EC TYPE-EXAMINATION (MODULE B) CERTIFICATE No. BSI/A.1/3.46/560436

Size: px

Start display at page:

Download "EC TYPE-EXAMINATION (MODULE B) CERTIFICATE No. BSI/A.1/3.46/560436"

Elvin Summers
6 years ago
Views:

1 EC TYPE-EXAMINATION (MODULE B) CERTIFICATE No. BSI/A./3.46/ This is to certify that BSI did undertake the relevant type approval procedures for the equipment identified below which was found to be in compliance with the Fire protection requirements of Marine Equipment Directive (MED) 96/98EC, as amended, tast amended by Directive EC, subject to any conditions in the schedule attached hereto. Applicant Address Martufacturer Address Annex Al ftem Product FirePro Systems Limited 6 Koumandarias & Spyrou Araouzou Street Tonia Court No2, 6 ' Floor Limassol 3036 Cyprus FirePro Systems Limited Ayios Athansios 4 Falea Street Limassol District Cyprus A./3.46 Equivalent fixed gas fire extinguishing systems for machinery spaces (aerosol systems) Aerosol Fire Extinguishing System Units with dry condensed extinguishing agent, Fire Class A & B Product Description FP2OS, FP4OS, FP8OS, FP00S, FP200S, FP500S, FP200, FP2000, FP3000 & FP5700. Specified Standard MO MSC/Circ.007, MSC/Circ 270 The attached schedule of approval forms part of this certificate. First Issued: 20 August 200 For and on behatf of the BSI, a Notified Body for the above Directive Notified Body Number Date of issue: 23 March 202 Expiry date: 9 August 205 Gary Fenton, Global Assurance Director Notes: (i): This BSI/A./3.46/ issue 2 certificate will not be valid if the manufacturer makes any changes or rnodifications to the approved equilsment. which have not been notified to. and agreed with the notified body named on this certificate. (ii): Should the specified regulations or standards be amended during the vatidity of this certificate. the product(s) is/are to be reapproved prior to it/they being placed on board vessels to which the amended regulations or standards apply. (iii): -The Mark of Conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production-control phase module (D) of ANNEX 8 of the Directive is fully complied with and controlled by a written inspection agreement with a notified body." iv) "Wheelmark" Forrnat yy Last two digits of year mark affixed Notified Body number undertaking surveillance module 0086/vy Sheet of 9 MIL raising standards worldwide" 2, Information and Contact BSI, Kdemark Court Davy Avenue, Knowlhill, Milton Keynes MK5 8PP Tel +4, (0) OOO UKL,,,t ed,,egméfee Encr,c; unde, 78e53' d? 389 4; tr,d;,-)04 4 tir asi

2 No. BSI/A./ Date: 23 March 202 Product Specification FP2OS : Aerosol generating fire extinguishing system unit with 20g dry condensed extinguishing agent, thermal activation by thermocord at 72 C, Fire Class A & B FP4OS : Aerosol generating fire extinguishing system unit with 40g dry condensed extinguishing agent, thermal activation by thermocord at 72 C, electrical (6-36 V D/C 0.8 A in 3-4 sec), heating FP8OS Aerosol generating fire extinguishing system unit with 80g dry condensed extinguishing agent. thermal activation by thermocord at 72 C, electrical (6 36 V D/C 0.8 A in 3-4 sec), heating element with 2.3 ohm resistance Fire Class A & B FP00S : Aerosol generating fire extinguishing system unit with 00g dry condensed extinguishing agent, thermal activation by thermocord at 72 C, electrical (6-36 V D/C 0.8 A in 3-4 sec), heating FP200S : :Aerosol generating fire extinguishing system unit with 200g dry condenseci extinguishing agent, thermal activation by thermocord at 72 C, electrical (6-36 V DiC 0.8 A in 3-4 sec), heating FP500S : :Aerosol generating fire extinguishing system unit with 500g dry condensed extinguishing agent, thermal activation by thermocord at 72 C, electrical (6-36 V D/C 0.8 A in 3-4 sec), heating FP200 : :Aerosol generating fire extinguishing system unit with 2009 dry condensed extinguishing agent, thermal activation by thermocord at 72 C, electrical (6-36 V D/C 0.8 A in 3-4 sec), heating FP2000 : :Aerosol generating fire extinguishing system unit with 2000g dry condensed extinguishing agent. thermal activation by thermocord at 72 C, electrical (6-36 V DIC 0.8 A in 3-4 sec), heating FP3000 :Aerosol generating fire extinguishing system unit with 3000g dry condensed extinguishing agent, thermal activation by thermocord at 72 C, electrical (6-36 V D/C 0.8 A in 3-4 sec), heating FP5700 : :Aerosol generating fire extinguishing system unit with 5700g dry condensed extinguishing agent, thermal activation by thermocord at 72 C, electrical (6-36 V D/C 0.8 A in 3-4 sec). heating raising standards worldwide - Sheet 2 of 9 immkerils Information and Contact: 85, Kiternark Court, Davy Avenue. Know(hdl, MiRon Keynes MK5 8PP Te ~44 (0) , iksurarksc i t undeu, :e,ica'red 3 E r lanj tinder : 3S9 4Al. 3. Iib3,gie

Certificate No. BSIIA.3.46560436 Date: 23 March 202 Approval Documentation that forrns part of this certification: Drawing No. C2OASS C4OASS C8OASS ClAS Rev./ lssue No.

3 Certificate No. BSIIA Date: 23 March 202 Approval Documentation that forrns part of this certification: Drawing No. C2OASS C4OASS C8OASS ClAS Rev./ lssue No Date 7/0/2009 6/0/2008 6/0/ /05/2009 Title FP2OS General Assembly Drawing FP4OS General Assembly Drawing FP8OS General Assembly Drawing FP00S General Assembly Drawings C2AS 2 25/05/2009! FP200S General Assembly Drawings C5AS 2 6/02/2009 FP500S General Assembly Drawings B2AS 0 0/0/2008 FP200 General Assembly Drawing B2EH 0 0/0/2008 FP200 External Housing Construction Drawing B2IH 0 ' 0/0/2008 FP200 Internal Housing Construction Drawing B2IAS 0 0/0/2008 FP200 Internal Assembly Drawing B2OAS 0 0/0/2008 FP2000 General Assembly Drawing B2OIAS 0 00/2008 FP2000 Internal Assembly Drawing B3OAS 0 0/0/2008 FP3000 General Assembly Drawing B3OIAS 0 0/0/2008 FP3000 lnternal Assembly Drawing 62030EH 0 /0/2008 FP2000 & FP3000 External Housing Construction Drawing B2030IH 0 0/02008 FP2000 & FP3000 Internal Housing Construction Drawing B22020BRKT 0 0/0/2008 FP200 Mounting Bracket B2030BRKT 0 0/0/2008 FP2000 & FP3000 Mounfing Bracket B57EH 0/0/2008 FP 5700 External Housing Construction Drawing /0/2008 FP5700 lnternal Housing Construction Drawing B57IAS 0 0/0/2008 FP5700 Internal Assembly Drawing B57BRKT 0 0/0/2008 FP5700 Mounting Bracket AELACT 0 0/0/2008 Electrical Activators for ail s where fitted Sheet 3 of 9 Mr 490 raising standards worldwide" 20,Z Information and Contact: BS, Kternark Court, Davy Avenue, KnowINI, MiOon Keynes MKS 8PP Te 4-440) !: bmneci, re,gmeretlin Engi."0,(i unde al 385 Rcad, A ws

4 -70,Wia".~E;,~Z- 'Z43:,W*ZZ-':=7, ""s..m.o,lexii-~:7o4,2:4,~7:4,colf.~ctart7idg'rl''''."7" F Certificate No. BSI/A/3.46/ Date: 23 March 202 Approval Documentation that forms part of this certification: Supporting Documentation Technical Dossier Technical Dossier Reports & Certificates 22/07200 SMO Ref Electronic copy of the Technical file covering all models listed on page Feb 202 Updated to include minor changes to some drawings, Efectis Witness Test Report and Updated KIWA Certificate KIWA Certificate K2477/08 0/04200 UL Test Report, Project Ref 05CA05359, File EX6960 USCG Report CG-D Russian Maritime Register of Shipping. approval Certificate Ref dated /06/200 for MCS 270 ' Hughes Associates INC Analysis Report dated Nov 2004 & 5/0/ /08/200 Technical Dossier Assessment Report 24/ Aug 20 K2477/08 0/08/20 26/0/202 Cone Calorimeter Tests of IMO MSC Circ 270 Class A Plastic Materials Hughes Associates Inc Jan 202 Efectis Test Report R34, Fire test - Wood Cribs & Plastic Sheets 2/09/20 KIWA, EMC Test Report EMC Manuals 5 0/0/20 Information, Instruction & User Manual 2 4/02/202 Annex Marine Manual to be read in conjunction with the above manual Protecta Voltavvu l 60 XK ECH Gsm Fax: raising standards worldwide" Sheet 4 of 9 :0,ZP IIII Information and Contact 85, Kotemark Coun, Davy Avenue, Knowlffill, Mdlon Keynes MKS app. Tel. +44 (0i Ass+ïie:ce UKUIn Wd. rerimeri tri fn9i -an nier number ,3; 339n,,n4 fgri ;.,:yrrion `X4 ijf 4re'rtrt- i:+? tr,:á (..c,rnrian

5 Certificate No. BSI/A Date: 23 March 202 DESIGN CALCULATION. AGENT The quantity (mass) of aerosol agent to be used shouid be determined as follows: W Vxq(g) where q = 20 gr/m3 W = Agent mass (g) (Total mass required to protect the specific volume) V = Volume of enclosure (m3) (Protected volume) q = Design application density (gr/m3) (net mass of agent per unit volume (g/m3) required by the system designer for the fire protection application) f = Efficiency coefficient of generator's model (%) (net mass of agent delivered by a generator model (size)) Efficiency coefficients (related to each generator model (size)): FP-20SISE= 60% FP-500S = 63% FP-40S= 63% FP-200 = 65% FP-80S= 60% FP-2000 = 6% FP-00S = 63% FP-3000 = 62% FP-200S = 6% FP-5700 = 6% The total number of generators (N) to be used is derived by the following formula N - W (total agent mass) nominal mass (initial rnass of the solid compound) of each generator model (size) Example: FP2000 = 2000 grams of nominal mass FP5700 = 5700 grams of nominal mass Note: If different generator models (size) should be selected, the total mass of extinguishant (solid compound) shall not be less than the quantity required (W). raising standards worldwide' Sheet 5 of 9 Information and Contact: 85, Kiternark Court, Davy Avenue, Mdton Keynes MK5 8PP TeL 4-44 t0) k.:u!ance U. wndea. ret.pstered Ir Enqtand under n ucr,r, d. 3 8e, W4 or, membe,

Certificate No. SSI/A.3.46560436 Date: 23 March 202 TECHNICAL SPECIFICATION FP20S FP2OSE s s FP-20S electrical (6-36 V D/C 0.8 A in 3-4 sec) N/A 30 g 20 g 5 0 seconds 2 0.6 m 65 mm x 32 mm (incl.

6 Certificate No. SSI/A Date: 23 March 202 TECHNICAL SPECIFICATION FP20S FP2OSE s s FP-20S electrical (6-36 V D/C 0.8 A in 3-4 sec) N/A 30 g 20 g 5 0 seconds m 65 mm x 32 mm (incl. connector housing) FP-40S electrical (6-36 V D/C 0.8 A in 3-4 sec) heating element with 2.3 ohm resistance g 5-0 seconds 2.2 m 40 mm x 5 mm FP-80S electrical (6-36 V D/C 0.8 A in 3-4 sec) heating element with 2.3 ohm resistance 870 g 80 g 5-0 seconds 2 2 m 85 mm x 5 mm (incl. connector housing) raising standards worldwide - Sheet 6 of 9 4> 00IMMII Information and Contact: BSI, Kitemark Court, Davy Avenue, KnovvIhilI, Milton Keynes MKS 8PP. TeI +44 (0) ASSt.r.3N,eiK Unided. req,stwed Engiard tinor nurnrwr?cü'32 t Sw_& i4 A rneurtbei the 95 ed-o,:p c,t

7 Certificate No. BSI/A./3.46/ Date: 23 March 202 TECHNICAL SPECIFICATION Nozzle Nozzle FP-00S electrical (6 36 V D/C 0.8 A in 3 4 sec) Heating element with 2.3 ohm resistance Maximum 5 ma 370 g 00 g 5-0 seconds optional m 55 mm x 84 mm (incl. connector housing) FP-200S electrical (6 36 V D/C 0.8 A in 3-4 sec) heating element with 2.3 ohm resistance g 5-0 seconds Optional 2 m 85 mm x 84 mm (incl. connector housing) FP-5005 electrical (6-36 V D/C 0.8 A in 3-4 sec) heating element with 2.3 ohm resistance 3340 g 500 g 5-0 seconds 2.5 m 295 mm x 84 mm (inci. connector housing) raising standards worldwide" Sheet 7 of 9 3,,W information and Contact: 85, Knernark Courl, Davy Avenue, Knuwihill, Mfiton Keynes MK5 8 P P 44 (0) tjr, unted,,a9. I!itered ri England under numbei dt 339 tuvk i ondr.: vs;$ 4A[ A,7! :he 85

8 Certificate No.BSI/A./3.46/ Date: 23 March 202 TECHNICAL ESPECIFICATION Self activation temparature Discharge outiet Seif activation temperature FP-200 electrical (6-36 V D/C 0.8 A in 3-4 sec) heating element 2.3 ohm resistance 0900 g (exci bracket) seconds 3.5 m 26 mm x 300 mm x 67 mm FP-2000 electrical (6-36 V D/C 0.8 A in 3-4 sec) heating element 2.3 ohm resistance 5500 g 2000 g 0-5 seconds 3.5 m 300 mm x 300 mm x 85 mm FP-3000 electrical (6-36 V D/C 0.8 A in 3-4 sec) heating element 2.3 ohm resistance 6300 g 3000 g 5-20 seconds 4 m 300 mm x 300 mm x 85 mm Sheet 8 of 9 II 9 4. raising standards worldwide - Information and Contact: BSI, Kiternark Court, Davy Avenue, Knowlb:II, MlIton Keynes MKS 8PP Tel 0) : As5,rarwt-.8. tirt~ recpstéred unaw nwntier at 389 f!: :\,,,-, t-(qt, 9,833, tondr,r, '44 44d., A mernb, r,e 85! LOmtm,i, e,

Certificate No. BSI/A./3.46560436 Date: 23 March 202 TECHNICAL ESPECIFICATION ModeI FP-5700 electrical (6-36 V D/C 0.8 A in 3-4 sec) heating element 2.

9 Certificate No. BSI/A./ Date: 23 March 202 TECHNICAL ESPECIFICATION ModeI FP-5700 electrical (6-36 V D/C 0.8 A in 3-4 sec) heating element 2.3 ohm resistance g 5700 g 5-20 seconds 8 m 300 mm x 300 mm x 300 mm Conditions of Certification i) The BSI/A./ issue 2 certificate remains valid unless cancelled or revoked, provided the conditions listed below are complied with and the equipment remains satisfactory in service ii) The equipment detailed on page on this certificate is to be manufactured in accordance with Production Quality Assurance system (Module D) iii) Detailed User instructions are to be provided with each product. iv) If the specified standards are amended during the validity of this certificate, this product type is to be reapproved prior to it being supplied to vessels to which the amended standards apply. v) Production tests are to be conducted in accordance with the applicable requirements of the IMO Resolutions and applicable standards and be recorded by the manufacturer in accordance with the approved Production Quality Assurance system (Module 0) of the Marine Equipment Directive. vi) Each item, batch or lot of the equipment is to have the "Mark of Conformity" affixed and be issued with a "Declaration of Conformity". raising standards worldwide" Sheet 9 of 9 40,9. CILWRI Information and Contact: BSI, Kiternark Court. Davy Avenue, KnoviihIII, Mton.eynes MK5 8PP Tel 4-44 (0) ,A ssura r,e, Enulaw undry ni.ar.b Ct sv.aa Hr 44 4AL rref rte, ittt 6-5

10 EC QUALITY SYSTEM (MODULE D) CERTIFICATE No. BSUMEDIPC/ This is to certify that BSI did undertake the relevant type approval procedures for the equipment identified below which was found to be in compliance with the Fire protection requirements of Marine Equipment Directive (MED) 9698EC, as amended, last amended by Directive (200926EC), subject to any conditions in the schedule attached hereto. The Manufacturer Registered office Manufacturing location FirePro Systems Limited 6 Koumandarlas & Spyrou Araouzou Street Tonia Court No2, 6th Floor Limassol 3036 Cyprus Aylos Athansios 4 Falea Street Limassol District Cyprus maintains and apphes a quality system in accordance with the requirements of the Maritime Equipment Directive Annex B, Module D. Scope: A./3.46 Equivalent fixed gas fire extinguishing systems for machinery spaces (aerosol systems) This certificate remains valid uniess cancelled, expired or revoked. First Issued: Date of issue: Expiry date: 20 August March August 203 For and on behalf of the BS, a Notified Body for the above Directive Notified Body Number Gary Fenton, Global Assurance Director Notes: This BSI/MED/PC/ issue 2 certificate authorises the manufacturer or his authorised representative established within the Community in conjunction with the EC TYPE EXAMINATON (MODULE B) CERTIFCATE of the equipmentisted in the scope to affix the "Mark of Confonnity" (wheelmark). This cedificate loses its vafidity if the manufacturer makes any changes or modifications to the approved quality system, which have not been notified to, and agreed with the notified body named on this certificate and/or after lapse of time, withdrawal or revocation of the EC Examination (Module B) Certificate. Example for the Application of the -Mark of Conformity": "Wheelmark" Forrnat yy Last two digits of year mark affixed Notified Body number undertaking surveillance module Sheet of /yy ~49a raising standards worldwide' Information and Contact B5. Knemark Court, Davy Avenue, Knovvirut, MIlton Keynes MKS 8PP rei: +44 ( R5k AY,WilrKe legistered Engldnd kmder Fluf,lbei.80537m J89 (it,%wick t;0^. goad, Lt:ndor, W4 4-AL ;;F: A yet t. F;', )!

Certificate No. BSUMEDIPC/560437 Date: 23 March 202 Annex to EC QUALITY SYSTEM (MODULE D) CERTIFICATE No. BSI/MED/PC560437 Product Designation Certificate No. Issue Date Notified Body A./3.

11 Certificate No. BSUMEDIPC/ Date: 23 March 202 Annex to EC QUALITY SYSTEM (MODULE D) CERTIFICATE No. BSI/MED/PC Product Designation Certificate No. Issue Date Notified Body A./3.46 FP2OS, FP4OS, FP8OS, FP00S. FP200S, FP500S, FP200, FP2000, FP3000 & FP5700 aerosol generafing fire extinguishing system unit with dry condensed exfinguishing agent, Fire Rating A & B BSIIMEDIA.3.46/ /03/ Conditions of Certification i) This BSUMEO/PC issue 2 certificate rernains valid un(ess cancelled or revoked, provided the conditions listed below are complied with and the equipment rerriains satisfactory in service ii) The equipments detailed above are to be manufactured in accordance with Production Quality Assurance system (Module D) of the Marine Equipment Directive. iii) If the specified standards are amended during the validity of this certificate, the product type are to be re-approved prior to it being supplied to vessets to which the amended standards appty. iv) Production tests are to be conducted in accordance with the applicable requirements of the Directive and be recorded by the manufacturer in accordance with the approved Production Quality Assurance system (Module D) of the Marine Equipment Directive. v) Each equipment is to have the "Mark of Conformity" affixed and be issued with a "Declaration of Conformity". raising standards worldwide' Sheet 2 of 2 wir Arreirr 4, Information and Contact: BSL Oemark Court, Davy Avenue. KnovArldi, M[Iton Keynes MK5 SPO Tel +44 (0) , ancp Llef tirtuti,d. tigivit reti tngiand under ntimeg2, n505;, 38,3 H.qh Pn3(. W4 4AL kik G.!,-!e B5

EC Type Examination Certificate

EC Type Examination Certificate EC Examination Certificate No. BSI/A./3.46/56436 This is to certify that: FirePro Systems Ltd 6 Koumandarias Street & Spyrou Araouzou Tonia Court No.2 Limassol 336 Cyprus Holds Certificate Number: BSI/A./3.46/56436