MODEL V5160MUX 16-CHANNEL DIGITAL COLOR MULTIPLEXER

Transcription

1 XX084 MODEL V5160MUX 16-CHANNEL DIGITAL COLOR MULTIPLEXER Copyright 2001 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo are registered trademarks of Vicon Industries Inc. VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK TEL: CCTV (2288) FAX: CCTV (2288) TOLL FREE: Hour Technical Support: VICON ( ) UK: 44/(0) INFOFAX: WEB: Vicon part number Rev 801 Section 5

2

3

4 FCC Notice Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a Class A digital device. WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer s instruction, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class A computing device in accordance with the specification in subpart B of part 15 of the FCC rules, which are designed to provide reasonable protection against such interference in a commercial installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: Reorient the receiving antenna. Relocate the equipment with respect to the receiver. Relocate the equipment away from the receiver. Plug the equipment into a different electrical outlet so that the equipment and receiver are on different branch circuits. If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may find the following booklet prepared by the Federal Communications Commission helpful: Interference Handbook, Bulletin CIB-2 This booklet is available from the U.S. Government Printing Office, Superintendent of Documents, Mailstop SSOP, Washington, D.C , ISBN Warning: Power must be removed from this unit before removing circuit modules or ribbon cables. Caution: This unit contains circuit cards with integrated circuit devices that can be damaged by static discharge. Take all necessary precautions to prevent static discharge

5 Important Safeguards 5. Cleaning - Step a applies to equipment that can be disconnected from the CCTV system without seriously jeopardizing security. Step b applies to equipment that must operate continuously such as video switching equipment at military installations. a. Disconnect this video product from its power source before cleaning. Do not use caustic, abrasive, or aerosol cleaners. Use a damp cloth for cleaning. b. Use a damp cloth to clean the equipment. Do not allow moisture or liquids to enter any vents. Do not use caustic, abrasive, or aerosol cleaners. 6. Attachments - Do not use attachments not recommended by Vicon as they may cause hazards. GRAPHIC SYMBOL EXPLANATION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit. 1. Read Instructions - All the safety and operating instructions should be read before the video product is operated. 2. Retain Instructions - All the safety and operating instructions should be retained for future reference. 7. Water and Moisture - Do not use this video product in any location where it may be exposed to water or moisture. This does not apply to outdoor camera housings, outdoor panand-tilt drives, and other equipment designed for direct exposure to outdoor environments. 8. Accessories - Do not place this video product on any unstable surface or table. The video product may fall, causing serious injury to a person and serious damage to the video product. Use only with a mounting accessory recommended by Vicon, or sold with the video product. Any mounting of the video product should follow Vicon s instructions, and a mounting accessory recommended by Vicon should be used. 9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the video product on a rug or other similar surface. This video product should never be placed near or over a radiator or heat register. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or Vicon s instructions have been adhered to. 10. Power Sources - This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your installation site, consult your Vicon dealer or local power company. For video products intended to operate from battery power, or other sources, refer to the operating instructions. 3. Heed Warnings - All warnings on the video product and in the operating instructions should be adhered to. 4. Follow Instructions - All operating and use instructions should be followed.

6 11. Grounding - This applies to video products equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug only fits into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 12. Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the video product. 13. Outdoor Cable Grounding - If an outside cable system is connected to the video product, be sure the cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA , provides information with respect to proper grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. 14. Lightning - For added protection for this video product when it is not used for long periods of time, disconnect it from its power source and from the cable system. This prevents damage to the video product due to lightning and power-line surges. 15. Power Lines - An outside cable system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside cable system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Servicing - Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 19. Damage Requiring Service - Disconnect this video product from its power source and refer servicing to qualified service personnel under the following conditions. Note that step c does not apply to outdoor camera housings, outdoor pan-and-tilt drives and other equipment specifically designed for direct exposure to outdoor environments. a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. e. If the video product has been dropped or the cabinet has been damaged. f. When the video product exhibits a distinct change in performance - this indicates a need for service. 20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by Vicon or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 21. Safety Check - Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition. 17. Object and Liquid Entry - Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.

7

8 CONTENTS Important Safeguards 1. Unpacking Service Description Installation Connections Programming Time/Date Date Format Date Set Time Format Time Set Camera Titles Dwell Setup Alarm Setup Alarm Titles Alarm Attribute Setup VD Loss Alarm Setup Dwell Time Setup Buzzer Out Relay Out Trig Out Record Setup Field Delay Setup Record Mode Setup Alarm Record Setup Alarm Speed Setup VCR Input Setup Zone Setup Holiday Setup Record Time Setup Display Setup Spot Monitor Setup Spot Dwell Setup Time and Title Display Display Position Event Log System Setup Communication Setup Password Setup Factory Default Setting Operation Video Trigger Operation Mode Computer Remote Control Maintenance. 15 Shipping Instructions.. 16

9 1. Unpacking Unpack carefully. This is electronic equipment and should be handled carefully. Check to ensure that the following items are included for applicable models are ordered. V5160MUX 16-Channel Digital Color Multiplexer Accessory Pack including 12 VDC Adapter. Installation instructions. 2. Service If the unit ever needs repair service, the customer should refer to the Shipping Instructions at the end of this manual. This unit should be installed by a qualified technician using approved materials. Read these instructions through completely before attempting installation. 3. Description The V5160MUX Digital Color Multiplexer provides on-screen display of sixteen camera inputs combined with numerous additional functions. The image display is updated at the field rate of 60 field/sec. In addition to multi - screen displays or playback on a single monitor, multiplex recording on a VCR of up to 16 camera images is possible with this duplex multiplexer as well. Note : 1. If the video is to be looped out to other equipment, make sure that the final item of video equipment on each line is terminated with 75 ohms. 2. The time lapse VCR can be connected to the unit to allow to response to alarms. 3. Do not apply any voltage to any alarm input. It will damage the unit. 4. The V5160MUX does not echo received characters. 2

10 4. Installation 4.1 Connections camera 16 DC 12V camera 2 Power Adapter camera 1 Looping (Automatic Termination) Alarm In Alarm Out RS232 Connector AC-IN RS485 Connector In Out Trig In/Out 5. Programming Spot Monitor Output Monitor Output Time Lapse VCR Table 1 Key Functions Key label Operating Function Programming Function Selects to display or delete Title on monitor TITLE (latching). NONE VCR Selects VCR input to display on monitor. Selects Title and VCR to display the recording status on monitor. NONE Selects the alarming mode and alarm reset ALARM function. NONE MENU Selects the programming mode. Selects entries. FREEZE/ Selects the freeze mode display on monitor. Increases the programmed value on menu screen. ZOOM/- Selects the zoom mode display on monitor. Decreases the programmed value on menu screen. NONE Scrolls upwards through program selections; selects entries. SPOT/ Sets the Spot monitor (analog screen). Scrolls downwards through program selections; selects entries. SEQ/ Selects the sequential switching function. Shifts cursor to the left in menu; selects entries. CHANGE/ In multi-picture mode, allows the reassignment of another camera in the same group to the selected Shifts cursor to the right in menu; selects entries. window. SHIFT/ENTER See SHIFT+KEY below Moves to the sub-menu. Numeric (1-16) SHIFT+KEY 1,2,3,4,5,6,7,8,9, Programming 10, 11,12,13 Functions monitor. Programming Functions Selects the designated camera; displays the full screen in normal mode or VCR mode. Selects quad screens, 6-screen, 8-screen, 7-screen, 9-screen, 10-screen, 13-screen, 16-screen on 3 NONE NONE

11 All programming is done with the front panel keys. There are 21 keys on the front panel. The keys named MENU, FREEZE/+, ZOOM/-,, SPOT/, SEQ/, CHANGE/, and SHIFT/ENTER are used in programming unit. The TITLE, VCR, and ALARM keys are not used in programming the unit. Functions of each key on the front panel are described in Table 1. Scrolls upward through program selections; selects entries. Scrolls downward through program selections; selects entries. ENTER enters or sets function. Press the MENU key to display the programming screen. The following is displayed: MAIN MENU (1) TIME/DATE (2) CAMERA TITLES (3) DWELL SETUP (4) ALARM SETUP (5) RECORD SETUP (6) DISPLAY SETUP (7) SPOT MONITOR SETUP (8) EVENT LOG (9) SYSTEM SETUP 5.1 Time/Date This menu allows you to setup the time and date of the video display and multi-screen. Select TIME/DATE and press the ENTER key. The following menu is displayed: TIME /DATE DATE FORMAT : MM/DD/YEAR DATE SET : TIME FORMAT : 12 HOURS TIME SET : PM 03:47: Date Format Press the (+) and (-) keys to toggle between the formats. The options are: MM/DD/YEAR DD/MM/YEAR YEAR/MM/DD (YEAR: 2000 ~ 2099) Press the MENU key to exit the menu Date Set Press the (+) and (-) key to establish the necessary digit Press the and keys to move the cursor to the required position. Press the MENU key to exit the menu Time Format P ress the (+) and (-) keys to toggle to select the required format. The options are: 12 HOURS 24 HOURS Press the MENU key to exit the menu. 4

12 5.1.4 Time Set Press the (+) and (-) key to establish the necessary digit. Press the and keys to move the cursor to required position. Press the MENU key to exit the menu. 5.2 Camera Titles Select CAMERA TITLES screen and press the ENTER key. The following menu is displayed: CAMERA TITLES CAMERA 01 = CH01 CAMERA 02 = CH02 CAMERA 03 = CH03 CAMERA 16 = CH16 Press the and keys to move the cursor to required camera. Press and to highlight the character. Select the camera title, using the (+) and (-) keys to select the desired character up to a max. 7 characters. Choose from the following for each of the characters: Alphabet (26 letters), Number (0~9), Special Characters ( [.],[,],[:],[+],[-],[*],[/],[(),[]],[?],[ ]). Press the MENU key to exit the menu. Note: To retain all titling (camera and alarm), the tape must be played back on the same V5160MUX it was recorded on. 5.3 Dwell Setup This menu allows you to adjust the dwell times of the 16 camera video displays. Select DWELL SETUP and press the ENTER key. The following menu is displayed: DWELL SETUP CAMERA 01 = 5SEC CAMERA 02 = 5SEC CAMERA 03 = 5SEC CAMERA 16 = 5SEC SPLIT 4X4 = 5SEC Press the and keys to move the cursor to required camera. Press the (+) or (-) key to adjust the dwell time. Dwell times may be programmed from SKIP to 99 seconds. A setting of SKIP removes the channel from the sequence. Press the MENU key to exit the menu. 5.4 Alarm Setup The ALARM SETUP menu allows you to set the alarm options for each of the video inputs. The alarm can be set for titling on or off, dwell time, polarity and video loss. The unit can also have the audio beeper set to on or off. Select ALARM SETUP and press the ENTER key. The following menu is displayed: 5

13 ALARM SETUP (1) ALARM TITLES (2) ALARM ATTRIBUTE SETUP (3) VD LOSS ALARM SETUP (4) DWELL TIME = 60 SEC (5) BUZZER OUT = ON (6) RELAY OUT = ON (7) TRIG OUT = LOW Alarm Titles You can select an Alarm title for each channel. Select ALARM TITLES and press the ENTER key. The following menu is displayed: ALARM TITLES CAMERA 01 = ALARM 01 CAMERA 02 = ALARM 02 CAMERA 03 = ALARM 03 CAMERA 16 = ALARM 16 Press the and keys to move the cursor to the required alarm number. Press the and keys to move the cursor to the required character position. Select the camera title, using the (+) and (-) keys to select the character up to a max. 7 characters. Choose from the following for each of the characters: Alphabet (26 letters), Number (0~9), Special Characters ([.],[,],[:],[+],[-],[*],[/],[(),[]],[?],[ ]). Press the MENU key to exit the menu Alarm Attribute Setup The ALARM ON/OFF function enables you set the alarm on or off for each video channel. ALARM POLARITY function enables you to define how the alarm is generated for each alarm input, either normally open (NO) or normally closed (NC) contacts. Select ALARM ATTRIBUTE SETUP and press the ENTER key. The following menu is displayed: ALARM ATTRIBUTE SETUP ON/OFF POLARITY ALARM 01 = ON ALARM 02 = ON NO NO ALARM 16 = ON NO Press the or key to move the cursor to the required alarm number. Press the and key to select between ON/OFF and POLARITY. Press the (+) and (-) keys to toggle NO or NC and ON or OFF. 6

14 5.4.3 VD Loss Alarm Setup The VIDEO LOSS ALARM function enables you to define if an alarm is generated when any of the video inputs is lost/not detected. Select VD LOSS ALARM SETUP and press the ENTER key. The following menu is displayed: VD LOSS ALARM SETUP CAMERA 01 = ON CAMERA 16 = ON Press the or key to move the cursor to the required camera. Press the (+) and (-) keys to toggle ON or OFF Dwell Time Setup The DWELL TIME function allows you to set the automatic reset period after an alarm is generated. Select DWELL TIME on ALARM SETUP menu. The time is highlighted. Press the (+) or (-) key to adjust the time. The options are: 1-99 SEC: automatic reset period HOLD: alarm continues until the alarm camera key is pressed followed by the ALARM key FOLLOW: alarm continues during the period of input and will go off automatically Buzzer Out The BUZZER OUT function allows you to enable or disable an audible alarm. Select BUZZER OUT on the ALARM SETUP screen. ON or OFF is highlighted. Press the (+) and (-) key to toggle ON or OFF Relay Out The RELAY OUT function allows you to turn the relay out ON or OFF to respond to an alarm or video loss. Select RELAY OUT from the ALARM SETUP screen. ON or OFF is highlighted. Press the (+) and (-) key to toggle ON or OFF Trig Out The TRIG OUT function respo nds to an alarm input. The unit allows you to turn the TTL (standard 5V level) level HIGH or LOW (TRIG OUT does not respond to video loss). Select TRIG OUT from the ALARM SETUP screen. HIGH or LOW is highlighted. Press the (+) and (-) key to toggle HIGH or LOW. Note: The TRIG OUT is tied to the VCR alarm input. The signals (HIGH or LOW) must match the signals on the equipment (i.e., VCR) it is hooked up to. 5.5 Record Setup The RECORD SETUP defines how the unit s video output to the time lapse VCR is recorded. Select RECORD SETUP and press the ENTER key. The following menu is displayed: 7

15 RECORD SETUP (1) FIELD DELAY : 002 FIELD (2) REC MODE : FRAME REC(R/T) (3) ALM REC : NO CHANGE (4) ALM SPEED : FOLLOW (5) VCR INPUT : CVBS (6) ZONE SETUP (7) HOLIDAY SETUP (8) RECORD CAMERA SETUP Field Delay Setup Select FIELD DELAY from the RECORD SETUP screen. The option is highlighted. Press the (+) and (-) key to toggle the options. The options are: VEXT USED : Record mode must be set to time lapse for VEXT to work 002 ~ 511 FIELD : This selects the field when the VCR snaps the picture; it must be set to the clock in the VCR and might require some trial and error to set correctly (check the VCR manual) Record Mode Setup Select REC MODE to set the type of recording. The option is highlighted. Press (+) and (-) keys to toggle the options. The options are: TIME LAPSE FRAME REC (R/T) FIELD REC (R/T) REC OFF Alarm Record Setup Select ALM REC to decide the recording condition when an alarm is occurred. Press (+) and (-) keys to toggle the options. The options are: NO CHANGE: Alarm recording remains as set on the REC MODE (time lapse or real time). EXCLUSIVE: Only alarmed camera records. INTERLEAVE: Alarm camera is interleaved into the pattern more often Alarm Speed Setup Select ALM SPEED to decide the speed of alarm when an alarm is occurred. Press (+) and (-) keys to toggle the options. The options are: FOLLOW: Recording in mode selected in REC MODE menu. If in VEXT mode, uses clock in VCR to set record speed. FRAME REC (R/T): Recording in frame with real time speed. FIELD REC (R/T): Recording in field with real time speed. 002 ~ 361 FIELD: Select a time delay for the time lapse recording VCR Input Setup Select VCR INPUT on the RECORD SETUP menu to choose if the recording and playback are to be made through CVBS (Composite Video) or Y/C (S-VHS). Press the (+) and (-) keys to toggle CVBS or Y/C. 8

16 5.5.6 Zone Setup Select ZONE SETUP to set the recording time zone of each channel. Press ENTER key. The following menu is displayed. ZONE SETUP REC ZONE A = 10:00 13:00 REC ZONE B = 14:00 19:00 REC ZONE C = 11:00 18:00 REC ZONE D = 20:00 06:00 DEFINE C, D = SUN + SAT + HDAY *ZONE A, B MEANS WEEKDAY *ZONE C, D MEANS WEEKEND Select the zone to be programmed. Press the (+) and (-) keys to select time; press the to select the time range (from/to). Set the recording time range of the cameras in ZONE A as weekday period. Set the recording time range of the cameras in ZONE B as weekday period. Set the recording time range of the cameras in ZONE C as weekend period. Set the recording time range of the cameras in ZONE D as weekend period. ZONE A, B are for the weekday ZONE C, D are for the weekend, including Sunday, Saturday and Holiday, Sunday and Holiday, Sunday, Sunday and Saturday, Holiday, and same as Zone A, B. Holidays can be addressed separately in the following menu Holiday Setup Select HOLIDAY SETUP to designate holidays to be recognized as weekend for the recording option. Press ENTER key. The following screen is displayed. HOLIDAY SETUP MM-DD MM-DD MM-DD MM-DD (1) INSERT (2) DELETE Select INSERT and set the required date by pressing (+) and (-) keys. Press to select month or day. Press the ENTER key to add the holiday. To remove a certain date from the list, move the cursor to the DELETE; the listed holiday will appear from the earliest date. Press the ENTER key to delete that date; then the following date will then appear Record Camera Setup Select the RECORD CAMERA SETUP to decide the record time zone of each camera channel. Press the ENTER key. The following screen is displayed. 9

17 RECORD CAMERA SETUP WEEKDAY WEEKEND CAMERA 01 = ALWAYS ALWAYS CAMERA 02 = ALWAYS ALWAYS CAMERA 03 = ALWAYS ALWAYS CAMERA 16 = ALWAYS ALWAYS Press the and key to select camera number. Press the and key to select weekday or weekend. Press (+) and (-) keys to select options: Options for WEEKDAY are : ALWAYS, ZONE A,B, ZONE A, ZONE B, SKIP Options for WEEKEND are : ALWAYS, ZONE C,D, ZONE C, ZONE D, SKIP *ALWAYS: Records all the time. *ZONE: Recording only possible during the times designated in ZONE A, B, C, D. *SKIP: Do not record. 5.6 Display Setup Programming the display mode includes all formats for display on monitor. Select DISPLAY SETUP on MAIN MENU. Press the ENTER key. The following menu is displayed: DISPLAY SETUP TIME : OFF BY <TITLE> KEY TITLE : OFF BY <TITLE> KEY POSITION : BOTTOM BORDER LINE : WHITE SCREEN COLOR : BLUE Select TIME or TITLE using the or keys. The option is highlighted. Press the (+) and (-) keys to toggle the options. The options are: OFF BY <TITLE> KEY: Will not display time/title while TITLE key is pressed. OFF ALWAYS: Time/Title never displays. ON BY <TITLE> KEY: Displays the characters of time/title while TITLE key is pressed. ON ALWAYS: Time/Title always displays. Select POSITION to set the display position of time and title. Press the (+) or (-) key to toggle BOTTOM or TOP. Select BORDER LINE to set the color of the border line of split screens. Press the (+) or (-) key to toggle options. The options are: WHITE, GRAY, BLACK, NONE Select SCREEN COLOR to choose the background color of the screen. Press the (+) or (-) key to toggle options. The options are: BLUE, BLACK If using a monochrome monitor you must select BLACK. 10

18 5.7 Spot Monitor Setup Select SPOT MONITOR SETUP on MAIN MENU. Press the ENTER key. The following will be displayed: SPOT MONITOR SETUP (1) DWELL SETUP (2) TIME DISPLAY : ON (3) TITLE DISPLAY : ON (4) DISPLAY POSIT : BOTTOM Spot Dwell Setup Select DWELL SETUP from the SPOT MONITOR SETUP screen. The following is displayed: SPOT DWELL SETUP CAMERA 01 = 5 SEC CAMERA 02 = 5 SEC CAMERA 03 = 5 SEC CAMERA 16 = 5 SEC Press the or keys to select the camera number. Press the (+) and (-) keys to select the number of seconds (1~99 or SKIP). Press the MENU to exit screen Time and Title Display Select TIME DISPLAY or TITLE DISPLAY from the SPOT MONITOR SETUP screen. The option is highlighted. Press the (+) and (-) keys to toggle ON or OFF. Press the MENU to exit screen Display Position Select DISPLAY POSITION on the SPOT MONITOR SETUP screen. The option is highlighted. Press the (+) and (-) keys to toggle TOP or BOTTOM. Press the MENU to exit screen. 5.8 Event Log The multiplexer keeps a record of the events, up to 450 events, by Power On, Video Loss, Alarm Occur, Alarm Reset, Programming, All Clear and Factory Setting. Program event is only recorded when the contents are changed. If the events in the log is full with 450 events, recording will be stopped and an EVENT FULL message appears until the events in the log are deleted. Select EVENT LOG from the MAIN MENU. Press the ENTER key. The event lot screen displays. To delete all the entire list in the event log, press the TITLE and VCR keys simultaneously. 11

19 EVENT LOG 168: :47:23 P-ON 169: :52:45 C9 V/L 170: :10:10 ALM RS 171: :25:30 C8 V/L 172: :40:55 PGM 173: :10:11 ALM RS 174: :15:30 PGM *P-ON: Power On *C N V/L: Channel N Video Loss ( ex. C9 V/L: Ch.9 Video Loss) *ALM RS: Alarm Reset *C N ALM: Channel N Alarm (ex. C4 ALM: Ch.4 Alarm) *PGM: Programming *A-CLR: All Clear *F-SET: Factory Setting 5.9 System Setup Select SYSTEM SETUP on the MAIN MENU. The following menu is displayed: SYSTEM SETUP (1) COMMUNICATION SETUP (2) PASSWORD SETUP Communication Setup Select COMMUNICATION SETUP on the SYSTEM SETUP menu and press the ENTER key to choose the communication speed. The options of BAUD RATE are: 1200 bps, 2400 bps, 4800 bps, 9600 bps,19600 bps, bps COMMUNICATION SETUP BAUD RATE : 1200BPS UNIT ADDRESS : 00 COMMUNICATION: RS-232 Select UNIT ADDRESS to designate the address of the unit by pressing (+) or (-) key. The addresses available are from 00 ~ 99 (only for RS-485). Select COMMUNICATION to choose the communication method. The options are: RS-232 RS-485 (not available) Press the MENU key to exit the screen. 12

20 5.9.2 Password Setup Select PASSWORD SETUP on the SYSTEM SETUP menu and press (+) or (-) key to toggle the options: DISABLE, ENABLE PASSWORD SETUP PASSWORD : DISABLE NEW PASSWORD: To enable a password, select ENABLE. Select NEW PASSWORD and press the ENTER key. Confirm password. Press the MENU key to exit programming screen. When the Password is forgotten, turn off the unit, press and hold TITLE key and turn the unit on again; the unit will now have a factory default settings Factory Default Setting To return to the factory default setting, turn the unit off, press and hold the TITLE key and then turn the unit on again. 6. Operation Front panel LEDs light to indicate video inputs. Any channel without a video input is automatically skipped during sequencing. Refer to Table 1 for operation keys. In VCR playback, if no video was recorded, if a camera was not in the schedule to be recorded, or if there was video loss, the word Mask appears on the screen. Record check function in VCR mode Press the VCR button to check the recording screen in VCR mode. Press VCR again to exit VCR mode. Press the SEQ button to change to full screen sequencing. Full Real -Time Display in Multi-Screen mode Various multi-screen displays are available with full real-time displays in different split screen mode. Press Shift with numeric key to call each split mode. Use CHANGE key to select a window in the split screen and press a numeric key to insert that camera into the selected window. Group A (ch1~ch8 display for splits less than 9 displays) Shift Key + Numeric 1 : Quad display Shift Key + Numeric 2 : 6 screen display Shift Key + Numeric 3 : 8 screen display Shift Key + Numeric 4 : 7 screen display Shift Key + Numeric 5 : 9 screen display Shift Key + Numeric 6 : 10 screen display Shift Key + Numeric 7 : 13 screen display Shift Key + Numeric 8 : 16 screen display Group B (ch9 ~ch16 display for splits less than 9 displays) Shift Key + Numeric 9 : Quad display Shift Key + Numeric 10 : 6 screen display 13

21 Shift Key + Numeric 11 : 8 screen display Shift Key + Numeric 12 : 7 screen display Shift Key + Numeric 13 : 9 screen display Shift +1 Shift +2 Shift +3 Shift +4 Shift +5 Shift +6 Shift +7 Shift +8 Shift +9 Shift +10 Shift +11 Shift +12 Shift Video Trigger Operation Mode Recording begins when a video trigger signal is raised by a VEXT (clock) input signal in time-lapse VCR operation mode. Performance in this mode is better at capturing the picture than operation without this signal because there is less error rate. To use the trigger operation mode, TRIG OUT must be set to LOW and REC MODE must be set to TIME LAPSE. This setting does not recognize Video Loss as an alarm condition. REC OUT Trigger Operation Mode When an alarm occurs, this signals the VCR to record. Trigger connection on rear panel of V5160MUX: Alarm In / Out Pin No. Signal Pin No. Signal 1 Alarm 16 in 14 Alarm 3 in 2 Alarm 15 in 15 Alarm 2 in 3 Alarm 14 in 16 Alarm 1 in 4 Alarm 13 in 17 NO 5 Alarm 12 in 18 COM 6 Alarm 11 in 19 NC 7 Alarm 10 in 20 GND 8 Alarm 9 in 21 GND 9 Alarm 8 in 22 GND 10 Alarm 7 in 23 GND 11 Alarm 6 in 24 GND 12 Alarm 5 in 25 GND 13 Alarm 4 in Trig In/Out Pin No. Signal 1 Trigger In (VEXT/VCR Clock Out) 2 GND 3 Trig Out (TTL to VCR to VCR Alarm Input) 14

22 7.1 Computer Remote Control The V5160MUX uses a very simple command set, each command consisting of three characters. The first character in all cases is the slash or virgule (/). The unit looks only for a three -character command, with an initial slash. It ignores all other characters. If a mistake is made in entering a command, just type in another slash character followed by the appropriate character for the desired command. The commands are listed in the Table 2, RS-232 Commands. Signal Format is as follows: 1. Data Format: 1,200 Baud (Selectable)/ 8 Data Bit/No Parity/ One Stop Bit. 2. Mode: Half Duplex Mode (Not Echo Received Character). RS-232 Pinout Pin 1 Pin 2 Pin 3-4 Pin 5 Pin 6-9 Not Used RS-232 In Not Used GND Not Used RS-232 Commands COMMAND RS-232 CODE Title /TI Numeric 01 /01 VCR /VR Numeric 02 /02 Rec View /RV Numeric 03 /03 Alarm /AM Numeric 04 /04 Menu /MU Numeric 05 /05 FRZ /FR Numeric 06 /06 Zoom /ZO Numeric 07 /07 Up /UP Numeric 08 /08 Down /DN Numeric 09 /09 Left /LF Numeric 10 /10 Right /RG Numeric 11 /11 Plus /PL Numeric 12 /12 Spot /SP Numeric 13 /13 Minus /MI Numeric 14 /14 SEQ /SQ Numeric 15 /15 Change /CN Numeric 16 /16 Enter /ET Shift /SF 8. Maintenance The V5160MUX Multiplexer unit requires no routine maintenance and is designed for long, trouble-free use under normal operating conditions. Repair should only be attempted by qualified personnel. 15

23 Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. Vicon Industries Inc. 89 Arkay Drive Hauppauge, NY Phone: CCTV (2288); Toll-Free: ; Fax: CCTV (2288) For service or returns from countries in Europe, contact: Vicon Industries Ltd Brunel Way Fareham, PO15 5TX United Kingdom Phone: 44/(0)1489/566300; Fax: 44/(0)1489/ Attach a sheet of paper to the unit with the following information: a. Name and address of the company returning the unit b. Name of the Vicon employee who issued the R.A. c. R. A. number d. Brief description of the installation e. Complete description of the problem and circumstances under which it occurs f. Unit s original date of purchase, if still under warranty 3. Pack the unit carefully. Use the original shipping carton or its equivalent for maximum protection. 4. Mark the R.A. number on the outside of the carton on the shipping label. 17

24 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York CCTV (2288) Fax: CCTV (2288)!Infofax: Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) Fax: +44 (0) Brussels Office Planet II - Unit E Leuvensesteenweg 542 B-1930 Zaventem Belgium +32 (2) Fax: +32 (2) Far East Office Unit 5, 17/F, Metropole Square 2 On Yiu Street, Shatin New Territories, Hong Kong (852) Fax: (852) Internet Address: