SECTION DESIGN REQUIREMENTS DIVISION 23 (HVAC) PREFERRED MANUFACTURERS GENERAL INFORMATION
|
|
|
- August Dawson
- 6 years ago
- Views:
Transcription
1 DIVISION 23 (HVAC) PREFERRED MANUFACTURERS GENERAL INFORMATION 1.1 Manufacturers on this list fall into two categories: a. Preferred Manufacturers: indicated in highlighted text, these products are pre-approved. b. Conditional Approval: Manufacturers approved for certain projects. Contact Columbia University Facilities (CUF) for approval to use on new projects. 1.2 This list is intended to cover major equipment vendors listed in the Specification sections. Often, ancillary vendors used to construct the equipment are listed within the specification sections (e.g. pipe and duct sealants, firestopping, etc.). This list does not absolve the Consultant from reading and complying with the requirements set forth in the Specification Sections and sound engineering practices. 1.3 Corrections/Substitutions: If there are errors in model numbers or manufacturers listed, or if a model is no longer available, notify Columbia University Facilities in writing for a clarification. A response regarding the Correction or Substitution will be provided EXPANSION JOINTS AND LOOPS 1. Expansion Joints - Bellow Type (Packless) a. Badger Company Series 300 b. Adsco Company 2. Expansion Joints - Slip Joint (Packed) For Steam Piping a. Advanced Thermal Systems b. Adsco Company c. Hyspan 2. Anchor and Guides a. Grinnell b. Metraflex HANGERS AND SUPPORTS FOR PIPING AND EQUIPMENT 1. Pipe Hangers, Inserts, Saddles, Beam Clamps a. B-line Systems, Inc. b. Carpenter & Patterson, Inc. c. Grinnell Corp. 2. Channel Support Systems a. B-Line Systems, Inc. b. Grinnell Corp.; Power-Strut Unit c. Thomas & Betts Corp. d. Unistrut Corp. 3. Thermal-Hanger Shield Inserts a. Carpenter & Patterson, Inc. b. Pipe Shields, Inc. c. Value Engineered Products, Inc. 4. Expansion Shield a. Grinnell b. Hilti, Inc. c. Pipe Shields Inc. 5. Pre-Insulated Pipe Supports - Pipe Shields, Inc. 6. Pre-Insulated Riser Clamps - Pipe Shields, Inc. 1
2 7.Sleeves - Link Seal - Century Line Sleeve, Thunderline Corp MECHANICAL INSULATION 1. Pipe Insulation Type A - Calcium Silicate - Manville, Thermo Pipe Insulation Types B and C - Glass Fiber a. Owens-Corning, Evolution Pipe Insulation with ASJ b. Knauf - Pipe Insulation With ASJ c. Certainteed - Type 500 Snap-on with ASJ d. Manville - Micro-Lok 650 With A-T Plus Jacket 3. Pipe Insulation Type D - Foam a. Armstrong - Type AP ARMAFLEX b. Nomaco, Inc. - Type THERMA-CEL 4. Pipe Inserts a. Grinnell b. B-Line 5. PVC Covering (Elbows and Fittings) a. Zeston b. Proto c. Ceel-co 6. Pipe Shields - Grinnell Figure Duct Insulation - Flexible Glass Fiber a. Owens-Corning Fiberglass - Foil-faced duct wrap. b. Knauf - Type ECOSE with foil face c. Certainteed Softouch with foil face 8. Duct Insulation - Rigid Glass Fiber a. Owens-Corning - Type ASJ-705 b. Knauf Duct board with ECOSE c. Certainteed - Certapro 9. High Temperature Applications - Calcium Silicate a. Manville b. Industrial Insulation Group 10. Tank Enclosures and Accessories - Semi- Rigid Glass Fiber a. Owens-Corning - Type 703 b. Certainteed Crimp wrap c. Knauf Kwik Flex d. Manville - Microflex 11. Pump Enclosures - Rigid Glass Fiber a. Owens-Corning - Type 705 b. Manville - Type 800 c. Certainteed - Certapro BUILDING AUTOMATION SYSTEMS (BAS) 1. Building Automation Systems - Note: BAS selected MUST match existing Building BAS if used in renovation work. a. Andover b. Siemens Building Technologies HYDRONIC PIPING SPECIALTIES AND PIPING GUIDELINES 1. Manual Air Vents a. Bell and Gossett - No. 4V b. Taco, Inc c. Armstrong Pumps, Inc. - #72 2. Automatic Air Vents a. Bell and Gossett - #107 High Capacity Air Vent b. Taco, Inc. - Hy-vent c. Spirax/Sarco - 13WS 3. Diaphragm-type Expansion Tanks a. Bell and Gossett Series B or Series D b. Taco, Inc. - CA Series c. Armstrong Pumps, Inc. - Series AX 4. Air Separators a. Bell and Gossett - Rolairtrol b. Taco, Inc. - Air Separator 5. Relief Valves a. Bell and Gossett b. Amtrol c. Armstrong d. McDonnell and Miller 2
3 6. Suction Diffusers a. Bell & Gossett b. Armstrong 7. Backflow Preventers - Double Check Type a. Watts No. 709 b. Hersey 8. Backflow Preventers - Reduced Pressure Type a. Watts 909 b. Hersey METERS AND GAUGES 1. Thermometers a. Marsh b. Trerice - B Series c. Weiss d. Weksler 2. Pressure Gauges a. Ashcroft - Duraguage Series b. Marsh c. Weiss - PG Series d. Weksler - AAT Series e. WIKA f. U.S. Gauge g. Trerice - 500X Series HYDRONIC PUMPS 1. In-Line Circulators: a. Armstrong Pumps, Inc. b. Bell & Gossett ITT (Series 60 and 80) c. Grundfos Pumps Corp. 2. Compact In-Line Circulators a. Armstrong Pumps, Inc. b. Bell & Gossett ITT c. Grundfos Pumps Corp. d. PACO Pumps e. Taco 3. Vertical In-line Pumps: a. Armstrong Pumps, Inc. b. Bell & Gossett lit c. Goulds Pumps, Inc. d. Grundfos Pumps Corp. e. PACO Pumps f. Peerless Pump Co. 9. Dielectric Fittings - Union Type - EPCO with Epconite No Dielectric Fittings - Nipple Type a. ClearFlow b. EPCO 11. Y Type Strainers a. Sarco b. Armstrong c. Mueller 3. Air Flow Gauges (Magnehelic) - Dwyer 4. Test Plugs (Requires University Approval) a. Peterson - Petes Plug b. Weksler c. Trerice 5. Steam Meter - Emco 6. Chilled Water Meter - Siemens (Controlotron) g. Taco 4. Flexible-Coupled, End-Suction Pumps: a. Goulds Pumps, Inc. b. Ingersoll-Dresser Pump Co. c. PACO Pumps. d. Taco e. Weil Pump Company, Inc. 5. Flexible-Coupled, Double Suction Pumps: a. Bell & Gossett ITT b. Goulds Pumps, Inc. c. Ingersoll-Dresser Pump Co. d. PACO Pumps. e. Peerless Pump Go. f. Taco g. Fairbanks Morse Pump Corp. 6. Steam Condensate Pump Units: a. Federal Pump 3
4 b. Bell & Gossett ITT c. Roth Pump Company d. Sarco Pumps 7. Condensate Drainage Pump Units: STEAM AND CONDENSATE PIPING SPECIALTIES 1. Steam Traps - Thermostatic - Spirax/Sarco TA-125, TH Steam Traps - Float and Thermostatic - Spirax/Sarco FT Steam Traps - Inverted Bucket Trap - Spirax/Sarco B Series 4. Air Vents a. Spirax/Sarco VS206 (steam) b. Spirax/Sarco 13WS (condensate) 5. Vacuum Breakers - Spirax/Sarco VB14 6. Pressure Regulating Valves a. Leslie b. Spence Engineering Co. Type ED HVAC Ducts and Casings 1. Flexible Ductwork a. Clevaflex b. Thermaflex c. Flexmaster 2. Volume Dampers - Single Blade (Rectangular) a. Air Balance AC-111 b. Greenheck c. Ruskin MD25 3. Volume Dampers - Single Blade (Round) a. Air Balance AC-112 b. Greenheck MBDR50 c. Ruskin MORS25 4. Volume Dampers - Multiple Blade - Note: Opposed Blade Type ONLY a. Air Balance AC-2 b. Greenheck MBD-15 c. Ruskin 5. Fire Damper - Fusible Link a. Air Balance Inc. Series D19 b. Imperial c. Prefco Products Series 5500 d. Ruskin 6. Smoke Damper - Airflow Blade a. Hartell Div.; Milton Roy Co. b. Little Giant Pump Co. c. Marsh Manufacturing, Inc. 7. Safety Shutoff Valves a. Spence b. Leslie 8. Safety Relief Valves a. O.C. Keckley Bronze Series 40 b. Spence Engineering Bronze Series 41 c. Spirax/Sarco 9. ` Y Type Strainers a. Sarco Type b. Armstrong c. Mueller a. Air Balance Inc. SA 1 b. Greenheck SD33 c. Ruskin SD60 d. Imperial 7. Combination Fire/Smoke Damper a. Ruskin FSD60 8. Duct Sealant a. 3M Fastbond 900 b. Foster c. MEI44-52 d. Hardcast Sure Grip 404, Hardcast Iron Grip Louvers a. Ruskin b. Arrow c. Air Balance 10. Access Doors in Walls and Ceilings a. Cesco b. J L Industries c. Karp d. Milcor 11. Filters a. AAF International b. Farr Company 4
5 c. Flanders Filters, Inc. d. Koch Filter Corporation HVAC Fans 1. Cabinet and Ceiling Fans a. Cook Gemini Series b. Greenheck Model SP, CSP and BCF c. Penn Zephyr Series 2. Square In-Line Centrifugal a. Cook SQI or SQN Series b. Greenheck Model SQ or BSQ c. Penn Centrex Inliner SX 3. Tubular Centrifugal a. Greenheck TCS Series b. Loren Cook 4. Centrifugal Utility Fans a. Greenheck b. Belted Utility Vent Sets c. Loren Cook 5. Belted Utility Vent Sets - Laboratory Exhaust a. Loren Cook b. Buffalo Air 6. Roof/Wall Exhaust a. Cook AC Series b. Greenheck Models G, GB and C Series c. Penn Domex, Fumex 7. Axial Propeller Wall Fan a. Cook S Series Wall Ventilators b. Greenheck SB and S Series c. Penn Breezeway Series 8. Vaneaxial a. Greenheck VAB Series b. Cook Series VA Series Air Terminal Units 1. Air Terminal Units a. Anemostat b. Titus c. Environmental Technologies d. Krueger Air Outlets and Inlets 1. Directional Ceiling Supply Air Diffuser - Type "A" a. Titus TDC, with AG-65S damper and b. Krueger Series SH, with 5-11 damper and c. Anemostat SD, with DOB or DED damper and 2. Fixed Ceiling Supply Air Diffuser - Type "B" a. Titus TMS, with AG-65 damper and b. Krueger Series 1400, with R-11 damper and c. Anemostat E, with Columbia University-1 damper and 3. Perforated Ceiling Supply Air Diffuser - Type "C" a. Titus PAS, with AG-65 damper and b. Krueger Series 1100, with R 11 damper and c. Anemostat PR 4. Fixed Ceiling Supply Air Diffuser - Type "D" a. Titus TMS, with AG-65 damper and b. Krueger Series 1400, with R-11 damper and c. Anemostat E, with Columbia University-1 damper and 5
6 5. Ceiling Supply Air Linear Diffuser - Type "E" a. Titus ML-37, ML-38, or ML-39 b. Krueger Series c. Anemostat AL 6. Sidewall, Sill, Or Floor Supply Linear Air Diffuser - Type "F" a. Titus CT -480 or CT -481 b. Krueger Series c. Anemostat Al 7. Fixed Supply Air Register - Type "G" a. Titus 300RS with AG-15 damper b. Krueger 880V with OBD damper c. Anemostat S2VO 8. Perforated Ceiling Return Air Diffuser - Type "H" a. Titus PAR b. Krueger Series 1190 c. Anemostat 3P 9. Ceiling Return Linear Air Diffuser - Type "I" a. Titus ML-37, ML-38, or ML-39 b. Krueger Series 1900 c. Anemostat SLAD 10. Return, Exhaust, Or Transfer Fixed Air Register Type J a. Titus 300RS with AG-15 damper b. Krueger S80H with OBD damper c. Anemostat S30D 11. Perforated Return, Exhaust, Or Transfer Air Register - Type K a. Titus 8F with AG-35 damper b. Krueger S80P with OPO damper 12. Laboratory Perforated - Ceiling Supply and Diffuser - Type OIL" a. Titus Tritec 13. Return, Exhaust, Or Transfer Fixed Air Grille - Type M a. Titus 350RL b. Krueger S80H c. Anemostat S3HD 14. Return, Exhaust, Or Transfer Perforated Air Grille - Type "N" a. Titus 8F b. Krueger S80P 15. Return, Exhaust, Or Transfer Eggcrate Air Grille - Type "0" a. Titus 50P b. Krueger EGC-5 c. Anemostat GC5 16. Filter Return Grille - Type "P" a. Titus 4FF b. Krueger S80P5FF-1 c. Anemostat 35HQ 17. Ducted HEPA Filter Supply Terminal- Type "Q" a. Flanders Filter Company Model Heat Exchangers for HVAC 1. U- Tube Heat Exchangers (Steam to Water) a. Bell & Gossett ITT - Type 'SU' b. Taco, Inc. - 'Steam to Liquid Heat Exchanger.' 2. U-Tube Heat Exchangers (Water to Water) a. Bell & Gossett ITT - Type 'WU' b. Taco, Inc. - 'Liquid to Liquid Heat Exchanger.' 3. Plate and Frame Heat Exchangers a. Alfa Laval b. Tranter c. American Vicarb 4. Steam-to-Steam Heat Exchangers (Clean Steam Generators) a. Cemline b. Patterson-Kelly 6
7 Air Handling Units 1. Modular AHUs a. Trane Modular Series b. Carrier c. York 2. Custom AHUs a. Buffalo Air b. Climate Craft 7
PREFERRED MANUFACTURERS - MECHANICAL
PREFERRED MANUFACTURERS - MECHANICAL GENERAL INFORMATION 1.1 Manufacturers on this list fall into two categories: a. Preferred Manufacturers: indicated in highlighted text, these products are pre-approved.
PREFERRED MANUFACTURERS
PREFERRED MANUFACTURERS GENERAL INFORMATION 1.1 Manufacturers on this list fall into four categories: a. Preferred Manufacturer: Approved manufacturers for use on Columbia University projects. b. Conditional
OKLAHOMA STATE UNIVERSITY - BUILDING DESIGN STANDARDS
Page 1 PART 1 GENERAL 1.1 SUMMARY A. Work of this section includes providing basic mechanical materials including, but not limited to, the following: 1. Valves. 2. Pipe expansion joints. 3. Supports and
mechreps.com SAN ANTONIO COLLEGE STATION AUSTIN CORPUS CHRISTI RIO GRANDE VALLEY
SAN ANTONIO AUSTIN 210.650.9005 512.444.1835 CORPUS CHRISTI 800.650.6507 COLLEGE STATION 800.650.6507 RIO GRANDE VALLEY 956.412.1110 AIR MOVEMENT ACCUREX accurex.com Kitchen Hood Systems, Make-Up Air Equipment,
COHASSET, MA March 6, The following is the HVAC outline specifications, which defines the scope of work of the HVAC system.
23 00 00 HEATING, VENTILATING & AIR-CONDITIONING The following is the HVAC outline specifications, which defines the scope of work of the HVAC system. PART 1 GENERAL 1.1 CODES A. All work installed under
SECTION HYDRONIC PIPING AND SPECIALTIES
SECTION 15511 HYDRONIC PIPING AND SPECIALTIES PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Pipe Materials. 2. Fittings. 3. Specialty Items. 4. Glycol Antifreeze Protection. 5. Process Cooling B.
DOCUMENT TABLE OF CONTENTS
DOCUMENT 00003 June 16, 2005 TABLE OF CONTENTS DOCUMENT NO. INTRODUCTORY INFORMATION DOCUMENT 00003 TABLE OF CONTENTS DIVISION 1 GENERAL REQUIREMENTS SECTION 01011 SECTION 01025 SSP21.1-1 SECTION 01026
A. Operation and Maintenance Data: For pumps to include in emergency, operation, and maintenance manuals.
SECTION 23 21 23 - HYDRONIC PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
EXHAUST FAN SCHEDULE
DUCTWORK SCHEDULE CONCEALED SUPPLY AIR RECTANGULAR, RTU CONCEALED SUPPLY AIR RECTANGULAR, ERV CONCEALED SUPPLY AIR ROUND, RTU CONCEALED SUPPLY AIR ROUND, ERV EXPOSED SUPPLY AIR ROUND RUNOUTS RETURN AIR
MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 22 PLUMBING
SECTION 221123 - DOMESTIC WATER PUMPS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following all-bronze and bronze-fitted centrifugal pumps for domestic cold- and hot-water circulation: 1.
DENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION PUMPS
PART 0 A/E INSTRUCTIONS 0.01 Design Requirements A. Pumping system design 1. A primary-secondary pumping system is preferred. Redundant pipes are required for chillers and boilers. 2. Select pumps to operate
HYDRONIC SPECIALTIES TACO AC(F)-CA 05/08/2008
SECTION 15181 - HYDRONIC SPECIALTIES PART 1 - GENERAL 1.1 SECTION INCLUDES A. Air separators B. Expansion tanks C. Pump accessories 1.2 RELATED SECTIONS A. Section - Plumbing Piping Specialties B. Section
STEAM AND CONDENSATE PIPING AND PUMPS DESIGN AND CONSTRUCTION STANDARD
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
Appendix B. Symbols for Drawings. Table B.1. Air moving devices and ductwork symbols. Air Movement. Fans. Axial flow fan.
Appendix B Symbols for Drawings Table B.1 Air moving devices and ductwork symbols Air Movement Fans Axial flow fan Centrifugal fan Propeller fan Intake roof ventilator (supply) Exhaust roof ventilator
UNIVERSITY OF MISSOURI Building Hydronic Piping and Pump Systems 2017 Q3
GENERAL: Hydronic systems included in this document are chilled water, heating hot water, dual temperature and glycol based systems. DESIGN GUIDELINES: Design General 1. Where campus steam is available,
INDUSTRIAL PRODUCTS VOLUME 4
Since 1966 Serving Southwestern Ontario. INDUSTRIAL PRODUCTS VOLUME 4 SOUTHWESTERN ONTARIO Silencer Manufacturing: Woodbridge, Ontario TORONTO-MADE SILENCERS SMWIA-L30 YELLOW LABEL MANUFACTURING PRICE
SECTION STEAM AND STEAM CONDENSATE SPECIALTIES
SECTION 23 22 18 STEAM AND STEAM CONDENSATE SPECIALTIES PART 1 - GENERAL 1.1 SECTION INCLUDES A. Steam Traps. B. Flash Tanks. C. Condensate Return Units. D. Pressure Reducing Valves. E. Safety Valves.
HYDRONIC SPECIALTIES TACO AC(F)-PAX 05/15/2008
SECTION 15181 - HYDRONIC SPECIALTIES PART 1 - GENERAL 1.1 SECTION INCLUDES A. Air separators B. Expansion tanks C. Pump accessories 1.2 RELATED SECTIONS A. Section - Plumbing Piping Specialties B. Section
TABLE OF CONTENTS DIVISION 23 HVAC PIPING AND EQUIPMENT
TABLE OF CONTENTS DIVISION 23 23 00 00...1 23 00 01 GENERAL...1 23 00 02 REFERENCES, REGULATORY REQUIREMENTS...1 23 00 03 REFERENCES, RELATED SECTIONS of the SPECIFICATIONS...1 23 00 04 DEFINITIONS...1
B. Shop Drawings: Detail fabrication of pipe anchors, hangers, special pipe support assemblies, alignment guides, expansion joints and loops,
SECTION 23 21 13 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
Manufacturers Representatives Since Industrial Systems, Inc. Computer Support, Inc
Manufacturers Representatives Since 1974 Industrial Systems, Inc. Computer Support, Inc. www.industrialsystems.org 1-800-460-0469 210-493-4200 ENGINEERED PRODUCTS FOR THE ENGINEERED ENVIRONMENT Sewage
DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) STEAM AND CONDENSATE PIPING AND PUMPS
23 22 00 PART 1 - GENERAL 1.01 SYSTEM DESCRIPTION A. Steam Distribution System: Steam is the primary heat source for a variety of heating functions throughout the Pullman campus of Washington State University.
PROJ. NO SECTION HYDRONIC PIPING
SECTION 23 21 13 HYDRONIC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
A. This Section includes the following domestic water piping specialties:
SECTION 221119 DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
PROJ. NO SECTION METERS AND GAGES FOR HVAC PIPING
SECTION 23 05 19 METERS AND GAGES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
4. Provide brass valve tags marked for the service. See pertinent service specification for valve type.
Section includes various guidelines for valves, instrumentation for process systems, meters, thermometers, and gauges. This design guideline is written to the designer of record (DOR). This guideline is
YALE Site Specifications AIR VENT SCHEDULE
SECTION 23 21 16 01 PIPING SPECIALTIES APPENDIX Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 AIR VENT SCHEDULE Tag AV-1 AV-2 AV-3 Type Automatic Float Low Pressure
Copyright 2003 and 2005 by The American Institute of Architects (AIA) Modified by MSU Physical Plant / Engineering and Architectural Services
Page 238216-1 Copyright 2003 and 2005 by The American Institute of Architects (AIA) Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA Modified by MSU Physical
AIR DISTRIBUTION DIVISION VOLUME 4
AIR DISTRIBUTION DIVISION VOLUME 4 PROVINCE OF QUEBEC PREMIUM GRILLES & DIFFUSERS Linear Diffusers & Grilles VAV Diffusers Underfloor Air Distribution Ceiling Component Diffusers Ceiling Diffusers Grilles
. ECTION METERS AND GAGES
. ECTION 230519 - METERS AND GAGES PART I - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Divisions 00 thru 01 Specification
SECTION LABORATORY and DE-IONIZED WATER SYSTEMS STANDARD CONSTRUCTION STANDARD
PART 1: GENERAL 1.01 Codes and Standards: A. Plumbing Code Compliance: Comply with applicable portions of National Standard Plumbing Code pertaining to selection and installation of Plumbing materials
University of Houston Master Construction Specifications Insert Project Name SECTION FIRE PROTECTION PUMPS PART 1 - GENERAL
SECTION 21 30 00 FIRE PROTECTION PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section 23 01 00,
SECTION PUMPS. 6. Section Steam and Condensate Piping and Specialties.
SECTION 15540 PUMPS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Base Mounted Pumps. 2. Horizontal Split Case Pumps. 3. In line Pumps. 4. Steam Condensate Return Pumps. B. Related Sections: 1. Section
AIR DUCT ACCESSORIES
SECTION 233300 - PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to
HVAC BASIC MATERIAL AND METHODS 1.01 RELATED CORNELL DESIGN AND CONSTRUCTION STANDARDS
230500 HVAC BASIC MATERIAL AND METHODS PART 1 GENERAL 1.01 RELATED CORNELL DESIGN AND CONSTRUCTION STANDARDS A. Section 230000 Basic HVAC Requirements B. Section 230523 Valves C. Section 230510 Chilled
D. NEMA Compliance: Provide electric motors and components which comply with NEMA standards.
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
A. General: Refer to paragraph entitled "SUBMITTAL" in Section Include the following data:
SECTION 15860 - FANS PART 1 - GENERAL 1.01 RELATED DOCUMENT A. Basic Requirements: Provisions of Section 15010, BASIC MECHANICAL REQUIREMENTS, and Section 15030, ELECTRICAL REQUIREMENTS FOR MECHANICAL
SECTION HYDRONIC PIPING SYSTEMS. 1. Pipe and pipe fittings are specified in the following sections:
SECTION 15510 HYDRONIC PIPING SYSTEMS A. RELATED SECTIONS 1. Pipe and pipe fittings are specified in the following sections: a. Section 15061, STEEL PIPE AND FITTINGS. b. Section 15062, COPPER AND COPPER
HYDRONIC SPECIALTIES TACO MPT Tank(s) 05/30/2012. A. Multi-Purpose Tank buffer tank, air separator, and hydraulic decoupler
SECTION 15181 - HYDRONIC SPECIALTIES PART 1 - GENERAL 1.1 SECTION INCLUDES A. Multi-Purpose Tank buffer tank, air separator, and hydraulic decoupler B. Expansion tanks C. Pump accessories 1.2 RELATED SECTIONS
PRICE BOOK CONTENTS 010 PIPE
010 PIPE 010 Buttweld Pipe 020 ERW 2-24 Pipe 030 Domestic Seamless Pipe 2-12 040 Domestic OD Seamless 14-24 Pipe 050 Pressure Pipe A106 060 Fusion Bond Pipe 080 Cut To Order Pipe 020 STAINLESS STEEL PIPE
DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC)
23 22 00 PART 1 - GENERAL 1.01 SYSTEM DESCRIPTION A. Steam Distribution System: Steam is the primary heat source for a variety of functions throughout the Pullman campus of Washington State University.
PROJECT NAME: DPW Idaho State University Liberal Arts Building Chiller Replacement
ADDENDUM NO.2 April 6, 2018 PROJECT NAME: DPW 18 223 Idaho State University Liberal Arts Building Chiller Replacement The data included hereinafter is issued by the Engineer (Engineered Systems Associates,
HVAC LEGEND HVAC ABBREVIATIONS PLUMBING LEGEND PLUMBING ABBREVIATIONS PRELIMINARY NOT FOR CONSTRUCTION
GENERAL NOTES SPECIFICATIONS LEGEND SYMBOL DESCRIPTION ABBREV. SYMBOL DESCRIPTION ABBREV. SYMBOL DESCRIPTION ABBREV. ABBREVIATIONS PLUMBING LEGEND SYMBOL DESCRIPTION ABB. SYMBOL DESCRIPTION ABB. SYMBOL
Part # Page Dampers Supported Directly From Structure 5. Dampers Supported From Ductwork Above 4
Part #453343 INSTALLATION INSTRUCTIONS DAMPERS AND LOUVERS CRD Series s These installation instructions apply to 3 hour rated ceiling radiation dampers mounted in a ceiling with supports from 1) a ceiling
A. ASME Compliance: Fabricate and install hydronic piping in accordance with ASME B31.9 "Building Services Piping.
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 233423 - HVAC POWER VENTILATORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 PERFORMANCE REQUIREMENTS A. Operating
B. HI Compliance: Design, manufacture, and install pumps in accordance with HI "Hydraulic Institute Standards."
PART 1: GENERAL 1.01 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design. The responsibility of the engineer is
DOCUMENT TABLE OF CONTENTS
DOCUMENT 00010 TABLE OF CONTENTS Section Title DIVISION 15 - MECHANICAL 15072 Vibration Isolation for HVAC Piping and Equipment 15076 Identification for HVAC Piping and Equipment 15081 HVAC Insulation
AIR DISTRIBUTION. C. Section Building Automation and Control System Guidelines. D. Section Fire Alarm System & Detection Systems
233100 AIR DISTRIBUTION PART 1: GENERAL 1.01 RELATED SECTIONS A. Section 230700 HVAC Insulation B. Section 237300 Air Handling C. Section 230900 Building Automation and Control System Guidelines D. Section
DARTMOUTH COLLEGE DESIGN March 15, 2003 & CONSTRUCTION GUIDELINES
SECTION 15830 HEATING & COOLING TERMINAL UNITS PART 1 DESIGN DIRECTIVES 1.1 DESIGN CRITERIA A. All fan coil units shall be sized to meet design load while operating at medium speed. In extreme noise sensitive
UNIVERSITY OF ROCHESTER DESIGN STANDARDS NOVEMBER 1, 2013
SECTION 15800 - AIR HANDLING EQUIPMENT 1.1 GENERAL A. All air handlers installed shall conform to the University of Rochester specification Guideline for Semi-Custom and Pre-Engineered Air Handling Units.
D. Fabrication: Steel or Aluminum with baked enamel off-white finish. B. Type: Square and rectangular, adjustable pattern, multi-louvered diffuser.
SECTION 23 37 00 - AIR OUTLETS AND INLETS PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Diffusers. 2. Registers 3. Grilles. PART 2 - PRODUCTS 2.1 ROUND CEILING DIFFUSERS B. Product Description:
.2 Section Waste Management and Disposal..5 Section Motors, Drives and Guards for Mechanical Systems.
Issued 2006/08/01 Section 15131 Pumps Hydronic Systems Page 1 of 6 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01330 Submittal Procedures..2 Section 01355 Waste Management and Disposal.3 Section 01780
Division 23 - HVAC Switzerland Beallsville K-12. Section HYDRONIC PIPING SECTION HYDRONIC PIPING PART 1 - GENERAL
Division 23 - HVAC 090070 Switzerland Beallsville K-12 Section 23 21 13 HYDRONIC PIPING SECTION 23 21 13 HYDRONIC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the
PhiloWilke Partnership Addendum No. 2 A/E Project No April 2016
SECTION 23 21 23 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General Conditions and Division 01 Specification Sections, apply to this Section.
Wayne State University WSU Project No Chatsworth Tower Apts. Misc. Bldg. Upgrades DSD Project No
SECTION 213113 - ELECTRIC-DRIVE, CENTRIFUGAL FIRE PUMPS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
FM 517 San Leon, TX Toll Free: Office: (281) Fax: (281)
www.rbmosherco.com 5902 FM 517 San Leon, TX 77539 Toll Free: 1-800-444-2207 Office: (281) 339-3382 Fax: (281) 559-1152 E-mail: sales@rbmosherco.com R.B. MOSHER CO. has been in business since 1986, providing
TECHNICAL. Series 18. Pump Packages
TECHNICAL S Y S T E M S Series 18 Pump Packages Series 18 Pump Packages Standard Features Close-coupled, end-suction, centrifugal pumps Mounted and wired pump starters Hand-Off-Auto switch for each pump
B E ROUTE DUCT BEHIND BOOKSHELF. GRILLE MOUNTED ON TOP OF BENCH. BOOK CASE WALL 12x8 8x5 I 8"Ø 7"Ø 125 CFM I D M FLOOR SIDE WALL VENT 6x5 160 CFM 6"Ø 6"Ø 8x10 J C G 1 Section M-1 NOT TO SCALE Project No
SECTION HYDRONIC PIPING
SECTION 23 21 13 HYDRONIC PIPING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes pipe and fitting materials, joining methods, special-duty valves, and specialties for the following: 1. Hot-water
SECTION (15820) - AIR DUCT ACCESSORIES
PART 1 GENERAL 1.01 SUMMARY A. Section includes: SECTION 23 33 00 (15820) - AIR DUCT ACCESSORIES 1. Manual-Volume Dampers 2. Fire Dampers 3. Turning Vanes 4. Duct-Mounted Access Doors 5. Flexible Connectors
SECTION DUCTWORK
PART 1 GENERAL 1.1 REFERENCES SECTION 23 31 00 DUCTWORK A. ASHRAE - Handbook, Duct Design B. ASHRAE - Handbook, Duct Construction C. ASTM A90/A90M - Standard Test Method for Weight (Mass) of Coating on
C. ASSE 1013: Performance Requirements for Reduced Pressure Principle Backflow Preventers.
SECTION 22 10 00 PLUMBING PIPING AND PUMPS PART 1 - GENERAL 1.1 Purpose: A. This standard is intended to provide useful information to the Professional Service Provider (PSP) to establish a basis of design.
A. This Section includes the following fire-suppression piping inside the building:
SECTION 211000 - WATER-BASED FIRE-SUPPRESSION SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following fire-suppression piping inside the building: 1. Automatic wet-type, standpipe systems.
SECTION HVAC TABLE OF CONTENTS PART 1 - SYSTEM DESCRIPTION / OUTLINE SPECIFICATIONS FILED SUB BID PROJECT OVERVIEW...
SECTION 230001 TABLE OF CONTENTS SECTION 230001 PART 1 - SYSTEM DESCRIPTION / OUTLINE SPECIFICATIONS... 1 1.00 FILED SUB BID... 1 1.01 PROJECT OVERVIEW... 2 1.02 DESIGN CRITERIA... 4 1.03 CODE ISSUES...
DESIGN GUIDELINES SECTION HVAC
3/15/17 Cooling Methodology Chiller Plants Configurations monitoring Preferred DESIGN GUIDELINES SECTION 15700 HVAC Air-cooled chillers < or = 300 tons; water-cooled chillers > 300 tons Variable volume
SHOE PALACE HUNTINGTON PARK M.200
M.200 SPLIT SYSTEM CONDENSING UNIT SCHEDULE MARK SERVICE MODEL NO. COOLING DIMENSIONS ELECTRICAL REMARKS CAPACITY AMBIENT DB REFRIGERANT LENGTH WIDTH HEIGHT WEIGHT VOLT/PHASE MCA MOP (MBH) (DEG F) (IN)
Union County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 22 40 00 - PLUMBING FIXTURES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Faucets for lavatories, bathtubs, bathtub/showers, showers and sinks. 2. Flushometers. 3. Toilet
SECTION DUCTWORK
SECTION 15890 DUCTWORK PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 07270 - Firestopping and Fire and Smoke Barrier Caulking. 2. 15260 - Vibration Isolation. 3. 15280 - Thermal Insulation (HVAC).
CONTENTS. B. System Design and Performance Requirements
15815 Metal Ducts This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications or in notes
B. System Design and Performance Requirements
15815 Metal Ducts This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications or in notes
DIVISION 15 MECHANICAL
DIVISION 15 MECHANICAL A. GENERAL DESIGN CONDITIONS 1. Design occupied spaces to maintain 72 F and a space dew point temperature not to exceed 55 F. 2. Design classroom and office space buildings with
DRAWING SCHEDULE TAB REQUIREMENTS BY EQUIPMENT TYPE TYPE OF EQUIPMENT DESCRIPTION COMPONENT TAB REQUIREMENTS
DRAWING SCHEDULE NUMBER TITLE M0-1 MECHANICAL NOTES AND LEGEND M1-0 MECHANICAL FLOOR PLAN M4-0 MECHANICAL SCHEDULES M4-1 MECHANICAL LOAD CALCULATIONS M5-0 MECHANICAL DETAILS M8-0 TCS BASYS CONTROLS DRAWINGS
Eureka - Fall Maintenance Crew 2017 List of material for plumbing works for sealift 2017
Eureka - Fall Maintenance Crew 2017 List of material for plumbing works for sealift 2017 Item Location /Description Ref Qty Price EOB-M23A General Mechanical Division 23 New Garage, Water Heater 1 3/4
DIVISION 23 - HVAC HVAC Air Distribution
PART 1 - GENERAL 1.01 GENERAL CRITERIA A. General Design Criteria 1. System standards require that buildings be fully ducted (supply, exhaust and return air). 2. Provide positive exhaust ventilation for
University of Delaware
University Contact: Energy & Engineering Group (302) 831-1744 SECTION 23 73 00_AIR HANDLING UNITS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Modular custom & semi-custom built indoor air handling
DIVISION 23 - HVAC HVAC Air Distribution
PART 1 - GENERAL 1.01 GENERAL CRITERIA A. General Design Criteria 1. System standards require that buildings be fully ducted (supply, exhaust and return air). 2. Provide positive exhaust ventilation for
A. Product Data: Include rated capacities, operating characteristics, furnished specialties, and accessories.
Page 238219-1 SECTION 238219 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
Square Ceiling Diffusers : All extruded aluminum constructions. Opposed blade damper is adjustable from face of diffuser. Available in square and
Square Ceiling Diffusers : All extruded aluminum constructions. Opposed blade damper is adjustable from face of diffuser. Available in square and rectangular type with one, two, three or four way patterns.
Domestic Pump Condensate Transfer Equipment
Bulletin S-944L Domestic Pump Condensate Transfer Equipment CONDENSATE RETURN UNITS BOILER FEED UNITS LOW NPSH PUMPS VACUUM HEATING UNITS INDUSTRIAL VACUUM UNITS www.domesticpump.com Condensate Return
Brown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION AIR HANDLING UNITS
SECTION 23 70 00 AIR HANDLING UNITS PART 1. GENERAL 1.1 Section includes air-handling units to 15,000 cfm and accessories. 1.2 Related Sections 1 : A. Division 01 - Brown University Standard for Narragansett
Water Piping and Pumps
Technical Development Program DISTRIBUTION SYSTEMS Water Piping and Pumps PRESENTED BY: Michael Ho carriertdp@gmail.com 424-262-2144 Menu Section 1 Section 2 Section 3 Section 4 Section 5 Section 6 Section
1.1 This section applies to air handling units for HVAC Systems.
AIR HANDLING UNITS GENERAL INFORMATION 1.1 This section applies to air handling units for HVAC Systems. DESIGN REQUIREMENTS 2.1 Design Criteria a. The decision to use modular central station air handling
Florida Department of Transportation
Page 1 of 7 RICK SCOTT GOVERNOR Florida Department of Transportation 1109 S. Marion Avenue Lake City, Florida 32025 ANANTH PRASAD SECRETARY September 27, 2011 To: Proposal Holders Addendum No: 1, E2Q23,
CONTENTS. A. Summary. Yale University Design Standards. Valves. Change History
Change History Change Date Description of Change Pages / Sections Modified Approver Initials 3/26/13 Add next item; do not use mechanical coupling components. 3/26/13 Add next item; do not use mechanical
SECTION METERS AND GAGES
Buchtel/PerIcins Community Learning.Center GPD - 2007271.15 SECTION 15122 METERS AND GAGES PART 1- GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and
DENVER PUBLIC SCHOOLS DESIGN AND CONSTRUCTION STANDARDS This Standard is for guidance only. SECTION EXHAUST FANS
PART 0 A/E INSTRUCTIONS 0.01 DESIGN REQUIREMENTS A. Placement within a mechanical room is required for all major mechanical equipment. Only small units may be roof-mounted, and shall be made as inconspicuous
SECTION AIR OUTLETS AND INLETS
SECTION 23 37 00 AIR OUTLETS AND INLETS PART 1 - GENERAL 1.1 SUMMARY A. Section includes diffusers, light troffer diffusers, registers/grilles, door grilles, louvers, louvered penthouses, roof hoods, goosenecks.
UNIVERSITY OF MISSOURI Fire Protection System Design 2016 Q1
GENERAL: 1. All fire protection systems shall be installed in accordance with the International Fire Code and applicable NFPA standards. This guideline provides additional requirements for the design and
TABLE OF CONTENTS DIVISION 23 MECHANICAL
TABLE OF CONTENTS DIVISION 23 MECHANICAL 23 00 00...2 23 00 01 GENERAL...2 23 00 02 REFERENCES, REGULATORY REQUIREMENTS...2 23 00 03 REFERENCES, RELATED SECTIONS of the SPECIFICATIONS...2 23 00 04 DEFINITIONS...2
2016 CDM Smith All Rights Reserved July 2016 SECTION PLUMBING - EQUIPMENT
PART 1 GENERAL 1.01 SCOPE OF WORK SECTION 22 30 00 PLUMBING - EQUIPMENT A. Furnish all labor and materials required and install the following Plumbing Equipment complete as specified herein and as shown
BuildingName The Description of the Project P DOCUMENTS
ARCHITECTURE, ENGINEERING AND CONSTRUCTION P00000000 0000 DOCUMENTS ARCHITECTURE & ENGINEERING 326 East Hoover, Mail Stop B Ann Arbor, MI 48109-1002 Phone: 734-764-3414 Fax: 734-936-3334 SPECIFICATION
SECTION PLUMBING EQUIPMENT
PART 1 GENERAL 1.01 SECTION INCLUDES A. Water heaters. B. Packaged water heating systems. C. Domestic water heat exchangers. D. Water storage tanks. E. Water softeners. F. Reverse osmosis equipment. G.
D-8 OUTLINE SPECIFICATION FOR HTHW HEAT EXCHANGERS
D-8 OUTLINE SPECIFICATION FOR HTHW HEAT EXCHANGERS GENERAL: This document provides performance requirements and guideline information for Heat Exchanger equipment for Colorado College only, and is not
SECTION CONVECTION HEATING AND COOLING UNITS
PART 1 GENERAL 1.01 SECTION INCLUDES A. Baseboard radiation. B. Finned tube radiation. C. Convectors. D. Unit heaters. E. Cabinet unit heaters. F. Fan-coil units. G. Unit ventilators. H. Blower-coil units.
Construction Standards Page Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA
Construction Standards Page 233423-1 Copyright 2009 by The American Institute of Architects (AIA) Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA Modified
Ratio Architects, Inc. Section Refrigerant Piping
SECTION 232300 - REFRIGERANT PIPING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Refrigerant pipes and fittings. 2. Refrigerant piping valves and specialties. 3. Refrigerants. 1.2 ACTION SUBMITTALS
SAFETY PLUMBING PACKAGES. Quality Products & Value Packages SUSTAINABILITY. Residential Solutions ANTI-SCALE SYSTEMS FIRE PROTECTION
Quality Products & Value Packages Residential Solutions FIRE PROTECTION COMFORTSUSTAINABILITYCONTROL PRESSURE REGULATORS TRENCH DRAINSHVAC SYSTEMS SAFETY ANTI-SCALE SYSTEMS HEATING & COOLING CONTROLS PLUMBING
Baltimore Manufacturer Line Card
Baltimore Manufacturer Line Card 12500 Baltimore Avenue, Unit F; Beltsville, MD 20705 301-918-0241 www.hbproducts.com abi Airbalance www.airbalance.com AJ Manufacturing www.ajmfg.com American Louver www.americanlouver.com
15900 HVAC INSTRUMENTATION AND CONTROLS
15900 HVAC INSTRUMENTATION AND CONTROLS PART 1 GENERAL - Andover Controls BAS system is the standard for the University, and may be specified as a proprietary item. 1.0 RELATED DOCUMENTS A. Drawings and