ONE GOSS MODEL M-600 C WEB OFFSET PRINTING PRESS WITH 4 UNITS 1 WEB WITH ONE JF-55 FOLDER MASTER PRESS. Maximum web width

Transcription

1 GOSS MODEL M-600 C WEB OFFSET PRINTING PRESS WITH 4 UNITS 1 WEB WITH JF-55 FOLDER MASTER PRESS Cut-off length Maximum transfer area Maximum web width Maximum printing speed up to Maximum web speed 625 mm 618 x 960 mm 965 mm IPH * 9.55 m/s Power supply 400 Volts ± 10% 3 Phases + Earth 50 Hertz All the equipment connected to the main control must be designed for the above power supply Ancillary equipment in current contract and not manufactured by the SELLER is in accordance with specifications in force at the time of contract signature * Note : Maximal speeds are given for coated paper type LWC, MWC or equivalent ; speeds vary according to production characteristics (paper weight, fold type, ink coverage) and are specified in the charts or sketches of elements of the press (dryer, folder, sheeter, ) Actual production speed depends on elements unrelated with the inherent performances of the press (adequate environment, correct maintenance, crew skills, selection of consumables) See clause 9 (h) of General Sales Conditions (1) GOSS CONTIWEB horizontal splicer SH40-LI-1020 for two webs (9.7 m/s) The SH40-LI is a horizontal, zero speed splicer using mechanical shafts. The integrated infeed has a web guide. Standard equipment and features : Integrated electronically controlled infeed for constant web tension and infeed web up system including web guide. Remote infeed functions and web guide controlled through press control system

2 Automatic program for reel loading and unloading the expired reel (core) after the splice Central operating panel with paper and production data read-out on CRT display without storage Motorized reel side lay adjustment with indication on CRT display of splicer Automatic splicing at any reel diameter Festoon rollers with concave profile One web severer Three mechanical expanding reel shafts and one reel shaft trolley Remote diagnosis system through modem connection, customer to provide dedicated telephone line Technical data Metric Max. splicing speed 9.7 [m/s] Max. web width 1020 [mm] Max. reel diameter 1270 [mm] Max. reel weight 1600 [Kg] Web tension infeed [N] Web tension variation 1% from pre-set value + 5 [N] Standard core diameter 76 [mm] FOUR (4) GOSS Blanket to blanket printing units Extremely rigid construction with box type frame on the gear side and large dimensioned spacers In-line stacked cylinder arrangement. Cylinders are all mounted on special bearings providing maximum vibration absorption The units are driven by individual motors (one AC drive per unit) The plate cylinder can be automatically rotated to a fixed position to facilitate plate-up Chrome plated plate cylinders fitted with 40 mm wide hardened steel bearers. Plate cylinder undercut is 0.27 mm for a 0.30 mm aluminium plate and is equipped with a pneumatic plate lock-up device Plate cylinder positioning is controlled from the Omnicon console, allowing rapid plate change The four register adjustments consist of motorized lateral ( 2 mm), motorized circumferential ( 3 mm), motorized plate cocking ( 0.3 mm). Unit phasing register is obtained by unit drive synchronisation Each printing unit can be individually silenced Platforms between the units allowing plates to be mounted or removed easily, the web staying in the machine Inking : Large ink fountain with remote control of ink keys

3 The inking system can be converted from a to a split by means of a mechanical changeover of one roller Each inker can be silenced independently with or without the operation of the dampener system. The upper and lower print couples can be declutched independently of each other Inking is ensured by a total of 15 large diameter rollers Each inker includes : one ceramic ink fountain roller one nylon covered pick-up roller one nylon roller three nylon covered oscillating vibrators five rubber covered distributor rollers three rubber covered form rollers (two are self-oscillating) one rubber covered rider roller The vibrators are cooled by means of water circulation All form rollers follow plate cylinder skewing (form roll following) Two GOSS pneumatic ink scraping blades are provided per unit Dampening Convertible dampening system with sliding contact roller with pneumatic switching between the two modes of dampening (film or emulsification) from the main Omnicon console Each dampener includes : One rubber covered pan roller One chrome plated metering roller with special surface treatment and cocking adjustment One self-oscillating rubber dampener form roller One chrome plated jockey roller Each unit includes an integrated filtering assembly in the dampening water circuit The GOSS dampening system is designed for a high quality printing on coated or semi coated paper Other equipment A motor driven oil pump provides pressurized circulation as well as cascade lubrication of gears, unit clutches, oscillating mechanism, and all cylinder bearings. Oil cooling is provided through a heat exchanger and oil flow and temperature are monitored, indicated, and the press is stopped in the event of an oil flow failure

4 A motorized bypass web lead for systems with more than one web is provided. The web-up rolls under the units included are as follows : 5 units : bypass under the first unit after the infeed Platforms between units are hinged and pneumatically actuated Unit guarding is controlled by safety switches Ink piping along the printing unit gearside is provided for 4 colors. Hand valves are provided at each unit. Ink levelers are optional Bustle wheels are provided. Three wheels per unit are provided on all units, except the first unit in each unit group (i.e., on units 2, 3, 4, 5, and 6 on a six unit-one web press or units 2, 3, 4, and 6, 7, 8, of an 8 unittwo web press) Each unit is supplied with two blankets Set of web break detectors : GOSS web break detectors are interfaced with GOSS Omnicon system to provide first out indication and self-arming interlocks, and severer/web catcher interface with web break detectors GOSS web break detectors are installed at the exit of each unit, inside and after the chill roll section. (1) Space for printing unit installed at a later date This space is located after the splicer and includes two extra rollers and brackets in S-wrap configuration The electrical supply is upgraded for this future retrofit (1) Set of spare covered rolls for one half unit Includes covered rolls for dampening and inking system for one half unit EIGHT (8) Spare blanket(s) (1) Baldwin packing gauge (metric) (1) Autoplate device for four units The two plate cylinders of each unit are equipped with an automatic plate-up system including : One upper retractable rack for one new plate

5 One lower side movable rack for one new plate One pneumatically activated automatic tensioning system This system allows to change the plate without breaking the web The plate cylinders have no underpacking The maximum paper stock is 135 g/m 2 with 0.30 mm thickness plates and up to 200 g/m 2 with 0.35 mm thickness plates Autoplate mechanisms are designed to fullfil their functions only if handled in proper manner. They are not designed to withstand other constraints. Therefore it is obviously prohibited to load them with any extra weights Correct function of such a system is warranted only if cleanliness and maintenance are insured by the printer as per operator manual (1) Set of connecting parts for BALDWIN blanket cleaner integration for 4 units (1) BALDWIN automatic blanket cleaner model Impact for 4 units Electronically controlled wash-up procedure, with the possibility of preselecting ten different wash-up programs. Automatic advance of wash-up cloth Impact system uses pre-soaked tissue rolls Controlled from the unit Omnicon console Two wash-up bars per perfecting unit, placed on the infeed side of the unit Three Prepac impregnated wash cloth rolls are supplied with each washer (1) Circulator and temperature control for reduced Alcohol printing (<10 % alcohol) TECHNOTRANS Gamma.c 600 combination unit for dampening solution cooling and ink roller temperature control for 5 units Integrated in one cabinet. Water cooled chiller for dampening solution circuit and ink roller temperature control circuit for connection to a central chill water supply Dampening solution circuit : Stainless steel tank with integrated filter box One circulation and one feed pump Integrated additive mixer type aquados.d 5 Intermediate tank located near the last unit for return of the dampening solution from the press to the delta.c unit Conductivity display on the circulator cabinet Ink roller temperature control circuit :

6 The system works in closed loop circuit Electrical heating, for cold press start up Circulation pump Motor valves for temperature regulation of the return water coming back from the ink rollers (1) TECHNOTRANS ph value indication Display on the Tecon panel of the circulator cabinet (1) GOSS patented active web catcher This system is fired by a web break detection system and catches the web via an air knife and two catching rollers in case of web break in the dryer or after the dryer (linked to Ecocool detection) The system is installed between last printing unit and dryer The efficiency rate of the system is above 90% (1) GOSS CONTIWEB dryer with integrated afterburner and Chill roll section ECOCOOL /T for one web max. speed 10.7 m/s (2110 fpm) for 90 gsm (61 lbs) paperweight max. speed 8.6 m/s (1700 fpm) for 135 gsm (91 lbs) paperweight The Ecocool/T dryer is a web offset dryer with the functions of drying, chilling and guiding the web integrated in one single system In the dryer section (Ecotherm concept with integrated afterburner) the printed web will be dried at low air temperatures. The dryer makes direct use of the energy contained in the solvents in the system by means of active concentration control. In the thermal afterburners the solvents are burnt to produce hot clean air. The solvent concentration is controlled through constant temperature and pressure measurements, steering the frequency controlled fans. The result is a reduction of the gas consumption depending on ink coverage, paperweight and speed The Ecocool system includes small-diameter chill rolls positioned very close to the exit of the drying section. This allows better contact of the web to the chill rolls, which increases efficiency and eliminates solvent condensation The web guide on the first chill roll makes this excellent concept complete In the cooling zone the web temperature is reduced at the dryer outlet by approximately 40 o C (72 o F) During production stops the dryer is kept at Stand-By temperature for quick restart Standard equipment and construction features : The Ecocool dryer is supplied as one complete unit Comply with the latest standards EN 1539, NFPA 86 and the directives of the VDI Three temperature zones : heating zone, drying zone, cooling zone and a chill section

7 The air circulation system provides a high air volume to the patented "Crossjet" air nozzle bars Web temperature control by infrared camera, located between drying zone and cooling zone Two afterburner installations with heat exchangers and frequency controlled fans Door sensors for safety Nine small diameter chill rolls of which the fourth roll is driven by a frequency controlled AC motor Contiweb web guide system and web break detection Web tension measurement at the last roller Silicone applicator, before the first and the second chill roll, including reservoir and mixer, and including independent speed control of the silicone rollers One basic water piping system including valve, pump and filter Modem connection for remote diagnosis system, customer to provide dedicated telephone line Minimum dynamic gas pressure (note) : 100 mbar 1.45 psi Maximum static gas pressure : 330 mbar 4.8 psi Gas type different from natural gas on request The performance of the dryer is as diagram showing speed limitation according to paper weight and ink coverage (1) GOSS CONTIWEB Remoistening & Advanced Silicone package for one web The Remoistening & Advanced Silicone Package consists of : The controls on the Silicon Applicators The silicone applicator will be equipped with small mix tanks for each silicone roller. Silicone oil out of the reservoir with the concentrated silicone and water are mixed in these small tanks for each applicator. The amount of silicone oil coverage and water can be controlled separately for each side of the web. All components are integrated in the Ecocool Remoistening system The absolute moisture content in the product after remoistening can be as high as 4,5%. Normal moisture values are in the range of 3.5 %. Note: remoistening system is integrated in the silicone applicator and controls (1) GOSS CONTIWEB Webbing-up chain for Ecocool/T 93 for one web (1) GOSS Multiple combination folder model JF-55 for one web The basic JF-55 folder is a single width combination folder with one rotary chopper fold assembly featuring very high production speeds and a single stream delivery for magazine products and a single stream delivery for tabloid products. It can produce at speeds of up to iph and consists of the following features : Lower folder :

8 Forming rolls are provided at the former nose and are horizontally and vertically adjustable Two sets (upper and lower) of driven, 178 mm wide, air-loaded urethane pinch pulleys Circumferential perforator/scorer (in-line) mounted between the two sets of pinch pulleys and actuated via air cylinder. On-the-run depth and lateral adjustment is provided Cross perforator cylinders with on-the-run circumferential phasing and depth adjustment One part cutting cylinder with one knife box fitted with soft cheekwoods Three part transfer cylinder with three sets of active tucker blade assemblies, pins and cutting rubbers. On-the-run motorized fold lap adjustment is provided Three part jaw folding cylinder. Jaw segments are adjustable to accomodate various paper stock thicknesses One gear driven quarter folding assembly including a gear driven rotary blade and vacuum slowdown table. Chopper blade timing can be phased on-the-run delivery. The quarter fold assembly can be silenced by means of an electromagnetic clutch Two sets of fans (tabloid - chopper fold) Half-folded (tabloid) products deliver across quarter fold delivery table into fans which deposit the product on a mechanically driven creeping belt delivery The products, as per technical specifications, are delivered as follows : Spine leading, perpendicular to press center line, for tabloid products (and also double parallel and delta products, when option is selected) Spine leading, parallel to press center line, for quarter folded products Automatic product changeover, folder presetting and remote control integrated via Omnicon system, less than 2 minutes to change fold Circulating oil lubrication for main folder gears. Centralized automatic grease lubrication for all cylinder bearings and cylinder cam followers Including lighting inside the folder Platforming and stairways with handrails are provided to all operational points Ultrasonic jam detectors are provided Quarter fold delivery Signature delivery towards the splicer, spine leading

9 SPEEDS (SIGNATURES PER HOUR) AND ACCURACIES (mm) - JF-55 TABLOID Paper weight 1 x 4 p ½ web 1 x 8 p 1 web 1 x 16 p 2 webs g/m 2 (22-26 lbs) ± 0.3 / ± g/m 2 (27-37 lbs) ± 0.3 / ± 0.5 ± 0.3 / ± g/m 2 (38-48 lbs) ± 0.3 / ± 0.5 ± 0.4 / ± g/m 2 (49-60 lbs) ± 0.3 / ± 0.5 ± 0.4 / ± g/m 2 (61-77 lbs) ± 0.3 / ± 0.5 ± 0.4 / ± g/m 2 (78-91 lbs) ± 0.4 / ± 0.6 ± 0.4 / ± ± 0.3 / ± ± 0.4 / ± ± 0.4 / ± ± 0.5 / ± ± 0.5 / ± ± 0.5 / ± 0.7 Fold accuracy : Spine with first cross perforation - Spine without first cross perforation MAGAZINE Paper weight 1 x 8 p ½ web 1 x 16 p 1 web 1 x 16 p 2 webs g/m 2 (22-26 lbs) ± 0.4 / ± g/m 2 (27-37 lbs) ± 0.4 / ± 0.8 ± 0.3 / ± g/m 2 (38-48 lbs) ± 0.3 / ± 0.6 ± 0.4 / ± g/m 2 (49-60 lbs) ± 0.3 / ± 0.6 ± 0.4 / ± g/m 2 (61-77 lbs) ± 0.3 / ± 0.6 ± 0.4 / ± g/m 2 (78-91 lbs) ± 0.3 / ± 0.6 ± 0.4 / ± ± 0.4 / ± ± 0.4 / ± ± 0.4 / ± ± 0.4 / ± ± 0.4 / ± ± 0.5 / ± 0.8 Fold accuracy : Spine with linear perforation - Spine without linear perforation Important : These performances are those of a JF-55 folder equipped with Vacucontrol, chopper fold moistening system and fold perforations other than those specifically considered. The folder must be in good running conditions (correct settings, good mechanical conditions). Speed and accuracy are associated to coated paper, type LWC, MWC and equivalent. The web width must be in compliance with folder pin, gripper and tape positioning. Half of the total tolerance value is the standard deviation from the mean

10 FOLDER SPECIFICATIONS (JF-55) (mm) (inch) IMPRESSION LENGTH Folding Capacity 2 Webs Number of Ribbons (up to) 4 Maximum Web Width Ribbon centered on the former Ribbon on one side of the former Minimum Ribbon Width before slitting 1/3-2/ Minimum web Width centered to chopper fold Minimum ribbon Width over former side Lap Adjustment (all products) +/ /-.50 Maximum distance between pins and cut edge : 6.24 Stock Range 32 to 135 g/m² (22-91 lbs)*1 Max. Quarter Fold Thickness Max. Double Parallel Thickness Max. Tabloid Thickness Max. Delta Fold thickness Delivery Conveyor Shingle spacing (Fixed Speed) (quarter fold) (other products) 35 +/ / / /-.2 (1) Paper lead assembly with angle bars for two webs The paper lead includes : 1 Conversion from lbs to g/m²: 100 lbs = 148 g/m²

11 For each web : One chrome-plated driven pull roll, with four air-loaded trolleys. The ON/OFF function is controlled either on the angle bar module or from the console One scissor-type slitter to cut the web into two ribbons(1/3-2/3, 1/2-1/2 or 2/5-3/5). Slitter position is motorized Four full web width chrome plated angle bars with air hole adjustment to adapt to ribbon location and ribbon width (or full web for bay-window if option is selected) Two angle bars are motorized and controlled either on the angle bar module or from the Omnicon console. Their location is displayed on the console and can be stored for later presetting of similar jobs Two full web width motorized linear compensators with display of position on the console. The compensators are controlled by the auxiliary cut-off control system specified hereafter All compensator and angle bar screws are protected against dust with helicoïdal springs And also : One chrome plated driven pull roll (RTF) with central split hardened steel anvil for slitting or perforating, with four pneumatic trolleys and one slitter/perf. system provided Tall former drilled for low pressure air with carbide coated former nose. Motorized position adjustment is included Each pull roll is driven by its own motor Former nose towards sheeter (1) Paper lead assembly between two folders for one web The paper lead includes for the second folder : One chrome plated driven pull roll (RTF) with central split hardened steel anvil for slitting or perforating, with four pneumatic trolleys and one slitter/perf. system provided Tall former drilled for low pressure air with chrome plated former nose. Motorized position adjustment is included Former nose direction identical to the first folder (1) Double parallel and delta fold cylinder With triple cross perforation Set of extra jaws on the folding cylinder for delta products Two part delta and double parallel folding cylinder with two sets of grippers and two active tucking blade assemblies. Delta and double parallel products can be quarterfolded

12 All double parallel and delta signatures are delivered spine leading perpendicular to the press centerline SPEEDS (SIGNATURES PER HOUR) AND ACCURACIES (mm) - JF-55 DIGEST TWO-ON 2 x 8 p 2 x 16 p 2 x 32 p Paper weight ½ Web 1 Web 2 Webs g/m 2 (22-26 lbs) ± 0.4 / ± 0.6 ± 0.4 / ± g/m 2 (27-37 lbs) ± 0.4 / ± 0.6 ± 0.4 / ± 0.6 ± 0.5 / ± g/m 2 (38-48 lbs) ± 0.4 / ± 0.6 ± 0.5 / ± 0.7 ± 0.5 / ± g/m 2 (49-60 lbs) ± 0.4 / ± 0.6 ± 0.5 / ± 0.7 ± 0.5 / ± g/m 2 (61-77 lbs) ± 0.4 / ± 0.6 ± 0.5 / ± 0.8 ± 0.6 / ± g/m 2 (78-91 lbs) (1) ± 0.4 / ± 0.6 ± 0.5 / ± 0.8 ± 0.6 / ± 1.0 Fold accuracy : Spine with second cross perforation - Spine without second cross perforation (1) : g/m² only CHOPPED DELTA Paper weight 1 x 12 p ½ Web 1 x 24 p 1 Web g/m 2 (22-26 lbs) ± 0.6/ ± g/m 2 (27-37 lbs) ± 0.6 / ± 0.8 ± 0.6 / ± g/m 2 (38-48 lbs) ± 0.6 / ± 0.8 ± 0.6 / ± g/m 2 (49-60 lbs) ± 0.6 / ± 0.8 ± 0.6 / ± g/m 2 (61-77 lbs) ± 0.6 / ± 0.8 ± 0.6/ ± g/m 2 (78-91 lbs) ± 0.6 / ± 0.8 ± 0.6 / ± 1 Fold accuracy : Spine with second cross perforation - Spine without second cross perforation

13 (1) GMI automatic color register control system PrintQuick for one web 4/4 Color to color register control for both the circumferential and lateral axes. Controls up to 8 colors per web surface, by measuring a microtarget. A digital file of the microtarget is included. Register control measurements are made with a high speed CCD camera located after the final print unit and before the dryer. Register motors are controlled via the Omnicon console Camera lateral position can be preset from the Omnicon console (1) QUADTECH longitudinal cut-off control PPC3000X for one web or two ribbons This system, with its non motorized detecting photo-electric cells located near the web path rollers just before the former, automatically controls the servo-motors for the ribbon registers. The remote control is operated from a control panel located near the folder deliveries (1) GMI automatic Closed Loop Color control system, model ColorQuick for one web This system mainly consists of : 2 scanning spectrophotometers with motorized transport system assemblies 1 Press Computer module The spectrophotometers measure patches in a color bar, to be placed according to GMI specifications and control the density of each color through the Omnicolor control system of the press 1user Interface console for control of the Color Quick sytem and display The color bars are available as digital files in a format compatible with the CIP3 recommendations (1) GMI SPC Reporting (mandatory for first installation) Software for the creation of Statistical Process Control (SPC) reports For each job, histograms of density differences, dot gain, trends Nota: This option does not include a dedicated computer and a printer to be supplied by the purchaser Ethernet cable between press and computer to be supplied by the Purchaser (1) GOSS Color Control Interface The gateway provides the possibility to connect Close Loop Color density control to the ink key control of the press (1) Air blower and air cooler Including air cooler to supply low pressure air to the folder paper lead (1) PLANATOL OPIMATIC COMBIJET system 8DT (5 heads) Modular system for intermittent longitudinal gluing and softening, complete with remote control from the auxiliary console or from the

14 COMBIJET cabinet, also including mounting brackets, bars, hoses and wires Memory for 29 product pictures, each with individual glue patterns, which can be programmed by the operator Motorized lateral adjustment of the gluing and softening head location with path measuring and feedback Feeding of adhesive and fold-softening agent from pressurized tanks, with a volume of 50 kg each Contact application with resistant ceramic nozzles Remote diagnosis system as an option available (1) GOSS Modular main press drive system GOSS Modular Main Drive System is specially designed with SIEMENS for printing press controls and utilizes industry-accepted components All drives are built to a nominal 400 volts ± 10%, 3 phase, 50Hz standard (or 460 volts ± 10%, 3 phase, 60Hz). Values outside this range may cause equipment damage and/or incorrect press operations, invalidating the press warranty. Other power supplies can be accommodated through optional transformer The press system is provided with individual AC drive motors and controllers for each unit, each independant chill roll section, slitter roll, RTF and folder. Controls for individual and group operations are provided as a part of the Control System Drive cabinets are delivered tight together in large sub assembly. Each sub assembly is equipped with its own chilling equipment. Customer is responsible to supply chilled water as per pre-installation meeting and documents. Cabinets are sealed for dust free function (IP54) (1) Electrical power distribution cabinet This cabinet includes : One switchboard section, sized for the press system. It includes a main switch and individual breakers housed in an enclosure for the following press components : Main Drive system, units, chill, paper lead and folder, Splicer and auto roll loading (when supplied), Dryer, Press power distribution One press power distribution for auxiliaries and post press equipment - Auxiliary I/O and power distribution enclosure in a prewired enclosure. Interfaces for the dryer, alarms, auxiliary equipment and the grease pump are provided to the press I/O system

15 Note : Customer has to provide separate power supply for press lighting (units and folder) and for press plate preparation equipment Auxiliary equipments connected to the power distribution must comply with the Main Power Supply voltage. If not, a transformer may have to be added to the equipment (RFQ) (1) Communication enclosure (PLC) It includes all PC, PLC and network connection for the complete press system Is also included the UPS (Uninterrupted power supply) Note : Electrical and electronics equipments are designed for a press room temperature that should not exceed 45 C (113 F) at the cabinet location (1) NELA Pneumatic plate punch for Autoplate and non Autoplate, model HAP Designed to GOSS INTERNATIONAL specifications and manufactured by NELA Adapted for units with Autoplate (1) NELA Semi-automatic plate bender for Autoplate and non Autoplate, model HAO Designed to GOSS INTERNATIONAL specifications and manufactured by NELA Adapted for units with Autoplate (1) GOSS set of spare parts, List A (1) Tool box One set of tools, one set of flat spanners, one set of socket heads, screw drivers, portable lamp (1) Small empty console for cut-off control auxiliary equipment This console is located between the Omnicolor consoles and integrates control panels for the color register control (1) GOSS Omnicon Control system Press System operation combines functions from Omnicon Press Control and Color Control System from one Master Press Console per PRESS Omnicon Press Control System is PLC based for control of all print, fold and drive functions Features include :

16 Windows NT operating system Master drive system Pendant mounted touch screen monitor Pull out trays for keyboard and mouse Sequencing of print functions can be automatically or manually initiated Remote ink and water control with the added capability to track press speed Motorized circumferential and lateral register as well as plate cylinder skewing are adjusted via touch screen control Remote infeed tension adjustment with readout of dancer air cylinder loading, and push button control to allow for engaging or disengaging of the infeed nips Good and total counters for folder or sheeter Press operations and faults displayed through touch screen monitor Bar graph display for ink key values as well as on touch screen Multiple language support Modem capability for remote diagnostics of press system. Customer must supply a dedicate telephone line The Color Control System provides remote adjustment, presetting and monitoring of ink key position. Operator consoles incorporate a LED bargraph key position display. A system can consist of up to four consoles Features include : Each console can be configured independently of other consoles Each console can be configured to control up to eight units (16 inkers) Supports GROUP and ALL key moves 500 previously run jobs can be recorded and stored on each console Remote jobs storage capability with GOSS scanner or Prepress Gateway Remote ink/water roll speed control Remote register control (lateral, circumferential and plate cylinder skewing) Fixed top mounted on top of console to hold color OK sheets The press is equipped with : One Master Omnicon press control console including one color control One additional Omnicon press console for the units (1) Optional Omnicon console with color control (1) Prepress Interface (PPI) without Job Memory Card Drive (with Omnicolor consoles) Interface between digital pre-press systems and the printing press This system permits the conversion of the area coverage into area coverage values for the individual ink zones as well as set up of ink roller speed

17 Paper type and ink type are used to define the ink profile and the speed of the ink roller Data are transferred ON-LINE to the Omnicolor Master Console and provide precise values for pre-setting of ink keys. Preset values can be updated after the job is run and stored on the Omnicolor console for reprinting of job at a later time Includes the software and an operator manual All additional hardware (PC, cables and if needed hubs/routers) is to be supplied by customer, according to GOSS specifications The prepress interface software runs under Microsoft Windows 2000 The Prepress Interface accepts files only in CIP3 format (version 2.1) One Prepress Interface works with several presses installed in the same press hall (1) HARIG central chiller model KKS 100 (40 ) for 4 units for 1 web ( iph) Two chilled water circuits Equipment for complete press, consisting of : Water chill unit with an air cooled condenser for outside placement Wiring and piping between press and chiller and between chiller and condenser are not included

18 ANCILLARY EQUIPMENT APPROVED BY GOSS INTERNATIONAL MONTATAIRE AND ACQUIRED BY THE PURCHASER 1. Should the PURCHASER directly purchase any ancillary equipment to be used in conjunction with the GOSS press, a full description must be given below, in order to ensure that it is compatible with the machinery supplied by the SELLER. 2. The specifications and the precise supply limits and safety norms of all the items of ancillary equipment listed below must reach GOSS INTERNATIONAL MONTATAIRE no later than 4 weeks after the Sales Agreement is signed. Failure to meet this dead line could result in delayed shipment of the press. 3. In the case of any ancillary equipment purchased directly by the PURCHASER, all adjustments, and the expenses arising therefrom, and the necessary mechanical and electrical connecting parts shall be provided by the PURCHASER and at its expense. 4. In the case of any equipment acquired directly by the PURCHASER, the interfaces (including the cables, consoles, controls and platforms), the installation, commissioning and the guarantee obligations in respect of this equipment are excluded from the obligations of GOSS INTERNATIONAL MONTATAIRE. 5. The safety responsability for these equipments will be born by the PURCHASER. 6. List of equipment : None Equipment Quantity Manufacturer References ANCILLARY EQUIPMENT NOT APPROVED BY GOSS INTERNATIONAL MONTATAIRE AND ACQUIRED BY THE PURCHASER 1. It is standard procedure at GOSS INTERNATIONAL MONTATAIRE for the Research Department and the Product Department to approve all equipment used on a GOSS press, particularly where its use can affect the overall performance of the machine or the safety rules. Such approval has not been granted to the ancillary equipment listed below. 2. In the case of any ancillary equipment acquired directly by the PURCHASER, all adjustments and the necessary connecting parts shall be for the account of the PURCHASER. 3. In the case of any equipment acquired directly by the PURCHASER, the interfaces (including the cables, consoles, controls and platforms), the installation, commissioning and the guarantee obligations in respect of this equipment are excluded from the obligations of GOSS INTERNATIONAL MONTATAIRE. 4. It is clearly understood that GOSS INTERNATIONAL MONTATAIRE cannot be held liable for any damage or accidents which may result from the use or operation of this equipment. 5. Where a non-approved item of equipment is specified by the PURCHASER,GOSS INTERNATIONAL MONTATAIRE do not guarantee the overall performance of the press. 6. List of equipment : None Equipment Quantity Manufacturer References

19 ANCILLARY EQUIPMENT NOT APPROVED BY GOSS INTERNATIONAL MONTATAIRE AND SOLD WITH THE MACHINE 1. It is standard procedure at GOSS INTERNATIONAL MONTATAIRE for the Research Department and the Product Department to approve all equipment used on a GOSS press, particularly where its use can affect the overall performance of the machine or the safety rules. Such approval has not been granted to the ancillary equipment listed below. 2. Where a non-approved item of equipment is specified by the PURCHASER, GOSS INTERNATIONAL MONTATAIRE do not guarantee the overall performance of the press and any damage or accident which may result from the use or operation of this equipment. 3. List of equipment : None Equipment Quantity Manufacturer References SPECIFICATION OF PLATE PUNCH The MACHINERY is delivered with a plate punch and a plate bender in conformity with the drawing of standard GOSS plate. If the PURCHASER wants special perforations, the PURCHASER must provide one of the following pieces of information (mylar or standard plate used by the PURCHASER) in order to ensure that the plate bending and perforating system is properly compatible with the plating-up system on the plate cylinders. This information has to be returned to the SELLER no later than 4 months before the contractual shipment date. Should there be an error or delay in the specifications provided, the SELLER cannot be held responsible for the delay and additional cost incurred. CTP (Computer To Plate) COMPATIBILITY In order to check the positioning of plates by the CTP system is compatible with the SELLER's specifications (punching and bending), and to obtain the best results for the color register control and the plate cocking; the PURCHASER undertakes to provide the exact references of the CTP system used by the PURCHASER within 15 days after contract signature (filling in the specific CTP supplied document - see following pages). Based on this information, the SELLER shall confirm whether the CTP system is compatible and whether an optimum use of the insolation-punching-bending process is possible

20 CHECK LIST : COMPUTER TO PRESS DATE : Customer : Press n : Printing : Project of press : Type of press already installed in the customer plant... Computer to film : Manufacturer... Model... Dimensions maxi-mini of the films Check list Computer to plate : Manufacturer... Model Dimensions of the CTP punches... Dimensions maxi-mini of the plate. Drawing showing the position of the plate/film in the CTP : Drawing hereafter completed Compatibility with other presses : Yes No Plate drawing of other presses : Press inking pre-adjustment: 1). By the plate scanner : Yes No Supplier plate dimension maxi-mini Model 2). By direct connections to the press : Yes No Model

21 Mini Maxi Dimension Plate Film Running direction Dimension Mini Maxi Indicate on this drawing : Plate/film leading edge... Plate/film trailing edge... Dimension maxi-mini... Position : Of the mechanics stops with exact position Of the electronics stops...

22 GAS SPECIFICATION FOR DRYER The PURCHASER must specify the following information in order to ensure that the drying equipment included in the Agreement is compatible with the type of gas supplied. This specification sheet shall be completed and returned to the SELLER no later than 4 months before the contractual shipment date. Should there be an error or delay in the specifications given below, the SELLER cannot be held responsible for the delay and additional cost incurred. 1. Type of fuel : 2. Calorific value : 3. Gas pressure available in printing works : 4. Pressure to be delivered to dryer : 5. Chemical analysis of gas : N.B. : Depending on the type of gas, any additional cost shall be charged to the PURCHASER in case the specifications are given after the signature of the present Agreement.

23 Appendix A1 GOSS MODEL M-600 C WEB OFFSET PRINTING PRESS WITH 4 UNITS 1 WEB WITH JF-55 FOLDER SLAVE press Cut-off length Maximum transfer area Maximum web width Maximum printing speed up to Maximum web speed 625 mm 618 x 960 mm 965 mm IPH * 9.55 m/s Power supply 400 Volts ± 10% 3 Phases + Earth 50 Hertz All the equipment connected to the main control must be designed for the above power supply Ancillary equipment in current contract and not manufactured by the SELLER is in accordance with specifications in force at the time of contract signature * Note : Maximal speeds are given for coated paper type LWC, MWC or equivalent ; speeds vary according to production characteristics (paper weight, fold type, ink coverage) and are specified in the charts or sketches of elements of the press (dryer, folder, sheeter, ) Actual production speed depends on elements unrelated with the inherent performances of the press (adequat environment, correct maintenance, crew skills, selection of consumables) See clause 9 (h) of General Sales Conditions

24 FOUR (4) GOSS Blanket to blanket printing units Extremely rigid construction with box type frame on the gear side and large dimensioned spacers In-line stacked cylinder arrangement. Cylinders are all mounted on special bearings providing maximum vibration absorption The units are driven by individual motors (one AC drive per unit) The plate cylinder can be automatically rotated to a fixed position to facilitate plate-up Chrome plated plate cylinders fitted with 40 mm wide hardened steel bearers. Plate cylinder undercut is 0.27 mm for a 0.30 mm aluminium plate and is equipped with a pneumatic plate lock-up device Plate cylinder positioning is controlled from the Omnicon console, allowing rapid plate change The four register adjustments consist of motorized lateral ( 2 mm), motorized circumferential ( 3 mm), motorized plate cocking ( 0.3 mm). Unit phasing register is obtained by unit drive synchronisation Each printing unit can be individually silenced Platforms between the units allowing plates to be mounted or removed easily, the web staying in the machine Inking : Large ink fountain with remote control of ink keys The inking system can be converted from a to a split by means of a mechanical changeover of one roller Each inker can be silenced independently with or without the operation of the dampener system. The upper and lower print couples can be declutched independently of each other Inking is ensured by a total of 15 large diameter rollers Each inker includes : one ceramic ink fountain roller one nylon covered pick-up roller one nylon roller three nylon covered oscillating vibrators five rubber covered distributor rollers three rubber covered form rollers (two are self-oscillating) one rubber covered rider roller The vibrators are cooled by means of water circulation All form rollers follow plate cylinder skewing (form roll following)

25 Two GOSS pneumatic ink scraping blades are provided per unit Dampening Convertible dampening system with sliding contact roller with pneumatic switching between the two modes of dampening (film or emulsification) from the main Omnicon console Each dampener includes : One rubber covered pan roller One chrome plated metering roller with special surface treatment and cocking adjustment One self-oscillating rubber dampener form roller One chrome plated jockey roller Each unit includes an integrated filtering assembly in the dampening water circuit The GOSS dampening system is designed for a high quality printing on coated or semi coated paper Other equipment A motor driven oil pump provides pressurized circulation as well as cascade lubrication of gears, unit clutches, oscillating mechanism, and all cylinder bearings. Oil cooling is provided through a heat exchanger and oil flow and temperature are monitored, indicated, and the press is stopped in the event of an oil flow failure A motorized bypass web lead for systems with more than one web is provided. The web-up rolls under the units included are as follows : 5 units : bypass under the first unit after the infeed Platforms between units are hinged and pneumatically actuated Unit guarding is controlled by safety switches Ink piping along the printing unit gearside is provided for 4 colors. Hand valves are provided at each unit. Ink levelers are optional Bustle wheels are provided. Three wheels per unit are provided on all units, except the first unit in each unit group (i.e., on units 2, 3, 4, 5, and 6 on a six unit-one web press or units 2, 3, 4, and 6, 7, 8, of an 8 unittwo web press) Each unit is supplied with two blankets Set of web break detectors :

26 GOSS web break detectors are interfaced with GOSS Omnicon system to provide first out indication and self-arming interlocks, and severer/web catcher interface with web break detectors GOSS web break detectors are installed at the exit of each unit, inside and after the chill roll section. (1) Space for printing unit installed at a later date This space is located after the splicer and includes two extra rollers and brackets in S-wrap configuration The electrical supply is upgraded for this future retrofit (1) Set of spare covered rolls for one half unit Includes covered rolls for dampening and inking system for one half unit EIGHT (8) Spare blanket(s) (1) Stacked Duplex Press configuration with Dual Power Distribution Control system that allows the stacked unit arrangement to operate as two independent press lines or together. Conventional duplex arrangements include at least two folders Configuration includes per press one switchboard and one drive enclosure and for the total system one additional Slave Main Press Console Substructure for upper press, as per Seller s recommendations, must be provided by the PURCHASER. (1) Autoplate device for four units The two plate cylinders of each unit are equipped with an automatic plate-up system including : One upper retractable rack for one new plate One lower side movable rack for one new plate One pneumatically activated automatic tensioning system This system allows to change the plate without breaking the web The plate cylinders have no underpacking The maximum paper stock is 135 g/m 2 with 0.30 mm thickness plates and up to 200 g/m 2 with 0.35 mm thickness plates Autoplate mechanisms are designed to fullfil their functions only if handled in proper manner. They are not designed to withstand other

27 constraints. Therefore it is obviously prohibited to load them with any extra weights Correct function of such a system is warranted only if cleanliness and maintenance are insured by the printer as per operator manual (1) Set of connecting parts for BALDWIN blanket cleaner integration for 4 units (1) BALDWIN automatic blanket cleaner model Impact for 4 units Electronically controlled wash-up procedure, with the possibility of preselecting ten different wash-up programs. Automatic advance of wash-up cloth Impact system uses pre-soaked tissue rolls Controlled from the unit Omnicon console Two wash-up bars per perfecting unit, placed on the infeed side of the unit Three Prepac impregnated wash cloth rolls are supplied with each washer (1) Circulator and temperature control for reduced Alcohol printing (<10 % alcohol) TECHNOTRANS Gamma.c 600 combination unit for dampening solution cooling and ink roller temperature control for 5 units Integrated in one cabinet. Water cooled chiller for dampening solution circuit and ink roller temperature control circuit for connection to a central chill water supply Dampening solution circuit : Stainless steel tank with integrated filter box One circulation and one feed pump Integrated additive mixer type aquados.d 5 Intermediate tank located near the last unit for return of the dampening solution from the press to the delta.c unit Conductivity display on the circulator cabinet Ink roller temperature control circuit : The system works in closed loop circuit Electrical heating, for cold press start up Circulation pump Motor valves for temperature regulation of the return water coming back from the ink rollers (1) TECHNOTRANS ph value indication Display on the Tecon panel of the circulator cabinet

28 (1) GOSS patented active web catcher This system is fired by a web break detection system and catches the web via an air knife and two catching rollers in case of web break in the dryer or after the dryer (linked to Ecocool detection) The system is installed between last printing unit and dryer The efficiency rate of the system is above 90% (1) GOSS CONTIWEB dryer with integrated afterburner and Chill roll section ECOCOOL /T for one web max. speed 10.7 m/s (2110 fpm) for 90 gsm (61 lbs) paperweight max. speed 8.6 m/s (1700 fpm) for 135 gsm (91 lbs) paperweight The Ecocool/T dryer is a web offset dryer with the functions of drying, chilling and guiding the web integrated in one single system In the dryer section (Ecotherm concept with integrated afterburner) the printed web will be dried at low air temperatures. The dryer makes direct use of the energy contained in the solvents in the system by means of active concentration control. In the thermal afterburners the solvents are burnt to produce hot clean air. The solvent concentration is controlled through constant temperature and pressure measurements, steering the frequency controlled fans. The result is a reduction of the gas consumption depending on ink coverage, paperweight and speed The Ecocool system includes small-diameter chill rolls positioned very close to the exit of the drying section. This allows better contact of the web to the chill rolls, which increases efficiency and eliminates solvent condensation The web guide on the first chill roll makes this excellent concept complete In the cooling zone the web temperature is reduced at the dryer outlet by approximately 40 o C (72 o F) During production stops the dryer is kept at Stand-By temperature for quick restart Standard equipment and construction features : The Ecocool dryer is supplied as one complete unit Comply with the latest standards EN 1539, NFPA 86 and the directives of the VDI Three temperature zones : heating zone, drying zone, cooling zone and a chill section The air circulation system provides a high air volume to the patented "Crossjet" air nozzle bars Web temperature control by infrared camera, located between drying zone and cooling zone Two afterburner installations with heat exchangers and frequency controlled fans Door sensors for safety Nine small diameter chill rolls of which the fourth roll is driven by a frequency controlled AC motor Contiweb web guide system and web break detection Web tension measurement at the last roller Silicone applicator, before the first and the second chill roll, including reservoir and mixer, and including independent speed control of the silicone rollers

29 One basic water piping system including valve, pump and filter Modem connection for remote diagnosis system, customer to provide dedicated telephone line Minimum dynamic gas pressure (note) : 100 mbar 1.45 psi Maximum static gas pressure : 330 mbar 4.8 psi Gas type different from natural gas on request The performance of the dryer is as diagram showing speed limitation according to paper weight and ink coverage (1) GOSS CONTIWEB Remoistening & Advanced Silicone package for one web The Remoistening & Advanced Silicone Package consists of : The controls on the Silicon Applicators The silicone applicator will be equipped with small mix tanks for each silicone roller. Silicone oil out of the reservoir with the concentrated silicone and water are mixed in these small tanks for each applicator. The amount of silicone oil coverage and water can be controlled separately for each side of the web. All components are integrated in the Ecocool Remoistening system The absolute moisture content in the product after remoistening can be as high as 4,5%. Normal moisture values are in the range of 3.5 %. Note: remoistening system is integrated in the silicone applicator and controls (1) GOSS CONTIWEB Webbing-up chain for Ecocool/T 93 for one web (1) GOSS Multiple combination folder model JF-55 for one web The basic JF-55 folder is a single width combination folder with one rotary chopper fold assembly featuring very high production speeds and a single stream delivery for magazine products and a single stream delivery for tabloid products. It can produce at speeds of up to iph and consists of the following features : Lower folder : Forming rolls are provided at the former nose and are horizontally and vertically adjustable Two sets (upper and lower) of driven, 178 mm wide, air-loaded urethane pinch pulleys Circumferential perforator/scorer (in-line) mounted between the two sets of pinch pulleys and actuated via air cylinder. On-the-run depth and lateral adjustment is provided Cross perforator cylinders with on-the-run circumferential phasing and depth adjustment One part cutting cylinder with one knife box fitted with soft cheekwoods