N9 Smart Driveway Alarm User Manual

Transcription

1 N9 Smart Driveway Alarm User Manual

2 Table of Contents: Chapter 1 Introduc on... Chapter 2 Product Features... Chapter 3 Product Diagram Sensor Overview How to Powering Your Sensor Receiver Overview... Chapter 4 APP Opera on&monitoring Register Account Wi-Fi Configura on APP Func on Introduc on Sensor Se ng Zone Se ng Add or Delete sensors Se ng Bu on Installing your Sensor Adjus ng Sensor Field of View Chapter 5 Low Ba ery Indica on Chapter 6 Factory Reset Chapter 7 LED Indicator Chapter 8 Total Clear Chapter 9 Specifica on... Chapter 10 Alexa Control

3 Chapter 1 Introduc on Thanks for purchasing BIBENE N9 WIFI Smart Driveway Alarm. Please read this user manual carefully before use, we will update this manual on a regular basis in accordance with the addi on or upgrade of the product features. If you need any assistance, please contact our support team, we will contact you within 24 hours. Customer Service Address: lhxing@hotmail.com Moun ng Plate Ball-joint Adjustment Screw Sensor Eye Field-of-view Adjustment Cover Chapter 2 Product Features The N9 WIFI Smart Driveway Alarm uses a Passive Infra-Red (PIR) Mo on Sensor to detect movement of people and vehicles. The Base Sta on is powered by the DC adapter or USB cable and 3 AA ba eries to supply power in case of a power outage. Aler ng You When Visitors Enter Your Driveway Deterring Trespassers and Thieves from Entering Your Property or Building Aler ng You to Wildlife on Your Land Using in Drive-Thrus to Signal that a Customer Has Pulled in, and More! NOTE: The Base Sta on is intended for indoor use ONLY. Chapter 3 Product Diagram 3.1 Sensor Overview You can pair up to 12 sensors to your receiver (2 Per Zone). Each zone can have its own unique reminder melody. 2 Distance Sensi vity Switch An -dismantle Switch SWITCH#1 OFF ON SWITCH#2 OFF ON SWITCH#3 An -Break Bu 6m Detec on Range 12 Detec on Range (Default) LED Indicator OFF LED Indicator ON (Default) on Ba ery Compartment (2 AA Ba eries) LED Indicator Switch OFF ON 3

4 3.2 How to Powering Your Sensor The sensor runs on 2 AA ba eries, and operates wirelessly at a maximum distance from the receiver of 1050 (350m). To insert ba eries into the remote sensor: 1.Remove the holder on the back of the sensor and then unscrew the sensor to access the ba ery compartment. (Be careful the screws are very small, don't lose them.) 2.Install 2 AA ba eries, replace the cover and secure the screws. LED Indicator Volume Up/Down Music Audi on Se ng Charging Port Ba ery Compartment Chapter 4 APP Opera on&monitoring 4.1 Scan the QR code, or search "N9" in the APP Store or Google Play to download and install the APP. 3.3 Receiver Overview The receiver has SIX zones that you can use to cover a variety of loca ons. You can also have mul ple receivers in different loca ons in your home or business, so you can hear the alarm chimes. IOS Android/Google Play 4 5

5 Warm Tips: Tap "Allow" to allow receiving no fica on from "N9" Please Note: As registra on doesn't need to enter the verifica on code, please make sure that the address is correct. Users can find and set the new password through the when forget password.) Wi-Fi Configura on Register Account Register one account if you are first to use the app. Type into E m a i l a n d p a s s word,t h e n c l i c k " C o n fi r m ", re g i ster finished.you can share your login account with your family members. Step 1: Connect N9 receiver with power socket, the panel will be powered on automa cally and beep once. Then LED light will flash purple and cyan indicates that the wai ng for configuring. 5V/1A Step2: Make sure that your smart phone is connected to your WIFI network on the whole me. Please Note: N9 doesn't support WIFI of 5Ghz band. If you use dual-band (5Ghz and 2.4Ghz) router, please make sure to connect this system with the 2.4Ghz instead of the 5Ghz. 6 7

6 Step3: A er account registra on, enter into device list, click "+" to choose "N9" device, there are T W O network connec ng modes, W I-F I Configura on Mode and A P Connec on Mode. A.WI-FI Configura on Mode 1.Click "NEXT STEP" to go to Network Configura on Mode page. 2.Long press Volume key on the receiver, the LED will flash blue and emit W I F I configuring, please enter W I F I password in the APP. 3.Then click N E X T STEP on the A P P to enter W I F I password. APP will start the 60 seconds of countdown to configure. 4.The LED of receiver will flash in cyan 5 mes means successfully configured. 5.The device will under LAN UNBOUND DEVICE, shows NOT BOUND. 6.Click the device to bind the device and the device will under ONLINE DEVICE. 8 9

7 B. AP Connec on Mode 1.Click "NEXT STEP" to go to AP Connec on Mode. 2.Enter the WI-FI password of your network, then click next step. 3.Long press Volume and LED key on the receiver, the LED will flash green and emit WIFI configuring, please enter WIFI password on the APP. 4.Then click Set up on the APP to find out the WIFI of the receiver, usually named as XPG-GAgent-xx. Then enter the W I F I password of the receiver, default password is A er connected to receiver, click to return to the APP, the LED of receiver will flash in cyan 5 mes means successfully configured. 6.The device will under LAN UNBOUND DEVICE, shows NOT BOUND. 7.Click the device to bind the device and the device will under ONLINE DEVICE. 10 Please Note: AP connec on mode was used to judge whether this system fits your router. If it cannot return to the APP control page, this system may not fits your router, please contact us to return it. 11

8 4.2 APP Func on Introduc on Click the ONLINE DEVICE to enter the control page for more opera on. Volume WIFI Device Click to tune the volume Check the strength of the WIFI signal Device informa on Music Audi on Previous Music Next Music Icon Melody Descrip on Tap "Se ng" for alarm panel se ngs Tap Arm icon, the sensors synchronized with the alarm panel will be armed. Tap Sensors icon to add sensors Tap "Disarm" icon, the sensors synchronized with alarm panel will be disarmed. Click to choose the music Sensor Se ng Zone Se ng Click to enter Zone se ng then click Zone 1 to setup Zone 1 and so on

9 Name Zone Name Alarm Switch Push Switch Interval Remind Time Music List Voice Descrip on Click to setup the zone name ON: System will alarm when triggered. OFF: System will NOT alarm when triggered. ON: System will send no fica on when triggered. OFF: System will NOT send no fica on when triggered. Click to choose the tes ng interval. Maximum 4 seconds. Click to choose the remind mes. Maximum 4 mes. Click to choose the music ON: System will remind you when triggered. OFF: System will NOT remind you when triggered. Please note: If the alarm switch is off, it won't have the voice reminder. Trigger the Sensor 1 foot away Add or Delete sensors Click Add to add sensor. LED will stay in RED, then wave your hand before the sensor to trigger the sensor, the host will "BEEP" twice and flash twice, indica ng the sensor is successfully bound to the defense zone. If the host "BEEP" and flash once, indica ng that this sensor has been bound into other zones. Click Del to delete the sensor, the LED will flash and beep four mes. Customer can also click the Car to choose Come in or Go away Status Se ng Bu on Click for more se ng

10 4.3 Installing your Sensor We recommend moun ng the mo on sensor at least 3 to 4 (1 m) above the ground and (6-8m) away from the driveway on a sturdy, non-metal surface (i.e. a wall, wooden post or tree). This will decrease or eliminate false alarms from small animals, give you a longer area to pick up movement, and avoid unwanted alarms from nearby lawns/roads. Name Descrip on Device Name Password Timing Se ngs Don't Disturb Push Switch Click to setup the device name Setup the password of the system, default password is 1234 Set up the auto Arm/Disarm me Set up the don't disturb me, when on, you will not receive the no fica on when the system was triggered. Setup the nullifica on you want to receive Please Note: Always test that your sensor is working in your desired loca on before installing it. Avoid placing your sensor in a loca on where sunlight will directly into the sensor eye. Direct sunlight may cause false alarms and/or damage to the PIR sensor

11 4.4 Adjus ng Sensor Field of View Expect for the adjustable detec ng distance, customer can also adjust the view degree by changing the cover Chapter 5 Low Ba 10 5 ery Indica on 5.1 Sensor Low ba ery Indica on When the sensor is in low ba 90 5 ery, it will send a low signal to t h e h o st, w h i l e t h e h o st re c e i ves t h e s i g n a l f ro m corresponding defense zone, the LED will flash 3 mes sugges ng that the sensor of this Zone is in low power, customer should replace ba no fica on from APP too. ery. Customer will get the Chapter 6 Factory Reset Long press the and at the same me then plug in the receiver, the host will beep once and and the LED will flash red once then release the bu on, the music will return to original se ng. Please note, the sensor is s ll bound to the host. Chapter 7 LED Indicator ZONE SETTING Defense Zone 1 Defense Zone 2 Defense Zone 3 Defense Zone 4 Defense Zone 5 Defense Zone 6 Chapter 8 Total Clear LED INDICATOR RED GREEN BLUE PURPLE CYAN YELLOW Long press a er the host is powered on, wait un l the slow "BEEP" sound and green light flashing 10 mes, when the green LED flashing fast means the host has total clear and delete all the sensors, the host will return to the factory state

12 Chapter 9 Specifica on Opera ng voltage: External USB-5V DC power supply / 3 AA ba eries Shutdown Current: <10uA Working Current: <80mA Receiving Frequency: 433MHz Receiving Distance: 350m (Open Area) Chapter 10 Alexa Control Foreword: BIBENE N9 works with Alexa, once you have added to N9 (Skills Name) into Alexa, you can Arm/Disarm your N9 alarm system anywhere with your IOS/Android Smartphone or tablet. Step2:Click Skills and go to home page. You have to ac vate them in a specific way: "Alexa, tell [white tower] to arm". "Alexa, tell [white tower] to disarm". For example, "Alexa, Tell white tower to disarm." Prepare Before Use: Please download Alexa free App in your smartphone first and make sure the Echo have connected with Wi-Fi already. Add N9 from Skills into Echo: Step1: Login in Alexa

13 Step3:Search for N9 and Enable the App binding. Step5:Please click Yes and Go to Set PIN. Step4: Please sign in with your N9 App account and password you have registered already. Step6: Setup a 4 digits PIN code. (Only Digits is acceptable) N

14 Delete the N9 Skill. Enter Your Skill and disable Skill to delete. DISABLE SKILL SETTINGS 24