ALKON INSTALLATION AND SERVICING MANUAL 18 R 24 R - 24 C 28 R - 28 C 35 R - 35 C. English th edition - 02/2009

Transcription

1 ALKON 18 R 24 R 24 C 28 R 28 C 35 R 35 C th edition 02/2009 INSTALLATION AND SERVICING MANUAL English

2 Warning: this manual contains instructions to be used exclusively by the installer and/or a competent person in accordance with the current laws in force. The end user MUST not make any alterations to the boiler. Failure to follow the instructions indicated in this manual, which is supplied with the boiler, could cause injury to persons, animals or damage to property. UNICAL shall not be held liable for any injury and/or damage. CONTENTS 1 GENERAL INFORMATION Symbols used in this manual Correct use of the appliance Water treatment Information to be handed over to the user Safety warnings Data badge General warnings TECHNICAL FEATURES AND DIMENSIONS Technical features Dimensions Main components Boiler water circuit Performance data according to the Standard UNI General features INSTRUCTIONS FOR THE INSTALLER General warnings Standard codes for installation Packaging Boiler location Dimensions for connecting the Alkon 28 to the external storage tank kit DSP Boiler installation Gas connection Central heating connections DHW connections Examples of system pipework connections Condensate drain Flue outlet installation Electrical connections General warnings Connection to mains supply 230V Access to the terminal block and external connections Outdoor sensor connection ONOFF digital room controller connection Modulating RT/OT room controller connection Layout of the electrical connection for zone control systems Wiring diagrams Functional flow wiring diagram for Alkon 24/28/35 C Functional flow wiring diagram for Alkon 18/24/28/35 R Jumper installation on the modulating board Filling the system Initial lighting Burner pressure adjustment Variation of output range SERVICING SCHEDULE Instructions for inspecting and servicing the appliance FAULT CODES CE CERTIFICATE... 47

3 General information 1 GENERAL INFORMATION 1.1 SYMBOLS USED IN THIS MANUAL When reading this manual particular care has to be given to the parts marked with the followings symbols: DANGER! Indicates serious danger for your personal safety and for your life WARNING! Indicates a potentially dangerous situation for the product and the environment NOTE! Suggestions for the user 1.2 A CORRECT USE OF THE APPLIANCE The ALKON appliance has been designed utilizing today s heating technology and in compliance with the current safety regulations. However, following an improper use, dangers could arise for the safety and life of the user or of other people, or damage could be caused to the appliance or other objects. The appliance is designed to be used in pumped hot water central heating systems and for the production of domestic hot water. Any other use of this appliance will be considered improper. UNICAL declines any responsibility for any damages or injuries caused by an improper use; in this case the risk is completely at the user s responsibility. In order to use the appliance according to the foreseen scopes it is necessary to carefully follow the instructions indicated in this manual. 1.3 WATER TREATMENT The hardness of the mains water supply conditions the frequency with which the DHW heat exchanger is cleaned. In hard water areas where the main water can exceed 15 f total hardness, a scale reducing device is recommended. The choice of this device has to be made taking into consideration the characteristics of the water. In order to improve the resistance to lime scale it is recommended to adjust the domestic hot water temperature as near as possible to the one you really require. We recommend you to check the state of cleanliness of the domestic hot water heat exchanger at the end of the first year and subsequently, on the basis of the lime scale found, this period can be extended to two years. 1.4 INFORMATION TO BE HANDED OVER TO THE USER The user has to be instructed on the use and operation of his heating system, in particular: Hand over these instructions to the end user, together with any other literature regarding this appliance placed inside the envelope contained in the packaging. The user has to keep these documents in a safe place in order to always have them at hand for future reference. Inform the user on the importance of air vents and of the flue outlet system, stressing the fact that is absolutely forbidden to make any alterations to the boiler. Inform the user how to check the system s water pressure as well as informing him how to restore the correct pressure. Explain the function of time and temperature controls, thermostats, heating controls and radiators, to ensure the greatest possible fuel economy. Remind the user that, in order to comply to the standards in force, it is necessary to inspect and service the boiler according to the current codes of practice and according to the schedule indicated in this manual by the manufacturer. If the appliance is sold or transferred to another owner or if the present user moves home and leaves the appliance installed, ensure yourself that the manual always follows the appliance so that it can be consulted by the new owner and/or installer. Failure to follow the instructions indicated in this guide, which is supplied with the boiler, could cause injury to persons, animals or damage to property. The manufacturer shall not be held liable for any such injury and/or damage. 3

4 General information 1.5 SAFETY WARNING WARNING! The installation, adjustment, and servicing of this appliance must be carried out by a competent person and installed in accordance with the current standards and regulations. Failure to correctly install this appliance could cause injury to persons, animals or damage to property. The manufacturer shall not be held liable for any injury and/or damage. DANGER! Servicing or repairs of the appliance must be carried out by UNICAL authorised service technicians; UNICAL recommends drawing up a service contract. Bad or irregular servicing could compromise the safe operation of the appliance, and could cause injury to persons, animals or damage to property for which UNICAL shall not be held liable. Alterations to parts connected to the appliance Do not carry out any alterations to the following parts: the boiler to the gas, air, water supply pipes and electrical supply to the flue pipe, safety relief valve and its drainage pipe to the constructive components which influence the appliance s safe operation WARNING! When tightening or loosening the screw pipe connections, use only adequate fork spanners. The improper use and/or the use of inadequate equipment can cause damages (for example water or gas leakages). WARNING! Indications for appliances operating with propane gas Ensure yourself that before installing the appliance the gas tank has been purged. For a correct purging of the tank contact the liquid gas supplier or a competent person who has been legally authorized. If the tank has not been correctly purged problems could occur during ignition. If this occurs contact the liquid gas tank s supplier. Smell of gas If you smell gas follow these safety indications: Do not turn on or off electrical switches Do not smoke Do not use the telephone Close the mains gas tap Open all windows and doors where the gas leakage has occurred Contact the gas society or a company specialized in installing and servicing heating systems Explosive and easily inflammable substances Do not use or leave explosive or easily inflammable material (as for example: petrol, paint, paper) in the room where the appliance has been installed. 4

5 General information 1.6 DATA BADGE CE Marking The CE marking documents that the boilers satisfy: The essential requirements of the Directive regarding gas appliances (Directive 90/396/CEE) The essential requirements of the Directive regarding electromagnetic compatibility (Directive 89/336/CEE) The essential requirements of the Efficiency Directive (Directive 92/42/CEE) The essential requirements of the low voltage Directive (Directive 73/23/CEE) A B C D E LEGEND: 1 = CE Surveillance notify body 2 = Boiler type 3 = Boiler model 4 = Number of stars (Directive 92/42/CEE) 5 = (S.N ) Serial number 6 = P.I.N. code 7 = Approved fluing configurations 8 = (N0x) N0x class A = Central Heating circuit features 9 = (Pn) Nominal output 10 = (Pcond) Condensing nominal output 11 = (Qmax) Nominal heat input 12 = (Adjusted Qn) Adjusted for nominal Heat input 13 = (PMS) Max. pressure C.H. system 14 = (T max) Max. C.H. temperature B = Domestic Hot Water circuit features 15 = (Qnw) Nominal heat input in D.H.W. mode (if different from Qn) 16 = (D) Specific D.H.W. flow rate according to EN 625 EN = (R factor) N taps based on the quantity of water declared EN = (F factor) N stars based on the quality of water declared EN = (PMW) Max. pressure D.H.W. system 20 = (T max) Max. temperature D.H.W system C = Electrical features 21 = Electrical power supply 22 = Consumption 23 = Protection grade D = Countries of destination 24 = Direct and indirect country of destination 25 = Gas family 26 = Supply pressure E = Factory setting 27 = Adjusted for gas type X 28 = Space for national brands 5

6 General information 1.7 GENERAL WARNINGS This instruction manual is an integral and indispensable part of the product and must be retained by the user. Please read carefully the instructions contained in this manual as they provide important indications regarding the safe installation, use and servicing of this appliance. Keep this manual in a safe place for future reference. The installation and servicing must be carried out in accordance with the regulations in force according to the manufacturer s instructions and by legally competent authorized persons. By a competent person, we imply a person who has a specific technical qualification in the field of components for central heating systems for domestic use, domestic hot water production and servicing. The person must have the qualifications foreseen by the current laws in force. Bad or irregular servicing could compromise the safe operation of the appliance, and could cause injury to persons, animals or damage to property. The manufacturer shall not be held liable for any such injury and/or damage. Before carrying out any cleaning or servicing turn off the electrical supply to the boiler by means of the ON/OFF switch and/or by means of the appropriate shutdown devices. Do not obstruct the inlet/outlet terminals. In the event of failure and/or faulty functioning of the appliance, switch off the boiler. Do not attempt to make any repairs: contact qualified technicians. Any repairs must be carried out solely by Unical authorized technicians and using only original spare parts. Nonobservance of the above requirement may jeopardize the safety of the appliance. To guarantee the efficiency and correct functioning of the appliance it is indispensable to have the boiler serviced annually by a qualified person. If the boiler remains unused for long periods, ensure that any dangerous parts are rendered innocuous. If the appliance is sold or transferred to another owner or if the present user moves home and leaves the appliance installed, ensure yourself that the manual always follows the appliance so that it can be consulted by the new owner and/or installer. Only original accessories must be used for all appliances supplied with optional extras or kits (including electrical ones). This appliance must be used only for the purposes for which it has been expressively designed. Any other use shall be considered incorrect and therefore dangerous. 6

7 Technical features and dimensions 2 TECHNICAL FEATURES AND DIMENSIONS The ALKON boiler is a thermal gas fired unit with an atmospheric fully premixed burner. These boilers are designed for use on the 2 nd family gas category II2H3P. Range of models available: ONLY CENTRAL HEATING PRODUCITON ALKON 18 R with an output of 18 kw ALKON 24 R with an output of 24 kw ALKON 28 R with an output of 28 kw ALKON 35 R with an output of 35 kw CENTRAL HEATING + DOMESTIC HOT WATER PRODUCTION ALKON 24 C with an output of 24 kw ALKON 28 C with an output of 28 kw ALKON 35 C with an output of 35 kw The ALKON boilers are supplied complete with all the safety and control devices in accordance with all the current regulations. Their technical and functional features comply with the regulations prescribed by the law No dated 06/12/ 1971, concerning safety and use of combustible gas and with the requirements prescribed in the law No. 10 dated 09/01/ 1991 and any subsequent amendments Gas Directive 90/ 396 CEE Efficiency Directive 92/42 CEE Electromagnetic Compatibility Directive 89/336 CEE Low Voltage Directive 73/23 CEE. DESCRIPTION OF COMPONENTS AND FEATURES Aluminium heat exchanger/condenser; Electronic ignition; Flame modulation in function of the absorbed power; Minimum heat output adjustment in CH mode; Electronic adjustment of the ignition ramp; Electronic frost protection mode; Pump overrun function; Safety high limit thermostat; Flow temperature sensor; Return temperature sensor; DHW temperature sensor (only on the ALKON C model); Three speed circulating pump with air vent; Expansion vessel; Automatic air vent; Low water pressure switch; Control panel with electrical protection IP X4D; Temperature water gauge; Illuminating led indicator for: power On, CH demand, burner ON, boiler lockout, fault code display; DHW temperature selector switch:35/60 C (only for the ALKON C model); CH temperature selector switch + summer/winter position; Reset/Chimneysweeper switch Rapid DHW delivery switch RIRA ((only for the ALKON C model); Steel wall mounting template for system pipework connections. Moreover, the boilers of the ALKON range are classified as CONDENSING BOILERS according to the Directive 92/42 CEE appendix 2 (4 stars) and appendix 6 (D.M 660). 2.2 DIMENSIONS A L P ALKON 18 24/28 35 A L P 325,5 325,5 325,5 7

8 Technical features and dimensions 2.3 MAIN COMPONENTS ALKON R ALKON C M G R M C G F R Bypass 2. Plate heat exchanger 3. Gas valve 4. Aluminium heat exchanger/condenser 5. Sealed chamber 6. Fan 7. Overheat safety thermostat 8. Ignition and flame detection electrode 9. Air vent valve 10. Flue outlet/combustion air inlet 11. Expansion vessel 12. Condensate drain siphon 13. Automatic air vent 14. Diverter valve motor 15. Diverter valve 16. Pump 17. Central heating circuit safety valve 18. System drain cock 19. Low water pressure switch 20. Flow switch 21. Domestic hot water temperature sensor 22. Filling system cock M C.H system flow (3/4 ) C DHW outlet (1/2 ) G Gas inlet (3/4 ) F Cold water inlet (1/2 ) R C.H. system return (3/4 ) 8

9 Technical features and dimensions 2.4 BOILER WATER CIRCUITS ALKON R 1. ByPass Gas valve 3. Central heating circuit safety valve Low water pressure switch Condensate drain siphon 9 6. Flow temperature sensor Return temperature sensor Aluminium heat exchanger/condenser Burner 11. Air vent 12. Premix 8. Safety thermostat 13. Fan Sealed chamber Flue outlet/combustion air inlet 16. Expansion vessel 17. Pump Filling system cock M G R C.H system flow Gas inlet C.H. system return ALKON C M G M C G F R F 21 R ByPass 2. DHW temperature sensor 3. Gas valve 4. Flow temperature sensor 5. Condensate drain siphon 6. Return temperature sensor 7. Safety thermostat 8. Aluminium heat exchanger/condenser 9. Burner 10. Air vent 11. Premix 12. Fan 13. Sealed chamber 14. Flue outlet/combustion air inlet 15. Expansion vessel 16. Diverter valve motor 17. Diverter valve 18. Automatic air vent 19. Low water pressure switch 20. DHW plate heat exchanger 21. Circulation pump 22. Central heating circuit safety valve 23. System drain cock 24. Domestic hot water flow restrictor 25. Flow switch 26. Cold water filter 27. Filling system cock M C.H system flow C DHW outlet G Gas inlet F Cold water inlet R C.H. system return 9

10 Technical features and dimensions 2.5 PERFORMANCE DATA ACCORDING TO STANDARD UNI For information regarding the adjustment of: INJECTORS BURNER PRESSURES DIAPHRAGMS OUTPUTS GAS CONSUMPTIONS please refer to the paragraph BURNER PRESSURE ADJUSTMENT. Heat output Nominal heat input Minimum heat input Efficiency at full load (100%) Required efficiency at full load (100%) Efficiency at 30% part load Required efficiency at part load (30%) Condensing nominal heat input Condensing minimum heat input Condensing efficiency at nominal load (100%) Condensing requested efficiency (100%) Condensing efficiency at 30% part load Condensing requested efficiency at part load (30%) Number of stars (according to CEE 92/42) Combustion efficiency at full load (100%) Combustion efficiency at reduced load Standby losses (max) (*) Flue gas temperature tfta (max) Flue gas mass flow rate (minmax) Air excess Condensate production max CO at 0% of O (min max) 2 N0x (value according to EN 297/A3 and EN 483) N0x class Flue losses with burner in operation (max) Flue losses with burner off (*) Room Temperature = 20 C ALKON kw kw kw % % % % kw kw % % % % n. % % % C g/s % kg/h mg/kwh mg/kwh % % 18 R 3, ,5 3,2 97,26 95,44 102,53 92,66 17,5 3,63 102,74 92,24 107,09 98, ,77 98,17 0,51 44,1 1,327,8 26,84 3, ,13 5 2,23 0, R 4,3 23,8 23,0 4,1 96,58 95,72 101,1 93,08 24,06 4,64 101,09 92,38 107,22 98, ,33 98,54 0,75 55,2 1,5810,43 20,57 4, ,62 5 2,67 0, C 4,3 23,8 23,0 4,1 96,58 95,72 101,1 93,08 24,06 4,64 101,09 92,38 107,22 98, ,33 98,54 0,75 55,2 1,5810,43 20,57 4, ,62 5 2,67 0, R 5, ,3 5,4 97,49 95,87 103,78 93,31 28,65 6,08 102,33 92,46 107,78 98, ,68 98,28 0, ,2312,84 26,84 4, ,65 5 2,32 0, C 5, ,3 5,4 97,49 95,87 103,78 93,31 28,65 6,08 102,33 92,46 107,78 98, ,68 98,28 0, ,2312,84 26,84 4, ,65 5 2,32 0, R 35 C 7,0 34,8 7,0 34,8 34,1 34,1 6,7 6,7 97,99 97,99 96,07 96,07 103,21 103,21 93,60 93,60 35,1 35,1 7,56 7,56 100,99 100,99 92,55 92,55 107,15 107,15 98,55 98, ,05 98,05 98,27 98,27 0,06 0,06 46,7 46,7 2,7515,96 2,7515,96 26,84 26,84 5,9 5, ,2 38, ,95 1,95 0,494 0,494 Technical data registered with the appliance operating with natural gas (G20) 2.6 GENERAL FEATURES Appliance s family gas category Min. water flow rate in CH circuit (Dt 35 C) Min. pressure in CH circuit Max. pressure in CH circuit Water content in primary circuit Max operating temp. in CH mode Min operating temp. in CH mode Total volume CH expansion vessel Total preloading expansion vessel Max water content CH circuit (calculated for a max temp. of 90 C) Min flow rate DHW circuit Min. DHW inlet pressure Max DHW inlet pressure DHW specific flow rate (Dt 30 C) DHW flow restrictor DHW production in continuous operation with Dt 45 K DHW production in continuous operation with Dt 40 K DHW production in continuous operation with Dt 35 K DHW production in continuous operation with Dt 30 K ( * ) DHW production in continuous operation with Dt 25 K ( * ) DHW adjustable temperature Electrical supply /power consumption Fuse rating Maximum absorbed power Electrical protection Net weight 10 ALKON l/min bar bar l C C l bar l l/min bar bar l/min. l/min. l/min. l/min. l/min. l/min. l/min. C VHz A (F) W IP kg 18 R II2H3P 1,31 0, ,4 230/ X4D 32,5 24 R II2H3P 1,67 0,5 3 2, ,6 230/ X4D C II2H3P 1,67 0,5 3 2, ,6 2 0,5 6 10,9 12 7,2 8,1 9,2 10,8 12, / X4D R II2H3P 2,21 0,5 3 2, ,6 230/ X4D 33,5 28 C II2H3P 2,21 0,5 3 2, ,6 2 0,5 6 12,5 12 8,69 9,8 11, , / X4D R II2H3P 2,73 0, ,7 230/ X4D 41,5 35 C II2H3P 2,73 0, ,7 2 0, ,82 11,1 12,6 14,7 17, / X4D 46 (*) mixed

11 3 INSTRUCTIONS FOR THE INSTALLER Instruction for the installer 3.1 GENERAL WARNINGS WARNING! This boiler has to be destined for the use for which it has been expressively designed for. Any other use shall be considered improper and therefore dangerous. This boiler is designed to heat water at a temperature inferior to boiling point at an atmospheric pressure. WARNING! These appliances are exclusively designed to be installed inside adequate sitings. Therefore these appliances must not be installed and operated outdoors. An outdoor installation could cause malfunctioning and could be dangerous. For external installations, it is recommended to use appliances which are specifically designed and predisposed for this purpose. Before installing the boiler the following points have to be carried out by a competent engineer: a) The whole system should be thoroughly flushed in order to remove any residual dirt or grime which could compromise correct boiler operation. b) Check that the boiler has been preset for operating with the gas type available. This is verifiable via the indication on the packaging and on the data badge; c) Check that the chimney/flue pipe has an adequate draught, does not have any constrictions, and that no other appliance s flue outlets have been fitted, unless the chimney is serving more than one heating appliance, according to the specific standards and regulations in force. The connection between the boiler and chimney/ flue outlet can be made only after this verification has been carried out. WARNING! In rooms where aggressive vapours or dust is present the appliance must operate independently from the air present in the boiler s location room! WARNING! The appliance must be installed by a qualified engineer, who complies to the technicalprofessional requirements according to the law 46/90 and whom, under his own responsibility, guarantees the compliance of the standards according to the latest regulations. WARNING! The appliance must be installed only on a vertical flat wall, made of non combustible material. The appliance must be positioned so that at least the minimum operational and servicing clearances are provided. NOTE: The boiler must be connected to a heating system which is compatible to its performance and output. 11

12 3.2 STANDARD CODES FOR INSTALLATION The ALKON boiler is a thermal unit designed for use with the family gas category II2H3P. The appliance must be installed in compliance to the instructions contained in this manual. The installation must be carried out by a competent qualified engineer, whom will assume the responsibility of complying to all the local and/or national regulations published in the official publications, as well as all the applicable codes of practice. The installation must be carried in accordance to the codes of practice, the regulations and the requirements hereby indicated, which constitute an indicative list, but not a complete one, as these continue to undergo developments. National installation regulations: Gas plants for domestic use fed by network distribution Standard UNICIG 7129 Gas plants for domestic use not fed by network distribution Standard UNICIG 7131 Law dated n 46 Law dated n 10 Other applicable statutory requirements: Law 1083/71 (ref. Standard UNI for the design, installation and maintenance). Law 46/90 and D.P.R. 447/91 Law 10/91 and D.P.R. 412/93 and subsequent amendments D.M Moreover, the boiler must be installed in accordance to all the regulations regarding the boiler room, and comply to the building regulations and the prescriptions regarding central heating plants in force in the country the boiler is installed. The appliance must be installed, commissioned and serviced according to the regulations in force. This is also valid for the hydraulic system, the flue outlet system and the boiler location room. 3.3 PACKAGING The ALKON range of boilers are supplied fully assembled in a strong cardboard box. Note: DO NOT DISPOSE OF PACKAGING IN THE ENVIRONMENT After having unpacked the boiler check that it is intact and undamaged. Keep the packaging material (cardboard box, plastic bags, polyester protection etc.) out of the reach of children as they can be dangerous. UNICAL refuses all liability for injury to persons, animals or damage to property deriving from not having respected the above mentioned recommendations. In the packaging, in addition to the boiler, you can also find the following contents: Service logbook User s instruction guide This installation and servicing manual Warranty Nr. 2 spare parts request coupons N 2 wall plugs for fixing the boiler to the wall Pipe kit Wall mounting template ALKON A B C

13 3.4 BOILER LOCATION When selecting the position for the installation of the boiler please comply to the following safety requirements: Fit the appliance in rooms protected from frost; In rooms where aggressive vapours or dust are present, the appliance must be able to operate independently from the air of the location room; The appliance must be installed exclusively on a vertical and solid wall, capable of adequately supporting the weight of the boiler; The wall must not be made of inflammable material; Leave a clearance of 50mm on each side of the boiler to facilitate subsequent servicing; Every appliance is supplied with a steel Wall mounting template which facilitates the connection of the gas and water feed pipes when laying out the hydraulic system and before installing the boiler. This template has to be fixed on to the wall chosen for the installation. The upper part of the template marks the position where to drill the holes for fixing the boiler support bracket to the wall. The lower part of the template marks the correct positioning of the system pipework connections for the following parts: M = CH system flow (3/4 ) C = Hot water outlet (1/2 ) G = Gas supply (3/4 ) F = Cold water supply (1/2 ) R = CH system return (3/4 ) ALKON 24/28/35 STEEL WALL MOUNTING TEMPLATE CODE: ALKON 18 STEEL WALL MOUNTING TEMPLATE CODE: M C G F R M G F R 13

14 HOW TO POSTION THE WALL MOUNTING TEMPLATE ON TO THE WALL a b b c c d d e e 70 mm (18 kw) 50 mm (2428 kw) 37 mm (35 kw) 110 mm POSITIONING OF THE SYSTEM PIPEWORK CONNECTIONS, CONDENSATE DRAIN AND PRESSURE RELIEF VALVE Pressure relief valve drain point 18 kw Condensate drain point 15 M G R a 24/28 kw Condensate drain point 10 Pressure relief valve drain point M C G F R kw Condensate drain point 4,5 Pressure relief valve drain point M C G F R Note: The pipework for the condensate drain point and pressure relief valve must be fitted under the lower part of the boiler. 14

15 Dimensions for the connection of the ALKON R 18 to the external storage tank kit DSP M 62,5 R 1948 Mc Mimp C Svs F Ri 97,5 62, Rc Rimp 15

16 3.5 BOILER INSTALLATION Before connecting the boiler to the heating system the following requirements must be carried out by competent and qualified engineers: a) The system is flushed out with a suitable product in order to eliminate any metallic tooling or welding residues and oil and grime which could reach the boiler and affect the proper running of the boiler; b) Check that the boiler has been preset for operating with the gas type available. This is verifiable via the indication on the packaging and on the data badge; c) Check that the chimney/flue pipe has an adequate draught, does not have any constrictions, and that no other appliance s flue outlets have been fitted, unless the chimney is serving more than one heating appliance, according to the specific standards and regulations in force. The connection between the boiler and chimney/flue outlet can be made only after this verification has been carried out. For fitting the boiler: Place the steel mounting template on to the wall. Determine the position of the holes for fixing the support bracket. Drill the holes and fix the support bracket using the fixing screws as indicated on page 14. Engage the boiler on to the support bracket. Mark the positions of the gas, cold water supply, hot water outlet, CH flow and return, pressure relief valve and/or condensate drain. Note: The appliances are equipped with expansion vessels. Before installing the appliance check that the vessel s capacity is sufficient; if this is not the case, provision must be made to fit an additional expansion vessel. 3.6 GAS CONNECTION DANGER! The gas connection must be carried out only by a qualified engineer who will have to respect and comply to the regulations in force and to the requirements indicated by the local gas supplier. An incorrect installation could cause injury to persons, animals or damage to property. The manufacturer shall not be held liable for any injury and/or damage. Before installing the boiler it is recommended to thoroughly clean all the fuel feed pipework in order to remove any eventual residual grime which could compromise the boilers correct functioning. If you smell gas: a. Do not turn on or off electrical switches, use the telephone or any other object which can provoke sparks; b. Open all doors and windows in order to allow fresh air to enter and purify the room; c. Close all gas cocks; d. Contact a service engineer, qualified installer or the gas supply company. As a safety measure against gas leaks, Unical recommends installing a surveillance and protective system composed of a gas leakage detector combined with an onoff selenoid valve fitted on the gas supply line. The gas supply pipe must have a section which is identical or greater then the one used on the boiler and must assure a correct gas pressure. It is however important to comply with the General installation standards indicated in the standards UNI 7129, UNI 7131 and UNI Before commissioning an internal gas distribution system and therefore before connecting it to the gas meter, the complete installation must be tested for gas soundness. If any part of the system is concealed from view the gas soundness test must be carried out before covering the pipes. Before connecting the pipework the system must be tested with air or inert gas at a pressure of at least 100mbar. Before commissioning the boiler ensure that the following operations are carried out: Open the gas meter cock and vent the air contained in the piping and subsequently proceed to vent device by device. Check, with the gas cock turned off, that there are no gas leaks. During the 2 nd quarter of the hour from the start of the test, no pressure reduction should be detected by the pressure gauge. Any gas leaks must be found by using only water soap solutions, or an equivalent product, and eliminated. Never look for gas leaks using a naked flame. 16

17 3.7 CENTRAL HEATING CONNECTIONS WARNING! Before installing the boiler we recommend that the system is flushed out with a suitable product in order to eliminate any metallic tooling or welding residues, oil and grime which could reach the boiler and affect the proper running of the boiler. Do not use any solvents for flushing out the system as they could damage the system and/or its components. Nonobservance of these instructions could cause injury to persons, animals or damage to property. The manufacturer shall not be held liable for any such injury and/or damage. The CH flow and return circuits have to be connected to the boiler via the respective connections ¾ M and R as indicated on page 14. When determining the size of the CH circuit pipes it is essential to bear in mind the pressure losses induced by the radiators, any eventual thermostatic radiator valves, lockshield valves and by the system s layout. The routing of the piping has to be laid down taking all the necessary precautions in order to avoid air locks and to facilitate the continuous purging of the system. The boiler is fitted with an automatic BYPASS (differential valve with a flow rate of about 150 l/h) which always ensures a minimum water flow rate to the heat exchanger even if, for example, all the thermostatic valves fitted on the heating system are closed. It is possible to adjust the bypass by acting on the adjustment screws. Alkon C Bypass adjustment clockwise anticlockwise ByPass CLOSED rotate the screw in a clockwise direction ByPass OPEN rotate the screw in a anticlockwise direction Alkon R Bypass adjustment ByPass CLOSED ByPass OPEN Ensure yourself that the system s piping is not used as earth clamps for the electrical or telephonic system. They are absolutely unsuitable for this use. In a short time this could cause serious damage to the piping, boiler and radiators. Pressure relief valve drain pipe In correspondence to the heating pressure relief valve provision should be made to install a discharge pipe with a funnel and a siphon which lead to an adequate drainage. The drainage has to be controllable by sight. WARNING! If this precaution is not taken it could lead to injury to persons, animals or damage to property. The manufacturer shall not be held liable for any such injury and/or damage. 17

18 BOILER CIRCULATION PUMP Graph Water flow rate/ available head for installation ALKON 18 kw 7,0 6,5 6,0 5,5 Available head (mc.a.) 5,0 4,5 4,0 3,5 3,0 2,5 2,0 1,5 1,0 0, Flow rate (Q) l/h BOILER CIRCULATION PUMP Graph Water flow rate/ available head for installation ALKON 24 kw 7,0 6,5 6,0 5,5 Available head (mc.a.) 5,0 4,5 4,0 3,5 3,0 2,5 2,0 1,5 1,0 0,5 BOILER CIRCULATION PUMP Graph Water flow rate/ available head for installation ALKON 28 kw 7, Flow rate (Q) l/h 6,5 6,0 5,5 Available head (mc.a.) 5,0 4,5 4,0 3,5 3,0 2,5 2,0 1,5 1,0 0, Flow rate (Q) l/h

19 BOILER CIRCULATION PUMP Graph Water flow rate/ available head for installation ALKON 35 kw Instruction for the installer 7,0 6,5 6,0 Available head (mc.a.) 5,5 5,0 4,5 4,0 3,5 3,0 2,5 2,0 1,5 1,0 0, Flow rate (Q) l/h 3.8 DOMESTIC HOT WATER CONNECTIONS (Model C ) WARNING! Before connecting the boiler to the water mains supply ensure that the system is flushed out with a suitable product in order to eliminate any metallic tooling or welding residues, oil and grime which could reach the boiler and affect the proper running of the boiler. Nonobservance of these instructions could cause injury to persons, animals or damage to property. The manufacturer shall not be held liable for any such injury and/or damage. The hot water distribution and domestic hot water supply pipework must be connected to their respective ½ boiler pipe connections C and F as indicated on page 14. The pressure in the system must be between 1 and 3 bar (if the pressure is higher fit a reducing pressure valve). WARNING! The hardness of the mains water supply conditions the frequency with which the DHW heat exchanger is cleaned. In hard water areas the opportunity of fitting an adequate scale reducing device for domestic purposes for treating the mains water supply to the boiler, in compliance to the DM n 443 dated 21/12/90, should be taken into consideration. Where water hardness exceeds 15 f, a scale reducing device is always recommended. Ensure yourself that the system s water and central heating piping are not used as earth clamps for the electrical or telephonic system. They are absolutely unsuitable for this use. In a short time this could cause serious damage to the piping, boiler and radiators. 19

20 3.9 EXAMPLES OF SYSTEM PIPEWORK CONNECTIONS CONNECTION WITH STRAIGHT PIPES Straight pipework kit (supplied with the boiler) CONNECTION WITH STRAIGHT PIPES + ONOFF VALVES (supplied with the boiler) (optional extra) CONNECTION WITH STRAIGHT PIPES + BICONIC NIPPLES Straight pipework kit supplied with the boiler) Telescopic pipes connection kit (optional extra) 20

21 3.10 CONDENSATE DRAIN During the combustion process the boiler produces condensate which, through the A pipe, flows into the siphon. The condensate which forms inside the boiler has to be routed into an adequate drain by means of the pipe B. DANGER! Before commissioning the appliance fill the siphon and check the correct drainage of the condensate. If the appliance is used with the condensate drain siphon empty there could be danger of intoxication resulting from the escape of flue gasses. The connection between the appliance and the sewage system must be carried out in compliance with the specific reference standards, and in particular: prevent the end user utilizing the condensate produced; a siphon must be fitted (supplied with the boiler); there must be no bottlenecks; the connection must be made just under the bottom part of the boiler; it must be installed so as to avoid freezing of the liquid when the boiler is operating and prevent the eventual pressurization of the sewage system; consent the correct downflow of the appliance s liquid discharges; it must be made with one of the following materials which are resistant to condensate: Grès, according to the Standards DIN and 6, EN 2951 or 2 or 3; Glass (boron silicate); Polyvinyl chloride (PVC), according to DIN V and 2, and DIN 19538; Polyethylene (PE) DH type, according to DIN and 2 and DIN and 2; Polypropylene (PP) and copolymer styrene (ABS) according to DIN V 19561; Polyesterific resin (GFUP), according to DIN ; Stainless steel. Condensate inlet coming from the heat exchanger B Condensate outlet, pipe to connect to the sewage system A Condensate inlet coming from the flue outlet 21

22 3.11 FLUE OUTLET INSTALLATION The flue system must be installed in accordance with the local and national Standards (refer to Standard UNICIG 7129, point 4 and UNICIG point 5). We recommend using only original UNICAL flue outlet systems. Damages caused by installation errors and for nonobservance of the instructions given by the same manufacturer will invalidate all the supplier s contractual or extra contractual responsibilities. If the boiler has to be replaced ALWAYS replace the flue outlet system. The boiler has been approved for the following flue configurations: C53 Boiler with separate air inlet and products outlet. These ducts can discharge into areas with different pressure. The two terminals must not be fitted on to two opposite walls. Type C63 Boiler designed for connection to a combustion air inlet and flue products discharge system approved and sold separately. C13 oiler designed for connection to horizontal inlet and outlet terminals, which admit fresh air to the burner and discharge the products of combustion to the outside through concentric or twin ducts. The minimum distance between the inlet air duct and the flue outlet duct must be of 250 mm and both terminals must be positioned within a 500 mm square section. C83 Boiler designed for connection to a terminal for the intake of combustion air and to an individual or collective chimney for the discharge of the products of combustion. The chimney must comply to the current regulations. C33 Boiler designed for connection to vertical inlet and outlet terminals, which admit fresh air to the burner and discharge the products of combustion to the outside through concentric or twin ducts. The minimum distance between the air inlet duct and the flue gas outlet duct must be of 250 mm and moreover both terminals must be positioned within a 500 mm square area. aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa C43 Boiler designed for connection to collective flue systems including two ducts, one for the air inlet and the other for the discharge of products of combustion through concentric or twin ducts. B23 Boiler designed to be connected to an open flue which will terminate vertically through the roof. The combustion air is withdrawn directly from the room where the boiler is installed. WARNING: for this type of connection the room must comply with the same installation regulations valid for open chimney boilers. The chimney must comply to the current regulations. 22

23 HORIZONTAL FLUE OUTLET WITH CONCENTRIC DUCTS Ø 60/100 mm Instruction for the installer Type C13 The minimum allowable length of the horizontal concentric pipes is of 0,75 metres. The maximum allowable length of the horizontal concentric pipes is of 3,5 metres. For each elbow added the maximum length permitted has to be reduced by 1 metre. pendenza 3% Important: the outlet/inlet flue has to have a minimum inclination of 3% towards the top in the outlet direction, so as to enable the collection of any condensate formed in the boiler (35 kw) KIT5800C 50 (2428 kw) 70 (18 kw) KIT5810C 118 Type C33 The maximum allowable length of the vertical concentric pipes is of 8,5 metres, apart from the terminal Ø 80/125. For each elbow added the maximum length permitted has to be reduced by 1 metre. KIT5820C KIT5740C

24 HORIZONTAL FLUE OUTLET WITH CONCENTRIC DUCTS D 80/125 mm Type C13 The minimum allowable length of the horizontal concentric pipes is of 0,75 metres. The maximum allowable length of the horizontal concentric pipes is of 6 metres. For each elbow added the maximum length permitted has to be reduced by 1 metre. Moreover, the flue outlet has to have a minimum inclination of 3% towards the top in the outlet direction, so as to enable the collection of any condensate formed in the boiler. 37 (35 kw) 50 (24 / 28 kw) 70 (18 kw) pendenza 3% Important: the outlet/inlet flue has to have a minimum inclination of 3% towards the top in the outlet direction, so as to enable the collection of any condensate formed in the boiler Type C33 The maximum allowable length of the vertical concentric pipes is of 8,5 metres, including the terminal Ø 80/125. For each elbow added the maximum length permitted has to be reduced by 1 metre. KIT5820C KIT5730C

25 FLUE OUTLET WITH SEPARATE DUCTS D 80 mm The maximum pressure loss permitted, independently from the type of installation, must not exceed the value of 100 Pa. 37 (35 kw) 50 (24 / 28 kw) 70 (18 kw) (r=d) 205 (r= ½D) 218 Ø 80 TSC0130C oppure TSC0150C KIT5780C KIT5770C It is not permitted to position the two terminals on opposite walls. 25

26 FLUE CONFIGURATION Ø 80 mm The maximum allowed pressure drop, apart from the installation type, cannot be higher than 100 Pa. CALCULATION OF THE PRESSURE LOSSES OF THE COMBUSTION AIR INLET/PRODUCTS OUTLET DUCTS When calculating the pressure losses bear in mind the following parameters: Example N.1 Intake of primary air from the perimeter wall and flue outlet from the roof. KIT5790C For the twin flue pipe system s adaptor, the pressure loss is of 4 Pa; For narrow radius 90 bend Ø 80 (R=½ D), the pressure loss is of 14 Pa; For each large radius 90 bend Ø 80 (R=½ D), the pressure loss is of 4 Pa; For each metre of Ø 80 flue pipe the pressure loss is of 1 Pa in the combustion air inlet; For each metre of Ø 80 flue pipe the pressure loss is of 1,5 Pa in the combustion product outlet; For the Ø 80 L=1 horizontal combustion air inlet terminal the pressure loss is of 3,5 Pa; For the Ø 80 L=1 horizontal combustion products outlet terminal the pressure loss is of 5,5 Pa; For the vertical flue outlet duct Ø 80 L=1 the pressure loss is of 8 Pa. KIT 5750C KIT 5760C Note: These values refer to flue systems made with original UNICAL non flexible and smooth pipes. KIT 5770C TSC0130C TSC0150C The maximum pressure drop of 100 Pa includes the losses created by: 1 adapter from 1 x Ø60/100 mm to 2 x Ø80 mm 2 wide radius curves + 1 exhaust terminal + 1 air intake terminal TSC0130C TSC0150C KIT5750C KIT 5760C KIT 5780C KIT 5750C KIT 5760C TSC0130C TSC0150C KIT5750C KIT 5760C KIT 5770C Example N.2 Intake of primary air and flue outlet from two external perimeter walls. It is not permitted to position the two terminals on opposite walls. 26

27 FLUE CONFIGURATION Ø 60 mm The maximum allowed pressure drop, apart from the installation type, cannot be higher than 60 Pa. CALCULATION OF THE PRESSURE LOSSES OF THE COMBUSTION AIR INLET/PRODUCTS OUTLET DUCTS Example N.1 Intake of primary air from the perimeter wall and flue outlet from the roof. KIT5790C When calculating the pressure losses bear in mind the following parameters: For the twin flue pipe system s adaptor, the pressure loss is of 4 Pa; For reducer M Ø80 / F Ø60 the pressure drop is 6 Pa in evacuation and 3 Pa in suction For reducer F Ø80 / M Ø60 the pressure drop is 6 Pa in evacuation and 3 Pa in suction For each large radius 90 bend Ø 60 (R=D), the pressure loss is of 4 Pa; For each metre of Ø 60 flue pipe the pressure loss is of 3 Pa in the combustion air inlet; For each metre of Ø 60 flue pipe the pressure loss is of 5 Pa in the combustion product outlet; For the Ø 60 L=1 horizontal combustion air inlet terminal the pressure loss is of 6 Pa; For the Ø 60 L=1 horizontal combustion products outlet terminal the pressure loss is of 10 Pa; For the vertical flue outlet duct Ø 80 L=1 the pressure loss is of 8 Pa Note: These values refer to flue systems made with original UNICAL non flexible and smooth pipes. The maximum pressure drop of 60 Pa includes the losses created by: 1 adapter from 1 x Ø60/100 mm to 2 x Ø80 mm 2 wide radius curves + 1 exhaust terminal + 1 air intake terminal + 2 reducer M Ø80 / F Ø Example N.2 Intake of primary air and flue outlet from two external perimeter walls. It is not permitted to position the two terminals on opposite walls. 27

28 3.12 ELECTRICAL CONNECTIONS The appliance s electrical safety is guaranteed only when the same appliance has been correctly earthed in compliance with the regulations in force. The gas and water feeding pipes and the CH system pipes cannot be used as ground plates. Ensure that the above safety electrical requirements subsist; in case of doubt, ask for a professionally qualified technician to check the appliance s electrical system. UNICAL refuses responsibility for any damages arising from failure to earth the boiler correctly. It is necessary that a qualified technician verifies that the electrical system is adequate to the appliance s maximum absorbed power, indicated on the data plate, verifying in particular that the section of the system s cables is suitable to the appliance s maximum absorbed power. For the appliance s general electrical supply the use of adaptors, multiple sockets and/or extension cords is strictly forbidden. The use of any power supplied equipment implies the observance of several fundamental rules, such as: Do not touch the appliance with any wet part of your body and/or barefooted; Do not pull the supply cables; Do not expose the boiler to sunlight, rain, etc., unless it is explicitly foreseen; Do not permit children or inexpert people to use the appliance. Note: It is necessary to fit a double pole switch on the electrical supply line, having a 3 mm contact separation in both poles, in an easy accessible position so as to ensure quick and safe servicing. The replacement of the supply cable as to be carried out by a qualified authorized UNICAL engineer, using only original spare parts. The nonobservance of the above could compromise the appliance s safety. Access to the electrical terminal block and external connections DANGER! Switch off and disconnect the electricity supply before carrying out any operations on the electrical parts. Remove the front panel. To gain direct access to the connection areas remove the 4 screws A and remove the cover B. Connection to mains supply 230V The boiler is provided complete with a 1,5 m long, mains supply cable, with a cross section area of 3x0,75 mm2. The boiler s electrical connections are shown in the section named WIRING DIAGRAMS (paragraph 3.13 pages 31 and 32) A mains supply of 230 V 50 Hz is required. The wiring to the boiler must be in accordance with the current CEI regulations. DANGER! The electrical connections must be carried out only by a qualified engineer. Before carrying out the connections or any other operation on the electrical parts, always switch off and disconnect the electricity supply and ensure yourself that it cannot be accidentally turned on. View of the terminal board after having removed the front cover 1L 2N Y2 Y1 28

29 Outdoor sensor connection (optional) DANGER! Switch off and disconnect the electricity supply before carrying out any operations on the electrical parts. Subsequently we have to make the maximum flow temperature correspond to the minimum external temperature by setting the Otc parameter (outdoor sensor setpoint) Remove the 4 screws A and remove the cover B Gain access to the external terminal strip Y1 Connect the outdoor sensor by wiring it onto the terminal strip Y1 to the connection terminals 2 and 3 and wire it to the terminal 1 for their electric shielding. This adjustment must be made via the knob positioned on the rear side of the panel (turn the knob in an anticlockwise direction between a value from 10 to 19). Obviously this temperature is different from zone to zone and varies in function of the climatic conditions of the installation site (it corresponds to the minimum design temperature). The minimum flow temperature instead (HL) is automatically set by the boiler when the outdoor temperature is +20 C. Once these parameters have been set the boiler will choose a flow temperature on the heating curve on the basis of the outdoor sensor readout. With this solution it is possible to control the flow temperature according to the variations of the outdoor temperature. However, it is necessary to configure the heating curve. The curve can be drawn by setting the maximum and minimum flow design temperatures: the first one must be selected on the boiler (via the C knob on the control panel max. setting 80 C), whilst the second is set at 30 C (MINIMUM HEATING TEMPERATURE). Note: This adjustment could be susceptible to subsequent slight changes in function of the outdoor sensor s location. 29

30 ONOFF digital room controller connection (optional) DANGER! Switch off and disconnect the electricity supply before carrying out any operations on the electrical parts. TA Gain access to the terminal strip Y2 Remove the existing jumper positioned between the terminals 34 and in its place connect the RT cable, making it pass through an extractible grommet available on the control box. A4 A3 A2 A5 A1 A6 A8 1L 2N Y2 Y1 A11 Modulating RT/OT digital room controller connection (optional) WARNING! The modulating room controllers must be supplied by Unical. DANGER! Switch off and disconnect the electricity supply before carrying out any operations on the electrical parts RT/OT Gain access to the terminal strip Y Connect the TA modulating cable to the terminals 45 of the terminal strip Y1, making them pass through an extractible grommet available on the control box. Remove the jumper positioned between the terminals 34 on the terminal strip Y2. A4 A3 A A5 A1 A6 A8 1L 2N Y2 Y1 A11 30

31 Layout of the electrical connections for zone control systems Instruction for the installer N 1L 2N Y2 Y1 External voltage line L Room thermostat (high temperature zone controller) Boiler flow Digital room controller (low temperature zone controller) ON OFF Low temperature zone High temperature zone 3 M 4 Boiler return When the thermostat s contact (OnOff) is closed, the 3 way valve opens the high temperature zone and closes the low temperature zone (controlled by the digital room controller Regolafacile ). To the terminals 3 and 4 on the Y2 connector Note: The terminal connections 3 and 4 indicated in the diagram refer to the valve s internal limit stop, when the same valve is in the low temperature position. With the thermostat s contact (OnOff) open, the 3way valve deviates towards the low temperature zone (the temperature value can be adjusted with the digital room controller). To the terminals 3 and 4 on the Y2 connector N External voltage line L N External voltage line L TA TA Flow LT zone HT zone Flow LT zone HT zone 3 M 4 3 M 4 Return Return The microswitch on the 3way valve closes whilst the room thermostat is demanding heat when the diverter valve reaches the low temperature position and sends the request to the boiler. The 3way valve has to use the limit switch contact in order to simulate this type of request. 31

32 3.13 WIRING DIAGRAMS FUNCTIONAL FLOW WIRING DIAGRAM ALKON 24/28/35 C VG E.ACC./RIL. P VM BROWN LIGHT BLUE TRASF. ACC. DK WHITE BROWN YELLOW/GREEN BROWN BLACK ORANGE BLUE LIGHT BLUE TL BLACK LIGHT BLUE BROWN YELLOW/GREEN LIGHT BLUE BROWN RED WHITE GREEN MDV SR LIGHT BLUE LIGHT BLUE 230 V 50 Hz To the general bipolar switch (installer) SRR WHITE WHITE YELLOW/GREEN BROWN LIGHT BLUE BLACK GREEN GREEN A4 A5 A1 A6 A8 X3 Y2 Y1 A11 FL A3 BROWN WHITE A2 SS RED RED A9 A1...A11 = Service connectors DK = Minimum water pressure switch E.ACC/RIL = Ignition/detection electrode FL = Minimum flow switch MVD = Diverting valve motor P = Circulating pump SR = CH flow sensor SRR = CH return sensor SS = DHW sensor TL = Limit thermostat VG = Gas valve VM = Modulating fan Y1 = Connector: Outdoor sensor modulating room thermostat Y2 = Connector: Line voltage On/Off room thermostat (230 V) 32

33 FUNCTIONAL FLOW WIRING DIAGRAM ALKON 18/24/28/35 R Instruction for the installer VG E.ACC./RIL. P VM BROWN LIGHT BLUE TRASF. ACC YELLOW GREEN BROWN BLACK ORANGE BLUE LIGHT BLUE BLACK LIGHT BLUE BROWN YELLOW/GREEN LIGHT BLUE BROWN DK WHITE BROWN TL RED WHITE GREEN MDV (preset) SR LIGHT BLUE LIGHT BLUE 230 V 50 Hz To the general bipolar switch (installer) SRR WHITE WHITE YELLOW/GREEN BROWN LIGHT BLUE BLACK GREEN GREEN A4 A5 A1 A6 A8 X3 Y2 Y1 A11 A3 A2 SS (preset) BROWN LIGHT BLUE A9 A1...A11 = Service connectors DK = Minimum water pressure switch E.ACC/RIL = Ignition/detection electrode P = Circulating pump SR = CH flow sensor SRR = CH return sensor TL = Limit thermostat VG = Gas valve VM = Modulating fan Y1 = Connector: Outdoor sensor modulating room thermostat Y2 = Connector: Line voltage On/Off room thermostat (230 V) 33

34 JUMPER LOCATION The jumpers, fitted on to the modulation board, have the purpose of determining several indispensable functions for correct boiler operation. JP1: NIGHT REDUCTION The Night reduction function is enabled if the jumper is linked between terminals 1 and 2. The Night reduction function is excluded if the jumper is linked between terminals 2 and 3 (factory set configuration). DANGER! Disconnect and switch off and electrical supply before carrying out any operations on the electrical parts. To gain access to the jumper: Remove the front panel Undo the 4 screws A and remove the cover B JP1 NIGHT SHIFT OFF OFF Jp1 If the jumper is positioned on NS (12), the high temperature zone is in permanent demand. As the high temperature demand has priority on the low temperature demand, the eventual action of the digital remote room controller is completely uninfluential. The closure of the contact between 34 on the Y2 provokes the night reduction mode as illustrated in the graph on page 28. The opening of the contact between 34 on the Y2 restores the selected setpoint temperature and/or renders it independent from the outdoor compensation if an outdoor sensor is fitted. To disenable the central heating demand it is necessary to turn the CH knob to the minimum setting. The night reduction s default value is 5 (corresponding to 10 C). This value can be changed via the TSP 1 on the digital room controller from 5 (10 C) to 30 (35 C). JP2: GAS TYPE For boilers operating with LPG, the jumper has to be linked between the connectors 1 and 2. For boilers operating with natural gas the jumper has to be linked between the connectors 2 and 3. GPL JP2 MET JP2 GPL MET

35 3.14 FILLING THE SYSTEM Warning! Do not mix the CH system s water with unsuitable antifreeze products (example: antifreeze solutions for motor vehicles) or use wrong concentrations of anticorrosion solutions! This could cause damage to the washers and could provoke noise during normal boiler operation. If really necessary, use exclusively specific antifreeze products suitable for use on aluminiumsilicon alloy. UNICAL refuses all liability for injury to persons, animals or damage to property deriving from not having respected the above mentioned recommendations. After completing all the system s service connections the circuits may be filled by carefully following out the following phases: open the radiator s air vents and check that the automatic air vent in the boiler is working properly. gradually open the appropriate filling cock and check that the automatic air vents fitted onto the system are working properly. NOTE: The minimum low water pressure switch will not give the electrical impulse to fire the burner if the pressure is lower then 0,4 bar. The pressure of the water in the CH system must not be lower then 0,8/1 bar; if this value is lower use the filling cock on the boiler to adjust the pressure. This operation must be carried out when the system is cold. Use the pressure gauge fitted on the boiler to read the circuit s pressure value. NOTE! If the boiler has not been fired for a long period the pump could be jammed. Before firing the boiler, it is important to carry out the following unjamming operation: place a cloth underneath the pump remove the pump vent plug positioned in the centre of the pump using a screwdriver, rotate the shaft in a clockwise direction. Once this operation has been concluded, screw back the pump vent plug and check that there have been no water leaks. FILLING COCK OPEN CLOSE close the radiator s air vents as soon as water begins to flow out. using the pressure gauge check that the pressure reaches the value of 0,8/1 bar. WARNING! After removing the pump vent plug some slight water leakage could occur. Before replacing the front panel dry all the wet surfaces. close the filling cock and then bleed off the air once again through the radiator s air vents. check all the connections for soundness. after having fired the boiler and the system has reached the correct temperature, stop the pump and repeat the air bleeding operations. let the system cool down and, if necessary, reestablish the water pressure to 0,8/1 bar. 35

36 3.15 INITIAL LIGHTING PRELIMIARY CHECKS The first ignition must be carried out by a qualified technician. Failure to do so could cause injury to persons, animals or damage to property. UNICAL shall not be held liable for any injury and/or damage. Before lighting the boiler check that: the boiler installation has been carried out in accordance with the specific Standards UNI 7129 and 7131 for the gas part and the Standards CEI 648 and 649for the electrical part; the combustion air inlet and the discharge of the products of combustion occur in the correct way in accordance to the specific Standards in force (UNI 7129/7131); the gas supply system is correctly dimensioned for the boiler s output; the boiler s electrical supply is 230 V 50 Hz; the system has been filled with water (pressure registered on the gauge 0,8/1 bar with pump not running); any of the system s onoff valves are open; the mains supply gas corresponds to the one which the boiler has been calibrated for: otherwise convert the boiler to use the available gas (refer to section: GAS CONVER SION ); this operation must be carried out by a qualified technician in compliance to the regulations in force; the gas supply cock is open; there are no gas leaks; the external mains supply switch is on; the boiler system s safety valve is not blocked and that it is connected to the sewage system; the condensate drain siphon has been filled with water and that it is connected to the sewage system; there are no water leaks; all the necessary ventilation conditions and minimum clearance distances are guaranteed for subsequent servicing in case the boiler is sited in a cupboard compartment. LIGHTING AND SHUTTING DOWN PROCEDURES For lighting and shutting down the boiler refer to the USER S INSTRUCTIONS GUIDE. Information to be passed on to the user The user must be instructed on the use and operation of his boiler and in particular detail: Hand over to the end user the booklet: USER S INSTRUC TIONS GUIDE, as well as all the other literature relative to the appliance and placed in the envelope contained in the packaging. The user must retain this literature for any future reference. Inform the user of the importance of the air vents and of the flue outlet system, stressing the fact that absolutely no alteration can be made. Inform the user regarding the control of the system s water pressure and how to restore it to the correct value. Explain and demonstrate to the user the correct function and adjustment of the temperature, thermostats and radiators for the economic use of the system. Remind the user that in order to comply to the regulations in force the boiler has to be inspected and serviced regularly as indicated by the manufacturer. If the appliance is sold or transferred to another owner or if the present user moves home and leaves the appliance installed, ensure yourself that the manual always follows the appliance so that it can be consulted by the new owner and/or installer. DANGER! Before firing the appliance fill up the siphon through the filling hole and check the correct drainage of the condensate. If the appliance is used with the condensate drain siphon empty this could cause poisoning caused by the leakage of the flue gasses. 36

37 3.16 BURNER PRESSURE ADJUSTMENT WARNING! All the instructions indicated below are for the exclusive use of qualified UNICAL service technicians or installers. If necessary correct the value by turning the adjustment screw A in a CLOCKWISE direction to decrease the value and in an ANTICLOCKWISE direction in order to increase it. All the boilers leave the factory already calibrated and tested. If it is necessary to change the calibration due to gas conversion or adaptation to the mains supply system, the gas valve must be recalibrated. Warning: during this operation do not request any domestic hot water. A) MAX OUTPUT ADJUSTMENT Remove the cap and connect a suitable C0 2 gas analyser to the sampling point in the flue inlet/outlet terminal. MAXIMUM OUTPUT ADJUSTMENT SCREWS B) MIN OUTPUT ADJUSTMENT By pressing the Reset G key again the boiler will operate at the minimum output (led D and led E = blinking). Press the Reset G key for at least 3 seconds. The boiler will operate in the CH mode at the maximum output (led D = blinking and led E = ON ). 3 sec. The chimney sweeper mode remains active for 15 minutes. To disenable the chimney sweeper mode before this time has run out, press the Reset G key for at least 3 seconds. Check that the C0 2 values are within the values indicated in the table Burner pressures. Check that the C0 2 values are within the values indicated in the table Burner pressures. 37

38 If necessary correct the value by turning the adjustment screw B in a CLOCKWISE direction to increase the value and in an ANTICLOCKWISE direction in order to decrease it. C) COMPLETION OF THE BASIC ADJUSTMENTS Check the C0 2 values at the minimum and maximum output. If necessary make the required adjustments. To ensure correct boiler operation the C0 2 values have to be adjusted with extreme care respecting the values indicated in the table. Close the sampling test point in the flue inlet/outlet terminal with the appropriate cap C. MINIMUM OUTPUT ADJUSTMENT SCREWS In case of gas valve replacement or difficult ignition: Screw down completely the maximum adjustment screw A in a clockwise direction, than slacken for 7 turns. Check the boiler ignition; if the boiler goes into lockout slacken the screw A again of one turn, than retry ignition. If the boiler goes into lockout again, carry out the above indicated operations until the boiler is fired. At this point carry out the burner adjustment as previously indicated. 38