PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017

Transcription

1 CCA 1422 NEW S.T.E.M. BUILDING 2017 SECTION KITCHEN AND CAFETERIA EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section. 1.2 SUMMARY A. This section will include equipment for the following areas: 1. Kitchen Equipment 2. Cafeteria Equipment 3. Teacher s Room Equipment 4. Dining Room Equipment 1.3 COORDINATION A. Coordinate installation : 1. Provide all equipment with the necessary connections for installation by the General Contractor, to electric, gas, venting, etc. 2. Coordinate utility supply, waste, and venting with the mechanical and electrical requirements of this project. 3. Confirm electrical requirements, including but not limited to voltage and amperage ratings for the equipment supplied for this project. PART 2 - PRODUCTS 2.1 GENERAL REQUIREMENTS A. Comply with requirements in this Section except when stricter requirements are specified in equipment schedules or Sections. B. Comply with all applicable codes. 2.2 EQUIPMENT A. Provide equipment listed below or Architect approved equal. 1. Kitchen Equipment: See cut sheets attached at the end of this specification section for basis of design of equipment 2. Cafeteria Equipment: See cut sheets attached at the end of this specification section for basis of design of equipment 3. Teacher s Room Equipment: See cut sheets attached at the end of this specification section for basis of design of equipment 4. Dining Room Equipment: See cut sheets attached at the end of this specification section for basis of design of equipment PART 3 - EXECUTION (Not Applicable) END OF SECTION KITCHEN AND CAFETERIA EQUIPMENT

2 Quotation 01/10/2017 To: Project: From: NEW S.T.E.M. BUILDING 45 REINHARDT ROAD WAYNE,, NJ NEW S.T.E.M. BUILDING KITCHEN 45 REINHARDT ROAD WAYNE,, NJ BFA Foodservice Equipment Alex Nasarow 325 Division St Boonton, NJ (973) (Contact) (973) (Fax) Project Code: ANPCTIC1 Item Qty Description Sell Sell Total LOT OF EQUIPMENT FOR KITCHEN UPDATED 12/26/2016 ITEMS LISTED AS "ALTERNATES" ARE FOR FUTURE PURCHASE. MAIN COOKING AREA 1 1 ea ISLAND VENTILATION SYSTEM $114, $114, Captive Aire NJ Model No. 6030ND 2 PSP F A LOT OF HOOD SECTIONS: 6 CAPTIVEAIRE HOOD SECTIONS B LOT OF FIRE SYSTEM: ANSUL LIQUID SYSTEM MECHANICAL GAS VALVE C LOT OF EXHAUST FANS: 6 ROOF FANS WITH CURBS,EACH 2 HP 208V/3 PHASE D LOT OF HEATED SUPPLY UNITS: 2 GAS FIRED SYSTEMS 1 5 HP MOTOR 208 VOLT/3 PHASE 1 3 HP MOTOR 208 VOLT/3 PHASE WITH SEPARATE 120 VOLT WIRING E HOOD AND FANS CONTROL PACKAGE: 1 CONTROL PACKAGE FOR ALL HOODS,FANS AND SUPPLY UNITS F UTILITY DISTRIBUTION CENTER: FULL LENGTH OF HOODS BUILT IN SS. INCLUDES SEPARATE PLUMBING & ELECTRICAL TAKE OFFS CABINETS. SINGLE POINT CONNECTIONS. NOTE: REFER TO CAPTIVEAIRE REVISED DRAWINGS SHEETS 1 & 2 OF 2 FOR DETAILS. 2 3 ea HAND SINK $ $2, Init ial: Page 1 of 21

3 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total Advance Tabco Model No. 7 PS 65 Hand Sink, wall model, 14" wide x 10" front to back x 5" deep bowl, 304 series stainless steel, deck mounted fixed faucet, deck mounted soap dispenser, undermount towel dispenser, stainless steel construction, wall bracket, NSF, ccsaus 3 ea K 316 LUHA Wrist Handles Only, for splash or deck mount hand sink faucet (1 pair hot & cold 4" long blades), fits faucets supplied after November 2015 with hot & cold color rings that do not have exposed screw head 3 ea 7 PS 17B Welded Side Splash, 7 3/4" tall, both sides, for hand sinks with 10" x 14" bowl & deck mounted faucets 3 1 ea FRYER BATTERY, ELECTRIC $14, $14, Pitco Frialator Model No. SE14X 2FD Solstice Prepackaged Fryer System with Solstice Filter Drawer System, electric, (2) 50 lb. oil capacity full tanks, solid state controls, boil out & melt cycle, drain valve interlock, stainless steel tank, front & sides, under fryer drawer filtration, total 28.0kW ( FF), ENERGY STAR, UL, NSF, CE, GS 1 ea NOTE: Power supply for basket lifts and filter motor is hard wired at the factory for 208v, 240v models 1 ea 1 year parts and labor warranty from the date of installation up to a maximum of 15 months from the date of manufacture (with appropriate documentation), standard 1 ea (2) 208v/60/3 ph, 14 kw, DIRECT 1 ea Solid State Thermostat, standard 1 ea BNB SE14 Solstice Bread & Batter Cabinet, with BNB dump station, fryer match design, approximately 15 5/8" wide, standard finish, stainless steel front, sides & door, for prepackage system SE14 electric fryers, NSF 1 ea 3rd Position location for Bread & Batter dump station (FFB) 1 ea PFW 1 Food Warmer, built in, 750watt, CSA, NSF,UL 1 ea 120v/60/1 ph, 6.3 amps, 750 watts, NEMA 5 15P 1 ea P Basket, (2) oblong/twin size, 13 1/2" x 6 1/2" x 5 1/2" deep, long handle, regular mesh (shipped std (n/c) with models "T" SG14, SG14R, SSH55, SE14, SE14X, SE14B, SG14T, 35+, 45+, fryer batteries shipped with (1) per fryer 2 ea B Tank Cover, 18 gauge light duty, for models: SE14/14X/14R/14T/14TR/14TX/148/148R (with out basket lifts) 1 ea 9" legs, standard 2 ea Dormont 16100KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 4 2 ea HD RANGE, 36" FRENCH HOT TOP $9, $18, Init ial: Page 2 of 21

4 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total Vulcan Model No. V1FT36S V Series Heavy Duty Range, gas, 36", radial fin French top, standard oven, includes (1) oven rack, stainless steel front, front top ledge, sides, base, burner box & stub back, 6" adjustable legs, 95,000 BTU, CSA, NSF 2 ea 1 year limited parts & labor warranty, standard 2 ea Natural gas (add 1 suffix) (specify elevation if over 2,000 ft.) 2 ea PRESREG NA11/4 1 1/4" NPT pressure regulator (Natural gas) 2 ea 1 1/4" rear gas connection, standard 2 ea Rear gas connection: cap and cover, both ends 2 ea V36SFL Single deck flow thru hi shelf, non overlapping, 36" 2 st CASTERS RR4 Casters (set of 4) 2 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 5 1 ea CHARBROILER $8, $8, Magikitch'n Model No. FM RMB 648CR Radiant Charbroiler, floor model, gas, 48" wide, 34" high, free floating round rod top grate with EZ tilt to front grease trough, cast iron radiants, 95% stainless steel unit, 6" service shelf with utility bar, water tubs, open cabinet base, 6" adjustable legs, top grid scraper 1 ea 1 year limited parts and labor warranty, standard 1 ea Natural gas, specify elevation if over 2000 feet 1 ea High output burners, 200,000 BTU 1 ea Safety pilot shutoff 1 ea With lower rack, for use as a cheesemelter 1 ea NOTE: Unit requires a total of (2) steel and/or chrome grids 1 ea Stainless steel service shelf, 8" deep 1 ea Side & back extensions, stainless steel 1 ea Casters, (2) locking (set of 4) 1 ea Dormont 16100KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 6A 1 ea HD RANGE, 36", 4 OPEN BURNERS $9, $9, Vulcan Model No. V4B36S V Series Heavy Duty Range, gas, 36", (4) 33,000 BTU open burners, cast iron grates, standard oven, stainless steel front, front top ledge, sides, base, burner box & stub back, 182,000 BTU, 6" adjustable legs, CSA, NSF 1 ea 1 year limited parts & labor warranty, standard 1 ea Natural gas (add 1 suffix) (specify elevation if over 2,000 ft.) 1 ea PRESREG NA11/4 1 1/4" NPT pressure regulator (Natural gas) 1 ea 1 1/4" rear gas connection, standard 1 ea Rear gas connection: cap and cover, both ends Init ial: Page 3 of 21

5 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total 1 ea V36DFL double deck flow thru hi shelf, non overlapping, 36" 1 ea CASTERS ADJRR4 Adjustable casters 1 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 6B 1 ea HD RANGE, 36", 4 OPEN BURNERS Vulcan Model No. V4B36S V Series Heavy Duty Range, gas, 36", (4) 33,000 BTU open burners, cast iron grates, standard oven, stainless steel front, front top ledge, sides, base, burner box & stub back, 182,000 BTU, 6" adjustable legs, CSA, NSF 1 ea 1 year limited parts & labor warranty, standard 1 ea Natural gas (add 1 suffix) (specify elevation if over 2,000 ft.) 1 ea PRESREG NA11/4 1 1/4" NPT pressure regulator (Natural gas) 1 ea 1 1/4" rear gas connection, standard 1 ea Rear gas connection: cap and cover, both ends 1 ea V36DFL double deck flow thru hi shelf, non overlapping, 36" 1 ea CASTERS ADJRR4 Adjustable casters 1 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 7 4 ea FILLER WORK TABLE $1, $6, Advance Tabco Model No. VKS 363 Work Table, 36"W x 36"D, 14 gauge 304 series stainless steel top with countertop non drip edge, 10" backsplash, adjustable stainless steel undershelf, stainless steel legs & adjustable bullet feet, NSF 4 st TA 25 Casters, 5", swivel, with rubber wheels (set of 4) (2 with brakes) 4 ea SS 2020 Deluxe Drawer, 20"W x 20"D x 5" deep drawer pan insert, stainless steel, with drawer slides 8 1 ea TILTING GAS STEAM KETTLE Cleveland Range Model No. KGL25T Kettle, gas, tilting, 25 gallon capacity, 2/3 steam jacket design, floor mounted control console supports, stainless steel exterior finish, standard with flanged feet, 50 psi rating, electronic spark ignition, cover & draw off optional, 90,000 BTU 1 ea 1 year limited warranty, standard 1 ea Natural Gas 1 ea 120v/60/1 ph, 5.0 amp, electronic spark ignition, cord & plug for controls, standard 1 ea TD2 2" tangent draw off valve with strainer 1 ea CHS25 Spring assisted cover (25 gallon) 1 ea DPKT Double Pantry Faucet, with swing spout & mounting bracket for tilting kettles Init ial: Page 4 of 21

6 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total 1 ea PCK Pan Carrier, for all floor model kettles 25 gal & larger except KDM 25 T 1 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 9 1 ea TILTING GAS STEAM KETTLE $33, $33, Cleveland Range Model No. KGL60T Kettle, gas, tilting, 60 gallon capacity, 2/3 steam jacket design, with floor mounted control console supports, stainless steel exterior finish, standard with flanged feet, 50 psi rating, electronic spark ignition, cover & draw off optional, 190,000 BTU 1 ea 1 year limited warranty, standard 1 ea Natural Gas 1 ea 120v/60/1 ph, 10.0 amp, electronic spark ignition, cord & plug for controls, standard 1 ea TD2 2" tangent draw off valve with strainer 1 ea CHS60 Spring assisted cover (60 gallon) 1 ea DPKT Double Pantry Faucet, with swing spout & mounting bracket for tilting kettles 1 ea PCK Pan Carrier, for all floor model kettles 25 gal & larger except KDM 25 T 1 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 10 1 ea TILTING SKILLET, GAS $19, $19, Cleveland Range Model No. SGL40TR DuraPan Tilting Skillet, gas, 40 gallon capacity, modular open base, standard with electric tilt mechanism, stainless steel construction, includes spring assisted cover, gallon markings and electronic spark ignition, food strainer, stainless steel level adjustable feet, 130,000 BTU, CE, NSF 1 ea 1 year limited warranty, standard 1 ea Natural Gas 1 ea 120v/60/1 ph, 1.8 amp, standard 1 ea PT1 Power Tilt, with hand tilt override 1 ea TD2SK 2" tangent draw off valve, front mounted left side, includes FSSK strainer 1 ea PCS Pan Carrier, for floor models 1 ea DPK14 Double Pantry Faucet with, 3/4" swing spout & bracket 1 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty Init ial: Page 5 of 21

7 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total FLOOR TROUGHS AT POT WASH AREA AND COOKING AREA 11 4 ea FLOOR TROUGH $3, $12, Advance Tabco Model No. FTG 1872 Floor Trough, 18"W, 72"L, 4"D, 14 gauge 304 series stainless steel, includes stainless steel subway grating constructed from 3/16" x 1" bars, 4" O.D. waste pipe 3"L, pitched towards waste 4 ea FT 2 Replacement Strainer Basket, 4" x 4" x 4", for floor trough 24 ft FT 1 Anti Splash Guard, factory installed (per linear foot) 4 ea FT 4 Modify trough drain outlet size (2 minimum to 8 maximum diameter, 4 is standard) or drain location (For troughs 96 & longer, must order (2) each) 24 ft FT 5 Upgrade trough grate to have ADA openings (7/16 gap) (per linear foot) (must match length of trough, for odd lengths use next larger foot increment) 11A 1 ea FLOOR TROUGH $1, $1, Advance Tabco Model No. FTG 1830 Floor Trough, 18"W, 30"L, 4"D, 14 gauge 304 series stainless steel, includes stainless steel subway grating constructed from 3/16" x 1" bars, removable stainless steel strainer basket, 4" O.D. waste pipe 3"L, pitched towards waste 1 ea FT 2 Replacement Strainer Basket, 4" x 4" x 4", for floor trough 3 ft FT 1 Anti Splash Guard, factory installed (per linear foot) 3 ft FT 5 Upgrade trough grate to have ADA openings (7/16 gap) (per linear foot) (must match length of trough, for odd lengths use next larger foot increment) 12 1 ea BOILERLESS STEAMER $22, $22, Cleveland Range Model No. (2) 22CGT66.1 SteamChef 6 Convection Steamer, Gas, boilerless, double stacked, on ES equipment stand, (6) full size pan capacity per compartment, 60 minute electro mechanical timer & manual (continuous steaming) by pass switch, left hand hinged door, controls on right, automatic drain & water level controls, KleanShield interior, standard treated & tap water connection, stainless steel exterior, 4" adjustable legs with flanged feet, (2) 32,000 BTU, UL, NSF, ENERGY STAR 1 ea 1 year limited warranty, standard 1 ea Natural Gas 1 ea (2) 115v/60/1 ph, 4.0 amps each, standard 1 ea CWT 06 Claris Water Treatment System, includes (1) pre filter, (1) Claris X large steam system, (1) Claris flow meter and (1) water test kit (see water quality requirements in price list) 1 ea CWT XLC Claris X Large Filter Cartridge 1 ea EC 110 Claris EC 110 cartridge, pre filter replacement cartridge, for model CWT 06 1 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape Init ial: Page 6 of 21

8 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total and hardware mounting options, limited lifetime warranty 13 1 ea CONVECTION OVEN $16, $16, Blodgett Oven Model No. ZEPH 200 G ES DBL Zephaire Convection Oven, gas, double deck, bakery depth, capacity (5) 18" x 26" pans per compartment, solid state infinite controls with digital timer, two speed fans, flue connector, dependent glass doors, interior light, stainless steel front, sides and top, 6" stainless steel legs, 50,000 BTU each, ETL, CE, NSF, ENERGY STAR 1 ea NOTE: Draft diverter is not required for this oven 1 ea 2 year parts, 2 year labor and 1 additional year door warranty (parts only), standard 1 ea Natural gas 2 ea 115v/60/1 ph, 8.0 amps, 2 wire with ground, cord & plug, 3/4 hp (per deck), standard 1 ea SSI D Top Oven: Solid State infinite with digital timer, standard 1 ea SSI D Bottom Oven: Solid State infinite with digital timer, standard 2 ea Side shields, right hand side only, per deck 1 st 6" casters (set), in lieu of legs 1 ea NOTE: DO NOT deduct cost of standard legs 1 ea Gas manifold for double ovens 1 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 14 1 ea COMBI OVEN Groen Model No. (2)CBE 10GC ComboEase Combi Steamer/Oven, gas, boilerless, double stacked, (10) 18" x 26" full size sheet or (10) 12" x 20" full size hotel pan capacity per oven, semi automatic pre programmed cleansing, superheated steam, dual water connection, electronic timer, capacity (20) racks, hands free door latch, stainless steel construction with polished interior, stand with casters, 150,000 BTU 1 ea Everpure EV KleenSteam II Twin System, total system for boiler base steamers, 5.0 gpm flow rate, deliming (2) 7CB5 carbon filter, SS 10 scale inhibitor Cartridge, dip tube, pressure gauge, water shut off valve & wall bracket 1 ea Everpure Note: This system requires (2) cartridges. 1 ea 12 months parts and labor warranty, standard 1 ea Two year boiler warranty with PureSteem Water Filtration System 1 ea Natural gas 1 ea (2) 115v/60/1 ph, (2) 12.0 amps, direct 1 ea ELEV For elevation between 0 and 2000 (When order is placed, all equipment with elevation specified will be assigned a different Part# by the factory) 1 ea Door hinged on left, std. 1 ea Drain Tempering Valve, for 140 degree drain temperature requirement (requires 1/2" cold water connection), no electrical Init ial: Page 7 of 21

9 Item Qty Description Sell Sell Total connection required 1 ea Single Water Connection 2 ea Heat Shield, (1) per cavity, for CBE models 1 ea Faucet, double pantry, with 60" spray hose 4 ea Oven shelf, for ComboEase 2 ea French Fry Basket, full size, 18" x 26" x 1" 1 ea Chicken Rack 1 ea Chicken Drain Pan 2 ea Flue Diverter for double compartment 1 pk Delimer/Descaler, 1 pint bottle (8 pack) 1 pk Degreaser (4 pack) 2 ea Dormont 16125KIT2S48PS Dormont Blue Hose Moveable Gas Connector Kit, 1 1/4" inside dia., 48" long, covered with stainless steel braid, coated with blue antimicrobial PVC, 1 SnapFast QD, 2 Swivel MAX, 1 full port valve, 1 pair Safety Set with adhesive foam tape and hardware mounting options, limited lifetime warranty 15 2 ea WORK TABLE $1, $2, Advance Tabco Model No. VKS 303 Work Table, 36"W x 30"D, 14 gauge 304 series stainless steel top with countertop non drip edge, 10" backsplash, adjustable stainless steel undershelf, stainless steel legs & adjustable bullet feet, NSF 2 ea SS 2020 Deluxe Drawer, 20"W x 20"D x 5" deep drawer pan insert, stainless steel, with drawer slides JANITOR AREA 16 1 ea MOP SINK $2, $2, Advance Tabco Model No. 9 OP 48DF Mop Sink with Drop Front, floor mounted, 33"W x 25"D x 16"H (overall), 28"W x 20" front to back x 12" deep (bowl size), free flow drain with 2" IPS outlet, stainless steel construction 1 ea T&S Brass B 0363 Service Sink Faucet, wall mount, 8" centers, vacuum breaker, 6" wrist handles, built in stops 1 ea Note: This faucet is not intended for potable water use 1 ea K 242 Mop Hanger, 23", accommodates (3) 1 ea K 243 Mop Drainage Tray, stainless steel 1 ea DT 6R 36 Drainage Shelf, wall mount, tubular design, 36"W x 15"D x 8"H, stainless steel, KD LOCKER ROOM ea LOCKER Update International Model No. LKR 6BGA Packed 2 ea Locker, 6 tier, 12"W x 15"D x 78"H, adjustable legs, freestanding or attachable to other lockers, rugged steel, beige, ships assembled (2 each minimum order, freight only) SINK STATION BFA Foodservice Equipment 01/10/ ea THREE (3) COMPARTMENT SINK $5, $5, Init ial: Page 8 of 21

10 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total Advance Tabco Model No RL Regaline Sink, 3 compartment, with left & right hand drainboards, 28" front to back x 20"W sink compartments, 14" deep, with 11"H backsplash, stainless steel legs with welded front to rear & adjustable left to right cross rails, 24" drainboards, 1" adjustable bullet feet, 14 gauge 304 series stainless steel, overall 35" F/B x 115" L/R, NSF 3 ea K 15 Lever Waste Drain, twist handle operated with built in overflow, fits 3 1/2" drain opening, 2" NPT & 1 1/2" IPS outlet connections 3 ea K 4 Support Bracket, for lever waste drain handle, (1) support required for each lever drain 3 ea K 476 Punch hole for overflow drain, (1) punch required for each overflow drain, (please specify make & model of overflow used) (required for overflows unless using K 15) 1 ea T&S Brass B 0231 Sink Mixing Faucet, 12" swing nozzle, wall mounted, 8" centers on sink faucet with 1/2" IPS eccentric flanged female inlets, lever handles 1 ea T&S Brass B 0133 ADF12 BC EasyInstall Pre Rinse Unit, 8" wall mount, 12" swing nozzle, 44" stainless steel flex hose, 6" wall bracket, 1/4 turn compression cartridge, lever handle, stream regulator tip, add on faucet,.65 GPM spray valve, low lead, 1/2" NPT, EPAct2005 compliant, NSF (B 0107 C) 19 1 ea WORK TABLE WITH SINK(S) Advance Tabco Model No. DL Prep Table Sink Unit, 96"W x 30"D, 14 gauge 304 stainless steel top with (1) 16"W x 20"D x 4" deep sink bowl & (1) 16"W x 20"D x 8" deep sink bowl, (1) deck mounted goose neck faucet, Poly Vance sliding cutting board, 10"H back splash, no drip edge, stainless steel drawer, stainless steel legs & undershelf, adjustable stainless steel bullet feet, NSF 1 ea SS 2020 Deluxe Drawer, 20"W x 20"D x 5" deep drawer pan insert, stainless steel, with drawer slides 1 ea 12" wide 8 ea ODS Overshelf, table mounted, double, 96"W x 12"D, 18 gauge 430 series stainless steel (non adjustable, old style) 1 ea Center of table shelf location 1 ea T&S Brass MPY 2DCN 06 Mini Pre Rinse Unit, single hole deck base faucet, compact spring & flex hose, spray valve, 6" wall bracket, club handles, 6" add on faucet 20 4 ea WORK TABLE $1, $6, Advance Tabco Model No. SS 368 Work Table, 96"W x 36"D, 14 gauge 304 series stainless steel top, 18 gauge adjustable stainless steel undershelf, stainless steel legs & adjustable bullet feet, NSF 8 ea SS 2020 Deluxe Drawer, 20"W x 20"D x 5" deep drawer pan insert, stainless steel, with drawer slides 21 1 ea POT / KETTLE FILLER FAUCET $ $ Init ial: Page 9 of 21

11 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total T&S Brass Model No. B 0605 Pot & Kettle Filler Assembly, B 0068 H flex hose, wall mount, single control, vacuum breaker, 68"L flexible stainless steel hose, 4 arm handle & spray valve, hooked nozzle, 1/2" NPT female inlet 22 SPARE NO ea WIRE SHELVING $72.92 $ Metro Model No. 3036NK3 Super Erecta Super Wide Shelf, wire, 36"W x 30"D, plastic split sleeves are included in each carton, Metroseal 3 epoxy coated corrosion resistant finish with Microban antimicrobial protection 4 ea 74PK3 Super Erecta SiteSelect Post, 74 5/8"H, adjustable leveling bolt, posts are grooved at 1" increments & numbered at 2" increments, double grooved every 8", Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection 23 SPARE NO. 24 SPARE NO. FOOD PREP EQUIPMENT 25A 1 ea FOOD SLICER $6, $6, Globe Model No. 3850N Globe Premium Slicer, automatic, 2 speed, 40 & 60 strokes per minute, 13 diameter hardened steel alloy knife blade, gear driven knife system, start/stop touchpad controls, 2 angled drip groove on slice table, knife ring guard with removable deflector, knife cover interlock, & dual gear slice thickness adjustment, carriage angle 45, 12" food chute carriage, lift, pull & roll lift lever, stainless steel construction, 1/2HP, 115v/60/1 ph, 7.0amps, NEMA 5 15P, cetlus, NSF/ANSI (made in USA) 1 ea 1 year labor warranty from date of original installation (not to exceed 18 months from factory shipment) 1 ea 2 year parts warranty (excludes wear/expendable parts) 1 ea 15 year drive gears warranty (see Warranty sheet for complete details) 25B 1 ea FOOD SLICER Globe Model No. 3850N Globe Premium Slicer, automatic, 2 speed, 40 & 60 strokes per minute, 13 diameter hardened steel alloy knife blade, gear driven knife system, start/stop touchpad controls, 2 angled drip groove on slice table, knife ring guard with removable deflector, knife cover interlock, & dual gear slice thickness adjustment, carriage angle 45, 12" food chute carriage, lift, pull & roll lift lever, stainless steel construction, 1/2HP, 115v/60/1 ph, 7.0amps, NEMA 5 15P, cetlus, NSF/ANSI (made in USA) 1 ea 1 year labor warranty from date of original installation (not to exceed 18 months from factory shipment) 1 ea 2 year parts warranty (excludes wear/expendable parts) 1 ea 15 year drive gears warranty (see Warranty sheet for complete details) Init ial: Page 10 of 21

12 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total 26 1 ea PLANETARY MIXER Hobart Model No. HL600+BUILDUP Legacy Planetary Mixer, 60 qt, 2.7 hp, (4) fixed speeds plus stir speed, belt & gear driven transmission, Shift on the Fly controls, 40 minute SmartTimer, ergonomic swing out bowl, Hobart Quick Release agitators, power bowl lift, #12 attachment hub, stainless steel bowl guard, metallic gray electrostatic powder coat finish 1 ea Standard warranty: 1 Year parts, labor & travel time during normal working hours within the USA 1 ea HL /50/60/3/1 Mixer; without attachments; US/EXP configuration Legacy Planetary Mixer Unit Only, 2.7 HP, 60 qt. capacity, (4) fixed speeds, gear driven transmission, 50 Minute SmartTimer, #12 taper attachment hub, power bowl lift, stainless steel bowl guard 1 ea BOWL HL60 60 qt., Bowl, stainless steel 1 ea BBEATER HL60 60 qt.,"b" flat beater, aluminum 1 ea DWHIP HL60 60 qt., "D" Wire Whip, stainless steel 1 ea EDDOUGH HL60 60 QT. "ED" Dough Hook 1 ea PPASTRY HL60 60 qt. "P" Pastry Knife 1 ea CWHIP HL60 60 QT. "C" Whip 1 ea SPLASH LEX qt. Bowl Splash Cover, Lexan 1 ea TRUCK HL1486 Bowl Truck, for use with 60, 80 & 140 quart Legacy Mixers 27 1 ea PLANETARY MIXER Globe Model No. SP20 Planetary Mixer, bench model, 20 qt. 304 stainless steel bowl, #12 attachment hub, (3) fixed speeds, digital controls with 60 minute timer & batch recall, permanently lubricated gear driven transmission, removable & interlocking stainless steel bowl guard with built in ingredient chute, bowl lift, thermal overload protection, cast iron body, enamel gray paint, non slip rubber feet, includes: stainless steel wire whip, aluminum spiral dough hook & flat beater, 1/2 HP, 115v/60/1 ph, 6.0 amps, 6 ft cord with NEMA 5 15P, cetlus, NSF 1 ea 2 year parts (excludes wear/expendable parts), 1 year labor warranty (contact factory for details) 1 ea XXPASTRY 20 Pastry Knife, for 20 qt mixer, aluminum 1 ea XTABLE Mixer table w/undershelf, for the SP8, SP10, SP20 & SP25, 30"W x 24"D x 24"H, stainless steel top with galvanized steel undershelf & legs 28 1 ea ELECTRIC FOOD CUTTER $9, $9, Hobart Model No Food Cutter with #12 attachment hub, 18" diameter stainless steel bowl 20 RPM, double stainless steel knives 1725 RPM, bowl cover with safety interlock, push/pull on/off switch, one piece burnished aluminum housing, 3" legs, 115/60/1, 1 hp, 6' cord with plug 1 ea Standard warranty 1 Year parts, labor & travel time during normal working hours within the USA 29 1 ea MICROWAVE OVEN $1, $1, Init ial: Page 11 of 21

13 Item Qty Description Sell Sell Total Panasonic Model No. NE Pro I Commercial Microwave Oven, 2100 Watts, 0.6 cu. ft. capacity, 90 programmable memory pads, 15 power levels, left hinged door, stainless steel cabinet & cavity, digital display, cavity dimensions; 13"W x 12"D x 6 7/8"H, UL, ETL, NSF 1 ea 1 year parts, labor and travel/shipping warranty 1 ea 208v/60/1 ph, 16.6 amps, auto switch, NEMA 6 20P, standard 30 2 ea FOOD PROCESSOR $ $1, Waring Model No. WFP16SCD Combination Continuous Feed/Batch Bowl Processor, 4 qt. batch bowl & feed operation, LiquiLock seal system, heavy duty die cast housing, on, off and pulse push buttons, feed chute & chute cover, includes: dicing assembly, sealed S blade, adjustable slicing, reversible & sealed whipping discs, 2 HP motor, 120V/60/1 ph, NEMA 5 15P, ETLus, cetlus, ETL Sanitation 2 ea Standard warranty: 5 year motor and 2 year parts & labor 31 2 ea PANINI GRILL $ $1, Waring Model No. WPG250TB Panini Supremo Large Panini Grill, electric, single, 14 1/2" x 11" cooking surface, with timer, hinged auto balancing top plate with heat resistant handles, ribbed cast iron plates, adjustable thermostats 570 F (300 C), indicator lights, brushed stainless steel body & removable drip tray, 208v/60/1 ph, 13.5 amps, NEMA 6 20P, UL, NSF 2 ea Standard 1 year limited warranty 2 ea CAC105 Grill Brush, heavy duty, for all panini grills 32 1 ea MEGA TOP SANDWICH / SALAD PREPARATION REFRIGERATOR $5, $5, True Food Service Equipment Model No. TSSU 72 30M B ST Mega Top Sandwich/Salad Unit, (30) 1/6 size (4"D) poly pans, (2) stainless steel insulated covers, 8 7/8"D cutting board, stainless steel top, front and sides, aluminum back, (3) full doors, (6) shelves, aluminum interior with stainless steel floor, 5" castors, 1/2 HP, 115v/60/1, 10.3 amps, 7' cord, NEMA 5 15P, culus, UL EPH Classified, CE, MADE IN USA 1 ea Warranty 3 year parts and labor, please visit for specifics 1 ea Self contained refrigeration standard 1 ea Warranty 5 year compressor (self contained only), please visit for specifics 1 ea Double Overshelf, 72 3/8"L x 16"D x 33 1/32"H, for TSSU/TUC/TWT 72 & Mega, stainless steel 1 ea 5" Castors, standard POT/PAN CLEANING STATION BFA Foodservice Equipment 01/10/ ea WIRE SHELVING $71.35 $2, Metro Model No. 2460NK3 Super Erecta Shelf, wire, 60"W x 24"D, plastic split sleeves are included in each carton, Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection, NSF Init ial: Page 12 of 21

14 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total 32 ea 74PK3 Super Erecta SiteSelect Post, 74 5/8"H, adjustable leveling bolt, posts are grooved at 1" increments & numbered at 2" increments, double grooved every 8", Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection 34 1 ea DISHWASHER, POT/PAN/UTENSIL, DOOR TYPE Hobart Model No. PW20ER 1 Advansys Ventless Pot/Pan/Utensil Washer with Energy Recovery, front loading with split door design, (20) pan capacity, over/under rotating arms, 2/4/6 minute adjustable timer, up to (13) racks/hour, includes: (2) flat grids, (2) tray racks & (1) flat bottom rack, pre rinse spray hose, sanitizing with Sense A Temp 70 booster rise, internal condensing system, auto delime notification, vent fan control, stainless steel construction, v/60/3 ph, culus, NSF, ENERGY STAR 1 ea Standard warranty 1 Year parts, labor & travel time during normal working hours within the USA 1 ea DWT PW Drain water tempering kit 1 ea On site DWT installation by local Hobart Service Office (this price is available only if the local Hobart Service Office completes the installation of the dishwasher within a 50 mile radius & during normal business hours). Price is available only with machine purchase (if purchased separately local installation rates will apply) 1 ea WTRHAM ARREST Water hammer arrestor kit 1 ea PRESREG 3/4BR 3/4" brass pressure regulator 1 ea RACK STEAMPAN Steam Pan Rack 35 1 ea WASTE COLLECTOR Salvajor Model No. P914 Pot/Pan Scrap Collector, scrapping, pre flushing & collecting system (widely accepted in areas where disposers are restricted), NEMA 4 HYDROLOGIC control panel with patented operator sensor, two water saving modes (timed run & auto start/stop), safety line disconnect, LCD readout, salvage basin & silverware trap, scrap basket, 3/4 HP corrosion resistant pump, pump intake screen, stainless steel construction, UL, CSA, CE, NSF 1 ea 208v/60hz/1 ph, 5.5 amps 1 ea Additional scrap basket 36 1 ea SOILED DISHTABLE Advance Tabco Model No. DTS S30 84R Straight Soil Dishtable, right to left, 10 1/2"H backsplash, with prerinse sink, stainless steel legs with crossrails front to back, 83" long, 14/304 series stainless steel, Includes prerinse basket with slide bar (slide bar only when K 461 or K 461A disposer adapter is specified) 1 ea SEE #34 SPECIFY DISH MACHINE BRAND & MODEL to ensure proper fit, refer to attached document (AQ only) or consult for compatibility listing. Certain dish machines require modifications at additional cost not shown here 1 ea K 440 Waste trough, furnished with a 2" deep removable basket 1 ea DTA 95 Installation, scrapper top (S914, P914, PRP & PRS, top by others) Init ial: Page 13 of 21

15 Item Qty Description Sell Sell Total 1 ea T&S Brass B 1433 Hose Reel Assembly, enclosed hose reel, 30' hose with blue spray valve, wall mounted mixing faucet with 8" centers, includes vacuum and flexible supply hose, flanges with 1/2" NPT female inlets 1 ea DT 6R 13 Sorting Shelf, wall mounted, traditional design, 62"W, accommodates (3) full size dish racks, stainless steel, NSF 1 ea DTA 88 SLANT Provision for table mounted (slant) solid sorting shelf (cantilevered from backsplash) 1 ea DT 6R 11 Sorting Shelf, wall mounted, traditional design, 22"W, accommodates (1) full size dish rack, stainless steel, NSF 1 ea SPECIFY DISH MACHINE BRAND & MODEL to ensure proper fit, refer to attached document (AQ only) or consult for compatibility listing. Certain dish machines require modifications at additional cost not shown here 1 ea T&S Brass B 1433 Hose Reel Assembly, enclosed hose reel, 30' hose with blue spray valve, wall mounted mixing faucet with 8" centers, includes vacuum and flexible supply hose, flanges with 1/2" NPT female inlets 1 ea SPECIFY DISH MACHINE BRAND & MODEL to ensure proper fit, refer to attached document (AQ only) or consult for compatibility listing. Certain dish machines require modifications at additional cost not shown here 37 1 ea CLEAN DISHTABLE Advance Tabco Model No. DTC S30 72L Dishtable, clean, straight design, right to left operation, 10 1/2"H backsplash, 3" rolled front & side rims, stainless steel legs & crossrails, 71"W x 30"D x 34"H, 14/304 stainless steel 1 ea SPECIFY DISH MACHINE BRAND & MODEL to ensure proper fit, refer to attached document (AQ only) or consult for compatibility listing. Certain dish machines require modifications at additional cost not shown here 4 ft K 480 Shelf, 12" wide, stainless steel, (min. 3 ft.) (per linear foot) 1 ea DTA SS 54 Dishtable Undershelf, 54"W x 24"D, adjustable die cast leg clamps, stainless steel (size undershelf to be at least 6" shorter than dishtable) 1 ea TA gauge 304 series stainless steel undershelf upgrade (5 lin. ft.) VEGETABLE PREP AREA BFA Foodservice Equipment 01/10/ ea VEGETABLE PREP WORK TABLE WITH SINK(S) $3, $3, Advance Tabco Model No. DL Prep Table Sink Unit, 96"W x 30"D, 14 gauge 304 stainless steel top with (1) 16"W x 20"D x 4" deep sink bowl & (1) 16"W x 20"D x 8" deep sink bowl, (1) deck mounted goose neck faucet, Poly Vance sliding cutting board, 10"H back splash, no drip edge, stainless steel drawer, stainless steel legs & undershelf, adjustable stainless steel bullet feet, NSF 1 ea SS 2020 Deluxe Drawer, 20"W x 20"D x 5" deep drawer pan insert, stainless steel, with drawer slides Init ial: Page 14 of 21

16 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total 1 ea T&S Brass MPY 2DCN 06 Mini Pre Rinse Unit, single hole deck base faucet, compact spring & flex hose, spray valve, 6" wall bracket, club handles, 6" add on faucet 39 1 ea VEGETABLE DRYER Delfield Model No. SALD 1 Shelleymatic Salad Drier, capacity (20) gallons, stainless steel exterior & lid, polyurethane interior, unit completely enclosed, watertight motor, 1 1/2" drain, adjustable on/off timer with cycles up to 5 minutes, cord & plug included, 4" locking stem casters, 115v/60/1 ph, 2.7 amp, NEMA 5 15P, cul, UL, NSF 1 ea NOTE: Freight quotes are only valid from Delfield 1 ea 1 year parts & 90 day labor warranty, standard 1 ea Extra polyurethane liner & inner lid 40A 1 ea REACH IN REFRIGERATOR $3, $3, Traulsen Model No. G20010 Dealer's Choice Refrigerator, Reach in, two section, 46.0 cu. ft., selfcontained refrigeration with microprocessor control, stainless steel front & full height doors (hinged left/right), anodized aluminum sides & interior, (3) epoxy coated shelves per section (factory installed), 6" high casters, 1/3 HP, culus, NSF 1 ea 115v/60/1ph, 7.4 amps, NEMA 5 15P, standard 1 ea 3 year service/labor & 5 year compressor warranty, standard 40B 1 ea REACH IN REFRIGERATOR Traulsen Model No. G20010 Dealer's Choice Refrigerator, Reach in, two section, 46.0 cu. ft., selfcontained refrigeration with microprocessor control, stainless steel front & full height doors (hinged left/right), anodized aluminum sides & interior, (3) epoxy coated shelves per section (factory installed), 6" high casters, 1/3 HP, culus, NSF 1 ea 115v/60/1ph, 7.4 amps, NEMA 5 15P, standard 1 ea 3 year service/labor & 5 year compressor warranty, standard 41 1 ea MIXER, VERTICAL CUTTER VCM $6, $6, Robot Coupe Model No. R10 ULTRA Cutter/Mixer, vertical, bench style, 10 qt. capacity stainless steel bowl, 3.5 qt stainless steel mini bowl assembly, (3) "S" blades with smooth edges, magnetic safety switch, on/off & pulse control, indicator lights, (2) speed 1800/3600 RPM, v/60/3 ph, 11.8 amps, 4.5 HP, NEMA L15 20P, cetlus, ETL Sanitation 1 ea 1 year parts & labor warranty 42A 1 ea WORK TABLE $2, $2, Advance Tabco Model No. SKG 308 Work Table, 96"W x 30"D, 16 gauge 430 series stainless steel top with 5"H backsplash, 18 gauge stainless steel adjustable undershelf, stainless steel legs with adjustable bullet feet, NSF 1 ea TA 11B 2 Double Sink Welded Into Table Top, 16"W x 20"D x 12" deep bowls, includes faucet (must specify sink location) 2 ea K 5 Drain, twist operated, 2" NPT & 1 1/2" IPS outlet connections Init ial: Page 15 of 21

17 Item Qty Description Sell Sell Total 2 ea K 4 Support Bracket, for lever waste drain handle, (1) support required for each lever drain 1 ea SS 2020 Deluxe Drawer, 20"W x 20"D x 5" deep drawer pan insert, stainless steel, with drawer slides 1 ea T&S Brass B 0231 Sink Mixing Faucet, 12" swing nozzle, wall mounted, 8" centers on sink faucet with 1/2" IPS eccentric flanged female inlets, lever handles 42B 1 ea WORK TABLE Advance Tabco Model No. SKG 308 Work Table, 96"W x 30"D, 16 gauge 430 series stainless steel top with 5"H backsplash, 18 gauge stainless steel adjustable undershelf, stainless steel legs with adjustable bullet feet, NSF 1 ea TA 11B 2 Double Sink Welded Into Table Top, 16"W x 20"D x 12" deep bowls, includes faucet (must specify sink location) 2 ea K 5 Drain, twist operated, 2" NPT & 1 1/2" IPS outlet connections 2 ea K 4 Support Bracket, for lever waste drain handle, (1) support required for each lever drain 1 ea SS 2020 Deluxe Drawer, 20"W x 20"D x 5" deep drawer pan insert, stainless steel, with drawer slides 1 ea T&S Brass B 0231 Sink Mixing Faucet, 12" swing nozzle, wall mounted, 8" centers on sink faucet with 1/2" IPS eccentric flanged female inlets, lever handles 43 SPARE NO. 44 SPARE NO. 45 ITEM #45 REVISED TO INCLUDE THE CATERING COOLER PER ARCHITECT 1/10/2017 WALKIN COOLER/FREEZER BOXES BFA Foodservice Equipment 01/10/ ea WALK IN COOLER, SELF CONTAINED $31, $31, Master Bilt Products Model No. MB JO A INDOOR Walk In Cooler, 2 COOLER COMPARTMENTS, 1 CATERING,1 MAIN STORAGE. TOTAL 9' 8" x 33' 7 1/2" x 8' 6" high, with.080 textured aluminum floor, 26 gauge acrylic coated stucco galvanized steel interior & exterior, 4" thick pour type, foamed in place rigid urethane insulation, (2) 36" x 78" infitting entrance door. REMOTE SYSTEMS: 1 COMPRESSOR 1.3 hp, /60/ A. W/2 BLOWERS 115V/9 A. 1 COMPRESSOR 0.5 hp, /60/ A W/1 BLOWER 115V/9 A. 1 ea 18 month limited parts and labor on PRS 2 refrigeration systems, standard 1 ea 4 year extended compressor warranty, standard 1 ea 15 year panel warranty, standard 1 ea Door hinged on right main storage box 1 ea Door hinged on left catering box 1 ea Door size 36" x 78" Init ial: Page 16 of 21

18 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total 1 ea Master controller 2 ea Curtron M106 PR 4080 M Series Strip Door Kit for Walk In Coolers & Freezers, 40 wide x 80 high (fits openings up to 36 wide x 78 high), 6 wide x.060 thick polar reinforced clear PVC looped top strips (rated for 20 to 140 F), aluminum bar, and universal mounting brackets 46 1 ea WALK IN FREEZER SELF CONTAINED $18, $18, Master Bilt Products Model No. MB JO A INDOOR Walk In Freezer, 1 COMPARTMENT main storage. TOTAL 10' 7 1/2" x 17' 4" x 8' 6" high, with.080 textured aluminum floor, 26 gauge acrylic coated stucco galvanized steel interior & exterior, 4" thick pour type, foamed in place rigid urethane insulation, (1) 36" x 78" infitting entrance door. REMOTE SYSTEM: 1 COMPRESSOR 3 hp, /60/ A. W/1 BLOWER 208V/4 A. 1 ea 18 month limited parts and labor on PRS 2 refrigeration systems, standard 1 ea 4 year extended compressor warranty, standard 1 ea 15 year panel warranty, standard 1 ea Door hinged on left 1 ea Door size 36" x 78" 1 ea Master controller LOT OF WIRE SHELVING SEE ITEM LOCATION ITEM#48 SHELVING IN #45 MAIN COOLER AND CATERING COOLER ITEM#47 SHELVING IN #46 FREEZER ITEM#49 SHELVING IN DRY STORE ROOM ea WIRE SHELVING $82.82 $2, Metro Model No. 2460NK3 Super Erecta Shelf, wire, 60"W x 24"D, plastic split sleeves are included in each carton, Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection, NSF 36 ea 74PK3 Super Erecta SiteSelect Post, 74 5/8"H, adjustable leveling bolt, posts are grooved at 1" increments & numbered at 2" increments, double grooved every 8", Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection ea WIRE SHELVING $82.82 $6, Metro Model No. 2460NK3 Super Erecta Shelf, wire, 60"W x 24"D, plastic split sleeves are included in each carton, Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection, NSF 80 ea 74PK3 Super Erecta SiteSelect Post, 74 5/8"H, adjustable leveling bolt, posts are grooved at 1" increments & numbered at 2" increments, double grooved every 8", Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection ea WIRE SHELVING $82.82 $4, Init ial: Page 17 of 21

19 BFA Foodservice Equipment 01/10/2017 Item Qty Description Sell Sell Total Metro Model No. 2460NK3 Super Erecta Shelf, wire, 60"W x 24"D, plastic split sleeves are included in each carton, Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection, NSF 60 ea 74PK3 Super Erecta SiteSelect Post, 74 5/8"H, adjustable leveling bolt, posts are grooved at 1" increments & numbered at 2" increments, double grooved every 8", Metroseal 3 epoxy coated corrosionresistant finish with Microban antimicrobial protection 50 SPARE NO. 51 SPARE NO. 52 SPARE NO. 53 SPARE NO. 54 SPARE NO. BAKERY AREA 55 1 ea BAKER'S TABLE Advance Tabco Model No. TBS 308 Bakers Top Work Table, 96"W x 30"D, 1 3/4" thick wood top with 4" splash at rear & both sides, stainless steel legs with cross rails, stainless steel adjustable bullet feet, NSF 1 ea 12" wide 1 ea ODS Overshelf, table mounted, double, 96"W x 12"D, 18 gauge 430 series stainless steel (non adjustable, old style) 1 ea Rear of table shelf location, 1" back splash is provided on table with splash 56 1 ea PROOFER CABINET Metro Model No. C539 CDS UA C5 3 Series Heated Holding & Proofing Cabinet, with Red Insulation Armour, mobile, full height, insulated, Dutch insulated aluminum doors, removable bottom mount control module, thermostat to 200ºF, universal wire slides on 3" centers, adjustable on 1 1/2" increments (18) 18" x 26" or (34) 12" x 20" x 2 1/2" pan capacity, 5" casters (2 with brakes), aluminum, 120v/60/1 ph, 2000 watts, 16.7 amps, NEMA 5 20P, culus, NSF 1 ea Right hand hinging, standard 57 4 ea INGREDIENT BIN Cambro Model No. IBS27148 Ingredient Bin, mobile, 27 gallon capacity, 1 pc seamless polyethylene bin, 2 pc sliding polycarbonate lid, S hook on front (scoop NOT included), (4) 3" heavy duty casters (2 front swivel, 2 fixed), white with clear cover, NSF ea PAN RACK, BUN Init ial: Page 18 of 21

20 Item Qty Description Sell Sell Total Channel Manufacturing Model No. 401A Bun Pan Rack, standard, 70 1/4"H, 3" spacing, capacity (20) 18" x 26" bun pans, front loading, welded, heavy duty aluminum construction, 5" swivel plate caster, NSF (FLYER LIST PRICING) 59 1 ea TWO (2) COMPARTMENT SINK Advance Tabco Model No R Regaline Sink, 2 compartment, with right hand drainboard, 24" frontto back x 24"W sink compartment, 14" deep, with 11"H backsplash, stainless steel legs with welded front to rear & adjustable left toright cross rails, 36" drainboard, 1" adjustable bullet feet, 14 gauge 304 series stainless steel, overall 31" F/B x 92" L/R, NSF 2 ea K 15 Lever Waste Drain, twist handle operated with built in overflow, fits 3 1/2" drain opening, 2" NPT & 1 1/2" IPS outlet connections 2 ea K 4 Support Bracket, for lever waste drain handle, (1) support required for each lever drain 2 ea K 476 Punch hole for overflow drain, (1) punch required for each overflow drain, (please specify make & model of overflow used) (required for overflows unless using K 15) 1 ea Sink mounted 5 ft K 480 Shelf, 12" wide, stainless steel, (min. 3 ft.) (per linear foot) 5 ft K 499 Pot Rack, stainless steel, (per linear foot) 1 ea T&S Brass B 0231 Sink Mixing Faucet, 12" swing nozzle, wall mounted, 8" centers on sink faucet with 1/2" IPS eccentric flanged female inlets, lever handles 60 SPARE NO. 61 SPARE NO. HOT FOOD HOLDING CABINETS BFA Foodservice Equipment 01/10/ ea HEATED CABINET, MOBILE Metro Model No. C539 HLFC U C5 3 Series Heated Holding Cabinet, lower wattage, with Red Insulation Armour, mobile, full height, insulated, clear polycarbonate door, removable bottom mount control module, thermostat to 200ºF, universal wire slides on 3" centers, adjustable on 1 1/2" increments (18) 18" x 26" or (34) 12" x 20" x 2 1/2" pan capacity, 5" casters (2 with brakes), aluminum, 120v/60/1 ph, 1440 watts, 12 amps, NEMA 5 15P, UL, CUL, NSF 63A 1 ea HEATED CABINET, MOBILE $5, $5, Metro Model No. C5T8 DSB C5 T Series Transport Armour heavy duty insulated mobile heated cabinet, 5/6 height, adjustable bottom load slides 3 2/5" OC, top mount solid state digital controls with mobile power (14) 18" x 26" or (28) 12" x 20" x 2 1/2" pan capacity, 304 stainless steel, foamed inplace polyurethane insulation, maximum temperature 200 F, 6" casters, 120V/60/1, 1400 watts, 12 amps, NEMA 5 15P, culus, NSF, ENERGY STAR 63B 3 ea HEATED CABINET, MOBILE Init ial: Page 19 of 21

21 Item Qty Description Sell Sell Total Metro Model No. C5T8 DSB C5 T Series Transport Armour heavy duty insulated mobile heated cabinet, 5/6 height, adjustable bottom load slides 3 2/5" OC, top mount solid state digital controls with mobile power (14) 18" x 26" or (28) 12" x 20" x 2 1/2" pan capacity, 304 stainless steel, foamed inplace polyurethane insulation, maximum temperature 200 F, 6" casters, 120V/60/1, 1400 watts, 12 amps, NEMA 5 15P, culus, NSF, ENERGY STAR ROLL THRU COOLER/HOT BOX UNITS BFA Foodservice Equipment 01/10/ ea ROLL THRU HEATED CABINET $12, $12, Traulsen Model No. AIH232LP FHS Spec Line Heated Cabinet, Roll thru, two section, stainless steel exterior, aluminum interior, standard depth cabinet, full height doors, accepts 66" high racks (by others) with INTELA TRAUL, culus, NSF 1 ea 208/115v/60/1ph, 15.5 amps, 3000 watts, direct, standard 1 ea 3 year service/labor warranty, standard 1 ea Thermometer side: Left door hinged left/right hinged right, standard 1 ea Rear: Left door hinged left/right hinged right, standard 65A 1 ea ROLL THRU REFRIGERATOR $13, $13, Traulsen Model No. ARI232LPUT FHS Spec Line Refrigerator, Roll thru, two section, self contained refrigeration, stainless steel exterior, aluminum interior, standard depth cabinet, full height doors, accepts 66" high racks (by others) with INTELA TRAUL, 1/2 HP, culus, NSF 1 ea 115v/60/1ph, 13.4 amps, NEMA 5 20P, standard 1 ea 3 year service/labor & 5 year compressor warranty, standard 1 ea Thermometer side: Left door hinged left/right hinged right, standard 1 ea Rear: Left door hinged left/right hinged right, standard 65B 1 ea ROLL THRU REFRIGERATOR Traulsen Model No. ARI232LPUT FHS Spec Line Refrigerator, Roll thru, two section, self contained refrigeration, stainless steel exterior, aluminum interior, standard depth cabinet, full height doors, accepts 66" high racks (by others) with INTELA TRAUL, 1/2 HP, culus, NSF 1 ea 115v/60/1ph, 13.4 amps, NEMA 5 20P, standard 1 ea 3 year service/labor & 5 year compressor warranty, standard 1 ea Thermometer side: Left door hinged left/right hinged right, standard 1 ea Rear: Left door hinged left/right hinged right, standard 66 6 ea REFRIGERATOR RACK, ROLL IN $ $3, Channel Manufacturing Model No. 405AN HD Bun Pan Rack, heavy duty, nesting, 64"H, 2" spacing, capacity (17) 18" x 26" bun pans, front loading, welded aluminum construction, 5" swivel stem casters, NSF 6 ea ELC 65 Rack Cover, 63" 65"H, front & side load 67 SPARE NO. 68 SPARE NO. Init ial: Page 20 of 21

22 Item Qty Description Sell Sell Total 69 SPARE NO. 70 SPARE NO. 71 SPARE NO. 72 SPARE NO. BFA Foodservice Equipment 01/10/ A 1 ea ITEMS INCLUDED $4, $4, BFA Model No. FREIGHT Incoming freight from factory to BFA warehouse. 99B 1 ea ALTERNATE ITEMS BFA Model No. FREIGHT Incoming freight from factory to BFA warehouse. 100A 1 ea ITEMS INCLUDED NOW $8, $8, BFA Model No. DELIVERY BFA will deliver this equipment to the job site, uncrate and set all equipment in place. Made ready for final connections by OWNERS electrician and/or plumber. All work to be done during normal working hours by non union laborers. Removal of debris and existing equipment is not included. Site dumpster must be provided by GC. 100B 1 ea ALTERNATE FUTURE ITEMS BFA Model No. DELIVERY BFA will deliver this equipment to the job site, uncrate and set all equipment in place. Made ready for final connections by OWNERS electrician and/or plumber. All work to be done during normal working hours by non union laborers. Removal of debris and existing equipment is not included. Site dumpster must be provided by GC. Prices Good Until: 02/01/2017 Total $453, Acceptance: Printed Name: Project Grand Total: $453, Date: Init ial: Page 21 of 21

23 CCA 1422 NEW S.T.E.M. BUILDING 2017 SECTION PHYSICAL EDUCATION EQUIPMENT PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Basketball backstops and accessories. 2. Wall Pads. 3. Volleyball Equipment. 1.2 SUBMITTALS A. Submit in accordance with Section Submittal Procedures. 1. List of proposed products and product data. 2. Shop drawings showing layout, elevations, dimensions, fabrication details, method of attachment, loads to be transmitted to building structural members, requirements for supplementary bracing or structural support members and electrical wiring diagrams. 3. Manufacturer must provide calculations and reports for tests performed by an independent testing laboratory accredited by the American Association of Laboratory Accreditation (A2LA) that clearly demonstrate compliance with minimum safety factors included in product specifications. 4. Samples of fabric for selection by Architect. 5. Manufacturer's installation and maintenance instructions. 1.3 QUALITY ASSURANCE A. Source limitation: All components including suspension system, frame assembly, backboards, goals, electric winches, and controls for backstops shell be of a single manufacturer. B. All welding to be performed by personnel having passed Welder Qualification testing in accordance with American Welding Society (AWS) code D1.1 or higher. Manufacturer to provide certification and test results upon request. 1.4 DELIVERY, STORAGE, AND HANDLING A. Provide volleyball floor sleeves, covers and floor inserts in accordance with requirements of related trades that are responsible for installation. Do not deliver balance of athletic equipment until building is enclosed and other construction within gymnasium is substantially complete. 1.5 WARRANTY A. All Basketball Backstop support structures including clamps, fittings and tube to have a minimum warranty of 25 years from date of substantial installation. Warranty for other items to be as indicated in product specifications. PART 2 - PRODUCTS 2.1 ACCEPTABLE MANUFACTURERS PHYSICAL EDUCATION EQUIPMENT

24 CCA 1422 NEW S.T.E.M. BUILDING 2017 A. Base-of-Design. Draper, Inc., 411 South Pearl Street, Spiceland, Indiana ; Spalding 2. Bison 3. Or approved equal. 2.2 BASKETBALL BACKSTOPS A. Main Gym (Provide 2) 1. Type: Basketball backstop shall be equal to DRAPER EZ FOLD Model TF-20, ceiling-suspended, forward folding by Draper, Inc. of Spiceland, IN. Backstop shall be a welded together main frame constructed from steel mechanical tubing to form a rigid tetrahedral "T" design of back-to-back right triangles. The main stem shall be 6" OD 11-ga. steel tubing, the top of the "T" shall be 4" OD 11-ga. steel tubing and the side braces shall be 2-1/4" OD 14-ga. steel tubing. Side braces shall join stem no higher than 4'6" above goal (18" above top of backboard). The main stem shall be long enough to allow ±6" height adjustment of either fan or rectangular banks. The folding front brace shall be jackknife type, fully adjustable, self-locking in the down position and constructed of 2-1/2" OD 13-ga. (outer) steel tubing and 2-1/4" OD 14-ga. (inner) steel tubing. Pivot or hinge joint for folding of backstop shall not exceed 15" from roof structure except when required by architectural conditions for coordination with other trades or equipment. Pivot or hinge point to be designed in a manner to provide a minimum structural capacity of 25,000 Lbs. and a safety factor of 55:1. The main backstop frame shall pivot on 1-1/4" minimum solid steel shaft secured in a milled bearing hole in 1/2" minimum steel plate hangers to insure accurate positioning of bank. Bank attached to the 6" OD main stem by heavy-duty bank hangers. Hangers constructed of 1" x 2" 11-ga. steel tubing and formed 1/4" steel plate with slotted holes for lateral adjustment. All banks shall have one upper bank hanger and include a goal brace, which attaches directly to the goal mounting plate and directly to the 6" main stem of the backstop to eliminate any strain on the bank and help prevent glass breakage. This direct mount feature shall conform to NCAA recommendation No. 5-F. Backstop shall be supported from 4" OD 11-ga. steel mechanical tubing anchored to roof structure by means of heavy steel support hangers. Attachment to building structure to be with clamps capable of supporting a minimum of 20,000 Lbs. each. Superstructure shall be designed with a minimum of four attachment clamps to produce a combined minimum attachment point safety factor of 75 to 1 and manufacture must be able to present independent testing data to substantiate safety factor. Superstructure tubes shall be reinforced with bridging and/or bracing when truss centers exceed 10'0". Backstop shall be provided with custom powder coat RAL Color finish as selected by the Architect. 2. Operation: Main Gym (Provide 2) Winch is to be equal to DRAPER model no electric winch by Draper, Inc., Spiceland, IN Winch has a powerful ¾ HP, 115 volt, single phase, instant reverse motor with thermal overload protection that is governed to stall at 14 amps. Motor is rated at an intermittent 10 minute duty cycle. Winch motor operates at full load amperage rating of 11.5 full load amps. Winch has integral limit switches to stop travel in up and down positions. PHYSICAL EDUCATION EQUIPMENT

25 CCA 1422 NEW S.T.E.M. BUILDING 2017 Winch has an oil-bath gear case with precision ball bearings and premium seals for a lifetime of maintenance-free, leak free operation. Gear case features hardened steel gears that are securely captured to take on radial and thrust loads. Double worm gear reduction is in a ratio of 200:1 to provide exceptional holding power under load and eliminates the need for special or supplemental braking systems. Winch is specified to continuously run at the maximum rated load of 1250 lbs. (566 kilograms) for the motors rated duty cycle of 10 minutes without sustaining any gear damage. Winch has a large 4 ½ (114 mm) diameter cable drum that is helically grooved to accept ¼ 7 x 19 galvanized aircraft cable. Drum will accept up to 35 (10.7 meters) on a single layer and has a torsion spring tensioning roller to insure cable tracks properly into grooves, even if cable is allowed to go slack. Large diameter, grooves and tensioning spring provide long cable life and performance. Winch can be mounted in any orientation that allows for correct wrap direction and unobstructed cable travel which provides extreme flexibility during installation. Winch Assembly is covered by a five-year limited warranty and weighs just 68 Lbs. (30.8 kilograms) 3. Bank: Main Gym (Provide 2) Backboard shall be equal to DRAPER Model rectangular glass backboard by Draper, Inc. of Spiceland, IN. Backboard shall be 3'6" x 6'0" to meet all NCAA, NFHSA and professional requirements. Backboard frame of a heavy, brushed aluminum extrusion for maximum durability. Extended frame section of high tensile aluminum (6063-T5). Ends of the frame extrusions mitered and fitted with a flush, plated steel gusset type mounting bracket on all four corners, incorporating keyhole slots for mounting the backboard to the support structure at standard mounting centers. Goal mounting structure of a heavy, formed steel assembly, secured to the lower horizontal frame member to minimize stress on the glass section. Special steel sleeves at the goal mounting hole locations to secure rear structure to front mounting plate, forming a unitized assembly to minimize shock to the glass. Entire frame including goal-mounting structure fitted with a shock absorbing neoprene material to cushion and protect the glass section. 1/2" thick, fully tempered glass section with uniform load and impact strength. Official white border and target area is permanently fired into front side of glass section so that it cannot wear away. Goal mount structure provided with two holes (7/16") and two studs (3/8"-16) to secure backboard and goal to a direct mount "goal brace" feature which relieves all stress and shock on the backboard conforming to the latest NCAA Rules (BR-73, D-5). Goal mounting holes (4) to be standard 5" (horizontal) x 4" (vertical) mounting centers. Backboard shall be covered by a Lifetime Limited Warranty when installed on a Draper EZ Fold basketball backstop with Goal Brace or Direct Mount Height Adjuster. 4. Backboard Safety Padding: Main Gym (Provide 2) Backboard Edge Padding shall be equal to DRAPER Model 5032XX bolt-on backboard safety padding by Draper, Inc., Spiceland, IN. Molding process produces a super tough "skin" on the outside of the foam padding for long life. Pre-molded square corners for improved player safety. Molded-in steel track and bolt-on attachment system eliminate frustrating re-gluing or taping. Meets or exceeds all NCAA and High School Federation specifications. NCAA approved gray color. (Also available: Royal Blue, Scarlet, PHYSICAL EDUCATION EQUIPMENT

26 CCA 1422 NEW S.T.E.M. BUILDING 2017 Navy, Columbia Blue, Kelly Green, Gold, Forest Green, Orange, Purple, Black, and Maroon.) 5- year warranty when installed indoors. 5. Goal: Main Gym (Provide 2) Goal shall be equal to DRAPER Model breakaway goal by Draper, Inc. of Spiceland, IN. Goal shall be designed to withstand shock loads due to a player slam dunking and/or hanging on the rim. The rim shall deflect down when a static load of 230 pounds is applied. The rim will return to the playing position once the load is removed. The function of the breakaway goal shall meet NCAA specifications, which state: "A movable basket ring shall have rebound characteristics identical to those of a non-moveable ring." Goal shall be set at factory for proper flex and rebound requirements. Rim shall be fabricated from a 5/8" diameter steel rod formed into an 18" inside diameter ring. Inside of ring shall be positioned 6" from the face of backboard by a heavy-duty mounting plate with mounting holes centered to match 5" x 5" or 5" x 4" backboard mounting holes. Goal will mount on standard glass, fiberglass, aluminum, steel, and wood backboards. Rim shall be rigidly braced by means of die cut steel braces formed and welded to underside of rim for maximum support. Goal shall be provided with twelve "no tie" net attachment clips, welded to rim for net attachment. Goal shall be painted in an official durable orange powder coat. Goal shall be furnished with zinc plated mounting hardware and high quality white nylon anti-whip net. The top half of the anti-whip net is made of durable fibers encased in tough 100% nylon, preventing the net from whipping up on the rim. The lower half is all nylon. Goal to have three-year limited warranty. 6. Controls: Main Gym (Provide (1) Smart Gym Control Panel and System) Group Control System shall be equal to DRAPER Model SMART GYM Control System by Draper, Inc of Spiceland, IN- Smart Gym to Control All Backstop Winches and All Height Adjusters. Smart Gym Group Controller is to be able to control Basketball Backstops with Electric Winches, Electric Height Adjusters and other Auxiliary Devices from a centralized location. Group Control Systems to have 120V control processor that is fully programmable to operate gymnasium equipment and auxiliary devices provided by others. Group Control System must be capable of operating up to 1000 devices and can be programmed to operate single devices or groups of up to two devices simultaneously. Devices are controlled via 120V relay panels that may be mounted at remote location(s.) Each relay panel includes 8 relays. Devices that operate in an up/down or in/out cycle require two relays; devices that operate in an on/off cycle require one relay. Communications between processor and the relay panel(s) is 24V. User interacts via a 24V flush mounted graphical color touch screen to be custom programmed to match the project conditions. Touch screen to require entry of four-digit security code prior to accessing control screens. Security code is to be fully programmable by the user. Touch screen should be mounted in full view of equipment being operated and a minimum of one touch screen should be each room with equipment being operated. Complete control system to include one pre-programmed Model control processor and power supply in 18" x 18" x 6" surface mounted enclosure, the required number of Model relay panels (Provide 1) in surface mounted 15" x 8" x 2" surface mounted enclosure and the requested number of Model color touch screen (provide 1) to be mounted in 4 ½" x 4 ½" x 2 ½" electrical box. ELECTRICAL CONTRACTOR SHALL PROVIDE AND INSTALL: All conduits complete with wire from power source to control processor, from control processor to relay panels, from relay panels to PHYSICAL EDUCATION EQUIPMENT

27 CCA 1422 NEW S.T.E.M. BUILDING 2017 devices and from control processor to touch screen and one 4 ½" x 4 ½" x 2 ½" electrical box for mounting touch screen. 8. Safety Strap: Main Gym (Provide 2) Safety Strap is to be equal to DRAPER model no Aut-O-Loc 2 safety strap by Draper, Inc., Spiceland, IN. Aut-O-Loc 2 Safety Strap is designed to engage instantly whenever a cable or other lifting mechanism fails. Aut-O-Loc 2 is actuated by speed or inertia in order to stop a load from falling due to a sudden failure such as a cable breakage, cable clamp failure or any increase in speed due to failure or back drive of a winch. Aut-O-Loc 2 is rated for a 1000 lb (454 Kg) load and incorporates a 2 wide polyester belt with a breaking strength rating of 6000 lbs (2,721 Kg) to withstand a 1750 lb (794 Kg) free falling load without any failure of components or the belt. The housing and drum are manufactured from high tensile heat treated aluminum alloy that naturally resists corrosion without paint. The drum which houses the mechanism is a singular machined piece to retain its structural integrity in the case of a load capture. The locking mechanism always remains in the ready position regardless of whether belt is retracting or extending. The unit operates at a sound level less than 20db to allow the operator clearly hear the operational sounds of the winch and backstop, so they may stop winch operation if there are abnormal audible warnings to indicate possible mechanical issues. Aut-O-Loc 2 has a universal mount that can accommodate 3 ½ (89 mm) or 4 tube (102 mm) and can mount to support tubes running parallel and/or perpendicular to the backboard. Unit is self aligning with the use of two integral guide wheels so the force of a fall positions the unit in the ideal plane to prevent damage to unit and the supporting structure. The locking mechanism will fully engage within 3 (76 mm) of belt travel in the event of failure. The locking mechanism utilizes multiple high strength steel pawls that deploy and evenly load the drum and housing when engaged and do not rely on a singular locking mechanism. Aut-O-Loc 2 s retractable nylon strap includes a brightly colored warning strip that indicates when maximum payout of the belt has been reached. The strap also features a brightly colored warning indicator that deploys automatically when engaged. Aut-O-Loc 2 is permanently locked when a load of more than 1000 lbs (454 Kg) of force is captured and will not be functional after it has caught a significant load to prevent possible re-use and failure of critical components that are stressed when the unit engages a load. 2.4 WALL PADDING A. Main Gym Wall padding shall be equal to DRAPER Model ECOVISION FIRE RATED WALL PADS, by Draper, Inc. of Spiceland, IN. To be installed on North, South and West Walls Wall pads to be standard sized 2' x 6' and custom sizes as indicated on project plans. Panels shall consist of 7/16" thick urea-formaldehyde free oriented strand board (OSB) backer and 2" thick flexible open cell neoprene fire resistant cushioning material bonded together, then fully wrapped with flexible PVC and scrim laminate that features a leather grain emboss pattern. Cover shall have average weight of 14 oz. per square yard, breaking strength of 350 PSI, tear resistance of 65 pounds and be rated as self-extinguishing in accordance with California State Fire Code F- 230 and Class-A Rated in accordance with requirements of NFPA-101. Cover to be resistant to rot, PHYSICAL EDUCATION EQUIPMENT

28 CCA 1422 NEW S.T.E.M. BUILDING 2017 mildew, fungus and ultraviolet light and is available in Red, Dark Blue, Marine Blue, Beige, Grey, Black, Forest Green, Kelly Green, Brown, Maroon, Orange, Yellow, White, Purple and Navy Blue. Panel front and edges shall be fully wrapped and securely stapled to the OSB backer so that the backer is not exposed on front or four sides. Pads shall be supplied with concealed z-clip attachment at top and 1" fabric wrapped mounting flanges at panel bottom. The General Contractor is responsible to provide a flat surface to mount the wall pads on an uneven/divided surfaces and to box out all columns, exposed X-Bracing for proper installation as required by the manufacturer. Entire wall pad assembly shall have been submitted to indoor air quality evaluation (IAQ) using a GREENGUARD product evaluation protocol following the requirements of The GREENGUARD Environmental Institutes (GEI) Product Certification Program, ASTM Standard D5116 and the United States Environmental Protection Agency and modeled based on GEI requirements for a standard gymnasium loading and ASHRAE ventilation conditions. Pad assembly shall qualify as low emitting and found to met all of the requirements of the GREENGUARD for Children and Schools and GREENGUARD certification program which are emissions of total volatile organic compounds = 0.22 mg/m3, formaldehyde = ppm, total aldehydes = ppm, individual volatile organic compounds = 1/1000 TLV and = ½ chronic REL and total phthalates = 0.01 mg/m3. Entire pad assembly has been tested and meets the requirements of NFPA 101 Life Safety Code for class A rating (flame spread 0-25 and smoke development 0-450) when tested in accordance with ASTM E-84 (also published as NFPA-255, ANSI 2.5, UBC 8-1 (42-1) and UL 723). Entire pad assembly has been tested and meets the criteria set forth in the 2003 IBC section when tested in accordance with NFPA 286. NFPA 286 does not publish pass/fail criteria Pads shall meet all requirements of ASTM F Manufacturer must be able to provide independent lab and test reports to verify compliance with above standards and certifications. Provide cut outs for all wall mounted electrical/data wall plates. Coordinate with electrical drawings and verify exact locations in field prior to fabrication. 2.5 VOLLEYBALL EQUIPMENT A. Main Gym 1. Elite Volleyball System (1 required). Volleyball System shall be equal to DRAPER Model EVS-01 Elite Volleyball System by Draper, Inc. of Spiceland, IN. The EVS-01 shall consist of one standard with power winch and one standard with adjustable cable anchor collar. Post shall be telescoping type to meet all FIVB, USVBA, NCAA and NFSHSA requirements for competition. Post shall allow infinite height adjustment from 6' (1.854 m) to 8'4" (2.540 cm) to meet all age group height settings from elementary school use to international competition for both men and women. EVS-01 shall incorporate an internal spring assist mechanism for easy, precise and infinite height adjustments. EVS easily locks in place with a pressure lock hand knob and post is clearly marked at normal competition heights. The 6' (1.890 cm) bottom upright shall be 3½" O.D. (8.890 cm) schedule 80 aluminum tube, with a wall thickness of.300" (.7620 cm). The bottom upright is provided with a special rubber foot to protect finished floors and to provide precise net height adjustment. The upper telescoping adjustable tube shall be 2-7/8" OD (7.303 cm) schedule 80 aluminum tube, with a wall thickness of.276" (.7010 cm) with a 4" (10.16 cm) diameter pulley and oilite bushing. Both post sections have a clear annodized finish. PHYSICAL EDUCATION EQUIPMENT

29 CCA 1422 NEW S.T.E.M. BUILDING 2017 The tensioning winch shall incorporate a heavy-duty, self-locking worm gear mechanism. Winch shall be furnished with a heavy 2" (5 cm) wide high tensile nylon strap with heavy-duty snap hook to eliminate the possibility of hook breaking and guarantee safe connection to net top cable. The power winch is furnished complete with a folding handle for player safety. Systems shall come complete with DRAPER Model Power Volleyball Net by Draper, Inc. of Spiceland, IN. Net shall be 32' (9.75 M) long x 39-3/8" (1 M) high. Netting shall be high quality 4" square #36 black nylon cord with vinyl coated polyester hem double stitched around entire perimeter of net. Top hem of net shall be furnished with a 42'6" long x 1/8" diameter 2000 lb. minimum breaking strength galvanized aircraft cable with a nylon coating (3/16" OD) to protect against fraying. Ends of cable to have loops with heavy swaged type fittings for easy installation. Hems in end of net shall be furnished with a pocket for use with a 1/2" diameter fiberglass dowel rod. Ends of net shall have six 1" wide polypropylene tension straps with buckles for providing additional tightening of net. Bottom of net shall be furnished with a 1/4" diameter braided white nylon rope equipped with a spring loaded, pressure type rope tensioner. System also to include Draper Model Rope Tensioner and DRAPER Model Combination Antenna and Boundary Marker. 3. Floor Plate, Chrome-plated for existing floors (2 required). Volleyball Cover Plate shall be equal to DRAPER model Chrome plated cover plate by Draper, Inc. of Spiceland, IN. Chrome plated cover plate assembly shall be provided for use in either synthetic or wood floors. Chrome plated cover plate assembly may be used with new or existing floors. Cover shall consist of a steel outer ring with an outside diameter of 8" and in inside diameter of 4-1/8". Cover shall be equipped with swivel type retaining screw to prevent theft. A special key shall be provided for opening cover. Six #10 x 1-1/2" fl at head wood screws shall be provided to securely mount cover assembly to floor. Plate shall be installed flat to surface with no obstructions. 4. Floor Sleeve (One per cover plate required). Floor Sleeves shall be equal to DRAPER Model /2" I.D. Floor Sleeve by Draper, Inc. of Spiceland, IN. Floor sleeve shall be constructed of steel mechanical tubing with an inside diameter of 3-1/2", welded to a 4" x 4" bottom plate. Sleeve shall be 8-1/2" long and designed to be installed with the bottom at 9 ½" below the playing surface. 5. Transporter (1 required). Heavy-Duty Volleyball Post Transporter/Storage Cart shall be equal to DRAPER model transporter/storage cart by Draper, Inc., Spiceland, IN Heavy-duty transporter/storage cart shall be capable of storing and transporting one referee stand and six volleyball posts. Transporter/Storage Cart is provided with blue vinyl covered bottom shelf and pouch to allow for storage of nets, pads antennas and boundary markers. Frame shall be rectangular steel tubing finished with attractive gloss black powder coat. Transporter/Storage Cart rolls 4" x 1 1/4" non-marking swivel casters. 6. Judge's Stand (1 required). Judges stand shall be equal to DRAPER Model 5013xx (xx=color) by Draper, Inc. of Spiceland, IN. PHYSICAL EDUCATION EQUIPMENT

30 CCA 1422 NEW S.T.E.M. BUILDING 2017 Judges stand shall be designed to attach to a collar by means of a removable, self-locking pin. Collar slides over 3½" O.D. volleyball standard and is rigidly positioned to post with allen-head set screws. Frame shall be constructed of 1-1/2"x1-1/2", 14-gauge square steel tubing and 1" OD steel tubing, welded together. Legs, steps, platform, and handrails shall all be one solid unit. Judges platform shall consist of 1/2" thick, polyurethane finished Birch plywood, permanently bolted to stand. Handrail/ladder section shall be spaced vertically 16" on center with three (3) ladder steps spaced horizontally of 16" centers. Lower end of ladder tubes shall have 1/2" thick rubber bumper to protect finished floors. Ladder legs shall have 2" O.D. rubber wheels for easy transporting of stand. All metal components of stand shall be finished in black powder coat. Judges stand shall be supplied complete with safety padding for player protection. Upper section of stand shall have a snapped into place 1/12" polyethylene foam padding. Lower ladder tubes shall have removable, hook and loop attached pads of 1" neoprene foam. All pads shall be wrapped with 14 oz., polyester reinforced, dark blue vinyl (optional vinyl colors also available). Last two digits indicate pad color. Colors available: 01 White; 02 Marine Blue; 03 Brown; 04 Red; 05 Beige; 06 Orange; 07 Yellow; 08 Grey; 09 Maroon; 10 Dark Blue (standard); 11 Black; 12 Purple; 13 Forest Green. 7. Protective Pads for Standards (2 required). Volleyball Post Padding shall be equal to DRAPER Model 5011XX Official Padding for 3-1/2" O.D. Volleyball Systems by Draper, Inc. of Spiceland, IN. Pads shall be hinged at corners to fold neatly around posts and tensioning winch to provide maximum player protection. Pads shall be constructed of 11/2" thick polyethylene foam filler covered with polyester reinforced vinyl with three (3) hook and loop fastening straps for quick set-up and take-down, and shall be constructed to accommodate winch, or judges stand when used. Standard pads are Dark Blue in color unless otherwise specified. Last two digits indicate pad color. Colors available: 01 White; 02 Marine Blue; 03 Brown; 04 Red; 05 Beige; 06 Orange; 07 Yellow; 08 Grey; 09 Maroon; 10 Dark Blue (standard); 11 Black; 12 Purple; 13 Forest Green. 2.6 SCOREBOARDS- Main Gym (1) A. SCOREBOARD Shall be equal to Fair-Play Model BB-1600 wireless or approved equal to this specification by the architect. Provide 1 unit of this model. Overall cabinet size shall be 5 feet in height by 9 feet in length by 4 inches in depth including mounting brackets and constructed of aluminum. Cabinet color shall be as selected from manufacturer s standard colors with selected appropriate trim colors. Cabinet to be shipped assembled and constructed for wall mounting. Approximate weight shall be 127 lbs. Display digits shall be incandescent seven-segment bar type protected by a polycarbonate numeral front. Display digits shall be colored amber for game clock and red and green for other information. Color shall be determined by the color of the polycarbonate digit cover. All lamps shall be a low voltage clear bulb type. Digit height to be 12 inches for game clock and team scores and 10 inches for other display information. Game clock shall have a display capacity up to 99:59, team score to 199, period to 9, team fouls to 99, personal fouls to 9, player number to 99. Bonus or Double Bonus shall be indicated by two arrows for each team. Captions shall be adhesive backed white vinyl permanently attached to the cabinet as follows: Home and Visitor 6 inches high; Bonus, Period, Fouls and Player 4 inches high and Possession 3 inches high. Changeable captions for basketball, volleyball and wrestling shall be the same vinyl on aluminum plaques and shall be 4 high. Electronics to be packaged in a low voltage, plug-in PHYSICAL EDUCATION EQUIPMENT

31 CCA 1422 NEW S.T.E.M. BUILDING 2017 processor. Power to be 984 watts maximum 120 VAC, 60 Hz. Provide a #350 electronic horn rated at 10 0.Wireless or Approved Equal. B. CONTROL Shall be equal to model MP-70 with padded carrying case. Requires 120 VAC power source and draws 12 watts. Construction shall be an aluminum case 12 ¾ inches long by 2 ¼ inches high by 8 inches deep with 4 rubber slide-resistant feet. Operating features shall include a two-line LCD readout showing information as sent to the scoreboard display as well as constant display of time remaining or time lapsed; a changeable color coded keypad to allow key identification change by sport, numeric key pad, plus and minus keys for quick sequential data entry, a push-type horn button and a positive action rocker switch for the Time In and Time Out function. Electronic features shall include a program mode allowing change in sport controlled or accommodation of a sport rules change, a memory circuit to retain information if power interrupted and electronic foul memory. Provide Wireless and internal battery option. C. LIMITED WARRANTY Fair-Play provides a limited warranty for a period of five (5) years from the date of invoice against defects in workmanship or material. Defective components will be repaired or replaced on a factory exchange basis. Exclusions include, but are not limited to accident, neglect, abuse, misuse or natural disaster. Details available on request. PART 3 EXECUTION 3. 1 PREPARATION A. Coordinate support of basketball backstops and gymnasium divider curtains with roof structure to ensure proper distribution of loads and adequacy of attachment points. Ensure that building structure has been designed for loads of specific gymnasium divider to be provided. The backstops or curtains will not be allowed to attach to the building Purlins. Backstop Manufacturers are required to span all the rigid frames with 4 Tube Truss/Bridge Truss for attachment of the backstops and the curtain. All overhead Support Tube/Pipe to be 4 OD steel. 3 ½ Tube/Pipe will not be accepted. All Cradling is the responsibility of the manufacturer. The General Contractor is responsible to provide open access to the end walls (or any other structural steel) to allow the backstop manufacturer to attach spanning Tube Truss/Pipe to the rigid frames of the building. The General Contractor will be responsible for any finishes around and at these attachment locations. B. Coordinate configuration, size, and installation of basketball backstops and gymnasium divider curtains with height, slope, and type of building structure and lighting fixtures, mechanical equipment, ductwork, fire-suppression system, bleachers, athletic equipment, and other potential obstructions. C. Field-verify dimensions prior to fabrication. D. Coordinate electrical requirements for motorized operating mechanism to ensure proper power source, conduit, wiring, and boxes for keyed switches. Prior to installation, verify type and location of power supply. See Electrical Contractor Shall Provide and Install E. Coordinate delivery of Volleyball Floor Sleeves and Covers with sub-contractors responsible for installation. F. For installations made after wood gymnasium flooring is installed, provide protection and exercise care not to damage flooring INSTALLATION A. Install in accordance with manufacturer's written instructions and shop drawings. B. Install even, plumb and level. PHYSICAL EDUCATION EQUIPMENT

32 CCA 1422 NEW S.T.E.M. BUILDING 2017 C. Install control switch such that operator has view of complete basketball backstop during lowering and raising. D. Adjust limit switches of electric winch to ensure accurate position in both stored and lowered positions TESTING AND DEMONSTRATION A. Operate basketball backstops to ensure proper lifting and lowering. Adjust as required to ensure smooth operation and accurate positioning. B. Demonstrate to Owner's designated representative complete operation and required maintenance. END OF SECTION PHYSICAL EDUCATION EQUIPMENT

33 Project: NEW S.T.E.M. BUILDING MAIN CAFETERIA & TEACHERS ROOM 45 REINHARDT ROAD WAYNE, NJ Preferred Supplier: BFA Foodservice Equipment Alex Nasarow 325 Division St Boonton, NJ (973) (Contact) (973) (Fax) Item Qty Description EQUIPMENT LISTED FOR MAIN CAFETERIA ITEMS LISTED AS "FUTURE" ARE N.I.C. EQUIPMENT FOR TEACHERS ROOM EQUIPMENT FOR DINING ROOM 74 2 ea HAND SINK Advance Tabco Model No. 7 PS 65 Hand Sink, wall model, 14" wide x 10" front to back x 5" deep bowl, 304 series stainless steel, deck mounted fixed faucet, deck mounted soap dispenser, undermount towel dispenser, stainless steel construction, wall bracket, NSF, ccsaus 2 ea K 316 LUHA Wrist Handles Only, for splash or deck mount hand sink faucet (1 pair hot & cold 4" long blades), fits faucets supplied after November 2015 with hot & cold color rings that do not have exposed screw head 2 ea 7 PS 17B Welded Side Splash, 7 3/4" tall, both sides, for hand sinks with 10" x 14" bowl & deck mounted faucets 75 2 ea REACH IN REFRIGERATOR Everest Refrigeration Model No. EBR2D Deep Reach In Refrigerator, two section, 53 cu. ft. capacity, (6) shelves, bottom mounted refrigeration system, digital control system, adjustable self closing & field reversible doors, door locks, pressure relief port, stainless steel interior & exterior, (4) 4" diameter (5" overall height) swivel casters (front with brakes), incandescent interior lighting, 115v/60/1, NEMA 5 15P, 1/3+ HP, 4.92 amps, ETL Sanitation, ETL Safety 2 ea Parts and labor: Total 3 years from installation date (there is no more additional 6 months warranty this time) 2 ea Compressor: Total 5 years from installation date

34 Item Qty Description 76 2 ea HEATED CABINET, MOBILE Metro Model No. C539 HLFC U C5 3 Series Heated Holding Cabinet, lower wattage, with Red Insulation Armour, mobile, full height, insulated, clear polycarbonate door, removable bottom mount control module, thermostat to 200ºF, universal wire slides on 3" centers, adjustable on 1 1/2" increments (18) 18" x 26" or (34) 12" x 20" x 2 1/2" pan capacity, 5" casters (2 with brakes), aluminum, 120v/60/1 ph, 1440 watts, 12 amps, NEMA 5 15P, UL, CUL, NSF 77 2 ea HOT FOOD SERVING COUNTER Vollrath Model No Signature Server Stainless Steel Countertop with Hot Food Station, 88"W x 28"D x 34"H, modular, (6) 11 7/8" x 19 7/8" x 6 3/8" deep hot food wells, individual Touch Temp programmable control for each well, manifold drains included, 18 Ga/300 series stainless steel top & hot wells, 18/400 series stainless steel enclosed base clad with black laminate, stainless steel unibody construction, 4" heavy duty swivel casters with brakes, 8' cord & plug, 3750 watts, culus, NSF 4 2 ea 120/208v/60/1 ph 2 ea Laminate or Woodgrain finish for 88" base with stainless steel corner & edge protectors (choose from WilsonArt, Formica, Nevamar & standard finishes **contact factory for specialty laminate request**) 2 ea N98628 NSF2 (2011) Contemporary Breath Guard, cafeteria with top shelf, 3/8" thick tempered glass with polished ends, 1" stainless steel tubular construction, tempered glass end panels, for use with Vollrath (6) well Signature Server with stainless steel countertops, mounts to stainless steel solid surface (note: requires 14 gauge stainless steel solid surface), 1 year warranty, Made in USA (contact Vollrath for dimensions) 2 ea Upgrade to 14 gauge stainless steel work surface for, (6) well 88" Signature Server Hot Food Base 2 ea 30 Black 80% gloss 2 ea NO LIGHT OR HEAT No lights or heating, standard, no charge 2 ea O Operator Side Cutting board, 88", poly, overall width 8" 2 ea C Tray Slide, for customer side, 88"W x 12"D, 14 gauge, V rib, for Signature Server with stainless steel countertops, ADA 2 ea Storage Bag In Box, Stainless, fits Signature Server 88" Beverage Counter & Utility Stations, reinforced shelf, interior of base is unfinished, for 34" height units only 2 ea Work surface flange modified with line up locks, Keyhole slots on diagonal corners with stainless slide attached to side of base 2 ea Stainless steel skirting for 88" base 2 ea Filler Panels, 34"H, to fill the space between base cabinets 2 ea MODCOR TRIANGULAR CORNER AT END ea COLD PAN SERVING COUNTER

35 Item Qty Description Vollrath Model No Signature Server with Stainless Steel Countertops, NSF7 Cold Station, 88", refrigerated, 34"H, 9 5/8 O/A depth, Bloomington style recessed well places pans 3" below work surface, coils surround sidewalls, accommodates 6" deep pans, polyurethane foam insulation, standard well drains, seamless pan well opening 19 7/8" x75 3/4" x6 5/8" deep, 1/2 hp compressor, 120v/60/1 ph, 4.9 amps, NEMA 5 20P, UL, NSF, Made in USA 2 ea 120v/60/1 ph 2 ea COMPRESSOR SWITCH ON WORK SIDE. 2 ea Laminate or Woodgrain finish for 88" base with stainless steel corner & edge protectors (choose from WilsonArt, Formica, Nevamar & standard finishes **contact factory for specialty laminate request**) 2 ea N98628 NSF2 (2011) Contemporary Breath Guard, cafeteria with top shelf, 3/8" thick tempered glass with polished ends, 1" stainless steel tubular construction, tempered glass end panels, for use with Vollrath (6) well Signature Server with stainless steel countertops, mounts to stainless steel solid surface (note: requires 14 gauge stainless steel solid surface), 1 year warranty, Made in USA (contact Vollrath for dimensions) 2 ea Upgrade to 14 gauge stainless steel work surface for, 88" Signature Server Cold Pan (required for this breath guard) 2 ea 30 Black 80% gloss 2 ea NO LIGHT OR HEAT No lights or heating, standard, no charge 2 ea O Operator Side Cutting board, 88", poly, overall width 8" 2 ea C Tray Slide, for customer side, 88"W x 12"D, 14 gauge, V rib, for Signature Server with stainless steel countertops, ADA 2 ea Work surface flange modified with line up locks, Keyhole slots on diagonal corners with stainless slide attached to side of base 2 ea Stainless steel skirting for 88" base 2 ea Filler Panels, 34"H, to fill the space between base cabinets 2 ea MODCOR TRIANGULAR CORNER AT END ea REFRIGERATED SELF SERVICE CASE Structural Concepts Model No. CO67R Oasis Self Service Refrigerated Case, 71 1/4"W, 79 3/4"H, Breeze E (Type II) with EnergyWise self contained refrigeration system, Blue Fin coated coil, (4) non lit adjustable metal shelves, top light, one piece formed ABS plastic tub, black interior, (2) full end panels, 4"D removable wall spacer brackets, casters, cetlus, ETL Sanitation 2 ea NOTE: If GFCI is required, a GFCI breaker MUST be used in lieu of a GFCI receptacle 2 ea NOTE: 34" Minimum entry door clearance required (with out shipping skid & with rear spacer bracket removed) 2 ea 1 yr. parts & labor warranty, 5 yr. compressor warranty, standard 2 ea Breeze E (Type II) with EnergyWise refrigeration NSF Type II compliant, standard 2 ea v/60/1ph, 16.0 amps, 2 wire plus ground required, cord with NEMA 6 20P 2 ea 6 ft cord, exit at base, standard

36 Item Qty Description 2 ea NOTE: Compressor air intake from front & out rear, unit MUST remain 4" from wall & front panel cannot be blocked (Not applicable with remote refrigeration option) 2 ea CLEAN SWEEP Clean Sweep, automatic condenser coil cleaner 2 ea Base Support: Casters, with levelers, standard 2 ea Exterior: Wilsonart or Formica NON PREMIUM laminate (Color chart available from factory rep or access color selections via or 2 ea NOTE: SCC will not be responsible for additional charges incurred for Premium or other Manufacturer's laminate selections not originally quoted 2 ea Lower front panel: Black, standard 2 ea Left end panel: Cutaway with insulated glass, vinyl edging 2 ea Right end panel: Cutaway with insulated glass, vinyl edging 2 ea Back Panel: Solid back panel, black, painted, standard 2 ea Add Lights (LED 3500K) to standard shelves (4) 2 ea Roll down security cover, locking(requires two end panels (full or cutaway) per case) but CANNOT be used with Case to Case acrylic end panel)(must be chosen when case is ordered) 81 3 ea UTILITY SERVING COUNTER Vollrath Model No Signature Server Utility Station with Stainless Steel Countertop, 46"W x 28"D x 34"H, modular, 16/300 series stainless steel top, 18/400 series stainless steel enclosed base clad with black laminate, reinforced stainless steel unibody construction, 4" heavy duty swivel casters with brakes, culus, NSF 3 ea Matte Laminate Finish for Signature Server with Stainless Steel Countertops Corner Station & 46" Units with stainless steel corner & edge protectors (choose from WilsonArt, Formica, Nevamar & standard finishes **contact factory for specialty laminate request**) 3 ea No breath guard 3 ea Upgrade to 14 gauge stainless steel work surface for, 46" Signature Server Utility Station 3 ea C Tray Slide, for customer side, 46"W x 12"D, 14 gauge, V rib, for Signature Server with stainless steel countertops, ADA 3 ea Storage Bag In A Box Shelf, Stainless, fits Signature Server with Stainless Steel Countertops, 46" Beverage Counter & Utility Stations & Signature Server with Laminate or Corian Countertops, 48" Hot Well, 48" Bain Marie Hot Well, 48" NSF7 Cold Pan, 48" Refrigerated Cold Pan, 48" Non Refrigerated Cold Pan, 48" Utility, 48" Beverage Counter, reinforced shelf, interior of base is unfinished, for 34"H units only 3 ea Work surface flange modified with line up locks, Keyhole slots on diagonal corners with stainless slide attached to side of base 3 ea Stainless steel skirting for 46" base 3 ea Filler Panels, 34"H, to fill the space between base cabinets 82 4 ea CASH REGISTER STAND

37 Item Qty Description Vollrath Model No Signature Server with Stainless Steel Countertops, 34" high ADA Cashier Station, 28" long, 28"W, modular, without cashier drawer, operator side open with stainless steel floor, NSF 4 ea Matte Laminate finish for Signature Server with Stainless Steel Countertops Cashier Station with stainless steel corner & edge protectors (choose from WilsonArt, Formica, Nevamar & standard finishes **contact factory for specialty laminate request**) 4 ea Upgrade to 14 gauge stainless steel work surface for, Signature Server Cashier Station 4 ea C Tray Slide, for customer side, 28"W x 12"D, V rib, lift off bracket, for Signature Server with stainless steel countertops, ADA 4 ea Signature Server Cash Drawer, locking, drawer bell, steel construction, black powder coated finish, includes: ABS plastic removable money tray, with (5) coins & (5) bills capacity, stainless steel bill clips/hold downs, aluminum coin breaking plate 83 SPARE NO. 84 SPARE NO ea POS SYSTEM Custom Model No. POS SYSTEM POS SYSTEM N.I.C ea CROWD CONTROL STANCHION (PORTABLE) Winco Model No. CGS 38K Packed 2 ea Crowd Guidance System, 6 1/2' retractable belt, heavyweight, black 87 1 ea CABINET Custom Model No. CAB Storage cabinet for cafeteria supplies. Size: 60"x24" x 72" high with locking hinged doors,adj. interior SS shelving,unit in 6" legs with SS kick plate. 88 SPARE NO ea WIRE SHELVING UNIT Metro Model No. N356C Super Erecta Starter Shelving Unit, 48"W x 18"D x 63"H, (4) wire shelves, (4) posts, chrome plated finish, NSF 90 1 ea CASH REGISTER STAND Vollrath Model No Signature Server with Stainless Steel Countertops, 34" high ADA Cashier Station, 28" long, 28"W, modular, without cashier drawer, operator side open with stainless steel floor, NSF 1 ea STANDARD BLACK Black Laminate, standard, nc 1 ea C Tray Slide, for customer side, 28"W x 12"D, V rib, lift off bracket, for Signature Server with stainless steel countertops, ADA

38 Item Qty Description 1 ea Signature Server Cash Drawer, locking, drawer bell, steel construction, black powder coated finish, includes: ABS plastic removable money tray, with (5) coins & (5) bills capacity, stainless steel bill clips/hold downs, aluminum coin breaking plate 91 1 ea HOT FOOD SERVING COUNTER Vollrath Model No Signature Server Stainless Steel Countertop with Hot Food Station, 46"W x 28"D x 34"H, modular, (3) 11 7/8" x 19 7/8" x 6 3/8" deep hot food wells, individual Touch Temp programmable control for each well, manifold drains included, 18 Ga/300 series stainless steel top & hot wells, 18/400 series stainless steel enclosed base clad with black laminate, stainless steel unibody construction, 4" heavy duty swivel casters with brakes, 8' cord & plug, 1875 watts, culus, NSF 4 1 ea 120v/60/1 ph 1 ea STANDARD BLACK Black Laminate, standard, nc 1 ea N37311 NSF2 (2011) Single Deck Classic Cafeteria Breath Guard for 46" ADA Signature units (when ordered as replacement breath guard crating charges are applied) 1 ea Upgrade to 14 gauge stainless steel work surface for, (3) well 46" Signature Server Hot Food Base 1 ea NO LIGHT OR HEAT No lights or heating, standard, no charge 1 ea O Operator Side Plate Rest, with lift off bracket, ADA Signature Server with Stainless Steel Countertops, 46" 7" Overall Width 1 ea C Tray Slide, for customer side, 46"W x 12"D, V rib, lift off bracket, for Signature Server with stainless steel countertops, ADA 1 ea Storage Module with Sliding Doors, fits Signature Server with Stainless Steel Countertops, 46" Hot Well, 60" Cold Pan, 46" Utility Station, & 46" Beverage Counter & Signature Server with Laminate or Corian Countertops, 48" Hot Well, 48" Bain Marie Hot Well, 60" NSF7 Cold Pan, 62" Refrigerated Cold Pan, 48" Non Refrigerated Cold Pan, 48" Utility, 48" Beverage Counter, & 62" Frost Top, stainless steel, key lock for sliding doors, 24"W, opening height 16 1/2", depth 25 1/2" for 34"H units only 92 1 ea COLD PAN SERVING COUNTER Vollrath Model No Signature Server Stainless Steel Countertop with NSF7 Cold Station, self contained refrigeration, 60" Refrig., 34"H, 28" O/A depth, Bloomington style recessed well place pans 3" below work surface, coils surround sidewalls, accommodates 6" deep pans, polyurethane foam insulation, standard well drains, seamless display pan well opening 19 7/8" x 50 1/4" x 6 5/8" deep, 1/4 hp compressor, 4.9 amps, NEMA 5 20P, 120v/60/1 ph, UL NSF, Made in USA 1 ea 120v/60/1 ph 1 ea Compressor switch on work side. 1 ea STANDARD BLACK Black Laminate, standard, nc 1 ea double deck Classic Cafeteria Breath Guard for 60" ADA Signature units (when ordered as replacement breath guard crating charges are applied)

39 Item Qty Description 1 ea 1 ea 1 ea NO LIGHT OR HEAT No lights or heating, standard, no charge 120v/60/1 ph C Tray Slide, for customer side, 60"W x 12"D, V rib, lift off bracket, for Signature Server with stainless steel countertops, ADA 93 1 ea HAND SINK Advance Tabco Model No. 7 PS 65 Hand Sink, wall model, 14" wide x 10" front to back x 5" deep bowl, 304 series stainless steel, deck mounted fixed faucet, deck mounted soap dispenser, undermount towel dispenser, stainless steel construction, wall bracket, NSF, ccsaus 1 ea K 316 LUHA Wrist Handles Only, for splash or deck mount hand sink faucet (1 pair hot & cold 4" long blades), fits faucets supplied after November 2015 with hot & cold color rings that do not have exposed screw head 1 ea 7 PS 17B Welded Side Splash, 7 3/4" tall, both sides, for hand sinks with 10" x 14" bowl & deck mounted faucets 94 1 ea HEATED CABINET, MOBILE Metro Model No. C539 HLFC U C5 3 Series Heated Holding Cabinet, lower wattage, with Red Insulation Armour, mobile, full height, insulated, clear polycarbonate door, removable bottom mount control module, thermostat to 200ºF, universal wire slides on 3" centers, adjustable on 1 1/2" increments (18) 18" x 26" or (34) 12" x 20" x 2 1/2" pan capacity, 5" casters (2 with brakes), aluminum, 120v/60/1 ph, 1440 watts, 12 amps, NEMA 5 15P, UL, CUL, NSF 95 1 ea REACH IN REFRIGERATOR Everest Refrigeration Model No. EBR1D Deep Reach In Refrigerator, one section, 22 cu. ft. capacity, (3) shelves, bottom mounted refrigeration system, digital control system, adjustable self closing & field reversible door, door lock, pressure relief port, stainless steel interior & exterior, (4) 4" diameter (5" overall height) swivel casters (front with brakes), incandescent interior lighting, 115v/60/1, NEMA 5 15P, 1/4 HP, 4.10 amps, ETL Sanitation, ETL Safety 1 ea Parts and labor: Total 3 years from installation date (there is no more additional 6 months warranty this time) 1 ea Compressor: Total 5 years from installation date 1 ea Door hinged on left (NET) 96 SPARE NO. 97 SPARE NO ea VENDING MERCHANDISING Custom Model No. VENDING MACHINES UNITS BY SCHOOL 99 2 ea MERCHANDISING KIOSK

40 Item Qty Description Vollrath Model No Condiment Cart, 43"W x 28"D, all aluminum composite material (ACM) construction, base color in pre painted black, white or silver ACM with matching toe kick, indoor base with heavy duty casters, open storage (front), polyform countertop, includes (5) Vollrath 3 1/2 quart bain maries, 1" bumpers all sides (color to match base), Made in USA 2 ea Black 2 ea TWO Heavy Duty Locking Paddle Latch ACM Door, server side, (2 door max) 2 ea Raised Polyform Shelf 2 ea ACM Signage with Powder Coated Uprights 2 ea Base Color Option Laminate (one color) all sides 2 ea AMP Electrical Service ea TRASH RECEPTACLE, CABINET STYLE Plymold Model No SE Waste Receptacle Unit w/splash, single, 41 1/2"H, laminated swing door, heavy duty magnetic access door and continuous piano hinge, (1) 35 gallon rigid liner w/ high impact plastic casters, laminate finish, laminate edge top, black metal base 2 ea Laminate finish to be specified 2 ea Waste Receptacle Liner Only, rigid, 35 gallon, 19 1/2" x 19 1/2" x 29 1/2"H, w/ (3) 3" casters, plastic