Ni - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
|
|
- Maude Richardson
- 5 years ago
- Views:
Transcription
1 50S Installation Instructions SF-SING MRGN QUIPMN! IMPFGURDS! WHN USING RI QUIPMN, SI SF PRUIONS SHOUD WS FOOWD, INUDING H FOOWING: RD ND FOOW SF INSRUIONS 1. o prevent high voltage from being present on red & yellow output leads prior to installation, inverter connector must be open. Do not join inverter connector until installation is complete and power is supplied to the emergency ballast. 2. his product is for use with one 17 W through 215 W (2-8 ) or two 17 W through 40 W (2-4 ) single pin or bipin fluorescent lamps, including standard, energy saving, HO, VHO, circline, U-shaped and rapid-start (4-pin) long compact fluorescent lamps. 3. Make sure all connections are in accordance with the National lectrical ode or anadian lectrical ode and any local regulations. 4. o reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter connector of the emergency ballast before servicing. 5. his emergency ballast is for factory or field installation in either the ballast channel or on top of the fixture. 6. his product is suitable for damp locations where the ambient temperature is 0 minimum, +50 maximum. Product is also suitable for installation in sealed and gasketed fixtures. Product is not suitable for heated air outlets and wet or hazardous locations. 7. n unswitched power source is required. (120 or 277 V, 60Hz) 8. Do not install near gas or electric heaters. 9. Do not attempt to service the battery. sealed, no-maintenance battery is used that is not field replaceable. ontact the manufacturer for information on service. 10. he use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 11. Do not use this product for other than intended use. 12. Servicing should be performed by qualified service personnel. SV HS INSRUIONS NR/ Ni - d HIS PRODU ONINS RHRG NI-DMIUM R. HR MUS RD DISPOSD OF PROPR. 08/04/11 Philips mergency ighting Division of Philips lectronics North merica orporation 236 Mt. Pleasant Rd. ollierville, N US ech Support Fax
2 INSION WRNING: O PRVN HIGH VOG FROM ING PRSN ON & OW OUPU DS PRI O INSION, INVRR ONN MUS OPN. DO NO JOIN INVRR ONN UNI INSION IS OMPND POWR IS SUPPID O H MRGN S. NO: Make sure the necessary branch circuit wiring is available. n unswitched source of power is required. he emergency ballast must be fed from the same branch circuit as the ballast. SP #1 INSING H MRGN S > Disconnect power from the fixture. Remove the ballast channel cover and install the emergency ballast either in the ballast channel or on top of the fixture.* Remote mounting distance must be less than half the maximum remote mounting distance for the ballast. onsult ballast manufacturer before remote installation. > Depending on the type of fixture in use install emergency ballast using one of the methods illustrated below. INSID Inside S allast hannel HNN INSID Inside SRIP Strip Fixture FIXUR ON On OP op OF of Fixture FIXUR * For installation on top of the fixture, wire bundle covers (RM-60) may be required by state or local codes. hese covers are available from the manufacturer as an accessory kit and must be ordered separately. all your local distributor or the factory for complete information. SP #2 INSING H S > Refer to the illustrations above and install the test switch through the ballast channel cover of a troffer or through the side of a strip fixture. Fixture est utton Hex Nut est Switch > Drill a 1/2 hole and install the switch as shown. > Wire the test switch so that it removes power from both the emergency ballast and the ballast at the same time. (see wiring diagrams) Push to est eads Hex Nut SP #3 INSING H IGH > Install the IGH as shown in the illustration on the following page so that it will be visible after the fixture is installed. 2
3 SP #4 WIRING H MRGN S > Determine the type of ballast installed in the fixture. > Select the appropriate wiring diagram on back to connect the emergency ballast to the ballast and lamp(s). Make electrical connections in accordance with the National lectrical ode, anadian lectrical ode and any local regulations. > o disable audible alarm, cut red/white wire loop. P NDS. > fter installation is complete, supply power to the emergency ballast and join the inverter connector. It is normal for the indicator light to remain off for a few minutes on inital start-up, as the battery voltage rises to normal range. Refer to rubleshooting Guide if this condition persists. > t this point, power should be connected to both the ballast and the emergency ballast, and the harging Indicator ight should illuminate indicating the battery is charging. > short-term discharge test may be conducted after the emergency ballast has been charging for one hour. harge for 24 hours before conducting a long-term discharge test. Refer to OPRION. > In a readily visible location, attach the label UION - his Unit Has More han One Power onnection Point. o Reduce he Risk Of lectric Shock, Disconnect oth he ranch ircuit-reakers Or Fuses nd mergency Power Supplies efore Servicing. IGH INSION ROFFR S FIXUR SRIP S FIXUR Fixture Fixture harging Indicator ight harging Indicator ight Violet (+) Violet (+) rown ( ) rown ( ) 1/2" White ushing 1/2" Punch 5/8" lack ushing 1/2" White ushing 5/8" lack ushing OPRION During normal operation, power is applied and the self-testing emergency ballast charges the battery. onnecting the (red and white) battery connector wires enables the emergency circuit, and supplies power to the control/monitor circuit and charging indicator light. he self-testing emergency ballast continually monitors the charging current and battery voltage, comparing them to preset limits. Should the unit detect an unusual current or voltage condition, the indicator light will flash and the internal audible alarm will sound. When power fails, the self-testing emergency ballast automatically switches to emergency mode, keeping either one or two lamps illuminated at a reduced lumen output for a minimum of 90 minutes. When power is restored, the self-testing emergency ballast returns to charging mode and delays ballast operation for approximately three seconds to prevent false tripping of ballast (end-of-lamp life) shutdown circuits. SF-SING OPRION his unit contains a control/monitor circuit that automatically performs a 30-second discharge test every 30 days, and a full 90-minute discharge test once a year. During routine testing, the self-testing emergency ballast simulates an power failure causing the unit to automatically switch to emergency mode. he unit will monitor the operation of the lamps, battery voltage, discharge current, and emergency duration. If the emergency system functions properly, then the unit will return to normal mode. Should the unit detect any problems, the indicator light will flash continually and the audible alarm will sound four times every 30 seconds until the condition has been corrected or the unit passes the next test. o reset a failure indication, push and hold the test switch for a minimum of 15 seconds. If the condition has not been corrected by the next scheduled test, the unit will once again detect the failure and signal the failure indicator. o cancel a test, turn the wall switch ON (or OFF if switch is already on), wait five seconds, then turn it OFF (ON). 3
4 MINNN his self-testing emergency ballast automatically performs required routine testing. Results are reported to maintenance personnel via the indicator light and audible alarm. Note: If optional audible alarm is disabled, maintenance personnel should periodically check the indicator light. If the indicator light is flashing, go through all steps of roubleshooting Guide. ROUSHOOING GUID SUS S IGH ight on steady, not flashing Flashing 1/2 Second Intervals Flashing 1/2 Second Intervals UDI RM PROM ONN No beeping None Unit is Operating orrectly. eeping 1/2 Second Intervals eeping 4 times every 30 seconds ine voltage; incorrect installation attery voltage is outside limits. Failed scheduled self-test heck line voltage. For 120 V use black as hot; for 277 V use orange as hot wire lead. et battery charge. If after an hour failure is still indicated, see action below. 1. heck to make sure lamps are good (operational and specified for self-testing emergency ballast) and in place. 2. heck to see if brown connector is properly used. (See able 1.) 3. heck that fixture wiring is in accordance with proper wiring diagram. 4. llow unit to charge for 24 hours. Perform manual test. If flashing/beeping continue, emergency ballast should be replaced. ny other erroneous status indications orrupted chip memory Open inverter connector (red and white wires) and push manual test switch for 15 seconds minimum, then reconnect battery connector. Failure Status will be reset when the unit passes: he next automatic test, or manual test exceeding 15 seconds, or n actual power failure exceeding 15 seconds. NO: It is normal for the indicator light to remain off for a few minutes on initial start-up or after a very long power outage (discharge), as the battery voltage rises to normal range. Refer to the roubleshooting Guide if this condition persists. 4
5 50S WIRING DIGRMS he following diagrams are typical schematics only. May be used with other ballasts. onsult the factory for other wiring diagrams. mergency allast and allast must be fed from the SM RNH IRUI. IMPN X: RFR O 1 RGRDING brown connector able 1 MP (DIMR) 8,9,10,12 (1, 1¼, 1½ ) ONG OMP WIN/QUD/ RIP WIN/ QUDRUP WIN-U OMP 2D S P Single or ipin 4-PIN (2G11) 4-PIN (G24q,GX24q) 4-PIN (GR10q) WG (ength) W (2'-4') W (5' -8') W NO. of MPS (MRGN- MOD) ONN 1 OSD 2 OPN 1 OPN 1 OSD 2 OPN W 1 OSD W 1 OSD 2 OPN 42 W 1 OSD W 1 OSD 2 OPN 55 W 1 OPN FIG WIRING DIGRM for 1-MP emergency operation SR SS INSR SS ON (1) MP SR S FIG ON (1) MP INSR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Refer to able 1 before connecting MP 1 MP SR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Refer to able 1 before connecting MP 1 MP INSN SR S FIG WO (2) MP SR S FIG D WO (2) MP INSR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Refer to able 1 before connecting MP 1 (MRGN ) MP 2 2 MP SR S OW OW S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Refer to able 1 before connecting MP 1 (MRGN) MP 2 2 MP INSR SR S FIG HR (3) MP SR S FIG F HR (3) MP INSR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Refer to able 1 before connecting MP 1 (MRGN) U/ U/ OW MP 2 OW 3 MP MP 3 SR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Refer to able 1 before connecting MP 1 (MRGN) MP 2 3 MP INSN MP 3 SR S FIG G S FOUR (4) MP SR S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ 4 MP SR S WRNING: Refer to able 1 before connecting OW OW U/ U/ MP 1 MP 2 MP 3 MP 4 (MRGN) FIG H S FOUR (4) MP INSR S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ 4 MP INSN SR S WRNING: Refer to able 1 before connecting OW OW MP 1 MP 2 MP 3 MP 4 (MRGN) 5
6 FIG I MRGN S ND S MUS FD FROM H SM RNH IRUI PI SHMIS ON. M USD WIH OHR SS. ONSU H F F OHR WIRING DIGRMS. WIRING DIGRM for 1-MP emergency operation ON (1) MP OMP SR S FIG J WO (2) MP OMP SR S / W INVRR ONN M OW S UZZR / / S VIO R G IGH 120V (P UNUSD D) NG 277V U/ / WRNING: Refer to able 1 before connecting MP 1 MP SR S / W INVRR ONN M OW S UZZR / / S VIO R G IGH 120V (P UNUSD D) NG 277V U/ / 2 MP SR S WRNING: Refer to able 1 before connecting OW OW MP 1 ( MRGN) MP 2 FIG WO (2) MP SR SP DIMMING S S / INVRR ONN M UZZR / S VIO R G IGH 120V (P UNUSD D) NG 277V / S1 S2 OW / U/ WRNING: Refer to able 1 before connecting MP 1 (MRGN ) MP 2 2 MP SR OW SP OW DIMMING S H / D MUS ONN O H D OF H SP-DIMMING S SSOID WIH H MRGN S ON. ONNIONS O OHR SS FIXURS OUD RSU IN NM OPRION ND US PRODU DMG. WIRING DIGRMS for 2-MP emergency operation (2-4, W lamps only) wo-lamp emergency operation is not possible with all ballasts. onsult the factory for any ballast other than those shown. FIG WO (2) MP SR S FIG M WO (2) MP INSR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Do NO connect brown connector MP 1 MP 2 2 MP OW SR OW S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Do NO connect brown connector MP 1 MP 2 2 MP INSR SR S FIG N HR (3) MP SR S FIG O HR (3) MP INSR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Do NO connect brown connector MP 1 (MRGN) U/ U/ OW MP 2 (MRGN) OW 3 MP MP 3 SR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: DO NO connect brown connector MP 1 (MRGN) MP 2 (MRGN) 3 MP INSN MP 3 SR S FIG P FOUR (4) MP SR S FIG Q FOUR (4) MP INSR S S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: DO NO connect brown connector MP 1 (MRGN) OW OW U/ MP 2 (MRGN) U/ 4 MP MP 3 SR S MP 4 S W INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V / M R G OW / U/ WRNING: Do NO connect brown connector MP 1 (MRGN) MP 2 (MRGN) 4 MP OW INSN MP 3 SR S OW MP 4 FIG R WO (2) OMP MP SR S / W INVRR ONN M OW S UZZR / / S VIO R G IGH 120V (P UNUSD D) NG 277V U/ / WRNING: Do NO connect brown connector MP 1 OW OW MP 2 2 MP SR S 6
7 WIRING DIGRMS for mergency-only fixtures FIG S WO (2) MPS WIHOU S (17W-40W) FIG ON (1) MP WIHOU S (16W-215W) S (P) / INVRR ONN UZZR / S VIO IGH 120V (P UNUSD D) NG 277V M R G N S OW / U/ WRNING: DO NO connect brown connector MP 1 (P) (P) MP 2 S (P) / INVRR ONN UZZR / S VIO IGH 120V (P UNUSD D) NG 277V M R G N S OW / U/ WRNING: Refer to able 1 before connecting MP (P) (P) (P) / (P) / FIG U ON (1) 4-PIN OMP MP WIHOU S (16W-55W) FIG V WO (2) 4-PIN OMP MPS WIHOU S (16W-39W) S (P) / INVRR ONN M OW UZZR / / S VIO R G IGH 120V (P UNUSD D) NG 277V U/ WRNING: Refer to able 1 before connecting MP (P) (P) S (P) INVRR ONN UZZR S IGH (P UNUSD D) / / VIO 120V NG 277V M R G OW / U/ WRNING: Do NO connect brown connector MP MP (P) (P) (P) / (P) / NO: Installation of this self-testing fluorescent emergency ballast is different from standard models. he emergency ballast must interrupt the switched or unswitched hot lead feeding the ballast. efore beginning installation, consult these wiring diagrams. 7
Ni - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
B74CST Installation Instructions SLF-ING MRGNC ING QUIPMNT! IMPTANT SAFGUARDS! WHN USING LCTRICAL QUIPMNT, BASIC SAFT PRCAUTIONS SHOULD ALWAS B FOLLOWD, INCLUDING TH FOLLOWING: RAD AND FOLLOW ALL SAFT
More informationBdl60u Fluorescent Emergency Ballast
A Division Of Philips Electronics North America Corporation One- or two-lamp emergency; Universal input voltage: 120 through 277 V, 50 or 60 Hz; Replaces B60U Bdl60u Fluorescent Emergency Ballast Product
More informationI-320 SERIES AC EMERGENCY LIGHTING EQUIPMENT
P.O. BOX 84 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 74-2837 www.iotaengineering.com INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be
More informationSAVE THESE INSTRUCTIONS INSTALLATION INSTRUCTIONS EMERGENCY FLUORESCENT BATTERY PACK MODEL PS300, PS600, PS1400
INSTALLATION INSTRUCTIONS EMERGENCY FLUORESCENT BATTERY PACK MODEL PS300, PS600, PS1400 CAUTION: For safety and proper operation, read and follow instructions carefully before installation. FIELD INSTALLABLE
More informationLUCE 1 TL. specifications: internal. specifications: external. ordering logic. builder. Job/Location:
LUCE 1 TL indoor / damp Job/Location: Contractor: Prepared By: Job Type: Date: The LUCE-1TL thinline emergency ballast is designed to provide emergency illumination to existing or new fluorescent luminaires.
More informationSERVICE BY QUALIFIED PERSONNEL ONLY
Installation Instructions Automatic Load Control Relay For Emergency Lighting! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
More informationGTD20A Installation Instructions BRANCH CIRCUIT TRANSFER SWITCH/LIGHTING CONTROL DEVICE
Installation Instructions BRANCH CIRCUIT TRANSFER SWITCH/ CONTROL DEVICE UL 1008-BCELTS UL 924-Switch Bypass! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS
More informationLubrication cycle IP Enclosure Rating. 110 VAC, 220/230 VAC (50/60 Hz) Alarm Fault Relay Contacts. IP-55 (Liquid tight connector)
SMAC Controller Industrial Lubrication Systems Operation The SMAC Controller is a multi-purpose programmable controller used with industrial lubrication systems. Controller settings are saved whenever
More informationBACKUP BATTERY INSTALLATION INSTRUCTIONS
www.tiltlights.com BACKUP INSTRUCTIONS A Lauren International Company www.laurenillumination.com 855 440 8458 LdPE7-2014 SELf-TESTINg EmERgENCY LEd driver RATINGS: Input: 100-277 VAC 50 or 60 Hz Output:
More informationINSTALLATION INSTRUCTIONS - POWER SENTRY CONTROL POWER SENTRY CONTROL UNIT PSBCEB2 INSTALLATION INSTRUCTIONS
POWER SENTRY CONTROL UNIT PSBCEB2 INSTALLATION INSTRUCTIONS READ AND FOLLOW THESE INSTRUCTIONS BEFORE INSTALLATION TO ENSURE PROPER AND SAFE OPERATION SAVE THESE INSTRUCTIONS READ AND FOLLOW ALL SAFETY
More informationINSTALLATION INSTRUCTIONS - PS1055LCP & PS1555LCP LED EMERGENCY DRIVER PS1055LCP & PS1555LCP
LED EMERGENCY DRIVER PS1055LCP & PS1555LCP INSTALLATION INSTRUCTIONS READ AND FOLLOW THESE INSTRUCTIONS BEFORE INSTALLATION TO ENSURE PROPER AND SAFE OPERATION SAVE THESE INSTRUCTIONS LED EMERGENCY DRIVER
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. NXM Series - Survive-All. Emergency Light Unit
Emergency Light Unit IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. Do not
More informationILB-CP TBTS A MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED
P.O. BOX 11846 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 741-2837 www.iotaengineering.com INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More informationINSTRUCTION MANUAL IMPORTANT SAFEGUARDS. When using electrical equipment, basic safety precautions should always be followed, including the following:
ILB-CP20-HE-A TBTS HIGH EFFICIENCY EMERGENCY LIGHTING EQUIPMENT FOR LED INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed, including
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. HZM-Series-Class I, Div 2 Battery Unit. Instalation instructions
HZM-Series-Class I, Div 2 Battery Unit HZM-Series-Class I, Div 2 Battery Unit Instalation instructions IMPORTANT SAFEGUARDS 1 4 5 6 7 13 When using electrical equipment, basic safety precautions should
More informationILB-CP TBTS B MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED Patented. See iotaengineering.com/patents for more details
P.O. BOX 11846 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 741-2837 www.iotaengineering.com INSTRUCTION MANUAL IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always
More informationTSLED STAIRWELL INSTALLATION INSTRUCTIONS
TSLED STAIRWELL INSTALLATI INSTRUCTIS TSLED- 2FT TSLED - 4FT IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with
More informationR8845U Universal Switching Relay
Universal Switching Relay PPLIION he Universal Switching Relay provides intermediate switching of line- and low-voltage devices from a line- or low-voltage controller. he may be used to replace several
More informationILB-CP TBTS A MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED
P.O. BOX 11846 TUCSON, AZ 85734 (520) 294-3292 FAX (520) 741-2837 www.iotaengineering.com ILB-CP TBTS A MOUNTING DESIGN EMERGENCY LIGHTING EQUIPMENT FOR LED Patented. See iotaengineering.com/patents for
More informationLED Emergency Battery Backup Installation Instructions Ordering Code: EB23UQ
LED Emergency Battery Backup Installation Instructions Ordering Code: EB23UQ PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION SAFETY INSTRUCTIONS AND WARNINGS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY
More informationCompatible with most electronic AC ballasts Maintenance-free, long-life, high temperature Ni-Cad battery Durable, heavy duty steel housing 5-year
Compatible with most electronic AC ballasts Maintenance-free, long-life, high temperature Ni-Cad battery Durable, heavy duty steel housing 5-year warranty 1300 Lumens JWEB-1300 The VEM1300DV fluorescent
More informationIMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS. 3LERHZ Series Class I, Div 2 Combo Unit. Installation instructions
3LERHZ Series Class I, Div 2 Combo Unit Installation instructions 3LERHZ Series Class I, Div 2 Combo Unit IMPORTANT SAFEGUARDS 1 3 When using electrical equipment, basic safety precautions should always
More informationLED Emergency Battery Backup
LED Emergency Battery Backup Installation Instructions Ordering Code: PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION: TROFFER INSTALLATION STRIP INSTALLATION INTRODUCTION & TABLE OF CONTENTS Ordering
More informationMODEL RLY-DIM-D INSTALLATION INSTRUCTIONS
MODEL RLY-DIM-D INSTALLATION INSTRUCTIONS IMPORTANT SAFEFGUARDS WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED. THESE INCLUDE: READ AND FOLLOW ALL SAFETY INSTRUCTIONS
More informationRAZOR RZR SERIES DIE CAST ALUMINUM LED EXIT SIGNS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS
RAZOR RZR SERIES DIE CAST ALUMINUM LED EXIT SIGNS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Flow Lighting QuickLED NEW FIXTURE 2x4 2x2 1x4 Corporate 1240 Texan Trail, Suite 102 Grapevine, TX 76051 (817)435-8484 Office www.flowledlighting.com READ AND FOLLOW ALL SAFETY
More informationNURSECALL 800E MK3 SYSTEM INSTRUCTIONS BASIC WIRING
NURS 800 MK SYSTM NSTRUTONS S WRN MPORTNT The Social Services register Rest omes and ealth authorities register Nursing omes. Please check your system complies. WRN o not use solid core cable as it breaks
More informationMODEL LUT-ATS-D (EPC-D-F-ATS) INSTALLATION ! IMPORTANT SAFEGUARDS!
MODEL LUT-ATS-D (EPC-D-F-ATS) INSTALLATI! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ AND FOLLOW ALL SAFETY INSTRUCTIS
More informationDIGITAL LIGHT CONTROLLER
DIGITAL LIGHT CONTROLLER Manual - Model UD 0900 Modular lighting controller for 20 HPS or MH lamps Reading this manual will help you better understand the functions of your device and its potential. Keep
More informationMicroprocessor Intruder Alarm System User Guide
9 8 0 0 Microprocessor Intruder larm System User Guide SNTRONI LTD Glossary of Terms ccess ode utomatic Signalling Device ell-walk Test hime (optional) Day State Deferred Set Duress Entry Time Exit Time
More informationUltraLITE Model ELU Centralized Emergency Lighting Inverter 4.2 KW- 5 KW
12/23/16 Rev 9 UltraLITE Model ELU General Specification 4.2 KW to 5 KW UltraLITE Model ELU Centralized Emergency Lighting Inverter 4.2 KW- 5 KW 1.0 General General Specification This specification describes
More informationCDL8 LED Architectural
Project: Type: Model# CDL8 LED Architectural PRODUCT DESCRIPTION Retrofit Down lights The Luminoso 8 inch Commercial LED Downlight is damp rated, and suitable for 1-277V Input equipped with fire-rated
More informationMANUFACTURED IN THE UK
The Mini-Max range of energy efficient bulkhead fittings are manufactured with a polycarbonate base and diffuser. Together with a poured gasket the Mini-Max leads vandal-resistant IP65 technology. With
More information15" (38.1 CM) ELECTRIC COOKTOP INSTALLATION INSTRUCTIONS INSTRUCTIONS D INSTALLATION DE TABLE DE CUISSON ÉLECTRIQUE DE 15" (38,1 CM)
15" (38.1 M) LTRI OOKTOP INSTLLTION INSTRUTIONS INSTRUTIONS INSTLLTION TL UISSON ÉLTRIQU 15" (38,1 M) Table of ontents/table des matières OOKTOP STY...2 INSTLLTION RQUIRMNTS...3 Tools and Parts...3 Location
More informationUser Operation Manual
APPROVED BY: JBJ PRESCIENT III FIRE ALARM & GAS EXTINGUISHING CONTROL PANEL User Operation Manual PAGE 1 of 6 1 CONTENTS 1. FIRE - GENERAL... 3 2. FIRE - ZONES 1 OR 2 - AUTOMATIC MODE... 3 3. FIRE - ZONES
More informationWARNING WARNING WARNING
Installation guide Philips Evoase LE Retrofit KIT G1 2 x4 and 2 x2 FILURE TO FOLLOW TI-IESE INSTRUCTIONS N S M RESULT IN SERIOUS INJUR OR SIGNIFICNT PROPERT MGE. For your protection, carefully read these
More informationSecurit 7 Alarm Panel
Securit 7 larm Panel Stock No. 436-881 ntroduction The Securit 7 is a microprocessor controlled intruder alarm panel. t features seven zones of which five are programmable and two dedicated to entry/exit
More information1 General Description
1 General Description LED Tube Light adopts the new type LED as the light source, using the standard TB tube's end caps, makes it easy to install and replace the traditional fluorescent lamp. The TRF-51894
More informationMODEL EPC-D-F-ATS INSTALLATION INSTRUCTIONS ! IMPORTANT SAFEGUARDS!
MODEL EPC-D-F-ATS INSTALLATI INSTRUCTIS! IMPORTANT SAFEGUARDS! WHEN USING ELECTRICAL EQUIPMENT, BASIC SAFETY PRECAUTIS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ AND FOLLOW ALL SAFETY INSTRUCTIS
More informationNYC Approved Product Series
NYC Approved Product Series ON THE PROJECT, ON THE SHELF, ON THE JOB NYC APPROVED Table of Contents NYC Approved LED Exit & Combo Series P. 2 NYC Approved LED Battery Series P. 3 NYC Approved Total Edge
More informationInstallation guide. Philips EvoKit LED 2x4 and 2x2
Installation guide Philips EvoKit LED 2x4 and 2x2 This installation guide is only valid for the following Philips EvoKit models: Products 2x4 EvoKit 2x4 P 36L 36W 835 2 0-0 7 G2 EvoKit 2x4 P 36L 36W 840
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 26 ELECTRICAL
SECTION 265100 - INTERIOR LIGHTING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Interior lighting fixtures, lamps, and ballasts. 2. Emergency lighting units. 3. Exit signs. 4.
More informationHIGH BAY APPLICATIONS
STAIRWELLS The IIS Inverter can operate multiple fixtures in a building s stairwell and can be wired to bypass dimmers or occupancy sensors...keeping your egress corridors lit without sacrificing your
More informationPremier Hazard STC Instructions
PREMIER HAZARD Ltd Bessingby Industrial Estate Bridlington YO16 4SJ Tel: +44 (0) 113 239 1111 Fax: +44 (0) 113 239 1131 www.premierhazard.co.uk info@premierhazard.co.uk Premier Hazard STC Instructions
More information13.1 Anti Theft Alarm (ATA) Contents
13.1 nti Theft larm (T) Contents 13.1 Model 129 Page Diagnostics Technical Changes........................... 10/1 Function Test............................... 11/1 Diagnostic Trouble Code (DTC) Memory............
More informationINSTALLATION INSTRUCTIONS Low Ambient Kit NASA201LA, NASA401LA
INSTALLATION INSTRUTIONS Low Ambient Kit NASA201LA, NASA401LA These instructions must be read and understood completely before attempting installation. DANGER, WARNING, AUTION, and NOTE The signal words
More informationApplication Note. Using XPoint Wireless Devices with Emergency Lighting. 1 of 16
Using XPoint Wireless Devices with Emergency Lighting 1 of 16 Table of Contents Introduction...3 Application Summary...3 UL924 Standard Summary...4 ER Option - Normal Power Sensing Leads...4 ER Intended
More informationLeakSafe. solutions. WaterSwitch2. Installation Instructions
LeakSafe solutions TM WaterSwitch2 Installation Instructions WATERSWITCH2 COMPONENTS WaterSwitch2 Valve Control Extended Range Valve Driver Valve Water Flow Sensor Leak Detection tape available in 0.3M
More informationABS SECURITY ALARM INSTRUCTION MANUAL
ABS-1000+ SU AA SU AUA PA # 6130610 H ABS-1000+ SU AA AS H FW ASSS: (1pc.) A to Adaptor (n. - 120A, ut. - 15) (2pc.) emote ontroller W Battery (1pc.) Battery connection Wire (4pc.) Wall ounting Bracket
More informationOperation Manual. ParaBeam 400/200 Series. ParaBeam 400 Center Mount. ParaBeam 400 Pole-Op
Operation Manual ParaBeam 400/200 Series ParaBeam 400 Center Mount ParaBeam 400 Pole-Op Part No. 3100026 Rev D 01-04-2010 x ParaBeam Fixture Styles and Features ParaBeam Center Mount PAR-400S-120 ParaBeam
More informationInfrared Wall Mount Occupancy Sensor
LOS-WI LOS-WI-1 02.01.06 Infrared Wall Mount Occupancy Sensor The LOS-WI wall-mounted passive infrared sensor is used in spaces with pendant fixtures, ceiling fans, or high ceilings (more than 12 feet).
More informationTO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
Tech Sheet Do not discard AI Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. PECAUTIOS
More informationOWNER S MANUAL. High-Wall Fan Coil Unit CONTENTS
OWNER S MANUAL High-Wall Fan Coil Unit Page GENERAL 2,3 OPERATING MODES 2 REMOTE CONTROL 2 OPERATION 3-9 REMOTE CONTROL OPERATION 3 INDOOR UNIT DISPLAY 5 EMERGENCY OPERATION 5 PRESSING THE ON/OFF BUTTON
More informationInstallation Instructions
KSALA0201R22 KSALA0301410 Low--Ambient Pressure Switch Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY ONSIDERATIONS Improper installation, adjustment,
More informationPlatelet Agitator Operation Manual
Platelet gitator Operation Manual i.series and Horizon Series Model Group i.series Horizon Series Countertop PF15i, PF48i, PF96i (Version ) PF15h, PF48h, PF96h (Version ) Floor PF396i (Version ) - HELMER
More informationTO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
Tech Sheet Do not discard ANING Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. PECAUTIONS
More informationFire detection and alarm system Operating instructions
Fire detection and alarm system Operating instructions Operating instructions Table of Contents User responsibility - - - - - - - - - - - - 4 Daily - - - - - - - - - - - - - - - - - - - 4 Weekly - - -
More informationHARLOW ELECTRIC FIREPLACE
HRLOW ELECTRIC FIREPLCE MODEL NO. 064-3504-2 SSEMBLY INSTRUCTIONS Toll-free: 1-888-670-6684 IMPORTNT: Please read this manual carefully before beginning assembly of this product. Keep this manual for future
More informationTHINLINE TL2 SERIES INSTALLATION AND OPERATING INSTRUCTIONS
THINLINE 2.0 - TL2 SERIES DIE CAST ALUMINUM LED EXIT SIGNS INSTALLATION AND OPERATING INSTRUCTIONS IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed
More informationMatrix2000. User Guide - CPD Advanced Analog Fire Alarm Control Panel 4 24 Zones. Version: 2.0 Revision: 1
Matrix2000 User Guide - CPD Advanced Analog Fire Alarm Control Panel 4 24 s Version: 2.0 Revision: 1 IMPORTANT INFORMATION Limitation of liability It is mandatory, Matrix2000 panel to be installed in accordance
More informationK00364 Electronic Bin Thermostat
K00364 Electronic Bin Thermostat Installation Instructions This kit reduces overfill and condensation issues and can be used on any Manitowoc ice machine installed on an ice dispenser. Order kit number
More informationWL24000 Series Reflectorized Troffer Luminaries
WL24000 Series Reflectorized Troffer Luminaries DESCRIPTION WL SERIES TROFFER LUMINARIES combines a highly reflective specular reflector and an electronic ballast. These premium quality energy saving fixtures
More informationMANUAL. OEM (Unit) OZONE GENERATOR (100VA, 200VA and 300VA) INDEX
MANUAL OEM (Unit) OZONE GENERATOR (100VA, 200VA and 300VA) INDEX 1) Technical Specifications: (100VA, 200VA, 300VA) 2) Introduction 3) Construction 4) Operation and maintenance a) Operating Procedure b)
More informationTable of Contents/ Table des matières
30" (76.2 M) ND 36" (91.4 M) ELETRI INDUTION OOKTOP INSTLLTION INSTRUTIONS INSTRUTIONS D INSTLLTION DE L TLE DE UISSON ÉLETRIQUE À INDUTION DE 30" (76,2 M) ET DE 36" (91,4 M) OOKTOP SFETY... 2 INSTLLTION
More informationInstallation Instructions / User s Manual NAXA00101DB Communicating Daughter Board
Installation Instructions / User s Manual NAXA00101DB ommunicating Daughter Board The NAXA00101DB daughter board control allows for using 4 existing thermostat wires in an existing, finished home to communicate
More informationESRB and ESRN Installation & Safety Instructions
B1784 ESRB and ESRN Installation & Safety Instructions IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW
More informationCAUTION: ELECTRICAL HAZARD
R R Installation Guide 53DF50-HW hermostat System ypes Cool Only (single stage) Heat Pump (with electric heat) CAUION: ELECRICAL HAZARD Can cause electrical shock or equipment damage. Disconnect power
More informationPRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
Tech Sheet Do not discard AIG Electrical Shock Hazard Disconnect power before servicing. eplace all parts and panels before operating. Failure to do so can result in death or electrical shock. PECAUTIOS
More informationMSPA-MP METAPACK SERVICE MANUAL. Visual step-by-step guide to easily identify & correct technical problems! Gecko Electronics Inc.
MSPA-MP METAPACK SERVICE MANUAL Gecko Electronics Inc. Visual step-by-step guide to easily identify & correct technical problems! Table of Contents Power & Ground Check Tools and Parts 3 Electrical Wiring
More informationOperating instructions SENTRI4 Control panel based Fire detection and alarm system
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 30 32 Zones Healthy 15:45 Fault Power Fault System Fault SenTRI 4 Fire System Designed to EN54 Pt 2 & 4 Operating instructions
More informationElectrician Installation Manual EM-E Ceiling Fan
Electrician Installation Manual CEILING FAN MUST BE INSTALLED BY A LICENSED ELECTRICIAN (NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN) *Electricians are recommended to tick off all items on the
More informationTT /97. Features INSTALLATION INSTRUCTIONS. Horn. Lamps
TT-1023 1/97 INSTALLATION INSTRUCTIONS Original Issue Date: 2/94 Model: 6-2000 kw Market: Industrial Subject: Flush- or Surface-Mount Remote Annunciator Kits PA-293991 and PA-293991-SD The remote annunciator
More informationWARRANTY LED ECO PANEL.
ED ECO PANE www.trulygreensolutions.com ED ECO PANE 7 MODES AVAIABE IN 30W TO 75W EXPECTED IE OVER 50,000 HRS IES IES @ www.trulygreensolutions.com Compatible Emergency Battery Backup Available eatures
More informationFire Burglary Instruments Inc. XL-2G Gold Control/Communicator Installation Training Seminar Rev. 5/96
Fire Burglary Instruments Inc. XL-2G Gold Control/Communicator Installation Training Seminar Rev. 5/96 XL-2G Gold Product Overview 7 Zones (6 programmable + panic or keyswitch zone) Fast Loop Response
More informationAcross-the-Line SERIES MP300 Combined Manual and Automatic
Across-the-Line SERIES MP300 Combined Manual and Automatic Metron Fire Pump Controllers conform to the latest requirements of National Fire Protection Association s Standard for Centrifugal Fire Pumps
More informationTable of Contents/Table des matières COOKTOP SAFETY
30" (76.2 M) ELETRI INDUTION OOKTOP INSTLLTION INSTRUTIONS INSTRUTIONS D'INSTLLTION DE LTLEDEUISSON ÉLETRIQUE À INDUTION DE 30" (76,2 M) Table of ontents/table des matières OOKTOP SFETY... 1 INSTLLTION
More informationLED ECO PANEL.
Not all products are qualified on the DC QP. To view our DC qualified products, please consult the DC Qualified Products ist at www.designlights.org/qpl. ED ECO PANE www.trulygreensolutions.com ED ECO
More informationTROFFER RETROFIT KIT (TRK)
Not all products are qualified on the DLC QPL. To view our DLC qualified products, please consult the DLC Qualified Products List at www.designlights.org/qpl. TROFFER RETROFIT KIT (TRK) www.trulygreensolutions.com
More informationNational Warranty Line
CEILING FAN MUST BE INSTALLED BY A LICENSED ELECTRICIAN (NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN) *Electricians are recommended to tick off all items on the quick checklist and fill out their
More information1 x4 Dimmable LED RetroFits
1 x4 Dimmable LED RetroFits Installation Instructions Ordering Code: RF16UQT1XXCDL RF16UHT1XXDL RF32UQT1XXCDL RF32UHT1XXDL PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION OF THE FOLLOWING: 4 STRIP FIXTURES
More informationLED ECO PANEL.
Not all products are qualified on the DC QP. To view our DC qualified products, please consult the DC Qualified Products ist at www.designlights.org/qpl. ED ECO PANE www.trulygreensolutions.com ED ECO
More informationCONTROLS INSTRUCTIONS MANUAL ENGLISH
CONTROLS INSTRUCTIONS MANUAL ENGLISH Table of Contents 1. Introduction of the Innova Controls 3 1.1 Precautions 3 2. Operating Instructions 2.1 Quick Start 4 2.2 Direction of Use 5 2.2.1 Heater on 5 2.2.2
More informationARTEMIS Series of Low Occupancy LED Ceiling Mounted Fixtures (Including Stairwells) Installation & Operation Guide
Low Occupancy Fixture XL Stairwell Fixture XS 1 Please read these instructions carefully, and keep them for future reference. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions
More informationProduct Bulletin for Decora Rocker Slide Controls
Product Bulletin for Decora Rocker Slide Controls Decora Rocker Slide Controls Application Leviton Decora Rocker Slide s provide smooth, slide-action, full-range dimming for incandescent, dimmable LEDs,
More informationActivating the Test Mode. Test Mode Functionality
TECH SHEET - DO NOT DISCARD PAGE Timer (any cam input change will result in a beep) NOTE: Timer will advance during test. If any of the inputs do not result in a beep, proceed to the following component
More informationUniversal Dimmer N 528D01, 2 x 300VA, AC 230 V 5WG DB01
Gamma instabus Universal Dimmer N 528D01, 2 x 300VA, AC 230 V 5WG1 528-1DB01 Technical Product Information Universal Dimmer for switching or dimming of dimmable lamps Supports dimmable lamps including
More informationDKG 972. Gas Burner Safety Control. For 2-stage atmospheric gas burners
certified Qualitysystem ISO 9001 / EN 29001 Reg. Nr. 10529 Gas Burner Safety Control A Honeywell Company For 2-stage atmospheric gas burners Flame detection: - Ionisation probe - Infrared-flicker detector
More informationProduct Bulletin. Zenith Controls. Automatic Transfer Switch. ZTG Series. Fully Approved. Design and Construction Features
e G Zenith Controls Product ulletin ZTG Series utomatic Transfer Switch LD/LCD indicators for ease of viewing and long life Nonvolatile memory clock battery backup not required for standard switch operation
More informationTo operate the 5207 you can use either the built-in touchpad or the Model 5230 Remote Annunciator.
Section 5 Operation To operate the 5207 you can use either the built-in touchpad or the Model 5230 Remote Annunciator. Figure 5-1 Built-in Touchpad (Seven-Segment Display) Figure 5-2 Model 5230 Remote
More informationREMOTE CONTROL CAR ALARM SYSTEM
REMOTE CONTROL CAR ALARM SYSTEM Email: technicalsupport@stadiumcp.co.uk SPARKRITE SR90 REMOTE CAR ALARM SYSTEM INTRODUCTION The Sparkrite SR90 advanced remote control alarm system incorporates the latest
More informationCeiling PIR HS presence detector 1-10V, low temperature. PIR Sensor. IR Receiver. Light Level Sensor. Status LEDs. IR Receiver
Product Guide EBDHS-AD-LT30 Ceiling PIR HS presence detector 1-10V, low temperature Overview The EBDHS-AD-LT30 PIR (passive infrared) presence detector provides automatic control of lighting loads with
More information, ,
796-2028, 796-2021, 796-2025 Batten mount PIR detectors Overview This series of miniature PIR (passive infrared) presence detectors provide automatic control of lighting loads with optional manual control
More informationInstall Guide 3M-10 ENGLISH
Install uide 3M-10 ENLISH Install uide 3M-10 aution Tools Location To avoid electrical shock and to prevent damage to the furnace, air conditioner, and thermostat, disconnect the power supply before beginning
More informationSoft Start Series MP700 Solid State, Reduced Voltage
Metron Fire Pump Controls and Accessories Soft Start Series MP700 Solid State, Reduced Voltage Metron Fire Pump Controllers conform to the latest requirements of National Fire Protection Association s
More informationSERVICE MANUAL New Electronic Cold Platform 2005.
SERVICE MANUAL New Electronic Cold Platform 2005. All the parts included in this document are the property of Indesit Company S.p.A. All rights reserved. This document and the information it contains are
More informationD A R A - 4. Data Aire Relay Auto-Changeover
D A R A - 4 Data Aire Relay Auto-Changeover WARNING: If adding the DARA-4 panel to existing units that did not include a DARA-4 panel when originally purchased it will be necessary to add a relay or relays.
More informationDigital Marine Exhaust Temperature Alarm
Digital Marine Exhaust Temperature Alarm Model: SM007D/S INTRODUCTION COMPONENTS Marine water cooled exhaust systems are designed to withstand temperatures of up to about 120 C. However the exhaust gases
More informationSYSTEM 5000 USER MANUAL
SYSTEM 5000 USER MANUAL Table of Contents Section Page No 1 Introduction: -... 3 1.1 Procedure:... 3 1.2 Warnings and Cautions:... 3 2 User Control Levels:... 4 3 User Passwords:... 4 4 Controls and Displays:
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
Operating Manual MODELS RC554XP AND 554000 ORP/pH Digital Controller FEED ph ALERT FEED ORP ALERT F LOW ph MODE AUTO FEED ONCE SET LEVEL FEED TIME HI LOW ph CALIB ORP ph ORP IMPORTANT SAFETY INSTRUCTIONS
More information