CPVan Home Alarm Starter Kit

Size: px

Start display at page:

Download "CPVan Home Alarm Starter Kit"

Shawn Curtis
5 years ago
Views:

1 CPVan Home Alarm Starter Kit

For CPVan Home Alarm System Box contents IMPORTANT: Please also refer to www.cpvans.com for further information and technical assistance.

1 x Alarm unit 2 x Door/Window sensor units 2 x Door/Window sensor magnets 2 x AAA LR03 batteries, alkaline Remote control Introduction Product Overview Congratulations with your new CPVan Home Alarm

2 For CPVan Home Alarm System Box contents IMPORTANT: Please also refer to for further information and technical assistance. We are improving our site continuously to make sure you have the best possible experience with our products. We normally respond within 24 hours to any questions. 1 x Alarm unit 2 x Door/Window sensor units 2 x Door/Window sensor magnets 2 x AAA LR03 batteries, alkaline Remote control Introduction Product Overview Congratulations with your new CPVan Home Alarm Starter Kit. The CPVan Home Alarm Starter Kit is a versatile alarm system that helps you to detect if people or animals are entering your home or shop. It allows you to use several different detection units and technologies with one or more Alarm units in up to 4 different zones. These detection units (PIR Motion Sensor, Window/Door sensor) are wirelessly connected with an Alarm unit. This Alarm unit can be set to either produce a Chime sound or an alarming and loud Siren. The alarm unit can be placed on a fixed position or taken with you as you move around the house or if you go to sleep. A maximum of 10 sensors can be assigned to each of the 4 zones to a maximum of 40 per Alarm unit. Each sensor can be paired with several Alarm units if required. Also, up to 20 remote controls can be paired with each Alarm unit to enable you to equip each of your family or team members with a remote control. Important: Extending your CPVan Home Alarm Starter Kit: Only select devices from the CPVan Home Alarm System. Other devices will not be compatible. Just contact us at info@cpvans.com for advice. We normally respond within 24 hours. 01 Alarm unit A A. Siren B. SET button [ C. Visual Indicator for 4 different zones D. On/Off Button [ B D C Door & window sensor E.Sensor E F. Magnet F The sensor contains the electronic detection system for the magnet. If the magnet is separated from the sensor, a wireless signal is sent to the Alarm unit. The Alarm unit will then transmit an audible signal (alarm). 02

Using the Alarm unit Remote Control Bell button: triggers a loud emergency alarm Away button: activate the Alarm unit Disarm: deactivate the Alarm unit Switch Voice: Switch from Chime to Siren and

3 Using the Alarm unit Remote Control Bell button: triggers a loud emergency alarm Away button: activate the Alarm unit Disarm: deactivate the Alarm unit Switch Voice: Switch from Chime to Siren and vice versa First preparation of the Alarm unit Insert 2 AAA batteries in the Alarm unit and close the lid. You will hear a beep and the indicator light on the Alarm unit will light up from top to bottom. Your Alarm unit is now active. Take out the insulating strip in each Door sensor (inside Lithium battery). Please note the correct orientation of the batteries (+ /-). Pressing the buttons IMPORTANT: There are 2 ways to press the buttons on your Alarm unit. Short press: press the button for 1 second or less. Long press: keep the button pressed for 5 seconds. Usually, the long press of 5 seconds is used to enter a programming or pairing mode. This procedure prevents that important settings are changed accidentally. 03 The alarm unit can be operated both through the remote control as well as by pressing the buttons on the side. Switch On: Long press the On/Off Button [ to switch the unit on. The lights on the front will light up one by one from top to bottom when the unit is switched on and a beep will be heard. Switch Off: Long press the On/Off Button [ to switch the unit off. The lights on the front will dim one by one from bottom to top when switching off. A beep will be heard. Arm/Disarm: Make sure the Alarm unit is switched on. Now, short press the SET button [ once. A beep will be heard and the visual indicator will light up once when the unit is armed, and 2 beeps will be heard and the visual indicator will light up twice if the unit is disarmed. IMPORTANT: Your Alarm unit is equipped with a memory function. This means that the Alarm unit will always come back to its last settings when switched on. If it was armed when it was switched off, it will be armed when it is switched On again. However, if it was disarmed when it was switched Off, it will be disarmed when switched On again. In this case, to arm the Alarm unit just short press the SET button [. Change the sound: Make sure the Alarm unit is switched on. Toggle Change the between sounds by short pressing the On/Off Button [. A short confirmation sound will be heard if the sound is changed. Entering the Pairing mode: Make sure the Alarm unit is switched On.Long press the SET button [. All the lights on the front of the Alarm unit are now lit. Select a zone in pairing mode: In Pairing mode, short press the SET button [ to switch between zones modes. See the Chapter Pairing with sensors and remote controls for further instructions on how to pair devices with the Alarm unit. 04

4 When a sensor is triggered: The sound will be heard, Chime or Siren. If the Siren is selected as a notification sound, the LED lights will indicate which zone triggered the alarm (one of the four LEDs will light up). If the Chime sound was selected as a notification sound, all 4 LEDs will light to indicate a sensor was triggered but the zone will not be indicated. Using the remote control The supplied remote control will work with multiple Alarm units if required. There are four buttons on the remote control: Button Arm button Disarm button Switch Voice button Action Switch On Switch Off Change siren type Siren changes from chime to siren or vice versa Bell Button Alarm will sound Siren sounds loud. Press Disarm button to stop. Installation of a door sensor What happens if pressed Alarm unit is activated Alarm unit is deactivated GENERAL GUIDELINES: Do not install the Door/Window sensors on breakable material, but choose instead the frame of a window to attach your Door/Window sensor. Do not install on instable parts. Do not install the sensor near magnetic parts that might trigger the alarm by accident. Clean the surface before installation if the tape will be used for attachment. It is important that the sensor and the magnet are placed on the door and frame respectively to allow an alarm to be triggered when sensor and magnet are separated. Pairing with sensors and remote control The Alarm unit is already paired with the remote control and the door sensors. Use this procedure to connect more door & window detectors from the CPVan Home Alarm System. IMPORTANT: Factory setup: The visual indicator on the front of the Alarm unit has 4 LED s which can be used to see which zone is activated in Siren mode (but not in Chime mode). Please note that one door sensor has been paired with Zone 1 and the other door sensor has been paired to Zone 2 out of the factory as a standard. This will get you started quickly. IMPORTANT: In the procedure below you will need to activate sensors to pair them with the Alarm unit. A door sensor can be activated by keeping the sensor and magnet against each other and then move them away from each other. A PIR sensor can be activated by waving your hand in front of it

5 Entering pairing mode Make sure the Alarm unit is On.If this is not the case, long press the On/Off Button [. Long press the SET button [ on the Alarm unit to enter pairing mode. The four lights on the front will light up. Setup Zone 1 Now short press the SET button [ once to select Zone 1. The first upper light is now lit. Activate the respective unit ( door sensor or PIR ) which corresponds to Zone 1. Two beeps will be heard. The sensor for Zone 1 is now properly connected. Other sensors can be connected for this zone by activating it at this stage. Press the On/Off Button [ to exit the pairing mode OR pair another sensor for the next zone: Setup Zones 2-4 Now short press the SET button [ again to select the next zone. The second upper light is now lit. Activate the respective units ( door sensor or PIR ) which correspond to Zone 2. Two beeps will be heard. The sensor for Zone 2 is now properly connected. Other sensors can be connected for this zone by activating it at this stage. Short press the SET button [ to select Zone 3 or Zone 4 and do as described to add further sensors Press the On/Off Button [ to exit the pairing mode. Pairing with remote control Your remote control is ready for use and already paired with 07 your Alarm unit but you can add more remote controls if desired. 1. Enter the pairing mode by long pressing the SET button [. All red lights are now lit. 2. Press the arm or disarm button on your remote once. Two beeps will be heard as a confirmation. 3. Press the On/Off Button [ on the Alarm unit to exit the pairing modeyour remote control is now paired. Multiple remotes can be connected to any Alarm unit. Also, the remote control can be linked to multiple Alarm units using the method described. Unpairing remote controls and sensors with the Alarm unit Zones can be reset individually. Doing so allows you to disconnect the sensors for just that zone. The Alarm unit also can be disconnected from all remote controls (if you are using more than one). IMPORTANT: If more than one remote control is used with the Alarm unit: Please be aware that there is no option to disconnect just one remote control. With this procedure, all remote controls are unpaired. Please make sure to again pair the remote controls you wish to continue to use after you unpaired them. Deleting the remote control 1. Enter pairing mode by long pressing the SET button [ when the Alarm unit is on. All four lights are now on. 2. Now, again long press the SET button [. 5 Beeps will be heard and the light will flash. All remote controls have now been disconnected from your Alarm unit. 08

Now, again long press the SET button [. 5 Beeps will be heard and the light will flash. The settings for this zone have now been cleared. Changing the batteries 1.

6 Deleting the sensors for one zone. 1. Enter pairing mode by long pressing the SET button [ when the Alarm unit is on. All four lights are now on. 2. Now, again short press the SET button [ one- or multiple times to select the zone you d like to reset. The respective light on the visual indicator will light up. 3. Now, again long press the SET button [. 5 Beeps will be heard and the light will flash. The settings for this zone have now been cleared. Changing the batteries 1. Remote control: The battery can be changed by open the cover on the back of the remote control. Remove the back panel and replace the battery. The battery type is CR2032 (3V, Lithium battery). 2. Alarm unit: Slide off the back panel and replace the batteries with 2x AAA size 1.5V Alkaline batteries. 3. Door sensor: Remove the back panel by open the cover and replace the battery with a new one. The battery type is CR2450 (3V, Lithium battery). Adding Alarm units, remote controls and sensorsthis CPVan alarm system is extremely versatile and flexible. If you have a starter kit installed, you can add many more CPVan sensors to adapt it to your exact requirements. You can extend your system with more CPVan Door and Window or PIR Motion sensors.up to 10 sensors per zone in total 40 sensors. Another great feature is that the system can be expanded with more Alarm units because each sensor can be connected to 09 multiple Alarm units. This allows you to hear the alarm at multiple places, eg in your living room as well as in your bed room. Each Alarm unit can be set with different alarm sounds (Siren or Chime) if required. Adding remote controls is easy. Each alarm unit can be paired with 5 or more remote controls and each remote control can control multiple Alarm units simultaneously. This means that each member of your family or team can switch the system on or off when they require it. Your home will never be unprotected. IMPORTANT: If you want to add remote controls and sensors, please only select devices from the CPVan Home Alarm System. Other devices will not be compatible. You can always ask us at info@cpvans.com if you need advise. We normally respond within 24 hours. CPVan door/window sensor CPVan PIR Motion sensor The CPVan Home Alarm System can be extented panded with more Alarm units because each sensor can be connected to multiple Alarm units. This allows you to hear the alarm at multiple places, e.g. in your living room as well as in your bed room. Each Alarm unit can be set with different alarm sounds (Siren or Chime) if required. 10

7 Frequently asked questions Q: The Alarm unit does not give an alarm when a detector is activated A1: Maybe the system is not armed yet. Long press the On/Off button to switch the Alarm unit on. Short press the On/Off button to arm the device. A2. Are the sensors active? The red light on the sensor should light up if the sensor is activated. A3. Maybe the batteries are running empty. In this case, replace the batteries A4. Sometimes the signal cannot penetrate concrete walls or cover large distances between Alarm unit and the sensor. Take the Alarm unit and hold it close to the sensor whilst activating it. This will show if the distance between the units is too high. A1: The signal might not penetrate thick concrete walls or cover large distances. Try holding the remote control closer to check this. A2: Try opening the remote control and taking the battery out- and back in again. A3: The battery is running out of power. Insert a new battery. Q: Where can I find more information and instructional video s? A: Please visit for additional information. Q: I want to add sensors like a window & door sensor or another PIR motion detector. Where can I find these? A: All our products are offered on Amazon CPVan Storefront. You can also visit for more information availability. Q: I have a question and cannot find the answer in this manual A: Just send your question to info@cpvans.com. We respond usually within 24 hours. Q: The Alarm Unit does not enter pairing mode when pressing the SET button [ A: The device might be switched off. Try long pressing the On/ Off button to switch the unit on. Now, enter Pairing mode by long pressing the SET button [. Q: The device does not switch on A1: Maybe the On/Off button is not pressed long enough. Press it continuously for at least 5 seconds. A2: Check the batteries. They might be empty. Q: The remote-control indicator light is on when I press a button but the Alarm unit does not react to it

D3D Wi-Fi GSM Smart Alarm System -User Manual

D3D Wi-Fi GSM Smart Alarm System -User Manual D3D Wi-Fi / GSM Smart Alarm system (Model : D10). Please read all instructions carefully & follow steps for easy home installation. 1 P a g e D3D Wi-Fi / GSM