB assy(display) is disassembled from the PWB insulator. 26

21 DISPENSE ASSY Disassemble the top plate assy. ŁPull the drawer to arrow direction. ØTwo screws are unscrewed. DAWE Valve(Hot) The hose clamps and the hose are disassembled. ŁThe ventilation bellows and the water inlet bellows are disassembled on the tub. 27

22 INLET VALVE 3 2 Disconnect the wiring connector. ŁUnscrew 2 screws from the back. ƒtwhen reconnecting the connector VALVE#(MAIN) VALVE#2(PE) White/Black - Black Gray/ White - Black VALVE#3(HOT) Blue/ed-Black awd-223fh/225fh/243fh/245fh b PWB ASSY(MAIN) The back cover is removed. ŁUnscrew 2 screws Ø Pull the PWB assy (Main) as shown. 28

23 LOWE COVE Open the lower cover cap by using coin and remove the lower cover to arrow direction after screw is unscrewed. DOO When the power cord is plugged, the door can be opened by pushing the DOO OPEN ( ) button Open the door completely. Łemove the two screws from the hinge. EMEGENCY DOO ELEASE Door opening method in case of no electricity otate the emergency door release counterclockwise, by a coin. 0 emoving method of remained water Drain plug (emaining Hose) otate the drain plug (remaining hose) to arrow direction. ŁPull it out from hose. First, prepare a bucket to put in the remained water 29

24 GASKET ASSY The cabinet gasket clamp is released. ŁTwo screws are unscrewed from the cabinet cover. Three screws are unscrewed from the lower cover. ŁThe lower cover is disassembled. The control panel is removed. ŁScrew is unscrewed from the cabinet cover. Take apart the tub gasket clamp ŁMake sure that the drain hole of the gasket is put beneath when reassembling the gasket. efer to the arrow mark on the tub cover. 30

25 PULLEY, MOTO, DAMPE The back cover is removed. ŁThe belt is pulled off while turning over the pulley. ØThe bolt is unscrewed to the shaft and then the pulley pulled off. (PULLEY) 2 3 Two screws are unscrewed from the bracket(motor). ŁThe motor is pushed to arrow direction and then it is disassembled. (When mounting the rubber should be fit the bracket holder<motor>) (MOTO) Hinge, Damper Damper Lay the washing machine. ŁThe hinge(damper) at the tub is pulled off pressing on the snaps at the sharp end. ØThe hinge at the base is pulled off. (DAMPE) 3

26 PUMP Pump Outlet Hose emove the pump outlet hose. Łemove the tub pump hose. ØThe pump connectors are disconnected, the hose is pulled off. ŒThree screws are unscrewed. ºThe pump is disassembled to arrow direction. Tub Pump Hose HEATE Three screws are unscrewed. ŁThe heater M6 bolt is loosened and it is released through the tub cover. CAUTION When mounting the heater, the heater should be inserted the heater clip on the bottom of the tub. THEMISTO Pull it out by holding the thermistor bracket. ƒtif holding the wire and pulling out it, it may be broken. ƒtthe thermistor should be checked it is pulled to the rubber tightly. 32

27 DOO HINGE ASSY Two screw are unscrewed on the door and the door is disassembled. ŁThe cabinet cover clamp is removed and the gasket is released. ØTwo screws are unscrewed on the door hinge. ŒThe door hinge is disassembled by pushing the door hinge arm inside the cabinet cover. SWITCH ASSY, DOO LOCK The cabinet cover clamp is removed and the gasket is released. ŁTwo screws are unscrewed. ØThe Door Lock S/W is disconnected from the wiring connector and the strap. WHEN FOEIGN MATEIAL STACK BETWEEN DUM AND TUB The heater is removed. ŁThe foreign material(wire, coin, etc) is removed by inserting the long bar in the hole. 33

28 0. EXPLODED VIEW AND PAT LIST 0-.THE PAT LIST OF CABINET ASSY A- A-2 A-47 A-45 A-5 A-39 A-44 A-38 A-43 A-37 A-6 A-35 A-34 A-7 A-36 A-33 A-32 A-3 A-0 A-30 A-29 A-27 A-28 A- A-5 A-26 A-25 A-24 A-53 A-3 A-4 A-5 A-6 A-7 A-23 A-49 A-2 A-22 A-8 34

29 ÆTHE PAT LIST OF CABINET ASSY L/No. PAT NAME PAT. SVC COD Q flty SPEC A- PLATE ASSY(TOP) 330E00 A-2 SCEW, TAPPING TUSS HEAD TTL A-5 BACK COVE 3808F202A A-6 SCEW, TAPPING TUSS HEAD TTG A-7 CABINET ASSY 390F0045 A-0 POWE COD ASSY 64F69B C-4-2 *See Appendix(type of power cord) 64F69D S-2-64F69E B-5 64F69F B-3 64F69K B-3(BSI) 64F69L B-3(SISI) 64F69N C F69P S F69Q S-2- A- SCEW 4000W4A003A 4 A-3 SCEW, TAPPING TUSS HEAD TTG A-4 SENSO PESSUE 6600F704S A-5 BASE 3040F0049A A-6 SCEW, TAPPING TUSS HEAD TTG A-7 BACKET, BASE 480F436A 4 A-8 FEET ASSY 543F454A 4 A-2 COVE, LOWE 3550F66 A-22 SCEW, TAPPING TUSS HEAD TTL A-23 CAP(EMAINING HOSE) 5006F346 A-24 OPENE, DOO 5870F347 A-25 STAP 4640F48A A-26 CLAMP ASSY, CABINET GASKET 2W2007A 35

30 L/No. PAT NAME PAT. SVC COD Q flty SPEC A-27 GUIDE 4974F445 A-28 SCEW 4000FD49A 2 A-29 SCEW, TAPPING TUSS HEAD TTL A-30 SWITCH ASSY, DOO LOCK 660F9C VAC A-3 SCEW 660F262A 4000FD49A VAC (EMZ) A-32 HINGE ASSY 4775F24B A-33 SCEW, TAPPING TUSS HEAD TTL A-34 COVE, CABINET 3550F23 A-35 SCEW, TAPPING PAN HEAD TPL A-37 HOLDE 4930F457A 2 A-38 HOLDE 4930E400A 3 A-39 SCEW, TAP TITE(S) PAN HEAD SCPF A-43 HOLDE 4930F35A A-44 BOLT ASSY, TANSIT 40F359A 4 A-45 BUSHING 4830F307 A-47 DOO ASSY 358F200D A-49 LOWE COVE CAP 5006F379 A-5 SCEW TAPPING TUSS HEAD TTL A-53 PWB ASSY(MAIN) 687EC VAC 36

31 0-2 THE EXPLODED VIEW OF CONTOL PANEL & DISPENSE ASSY B-24 B- B-2 B-2 B-4 B-5 B-6 B-7 B-9 B-22 B-8 B-25 B-8 B-0 B- B-2 B-3 B-7 B-4 B-5 B-6 37

32 ÆTHE PATS LIST OF CONTOL PANEL & DISPENSE ASSY L/No. PAT NAME PAT. SVC COD Q flty SPEC B- B-2 B-4 SCEW, MACHINE PAN HEAD VALVE HOSE ASSY, INLET SCPF F3067A 5220F25A 524FA46 525FD VAC VAC (SEMKO) VDE(IMQ) 3W4002 VDE(IMQ) B-5 B-6 B-7 B-8 B-0 B- B-2 B-3 B-4 B-5 B-6 B-7 B-8 HOSE CONNECTO (MECH), DAIN HOSE SCEW, TAPPING TUSS HEAD HOSE ASSY, DAIN CLAMP CLAMP BELLOWS ING, SNAP SCEW PWB ASSY(DISPLAY) PANEL ASSY, CONTOL WD-223F(H)/WD-225F(H) WD-243F(H)/WD-245F(H) SCEW, TAPPING TUSS HEAD LEAD WIE ASSY 524F425B 4932F356A TTG F388A 486F3068C 4860F3092D 4738F2065A 3W W532A 687FC2272D 372E F96 TTL E002A 6877E002B 2 9 MAIN MAIN(Hot) 6877E92B MOTO~PWB 6877FC226B DISPLAY~PWB B-9 B-2 PANEL ASSY, DAWE DISPENSE ASSY WD-223F(H)/WD-225F(H) WD-243F(H)/WD-245F(H) 372E00 372F F37F 4925F37G HEATING B-22 B-24 B-25 DAIN HOSE HANGE VALVE HOSE, PUMP 3W5072A 5220F280A 524F388A VAC (HEATING) 38

33 0-3 THE EXPLODED VIEW OF DUM & TUB ASSY C-42 C-43 C-49 C-44 C- C-45 C-4 C-46 C-40 C-39 C-38 C-2 C-37 C-3 C-36 C-35 C-47 C-34 C-6 C-4 C-5 C-7 C-9 C-26 C-25 C-24 C-27 C-3 C-0 C-8 C- C-2 C-4 C-3 C-5 C-23 C-22 C-2 C-20 C-9 C-8 C-6 C-7 39

34 ÆTHE PAT LIST OF DUM & TUB ASSY L/No. PAT NAME PAT. SVC COD Q flty SPEC C- BOLT ASSY 40F373A C-2 BELT, POLY-V 4400F36A C-3 PULLEY 4560F49A C-4 TUB ASSY 3045F003C C-5 BACKET 480F467A C-6 SPING 4970F2084F C-7 SCEW SZZFA4362A 2 C-8 SCEW SZZF474A 2 C-9 BACKET, MOTO 480F97A C-0 SCEW SZZFA4362A 4 C- MOTO ASSY 468F24B VDC C-2 DAMPE ASSY 490F2080A 2 C-3 HINGE 4774F38A 4 C-4 BOLT ASSY 40F373B 3 C-5 WEIGHT, BALANCE LOWE 4844F283A C-6 CLAMP 4860F3092C C-7 HOSE(SENSO) 524F425J C-8 CHAMBE, AI 3504F334A C-9 CLAMP, HOSE 486F3068C 3 C-20 BELLOWS 4738F45A C-2 CLAMP, HOSE 486F3068E C-22 HOUSING ASSY (MECH), PUMP 366F2093 C-23 SCEW, TAPPING TUSS HEAD TTL C-24 POTECTO (MECH) 3740F3043A C-25 SCEW, TAPPING TUSS HEAD TTL C-26 HEATE ASSY 530F58A 220VAC2500W 530F58B 240VAC2000W 530F58C 220VAC2000W 530F58D 230VAC2000W 40

35 L/No. PAT NAME PAT. SVC COD Q flty SPEC C-27 THEMISTO 6322F2046B C-3 UBBE 5040F468B 4 C-34 GASKET 4987F65B C-35 COVE, TUB 3044F0027A C-36 SCEW, TAPPING TUSS HEAD TTL C-37 SEAL 4036F423A C-38 CLAMP, TUB 4860F424A C-39 TUB, DUM ASSY 3044F220 C-40 SPING 4970F2084E 2 C-4 HOLDE(SPING) 4930F3040A 3 C-42 WEIGHT, BALANCE UPPE 4844F223A C-43 SCEW SZZFA4362A 6 C-44 BACKET IGHT 480F466A C-45 SCEW TTL C-46 BACKET UPPE LEFT 480F426A 2 C-47 TUB GASKET CLAMP ASSY 486E200A C-49 BACKET UPPE IGHT 480F426B C-50 SCEW 4W532A 3 4

36 ÆAPPENDIX(The type of power cord) TYPE TYPE OF PLUG POWE COD P/No. A A B B-2 2A 2 PIN 3.5 E PIN 5 5A 2 PIN 5 EPIN 7 5A 2 PIN 7 E PIN B-3 64F69F B F69E 25.6 C

37 TYPE TYPE OF PLUG C-2- C-3-2 C-2-2 C-4-2 C-5 C-3- S POWE COD P/No F69B 64F69N 64FD096V 64F69D 64F69P 64F69Q