All-fuel, double-wall chimney system. UL 103 HT, UL 103, and ULC S604.
|
|
- Buddy Ellis
- 5 years ago
- Views:
Transcription
1 DuraTech ll-fuel, double-wall chimney system. UL 103 HT, UL 103, and UL S60.
2 DuraTech ll-fuel himney Typical Installations For 5-2 DuraTech *updated typicals* Installation Key 1 DVL or Duralack 11 Tee with Tee ap 2 eiling Support 12 Tee Support 3 Wall Thimble 13 hase Top Flashing himney Pipe 1 ase Tee/Double Tee 5 ttic Insulation Shield 15 nchor Plate or nchor Plate with Damper 6 Flashing 16 Roof Support Storm ollar 1 Finishing ollar 8 himney ap 18 DVL dapter, Duralack Slip onnector, or Snap-Lock dapter 9 Elbow 19 DVL dapter (w/ or w/o damper) 10 Elbow Strap 3 athedral eiling Oil Furnace Refer to our Typical Installation drawings to select the appropriate component parts for your installation. DVL/Duralack himney dapter must be used when connecting DVL pipe to a eiling Support ox or Finishing ollar. When connecting Duralack pipe, a DVL/Duralack himney dapter, Duralack Slip onnector, or Snap-Lock dapter must be used. Wall Thimble must be installed with an appropriate length of chimney pipe for all horizontal through-the-wall installations. To accommodate thicker walls, the telescoping pieces of the Wall Thimble can be separated, and a field-fabricated extension may be installed. ttic Insulation Shield must be used in all installations that pass through an attic, regardless of whether the attic is insulated or not. Firestop Radiation Shield must be used when a chimney passes through a floor or ceiling without a support box. himney ap Extended Roof racket Storm ollar Flashing Through-The-Wall ttic Offset ttic Insulation Shield Firestop Radiation Shield djustable Wall Strap himney Pipe eiling Support ox DVL/Duralack himney dapter DVL or Duralack Pipe ppliance dapter Fireplace (New or retrofit) athedral eiling w/support ox 15 DuraVent
3 DuraTech ll-fuel himney Typical Installations For 5-2 DuraTech *updated typical installations* Installation Key 1 DVL or Duralack 11 Tee with Tee ap 2 eiling Support 12 Tee Support 3 Wall Thimble 13 hase Top Flashing 8 8 himney Pipe 1 ase Tee/Double Tee ttic Insulation Shield 15 nchor Plate or nchor Plate with Damper 6 Flashing 16 Roof Support Storm ollar 1 Finishing ollar himney ap 18 DVL dapter, Duralack Slip onnector, or Snap-Lock dapter Elbow 19 Stove dapter 10 Elbow Strap 3 athedral eiling Oil Furnace Refer to our Typical Installation drawings to select the appropriate component parts for your installation. DVL/Duralack himney dapter must be used when connecting DVL pipe to a eiling Support ox or Finishing ollar. When connecting Duralack pipe, a DVL/Duralack himney dapter, Duralack Slip onnector, or Snap-Lock dapter must be used. Wall Thimble must be installed with an appropriate length of chimney pipe for all horizontal through-the-wall installations. To accommodate thicker walls, the telescoping pieces of the Wall Thimble can be separated, and a field-fabricated extension may be installed. ttic Insulation Shield must be used in all installations that pass through an attic, regardless of whether the attic is insulated or not. Firestop Radiation Shield must be used when a chimney passes through a floor or ceiling without a support box himney ap Extended Roof racket Storm ollar Flashing 19 Through-The-Wall ttic Offset 8 ttic Insulation Shield Firestop Radiation Shield 8 6 djustable Wall Strap himney Pipe 15 1 eiling Support ox DVL/Duralack himney dapter DVL or Duralack Pipe ppliance dapter Fireplace (New or retrofit) athedral eiling w/support ox 15 DuraVent
4 DuraTech 5-8 ll-fuel himney djustable Pipe *updated order #s* Use to add length to DuraTech chimney. djusts from SIZE ORDER # 6DT-21TSS 8DT-21TSS STOK # Elbow Kit Elbow Kit includes: 2 Elbows and 1 Elbow Strap. 30 or 15 ½ Use for offsets around obstructions such as rafters, ridgepoles, or joists. May have two pairs of elbows, if needed. Offsets greater than 30 are not permitted in accordance to UL 103 standards. Elbows swivel 360 at base (angles are not adjustable). pair of elbows is required to return an offset chimney back to vertical. ½ vailable in stainless steel (SS) or galvalume (G) outer wall. G SS G SS ORDER # -- 6DT-E15K DT-E15K 8DT-E15K STOK # ORDER # 5DT-E15KSS 6DT-E15KSS DT-E15KSS 8DT-E15KSS STOK # ORDER # -- 6DT-E30K DT-E30K 8DT-E30K STOK # ORDER # 5DT-E30KSS 6DT-E30KSS DT-E30KSS 8DT-E30KSS STOK # Elbow Strap 2 Use to prevent excessive weight on the elbows by supporting the weight of the chimney. Required to be installed between two elbows in offset installations. Multiple elbow straps may be required for offset installations. Refer to installation instructions. SIZE ORDER # 5DT-ES 6DT-ES DT-ES 8DT-ES STOK # DuraVent
5 DuraTech 5-8 ll-fuel himney ombustion ir Square eiling Support ox *updated illustration* Use with ombustion ir System components. Delivers outdoor air as combustion air to the appliance. Operates as a direct vent system without requiring a second penetration to the building envelope. lack. Patent-pending. For pricing refer to the S price list. SIZE ORDER # 6S-S2DT 6S-S36DT 8S-S2DT 8S-S36DT STOK # Round eiling Support ox 6 Supports chimney pipe and provides a positive connection between support box and chimney with a built-in twist-lock. Supports up to 60' of DuraTech himney. Use adapter to attach DVL or Duralack to the support box. Painted black. Trim collars are sold separately. (For adapters see DVL/Duralack section). SIZE ORDER # 5DT-RS 6DT-RS DT-RS 8DT-RS STOK # Trim ollar For Round Support ox onceals the gap between the Round eiling Support ox and the ceiling cutout. Select square or round. Painted black. ½ ½ SQURE TRIM OLLR SIZE ORDER # 5DT-T DT-T STOK # ROUND TRIM OLLR SIZE ORDER # 5DT-TR DT-TR STOK # DuraVent
6 ll-fuel himney DuraTech 5-8 Flat eiling Support ox 3 Supports chimney pipe and provides a positive connection between support box and chimney with a built-in twist-lock. Designed for installation in flat ceilings only. Supports up to 60' of DuraTech himney. Use adapter to attach DVL or Duralack to the support box. 2 wide trim collar is included. Not painted, but can be painted with high temperature paint. (For adapters see DVL/Duralack section). SIZE ORDER # 5DT-FS 6DT-FS DT-FS 8DT-FS STOK # Roof Support *updated description* 6 Designed to support the DuraTech himney and allows the chimney to pass through the roof and extend down from the ceiling. Ideal for cathedral ceilings and free-standing appliance installations. Supports up to a maximum total chimney length of 5' above and 20' chimney below Roof Support. djustable to different roof pitches. Use Finishing ollar and adapter to attach DVL or Duralack to the DuraTech chimney. Trim ollar not included. SIZE ORDER # 5DT-RS 6DT-RS DT-RS 8DT-RS STOK # Trim ollar For Roof Support onceals gap between chimney pipe and ceiling cut out when used with Roof Support. Galvalume. Painted black. ½ SIZE /12-3/12 ORDER # 5DT-RST3 6DT-RST3 DT-RST3 8DT-RST3 STOK # /12-6/12 ORDER # 5DT-RST6 6DT-RST6 DT-RST6 8DT-RST6 STOK # /12-9/12 ORDER # 5DT-RST9 6DT-RST9 DT-RST9 8DT-RST9 STOK # /12-12/12 ORDER # 5DT-RST12 6DT-RST12 DT-RST12 8DT-RST12 STOK # DuraVent 22
7 DuraTech 5-8 ll-fuel himney Support ox Rails *new product offering* ttach to ouside of Square eiling Support ox to provide level, temporary support. This enables an installer to easily fasten the box in place without the need for another pair of hands. Simplifies installation. SIZE 6 ORDER # 6DT-SRU STOK # Wall Thimble djustable D D djusts from a minimum of to a maximum of 10 wall thickness, and fits between standard wall studs. To accommodate thicker walls, the telescoping pieces can be extended up to 16 with a field-fabricated extension installed. Interior trim ring painted black. Must be installed with DuraTech chimney pipe horizontally through the wall and extend 6 into the room beyond the interior wall. (lack painted DuraTech is available). 6 and 8 stainless steel exterior trim available. SIZE D ORDER # 5DT-WT 6DT-WT DT-WT 8DT-WT STOK # SS TRIM ORDER # -- 6DT-WTSS -- 8DT-WTSS STOK # ombustion ir Wall Thimble Use with ombustion ir System components. Delivers outdoor air as combustion air to the appliance. Operates as a direct vent system without requiring a second penetration to the building envelope. lack. Patent-pending. Ø SIZE 6 8 6" ORDER # 6S-WTDT 8S-WTDT STOK # DuraVent
8 DuraTech 5-8 ll-fuel himney Finishing ollar w/ dapter *updated description* New integrated collar with adapter, fits into the female end of the chimney pipe to provide a decorative black finish. Use on chimney pipe that is suspended with the roof support system or on pipe that is passing through a wall thimble. Provides proper connection to DVL or Duralack. No other adapter is needed. SIZE ORDER # 5DT-F 6DT-F DT-F 8DT-F STOK # nchor Plate Use to attach DuraTech himney to an appliance or masonry fireplace. heck with appliance manufacturer to ensure DuraTech himney is approved for use. 2 SIZE ORDER # 5DT-P 6DT-P DT-P 8DT-P STOK # Transition nchor Plate Use when converting from DuraLiner to DuraTech in chimney restoration. Use with a DuraLiner Slip onnector and Hanger (See DuraLiner section). SIZE ORDER # 6DT-P1x1 6DT-P1x1 6DT-P13x21 6DT-P1x21 STOK # SIZE ORDER # 8DT-P1x1 8DT-P1x1 8DT-P13x21 8DT-P1x21 STOK # DuraVent
9 DuraTech 5-8 ll-fuel himney Finishing ollar w/ dapter New integrated collar with adapter, fits into the female end of the chimney pipe to provide a decorative black finish. Use on chimney pipe that is suspended with the roof support system or on pipe that is passing through a wall thimble. Provides connection to black DVL or Duralack. SIZE ORDER # 5DT-F 6DT-F DT-F 8DT-F STOK # nchor Plate *updated description* Use to attach DuraTech himney to an appliance or masonry fireplace. heck with appliance manufacturer to ensure DuraTech himney is approved for use. SIZE ORDER # 5DT-P 6DT-P DT-P 8DT-P STOK # Transition nchor Plate Use when converting from DuraLiner to DuraTech in chimney restoration. Use with a DuraLiner Slip onnector and Hanger (See DuraLiner section). SIZE ORDER # 6DT-P1x1 6DT-P1x1 6DT-P13x21 6DT-P1x21 STOK # SIZE ORDER # 8DT-P1x1 8DT-P1x1 8DT-P13x21 8DT-P1x21 STOK # DuraVent
10 ll-fuel himney DuraTech 5-8 hase ir Intake w/ Rodent Guard llows required ventilation air into chase. Screen keeps rodents out. SIZE 6 ORDER # 6DT-I STOK # Snow Splitter *updated product* Three times thicker and stronger, allowing it to standup against heavier snow loads. endable attachment flanges allow it to mount on any roof slope. Use to divert snow around chimney, vent and roof flashing. onstructed of paintable galvanized material. Ships flat for easy assembly. Works with 6", ", 8", and 10". SIZE 6 ORDER # 6DT-SP STOK # DuraVent 30
11 ll-fuel himney DuraTech 10-2 Round eiling Support ox Supports chimney pipe and provides a positive connection between support box and chimney. Supports up to 0' of DuraTech himney. Trim collars are sold separately. (For 10 use Duralack Slip onnector to attach Duralack to the support box. See Duralack section). SIZE ORDER # 10DT-RS 12DT-RS 1DT-RS 16DT-RS STOK # Trim ollar For Round Support ox onceals gap between chimney pipe and ceiling cut-out when used with Round eiling Support ox. Galvalume. Painted black. *updated order numbers* ½ SIZE ORDER # 10DT-TR 12DT-TR 1DT-TR 16DT-TR STOK # Wall Thimble djustable D D Use to provide clearance to combustibles. djusts from a minimum of to a maximum of 10 wall thickness, and fits between standard wall studs. To accommodate thicker walls, the telescoping pieces can be extended up to 16 with a fieldfabricated extension installed. Interior trim ring painted black. Must be installed with DuraTech chimney pipe horizontally through the wall and extend 6 into the room beyond the interior wall. SIZE D ORDER # 10DT-WT 12DT-WT 1DT-WT 16DT-WT STOK # DuraVent 3
12 DuraPlus ll-fuel, triple-wall chimney system. UL 103 HT.
13 ll-fuel himney DuraPlus Typical Installations *updated typicals* Installation Key 1 DVL or Duralack Stovepipe 12 Tee Support racket 2 eiling Support ox 13 Wall Strap 3 Wall Thimble 1 Firestop Radiation Shield DuraPlus himney Snap-Lock dapter, DVL/Duralack himney 15 5 ttic Insulation Shield dapter, Duralack Slip onnector 6 Roof Flashing 16 Extended Roof racket Storm ollar 1 DVL or Duralack himney dapter 8 himney ap 18 DVL or Duralack Tee 9 Elbow 19 DVL or Duralack Elbow 10 Elbow Strap 20 hase Top Flashing 11 Tee with ap 21 nchor Plate ttic Offset athedral eiling Roof Support Refer to our Typical Venting Installation drawings to select the appropriate component parts for your installation. DVL/Duralack himney dapter or Duralack Slip onnector must be used when connecting DVL or Duralack stovepipe to eiling Support or Wall Thimble. Snap-Lock dapter must be used when attaching snap-lock stovepipe to DuraPlus. Wall Thimble must be installed with an appropriate section of chimney pipe for all horizontal through-the-wall installations. To accommodate thicker walls a wall thimble extension can be field fabricated. n ttic Insulation Shield must be used in all installations that pass through an attic, regardless of whether the attic is insulated or not. If chimney is enclosed in a chase in the attic space, an ttic Insulation Shield is not required. Firestop Radiation Shield must be used when a chimney passes through a floor or ceiling without a eiling Support ox. himney ap Extended Roof racket Storm ollar Flashing Elbow Strap 6 Through-the-Wall 8 Oil Furnace 8 Elbow ttic Insulation Shield Firestop Radiation Shield himney Pipe Wall Strap * Second Floor hase eiling Support himney dapter Duralack Stovepipe or DVL Stovepipe Stove dapter Manufactured Home *DVL stovepipe required for this installation Fireplace (New or retrofit) DuraVent 6
14 ll-fuel himney DuraPlus asic Kit *updated description* Kit includes: DVL and Duralack himney dapter, Snap-Lock dapter w/ Trim, 11 Square eiling Support ox with Trim, djustable Flashing 0/12-6/12, himney ap, Storm ollar, and ttic Insulation Shield. Only available in 6 diameter. Pipe not included. an be used for flat or vaulted ceiling installations. Use for typical through-the-roof installations. SIZE 6 ORDER # 6DP-KS STOK # Manufactured Home Kit Kit includes: DVL and Duralack dapter, 2 Square eiling Support ox with Trim, djustable Flashing 0/12-6/12, himney ap, Storm ollar, and (2) 2 DuraPlus himney Pipe (galvanized). Only available in 6 diameter. an be used for cathedral ceiling installations. Use for manufactured home through-the-roof installations. SIZE 6 ORDER # 6DP-KMFG STOK # Through-The-Wall Kit Kit includes: DVL and Duralack himney dapter, Snap-Lock dapter w/ Trim, 9 DuraPlus himney Pipe (galvanized), Wall Thimble, Tee w/ ap, (2) Wall Strap, Tee Support racket, and himney ap. Only available in 6 diameter. Use for through-the-wall installations. SIZE 6 ORDER # 6DP-KTTW STOK # DuraVent 8
15 ll-fuel himney DuraPlus v asic Kit *updated photo and description* Kit includes: DVL and Duralack himney dapter, Snap-Lock dapter w/ Trim, 11 Square eiling Support ox with Trim, djustable Flashing 0/12-6/12, himney ap, Storm ollar, and ttic Insulation Shield. Only available in 6 diameter. Pipe not included. an be used for cathedral ceiling installations. Use for typical through-the-roof installations. SIZE 6 ORDER # 6DP-KS STOK # Manufactured Home Kit Kit includes: DVL and Duralack dapter, 2 Square eiling Support ox with Trim, djustable Flashing 0/12-6/12, himney ap, Storm ollar, and (2) 2 DuraPlus himney Pipe (galvanized). Only available in 6 diameter. an be used for cathedral ceiling installations. Use for manufactured home through-the-roof installations. SIZE 6 ORDER # 6DP-KMFG STOK # Through-The-Wall Kit *updated photo and description* Kit includes: DVL and Duralack himney dapter, Snap-Lock dapter w/ Trim, 9 DuraPlus himney Pipe (galvanized), Wall Thimble, Tee w/ ap, (2) Wall Strap, Tee Support racket, and himney ap. Only available in 6 diameter. Use for through-the-wall installations. SIZE 6 ORDER # 6DP-KTTW STOK # DuraVent 8
16 DuraPlus ll-fuel himney Pipe Selection hart himney himney Installed Sections Used Installed Sections Used himney Height himney Height ' ' ' ' ' ' ' ' ' '-3 6' ' ' ' ' ' ' ' ' ' ' ' ' himney Pipe *updated order numbers* Length Ø Ø Designed for appliances tested and listed for use with wood stoves, fireplaces, furnaces, boilers, stoves, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas. 6, 9, and 12 chimney pipe has 1 insulation blanket; 2, 36 chimney pipe has 1 2 insulation. To calculate the installed length of DuraPlus chimney pipe, subtract from each length of chimney pipe. dditional protective carton filler for shipping is available, items have stock numbers with (F). SIZE 6 8 ORDER # STOK # ORDER # STOK # ORDER # STOK # DP DP DP DP DP DP DP DP DP SS 6DP-12SS DP DP DP DP-2F SS 6DP-2SS DP-2SS DP-2SS SS DP-2SSF DP DP DP DP-36F DP-36F SS 6DP-36SS DP-36SS DP-36SS SS 6DP-36SSF DP-36 SSF DuraVent
17 ll-fuel himney DuraPlus Elbow Kit *updated order numbers* Kit includes: (2) elbows and one Elbow Strap. Use for offsets around obstructions such as rafters, ridgepoles, or joists. May have two pairs of elbows, if needed. Offsets greater than 30 are not permitted in accordance to UL 103 standards. Elbows swivel 360 at base (angles are not adjustable). pair of elbows is required to return an offset chimney back to vertical. vailable in stainless steel (KSS) or galvalume (K) outer wall. G SS G SS ORDER # 6DP-E15K DP-E15K 8DP-E15K STOK # ORDER # 6DP-E15KSS DP-E15KSS 8DP-E15KSS STOK # ORDER # 6DP-E30K DP-E30K 8DP-E30K STOK # ORDER # 6DP-E30KSS DP-E30KSS 8DP-E30KSS STOK # Elbow Strap Ø Use to prevent excessive weight on the elbows by supporting the weight of the chimney. Required to be installed between two elbows in offset installations. Multiple elbow straps may be required for offset installations. Refer to installation instructions. 2 SIZE ORDER # 6DP-ES DP-ES 8DP-ES STOK # Round eiling Support Supports chimney pipe and provides a positive connection between support box and chimney with a built-in twist-lock. Supports up to 35 of DuraPlus himney. Use adapter to attach DVL or Duralack to the support box. Painted black. Trim collar included. (For adapters see DVL and Duralack section.) SIZE 6 8 ORDER # 6DP-RS DP-RS 8DP-RS STOK # DuraVent 50
18 DuraPlus HT ll-fuel, double-wall chimney system. UL S629.
19 Specifications pplications DuraPlus HT is a double-wall, all-fuel chimney system for anada for use with wood stoves; fireplaces; and appliances using wood, oil, gas, or coal. Materials and onstruction *updated* lanket insulation encased between inner and outer walls of stainless steel. learances 2 clearance to combustibles. Diameters 6-8 Listings Listed to UL 103HT and UL S629 (13-P-03-2). UL 103 HT and UL S629 System DuraPlus HT *updated* DuraVent's blanket insulation in DuraPlus HT is made of lightweight ceramic refractory material. This insulation will not shrink or cause gaps like competitors products made of mineral wool and other loose-fill insulations. No gaps mean no hot spots to trigger fires to exterior combustibles. Encased between two stainless steel walls, the insulation maintains a barrier that will not shift or settle. The 2 wall keeps the exterior cool, while ensuring high temperatures for optimum draft performance on the inside. Twist-lock feature allows you to assemble DuraPlus HT quickly and precisely. No screws or rivets required and no locking bands needed either. The djustable Tee Support racket is reversible for installation above or below the tee, while ensuring a 2 clearance to combustibles (adjusts from 2 to 6 ). DuraPlus HT offers 15, 30, and 5 degree elbows and allows double offsets. himney pipe comes in lengths from 6 inches up to feet. Designed for normal, continuous operation at 1200 F (650 ) flue gas temperatures. DuraPlus HT is subjected to rigorous and stringent requirements of the UL S629 standard, including one hour at 100 F (925 ), plus three thirty minute chimney fire tests at 2100 F (1150 ). 61 DuraVent
20 ll-fuel himney DuraPlus HT Typical Installations *updated key* Multi-Story athedral eiling Roof Support Installation Key 1 DuraPlus HT himney Pipe 11 Reduced learance Firestop Radiation Shield 2 Elbow 12 Square eiling Support ox 3 Universal Elbow Strap 13 Universal Roof Support Tee w/ ap 1 Trim ollar for Roof Support (not shown) 5 Wall Thimble 15 Roof Flashing 6 djustable Tee Support racket 16 Roof Radiation Shield DVL/Duralack himney dapter 1 DVL or Duralack Stovepipe 8 himney ap 18 Stovetop dapter 9 Storm ollar 19 DVL or Duralack Elbow 10 Finishing ollar Refer to our Typical Venting Installation drawings to select the appropriate component parts for your installation. DVL/Duralack himney dapter must be used when connecting DVL or Duralack stovepipe to a eiling Support, Wall Thimble or Finishing ollar. Wall Thimble must be installed with an appropriate section of chimney pipe for all horizontal through-the-wall installations. To accommodate thicker walls use a Wall Thimble Extension. ll HT eiling Supports now feature an integrated ttic Insulation Shield. These must be used in all installations that pass through an attic, regardless of whether the attic is insulated or not. If a chimney is fully enclosed within a chase, an attic insulation shield is not required. Note: For Multi-Story applications, an ttic Insulation Shield must be purchased separately. Firestop Radiation Shield must be used when a chimney passes through a floor or ceiling without a ceiling support. The Roof Radiation Shield is only required when the chimney is enclosed in a chase within the attic space. It is not required when the chimney is unenclosed in the attic space. himney ap Extended Roof racket Storm ollar Flashing Roof Radiation Shield Elbow Strap Elbow ttic Insulation Shield Firestop Radiation Shield 15 9 djustable Wall Strap Second Floor hase eiling Support DVL/Duralack himney dapter Duralack Stovepipe or DVL lose learance onnector Stovepipe Stove dapter Through-The-Wall athedral eiling w/support ox DuraVent 62
21 DuraPlus HT ll-fuel himney himney Pipe Ø Designed for appliances tested and listed for use in anada with wood stoves, fireplaces, furnaces, boilers, stoves, ranges, water heaters, or other appliances fueled by wood, oil, coal, or gas. To calculate the installed section of DuraPlus HT chimney pipe, subtract from each section of chimney pipe. DuraPlus HT pipe lengths are available with additional protective carton foam for shipping. vailable items have stock # s ending with (F). Length Ø SIZE 6 8 ORDER # STOK # ORDER # STOK # ORDER # STOK # HT HT HT HT HT HT HT HT HT HT HT HT HT HT HT HT-36F HT HT HT HT-8F Elbow Kit *updated order numbers* Kit includes: Two Elbows and one Elbow Strap. Use for offsets around obstructions such as rafters, ridgepoles, or joists. May have two pairs of elbows, if needed. Elbows swivel 360 at base (angles are not adjustable). pair of elbows is required to return an offset chimney back to vertical. Made of stainless steel. (Note: 5 elbows are only allowed in anada. The maximum angle allowed in the U.S. is 30. Refer to installation instructions) ORDER # 6HT-E15K HT-E15K 8HT-E15K STOK # ORDER # 6HT-E30K HT-E30K 8HT-E30K STOK # ORDER # 6HT-E5K HT-E5K 8HT-E5K STOK # DuraVent
22 DuraPlus HT ll-fuel himney Reduced learance Square eiling Support ox Use with flat, vaulted, or cathedral ceilings. Square eiling Support ox is painted black. 12 x 12 framing dimension permits installation within narrow joist spaces. ox will carry to 0 of DuraPlus HT himney, and doubles as an ttic Insulation Shield. Starter Section built in. Reduces the usual 2 clearance (per side) down to a 1 clearance (per side) for the 6 diameter only. vailable in 2 or 36 box height. omes with trim, insulation collar, and DVL himney dapter. Refer to eiling Pitch table as listed with Square eiling Support ox to determine size of support box needed. vailable for use with 6 chimney only. SIZE ORDER # 6HT-S2R 6HT-S36R STOK # ombustion ir Square eiling Support ox *updated illustration* Use with ombustion ir System (S) components. Delivers outdoor combustion air to the appliance without the need for an additional penetration of the building envelope. Supports up to 0 of DuraPlus HT himney. Support box also doubles as an ttic Insulation Shield. omes with trim, and insulation collar. Stovepipe adapter is already built-in. vailable in 2 inch or 36 inch length. Use with flat, vaulted, or cathedral ceilings. Patent-pending SIZE ORDER # 6S-S2HT 8S-S2HT STOK # ORDER # 6S-S36HT 8S-S36HT STOK # Universal Support ox Rails 18 ttach to ouside of Square eiling Support ox to provide level, temporary support. This enables an installer to easily fasten the box in place without the need for another pair of hands. Simplifies installation. One size fits 6,, 8 DuraPlus HT support boxes. SIZE 6-8 ORDER # 6HT-SRU STOK # DuraVent
23 ombustion ir System Triple-wall stovepipe system designed to provide air for combustion through its components. UL 1 and UL S61. DVL Double-wall interior close clearance stovepipe for connecting woodstoves to chimney. UL S61. Duralack Single-wall interior stovepipe for connecting woodstoves to chimney.
24 Stovepipe ombustion ir System ombustion ir Wall Thimble Provides connection between DuraTech or DuraPlus HT chimney systems and the ombustion ir Stovepipe. djusts to fit wall thicknesses from 5 1/2 to 10. Extends into room 6. Painted black. Patent-pending. Ø DURTEH SIZE ORDER # 6S-WTDT 8S-WTDT STOK # DURPLUS HT SIZE ORDER # 6S-WTHT 8S-WTHT STOK # ombustion ir eiling Support w/ ollar *updated illustration* Provides connection between DuraTech or DuraPlus HT chimney systems and the ombustion ir Stovepipe. vailable in 2 or 36 heights, the eiling Support ox acts as an attic insulation shield with the addition of a Storm ollar. eiling Support extends a total of -1/2 below the ceiling. lack. DURTEH SIZE ORDER # 6S-S2DT 6S-S36DT 8S-S2DT 8S-S36DT STOK # DURPLUS HT SIZE ORDER # 6S-S2HT 6S-S36HT 8S-S2HT 8S-S36HT STOK # DuraVent 90
25 PelletVent Pro iofuel venting system. UL 61, UL S609, and UL/ORD 1.
26 PelletVent Pro iofuel himney Typical Installations *updated key* 16 8 Pellet Insert athedral eiling Stove Installation Installation Key 1 Vertical ap 10 Horizontal ap 2 Storm ollar 11 Wall Thimble 3 Flashing 12 eiling Support Firestop Spacer athedral eiling Support ox 13 Tee w/ lean-out Tee ap 5 Straight Length Pipe 1 Wall Strap 6 5 Elbow 15 ttic Insulation Shield ppliance dapter 16 Prairie Termination ap 8 Flex Length 1 S djustable Wall hannel 9 90 Elbow 16 Refer to our Typical Venting Installation drawings to select the appropriate component parts for your installation. The inner pipe diameter should match the outlet size of the appliance. For installations that require vent and the appliance has a 3 outlet, use an Increaser dapter 3 -. heck the appliance manufacturer's installation instructions to confirm which types of vent configurations are permitted (i.e. horizontal, vertical, chimney reline, etc.). lso, check for any venting restrictions such as maximum horizontal run, minimum and maximum vertical rise, maximum offset, etc. e fire safe! Maintain the minimum clearances (air-space) between the vent pipe and nearby combustibles, as specified in the appliance manufacturer's installation instructions. Use proper support and bracing. Follow local building codes and have your venting system inspected Round Horizontal ap Elbow Wall Strap Straight Length Pipe Masonry himney Relining ttic Offset Tee with lean-out Tee ap 9 Wall Thimble ppliance dapter Through-The-Wall Vertical Rise Through-The-Wall 111 DuraVent
27 PelletVent Pro iofuel himney Male Flex dapter Use to connect ioflex to PelletVent Pro when relining a masonry chimney. Only approved for use with ioflex. SIZE ORDER # STOK # 3 3PVP-DFM PVP-DFM ppliance dapter Use to attach to appliance outlet allowing for easy pipe connection. Seal adapter to appliance with high temperature sealant. 3⅜ 3¾ SIZE ORDER # STOK # SIZE STOK # 3 3PVP-D PVP-D LK 3PVP-D LK PVP-D Quick Release dapter Use to attach to appliance outlet allowing for easy pipe connection. Features an adjustable hose clamp and gasket to form a tight seal. The hose clamp can be loosened and tightened as needed to disconnect and connect the vent to the appliance. SIZE ORDER # STOK # - 6 3PVP-DS /8-8 PVP-DS /8 Harman dapter *new product offering* Use to provide a secure, tight fit to the exhaust outlet on any Harman Pellet Stove. Seal with high temperature silicone sealant to insure a tight connection. SIZE ORDER # STOK # 3 3PVP-DH Harman dapter Increaser *new product offering* Use to increase vent diameters. Specifically designed for Harman Pellet Stoves. SIZE ORDER # STOK # 3 3PVP-XDH DuraVent
28 DuraLiner Insulated, double-wall masonry relining. UL 1 and UL S635.
29 DuraLiner himney Relining Spacer Use to maintain a 1 clearance with flex sections of DuraLiner. 3¼ SIZE ORDER # STOK # 6 OVL 6DLR-S OVL 8DLR-S djustable Sleeve Use for rear stove exits. Sleeve adjusts from to 12. 8½ to 12 SIZE ORDER # STOK # 6 6DLR-S DLR-S Masonry Thimble w/ Slip onnector ¼ Use to penetrate masonry chimney to allow connection of Duralack or DVL to DuraLiner. dapter must be used to attach the connector pipe to the masonry thimble. SIZE ORDER # STOK # 5 5DLR-MTS DLR-MTS DLR-MTS Wall Pass Through *updated illustration* Use to connect to a DuraLiner tee. Transitions DuraLiner through a masonry chimney and a combustible wall. llows the connection of Duralack pipe when used with the appropriate adapter. DVL black pipe will connect directly to the Wall Pass Through. SIZE ORDER # STOK # 6 6DLR-WPT DLR-WPT DuraVent
30 himney Relining DuraLiner Oval-To-Round Flex Pipe Use through damper and smoke shelf area. Use to connect from oval stove outlet to round DuraLiner. Use with DuraLiner ProMesh and ProFoil, where flex extends into clay liner, for zeroclearance applications. uilt from 1-ply construction, stainless steel. ¾ SIZE ORDER # STOK # 6 6DLR-36ORF DLR-60ORF DLR-36ORF DLR-60ORF Round-To-Oval Flex Pipe ¾ Use to connect a round stove outlet to oval DuraLiner. Use with DuraLiner ProMesh and ProFoil, where flex extends into clay liner, for zero-clearance applications. uilt from 30 stainless steel. SIZE ORDER # STOK # 6 6DLR-1ROF ompilation Nominal Pipe Size Ø Ø Ø 8 8DLR-1ROF /8 3 1/2 5/8 1/ /8 5 1/ /8 6 1/2 5/8 1/ /8 8 1/2 Round Rigid Pipe - 5" *updated description* Ø Use to reline masonry chimney with 0/0 clearance. Factoryinsulated. Twist-lock fittings and pre-drilled hole (one screw required). UL Listed for zero clearance between masonry and combustibles, plus zero clearance between liner and masonry. 30 stainless steel inner and aluminized steel outer. Note: to calculate the installed length of 5, 6, and 8 DuraLiner pipe subtract 1 ½ from each joint overlap of liner pipe sections. SIZE ORDER # STOK # 5 5DLR " 5DLR DLR " 5DLR DuraVent 136
31 DuraLiner himney Relining Round Rigid Pipe *updated description* Use to reline masonry chimney with 0/0 clearance. vailable in round 6 and 8 diameters in 12, 2, 36, and 8 lengths. Factory-insulated. uilt-in, pre-drilled fittings for riveting joints. 30 stainless steel inner and aluminized steel outer. Note: to calculate the installed length of 5, 6, and 8 DuraLiner pipe subtract 1 ½ from each joint overlap of liner pipe sections. SIZE ORDER # STOK # 6 6DLR DLR DLR DLR DLR DLR DLR DLR Oval Rigid Pipe *updated description* ¾ Use to reline masonry chimney with 0/0 clearance. vailable in oval 6 and 8 diameters; 12, 2, 36, and 8 lengths. Factory-insulated. uilt-in, pre-drilled fittings for riveting joints. 30 stainless steel inner and aluminized steel outer. Note: to calculate the installed length of 5, 6, and 8 DuraLiner pipe subtract 1 ½ from each joint overlap of liner pipe sections. SIZE ORDER # STOK # 6 6DLR-12O DLR-2O DLR-36O DLR-8O DLR-12O DLR-2O DLR-36O DLR-8O Twist-Lock ap Kit ap Storm ollar Support lamp ase Plate Use to terminates DuraLiner at the top of the masonry chimney. Pipe not included. Kit includes ase Plate, Support lamp, Storm ollar, and ap. SIZE ORDER # STOK # 5 5DLR-KV " 5DLR-KV DuraVent
32 DuraFlex Flexible stainless steel relining for masonry chimney. UL 1 and UL S635.
33 DuraFlex SW Stainless Steel Flexible Relining Factory-uilt Reline Kit *new product offering* Use as a relining system for factory-built chimneys to be used with solid-fuel appliances in the US. Relining is critical for performance and safety when a wood-burning insert is installed into an existing UL-12-listed fireplace. Kit includes: ap, Storm ollar, Support racket, Ventilation Disk, entering racket, DuraLiner 12" Length, Flex onnector, Flex Length (25' or 35'), djustable and, and Flex dapter. 6" SIZE 25' FLEX 35' FLEX ORDER # STOK # ORDER # STOK # DuraFlex Pro 6DFPRO-25KF DFPRO-35KF DuraFlex 30 6DF30-25KF DF30-35KF DuraFlex 316 6DF316-25KF DF316-35KF DuraFlex SW asic Kit Kit includes: DuraFlex SS Top Plate, DuraFlex SS ap, DuraFlex SS onnector, and DuraFlex SW length. Flex lengths available in 15, 20, 25, 30, and 35. SIZE 15 FLEX 20 FLEX 25 FLEX ORDER # STOK # ORDER # STOK # ORDER # STOK # 3 3DFSW-15K DFSW-20K DFSW-25K DFSW-15K DFSW-20K DFSW-25K DFSW-15K DFSW-20K DFSW-25K DFSW-15K DFSW-20K DFSW-25K DFSW-15K DFSW-20K DFSW-25K DFSW-15K DFSW-20K DFSW-25K DFSW-15K DFSW-20K DFSW-25K SIZE 30 FLEX 35 FLEX ORDER # STOK # ORDER # STOK # 3 3DFSW-30K DFSW-35K DFSW-30K DFSW-35K DFSW-30K DFSW-35K DFSW-30K DFSW-35K DFSW-30K DFSW-35K DFSW-30K DFSW-35K DFSW-30K DFSW-35K DuraVent
34 DuraFlex Pro Stainless Steel Flexible Relining DuraFlex Pro Top Plate/ap Kit *updated product offering* Kit includes: Top Plate with welded Storm ollar, and ap, plus DuraFlex SS onnector, and DuraFlex Pro length. Flex remains secured to the Storm ollar/top Plate when removing the cap section for inspections and cleaning. SIZE 20 FLEX 25 FLEX ORDER # STOK # ORDER # STOK # 3 3DFPRO-20VK DFPRO-25VK DFPRO-20VK DFPRO-25VK " DFPRO-25VK DFPRO-20VK DFPRO-25VK " DFPRO-25VK " DFPRO-25VK " DFPRO-25VK SIZE 30 FLEX 35 FLEX ORDER # STOK # ORDER # STOK # DFPRO-35VK DFPRO-30VK DFPRO-35VK " DFPRO-35VK DFPRO-30VK DFPRO-35VK " 6DFPRO-30VK DFPRO-35VK " DFPRO-35VK " DFPRO-35VK DuraFlex Pro Ovalized Top Plate/ap Kit *updated photo and description* Kit includes: Welded Top Plate with lamp, Rain ap with lamp, Oval to Round Insert dapter with lamp, and DuraFlex Pro length with the first feet ovalized. Flex remains secured to the Storm ollar/top Plate when removing the cap section for inspections and cleaning. 25 FLEX 35 FLEX SIZE ORDER # STOK # ORDER # STOK # 6 6DFPRO-25OVLVK DFPRO-35OVLVK DuraVent
35 Ventinox Welded, flexible relining for masonry chimney. UL 1 and UL S635.
36 himney Relining Ventinox 12 Typical Installations *updated installation key* Installation Key 1 Rain ap w/ Storm ollar 2 Top over Plate 3 Flex Length Tee with Removable Snout 5 Sleeve 6 Rigid Type Gas Vent or Rigid Pipe Length djustable Elbow 8 DuraFlex ppliance dapter 9 ottom Plate w/ ollar 10 ProFoil w/promesh or Thermix Gas Furnace Gas Stove Refer to our Typical Venting Installation drawings to select the appropriate component parts for your installation ap with Storm ollar Top over Plate 1 5 Fireplace Insert Open Fireplace Ventinox Flexible Length Sleeve DuraVent 1
37 DirectVent Pro Unitized, co-axial venting system for direct vent gas or propane stoves, and fireplaces.
38 DirectVent Pro Direct Vent Wall Thimble Provides a complete wall-pass-through and firestop. Use with Square Horizontal ap only. May be required in anada. Refer to the appliance manufacturer s installation instructions for requirements. SIZE ORDER # STOK # x DV-WT x 8 58DV-WT Wall Thimble - Small *updated dimensions* Provides a complete wall-pass-through and firestop. Use with Round Horizontal ap and Sconce ap only. May be required in anada. Refer to the appliance manufacturer s installation instructions for requirements. SIZE ORDER # STOK # x DV-WTS x 8 58DV-WTS Universal Wall Thimble Provides a complete wall-pass-through and interior firestop. Features an adjustable sleeve for an exact fit. Eliminates visible trim on exterior or wall near cap. Sized to fit all DuraVent DirectVent Pro s termination caps. SIZE ORDER # STOK # x DV-WTU x 8 58DV-WTU Wall Firestop For horizontal (through-wall) installations. Refer to the appliance manufacturer s installation instructions for requirements. SIZE ORDER # STOK # x DV-WFS x 8 58DV-WFS DuraVent
39 Direct Vent DirectVent Pro Low-Profile Termination ap D Use for vertical terminations only. heck the appliance manufacturer s instructions to determine which caps are approved for use with their appliance. vailable in aluminum and stainless steel (S). SIZE ORDER # STOK # D x DV-V x DV-V-S x 8 58DV-V x 8 58DV-V-S Extended Vertical Termination ap *updated dimensions* D Use in extremely cold climates. Similar to the Low Profile Termination ap but taller in overall height to separate the air intake vents from the exhaust area. Refer to the appliance manufacturer s installation instructions for requirements. vailable in aluminum. SIZE ORDER # STOK # D x DV-VE ¾ ¾ x 8 58DV-VE ¾ / luminum Flex Length Use 3 flex with the co-linear system and flex with onversion Kits. See DuraFlex L section for more information. Flexible.010 thick 2-ply aluminum. Pricing for luminum Flex Length are listed under DuraFlex L. SIZE LENGTH ORDER # STOK # DF DF Flex oupling Use to join flex liner sections together. Pricing for luminum Flex Length are listed under DuraFlex L. 3 SIZE ORDER # STOK # 3 3DF-F DF-F DuraVent 198
40 DirectVent Pro Direct Vent o-xial To o-linear ppliance onnector Use o-linear dapter for stoves with X co-axial outlets. Refer to appliance manufacturer s installation instructions for approval. Uses 3 aluminum flex for both intake and exhaust. D SIZE ONNETOR ORDER # STOK # D x STNDRD 6DV-GL x TRVIS INDUSTRIES 6DV-TL x VERMONT STINGS 6DV-VL himney Liner Termination Kit Kit includes: Termination onnector and Flashing. DirectVent Pro x Termination aps, 3 Flex, and o-linear Flex onnectors are sold separately. DirectVent Pro chimney liner termination kit must be tested and listed for each appliance. Refer to stove manufacturer s installation instructions. SIZE ORDER # STOK # 0 0 x DV-GK x DV-T ppliance dapter *updated description* ttaches to appliance outlet allowing pipe to easily connect or disconnect. Vermont astings adapter #268. SIZE ORDER # STOK # x DV-DP Monessen dapter llows the installer to attach DuraVent s DirectVent Pro x pipe to a Monessen x direct vent exhaust outlet. Twist lock with a crimped male end. SIZE ORDER # STOK # x DV-DM DuraVent
41 Type Gas Vent Type Gas Vent Type gas venting system. UL 1 and UL S605. DuraFlex L luminum flexible relining UL 1 & UL S635.
42 c-ul-us 1 System Duraonnect II Double-wall connector pipe, UL approved as a Type Gas Vent segment, for use in conditioned and unconditioned attics and crawl spaces. (Not to be enclosed and cannot penetrate through walls, floors, or ceilings.) DuraVent s Duraonnect II is known as the ontractor s hoice for its ease of installation and durability. Duraonnect II s heavy-duty construction features precision twistlock connection, which provides ease of assembly or disassembly without damage to the product. The double-wall flexible vent is certified as having the equivalent thermal properties as Type Gas Vent and can be used when a Type Gas Vent double-wall connector is required. Specifications Duraonnect II Materials and onstruction.010 Double-wall aluminum flex inner wall (two-ply.005 ),.018 galvalume outer wall, with twist-lock connections. learances 1 to combustibles. Diameters 3" - 6". Listings c-ul-us Listed to UL 1 and UL/ ORD-1 (MH1089). UL 1 & UL S635 System DuraFlex L n economical venting system used for relining masonry chimney for natural gas or liquid propane category I, draft hood equipped appliances, and appliances tested and listed to use Type Gas Vent for a wide range of applications, including: natural gas fireplaces, gas-fired furnaces, boilers, water heaters, and wall or space heating applications. Protects the masonry chimney from damaging effects of flue product condensation. DuraFlex L *updated* pplications DuraFlex L (DFL) aluminum flexible relining for masonry chimney. Use with natural gas or liquid propane category I, draft hood equipped appliances, and appliances tested and listed to use Type Gas Vent. pplications include: natural gas fireplaces, gas-fired furnaces, boilers, water heaters, and wall or space heating applications. Materials and onstruction 010 aluminum (2-ply of.005 ). learances 0 clearance to masonry. Diameters 3,, 5, 5 ½, 6,, and 8. Listings Listed to UL 1 and UL S DuraVent 20
43 Type Gas Vent DuraFlex L DuraFlex L - luminum Length Use with ategory I gas-burning appliances with draft hood. UL 1 aluminum liner. Flex lengths available in 25, 35, and 50. SIZE 25 FLEX 35 FLEX 50 FLEX ORDER # STOK # ORDER # STOK # ORDER # STOK # 3 3DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF DF oupler *new part* Use to connect DuraFlex L lengths to PolyPro. To be used in combustion air only. PPS-P may be used to secure connection. SIZE ORDER # STOK # 3 3DF-FP DF-FP Hanger racket *new part* Use to secure and hang DuraFlex L lengths from top of enclosure. To be used on combustion air only. Must be used with FT himney ap or FK Lining Kit. SIZE ORDER # STOK # 3 - DF-F DuraFlex L oupling Use to connect DuraFlex L lengths to appliance, type gas vent, or flex lengths. 3 SIZE ORDER # STOK # SIZE ORDER # STOK # 3 3DF-F DF-F DF-F DF-F DF-F DF-F ½ 55DF-F DuraVent
44 Stainless Steel Flexible Relining DuraFlex DuraFlex Insert dapter *new part* Use to connect the flex to an insert that has a flat surfaced outlet. SIZE ORDER # STOK # 3 3DFS-D DFS-D DFS-D DFS-D DFS-D DFS-D DFS-D DuraFlex SS onnector Use to connect DuraFlex SS length to an appliance, rigid length, or flex length. Drip-free connection. 1/8 SIZE ORDER # STOK # 3 3DFS-F DFS-F DFS-F DFS-F DFS-F DFS-F DFS-F DuraFlex SS Reducer Ø5 ½ Use to connect DuraFlex SS length to a 6 appliance. heck with the appliance manufacturer before reducing the vent size. May also be used to connect to stovepipe on a through masonry wall installations. 1/8 Ø6 SIZE ORDER # STOK # DFS-X DuraFlex SS Tee w/ ap Use to attach to DuraFlex SS length with a fast connect band. Removable branch connects tee body with an internal fast connect band " Tee has a 6" branch. SIZE ORDER # STOK # 3 3DFS-T ½ 3 1 DFS-T ½ 1 5 5DFS-T ½ 1 5 ½ 55DFS-T ½ DFS-T ½ 3 8 DFS-T ½ DFS-T DuraVent 16
45 FasNSeal & FasNSeal W2 Single-wall and double-wall special gas vent systems. UL 138 and UL S636. FasNSeal Flex Flexible chimney liner for special gas vent system. UL 138 and UL 1.
46 Specifications pplications FasNSeal and FasNSeal Flex is for use with natural gas or propane ategories II, III and IV appliances or anada s Type H Gas Vent Systems, having a maximum rated operating temperature of 80 F and a maximum positive pressure of 15 (FasNSeal Flex 6") water column. FasNSeal can be used on a wide range of applications, including: high efficiency gas boilers, furnaces, booster heaters, pool heaters, water heaters, unit heaters, or tankless water heaters. FasNSeal W2 is ideal for use on commercial applications such as: office buildings, medical facilities, condos, or multiple unit apartment complexes where there is the need for low clearances to combustibles. In residential applications, FasNSeal W2 is the perfect solution for running between floor joists or in walls. Materials and onstruction *updated materials* FasNSeal 3 : L : L : L FasNSeal Flex Single strip double layer super-ferritic stainless steel (totalling.010 ). FasNSeal W2 3 6 : L29- stainless steel.016 inner wall, stainless steel.016 outer wall. : L29- stainless steel.016 inner wall, stainless steel.02 outer wall : L29- stainless steel.019 inner wall, stainless steel.02 outer wall. 1 2 : L29- stainless steel.02 inner wall, stainless steel.02 outer wall. UL 138 and UL S636 Systems FasNSeal & FasNSeal W2 ll FasNSeal (single-wall) and FasNSeal W2 (double-wall) vent lengths and components feature patented built-in mechanical locking band and triple-lipped directional gaskets. ll pipes and components are engineered with smooth clean welds located 90 from mechanical locking bands. This construction feature allows for ease of installation. The ½ air space between the inner and outer wall on FasNSeal W2 helps to reduce the clearance to combustibles in addition to creating a heat shield for additional safety. ll FasNSeal components which come in contact with exhaust gases and condensates are now silicone free. This important design and manufacturing feature greatly reduces the chances of system breakdown and failure. The main problems with silicone are there are too many adhesion factors which are very difficult to control and the process of binding similar materials with an epoxy, which can weaken the bond over time. Welded seams ensure a leak-free product that is meant to last. FasNSeal Flex Made from super-ferritic stainless steel. orrosion resistant. Manufactured with a sure-seal locking seam for superior strength and flexibility. The smooth inner-wall provides for no output reduction, allowing for full appliance efficiency, ease of cleaning and regular maintenance. The smooth inner wall optimizes gas flow, minimizes back pressure, and facilitates condensate management. Only flexible chimney liner listed to UL 138 standard. Diameters FasNSeal (single- and double-wall) 3-2 FasNSeal Flex 3-12 Listings FasNSeal (single- and double-wall) UL Listed to UL 138 and UL S636. FasNSeal Flex UL Listed to UL 138 and UL 1 and UL S DuraVent
47 D 3. USE NON-OMUSTILE HNGER EVERY SIX (6) FEET OF HORIZONTL RUN.. USE FIRE-RTED FIRESTOPS WHEN PENETRTING FIRE-RTED WLLS ND/OR EILINGS. 5. REFER TO THE FSNSEL INSTLLTION INSTRUTIONS FOR DDITIONL REQUIREMENTS. NOTE: Every effort has been made to ssure the accuracy of this information. Dura-Vent cannot guarantee ccuracy and will not be held liable for Errors or omissions. NOTES: 1. LL WORKMNSHIP MUST MEET ND/OR EXEED LL JURISDITIONL REQUIREMENTS. 2. INSTLL WLL RKET EVERY TWELVE (12) FEET OF VERTIL RUN X 2X X X X ITEM REVISION HISTORY ZONE REV DESRIPTION DTE PPROVED DRWN W. YOUNG 9/2/2010 HEKED Q MFG PPROVED QTY USTOMER # PRTS LIST PRT NUMER DESRIPTION FS-E W FS-SWDW W2-VL8-L W W2-VL W W W2-VL8-L W W2-VL8-L W W FS-DWSW FSS FSL9 SIZE THIRD NGLE PROJETION DWG NO 1 SHEET 1 OF 1 USTOM 6 in. length 8 in. length 10 in. length NOTIE: THIS DOUMENT ONTINS PROPRIETRY INFORMTION ND IT SHLL NOT E USED, REPRODUED, OR ITS ONTENTS DISLOSED, IN WHOLE OR IN PRT, WITHOUT THE EXPRESS WRITTEN ONSENT OF PROTEH SYSTEMS DIVISION OF M & G DUR-VENT OMPNY, IN. REV D FasNSeal Special Gas Vent ommercial pplications ommercial projects may require custom parts and unique system designs. DuraVent offers complete project assistance: oilers are: erco MK. 2.0 (3X) M & G Engineering Services: Personalized system design services offer comprehensive D submittal drawing and complete bills of materials. ustom Parts: If your project requires innovative solutions, contact DuraVent for custom parts that meet your specific project needs. FasNSeal W2: FasNSeal W2 is the ideal choice for commercial applications where there is a need for low clearances to combustibles. Up to 2 Vent Diameters: Many commercial applications require large diameter systems due to the units size and output. Large diameters are available in single and double wall, featuring FasNSeal s triple lipped directional gaskets and built-in locking band which provides a safe and convenient installation. learances hart *updated table* FasNSeal Rated Operating Temperatures Enclosed Unenclosed Horizontal Vertical Horizontal Vertical F \ 90 0" 0" (anada Only) 300 F / 19 Sides: 8 /203.2mm 1 / 25.mm Top: 12 /30.8mm 80 F / mm ottom: /101.6mm 3 / 6.2mm 1 / 25.mm 19 F / 90 0" 0" (anada Only) 300 F \ 19 3 / 6.2mm 3 / 6.2mm Noncombustible Enclosure 80 F \ 29 3 / 6.2mm 3 / 6.2mm FasNSeal W2 Rated Operating Temperatures Enclosed Unenclosed Horizontal Vertical Horizontal Vertical 19 F (anada Only) 0" 0" 0" 0" F F 6" F 6" F (anada Only) 0" 0" 0" 0" F F 6" F 6" Rated Operating Temperature of 300 F = Max Flue Gas Temperature of 35 F Rated Operating Temperature of 80 F = Max Flue Gas Temperature of 550 F 235 DuraVent
48 FasNSeal Special Gas Vent Female Flex dapter Use to connect FasNSeal Flex to FasNSeal rigid Vent Pipe at the top of the system. Ø Ø SIZE ORDER # STOK # 3 FSSMF FSSMF FSSMF FSSMF FSSMF SIZE ORDER # STOK # 8" FSSMF " FSSMF " FSSMF FSSMF Test Port *updated order #s* Use to test for proper appliance operation without penetrating the vent wall. Easy access to perform flue gas analysis. More options available, see Universal dapter w/test Port in FasNSeal ppliance dapter section. 5⅞" SIZE ORDER # STOK # SIZE ORDER # STOK # 3 FSTP FSTP FSTP FSTP FSTP FSTP FSTP " FSTP " FSTP " FSTP FSTP Elbow Use to go from horizontal to vertical runs or vertical to horizontal runs. Use to turn vent 90. SIZE ORDER # STOK # 3 FSEL FSEL FSEL FSEL FSEL FSEL " FSEL " FSEL SIZE ORDER # STOK # 12 FSEL FSEL FSEL FSEL FSEL FSEL FSEL DuraVent
49 FasNSeal Special Gas Vent Tall one Roof Jack Use as a heat shield within the flashing. Maintains center-line and clearance to combustibles. Use with Tall one Flashings. 18 SIZE ORDER # STOK # 3 FSRJ " " FSRJ " 5" FSRJ " 6" FSRJ " " FSRJ " 8" FSRJ " SIZE ORDER # STOK # 9" FSRJ " 10" FSRJ " 12" FSRJ " 1" FSRJ " 16" FSRJ " Tall one Flashing *updated description* 12 Use to create a weather-tight penetration where the vent passes through a flat roof. Roof Jack and Storm ollar required. SIZE ORDER # STOK # 3 FSF " FSF " FSF " FSF " FSF " FSF SIZE ORDER # STOK # 9" FSF " FSF " FSF " FSF " FSF Tapered Increaser Use to increase vent diameter. reates a smooth transition for an undisruptive flow. vailable in custom size combinations. SIZE ORDER # STOK # 3 x FS030TI x 5 FS005TI Eccentric Increaser Use to transition to a larger diameter pipe. Prevents condensate puddling when used on horizontal runs. ids in reducing formation of condensates. Maximum 10 difference between diameter increase size on both sizes. vailable in custom size combinations. SIZE ORDER # STOK # 3 x FS030EI x 5 FS005EI DuraVent
50 Special Gas Vent FasNSeal Stepped Increaser Use to increase vent diameter when space constraints are an issue. vailable in custom size combinations. 6 SIZE ORDER # STOK # 3 x FS3I x 5 FS5I Tapered Reducer Use to reduce vent diameter. reates a smooth transition for an undisruptive flow. Maximum 10 diameter increase size on both sizes. vailable in custom size combinations. SIZE ORDER # STOK # x 3 FS003TR " x FS050TR " Stepped Reducer Use to reduce vent diameter when space constraints are an issue. vailable in custom size combinations. 6 SIZE ORDER # STOK # x 3 FS3R x FS5R Double-Wall dapter *updated description* Use to transition from a single-wall pipe to double-wall pipe. To transition from double-wall to single-wall, please reference single-wall adapter available in single-wall FasNSeal section. Ø SIZE ORDER # STOK # 3 FS-SWDW SIZE ORDER # STOK # 12 FS-SWDW FS-SWDW " FS-SWDW FS-SWDW " FS-SWDW FS-SWDW FS-SWDW " FS-SWDW FS-SWDW FS-SWDW FS-SWDW FS-SWDW FS-SWDW FS-SWDW DuraVent 252
51 Special Gas Vent FasNSeal W2 Single-Wall dapter *updated description* Use to transition from double-wall pipe to single-wall pipe. To transition from single-wall to double-wall, please reference double-wall adapter available in single-wall FasNSeal section. SIZE ORDER # STOK # SIZE ORDER # STOK # 3 FS-DWSW FS-DWSW FS-DWSW FS-DWSW FS-DWSW FS-DWSW FS-DWSW " FS-DWSW " FS-DWSW " FS-DWSW FS-DWSW Firestop/Flat Flashing Use when penetrating floor levels. When installing double-wall with this component use 1 larger diameter, (e.g. 10 vent system, use 11 size). SIZE ORDER # STOK # SIZE ORDER # STOK # FSFS FSFS FSFS " FSFS FSFS FSFS FSFS FSFS FSFS FSFS " FSFS FSFS " FSFS FSFS FSFS FSFS " FSFS FSFS " FSFS FSFS " FSFS Wall racket Use to support vent pipe or tee sections. Provides proper clearance to combustibles. When installing FasNSeal W2 with this component use 1 larger diameter, (e.g. 10 vent system, use 11 size). SIZE ORDER # STOK # " FSW SIZE ORDER # STOK # 11 FSW FSW FSW FSW FSW " FSW " FSW FSW FSW FSW " FSW FSW FSW DuraVent 26
52 Special Gas Vent FasNSeal W2 Storm ollar Use to create a weather tight seal between the pipe and flashing. When installing FasNSeal W2 with this component use 1 larger diameter, (e.g. 10 vent system, use 11 size). SIZE ORDER # STOK # FS FS FS " FS FS FS FS FS SIZE ORDER # STOK # 13" FS " FS " FS " FS " FS " FS " FS Variable Pitch Roof Flashing Use to create a weather-tight penetration where the vent pipe passes through the roof. Storm ollar required. When ordering Flashings for FasNSeal W2 product the flashing diameter and vent diameter are the same. ie. W requires a FSVPF10. ccommodates flat to 9/12 roof pitch. SIZE ORDER # STOK # FSVPF FSVPF FSVPF " FSVPF FSVPF FSVPF FSVPF SIZE ORDER # STOK # 12 FSVPF " FSVPF " FSVPF " FSVPF " FSVPF " FSVPF " FSVPF Tall one Flashing *updated description* Use to create a weather-tight penetration where the vent pipe passes through a flat roof. Storm ollar required. When ordering Flashings for FasNSeal W2 product the flashing diameter and vent diameter are the same. ie. W requires a FSVPF SIZE ORDER # STOK # 3 FSF " FSF " FSF " FSF " FSF " FSF SIZE ORDER # STOK # 9" FSF " FSF " FSF " FSF " FSF DuraVent 266
53 FasNSeal dapters Universal ppliance dapter SIZE ORDER # STOK # 3 FSU FSU FSU FSU FSU FSU SIZE ORDER # STOK # 9 FSU FSU FSU FSU FSU Universal ppliance dapter w/ Test Port *updated order #s* 6¼" SIZE ORDER # STOK # 3 FSUTP FSUTP FSUTP FSUTP FSUTP FSUTP SIZE ORDER # STOK # 9 FSUTP FSUTP FSUTP FSUTP FSUTP Universal ppliance dapter w/ ondensate Drain SIZE ORDER # STOK # 3 FSUD FSUD Universal ppliance dapter w/ ondensate Drain and ack Flow Preventer SIZE ORDER # STOK # FSUDFP DuraVent
54 dapters FasNSeal W2 ppliance dapter SIZE ORDER # STOK # 3 W W W W W W W W W W W W2 ppliance dapter w/ Test Port 6¼" SIZE ORDER # STOK # 3" W2-TP " W2-TP " W2-TP " W2-TP " W2-TP " W2-TP SIZE ORDER # STOK # 9" W2-TP " W2-TP " W2-TP " W2-TP " W2-TP Metric Male ppliance dapters *updated offering* SIZE ORDER # STOK # 19 mm FS-19-6F mm FS-158-6F mm FS-19-8F mm FS F De Dietrich GT Series ppliance dapter SIZE ORDER # STOK # FSU FSU FSU FSU DuraVent 22
55 PolyPro Polypropylene venting products for high-efficiency condensing appliance installations. hloride free, environmentally safe. Listed to UL-S636.
56 Specifications pplications PolyPro is a polypropylene vent pipe for use with NSI ategory II and IV gas-burning appliances, including highefficiency water heaters, condensing boilers and warm air furnaces. PolyPro is listed by Intertek to the UL S636 standard in anada as a lass II, II and II vent system suitable for exhaust temperatures up to 230 F / 110, and a maximum positive pressure of 15 in-w.c. Materials and onstruction *updated* Rigid pipe constructed of 2.2mm (minimum) thick polypropylene. Flex is double-wall polypropylene. EPDM or optional Viton Gaskets learances 0 clearance to combustibles for exhaust temperatures up to 19 F / 90, and 0 clearance for vertical installations up to exhaust temperatures of 230 F / 110 and ¼ / 6mm clearance to combustibles for horizontal installations at exhaust temperatures up to 230 F / 110. PolyPro concentric vent system components, including concentric Horizontal Termination and Vertical Termination, are listed at 0 clearance to combustibles for exhaust temperatures up to 230 F / 110. Diameters 2" (60mm), 3" (80mm), " (100mm), 5" (130mm), 6" (150mm), and 8" (200mm). PolyPro *updated* PolyPro and PV/PV: PV pipes are commonly used for venting water heaters, condensing boilers and warm air furnaces, yet PV was never designed for such use. n environmentally safe and engineered alternative for condensing gas appliances is PolyPro. Engineered for venting, it is 100% recyclable; contains no toxic or carcinogenic materials, chlorides, or heavy metals; and is also easier and faster to install then PV, saving the contractor time and money. PolyPro does not release hazardous gases during combustion and has been used safely throughout Europe since the early 1990s. Polypropylene has a higher operating temperature limit of 230 F/110 (PV is 19 F/65 max and PV is 19 F/90 ). PolyPro is engineered with a corrosion-free, condensation management system. PolyPro Flex PolyPro Flex through Vent as a hase: Retrofit venting for new, high-efficiency appliances. When replacing a mid-efficiency appliance with a new condensing 90+ appliance, you can use the existing vent (any brand) as a chase for the new appliance with PolyPro. The perfect solution for utilizing the Vent already in place, use the convenient pull cone to insert double-wall PolyPro Flex through the Vent pipe and terminate in either a two pipe or single pipe system. t the other end is the unique Vent/PolyPro Support ap, allowing for the connection of flex to rigid PolyPro lengths and elbows to finish the installation. Terminations DuraVent s concentric PolyPro vertical terminations are lab tested to handle harsh weather and remain icicle free in freezing temperatures. ir circulation and weather conditions like rain, wind and ice have the potential to reduce the efficiency of a unit's performance and the operation of its venting system. Listings Listed with the appliance in the US and anada, check with appliance manufacturer. Intertek / ETL listed to UL S636 Listed as a lass II, II, and II vent system. Tested and listed by a major testing agency, such as S. PolyPro complies with LEED credit IEQc.1 on VO limits. PolyPro is approved by the Massachusetts Plumbers oard. pproval code G
57 PolyPro Single-Wall Venting System lack UV Resistant Tee Use as a termination. Made of UV resistant polypropylene. Gasket not included. Order ird Guard Screen to protect opening. SIZE ORDER # STOK # 2 60mm 2PPS-T mm 3 80mm 3PPS-T mm 100mm PPS-T mm lack UV Resistant Termination Tee *new product offering* Use as a termination. Manufactured with two female ends to accept ird Screen on both ends. Use bird screen to protect openings. Made of UV resistant polypropylene. SIZE ORDER # STOK # 6 150mm 6PPS-TT lack Wall Plate Use to trim wall penetration. Painted black metal with gasket. SIZE ORDER # STOK # 2 60mm 2PPS-WP mm 3PPS-WP mm PPS-WP lack Wall Plate for Twin Pipes Use to trim wall penetration when using two pipes. Painted black metal with gasket. SIZE ORDER # STOK # 2 60mm 2PPS-WPT mm 11 /10" 29mm 8 ½" 216mm 3 80mm 3PPS-WPT mm 11 /10" 29mm 8 ½" 216mm 100mm PPS-WPT mm 12 /10" 323mm 8 ½" 216mm Tee with Drain ap Use to manage condensates at the bottom of a vertical run. SIZE ORDER # STOK # SIZE ORDER # STOK # 2 60mm 2PPS-TD mm 5PPS-TD mm 3PPS-TD mm 6PPS-TD mm PPS-TD mm 8PPS-TD DuraVent
58 Single-Wall Venting System PolyPro Increaser Use to transition the vent system to a larger diameter. Install in vertical orientation. SIZE ORDER # STOK # 2" - 3" 60-80mm 2PPS-X mm mm 3PPS-X mm mm PPS-X mm mm 5PPS-X mm mm 6PPS-X ¾" 15mm ppliance dapter for PV Pipe Use to connect PolyPro vent system to an appliance outlet. Has a double female adapter. One end accepts PV male pipe and the other accepts PolyPro male pipe. No adapter connector and/or locking band required. SIZE ORDER # STOK # 3 80mm 3PPS-D-M mm PPS-D-M ppliance dapter for PV oupler *updated description* Use to adapt rigid PolyPro pipe length to the inside of the PV/ PV coupler or other plastic appliance outlet. Must be used with dapter onnector for flue gas. SIZE ORDER # STOK # SIZE ORDER # STOK # 2 60mm 2PPS-D mm PPS-D mm 3PPS-D Female ppliance dapter Use to connect PolyPro to a nominal sized pipe with a smooth male end outlet. No adapter connector and/or locking band required. Hose clamps on both ends. SIZE ORDER # STOK # 6 150mm FSU6-6PP /16" 151mm 6" 150mm 5" 130mm 8 200mm FSU3-3PP /16" 199mm 8" 200mm 5" 130mm DuraVent 290
59 Single-Wall Venting System PolyPro Increaser Use to transition the vent system to a larger diameter. Install in vertical orientation. SIZE ORDER # STOK # 2" - 3" 60-80mm 2PPS-X mm mm 3PPS-X mm mm PPS-X mm mm 5PPS-X mm mm 6PPS-X ¾" 15mm ppliance dapter for PV Pipe *new name and description* Use to connect PolyPro vent system to an appliance outlet. Has a double female adapter. One end accepts PV male pipe and the other accepts PolyPro male pipe. No adapter connector and/or locking band required. SIZE ORDER # STOK # 3 80mm 3PPS-D-M mm PPS-D-M ppliance dapter for PV oupler *new name and description* Use to adapt rigid PolyPro pipe length to PV/PV coupler or other plastic appliance outlet. Must be used with dapter onnector for flue gas. SIZE ORDER # STOK # SIZE ORDER # STOK # 2 60mm 2PPS-D mm PPS-D mm 3PPS-D Female ppliance dapter *new name and description* Use to connect PolyPro to a nominal sized pipe with a smooth male end outlet. No adapter connector and/or locking band required. Hose clamps on both ends. SIZE ORDER # STOK # 6 150mm FSU6-6PP /16" 151mm 6" 150mm 5" 130mm 8 200mm FSU3-3PP /16" 199mm 8" 200mm 5" 130mm DuraVent 290
60 PolyPro Single-Wall Venting System Male PV ppliance dapter Use to connect PolyPro vent system to a standard stainless steel appliance outlet equipped with an integrated hose clamp and gasket. Must be used with dapter onnector for flue gas, unless a clamp is supplied on the appliance outlet. Same O.D. as PV. SIZE ORDER # STOK # 3 80mm 3PPS-03PVM-3PPF /16" 81mm 3 ½" 89mm 6 13/16" 13mm 100mm PPS-0PVM-PPF " 102mm ½" 11mm 6 13/16" 13mm 6 150mm 6PPS-06PVM-6PPF /16" 132mm 5 9/16" 11mm 6 13/16" 13mm 8 200mm 8PPS-08PVM-8PPF " 152mm 6 5/8" 168mm 6 15/16" 16mm Female PV ppliance dapter *updated description* ccepts PolyPro Fits Over PV Fits Inside PV Use to directly connect PolyPro to a male PV Pipe appliance outlet. Seals on the O.D. of the PV pipe and has a clamp. No adapter connector and/or locking band required. SIZE ORDER # STOK # 5 130mm 5PPS-05PVF-5PPF " 130mm 5 11/16" 1mm 6 150mm 6PPS-06PVF-6PPF /16" 151mm 6 11/16" 10mm 8 200mm 8PPS-08PVF-8PPF /16" 132mm /8" 200mm FasNSeal dapter Use to transition from FasNSeal vent system to PolyPro vent system. an be used as an appliance adapter or inline. No locking band required. SIZE ORDER # STOK # 3 80mm FS-03M-2PPF /8" 60mm 3" 6mm 6 1/8" 156mm 3 80mm FS-03M-3PPF /8" 9mm 3" 6mm 5 15/16" 151mm 100mm FS-0M-PPF " 100mm " 100mm 5 15/16" 151mm 5 130mm FS-05M-5PPF /16" 132mm 5" 130mm 5 15/16" 151mm 6 150mm FS-06M-6PPF /16" 151mm 6" 150mm 6" 150mm 18mm FS-0M-6PPF /8" 156mm 6 5/16" 160mm " 18mm 8 200mm FS-08M-8PPF " 200mm 8" 200mm 6" 150mm PolyPro to FasNSeal dapter Use to transition from PolyPro vent system to FasNSeal vent system or to connect a metric appliance to FasNSeal. an be used as an appliance adapter or inline. Locking band required for 3" - " diameters, recommended for 5" - 8" diameters. SIZE ORDER # STOK # 3 80mm 3PPS-DM-03FNSF " 80mm 3 1/8" 9mm 3 13/16" 9mm 100mm PPS-DM-0FNSF " 100mm 3 1 5/16" 99mm 5 15/16" 151mm 5 130mm 5PPS-DM-05FNSF " 130mm 5 1/8" 131mm 5 15/16" 151mm 6 150mm 6PPS-DM-06FNSF " 150mm 5 15/16" 151mm " 18mm 8 200mm 8PPS-DM-08FNSF " 200mm /8" 199mm " 18mm 291 DuraVent
61 PolyPro Single-Wall Venting System Male PV ppliance dapter *new name and description* Use to connect PolyPro vent system to a standard stainless steel appliance outlet equipped with an integrated hose clamp and gasket. Must be used with dapter onnector for flue gas, unless a clamp is supplied on the appliance outlet. Same O.D. as PV. SIZE ORDER # STOK # 3 80mm 3PPS-03PVM-3PPF /16" 81mm 3 ½" 89mm 6 13/16" 13mm 100mm PPS-0PVM-PPF " 102mm ½" 11mm 6 13/16" 13mm 6 150mm 6PPS-06PVM-6PPF /16" 132mm 5 9/16" 11mm 6 13/16" 13mm 8 200mm 8PPS-08PVM-8PPF " 152mm 6 5/8" 168mm 6 15/16" 16mm Female PV ppliance dapter *new name and description* ccepts PolyPro Fits Over PV Fits Inside PV Use to connect PolyPro to a male PV Pipe appliance outlet. No adapter connector and/or locking band required. SIZE ORDER # STOK # 5 130mm 5PPS-05PVF-5PPF " 130mm 5 11/16" 1mm 6 150mm 6PPS-06PVF-6PPF /16" 151mm 6 11/16" 10mm 8 200mm 8PPS-08PVF-8PPF /16" 132mm /8" 200mm FasNSeal dapter *new name and description* Use to transition from FasNSeal vent system to PolyPro vent system. an be used as an appliance adapter or inline. No locking band required. SIZE ORDER # STOK # 3 80mm FS-03M-2PPF /8" 60mm 3" 6mm 6 1/8" 156mm 3 80mm FS-03M-3PPF /8" 9mm 3" 6mm 5 15/16" 151mm 100mm FS-0M-PPF " 100mm " 100mm 5 15/16" 151mm 5 130mm FS-05M-5PPF /16" 132mm 5" 130mm 5 15/16" 151mm 6 150mm FS-06M-6PPF /16" 151mm 6" 150mm 6" 150mm 18mm FS-0M-6PPF /8" 156mm 6 5/16" 160mm " 18mm 8 200mm FS-08M-8PPF " 200mm 8" 200mm 6" 150mm PolyPro to FasNSeal dapter *new name and description* Use to transition from PolyPro vent system to FasNSeal vent system or to connect a metric appliance to FasNSeal. an be used as an appliance adapter or inline. Locking band required for 3" - " diameters, recommended for 5" - 8" diameters. SIZE ORDER # STOK # 3 80mm 3PPS-DM-03FNSF " 80mm 3 1/8" 9mm 3 13/16" 9mm 100mm PPS-DM-0FNSF " 100mm 3 1 5/16" 99mm 5 15/16" 151mm 5 130mm 5PPS-DM-05FNSF " 130mm 5 1/8" 131mm 5 15/16" 151mm 6 150mm 6PPS-DM-06FNSF " 150mm 5 15/16" 151mm " 18mm 8 200mm 8PPS-DM-08FNSF " 200mm /8" 199mm " 18mm 291 DuraVent
62 PPS-WSM Single-Wall Venting System PolyPro Wall Strap - metal Use to support for offsets, vertical and horizontal runs. Wall Strap legs can be rotated 360 to conceal screw. ccepts 1/ all-thread. vailable in galvanized or stainless steel metals. Supporting Wall Straps are required at least every 10 feet 3 meters for vertical vent pipe sections, and horizontal or sloped sections of vent pipe require one supporting Wall Strap for each pipe section. SIZE GLVNIZED ORDER # STOK # 2 60mm 2PPS-WSM /8" 92mm /8"" 12mm 3 80mm 3PPS-WSM mm mm 100mm PPS-WSM mm mm 5 130mm 5PPS-WSM mm mm 6 150mm 6PPS-WSM mm mm 8 200mm 8PPS-WSM mm mm SIZE STINLESS STEEL ORDER # STOK # 2 60mm 2PPS-WSM-SS /8" 92mm /8" 12mm 3 80mm 3PPS-WSM-SS mm mm 100mm PPS-WSM-SS mm mm 5 130mm 5PPS-WSM-SS mm mm 6 150mm 6PPS-WSM-SS mm mm 8 200mm 8PPS-WSM-SS mm mm Locking and Use to secure two sections of pipe together. Required to comply with UL-S636 listed installations for 2 to diamaters. Locking ands optional for 5 diameter. SIZE ORDER # STOK # SIZE ORDER # STOK # 2 60mm 2PPS-L mm PPS-L mm 3PPS-L mm 5PPS-L Locking and lamp *updated offering* Use to secure two sections of pipe together. Locking ands optional for 5-8" diameters. Use to secure two large diameter sections of PolyPro pipe together. Typically used in vertical installations. SIZE ORDER # STOK # 2 60mm 2PPS-L /8" 60mm 2 ½" 6mm 3 80mm 3PPS-L /8" 80mm 2 ½" 6mm 100mm PPS-L " 100mm 2 ½" 6mm 5 130mm 5PPS-L /8" 130mm mm 6 150mm 6PPS-L /8" 156mm mm 8 200mm 8PPS-L /8" 20mm mm DuraVent 292
63 PolyPro Single-Wall Venting System Vertical Termination ap Kit - oncentric Use for concentric vertical terminations. Includes 2 appliance adapters and co-linear adapter. lack or terra-cotta cap. UV resistant. SIZE LK ORDER # STOK # 2 x 60 x 100mm 2PPS-VK mm mm ¾" 121mm 3 x 5 80 x 125mm 3PPS-VK mm mm ¾" 121mm x x 150mm PPS-VK mm mm 5 ½" 10mm SIZE TERR-OTT ORDER # STOK # 2 x 60 x 100mm 2PPS-VK-T mm mm ¾" 121mm 3 x 5 80 x 125mm 3PPS-VK-T mm mm ¾" 121mm x x 150mm PPS-VK-T mm mm 5 ½" 10mm Horizontal Termination Kit - oncentric *updated description* MX LENGTH Use for concentric horizontal terminations. Includes 2 appliance adapters, white wall plate, white firestop, and co-linear adapter. White Termination with ird Guard Screen. UV resistant. Inner plate is 8 5/8 (220mm) square, outer plate is 9 /16 (20mm) square for all flue sizes. SIZE ORDER # STOK # mm 2PPS-HK ¾ 350mm ¾" 121mm 3 x mm 3PPS-HK mm ¾" 121mm x mm PPS-HK ¾ 350mm 5 ½" 10mm ird Guard Screen Use to protect venting system from birds and rodents. Position inside pipe in place of gasket. Stainless steel. Pack of 6. SIZE ORDER # STOK # SIZE ORDER # STOK # 2 60mm 2PPS-G mm PPS-G mm 3PPS-G " 150mm 6PPS-G EPDM Replacement Gasket Use as a replacement gasket for rigid PolyPro products. Pack of 12. SIZE ORDER # STOK # SIZE ORDER # # STOK # 2 60mm 2PPS-G mm 5PPS-G mm 3PPS-G mm 6PPS-G mm PPS-G mm 8PPS-G Viton Replacement Gasket Use as a gasket for oil fuel appliances. SIZE ORDER # STOK # SIZE ORDER # STOK # 2 60mm 2PPS-GV mm 5PPS-GV mm 3PPS-GV mm 6PPS-GV mm PPS-GV mm 8PPS-GV DuraVent
DuraPlus HTC. All-fuel, double-wall chimney system. ULC S629.
DuraPlus HTC ll-fuel, double-wall chimney system. ULC S629. Specifications pplications DuraPlus HTC is a double-wall, all-fuel chimney system for both the U.S. and Canada for use with wood stoves; fireplaces;
More informationPelletVent Pro. Biofuel venting system. UL 641, ULC S609, and ULC/ORD C441.
PelletVent Pro iofuel venting system. UL 641, ULC S609, and ULC/ORD C441. Specifications pplications PelletVent Pro is a venting system designed for stoves and inserts that use wood pellets and oil fuel.
More informationCVS. Venting System for Category II, III, and IV gas appliances. Listed to UL-1738 and ULC S636.
VS Venting System for ategory II, III, and IV gas appliances. Listed to UL-1738 and UL S636. PelletVent venting system. Listed to UL 641, UL S609, and UL/ORD 441. Unitized venting system for DirectVent
More informationDirectVent Pro CVS. Unitized, co-axial venting system for direct vent gas or propane stoves, and fireplaces.
DirectVent Pro Unitized, co-axial venting system for direct vent gas or propane stoves, and fireplaces. VS Venting System for ategory II, III, and IV gas appliances. Listed to UL-1738 and UL S636. Specifications
More informationCombustion Air System DVL. DuraBlack. Triple-wall stovepipe system designed to provide air for combustion through its components. ULC S641.
Combustion ir System Triple-wall stovepipe system designed to provide air for combustion through its components. ULC S641. DVL Double-wall interior close clearance stovepipe for connecting woodstoves to
More informationPelletVent Pro. Biofuel venting system. UL 641, ULC S609, and ULC/ORD C441.
PelletVent Pro iofuel venting system. UL 641, ULC S609, and ULC/ORD C441. Specifications Applications PelletVent Pro is a venting system designed for stoves and inserts that use wood pellets and oil fuel.
More informationPelletVent Pro. Biofuel venting system. UL 641, ULC S609, and ULC/ORD C441.
PelletVent Pro iofuel venting system. UL 641, ULC S609, and ULC/ORD C441. Specifications Applications PelletVent Pro is a venting system designed for stoves and inserts that use wood pellets and oil fuel.
More informationCombustion Air System DVL. DuraBlack. Triple-wall stovepipe system designed to provide air for combustion through its components. ULC S641.
System Triple-wall stovepipe system designed to provide air for combustion through its components. ULC S641. DVL Double-wall interior close clearance stovepipe for connecting woodstoves to chimney. ULC
More informationBring In the Fresh Air
ring In the Fresh Air ombustion Air System For DuraTech, DuraPlus HT and PelletVent Pro DuraVent s new, exclusive, patentpending DuraPro ombustion Air System Wall Thimble and eiling Support oxes is the
More informationPelletVent Multi-fuel venting system. UL 641.
PelletVent Multi-fuel venting system. UL 641. Specifications Applications PelletVent is designed for venting of pellet stoves and inserts. Consult appliance manual for additonal requirements. Materials
More informationPelletVent Pro horizontal Kit. PelletVent Pro. PelletVent Pro Vertical Kit - Cathedral. PelletVent Pro Pellet Chimney
PelletVent Pro horizontal Kit Kit includes: Round horizontal Cap, Wall Thimble, and Appliance Adapter. Pipe lengths not included. 4 Kit includes a 3-4 Appliance Adapter/Increaser, painted black. 3 3PVP-KHA
More informationVenting System For Pellet and Corn Stoves. PelletVent Pro. C o m p l e t e V e n t i n g S o l u t i o n s f o r t h e H e a r t h I n d u s t r y
Venting System For Pellet and Corn Stoves PelletVent Pro C o m p l e t e V e n t i n g S o l u t i o n s f o r t h e H e a r t h I n d u s t r y ii PelletVent Pro For Stoves Burning Pellets & Corn Simpson
More informationBy Bernard Dalsin Mfg. Co. Installation and Operating Instructions Read these instructions and keep them for future reference
By Bernard Dalsin Mfg. Co. 5205 208 th St Farmington MN 55024 L-VENT TYPE 3 "and 4" Factory-built venting system for wood pellet, corn or biomass and low-temperature gas or liquid fuel appliances Installation
More informationTechnical and Dimensional Data. Saf-T Vent SC Plus
Technical and Dimensional Data Saf-T Vent S Plus 3"/5" & 4"/7" oncentric Reduced learance Double Wall for Special Gas Vent and/or Sealed ombustion Systems lso For Venting Listed Gas or Oil Fired ppliances
More informationBDM Direct Vent systems are for use with direct vent gas fired appliances.
INSTALLATION INSTRUCTIONS Pro-Form DIRECT VENT SYSTEM Tested to ANSI Z21.88-2009 /CSA 2.33-2009 REPORT # 369-P-02b-6.5 Read through all venting and appliance instructions before beginning your installation.
More informationULC S636 System. PolyPro. PolyPro Flex. Terminations
PolyPro Polypropylene venting products for high-efficiency condensing appliance installations. Chloride free, environmentally safe. Listed to ULC-S636. Specifications pplications PolyPro is a polypropylene
More information5"x 8" DIRECT VENT INSTALLATION INSTRUCTIONS FOR DECORATIVE GAS APPLIANCES AND DIRECT VENT HEATERS APPLICATION
5"x 8" DIRECT VENT INSTALLATION INSTRUCTIONS FOR DECORATIVE GAS APPLIANCES AND DIRECT VENT HEATERS APPLICATION These instructions apply to the Simpson Dura-Vent 5"x 8" Direct Vent System. This venting
More informationFLANGED CORR/GUARD CORR/GUARD INSTALLATION INSTRUCTIONS
CORR/GUARD INSTALLATION INSTRUCTIONS This symbol on the nameplate means this product is listed by Underwriters Laboratories Inc. Tested to UL1738 / CAN / ULCS636-08 Listing No. MH26687 Testing No. 11EN
More informationDURAVENT POLYPRO VENTING PRODUCTS
DURVENT POLYPRO VENTING PRODUCTS INDEX FLEX VENTING SYSTEM DPTER KIT... 14-11 -VENT RETROFIT DPTERS... 14-10 CHIMNEY CP... 14-10 CHIMNEY LINING KIT... 14-10 CHIMNEY SUPPORT... 14-11 COUPLER DPTER... 14-12
More informationSMALL DIAMETER CORR/GUARD & SLEEVED CORR/GUARD
CORR/GUARD INSTALLATION INSTRUCTIONS This symbol on the nameplate means this product is listed by Underwriters Laboratories Inc. Tested to UL1738 / CAN / ULCS636-08 Listing No. MH26687 Testing No. 11EN
More informationDuraTech. Installation Instructions. Combustion Air System
Installation Instructions Combustion Air System Combustion Air System (CAS) brings in outside air for wood-burning appliances. Used with the DuraTech chimney system. DuraTech A MAJOR CAUSE OF CHIMNEY RELATED
More informationPelletVent Pro. Installation Instructions. C o m p l e t e V e n t i n g S o l u t i o n s f o r t h e H e a r t h I n d u s t r y
Installation Instructions Venting System For Pellet and Corn Stoves PelletVent Pro C o m p l e t e V e n t i n g S o l u t i o n s f o r t h e H e a r t h I n d u s t r y A MAJOR CAUSE OF VENT RELATED
More informationPellet Stove. Flex Pipe. Appliance Connector
Installation Instructions & Owners Maintenance Guide DT-M Direct-Temp for Multi Fuel L-Vent / Vent System for Pellet, Corn and other Bio-Fuel Burning Appliances Introduction Direct-Temp for Multi-Fuel
More informationCHIMNEYS AND VENTS CHAPTER 8
CHAPTER 8 CHIMNEYS AND VENTS SECTION 801 GENERAL 801.1 Scope. This chapter shall govern the installation, maintenance, repair and approval of factory-built chimneys, chimney liners, vents and connectors.
More informationCorr/Guard PRESSURE RATED VENTING SYSTEM IMPORTANT: DO NOT INSTALL WITHOUT FIRST READING THESE INSTRUCTIONS VERY CAREFULLY.
CORR/GUARD INSTALLATION INSTRUCTIONS This symbol on the nameplate means this product is listed by Underwriters Laboratories Inc. Tested to UL1738 / CAN / ULCS636-1995 Listing No. MH26687 Testing No. 11EN
More informationSL-VENT (oil and gas vent) For use with oil or gas fired appliances. Listed to ULC-609 and UL-641. Available in 5, 6, 7 and 8 I. D.
Typical Installations 0 8 9 Vertical Installation. Vertical Termination ap. Storm ollar. Flashing. Roof Support. Length. ttic Radiation Shield. Firestop 8. ecorative lack Plate 9. Length (lack) 0. Insulation
More informationCHAPTER 8 CHIMNEYS AND VENTS
CHAPTER 8 CHIMNEYS AND VENTS SECTION 801 GENERAL 801.1 Scope. This chapter shall govern the installation, maintenance, repair and approval of factory-built chimneys, chimney liners, vents and connectors.
More informationInstallation Instructions. Venting System for Pellet, Corn, Oil, and Biofuel appliances. PelletVent Pro
Installation Instructions Venting System for Pellet, Corn, Oil, and Biofuel appliances. PelletVent Pro A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE
More informationFasNSeal 80/90 FasNSeal & FasNSeal W2 FasNSeal Flex
FasNSeal 80/90 FasNSeal & FasNSeal W FasNSeal Flex FSNSEL 80/90 hange to High Efficiency? Utilize Your Existing ommon Vent! FasNSeal 80/90 ap LISTINGS Storm ollar Flashing DuraVent s FNS 80/90 ombination
More informationflexible venting simply perfect cost efficient convenient durable Est FREEDOM VENTING FLEX
flexible venting simply perfect cost efficient convenient durable Est. 1990 FLEX FREEDOM VENTING Introduction Freedom Flex Venting systems are top of the line when it comes to materials, cost efficiency
More informationEasy to assemble. Silicone gasket sealed. Laser-welded seams. Smooth joint connections. 360 Lock-Tab secure rotation
Easy to assemble Silicone gasket sealed Laser-welded seams Smooth joint connections 360 Lock-Tab secure rotation Evenly spaced inner and outer pipes Continuous column of air insulation Ultimate Pellet
More informationTYPE L VENT / VENT SYSTEM FOR PELLET BURNING APPLIANCES
INSTALLATION INSTRUCTIONS & MAINTENANCE GUIDE TYPE L VENT / VENT SYSTEM FOR PELLET BURNING APPLIANCES LISTED TO ULC-S609 & UL641 A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES
More informationCHAPTER 8 CHIMNEYS AND VENTS
CHAPTER 8 CHIMNEYS AND VENTS SECTION 801 GENERAL 801.1 Scope. This chapter shall govern the installation, maintenance, repair and approval of factory-built chimneys, chimney liners, vents and connectors.
More informationType B Gas Vent. Installation Instructions
Installation Instructions Round and Oval Type B GasVent Systems for use with natural as or liquid propane category I and draft hood equipped appliances and appliances listed to use Type B Gas Vent. Type
More informationInstallation Instructions. Venting System for Pellet, Corn, Oil, and Biofuel appliances. PelletVent Pro
Installation Instructions Venting System for Pellet, Corn, Oil, and Biofuel appliances. PelletVent Pro A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE
More informationVenting. Vent Material. Approved Venting Accessories Simpson Dura-Vent DV unless otherwise specified. Wall Thickness
Venting Vent Material This unit is approved for installation using 4 x 6-5/8 in co-axial direct vent pipe and accessories manufactured by Simpson Dura-Vent. Follow the installation instructions supplied
More informationPelletVent. Factory-Built Chimney Relining. Installation Instructions. PelletVent Pro (PVP)
Installation Instructions PelletVent Pro (PVP) PelletVent Factory-Built Chimney Relining A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS.
More informationVENT SYSTEM COMPONENTS
Chimney Liner Kits Chimney Liners - All Fuel Chimney Liners - Gas Made from durable, corrosion-resistant type 316 stainless steel Designed to be used with wood, oil, coal and non-condensing gas-fired appliances
More information2012 INTERNATIONAL FUEL GAS CODE VENTS
2012 INTERNATIONAL FUEL GAS CODE SECTION 502 (IFGC) VENTS 502.1 General. All vents, except as provided in Section 503.7, shall be listed and labeled. Type B and BW vents shall be tested in accordance with
More informationWARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual.
Malm Fireplaces, Inc. 368 Yolanda Avenue - Santa Rosa, Ca 95404 (707) 523-7755 - Fax: (707) 571-8036 info@malmfireplaces.com 34 Zircon Direct Vent Tested & Listed by LabTest Certified for use in USA &
More informationFasNSeal 80/90 FasNSeal & FasNSeal W2 FasNSeal Flex
FasNSeal 80/90 FasNSeal & FasNSeal W FasNSeal Flex FSNSEL 80/90 hange to High Efficiency? Utilize Your Existing ommon Vent! FasNSeal 80/90 ap LISTINGS Storm ollar Flashing DuraVent s FNS 80/90 ombination
More informationInstallation Instructions
Installation Instructions Type B Gas Vent Model E/R 3" 8" ECCO TYPE B GAS VENT AND ACCESSORIES ARE FOR USE ONLY WITH LISTED CATEGORY 1 GAS-FIRED APPLIANCES OR APPLIANCES LISTED FOR USE WITH TYPE B GAS
More informationGas Stoves. H15-10 Direct Vent Gas Stove. Model H15-NG10 H15-LP10. Approved Venting Systems
H15-10 Direct Vent Gas Stove Model H15-NG10 H15-LP10 Fuel Type Natural Gas Propane Minimum Supply Pressure 5.0 W.C. (1.25 kpa) 12.0 W.C. (3.00 kpa) Manifold Pressure - High 3.8 W.C. (0.95 kpa) 11 W.C.
More informationVP Pellet Pipe. For pellet burning stoves. FEATURES
CATALOG VP Pellet Pipe For pellet burning stoves. Selkirk gives you the safe, efficient, and cost-effective venting system that's engineered precisely for pellet burning stoves. FEATURES Available in 3"
More informationFasNSeal. Installation Instructions
Installation Instructions FasNSeal & FasNSeal W2 Single-wall and Double-wall special gas vent FasNSeal Flex Flexible chimney liner for special gas vent for Category II, III, and IV appliances FasNSeal
More informationInstallation & Maintenance Instructions
Installation & Maintenance Instructions Listed & Tested to UL641, ULC-S609, ULC/ORD C441 AMERIVENT Model PVP Pellet Pipe Plus Vent Connector for Pellet-Fuel Appliances and Other Low-Temperature Applications
More informationVentis Direct Vent. Installation Instructions
entis Direct ent Installation Instructions A MAJOR CAUSE OF CHIMNEY RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES), TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST IMPRORTANCE THAT
More informationINSTALLATION INSTRUCTIONS
ELIMINATOR 36 Wood Burning Fireplace Models: 36E Non-Circulating (Smooth Face) I36E Non-Circulating (Smooth Face) Fully Insulated INSTALLATION INSTRUCTIONS SAVE THIS BOOK This book is valuable. In addition
More informationSUBJECT: SELKIRK MODEL DT DIRECT VENT SYSTEM FOR PELLET & CORN FIRED APPLIANCES / TERMINATION CLEARANCES TO OPENINGS IN BUILDINGS
Selkirk LLC Selkirk LLC Research & Development State Route 93 North & Sutton Road P.O. Box 631 Logan, OH 43138 9/21/2006 TO: Our Valued Customers FROM: Glen Edgar Director R&D SUBJECT: SELKIRK MODEL DT
More informationMitchell Metal Products, Inc.
Mitchell Metal Products, Inc. Mitchell Metal Products Kosciusko, Mississippi Established 1924 H i g h w a y 1 2 E P. O. B o x 7 8 9 K o s c i u s k o, M S 3 9 0 9 0 O f f i c e : 6 6 2-2 8 9-7 11 0 o r
More informationH35 Direct Vent Gas Stove. 17,500 BTU/h (5.13 kw) 34,000 BTU/h (9.97 kw) 15,000 BTU/h (4.39 kw) 28,500 BTU/h (8.35 kw)
H35 Direct Vent Gas Stove Model H35-NG10 H35-LP10 Fuel Type Natural Gas Propane Minimum Supply Pressure 5.0 W.C. (1.25 kpa) 12.0 W.C. (3.00 kpa) Manifold Pressure - High 3.8 W.C. (0.94 kpa) 11 W.C. (2.74
More informationH35 Direct Vent Gas Stove. 17,500 BTU/h (5.13 kw) 34,000 BTU/h (9.97 kw) 15,000 BTU/h (4.39 kw) 28,500 BTU/h (8.35 kw)
H35 Direct Vent Gas Stove Model H35-NG10 H35-LP10 Fuel Type Natural Gas Propane Minimum Supply Pressure 5.0 W.C. (1.25 kpa) 12.0 W.C. (3.00 kpa) Manifold Pressure - High 3.8 W.C. (0.94 kpa) 11 W.C. (2.74
More informationDirect Vent System. for PELLET STOVES FEATURES. Includes all Selkirk Model VP Pellet Pipe and Direct-Temp components needed to complete a system
CTLOG Direct Vent System for PELLET STOVES Includes all Selkirk Model VP Pellet Pipe and Direct-Temp components needed to complete a system Direct-Temp for pellet stoves is the revolutionary, high-performance
More informationShasta Vent Inc All-Fuel HT Chimney Installation Instructions
Shasta Vent Inc All-Fuel HT Chimney Installation Instructions August 2015 v1.02 A MAJOR CAUSE OF CHIMNEY RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS.
More informationInstallation Instructions for PTS Chimney Liners: Ventinox /DuraFlex Pro /DuraFlex SW
Hearth Liners Installation Instructions No. 2051 2009 (Rev. 3/2009) Installation Instructions for PTS Chimney Liners: Ventinox /DuraFlex Pro /DuraFlex SW READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING
More informationSUBMITTAL RECORD. ULC S636 - PolyPro. Single-Wall Double-Wall Concentric Flex
SUMITTL RECORD ULC S636 - PolyPro Polypropylene vent pipe for use with NSI Category II and IV gas-burning appliances, including high efficiency water heaters, condensing boilers and warm air furnaces.
More informationANY EVERY ONE ONE No matter what the venting application, from gas fired to oil to all fuel heating equipment, Z-FLEX is your one-stop solution.
NY EVERY ONE ONE No matter what the venting application, from gas fired to oil to all fuel heating equipment, Z-FLEX is your one-stop solution. Specialists in Flexible Z-FLEX has been providing flexible
More informationMODEL CF CEILING SUPPORTED CHIMNEY
Manufactured by Selkirk Canada Corp. - Hamilton, Ontario Installation Instructions for MODEL CF CEILING SUPPORTED CHIMNEY Round Top Storm Collar Flashing Attic Insulation Shield/Firestop Spacer Intermediate
More informationGas Stoves. C34-10 Direct Vent Gas Stove. Side wall E F. Back wall F E. Model C34-NG10 C34-LP10
Back wall Gas Stoves Model C34-NG10 C34-LP10 Fuel Type Natural Gas Propane Minimum Supply Pressure 5.0 W.C. (1.25 kpa) 12.0 W.C. (3.00 kpa) Manifold Pressure - High 3.8 W.C. (0.95 kpa) 11 W.C. (2.74 kpa)
More informationZ-VENT MODEL SVE SERIES III INSTALLATION AND MAINTENANCE INSTRUCTIONS
Z-VENT MODEL SVE SERIES III INSTALLATION AND MAINTENANCE INSTRUCTIONS 3 & 4 SPECIAL STAINLESS STEEL VENTING SYSTEM FOR GAS BURNING APPLIANCES CATEGORY I, II, III, & IV TESTED AND LISTED BY UNDERWRITERS
More informationEXCEL. ULTRABlack THE MOST DURABLE, EASIEST TO INSTALL RESIDENTIAL CHIMNEY SYSTEM YOU CAN BUY NEVER EVER BUY ANOTHER STOVE PIPE
THE MOST DURABLE, EASIEST TO INSTALL RESIDENTIAL CHIMNEY SYSTEM YOU CAN BUY ULTRABlack NEVER EVER BUY ANOTHER STOVE PIPE Chimney To determine what parts you need for your woodstove installation, try the
More informationNovaVent. Dimensional Data
NovaVent Dimensional Data NovaVent The new vent system designed and engineered for today s competitive sales environment. NovaVent NovaVent is designed and engineered to meet the requirements of gas-fired
More informationInstallation Instructions. PolyPro Single-Wall Gas Vent System for Category II & IV Gas-Burning Appliances. PolyPro
Installation Instructions PolyPro Single-Wall Gas Vent System for Category II & IV Gas-Burning Appliances PolyPro A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES)
More informationP P Gas Fireplace. P See Thru
P121-10 - P131-10 Gas Fireplace Model P121/P131-NG10 P121/P131-LP10 Fuel Type Natural Gas Propane Minimum Supply Pressure 5 W.C. (1.25 kpa) 12 W.C. (3.00 kpa) Manifold Pressure - High 3.8 W.C. (0.95 kpa)
More informationPolyPro: For Venting Condensing Appliances Environmentally Safe Alternative Lower Over-All Cost Than PVC Engineered Terminations Fast, Easy To Install
PolyPro : For Venting Condensing Appliances Environmentally Safe Alternative Lower Over-All Cost Than PVC Engineered Terminations Fast, Easy To Install Being Green, Being Responsible. DuraVent looks for
More informationGWS. Venting Manual. Gas-Fired Water Boilers. Hazard definitions. Contents. Venting method definitions
GWS Gas-Fired Water Boilers Venting Manual Hazard definitions Contents Page Hazards that will cause severe personal injury, death or substantial property damage. Hazards that can cause severe personal
More informationThe Monterey (PENNINSULA) MODEL PN36 3-SIDED, WOOD-BURNING FIREPLACE
The Monterey (PENNINSULA) MODEL PN36 3-SIDED, WOOD-BURNING FIREPLACE INSTALLATION AND OPERATING INSTRUCTIONS SAVE THIS BOOK This book is valuable. In addition to instructing you on how to install and maintain
More informationInstallation Instructions. PolyPro Single-Wall Gas Vent System for Category II & IV Gas-Burning Appliances. PolyPro
Installation Instructions PolyPro Single-Wall Gas Vent System for Category II & IV Gas-Burning Appliances PolyPro A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES)
More informationINSTALLATION INSTRUCTIONS
DISTRIBUTED BY: SBI VENTING DIVISION 2100 insulated chimney All-Fuel Chimney System INSTALLATION INSTRUCTIONS A MAJOR CAUSE OF CHIMNEY-RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIRSPACES)
More informationVERTICAL POWER VENT KIT
INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference. These instructions are supplementary to the Installation and Operating Instructions supplied with the
More informationInstallation Instructions. PolyPro Single-Wall Gas Vent System for Category II & IV Gas-Burning Appliances. PolyPro
Installation Instructions PolyPro Single-Wall Gas Vent System for Category II & IV Gas-Burning Appliances PolyPro A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES)
More informationUltimate Pellet Pipe
INSTALLATION INSTRUCTIONS & MAINTENANCE GUIDE A MAJOR CAUSE OF VENT RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF THE UTMOST IMPORTANCE THAT THIS
More informationInstallation and Maintenance Instructions
Commercial & Industrial Positive Pressure or Condensing AL 29-4C Stainless Steel High Challenge Special Gas Vent Also for Natural Draft Appliances 3",4",5",6",7",8",9",10" and 12" Diameter Special Gas
More informationVenting Supplement. Direct Vent Through-Roof or Through-Unused-Chimney. Water Boiler Series 3 & 4
GOLD GV Water Boiler Series 3 & 4 Venting Supplement Direct Vent Through-Roof or Through-Unused-Chimney For use with Weil-McLain Through-Roof or Through- Unused-Chimney Termination Kit Kit part # 382-200-435
More informationTwin wall Air Gap Insulated Zalutite & Aluminium Commercial Gas Vent Chimney System
Q Twin wall ir Gap Insulated Zalutite & luminium ommercial Gas Vent himney System Designed for Individual and Modular Natural Draught Gravity Flow himney pplications PRODUT INFORMTION INTRODUTION Q is
More informationC. Manufactured double wall chimneys for fuel fired equipment. D. NFPA 54 - National Fuel Gas Code; National Fire Protection Association; 2009.
SECTION 235100 - BREECHINGS, CHIMNEYS, AND STACKS PART 1 GENERAL 1.1 SECTION INCLUDES A. Fabricated breechings. B. Manufactured chimneys for gas fired equipment. C. Manufactured double wall chimneys for
More informationVertical Termination Part No: 3CGRVT 16 7/8" 18 Vent Pipe Extension Part No: 3CG18 9 7/8" Wall Hanger Part No: 3CGWH 7 7/8" 7 3/8"
Corr/Guard Direct Vent Water Heater Vent/Air Intake System Installation and service must be performed by a qualified installer, service agency or the gas supplier. Installation must meet all state and
More information200i. Vent/air manual. Installation instructions for vent and air piping. Also read and follow: 200i Boiler manual 200i Control manual
M2i-VAM-2 Cast iron condensing boiler 200i Vent/air manual Installation instructions for vent and air piping Also read and follow: 200i Boiler manual 200i Control manual This manual is intended only for
More informationINSTALLATION INSTRUCTIONS
42" WOODBURNING FIREBOX Model C42EC2 Circulating (Louvered) INSTALLATION INSTRUCTIONS SAVE THIS BOOK This book is valuable. In addition to instructing you on how to install and maintain your appliance,
More informationSt. Croix Greenfield Installation Manual
St. Croix Greenfield Installation Manual Table of Contents General Information... 1 Installation Check List... 2 Approved Installations... 3 Exhaust Venting... 4 Venting - Approved Materials... 4 Venting-Typical
More informationGAS FIRED BOILERS FOR FORCED HOT WATER VENTING ADDENDUM. ECR International Ltd. - Olsen Division P.O. Box 900 Wallaceburg, Ont.
ODV-B GAS FIRED BOILERS FOR FORCED HOT WATER VENTING ADDENDUM ECR International Ltd. - Olsen Division P.O. Box 900 Wallaceburg, Ont. N8A5E5 TABLE OF CONTENTS HORIZONTAL PIPING... PAGES 1-10 WARNINGS...
More informationSaf-T Vent SC Plus/SC 316
Installation and Maintenance Instructions Saf-T Vent SC Plus/SC 316 Double Wall One Inch Air Space Special Gas Vent For Venting Residential and Light Commercial Appliances Category I,II,III,IV Appliances
More informationZC Kit AGP Pellet Insert
ZC Kit AGP Pellet Insert Compatibility AGP Pellet Insert Lopi AGP Pellet Insert Overview Packing List ZC Can Rear Panel ZC Can Top/Side Panel Bottom Panel (Fiber Board with Steel) (40) # 8 x 3/8 Type A
More informationTwin Wall Installation Instructions And Maintenance Guide
Twin Wall Installation Instructions And Maintenance Guide Please read all instructions before beginning your installation. Failure to install this system in accordance with these instructions will invalidate
More informationThe intelligent alternative for flue gas venting systems
The intelligent alternative for flue gas venting systems FIRST LISTED InnoFlue is the first polymeric vent system tested and listed to ULC-S636 and UL-1738 in North America Intelligent for a good reason
More informationSWB400I DELUXE RADIANT WOOD BURNING FIREPLACE INSTALLATION, OPERATION AND MAINTENANCE MANUAL
SWB4I DELUXE RADIANT WOOD BURNING FIREPLACE INSTALLATION, OPERATION AND MAINTENANCE MANUAL The SWB4I fireplace is an insulated radiant wood burning fireplace with a 6-inch wide front opening. It comes
More informationInspection Checklist Mechanical Final
Property Owner Name: Property Address: Property Parcel Number: Inspectors Name: Review Date: Permits and Plans 1. Job address is posted in a visible location. (R319.1) 2. Permit and approved plans, and
More informationAdvanced Venting Systems
Advanced Venting Systems 1 Z-Vent Special Gas Vent 3 Flexible Vent Connector Systems 5 Aluminium Chimney Liner System 7 Stainless Steel Chimney Liner System 9 Oval Liner System / Advancing the Industry
More informationThat s The Metal-Fab Way Experience The Difference
1 Faster. Safer. etter. Metal-Fab provides complete and comprehensive venting solutions to the HV, hearth and plumbing markets. Founded in 1959, on the premise that better products and services would be
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FACTORY BUILT CHIMNEY CONNECTOR A MAJOR CAUSE OF CHIMNEY CONNECTOR RELATED FIRES IS FAILURE TO MAINTAIN REQUIRED CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF THE
More informationINSTALLATION INSTRUCTIONS FOR SV4.5RR4 PIPE REDUCER AND ALL ASSOCIATED SV4
1508 Elm Hill Pike, Suite 108 Nashville, TN 37210 P Rev. C 06/2014 INSTALLATION INSTRUCTIONS FOR PIPE REDUCER AND ALL ASSOCIATED SV4 (4") SECURE VENT/DIRECT VENT COMPONENTS INCLUDING SV4CGV-1 VERTICAL
More informationORTAL Power Vent System Manual Table of Contents
Ortal Power Vent System: Installation Manual ORTAL Power Vent System Manual Table of Contents 1. Introduction 2 2. Safety Warnings 2 3. The ORTAL Power Vent System 3 a. Power Vent 4 b. Pathways and Fan
More informationINSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT
Read and Save These Instructions All Hoods Must Be Installed By A Qualified Installer INSTALLATION INSTRUCTIONS WALL MOUNT LINER INSERT Read All Instructions Thoroughly Before Beginning Installation WARNING
More informationANY EVERY ONE ONE No matter what the venting application, from gas fired to oil to all fuel heating equipment, Z-FLEX is your one-stop solution.
ANY EVERY ONE ONE No matter what the venting application, from gas fired to oil to all fuel heating equipment, Z-FLEX is your one-stop solution. Specialists in Flexible Z-FLEX has been providing flexible
More informationDirect Exhaust Venting Kit Instructions
CONDENSING GAS BOILER 220/299/300/399 Direct Exhaust Venting Kit Instructions Evergreen 220/299/300/399 Kit part number 383-500-769 STOP! Read before proceeding Hazard definitions The following defined
More informationSEPARATED COMBUSTION WARNING
CUSTOMER AGENCY PROCESS CQS CONVERGENT QUALITY SYSTEM PRODUCT WARRANTY START-UP Form I-SDH-V (Version.5) Obsoletes I-SDH-V (Version.4) Vent Installation Applies to: Venting Requirements for PREEVA Separated-Combustion
More informationAL29-4C (UNS S44735) Direct Vent System for Category II, III & IV Heating Equipment 3 through 16
L29- (UNS S7) Direct Vent System for ategory II, III & IV Heating Equipment through Set the standard as the first vent system with a built-in gasket and locking band, designed for high efficiency gas heaters
More informationInspection Checklist Mechanical Rough in
Property Owner Name: Property Address: Permit Number: Inspectors Name: Review Date: Permits and Plans 1. Job address is posted in a visible location. (R319.1) 2. Permit and approved plans are on site and
More informationINSTALLATION AND OPERATING INSTRUCTIONS
PENINSULA MODEL VPN36 3-SIDED, WOODBURNING FIREBOX INSTALLATION AND OPERATING INSTRUCTIONS SAVE THIS BOOK This book is valuable. In addition to instructing you on how to install and maintain your appliance,
More informationTW-Pro. Twin Wall Insulated Flue System EN T600 N1 W V2 L50040 G50 / O40
TW-Pro Twin Wall Insulated Flue System EN1856-1 T600 N1 W V2 L50040 G50 / O40 Approvals TW-Pro Twin Wall Insulated Flue System - TW-Pro has been specifically designed with the installer in mind with a
More information