Subwoofer OWNER'S MANUAL CO104D CO104S CO124S CO124D CO154S CO154D MODEL

Size: px

Start display at page:

Download "Subwoofer OWNER'S MANUAL CO104D CO104S CO124S CO124D CO154S CO154D MODEL"

Lucinda Lester
6 years ago
Views:

1 Subwoofer MODEL CO104S CO104D CO124S CO124D CO154S CO154D OWNER'S MANUAL

2 WHAT S IN THE BOX Inluded in this box are all the neessary mounting hardware and ables for your basi installation. Listed below is a detailed list of the omponents inluded in this system pakage. INSTALLATION Quantity Desription 1 Installation and Operation Manual 1 Orion Cobalt woofer 1 Mounting template Mounting srews The performane of these Cobalt subwoofers is diretly proportional to the quality of the installation. Care taken with the installation proess will be rewarded by years of satisfying performane. If you are unsure of your installation abilities, please refer to your loal authorized Orion dealer for assistane. Orion dealers are trained professionals dediated to extrating the maximum performane out of your Orion system. If you deide to install this speaker system yourself, please read the entire setion on sealed and vented enlosures before starting the installation. TOOLS OF THE TRADE Listed are the majority of the tools required to perform the installation. Having the proper tools will make the installation muh easier. It is very diffiult when you get half way through the installation and disover that you require a speifi tool to get yourself through a partiular part of the installation. Some of these tools are neessities. Some make the job muh easier. Marking Pen Phillips Srewdriver Allen Wrenhes Table Saw Wire Cutters Eletri Drill and assorted Bits Wire Strippers Volt/Ohm Meter (Optional) Jig Saw Wire Crimpers FINDING SPEAKER MOUNTING LOCATIONS Choosing the orret speaker loations will have the greatest effet on the sound quality of the system. Different onsiderations are needed when hoosing the loations that best suit your needs. The loations must be large enough for the speakers to fit. Care is needed to ensure that the loation you have hosen will not affet any of the mehanial or eletrial operations of the vehile. Determining the best loation for the speakers will depend on your osmeti needs and your vehile's interior. If minimal intrusion in your vehile is desired, fatory speaker loations may be the tiket for you. These woofers are too large to fit most fatory loations and typially need enlosures to perform orretly.

3 FEATURES Polypropylene dust ap - moisture and UV resistant. 2 Oversized NBR (Nitrile-butadiene Rubber) surround for linear ontrolled long exursion. 3 Vented paper one - moisture and UV resistant. 4 Custom stamped steel frame. 5 Vented Kapton voie oil former (10 & 12" uses 1.5" voie oil former, 15 use a 2" voie oil former). 6 9mm steel front plate. 7 Large 2 stak erami magnets. 8 8mm steel bak plate/pole piee T yoke assembly " vent. Part of the enhaned voie oil ooling system (fored onvetion). 10 PVC magnet protetor. 11 High temperature Copper voie oil. 12 Venting in voie oil former. Part of the enhaned voie oil ooling system (fored onvetion). 13 Interlaed Conex spider with stithed and looped tinsel leads attahed. 14 Push Terminals. 15 Reversible PVC mounting gasket.

4 WIRING CONFIGURA TIONS The following illustrations provide guidelines on properly onneting your Orion Cobalt woofer to an Orion Cobalt amplifier for maximum performane. Reommended Amplifier Power Continuous Power (RMS) Peak Power (Watts) 1 woofer 100 to to woofers 200 to to woofers 300 to to woofers 400 to to 2400 Parallel Two Speakers ( voie oils) Two voie oil woofers with the two woofers in parallel results in a 2 ohm load to the amplifier. Figure 2 Figura 2 Abbildung 2 1. Connet the speaker in parallel by onneting the two positive () terminals together and the two negative (-) terminals together. 2. Wire the positive () terminals of the woofers to the positive () terminal on the amplifier. Wire the negative (-) terminals of the woofers to the negative (-) terminal on the amplifier.

5 One Speaker ( voie oil) One voie oil woofer results in a load to the amplifier Figure 3 Figura 3 Abbildung 3 1. Connet the speaker by onneting the positive () terminal of the woofer to the positive () terminal on the amplifier. Wire the negative (-) terminal of the woofer to the negative (-) terminal on the amplifier.

6 Series Two Speakers (Single voie oils) Two single voie oil subwoofers with the voie oils onneted in series to result in an 8 ohm load to the amplifier. Figure 4 Figura 4 Abbildung 4 1. Connet the woofers in series by onneting the negative (-) terminal of the first woofer voie oil to the positive () terminal of the seond woofer voie oil. 2. Wire the positive () terminal of the first woofer voie oil to the positive () terminal on the amplifier. Wire the negative (-) terminal of the seond woofer voie oil to the negative (-) terminal on the amplifier.

7 Series/Parallel - 4 Speakers (Single 4 Ohm Coils) 4 single voie oil subwoofers with the voie oils of eah pair of speaker wired in series and then all 4 speakers wired in parallel to result in a load on the amplifier Figure 5 Figura 5 Abbildung 5 1. Connet the negative (-) terminal from speaker 1 to the negative terminal on speaker 3 and then hook that wire to the negative (-) terminal on the amplifier. 2. Connet the positive () terminal from speaker 1 to the negative (-) terminal on speaker 2 3. Connet the positive () terminal from speaker 3 to the negative (-) terminal on speaker 4 4. Connet the positive () terminal from speaker 2 to the positive () terminal on speaker 4 and then hook that wire to the positive () terminal on the amplifer.

8 Parallel Two Speakers (dual voie oils) Two dual voie oil woofers with voie oils in parallel and the two woofers in parallel results in a 1 ohm load to the amplifier. Figure 6 Figura 6 Abbildung 6 1. Connet the speaker in parallel by onneting the four positive () terminals together and the four negative (-) terminals together. 2. Wire the positive () terminals of the woofers to the positive () terminal on the amplifier. Wire the negative (-) terminals of the woofers to the negative (-) terminal on the amplifier.

9 Parallel - One Speaker (dual voie oils) One dual voie oil woofer with voie oils in parallel results in a 2 ohm load to the amplifier. Figure 7 Figura 7 Abbildung 7 1. Connet the speaker in parallel by onneting the two positive () terminals together and the two negative (-) terminals together. 2. Wire both positive () terminals of the woofer to the positive () terminal on the amplifier. Wire both negative (-) terminals of the woofer to the negative (-) terminal on the amplifier.

10 Series-Parallel Two Speakers (dual voie oils) Note: Verify and ensure that the woofer wiring is onneted as shown with the negative onnetion from the first woofer oil onneted to the positive onnetion of the seond woofer oil. Two dual voie oil subwoofers with voie oils in series and then parallel the two series woofers results in an load to the amplifier Figure 8 Figura 8 Abbildung 8 1. Connet eah woofer in series by onneting the negative (-) terminal of the first oil to the positive () terminal of the seond oil. 2. Wire the positive () terminal of eah woofer's first oil to the positive () terminal on the amplifier. Wire the negative (-) terminal of eah woofer's seond oil to the negative (-) terminal on the amplifier.

11 Series-Parallel - Four Speakers (dual 4 Ohm voie oils) Note: Verify and ensure that the woofer wiring is onneted as shown with the negative onnetion from the first woofer oil onneted to the positive onnetion of the seond woofer oil. Four dual voie oil woofers should be wired with the voie oils on eah woofer in series and then parallel the four woofers for a resulting a 2 ohm load to the amplifier Figure 9 Figura 9 Abbildung 9-1. Connet eah woofer in series by onneting the negative (-) terminal of the first oil to the positive () terminal of the seond oil. 2. Wire the positive () terminal of eah woofer's first oil to the positive () terminal on the amplifier. Wire the negative (-) terminal of eah woofer's seond oil to the negative (-) terminal on the amplifier.

12 ENCLOSURE RECOMMENDATIONS Enlosure Details 1. External dimensions alulated for 3/4 building material 2. Inludes speaker displaement 3. Volumes given are net tuning volume 4. Enlosures inlude a minimal amount of damping material. Just enough material to line the inside of the enlosure is required. Cobalt CO104S/CO104D Sealed Enlosure Reommendations A C External Dimensions A = 14 in B = 12.5 in C = 11.5 in Internal Dimensions A = 12.5 in B = 11 in C = 10 in Wall Thikness Front = 0.75 in Side = 0.75 in B Top & Bottom Box Parts Box Shape: Square Prism Top, 1 Bottom: depth () = 11.5 in width (b) = 12.5, 1 Front, 1 Bak: a b d Front & Bak Sides 2 Sides: height (a) = 12.5 in width (d) = 11, height (a) = 12.5 in depth () = 11.5, Figure 10 Figura 10 Abbildung 10 Driver Mounting Front

13 Cobalt CO104S/CO104D Vented Enlosure Reommendations Figure 11 Figura 11 Abbildung 11 A C External Dimensions A = in B = in C = 12 in Internal Dimensions A = in B = in C = 10.5 in Wall Thikness Front = 0.75 in Side = 0.75 in Top & Bottom B Box Parts Box Shape: Square Prism Top, 1 Bottom: depth () = 12 in width (b) = 14.25, 1 Front, 1 Bak: a b d Front & Bak Sides 2 Sides: height (a) = 14.25in width (d) = 12.75, height (a) = in depth () = 12, Sides VENT Round h Driver Mounting Front e e - OR - VENT Square h h g g Vent Parts --- Round 1 Dut: outside diameter (e) = 3.2 in inside diameter (g) = 3 in length (h) = 9.5 in Vent Parts --- Square 1 Top, 1 Bottom: width (e) = 3, length (h) = 10 in thikness = in 2 Sides: height (g) = 2.75, length (h) = 10 in thikness = in

14 Cobalt CO124S/CO124D Sealed Enlosure Reommendations A C External Dimensions A = 15.5in B = in C = 12 in Internal Dimensions A = 14 in B = in C = 10.5 in Wall Thikness Front = 0.75 in Side = 0.75 in B Top & Bottom Box Parts Box Shape: Square Prism Top, 1 Bottom: depth () = 12 in width (b) = 14.75, 1 Front, 1 Bak: a b d Front & Bak Sides 2 Sides: height (a) = 14 in width (d) = 13.25, height (a) = 14 in depth () = 12, Figure 12 Figura 12 Abbildung 12 Driver Mounting Mounting: Front

15 Cobalt CO124S/CO124D Vented Enlosure Reommendations Figure 13 Figura 13 Abbildung 13 A C External Dimensions A = 18 in B = in C = 13 in Internal Dimensions A = 16.5 in B = in C = 11.5 in Wall Thikness Front = 0.75 in Side = 0.75 in a Top & Bottom b d Front & Bak B Sides Box Parts Box Shape: Square Prism Top, 1 Bottom: depth () = 11.5 in width (b) = 12.5, 1 Front, 1 Bak: height (a) = 12.5 in width (d) = 11, 2 Sides: height (a) = 12.5 in depth () = 11.5, e e VENT Round h - OR - VENT Square h h g g Driver Mounting Mounting: Front Vent Parts --- Round 1 Dut: outside diameter (e) = 4.25 in inside diameter (g) = 4 in length (h) = 10 in Vent Parts --- Square 1 Top, 1 Bottom: width (e) = 3.75, length (h) = 10 in thikness = in 2 Sides: height (g) = 3.5, length (h) = 10 in thikness = in

16 Cobalt CO154S/CO154D Sealed Enlosure Reommendations A C External Dimensions A = 25 in B = 17.5 in C = 11.5 in Internal Dimensions A = 23.5 in B = 16 in C = 10 in Wall Thikness Front = 0.75 in Side = 0.75 in B Top & Bottom Box Parts Box Shape: Square Prism Top, 1 Bottom: depth () = 11.5 in width (b) = 17.5, 1 Front, 1 Bak: a b d Front & Bak Sides 2 Sides: height (a) = 23.5 in width (d) = 16, height (a) = 23.5 in depth () = 11.5, Figure 14 Figura 14 Abbildung 14 Driver Mounting Mounting:Front

17 Cobalt CO154S/CO154D Vented Enlosure Reommendations Figure 15 Figura 15 Abbildung 15 A C External Dimensions A = 25 in B = 17.5 in C = 13 in Internal Dimensions A = 23.5 in B = 16 in C = 11.5 in Wall Thikness Front = 0.75 in Side = 0.75 in B a Top & Bottom b d Front & Bak Sides Box Parts Box Shape: Square Prism Top, 1 Bottom: depth () = 13 in width (b) = 17.5, 1 Front, 1 Bak: height (a) = 23.5 in width (d) = 16, 2 Sides: height (a) = 23 in depth () = 13, Sides e e VENT Round h - OR - VENT Square h h g g Driver Mounting Mounting: Front Vent Parts --- Round 1 Dut: outside diameter (e) = 4.25 in inside diameter (g) = 4 in length (h) = 7 in Vent Parts --- Square 1 Top, 1 Bottom: width (e) = 4.25, length (h) = 10 in thikness = in 2 Sides: height (g) = 4, length (h) = 7 in thikness = in

18 SPECIFICATIONS Model/Part Number CO104S CO124S CO154S Thiele/Small Parameters Fs (free-air resonane, Hz) Vas (equivalent ompliane, u. ft.) Vas (equivalent ompliane, liters) Qms (Q, mehanial) Qes (Q, eletrial) Qts (total driver Q) Re (DC resistane, ohms) Z (nominal impedane, ohms) Le (indutane, mh) Effiieny 1M, db) Xmax (one way linear exursion, in.) Xmax (one way linear exursion, mm) RMS Power Watts Nominal Power Watts MAX Musi Power Watts Mms (total moving mass, grams) Cms (mehanial ompliane, mm/n) Bl (motor strength, Tesla-M) Sd (effetive radiating area, sq. m.) Sd (effetive radiating area, sq. in.) Frequeny range (Hz) Energy Bandwidth Produt (EBP) Driver Physial Dimension Speaker Displaement (u ft) Speaker Outer Diameter (inhes/mm) 10.28/ / /393 Mounting hole diameter (inhes/mm) 9.13/ / /351 Mounting depth (inhes/mm) 5.22/ / /172.5 Magnet Weight (Oz) Basket diameter (inhes/mm) 10.16/ / /385 Reommended Enlosures Typial sealed enlosure (u. ft.) Speifiations subjet to hange without notie

19 SPECIFICATIONS Model/Part Number CO104D CO124D CO154D Thiele/Small Parameters Fs (free-air resonane, Hz) Vas (equivalent ompliane, u. ft.) Vas (equivalent ompliane, liters) Qms (Q, mehanial) Qes (Q, eletrial) Qts (total driver Q) Re (DC resistane, ohms) Z (nominal impedane, ohms) Le (indutane, mh) Effiieny 1M, db) Xmax (one way linear exursion, in.) Xmax (one way linear exursion, mm) RMS Power Watts Nominal Power Watts MAX Musi Power Watts Mms (total moving mass, grams) Cms (mehanial ompliane, mm/n) Bl (motor strength, Tesla-M) Sd (effetive radiating area, sq. m.) Sd (effetive radiating area, sq. in.) Frequeny range (Hz) Energy Bandwidth Produt (EBP) Driver Physial Dimension Speaker Displaement (u ft) Speaker Outer Diameter (inhes/mm) 10.28/ / /393 Mounting hole diameter (inhes/mm) 9.13/ / /351 Mounting depth (inhes/mm) 5.22/ / /172.5 Magnet Weight (Oz) Basket diameter (inhes/mm) 10.16/ / /385 Reommended Enlosures Typial sealed enlosure (u. ft.) Speifiations subjet to hange without notie

20 A B C D E Figure 16 Figura 16 Abbildung 16 CO104S/CO104D CO124S/CO124D CO154S/CO154D Dimensions inhes/mm, Dimensions po/mm, Dimensiones plg./mm, Abmessungen Zoll/mm, Dimensioni pollii/millimetri, Dimensões polegadas/mm A 5.22/ / /172.5 B 2.20/ / /62.5 C 5.75/ / /170 D 9.13/ / /351 E 10.28/ / /393

Coaxial Speaker MODEL CO40 CO46 CO52 CO57 CO60 CO65 CO653 CO68 CO69 CO693 OWNER'S MANUAL

Coaxial Speaker MODEL CO40 CO46 CO52 CO57 CO60 CO65 CO653 CO68 CO69 CO693 OWNER'S MANUAL TM Coaxial Speaker MODEL CO0 CO6 CO52 CO57 CO60 CO65 CO653 CO68 CO69 CO693 OWNER'S MANUAL TABLE OF CONTENTS English...................... 1 Français...................... 9 Español....... 13 Deutsch......................