Intelligent Security & Fire

Transcription

1 AV Disc Recorder WJ-DR200 ENGLISH FRANÇAIS Before attempting to connect or operate this product, please read these instructions carefully.

2 ENGLISH VERSION PREFACE... 1 FEATURES... 1 PRECAUTIONS... 2 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS... 3 Front View... 3 Rear View... 5 INSTALLATION AND SYSTEM CONNECTIONS... 7 INSTALLATIONS... 7 SYSTEM CONNECTIONS... 8 SETUP PROCEDURES MAIN Menu SET UP Menu System Menu Recording Mode Menu Multi Shot Recording Setup Time Lapse Recording Menu CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SER- VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PER- SONNEL. SA 1965 SA 1966 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CONTENTS 3. Manual Time Lapse Alarm Recording Menu Time Lapse Program Timer Setup Alarm Recording Menu SEARCH/PLAY Menu System Information Menu Label Setup Password Setup OPERATING PROCEDURES FORMATTING THE DISC STATUS DISPLAY RECORDING PLAYBACK APPENDIX SPECIFICATIONS ACCESSORY For U.S.A Warning: This equipment generates and uses radio frequency energy and if not installed and used properly, i.e., in strict accordance with the instruction manual, may cause harmful interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. The serial number of this product may be found on the rear of the unit. You should note the serial number of this unit in the space provided and retain this book as a permanent record of your purchase to aid identification in the event of theft. Model No. Serial No. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

3 PREFACE The WJ-DR200 AV Disc Recorder can record up to 28,000 freeze pictures with a resolution of 720 x 480 (Fine Mode) on a large capacity optical disc (DVD- RAM). It can be set up to respond automatically to a sensor or alarm signal by recording the associated pictures. FEATURES Records clear freeze pictures Applies 3D Scan Conversion to record blur-compensated, clear freeze pictures from moving images. Vertical resolution is nearly double that of conventional VCR pictures. Reliable recording of events Obtain reliable records of important events by selecting the recording mode best suited for your purpose. There are three recording modes: Single Shot Recording: Records a single freeze picture. Multi Shot Recording: Records a continuous series of freeze pictures. Time Lapse Recording: Records freeze pictures at regular intervals. Easy picture search Three search modes for quick and easy picture search. List Search: Searches a list by recording date and time. Thumbnail Search: Searches displayed thumbnail images of recorded pictures. Direct Search: Searches by a recording date and time or record number directly specified by the user. Other handy recording functions Use the program timer function to preset the recording time and mode for each day of the week. Two video input channels for simultaneous recording of images from two cameras. Connect two Disc Recorders in series for uninterrupted recording when the disc of one recorder is full. ENGLISH -1-

4 PRECAUTIONS Refer all work related to the installation of this product to qualified service personnel or system installers. Do not block the ventilation opening or slots on the cover. To prevent the appliance from overheating, place it at least 5 cm (2 inches) away from the wall. Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service. Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance. Handle the appliance with care. Do not strike or shake, as this may damage the appliance. Fully charge up the backup battery. Keep the appliance turned on for at least 48 hours to recharge the backup battery. This procedure is necessary when using the appliance for the first time or after it has been unplugged for a long time from the AC outlet. Insufficient charging of the battery may cause erasure of settings if the AC power supply should fail. The battery, if fully charged, will back up the settings for 480 hours in an ordinary environment. We recommend that you note down your settings and retain them. Power or battery failure may erase settings you entered. Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do take immediate action if the appliance becomes wet. Turn the power off and refer servicing to qualified service personnel. Moisture may damage the appliance and also cause electric shock. Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently. Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do not use the appliance in an extreme environment where high temperature or high humidity exists. Use the appliance at temperatures within +5 C C (41 F F) and a humidity below 90 %. The input power source for this appliance is 120 V AC 60 Hz. -2-

5 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS Front View DISC CONTROL REMOTE ALARM PUSH OPEN PUSH OPEN RESET OPERATE ALARM REC REC R A M DISC AV Disc Recorder WJ-DR REMOTE OPERATE RESET ALARM REC REC DISC ALARM ALARM REC STANDBY 1. Operate indicator (OPERATE) Is on (green) when the Disc Recorder s power is turned on. 2. Remote indicator (REMOTE) Is on (orange) when the Disc Recorder is controlled by an outboard device through the Serial Control port (50). 3. Alarm Reset button (RESET) Cancels an activated alarm and resets the system to the condition prior to alarm activation. 4. Alarm indicator (ALARM) Lights (red) for two seconds when an alarm is activated and then starts blinking. Pressing the Alarm Reset button (3) will turn off the indicator. INDDEX FIND SET UP/ESC DISC KEEP COVER CLOSED TO PREVENT INSIDE FROM DUST SET PLAY MODE 1 ALL PLAY BACK SELECT PAUSE PLAY T/L MODE FORMAT + REC BUSY LOCK OFF ON STOP OPEN/ CLOSE ARARM REC STANDBY INDDEX FIND SET UP/ESC SET CONTROL PLAY MODE 1 ALL PLAY BACK SELECT PUSH OPEN PAUSE AV Disc Recorder WJ-DR 5. Alarm Recording indicator (ALARM REC) Is on (green) when the Disc Recorder is in Alarm Recording mode. 6. Recording indicator (REC) Is on (red) when the Disc Recorder is recording, and blinks when it is on standby for recording. 7. Disc indicator (DISC) Blinks/lights (red) when the recording capacity of the DVD-RAM disc is running low. (Blinks at 10% remaining space, blinks rapidly at 5%, and changes to steady light at 1%.) While overwriting in endless recording, continues to turn on for two seconds and off for half a second. PLAY T/L MODE FORMAT + REC LOCK OFF ON STOP OPEN/ CLOSE -3-

6 8. Disc cover Prevents dust from entering into the disc drive. Press to open. Do not open except to load or unload a disc. 13. Eject hole For sliding out the disc tray manually (by inserting a wire) if it is not ejected automatically when pressing the OPEN/CLOSE button (35). 9. Ventilation holes Allow air to enter the device to prevent it from overheating. Make sure not to block these holes. 10. Control Panel cover Press to open for access to the control buttons on the Control Panel. 11. Busy indicator (BUSY) Is on (green) when a disc is loaded. Is on (orange) when the disc drive is in operation. It also indicates an error condition in the disc recorder by blinking in green as follows: Blinks rapidly three times, followed by a 1-second interval. 0.2s 0.2s 1.0s An error has occurred on the disc in use. The disc is about to reach the end of its life cycle and should be replaced. Blinks rapidly twice, followed by a 1-second interval. 0.2s 0.2s 1.0s The unit s lens or disc needs cleaning. See page 46. Blinks once, followed by a 1-second interval. 0.2s < < 1.0s 21. Find button (FIND) Press to directly specify and play back a frame* Index button (INDEX) Press to search the disc for a recorded frame. 23. Alarm Recording button (ALARM REC STAND- BY) Enables/disables alarm recording. 24. Reverse Record button ( ) Left button Press to move the playback operation back one step to the previous record* 1. In the setup operation, moves the cursor to the left or select a parameter in reverse. 25. Reverse Frame button ( ) Down button Press in paused playback to move the playback operation back one step to the previous frame. In the setup operation, moves the cursor down one line. 26. Advance Frame button ( ) Up button Press in paused playback to advance the playback operation one step to the next frame. In the setup operation, moves the cursor up one line. 27. Set button (SET) In frame search, press to apply the entered value. In the setup operation, press to execute a selection and enter the submenu associated with the selected item. 28. Advance Record button ( ) Right button Press to advance the playback operation one step to the next record. In the setup operation, moves the cursor right or select a parameter forward. < Abnormal temperature rise inside the unit. Turn the power off and refer servicing to qualified service personnel. 12. Shutter For loading/unloading the disc. Pressing the OPEN/CLOSE button (35) on the Control Panel with the Disc Cover open will open the shutter and slide out the tray. 29. Pause button (ypause) Press to temporarily pause playback. Holding down the Pause button and pressing the REC button (31) will place the device into recording standby status. 30. Reverse Playback button (A) Press to play back frames in the reverse order they were recorded in. Holding the button down will speed up reverse playback, releasing it will restore the normal speed. -4-

7 31. Recording button (REC) Pressing the REC button will start recording in the previously defined mode. 32. Playback button (B) Pressing the (B) button will start playback. Holding the button down will speed up playback, releasing it will restore the normal speed. 33. Lock switch (LOCK OFF/ON) In ON position, locks out control of the Disc Recorder from the Control Panel and Parallel Control port (49). Keep normally in OFF position. 34. Stop button (STOP) Pressing the STOP button will terminate all modes of operation, such as recording, playback and setup. 35. Open/Close button (OPEN/CLOSE) Press to slide the disc tray out or in for loading or unloading a disc. Disabled while the Disc Cover (8) is closed. 36. Increment button (D+) Pressing the (D+) button in playback will decrease the playback speed. Rear View OUT B VIDEO IN A S-VIDEO VIDEO OUT S-VIDEO POWER 120V AC 60 Hz 38W VIDEO OUT 1V [ p-p ] 75Ω Manufactured by Matushita Communication Industrial Co. Ltd Yokohama Japan FOR COMMERCIAL USE ONLY AUDIO OUT IN Made In Japan PARALELL CONTROL SERIAL CONTROL SER. NO. 6ZA Looped Through Output B connector (B, OUT) The NTSC composite video signal B connected to VIDEO IN B (42) is looped through to this connector. Provided with automatic 75 Ω termination. 42. Video Input B connector (VIDEO IN, B) For input of the NTSC composite video signal from an outboard device. 43. Looped Through Output A connector (A, OUT) The NTSC composite video signal A connected to VIDEO IN A (44) is looped through to this connector. Provided with automatic 75 Ω termination. 44. Video Input A connector (VIDEO IN, A) For input of the NTSC composite video signal from an outboard device. LED MONITOR GND SENSOR IN ALARM IN ALARM RESET IN SERIES REC IN TIME ADJUST IN GND ALARM OUT ALARM RECOVER OUT ALARM REC REC DISC BUZZER OUT SYSTEM ERROR OUT THERMAL ERROR OUT TIME ADJUST OUT SERIES REC OUT CAMERA SW OUT OUTPUT LEVEL H L Pressing it in paused playback will increment the playback channel (or camera ID). To play back the selected channel, press the PLAY BACK SELECT button (38). 37. Decrement button (C ) Pressing the (C ) button in playback will increase the playback speed. Pressing it in paused playback will decrement the playback channel (or camera ID). To play back the selected channel, press the PLAY BACK SELECT button (38). 38. Playback Select button (PLAY BACK SELECT) Pressing the PLAY BACK SELECT button after selecting the input channel with the (D+) (36) or (C ) (37) button will start playback of the respective channel. 39. Setup/Escape button (SET UP/ESC) Used in the Disc Recorder s setup operation. Pressing the button for about two seconds will establish Setup mode and display the Setup menu window. Pressing it in a menu will return you to the previous menu window. To terminate setup, press again for about two seconds. SIGNAL GND CAUTION ATTENTION - FOR CONTINUED PROTECTION AGAINST FIRE HAZARD REPLACE ONLY WITH SAME TYPE FUSE - AFIN D' ASSURER UNE PROTECTION PERMANENTE CONTRE LES RISQUES D' INCENDIE REPLACER UNIQUEMENT PAR UN FUSIBLE DE MEME TYPE 120V AC 60Hz 125V 4 A 45. S-Video Input connector (VIDEO IN, S-VIDEO) For input of the S-video signal from an outboard device. 46. Video Output connector (VIDEO OUT) Outputs the selected composite video signal for the monitor. The A input images are displayed during recording, except when A and B inputs are recorded at a capture rate of one second or more. 47. S-Video Output connector (VIDEO OUT, S- VIDEO) Outputs the selected S- video signal for the monitor. The A input images are displayed during recording, except when A and B inputs are recorded at a capture rate of one second or more. POWER ON OFF -5-

8 48. Audio Output/Input connectors (AUDIO OUT/IN) Provided for recording and playback of audio signals. 49. Parallel Control port (PARALLEL CONTROL) For connecting an outboard device used to remote control the Disc Recorder. 50. Serial Control port (SERIAL CONTROL) For connecting a Personal Computer and the like to remote control the Disc Recorder. 51. Camera Switching Output connector (CAMERA SW OUT) Outputs a pulse after each recorded frame. 52. Terminal Board For connecting output and input signals to and from outboard devices. 53. Alarm Output Level selector (OUTPUT LEVEL H/L) Switches the output level of the ALARM OUT and ALARM RECOVER terminals on the Terminal Board (52). The factory default is L. Alarm Output Alarm Recover Output 0 V 0 V H 12 V 5 V 5 V 0 V 5 V 0 V 54. Cooling fan Prevents temperature rise inside the unit. 55. AC socket For connecting the supplied power cord. 56. Power switch (POWER ON/OFF) Turns the power of the Disc Recorder on and off. L * 1 : A record is a batch of freeze pictures (frames) recorded in one recording session. * 2 : One recorded freeze picture is called a frame. -6-

9 INSTALLATION AND SYSTEM CONNECTIONS INSTALLATIONS The installations described below should be made by qualified service personnel or system installers. Mounting in the Rack 1. Remove the four rubber feet by removing the four screws from the bottom of the Disc Recorder. 3. Install the Disc Recorder with the rack mounting brackets in the rack by using four screws (not included). OPERATE Remove four rubber feet. 2. Place the rack mounting brackets on both sides of the Disc Recorder and tighten them with the four supplied screws (M4 X 10). OPERATE OPERATE Cautions: Do not block the ventilation opening or slots in the cover to prevent the appliance from overheating. Always keep the temperature in the rack within +40 C (104 F). Secure the rear of the appliance to the rack by using additional mounting brackets (procured locally) if the rack is subject to vibration. -7-

10 SYSTEM CONNECTIONS Basic System Shown below is a typical connection scenario. Video Monitor Camera (VIDEO OUT) (VIDEO IN) WJ-DR200 OUT B VIDEO IN A S-VIDEO VIDEO OUT S-VIDEO POWER 120V AC 60 Hz 38W VIDEO OUT 1V [ p-p ] 75Ω Manufactured by Matushita Communication Industrial Co. Ltd Yokohama Japan FOR COMMERCIAL USE ONLY AUDIO OUT IN Made In Japan PARALELL SER. NO. CONTROL SERIAL CONTROL 6ZA00001 (Sensor) LED MONITOR GND SENSOR IN ALARM IN ALARM RESET IN SERIES REC IN TIME ADJUST IN GND ALARM OUT ALARM RECOVER OUT ALARM REC REC DISC BUZZER OUT SYSTEM ERROR OUT THERMAL ERROR OUT TIME ADJUST OUT SERIES REC OUT CAMERA SW OUT OUTPUT LEVEL H L (Alarm) Requirements for alarm and sensor input are as follows: SIGNAL GND CAUTION - FOR CONTINUED PROTECTION AGAINST FIRE HAZARD REPLACE ONLY WITH SAME TYPE FUSE ATTENTION - AFIN D' ASSURER UNE PROTECTION PERMANENTE CONTRE LES RISQUES D' INCENDIE REPLACER UNIQUEMENT PAR UN FUSIBLE DE MEME TYPE Cautions: Noise may appear in the monitor image and the audio may be interrupted under the following circumstances: Faulty camera synchronization, causing large frequency deviations between individual cameras Picture experiencing abrupt changes in brightness Faulty timing in switching input and recording of video signals (for example, a sequential switcher is not used for the camera switching output of the disc recorder, or switching is out of synchronization due to an alarm condition) Open collector output or no-voltage make contact The voltage between Ground and Alarm Input or Sensor Input when the circuit closes must be 0 to 0.2 V. The polarities can be changed by setting the SIGNAL TYPE parameter in the Alarm Recording menu. Notes: Recording of freeze pictures from VCR playback is not provided as a function. Recording is possible, but the results may not be satisfactory depending on the type of VCR used. When the Disc Recorder is connected to several cameras, for example through a multiplexer, all camera inputs must be synchronized to obtain proper images. Refer all connection work to qualified service personnel or system installers. Connection with Video Multiplexer 120V AC 60Hz 125V 4 A POWER ON OFF Example: Connection with Video Multiplexer WJ-FS616 Note: Refer connection with a Video Multiplexer other than the WJ-FS616 to qualified service personnel or system installers. WJ-DR200 System Setup WJ-DR200 Setup Menu VIDEO INPUT MULTI SHOT (MODE *) TIME LAPSE (MODE *) MANUAL REC ALARM SERIAL SETUP Item VIDEO INPUT CAMERA INPUT CAPTURE RATE SIGNAL TYPE Parameter COMPOSITE *1 S *1 A (CAMERA ID ON) 0.1 sec. or more RS-232C (VCR mode) *3 Default Setting COMPOSITE COMPOSITE A (CAMERA ID OFF) 0.20 sec. RS-232C -8-

11 WJ-DR200 VIDEO IN B A OUT VIDEO OUT POWER 120V AC 60 Hz 38W VIDEO OUT 1V [ p-p ] 75Ω Manufactured by Matushita Communication Industrial Co. Ltd Yokohama Japan FOR COMMERCIAL USE ONLY Made In Japan PARALELL SER. NO. 6ZA00001 CONTROL LED MONITOR GND SENSOR IN ALARM IN ALARM RESET IN SERIES REC IN TIME ADJUST IN GND ALARM OUT ALARM RECOVER OUT ALARM REC REC DISC BUZZER OUT SYSTEM ERROR OUT THERMAL ERROR OUT TIME ADJUST OUT SERIES REC OUT CAUTION - FOR CONTINUED PROTECTION AGAINST FIRE HAZARD REPLACE ONLY WITH SAME TYPE FUSE ATTENTION - AFIN D' ASSURER UNE PROTECTION PERMANENTE CONTRE LES RISQUES D' INCENDIE REPLACER UNIQUEMENT PAR UN FUSIBLE DE MEME TYPE 125V 4 A POWER ON Alarm Output Level Selector OUTPUT LEVEL H S-VIDEO AUDIO OUT IN SERIAL CONTROL OUTPUT LEVEL H L OFF H L S-VIDEO CAMERA SW OUT SIGNAL GND 120V AC 60Hz BNC Connector Pin Plug WJ-FS616 A B A B G ND G ND T R CAMERA IN CAMERA OUT WJ-FS616 Setup Menu SYSTEM SETUP 2/2 WJ-FS616 SETUP MENU REC MODE SETUP SYSTEM SETUP 1/2 ALARM SETUP RS SYSTEM SETUP 2/2 LINE TERM. SELECT OFF ON 2 4 WJ-FS616 System Setup CAMERA SW IN GENLOCK IN (VS) Item VCR IN SELECT REC/MULTI 2 SEQ TIMING-MLT ALM SCHEDULE ALM OUTPUT DUR DYNAMIC REC ALM REC MODE RS-232C MODE SPOT REC OUT PLAY IN MUL TISCREEN VCR CONTROL OUT I N VIDEO S [VIDEO VIDEO S [VIDEO VIDEO S [VIDEO RS [232C OUT DATA ALARM/REMOTE TERM. OFF ON Parameter VIDEO *1 S-VIDEO *1 IN SIGNAL GND REMOTE OUT SW1: Recording Output SW1 OFF VIDEO VIDEO Default REC OUTPUT MODE 9 (EXT1 or EXT4) *3 REC OUTPUT MODE 0 INT (TIME-AJD) INT (TIME-ADJ) ON OFF EXT *5 2 SEC ON *4 OFF MODE 9 MODE 0 VCR *2 VCR *1. Select VIDEO or S-VIDEO according to the connection. VIDEO: Select this parameter when the BNC connector is used for the connection. S-VIDEO: Select this parameter when the S- VIDEO connector is used for the connection. Monitoring the playback picture from the MULTISCREEN OUT connector or the SPOT connector is not available. *2. Connect only when WJ-DR200 is controlled by Video Multiplexer WJ-FS616. (Refer connection of the cable to qualified service personnel or system installers.) You need to set the communication parameters (DATA BIT, PARITY, etc.) on both the WJ-DR200 and the WJ-FS616. *3. This value applies to EXT 1. For EXT 4, set the parameter to 0.20 sec. or more. *4. Set this parameter to change the recording rate automatically when an alarm signal is received. *5. Set the recording time when alarm time lapse recording is required. -9-

12 Terminal Board The Terminal Board has the following functions. Make connections to these terminals as needed for operating your system. GND terminal is common ground for all terminals. GND SENSOR IN ALARM IN ALARM RESET IN Input Terminals SERIES REC IN TIME ADJUST IN GND ALARM OUT ALARM RECOVER OUT ALARM REC LED MONITOR REC DISC BUZZER OUT SYSTEM ERROR OUT THERMAL ERROR OUT TIME ADJUST OUT SERIES REC OUT SENSOR IN: Connects the input signal to start recording in Alarm Recording mode. (In Time Lapse mode, recording is enabled while this signal is input.) The ALARM indicator on the front panel of the Disc Recorder does not light in response to this recording input. (Any alarm output functions are disabled.) ALARM IN: Connects the input signal to start recording in Alarm Recording mode. (In Time Lapse mode, recording is enabled while this signal is input.) The Alarm indicator on the front panel of the Disc Recorder lights in response to this recording input. The buzzer sounds if the buzzer function was selected in the Setup menu. ALARM RESET IN: Connects the alarm and/or buzzer reset input when an alarm has been activated. SERIES REC IN: Connects an input signal to enable recording on two series-connected Disc Recorders. TIME ADJUST IN: Connects a time adjust input from an external source to synchronize the Disc Recorder s internal clock. When this input is detected, the time is adjusted to an accuracy of ±30 seconds. Output Terminals ALARM OUT: Sends an alarm signal in response to an alarm input. ALARM RECOVER OUT: Sends an alarm recover signal in response to the alarm reset signal received when the ALARM RESET button is pressed, or when recording in Alarm Recording mode is terminated. ALARM REC: Outputs an alarm recording signal while the Disc Recorder is operated in Alarm Recording mode. REC: Outputs an image recording signal while the Disc Recorder is recording pictures. The signal is interlocked with lighting of the REC indicator on the Disc Recorder s front panel DISC: Sends a signal when DVD-RAM disc space is running low. The signal s output parameters can be changed from the Setup menu. BUZZER OUT: Outputs a buzzer signal interlocked with the Disc Recorder s buzzer. SYSTEM ERROR OUT: Outputs an error signal when a fatal system error occurs in the Disc Recorder. THERMAL ERROR OUT: Outputs a signal when a temperature rise is detected in the Disc Recorder. TIME ADJUST OUT: Sends a time adjust signal used to slave the internal clocks of connected equipment to that of the Disc Recorder. Output as a 1-second pulse every day at 9:00 AM. SERIES REC OUT: Outputs a signal that enables recording on two series-connected Disc Recorders.

13 External Remote Control Parallel Control Port Connect an external remote control switch to the PARALLEL CONTROL port on the rear of the Disc Recorder as shown below. This enables remote control of the Disc Recorder in the same way as with the control buttons on the recorder s front panel Pin No Designation Ground Ground ALARM REC STANDBY UP STOP SET UP/ESC LOCK INDEX LEFT SET PLAY RIGHT PAUSE Pin No Designation FIND REC FORMAT DOWN OPEN/CLOSE FORMAT + PLAY BACK SELECT Not Used REVERSE PLAY ALARM RESET Not Used Ground -11-

14 Serial Control Port Connect a personal computer to the SERIAL CONTROL port on the rear of the Disc Recorder. This port conforms both with the RS-232C and RS-485 standard and permits remote control of the Disc Recorder or storing of video data to a personal computer Pin No. Designation 1 FG 2 TxD 3 RxD 4 RTS 5 CTS 6 DSR 7 SG 8 DCD 12 T(B) 17 R(B) 18 R(A) 20 DTR 23 T(A) INPUT/OUTPUT out in out in in in out in in out out Function Frame Ground Transmit Data Receive Data Request to Send Clear to Send Data Set Ready Signal Ground Data Carrier Detect Transmit Data (RS-485) Receive Data (RS-485) Receive Data (RS-485) Data Terminal Ready Transmit Data (RS-485) -12-

15 Series Recording Connection The WJ-DR200 can be set up for automatic serial recording by connecting a second recorder to its Terminal Board. Series Recording 1 (Alternate Alarm Recording) Connect the terminals on the Terminal Boards of the MASTER and SLAVE recorder as shown below. Connect the required video and audio input to both recorders. This will enable recording alarms alternately on the MASTER and on the SLAVE recorder. When there is no more recording space on the disc of the MASTER recorder, alarm recording switches to the SLAVE recorder. WJ-DR200 MASTER Recorder WJ-DR200 SLAVE Recorder GND SENSOR IN ALARM IN ALARM RESET IN SERIES REC IN TIME ADJUST IN GND ALARM OUT ALARM RECOVER OUT ALARM REC LED MONITOR REC DISC BUZZER OUT SYSTEM ERROR OUT THERMAL ERROR OUT TIME ADJUST OUT SERIES REC OUT GND SENSOR IN ALARM IN ALARM RESET IN Series Recording 2 (Alternate Time Lapse Recording) Connect the terminals on the Terminal Boards of the MASTER and SLAVE Recorder as shown below. When there is no more recording space on the disc of the MASTER recorder, time lapse recording switches to the SLAVE recorder. For uninterrupted recording, the disc of the MASTER recorder can be exchanged while recording is switched to the SLAVE recorder. (Up to 16 recorders including the MASTER recorder can be connected to record sequentially.) (Auxiliary Alarm Recording) An auxiliary record is made on the SLAVE recorder when a second alarm signal is received while the MASTER recorder is recording. This function is not available while the MASTER recorder is in an operating mode other than Alarm Recording (playback, search, etc.). Connect the required video and audio input to both recorders. For sensor input, connect the SENSOR IN instead of the ALARM IN terminals. SERIES REC IN TIME ADJUST IN GND ALARM OUT ALARM RECOVER OUT ALARM REC LED MONITOR WJ-DR200 MASTER Recorder WJ-DR200 SLAVE Recorder REC DISC BUZZER OUT SYSTEM ERROR OUT THERMAL ERROR OUT TIME ADJUST OUT SERIES REC OUT GND SENSOR IN ALARM IN ALARM RESET IN SERIES REC IN TIME ADJUST IN GND ALARM OUT ALARM RECOVER OUT ALARM REC LED MONITOR REC DISC BUZZER OUT SYSTEM ERROR OUT THERMAL ERROR OUT TIME ADJUST OUT SERIES REC OUT GND SENSOR IN ALARM IN ALARM RESET IN SERIES REC IN TIME ADJUST IN GND ALARM OUT ALARM RECOVER OUT ALARM REC LED MONITOR REC DISC BUZZER OUT SYSTEM ERROR OUT THERMAL ERROR OUT TIME ADJUST OUT SERIES REC OUT Connection for Alternate Time Lapse Recording -13-

16 SETUP PROCEDURES The Setup Menu provides a way for controlling functions not available through direct input. Displaying the SETUP MENU 1. Confirm that the camera and peripherals are connected correctly and securely. 2. Turn on the power switches of all system components. 3. Press the SET UP/ESC button of the Disc Recorder for about 2 seconds or more. The MAIN menu appears on the monitor screen as shown below. MAIN SET UP DISABLE SYSTEM * REC MODE MODE1 * MODE2 * ALARM RECORD * SEARCH/PLAY * SYSTEM INFO * Panasonic AV Disc Recorder V1.0R00 The following buttons are valid in the setup menu: SET UP/ESC UP : Moves the cursor upward. DOWN : Moves the cursor downward. LEFT : Moves the cursor to the left, or selects the mode or parameter. RIGHT : Moves the cursor to the right, or selects the mode or parameter. SET: Executes the selections and displays a submenu for an item with the (*) mark. SET UP/ESC: Executes the currently selected setting and returns to the previous setup menu. ( ): Selects the next mode or parameter. (+): Selects the previous mode or parameter. SET PLAY MODE 1 ALL PLAY BACK SELECT T/L MODE FORMAT + In the MAIN menu, press the SET UP/ESC button for about 2 seconds to apply the setting and exit the setup mode. Note: If alarm is activated during the setup operation, the setup menu disappears and the display returns to the normal picture. Any settings previously made take effect, even if the SET UP/ESC button was not pressed. -14-

17 MAIN Menu As shown below, the MAIN menu has seven main submenus: Set Up, System, Recording Mode 1, Recording Mode 2, Alarm Recording, Search/Play, and System Information. Six of these sub menus (System, Record Mode 1, Record Mode 2, Alarm Record, Search/Play and System Information) are further divided into additional submenus. MAIN Menu SET UP SET UP PASSWORD Page 16 SYSTEM RECORDING MODE 1 / 2 ALARM RECORDING SEARCH / PLAY SYSTEM INFORMATION CLOCK SET START UP STATUS SERIAL PORT SET UP VIDEO INPUT STATUS DISPLAY ALARM DISPLAY DISPLAY POSITION SERIES RECORD SERIES RECORD OUTPUT DISC LED FUNCTION BUZZER VIDEO PIXEL VIDEO QUALITY AUDIO RECORD CAPTURE MODE ENDLESS RECORD SIGNAL TYPE ALARM RECOVER FUNCTION ALARM TIMER DURATION ALARM BUZZER ALARM LABEL SENSOR LABEL DELAY TIME PROGRAM TIMER ON FIRST RECORD SKIP NUMBER RECORD SEARCH DATA THUMBNAIL PLAY PLAY MODE PLAY BACK RATE Page 16 Page 19 Page 26 Page 28 Page

18 SET UP Menu This menu lets you change the setup or register an up to 8-character password that will allow you access to the setup menu. MAIN SET UP ENABLE SYSTEM * REC MODE MODE1 * MODE2 * ALARM RECORD * SEARCH/PLAY * SYSTEM INFO * SYSTEM CLOCK * AUG :00 START UP STATUS MANUAL SERIAL SET UP * VIDEO INPUT * STATUS DISPLAY ON ALARM DISPLAY ON DISPLAY POSITION * SERIES REC MASTER SERIES REC OUT CLOSE DISC LED FUNCTION FULL BUZZER ON To select an item or parameter in the SYSTEM menu: Panasonic AV Disc Recorder V1.0R00 1. Move the cursor to the SET UP parameter in the MAIN Menu by pressing the or 2. Select ENABLE or PASSWORD by pressing the or The default setting is DISABLE. 3. Select ENABLE for making changes in the setup menu, or select PASSWORD for registering a password. Refer to Password Setup on page 31 for details. System Menu MAIN SET UP ENABLE SYSTEM * REC MODE MODE1 * MODE2 * ALARM RECORD * SEARCH/PLAY * SYSTEM INFO * Panasonic AV Disc Recorder V1.0R00 1. Move the cursor to the desired item or parameter by pressing the or 2. Press the or button to select the desired parameter. 3. Press the SET button to execute the selection or display a submenu for an item with the (*) mark. 4. Press the SET UP/ESC button to return to the MAIN menu, if desired. Clock Setup This item lets you set the current time and date. 1. Move the cursor to CLOCK in the SYSTEM menu by pressing the or button, then press the SET button to move the cursor to the editing area. 2. Move the cursor to the area you want to edit by pressing the or button, then select the month or number by pressing the (+) or ( ) Notes: Valid years are from 1998 to Set the last two digits for the year. For the year 2000, set 00. Set two digits for the hours (military time). 3. After finishing the setting, press the SET UP/ESC button to move the cursor to CLOCK. Note: The date and time are updated when the SET UP/ESC button is pressed. Select SYSTEM from the MAIN menu by pressing the or button, then press the SET The SYS- TEM menu appears on the monitor screen. As shown below, the SYSTEM menu allows access to 11 items. Start Up Status Setup This item lets you select the start-up mode of the Disc Recorder when the power is turned on. 1. Move the cursor to the START UP STATUS parameter in the SYSTEM menu by pressing the or -16-

19 2. Select the desired mode by pressing the or MANUAL: Selects manual recording mode. ALARM REC: Selects Alarm Recording mode. DISC AND ALARM REC: Selects Alarm Recording mode if a formatted disc is loaded. The default setting is MANUAL. 5. Select one of the interface modes shown below by pressing the or RS-232C, RS-232C (VCR mode) or RS-485 The default setting is RS-232C. 6. Move the cursor to the BAUD RATE parameter by pressing the or Note: It is recommended to select the modes shown below for normal usage. Select ALARM REC in the menu if the Alarm Recording mode is used frequently. MANUAL or ALARM REC mode can also be selected by pressing the ALARM REC STAND- BY button on the control panel of the recorder. Select DISC AND ALARM REC in the menu if the disc is exchanged each time after the Disc Recorder is powered up. The recorder automatically selects Alarm Record mode if a formatted disc is loaded. Serial Port Setup This item lets you set the parameters for communication between the SERIAL CONTROL port of the recorder and a PC when the Disc Recorder is remote controlled externally. 1. Move the cursor to SERIAL SET UP in the SYSTEM menu by pressing the or button, then press the SET The SERIAL SET UP menu shown below appears on the monitor screen. SERIAL SET UP PORT NUMBER 01 SIGNAL TYPE RS-232C BAUD RATE 9600 SET UP INFO START BIT 1 DATA BIT 8 PARITY CHECK NONE STOP BIT 1 Xon/Xoff NOT USE CIRCUIT SYSTEM HALF DUPLEX 7. Select one of the baud rates shown below by pressing the or 2 400, 4 800, 9 600, , , , The default setting is Press the SET UP/ESC button to return to the SYS- TEM menu. Video Input Setup This item lets you select the type of video input from the input connectors located on the rear of the Disc Recorder. 1. Move the cursor to VIDEO INPUT in the SYSTEM menu by pressing the or button, then press the SET The VIDEO INPUT menu shown below appears on the monitor screen. VIDEO INPUT VIDEO INPUT COMPOSITE CAMERA INPUT A(CAMERA ID OFF) CAMERA TYPE COLOR INPUT CHECK - 2. Move the cursor to the VIDEO INPUT parameter by pressing the or 2. Move the cursor to the PORT NUMBER parameter by pressing the or 3. Select the desired port number (01 to 16) by pressing the or button to identify the Disc Recorder when multiple recorders are connected in the system. The default setting is Move the cursor to the SIGNAL TYPE parameter by pressing the or 3. Select either COMPOSITE or S input by pressing the or COMPOSITE: Selects composite input for VIDEO IN A and B S: Selects the S-video input terminal. The default setting is COMPOSITE. 4. Move the cursor to the CAMERA INPUT parameter by pressing the or 5. Select the desired input and recording method by pressing the or -17-

20 A (CAMERA ID ON): Records only input A with multiplexed Camera ID signals. Use this parameter when the Disc Recorder is connected to a Video Multiplexer. You can select camera images in playback mode. The video pixel number (resolution) is fixed at 720 * 240. A (CAMERA ID OFF): Records only input A without multiplexed Camera ID signals. A+B (CAMERA ID OFF): Records input A and B without multiplexed Camera ID signals. Use this parameter when two cameras are connected to the Disc Recorder. Note: When two recording inputs are selected, audio recording is disabled in Multi Shot and Time Lapse Recording mode. The default setting is A (CAMERA ID OFF). 6. Move the cursor to the CAMERA TYPE parameter by pressing the or 7. Select either COLOR or B/W depending on the connected camera by pressing the or COLOR: Select this mode when a color camera is connected for input. B/W: Select this mode when a black and white camera is connected for input. The default setting is COLOR. 8. Move the cursor to the INPUT CHECK parameter by pressing the or 9. Press the or button to display the video selected with this parameter. This function is available only when the CAMERA INPUT parameter is set to A+B (CAMERA ID OFF) in this menu. 10. Press the SET UP/ESC button to return to the SYS- TEM menu. Status Display Setup This item lets you enable or disable status display or embedded display on the monitor screen. 1. Move the cursor to the STATUS DISPLAY parameter in the SYSTEM menu by pressing the or EMBEDDED: Enables time and date display only in recording mode and status display in playback mode. The default setting is ON. Alarm Display Setup This item lets you enable or disable alarm display on the monitor screen. 1. Move the cursor to the ALARM DISPLAY parameter in the SYSTEM menu by pressing the or 2. Select either ON or OFF by pressing the or ON: Enables alarm display on the monitor screen. OFF: Disables alarm display on the monitor screen The default setting is ON. Display Position Setup This item lets you select the positions where the alarm and status displays are placed on the monitor screen. 1. Move the cursor to DISPLAY POSITION in the SYS- TEM menu by pressing the or button, then press the SET The position setup menu shown below appears on the monitor screen. PRESS SET_UP/ESC KEY =MOVE UP =MOVE DOWN RECORD-# STATUS YY-MM-DD HH:MM:SS WARNING LABEL 2. Move the display position by pressing the or button, then press the SET UP/ESC button to execute the selection and return to the SYSTEM menu. 2. Select the desired mode by pressing the or ON: Enables status display on the monitor screen. OFF: Enables status display for two seconds on the monitor screen every time the status changes. -18-

21 Series Recording Setup This item lets you designate the master and the slave recorder when more than one Disc Recorder is used for series recording. 1. Move the cursor to the SERIES REC parameter in the SYSTEM menu by pressing the or 2. Select either MASTER or SLAVE by pressing the or MASTER: Designates a master recorder. SLAVE 1-15: Designates a slave recorder. Set the SLAVE 1 parameter for the second recorder. In Alternate Time Lapse Recording, you can record in sequence on up to 16 connected recorders. When three or more recorders are connected, set SLAVE 2 for the the third recorder, SLAVE 3 for the fourth, and so on up to SLAVE 15. The SLAVE 2-15 recorders are activated in numerical sequence. The default setting is MASTER. Series Recording Output Setup This item lets you set the signal type for the SERIES REC OUT terminal on the Terminal Board located on the rear of the Disc Recorder. 1. Move the cursor to the SERIES REC OUT parameter in the SYSTEM menu by pressing the or 2. Select either OPEN or CLOSE by pressing the or OPEN: CLOSE: Supplies the series recording output signal when the Disc Recorder is not in recording mode. Select this parameter for Alternate Alarm Recording (page 37). Supplies the series recording output signal when the Disc Recorder is in recording mode. Select this parameter for Alternate Time Lapse Recording (page 37). The default setting is CLOSE. 1. Move the cursor to the DISC LED FUNCTION parameter in the SYSTEM menu by pressing the or 2. Select either SPACE or FULL by pressing the or SPACE: Signal is output when disc space is running low (interlocks the signal with the DISC indicator on the Disc Recorder s front panel). See page 3. FULL: Signal is output when the disc is full. The default setting is FULL. Buzzer Setup This item lets you enable or disable the buzzer sound accompanying operation of the Disc Recorder s buttons. 1. Move the cursor to the BUZZER parameter in the SYSTEM menu by pressing the or 2. Select either ON or OFF by pressing the or ON: Enables buzzer. OFF: Disables buzzer. The default setting is ON. Recording Mode Menu This menu lets you set the recording mode for recording on the DVD-RAM disk. Select MODE 1 or MODE 2 and set up the items as shown below. MODE 1: This is the normal recording mode. Make sure to set up all items. MODE 2: Available with Program Recording only. (See pagees 27 and 38.) MAIN SET UP ENABLE SYSTEM * REC MODE MODE1 * MODE2 * ALARM RECORD * SEARCH/PLAY * SYSTEM INFO * Disc LED Function Setup This item lets you specify the conditions for output of the signal from the DISC LED MONITOR terminal on the Terminal Board located on the rear of the Disc Recorder. See page 10. Panasonic AV Disc Recorder V1.0R00 In the MAIN menu, move the cursor to the REC MODE parameter and select MODE 1 or MODE 2 by pressing the or button, then press the SET -19-

22 The REC MODE 1 or REC MODE 2 menu shown below appears on the monitor screen. VIDEO PIXEL VIDEO QUALITY AUDIO RECORD CAPTURE MODE ENDLESS REC MODE1 720*480/3DIM ON FINE OFF SINGLE SHOT OFF 2. Select the desired mode by pressing the or FINE: For enhanced sharpness NORMAL: For normal picture quality ROUGH: For lower picture quality The default setting is FINE. Audio Recording Setup This item lets you enable or disable audio recording. Audio recording is available depending on the selected recording mode as shown below. Recording start Recording end To change a parameter in the REC MODE menu: 1. Move the cursor to the desired item parameter by pressing the or 2. Select the desired parameter by pressing the or 3. Press the SET UP/ESC button to return to the MAIN menu, if desired. Video Pixels (Resolution) Setup This item lets you select the pixel number (number of horizontal x vertical picture elements) or resolution of the video picture. 1. Move the cursor to the VIDEO PIXEL parameter in the REC MODE menu by pressing the or 2. Select the desired mode by pressing the or 720 * 480/3DIM ON: High resolution none-blur picture. 720 * 480/3DIM OFF: High resolution picture 720 * 240: Lower resolution, but higher number of frames. The default setting is 720 * 480/3DIM ON. The parameter is fixed at 720 * 240 when the CAM- ERA INPUT parameter in the VIDEO INPUT menu is set to A (CAMERA ID ON). Video Quality (Compression Rate) Setup This item lets you set the quality of the video picture by selecting a compression rate. 1. Move the cursor to the VIDEO QUALITY parameter in the REC MODE menu by pressing the or -20- Multi Shot Time Lapse Recording (A) Single Shot Recording (A) Single Shot Recording (A+B) 1st shot A A B 2nd shot Last shot Continuous recording 4-second recording 4-second recording Audio recording is disabled in Multi Shot and Time Lapse Recording mode when the CAMERA INPUT parameter in the VIDEO INPUT menu is set to A+B. 1. Move the cursor to the AUDIO RECORD parameter in the REC MODE menu by pressing the or 2. Select either ON or OFF by pressing the or ON: Enables audio recording. OFF: Disables audio recording. The default setting is ON. Capture Mode Setup This item lets you select the mode for recording on the disc. 1. Move the cursor to the CAPTURE MODE parameter in the REC MODE menu by pressing the or 2. Select the desired mode by pressing the or SINGLE SHOT: For Single Shot recording. MULTI SHOT * : For Multi Shot recording. TIME LAPSE * : For Time Lapse recording. The default setting is SINGLE SHOT.

23 If you set the CAPTURE MODE parameter to MULTI SHOT or TIME LAPSE, make the necessary settings in the respective submenus shown on the following pages. Refer to the Multi Shot menu on page 21 or Time Lapse menu on page 22 for details. Endless Recording Setup This item lets you enable or disable uninterrupted recording when the disc space is used up. This function conforms to REC MODE 1 and is not available in REC MODE Move the cursor to the ENDLESS parameter in the REC MODE menu by pressing the or 2. Select either ON or OFF by pressing the or ON: Continues recording when the disc is full by overwriting the oldest data. OFF: Stops recording when the disc is full. The default setting is OFF. 1. Multi Shot Recording Setup This menu lets you make the necessary settings for Multi Shot Recording. 1. Move the cursor to the CAPTURE MODE parameter in the REC MODE menu by pressing the or 2. Select MULTI SHOT * by pressing the or button, then press the SET The MULTI SHOT menu shown below appears on the monitor screen. MULTI SHOT(MODE1) CAPTURE RATE 0.20 sec RECORD FRAMES 2 ( 0.4sec) PRE/POST FRAMES 0 /2 REC PATTERN - SENSOR REC SAME AS ALARM PRE/POST FRAMES - POST REC PATTERN - Capture Rate This item lets you specify the interval (seconds) for recording of multiple freeze pictures. 1. Move the cursor to the CAPTURE RATE parameter in the MULTI SHOT menu by pressing the or 2. Select the desired interval by pressing the or The following intervals are available depending on the selected pixel number. 720 * 480: 0.07, 0.10, 0.17, 0.20, 0.33, 0.50, 1.0, 2.0, * 240: 0.03, 0.07, 0.10, 0.17, 0.20, 0.33, 0.50, 1.0, 2.0, 3.0 The default setting is 0.20 sec. Recording Frames This item lets you select the number of frames that are recorded as freeze pictures on the disc. The maximum number of frames varies depending on the selected capture rate as shown below. Maximum number of Multi Shots Pixel number 720 x 480 AUDIO ON AUDIO OFF FINE NORMAL ROUGH FINE NORMAL ROUGH Pixel number 720 x 240 AUDIO ON AUDIO OFF FINE NORMAL ROUGH FINE NORMAL ROUGH Move the cursor to the parameters by pressing the or button, then select the desired mode by pressing or 1. Move the cursor to the RECORD FRAME parameter in the MULTI SHOT menu by pressing the or 2. Select the desired number of frames by pressing the or -21- The default setting is 2.

24 Pre/Post Frames This item lets you specify the number of pre-frames. A pre-frame is a frame recorded during standby for manual recording or prior to input of the alarm signal in alarm recording. A post-frame is a frame recorded after the REC button was pressed in manual recording or after input of the alarm signal in alarm recording. 2. Select either pattern by pressing the or SAME AS ALARM: Same recording pattern as for alarm activation DIFF FROM ALARM: Different recording pattern than for alarm activation The default setting is SAME AS ALARM. 1. Move the cursor to the PRE/POST FRAMES parameter in the MULTI SHOT menu by pressing the or 2. Select the desired number of pre-frames by pressing the or Subtracting the number of pre-frames from this total gives you the number of recorded post-frames. The default setting is 0. Recording Pattern When the CAMERA INPUT parameter in the VIDEO INPUT menu is set to A+B (CAMERA ID OFF), this item lets you select recording of pre and post-frames from input A and/or B. 1. Move the cursor to the REC PATTERN parameter in the MULTI SHOT menu by pressing the or 2. Select the desired recording input by pressing the or button as shown below. Pre Frame Quantity Zero More then one Parameter AA AB BB AA/BB AA/AB BB/AA BB/AB AB/AA AB/BB AB/AB Pre Frame Recorded A A B B A and B A and B A and B Post Frame Recorded A A and B B B A and B A A and B A B A and B 3. If you select DIFF FROM ALARM in step 2 above, you need to change the following parameters. Pre/Post-Frames This item lets you select the number of pre and post-frames recorded when there is sensor input from the SENSOR IN terminal. The maximum number of pre and post-frames is set with the PRE/POST FRAMES parameter above. 1. Move the cursor to the PRE/POST FRAMES parameter in the MULTI SHOT menu by pressing the or 2. Select the number of pre and post-frames to be recorded by pressing the or Post-Frame Recording Pattern This item is available only if the CAMERA INPUT parameter in the VIDEO INPUT menu is set to A+B (CAMERA ID OFF). It lets you select recording of pre and post-frames from input A and/or B when there is sensor input from the SENSOR IN terminal. 1. Move the cursor to the POST REC PATTERN parameter in the MULTI SHOT menu by pressing the or 2. Select the desired recording input for post-frames by pressing the or AA: BB: AB: Records input A for post-frames. Records input B for post-frames. Records input A and B for post-frames. Sensor Recording This item lets you select whether to record sensor input from the SENSOR IN terminal on the rear of the Disc Recorder according to the same pattern as set for alarm recording or according to a different pattern. 1. Move the cursor to the SENSOR REC parameter in the MULTI SHOT menu by pressing the or 2. Time Lapse Recording Menu This menu lets you set up the details for Time Lapse Recording. Note: Manual Alarm Recording, Record Partition and Auto Start are not available in MODE Move the cursor to the CAPTURE MODE parameter in the REC MODE menu by pressing the or -22-

25 2. Select TIME LAPSE * by pressing the or button, then press the SET The TIME LAPSE menu shown below appears on the monitor screen. Recording Pattern When the CAMERA INPUT parameter in the VIDEO INPUT menu is set to A+B (CAMERA ID OFF), this item lets you select recording of pre and postframes from input A and/or B. TIME LAPSE(MODE*) CAPTURE RATE 0.20 sec (RECORD TIME 1h35m) PRE FRAMES 0 REC PATTERN - SENSOR REC SAME AS ALARM PRE FRAMES - POST REC PATTERN - MANUAL REC ALARM OFF RECORD PARTITION 80 AUTO START OFF 3. Move the cursor to the parameters by pressing the or button, then select the desired mode by pressing the or Capture Rate This item lets you specify the interval (seconds) for recording of multiple freeze pictures. 1. Move the cursor to the CAPTURE RATE parameter in the TIME LAPSE menu by pressing the or 2. Select the desired interval by pressing the or The following intervals are available depending on the selected pixel number. 720 * 480: 0.07, 0.10, 0.17, 0.20, 0.33, 0.50, 1.0, 2.0, * 240: 0.03, 0.07, 0.10, 0.17, 0.20, 0.33, 0.50, 1.0, 2.0, 30.0 The default setting is 0.20 sec. Pre Frames This item lets you select the number of pre-frames recorded in standby for manual recording or prior to alarm input in alarm recording mode. 1. Move the cursor to the PRE FRAMES parameter in the TIME LAPSE menu by pressing the or 2. Select the desired number of frames by pressing the or The default setting is Move the cursor to the REC PATTERN parameter in the TIME LAPSE menu by pressing the or 2. Select the desired recording input by pressing the or button as shown below. Pre Frame Quantity Zero More then one Parameter AA AB BB AA/BB AA/AB BB/AA BB/AB AB/AA AB/BB AB/AB Sensor Record Pre Frame Recorded A A B B A and B A and B A and B Post Frame Recorded A A and B B B A and B A A and B A B A and B This item lets you select whether to record sensor input from the SENSOR IN terminal on the rear of the Disc Recorder according to the same pattern as set for alarm recording or according to a different pattern. 1. Move the cursor to the SENSOR REC parameter in the TIME LAPSE menu by pressing the or 2. Select either pattern by pressing the or SAME AS ALARM: Same recording pattern as for alarm activation DIFF FROM ALARM: Different recording pattern than for alarm activation The default setting is SAME AS ALARM. 3. If you select DIFF FROM ALARM in step 2 above, you need to change the following parameters. Pre Frames This item lets you select the number of pre-frames recorded when there is sensor input from the SEN- SOR IN terminal. The maximum number of pre-frames is set with the PRE FRAMES parameter above. 1. Move the cursor to the PRE FRAMES parameter in the TIME LAPSE menu by pressing the or 2. Select the number of pre-frames to be recorded by pressing the or