Home Hardware Setup Guide

Transcription

1 Home Hardware Setup Guide Floor projection, wall projection, flatscreen TV and touchscreen 1

2 Table of contents Floor Projection Ceiling Mounted Wall Projection Ceiling Mounted Flatscreen TV On a Shelf or Table Alternative Hardware Projectors Computers Sensors / Cameras

3 Floor Projection Ceiling Mounted 3 Floor Projection Ceiling Mounted

4 1 4 Floor Projection Ceiling Mounted

5 2 5 Floor Projection Ceiling Mounted

6 3 USB 3.0 MALE TO FEMALE ACTIVE EXTENSION CABLE ORBBEC MOUNT ORBBEC ASTRA PRO PROJECTOR MOUNT PROJECTOR ORBBEC FIELD OF VIEW PROJECTION COMPUTER POWER PROJECTION SURFACE 6 Floor Projection Ceiling Mounted

7 INSTRUCTIONS FOR USE Connect to the Internet to download your Lumo Play software from install it and register the software. Follow the instructions that came with your projector mount to install it on the wall. Plug your projector into the power outlet. Place your computer where it will be stored permanently. Turn it on. Connect to the Internet. Connect the computer to the projector using an HDMI cable. Follow the instructions that came with your camera mount to install the Orbbec Astra Pro sensor on the ceiling. GOOD TO KNOW Devices may get warm while in use; this is completely normal and they will gradually cool down again after they are turned off. We strongly recommend using cable protection channels to keep stray power and usb cables away from little hands. Please check with your projector manufacturer to make sure your projector can be safely used in a vertical position (pointing at the floor). It is recommended that you use LED or LED laser/hybrid projectors for vertical projection. Projectors with LED bulbs and heat vents on the side or back of the projector are generally safe to use. Connect the USB 3.0 male to female active extension cable to the Orbbec Astra Pro. Plug the USB connector into a USB 3.0 (blue) port of your computer. Once the hardware is in position (see illustration 3) run the Lumo Play software and follow the installation wizard to calibrate the software and run a game. 7

8 Wall Projection Ceiling Mounted 8 Wall Projection Ceiling Mounted

9 1 9 Wall Projection Ceiling Mounted

10 2 10 Wall Projection Ceiling Mounted

11 3aORBBEC ASTRA PRO ORBBEC MOUNT USB 3.0 MALE TO FEMALE ACTIVE EXTENSION CABLE PROJECTOR MOUNT PROJECTOR ORBBEC FIELD OF VIEW PROJECTION PROJECTION SURFACE 11 Wall Projection Ceiling Mounted

12 3b PROJECTOR MOUNT PROJECTOR PROJECTION ORBBEC ASTRA PRO ORBBEC MOUNT PROJECTION SURFACE ORBBEC FIELD OF VIEW 12 Wall Projection Ceiling Mounted

13 INSTRUCTIONS FOR USE Connect to the Internet to download your Lumo Play software from install it and register the software. Follow the instructions that came with your projector mount to install the projector mount on the ceiling. Plug your projector into the power outlet. Place your computer where it will be stored permanently. Turn it on. Connect to the Internet. Connect the computer to the projector using an HDMI cable. 3a. Follow the instructions that came with your camera mount to install the Orbbec Astra Pro sensor on the ceiling. GOOD TO KNOW Devices may get warm while in use; this is completely normal and they will gradually cool down again after they are turned off. We strongly recommend using cable protection channels to keep stray power and usb cables away from little hands. Please check with your projector manufacturer to make sure your projector can be safely used in a vertical position (pointing at the floor). It is recommended that you use LED or LED laser/hybrid projectors for vertical projection. Projectors with LED bulbs and heat vents on the side or back of the projector are generally safe to use. 3b. Follow the instructions that came with your camera mount to install the Orbbec Astra Pro sensor on the wall. Connect the USB 3.0 male to female active extension cable to the Orbbec Astra Pro. Plug the USB connector into a USB 3.0 (blue) port of your computer. Once the hardware is in position (see illustration 3a or 3b) run the Lumo Play software and follow the installation wizard to calibrate the software and run a game. 13

14 Flatscreen TV On a Shelf or Table 14 Flatscreen On a Shelf or Table

15 1 15 Flatscreen On a Shelf or Table

16 2 16 Flatscreen On a Shelf or Table

17 3a ORBBEC ASTRA PRO USB 3.0 MALE TO FEMALE ACTIVE EXTENSION CABLE FLATSCREEN TV COMPUTER ORBBEC FIELD OF VIEW 17 Flatscreen On a Shelf or Table

18 3b FLATSCREEN TV ORBBEC ASTRA PRO USB 3.0 MALE TO FEMALE ACTIVE EXTENSION CABLE COMPUTER ORBBEC FIELD OF VIEW 18 Flatscreen On a Shelf or Table

19 INSTRUCTIONS FOR USE Connect to the Internet to download your Lumo Play software from install it and register the software. Plug your flatscreen TV into the power outlet. Place your computer where it will be stored while you are playing the games. Turn it on. Connect to the Internet. Connect the computer to the flatscreen using an HDMI cable. GOOD TO KNOW Devices may get warm while in use; this is completely normal and they will gradually cool down again after they are turned off. We strongly recommend using cable protection channels to keep stray power and usb cables away from little hands. 3a. Set up the Orbbec Astra Pro sensor just below the flatscreen TV. 3b. Setup the Orbbec Astra Pro sensor on a shelf above the flatscreen TV. Connect the USB 3.0 male to female active extension cable to the Orbbec Astra Pro. Plug the USB connector into a USB 3.0 (blue) port of your computer. Once the hardware is in position (see illustration 3a or 3b) run the Lumo Play software and follow the installation wizard to calibrate the software and run a game. 19

20 Alternative Hardware Projectors, Computers, Sensors & Cameras 20 Alternative Hardware

21 Projectors Chick here to shop! 21 Alternative Projectors

22 Computers Chick here to shop! DESKTOP COMPUTER 22 Alternative Computers

23 Sensors & Cameras Chick here to shop! (DOES NOT WORK WITH MAC) 23 Alternative Sensors / Cameras