Maintenance Best Practices & Intervals for Substation Equipment. Presented by: Paul Schlies, President/CEO Energis High Voltage Services, Inc.

Transcription

1 Maintenance Best Practices & Intervals for Substation Equipment Presented by: Paul Schlies, President/CEO Energis High Voltage Services, Inc.

2 Background - 40 Years in the Industry Education NWTC (Northeast WI Technical College) Work History Wisconsin Public Service (WPS) 24 years American Transmission Company (ATC) 6 years Energis High Voltage Resources, Inc. 10 years

3 No One Right Way There s no one answer to a perfect Substation Maintenance Schedule. Today we ll be using our industry and utility experience, but your engineering firm, the manufactures equipment spec s, insurance requirements, and NETA Standards should also be considered. Along with our recommendations, we ve included survey results of maintenance schedules from individuals within the electrical utility. The information is included in the handout for your review, but because of today s time limitations we won t discuss. Electronic copies of this presentation are available.

4 Why Perform Substation Equipment Testing? Safety Public Employees Improve Reliability Reduce customer outages Reduce Costs Reduce unplanned maintenance cost Reduce insurance/liability cost Plan and budget asset upgrades

5 Transformer Testing Power Factor Ratio Insulation Winding Resistance SFRA (Sweep Frequency Response Analysis) DGA and Oil Quality

6 Transformer Maintenance Verify oil level in main tank & LTC Verify oil level in bushing Verify insulator integrity Verify tank integrity and free of oil leak Inspect surge arrestors Verify paint is in good condition Record winding/liquid temperatures (current & max) Record LTC position indicator & operation counter (current & max raise/lower) Verify correct operation of fans and free of bird nests Verify correct operation pumps (if applicable) Verify nitrogen pressure (if applicable) Verify transformer and pad are level Verify control cabinet is free of moisture Verify cabinet heater operation Frequency

7 Transformer Maintenance Thermographic Imaging (Infrared) Transformer oil analysis (DGA) Power factor Winding resistance test Transformer turns ratio test Insulation test Calibrate temperature gauge Verify alarms points Verify Bucholtz relay operation Verify rapid pressure rise relay operation SFRA (sweep frequency response analysis) Vibration & acoustic testing Frequency Annual Annual New install & after fault operation Dependent on criticality of equipment

8 Industry Survey Results Transformers

9 Circuit Breakers Testing Power Factor Speed Micro-ohm Ratio Bushing Current Transformer SF6 Gas Installation Testing (e.g. Air Mag)

10 Circuit Breaker Maintenance Verify breaker is level Verify paint is in good condition Verify insulator integrity Verify SF6 gas pressure (check oil level in oil breaker) Record operation counter number Verify control cabinet is free of moisture and cabinet is working Check control voltages & operation of breaker Thermographic Imaging (Infrared) Verify tank heaters (if applicable) Motion testing (speed test) Micro-Ohm (ductor) contacts Test SF6 gas for moisture, purity & SO2 content Check alarm points in control house Frequency Annual Annual Annual

11 Battery & Charger Testing Specific Gravity Cell Strap Connection Resistance Internal Cell Resistance Voltage Readings

12 Batteries & Charger Maintenance Visual inspection of electrolyte levels Visual inspection of battery jars Verify no battery grounds exist Record battery voltage & current Specific gravity Intercell impedance/resistance Strap resistance Individual cell voltages/total cell voltage Equalize voltages Verify charger alarms Check voltage ripple Frequency Annual Annual Annual Annual Dependent on battery test results Annual Annual

13 Vacuum Breaker Testing Thermographic Imaging (Infrared) Insulation Resistance Test Micro-ohm Contact Resistance Hi-pot Vacuum Bottles

14 Vacuum Breaker Maintenance Verify insulator integrity Verify control cabinet is free of moisture Verify cabinet heater operation Record operation counter number Thermographic Imaging (Infrared) Insulation resistance test Hi-pot vacuum bottles Frequency

15 Relay Testing Perform as found test Perform as left test Test relays to installed setting Trip test relays

16 Relay Maintenance Check relays for damage Found test Left test Trip test relays Frequency 5-10 years 5-10 years 5-10 years

17 Voltage Regulator Testing Maintenance usually based on manufacturers recommended operations and load. DGA Oil Analysis Frequency - Annual or Biannual

18 Circuit Switcher Testing Micro-ohm Insulation Test Verify Mechanical Operation Verify Electrical Operation Frequency for All Every 5 years

19 Questions to Think About If asked by a lawyer that is suing you because of a piece of equipment that did not trip, how would you provide the information asked? How do you document the performed maintenance & testing results? What type of test forms do you have? Where do you have this information at your facility?

20 Testing to NETA Specifications NETA is an organization that serves the electrical testing industry by offering accreditations of 3 rd party electrical testing firms, certifying electrical testing technician and producing American National Standards. Free download available: Appendix B Frequency of Maintenance Test netaworld.org

21 Want a Copy of this Presentation? Talk to Paul, Brad, or Bill. or Send request to: info@energisinc.com Contact information: Paul Schlies pschlies@energisinc.com Bill Gilbert bgillbert@energisinc.com Brad Beyer bbeyer@energisinc.com

22 Questions Thank you for your time and attention.