Certification All contractors shall be licensed to perform work in district area

Transcription

1 Wil-Fra-Mar Building 320 East Vermont Street Indianapolis IN (fax) General Provisions A/E Spec # Standard Project Certification All contractors shall be licensed to perform work in district area Coordinate Coordinate work in this Section with Section Alternatives Coordinate work in this Division with work being performed by other Contractors is necessary Coordinate work in this Section with Section Summary of the Work Temporary Work A/E Spec # Standard Project Shop Drawings Conformance Temporary lighting shall conform to current OSHA and NEC standards for type and wiring. Coordinate Coordinate with Section Temporary Facilities Page 1 of 38

2 IPS Electrical Design A/E Spec # Standard Project Compliance All work in this Division shall comply with National, State and Local Electrical Codes Experience Electrical Contractors bidding project shall have been in business doing projects equal to or greater is size for a minimum of 5 years Apprentice shall not work on "LIVE" circuits with out Joneyman Electrician present. Industrial Technology areas shall have own panel board with a minimum of 8 pushbuttons in room for shunt tripping of panel board. Rigid conduits are required in Boiler Rooms, Outdoor and Damp locations. On larger schools provide portable generator connection at service with Kirk-Key interlocks. Service conduits above ground are to be rigid. Minimum size of conduit 3/4" A/E shall do a Fault/Coordination study to set and coordinate trip settings. Follow current NEC code for GFCI protection No MC cable A Foreman must be present on the job site at all time Do not leave "LIVE" panels unattended. Page 2 of 38

3 Basic Material and Methods A/E Spec # Standard Project Test Reports Coordinate Coordinate work with Section Alternatives that may affect the Work of this Section Coordinate work with Division 2 Site Work that may affect the Work of this Section Raceway A/E Spec # Standard Project Conduit A/E Spec # Standard Project Unless otherwise noted provide (4) 3/4" spare EMT conduit for each flush mounted distribution panel board. Coordinate conduit type with building design and IPS Master Specifications Page 3 of 38

4 Wire and Cable A/E Spec # Standard Project All work shall conform to requirements of NEC Cable sheath colors are as follows: Red - Fire Alarm - no wire larger than #14 AWG will be permitted White - Security/Video/Data Blue - Data Orange - Fiber Green - Telephone Coordinate cable type and color coding with IPS Master Specifications Use of "BX", "AC" or "MC" cable is not permitted Aluminum Conductors are not permitted All cables shall be plenum rated Power System Wire Connections and Devices A/E Spec # Standard Project O.Z. Electrical Manufacturing Co. Burndy Engineering Company Thomas & Betts Company Design Standard O.Z. Electrical Manufacturing Co. Compression lugs shall be equal to T&B and series Page 4 of 38

5 Medium Voltage Cables, Splices, Terminations A/E Spec # Standard Project Wire and Cable American Insulated Wire Corporation B.I.C.C. The Okonite Company Tpirelli Cable Corporation Southwire Splicing and Terminating Burndy Corporation Cadweld (Ericl Products, Inc.) Cooper Power Systems MAC Products, Inc. Minnesota Mining and Manufacturing Company (3M) The Okonite Company Raychem Corporation Thomas and Betts Corporation Pull Boxes A/E Spec # Standard Project Size and gauge of boxes shall conform to the NEC Install where boxes will be accessible, but not to be conspicuous. Coordinate Coordinate exact locations of pull boxes with other trades. Page 5 of 38

6 Outlet Boxes A/E Spec # Standard Project Conformance Outlet Boxes shall conform to the NEC Coordinate Coordinate size and location of boxes with schedule in IPS Master Specification Section Wiring Devices A/E Spec # Standard Project Hubbell Pass & Seymour Leviton Cooper Wiring Devices Key switches are required in Hallways/Corridors, Restrooms, and Locker rooms. In Hallways/Corridors use a 3-way switching method with key switches in the center and normal switches by doors for Fire Dept. use. Make sure not all lights are turned off by normal snap switches. Hubbell is the only accepted manufacturer for key switches. Coordinate Coordinate manufacturer and model number with schedule in IPS Master Specification Section Page 6 of 38

7 Lighting Control Devices A/E Spec # Standard Project Field quality-control test reports Operation and Maintenance Data Contactors and Relays Automatic Switch Co. GE Lighting Controls Hubbell Lighting, Inc. Square D Co.; Power Management Organization Allen Bradley ITE Siemens Cutler Hammer Photoelectric Relays Intermactic, Inc. Paragon Electric Co., Inc. Testing Systems shall be field tested prior to Building Substantial Completion Training Factory-authorized representative shall train Owner's maintenance personal and the systems Wall packs only for emergency lighting No battery ballasts No Central batteries systems Page 7 of 38

8 Motors A/E Spec # Standard Project Marathon Baldor GE US Motors All motors to be high efficiency type Starters, Disconnects, and Controllers A/E Spec # Standard Project Westinghouse G.E. Company Square D company ITE Siemens Allen Bradley Furnas Page 8 of 38

9 Switchboards A/E Spec # Standard Project Square D Company General Electric Co. Cutler-Hammer ITE Siemens All Electrical Distribution Equipment shall have Copper busses with bolt in breakers Main service switches over 1000 amps shall have GFCI protection School shall have one main service disconnect Hinged covers required Switches over 1200 amps shall be bolted pressure type, high pressure contact (HPC) unacceptable. A/E shall do a Fault/Coordiantion study to set and coordinate trip settings. All Branch Switches to have visible blade construction, shrouded blades unacceptable. Metering System Switchboards shall have CM3350 metering system manufactured by Square D. No Equal. Metering System Options to Include Disturbance Detection of surges and sags lasting. Ethernet communication card with both fiberoptic and 10baseT connections with web server. 63 rd harmonic resolution 128 samples /cycle Downloads capable of being done via RS-485 up tp 38.4K Baud, or optional Ethernet ports up to 100M Baud Boolean alarms combine up to other alarms with AND, NAND, NOT, OR, and XNOR Onboard Logging 8MB non-volatile memory record pre-set parameters at 100 msec interval during events Page 9 of 38

10 Panelboards and Cabinets A/E Spec # Standard Project Square D Company General Electric Co. Cutler-Hammer ITE Siemens Fusible Panelboards shall be equal to Square D Co. model QMB Computer boards shall have an 200% neutral isolated ground Units shall have Copper busses with bolt in breakers Hinged covers required Any circuit over 100 amps shall be fused and fed from switchboard Installation of Switchboards, Panelboards and Cabinets A/E Spec # Standard Project Internal heaters if required Immediate disconnect at service conduits entrance to the building or service encased in concrete. Nema 3R top in damp locations No outdoor gear Chillers and Electric heat to have separate utility meters if seasonal shutdown is feasible and IPL is agreeable Page 10 of 38

11 Switches A/E Spec # Standard Project Cutler-Hammer General Electric Co. Square D Company ITE Siemens Outdoor security lights to be on photo cell with no timers Coordinate Coordinate switch type with schedules in IPS Master Specifications Fuses and Fuse Holders A/E Spec # Standard Project Extra Material Provide wall mounted fuse cabinet or baked enamel finish, located where directed. Furnish 10% of each size and type, but not less than one (1) set of three (3) each of each size and type of fuses used in all motor control centers, power panels, disconnects, and the like, rated 600 amperes or less, and including those fuses and fuse supplied by others with integrated equipment. Contractor shall furnish Owner one (1) set of three of each size and type of all fuses installed in the main distribution center. For all fuses larger than 601 amperes, furnish two (2) spare fuses of each size. Bussman Ferraz-Shawmut Distribution fuses - Class "J" Service fuses - Class "L" Page 11 of 38

12 Circuit Breakers A/E Spec # Standard Project Westinghouse General Electric Co. Square D Company ITE Siemens Keep breakers to 100 Amps or less Coordinate Coordinate Circuit Breaker type with schedules in IPS Master Preventative Maintenance and Refurbishment of Circuit Breakers Standard Project A/E Spec # Personnel Qualifications Contractor to provide list of the qualified personnel who will perform the inspection, refurbishment, testing. List the years of experience and training of each of the personal. Similar Projects The Contractor shall provide details of not less than (2) similar projects as part of the Shop Drawing process Test Results Test results in accordance with the manufacturer's written recommendations. High voltage maintenance Energy Systems Maintenance Permier Power Certification Must be tested by Qualified Test Technicians - trained in National Electrical Testing Association (NETA) procedures and specifications Page 12 of 38

13 Hangers and Support Devices A/E Spec # Standard Project Coordinate Coordinate load limits with IPS Specifications Hangers shall be individual ring or clevis type, one-hole straps or multiple trapeze hangers. No more than two (2) struts shall be installed on hangers Material shall be similar to Uni-strut or equal Emergency Generator System A/E Spec # Standard Project Special Product One year from date of project Substantial Completion Schematic wiring drawing, dimension drawings and interconnection diagrams Kohler Onan Caterpillar Generator shall be load tested prior to Substantial Completion Fuel: Natural Gas. 100kw or larger use Diesel Generator shall have a remote annunciator panel located as directed Connect computer loads sump pumps and Technology type equipment to generator. Page 13 of 38

14 Power Factor Correction Capacitors A/E Spec # Standard Project s shall be certified by the manufacturer that all points in the specifications shall be met ABB Aerovoc Inc. Commonwealth Sprage Capacitor Inc. General Electric Company Square D Staco Energy Products Co. Power Survey Manufacturer shall be a member of NEMA Capacitors shall meet of exceed standards, equal to or in excess of those specified by NEMA, AIEE, MEC, or ANSI Furnish one (1) central system at service - no individual motor units Floor mounted capacitors shall be provided with a 5-1/2" high concrete pad MV Fused Load Interrupter Switch Refurbishment A/E Spec # Standard Project If switch is subject to moisture retro-fit humidistat controlled heaters in switch Verify Verify all door interlocks and devices are functional Page 14 of 38

15 Service and Distribution A/E Spec # Standard Project Secondary power distribution system will be 208V/120V, 3 phase 4 wire, wye 480V/277V 3-phase 4-wire or 480V 3-wire shall be used for equipment or motor loads only Branches to fluorescent lighting in general will be 120V Surge Suppressor (TVSS) A/E Spec # Standard Project Special Product 5 years parts and labor from date of project Substantial Completion Current Technologies Liebert Cutler Hammer Square D Company Siemens Intermatic Inc. (All devices must have covers) Mount in Service and Panelboards Incorporate on main switchgear Page 15 of 38

16 Grounding A/E Spec # Standard Project Compliance Grounding system shall be in full compliance with all provisions of the National Electrical Code and NFPA 70 For linear ground grid, use 15' rods 15' apart with minimum bare 4/0 bare AWG. Bury cables and rods minimum 3' deep in soil/grade For triangular ground grid use 15' copper rods 15' apart minimum Dry-Type Transformer A/E Spec # Standard Project s shall be certified by the manufacturer that all points in the specifications shall be met Cutter-Hammer General Electric Company Hevi-Duty Square D Company ITE Siemens Floor mounted transformers shall be provided with a 5-1/2" high concrete pad Must be acceptable ambient DB level at minimum load Install K-13 rated transformers on all computer Panelboards Page 16 of 38

17 Oil Filled Transformers A/E Spec # Standard Project s shall be certified by the manufacturer that all points in the specifications shall be met Cutter-Hammer General Electric Company Hevi-Duty Chance Kuhlman McGraw-Ed Miagra H.K. Porter Vantran RTE Cooper Manufacturer shall be a member of NEMA Transformers shall meet or exceed standards, equal to or in excess of those specified by NEMA, MEC, or ANSI C/T's incorporated in pad mounts if they are service transformers Transformer shall pad mounted and protected by bollards Page 17 of 38

18 Motor Control Centers A/E Spec # Standard Project Special Product 1 year from date of project Substantial Completion Shop Drawings Manufacturer's Certifications Schematic and elementary diagrams Square D Company General Electric Company Cutler-Hammer Siemens Testing Each unit shall be operationally field tested Adjustable solid state overload relays required Copper buss required Motors over 2 hp shall have single phase protection Furnish 10% spare fuses (not less than 6) of each type and rating shown on the Contract Drawings per Specifications Units over 1000 amp shall have GFCI protection Work In Existing Buildings A/E Spec # Standard Project Shut down of any electrical systems require a minimum of one (1) week notice to the Owner and District Electrical Forman (Mike Fox) Contact Numbers: Electric Shop: Dispatch: Mike Fox (cell): Page 18 of 38

19 Lighting A/E Spec # Standard Project The contractor shall provide and/or install sample fixtures, upon request of the Architect/Engineer for each fixture Photometric data for each fixture Outdoor and Security lighting shall be on photo cell with no timers No modular plug wiring systems Coordinate specifications with drawings and schedules Fixtures shall be direct wired - no master slave systems Rooms shall have multi level switching All fixtures shall be accessible with normal hand tools and 8' ladder Locate fixtures so that scaffolding or ladders over 8' are not required to change lamps Lamps, Ballasts, Accessories A/E Spec # Standard Project Report of ballast check All ballast shall be checked prior to Substantial Completion SP41 T-8 lamps District standard All ballasts to be rapid start unless otherwise approved by Owner F32T8 Tri phosphor 3050 lumens (acceptable) All ballasts to be electronic and meet all energy standards Coordinate lamps, ballasts, and accessories with lighting fixtures Page 19 of 38

20 Stage Dimming System A/E Spec # Standard Project Special Product One (1) year from date of project Substantial Completion Shop Drawings Klieg Brothers Lighting Co. Lighting Methods Inc. Color Tran Altman Lighting, Inc. EDI MX Series and Twilite System dimming equipment SSRC SL Series distribution equipment Coordinate Coordinate system requirements and approved model numbers for equipment with IPS Master Specifications Dimming Rack Install Dimming rack in room with filtered A/C Upon any renovations do the following Install 3 wire ground circuits Replace border lights with 4 color units White, Blue, Red, Green Replace all cords including all cords to flying color bars Remove all asbestos wiring Neutral required for each branch circuit Install "Road Show" switch with 200 amp shunt trip Floor pocket to have grounded outlets Install proper stain relief on all cords All cables shall be marked with metal tags indicating circuit number corresponding to dimmer terminal strip Page 20 of 38

21 Football - Lighting Pole A/E Spec # Standard Project Finish samples for selection by Architect All poles to have safety cable that runs the length of pole to tie safety climbing lanyards to Poles to have cage with climbing pegs Metal Halide fixtures with remote panel board/ballast at pole base Carbon Monoxide Control and Alarm System A/E Spec # Standard Project Shop Drawings Maintenance Manuals ACME Engineering Products, Inc. Mine Safety Appliances Company Greystone Vulcain, Inc. Back-Up Battery System shall include rechargeable back-up battery, minimum capacity four (4) hours Dock Areas Dock areas to have separate system Provide Spare Components Five (5) cans of analyzed gas for periodic field calibration checks and motorized dampers, smoke control and smoke evaluation control systems. Six (6) sets of spare fuses of each type One (1) remote sensor station Page 21 of 38

22 keeping System A/E Spec # Standard Project Shop Drawings Samples for color selection by Architect Daktronics Fair-Play BB Sportable ALL boards to have hinged rock shield Provide "school name" on board LED type lamps Lightning Protection System A/E Spec # Standard Project Complete Design Drawings Shop Drawings Advanced Lighting Technology Thompson Lighting Protection Harger Lightning Protection East Coast Lightning Equipment Capitol Lighting Lightning Protection Page 22 of 38

23 Fire Alarm and Detection System A/E Spec # Standard Project Special Product The equipment manufacturer shall make available to the owner a maintenance contract proposal to provide a minimum of two (2) inspections and tests per year in compliance with NFPA-72H guidelines Extra Material Vendor shall provide 10% of each type device for spare parts Shop Drawings The system manufacturer shall be responsible for furnishing engineering drawings which indicate the interlocking of all equipment external to the various control panels. Wiring Diagram Complete wiring diagram of the system Pyrotronics MXL IQ Notifier AFP200, AM2020, AM1010 The entire installed system and all integrated system operations shall be within the guidelines of Underwriter's Laboratories, Inc. Criteria Equipment shall be manufactured by ISO 9001 certified company All systems shall have an RS-232 port and panel mounted printer Coordinate Coordinate system equipment and operations with IPS Master Specifications The system shall be coordinated with all wall mount electromagnetic door holders Coordinate with Section "Alternatives" that may affect the work of this Section Spare Capacity System shall have 20% spare capacity System Circuit Wiring Conductors shall be no less than 18 AWG (1.02mm) and no larger than 14 AWG (1.63mm) on system circuit wiring Page 23 of 38

24 Training Contractor or Manufacturer's Representative shall provide two, 1-hour training sessions for building personnel and four, 4-hour training sessions for telecommunications department personnel Security System A/E Spec # Standard Project Shop Drawings Security Head in shall be Vista 50, Vista 128b Ademco SM4100 RS-232 card Panasonic multiplexer WJFS616 All outside ground floor rooms shall have motion detection if an outside exit door or window is present in room Pelco EM1450 enclosure arm Ademco 6139 keypads Panasonic WVCP234 digital camera Altronics ALTV624 camera power supplies Altronics SMP3 power supplies Panasonic WJ-NT104 Camera servers Pelco DF8A camera dome with ceiling plate Pelco EH outdoor enclosure with sunshield Ademco Quest 2000 motion detectors Computer by Contractor current model with CD rom 64M ram (3) serial ports network card Keyboard and Mouse (8) port switch (1) 3-1/2" floppy (2) parallel ports Screw terminal blocks Page 24 of 38

25 Clocks A/E Spec # Standard Project Atomix - American Signal 12 inch (round) Usually bought and installed by Owner Telephone System "TTC" A/E Spec # Standard Project Nortel Norstar OX32MICS (small buildings) Elementaries Meridian Option II (Large buildings) MS & HS Elementary Office phones 7324, classroom 7208 Coordinate 4" PVC conduit MS/HS Office phones 2008 and 2316, classrooms 2500 wall mount Page 25 of 38

26 Central Sound System "CS" A/E Spec # Standard Project Catalog Cuts of all products Shop Drawings Bogen Multicom 2000 Dukane MCS 350 Rauland Telecenter ICS Coordinate Coordinate Section Alternatives if needed Coordinate equipment with IPS Master Specifications Page 26 of 38

27 Dining/P.E. Gym Sound System A/E Spec # Standard Project List of projects and experience Location of local service facility and name(s) of trained testing personnel Shop Drawings Catalog Cuts of all products Cassette Tape Deck Tascam 202mk3, or equal CD Changer Tascam CD-305, or equal Equalizers Rane RPM 26v, or equal Feedback Suppresser (may not be needed) Sabine FBX-1020Plus, or equal Loudspeakers Atlas/Soundolier Model FC series, CF series, or equal Mixers TOA A-900MK2, or equal Power Amplifiers TOA P-9xxMK2 series, or equal, Crown ComTech series, or equal Experience Contractor shall have a minimum of five (5) years experience in similar size projects Frequency Response 70 Hz to 2,000 Hz, plus/minus 3 db Intelligibility %ALCons equal to or less than 10% (room empty) Service Contractor shall have local service facility within sixty (60) miles of the Owner's district boundaries, with authorized service personnel. Service personnel shall have TEF 20 equipment for testing and be trained in the operation of the testing equipment Sound Coverage Uniformity Plus/minus 3 db Page 27 of 38

28 Sound Pressure Level 86 db SPL with 6dB of headroom Testing Contractor shall provide testing of entire system with Architect/Engineer and Owner's Representative present Coordinate Coordinate equipment with IPS Master Specifications IPS Master Specification list single manufacturer, coordinate approved manufacturers Page 28 of 38

29 Gym Sound System "GSS" A/E Spec # Standard Project Shop Drawings Catalog Cuts of all products List of projects and experience Location of local service facility and name(s) of trained testing personnel Assistive Listening System Telex ST-200, or equal Telex ST-200, or equal Cassette Tape Deck Tascam 202mk3, or equal CD Changer Tascam CD-305, or equal Equalizers Rane RPM 26v, or equal Feedback Suppresser (may not be needed) Sabine FBX-1020Plus, or equal Loudspeakers Eastern Acoustic Works (EAW) MQ series, or equal Mixers TOA A-900MK2, or equal Power Amplifiers Crown K series, Crest CKS series or equal Wireless Microphone System Shure UC4/ Shure UC2/87, or equals Experience Contractor shall have a minimum of five (5) years experience in similar size projects Frequency response 100 Hz to 4,000 Hz, plus/minus 3 db Intelligibility %ALCons equal to or less than 12% (room empty) Page 29 of 38

30 Service Contractor shall have local service facility within sixty (60) miles of the Owner's district boundaries, with authorized service personnel. Service personnel shall have TEF 20 equipment for testing and be trained in the operation of the testing equipment Sound Coverage Uniformity Plus/minus 3 db Sound Pressure Level 107 db SPL with 6dB of headroom Testing Contractor shall provide testing of entire system with Architect/Engineer and Owner's Representative present Coordinate Coordinate equipment with IPS Master Specifications IPS Master Specification list single manufacturer, coordinate approved manufacturers Page 30 of 38

31 Auditorium Sound System "AS" A/E Spec # Standard Project List of projects and experience Catalog Cuts of all products Shop Drawings Location of local service facility and name(s) of trained testing personnel Assistive Listening System Telex ST-200, or equal Automatic Mixer IED 4800, EV 2508, or equal Cassette Tape Deck Tascam 202mk3, or equal CD Changer Tascam CD-305, or equal DAT Deck Tascam DA-40, or equal Effects Loudspeakers Renkus-Heinz Model TR series, or equal Equalizers Shure P4800, Rane RPM 26v, or equal Lobby Loudspeakers Atlas/Soundolier Model FA134, or equal Main Cluster Loudspeakers Renkus-Heinz CE series, or equal Manual Mixers TOA A-900MK2, or equal Mixing Console Soundcraft K1 24 Channel, or equal Power Amplifiers Crown K series, Crest CKS series or equal Theatrical Intercom System Clear-Com MS-232, or equal Wireless Microphone System Shure UC4/ Shure UC2/87, or equals Page 31 of 38

32 Experience Contractor shall have a minimum of five (5) years experience in similar size projects Frequency response, assistive listening system 100 Hz to 6,000 Hz, plus/minus 3 db Frequency response, main system 50 Hz to 15,000 Hz, plus/minus 3 db Intelligibility %ALCons equal to or less than 6% (room empty) Service Contractor shall have local service facility within sixty (60) miles of the Owner's district boundaries, with authorized service personnel. Service personnel shall have TEF 20 equipment for testing and be trained in the operation of the testing equipment Sound Coverage Uniformity Plus/minus 3 db Sound Pressure Level 96 db SPL with 6dB of headroom Testing Contractor shall provide testing of entire system with Architect/Engineer and Owner's Representative present Coordinate Coordinate equipment with IPS Master Specifications IPS Master Specification list single manufacturer, coordinate approved manufacturers Page 32 of 38

33 Football Sound System "FSS" A/E Spec # Standard Project Catalog Cuts of all products Shop Drawings Location of local service facility and name(s) of trained testing personnel List of projects and experience Assistive Listening System Telex ST-200, or equal Cassette Tape Deck Tascam 202mk3, or equal CD Changer Tascam CD-305, or equal Equalizers Rane RPM 26v, or equal Feedback Suppresser (may not be needed) Sabine FBX-1020Plus, or equal Field Intercom System Clear-Com WBS-6, Telex BTR-500, or equal Interior Loudspeakers Atlas/Soundolier C10A, or equal Main Filed and Concessions Area Loudspeakers Community R2 and WET series, or equal Mixers TOA A-900MK2, or equal Power Amplifiers Crown ComTech series, or equal Wireless Microphone System Shure UC4/ Shure UC2/87, or equals Experience Contractor shall have a minimum of five (5) years experience in similar size projects Frequency response 100 Hz to 2,500 Hz, plus/minus 3 db Page 33 of 38

34 Intelligibility %ALCons equal to or less than 10% Service Contractor shall have local service facility within sixty (60) miles of the Owner's district boundaries, with authorized service personnel. Service personnel shall have TEF 20 equipment for testing and be trained in the operation of the testing equipment Sound Coverage Uniformity Plus/minus 3 db Sound Pressure Level 92 db SPL with 6dB of headroom Testing Contractor shall provide testing of entire system with Architect/Engineer and Owner's Representative present Coordinate IPS Master Specification list single manufacturer, coordinate approved manufacturers Coordinate equipment with IPS Master Specifications Page 34 of 38

35 16782A - Television Distribution System A/E Spec # Standard Project Shop Drawings Location of local service facility and name(s) of trained testing personnel List of projects and experience Amplifiers Blonder Tongue, or equal Directional Couplers TrueSpec, or equal F Connectors Pico Macom, or equal Trunk Cable, Runs greater than 500 feet, RG-6 Helix , or equal Trunk Cable, Runs less than 500 feet, RG-11 Comscope 2285k, or equal Bandwidth 20 MHz to 300 MHz Experience Contractor shall have a minimum of five (5) years experience in similar size projects Maximum Signal Loss through System 40 db Service Contractor shall have local service facility within sixty (60) miles of the Owner's district boundaries, with authorized service personnel. Service personnel shall have TEF 20 equipment for testing and be trained in the operation of the testing equipment Testing Contractor shall provide testing of entire system with Architect/Engineer and Owner's Representative present Trunk Attenuation (Channel 13) Not more than 2.1 db Trunk Attenuation (Channel 83) Not more than 4.5 db Page 35 of 38

36 Coordinate Coordinate equipment with IPS Master Specifications Page 36 of 38

37 16782B - Television Distribution System A/E Spec # Standard Project Location of local service facility and name(s) of trained testing personnel List of projects and experience Operational Manuals Shop Drawings Blonder Tongue Jerrold Amplifiers Blonder Tongue, or equal Directional Couplers TrueSpec, or equal F Connectors Pico Macom, or equal Trunk Cable, Runs greater than 500 feet, RG-6 Helix , or equal Trunk Cable, Runs less than 500 feet, RG-11 Comscope 2285k, or equal Bandwidth 20 MHz to 300 MHz Experience Contractor shall have a minimum of five (5) years experience in similar size projects Maximum Signal Loss through System 40 db Service Contractor shall have local service facility within sixty (60) miles of the Owner's district boundaries, with authorized service personnel. Service personnel shall have TEF 20 equipment for testing and be trained in the operation of the testing equipment Testing Contractor shall provide testing of entire system with Architect/Engineer and Owner's Representative present Trunk Attenuation (Channel 13) Not more than 2.1 db Page 37 of 38

38 Trunk Attenuation (Channel 83) Not more than 4.5 db Coordinate Coordinate equipment with IPS Master Specifications Design Standards Blonder Tongue used as design standards for Specifications in IPS Master Specifications Television Equipment A/E Spec # TV Mounting Brackets Peerless Industries: Combination ceiling plate and TV mount bracket - JM S 2650D and Combination wall mount bracket and TV mount bracket - JMW2650D with extension column Hand Dryers A/E Spec # Standard Project Shop Drawings Electric Aire Model "F" Bobrick Model "B-751" Excel Model "R76-C" World Dryer Install Prision grade units only Mounting heights shall comply with Americans with Disability Act (ADA) Install as indicated on drawings Page 38 of 38