Haywood County Animal Services Facilities

Transcription

1 Haywood County Animal Services Facilities July 22, 2016 Addendum #2: General: Storefront aluminum windows to be equal to Kawneer 8225T with screens at operable units. Finish to be selected from manufacturers standard colors. Sound proofing glazing to be 1 tempered consisting of 1 lite of laminated glass and 1 lite of tempered glass with ½ air space to occur at elevations G, H, M, & N and all doors in dog rooms 148, 151, 149, 152, & 153 Sun tunnels shown at Mezzanine A to go thru mezzanine to ceiling at main floor level. Specifications Cover Sheet: Change notice to read: property of Haywood County Division 8 Section Sectional Overhead Doors #7 C. Special Operators: Delete vehicle detector operation and card reader control Supply two remote controls for each door.

2 1. Revise sheet C1.0 to read: 2" IPS HDPE (2" I.D.), DR- 13.5, PE 4710, AWWA C906 water service line. 2. Eliminate proposed SMH#2 from C Change 59 Lf. of 8 PVC sanitary sewer line beneath Jones Cove Rd. to 6 PVC, SDR-35. Reference plan and profile on C Change 33 Lf., 18 dia. Steel casing to 12 dia. steel casing. Reference Profile on C Fire Hydrant Assembly, Gate Valves and Box are to be manufactured by Mueller Company. (Note added to sheet C2.0. Standard JSD details apply) General, informational revisions to the plan set include; - Ownership dividing line (JSD/Owner) shown on detail WL-16 - Text revision; replace Junaluska Utility Authority with Junaluska Sewer District.

3 Addendum #2 Project Name: Haywood County Animal Services Facilities Date: July 22, 2016 Project #: NOTICE TO ALL CONTRACTORS SUBMITTING BIDS FOR THIS WORK AND TO ALL PLAN HOLDERS: You are herby notified of the following changes, clarifications or modifications to the original Contract Documents, Drawings, and subsequent Addenda. This Addendum shall supersede the original Contract Documents, and any previous Addenda wherein it contradicts the same and shall take precedence over anything to the contrary therein. All other conditions remain unchanged. Clarifications / Revisions: Sheet A-7.0: 1BA-7.0 Kitchenette Revise W_3624 to W-3636 with bottom at 48 A.F.F Sheet A-7.0: 3/A-7.0 Break Revise W_3624 to W_3636 with bottom at 48 A.F.F Sheet A-7.0: 4A/A-7.0 Work Room - Revise the (2) leftmost B36 cabinets to UAB_36 cabinets at 2-10 height. Drop counter only over these cabinets. Revise leftmost W_3624 cabinet to a W_3636 with bottom at 48 A.F.F Sheet A-7.0: 6/A-7.0 Intake Exam Revise SB-24 cabinet to an SUAB-24 and drop counter only over this cabinet. Revise W_3624 to (1) W_1836 and (1) W_1824 with leftmost bottom at 48 A.F.F Sheet A-7.0: 7/A-7.0 Grooming - Change stainless steel sink base cabinet SB-38 to counter top height of Drop counter to 2-10 only at this cabinet. Revise leftmost W-3624 to W_3636 with bottom at 48 A.F.F Sheet A-7.0: 8/A-7.0 Interview Drop counter top at leftmost knee space to Revise leftmost W_3030 to W_3036 with bottom at 48 A.F.F Sheet A-7.0: 8B/A-7.0 Interview Admin Drop counter top at knee space down to Revise leftmost W_3030 to W_3036 with bottom at 48 A.F.F Sheet A-7.0: 9B/A-7.0 Food/Dish Drop stainless steel counter down to Extend wall brackets and add third shelf at 46 A.F.F. Move carts under counter to elevation 9A/A-7.0 and move Microwave to the left Sheet A-7.1: 5A/A-7.1 Laundry Drop right most section of stainless steel counter next to utility sink down to Extend wall brackets over sink and this section

4 of counter down and add a third shelf at 46 A.F.F Sheet A-7.1: 7A/A-7.1 Medical Change SB-36 to SUAB-36 and drop counter just over this cabinet to Revise rightmost W_3324 to W_3336 with bottom at 48 A.F.F Sheet A-7.1: 8A/A-7.1 Work Stations Revise W-3030 to W_3036 with bottom at 48 A.F.F Specs: Add following to spec section C. Under-Counter Warewashing Machines. 1. Basis-of-Design Product: Subject to compliance with requirements, provide Model Number SR24H by Hobart Corporation or comparable product. 2. Description: Hot water sanitizing dishwasher with single tank bottom. a. Capacity: 19 racks per hour. b. Booster Heater: 70 degree rise. c. Stainless steel front panel. d. Automatic Fill. e. Accessories: 1) Chemical sensing device. 2) Stainless steel side panels. 3) Pressure regulator valve. 4) Specs: Add Residential Appliances section , see attached. End of Addendum #2

5 HAYWOOD COUNTY ANIMAL SERVICES SECTION RESIDENTIAL APPLIANCES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Residential microwave. 2. Refrigeration appliances. 1.2 SUBMITTALS A. Product Data: For each type of product indicated. B. Samples: For each exposed product and for each color and texture. C. Product certificates. D. Operation and maintenance data. E. Warranties: Sample of special warranties. 1.3 QUALITY ASSURANCE A. Installer Qualifications: An employer of workers trained and approved by manufacturer for installation and maintenance of units required for this Project. 1.4 WARRANTY A. Special Warranties: Manufacturer's standard form in which manufacturer agrees to repair or replace residential appliances or components that fail in materials or workmanship within specified warranty period. 1. Warranty Period: One year from date of Substantial Completion. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Basis-of-Design Product: Subject to compliance with requirements, provide product indicated or comparable product by one of the following: July 22, 2016 SECTION

6 HAYWOOD COUNTY ANIMAL SERVICES 1. General Electric Company (GE). 2. LG Appliances. 3. Maytag; a division of Whirlpool Corporation. 4. Sub-Zero, Inc. 5. Whirlpool Corporation. 6. Broan-Nutone. 2.2 RESIDENTIAL APPLIANCES A. Microwave Oven: 1. Basis-of-Design Product: General Electric Profile PEB9159DJBB or a comparable product. 2. Oven: Standard features include the following: a. Oven Capacity: 1.5 cu. ft.. b. Oven Features: Digital control panel with timer display, turntable. c. Mounting: Undercabinet with built-in kit and countertop. d. Electrical Power: 1500 W. e. Oven Door: Counter-balanced, removable, finish with observation window. f. Exhaust Fan: Two -speed fan, vented to outside, 300 cfm. B. REFRIGERATION APPLIANCES 1. Refrigerator/Freezer at Staff Break Room and Multi-Purpose Room: Energy Star Rated with ice maker, 22-cu. ft. minimum. 2. Refrigerator/Freezer at Food Prep.: Energy Star Rated, freestanding, 18-cu. ft. minimum. 3. Under-counter Refrigerator: Energy Star Rated, freestanding, 4.8-cu. ft. minimum. a. Type 1: Under the counter, frost-free, one-door refrigerator with inside freezer compartment designed for installation under 36 countertop. b. Type 2: Equivalent ADA-compliant refrigerator to fit under 34 countertops at locations indicated on drawings. PART 3 - EXECUTION 3.1 INSTALLATION, GENERAL A. Built-in Equipment: Securely anchor units to supporting cabinets or countertops with concealed fasteners. Verify that clearances are adequate for proper functioning and that rough openings are completely concealed. July 22, 2016 SECTION

7 HAYWOOD COUNTY ANIMAL SERVICES B. Freestanding Equipment: Place units in final locations after finishes have been completed in each area. Verify that clearances are adequate to properly operate equipment. C. Range Anti-Tip Device: Install at each range according to manufacturer's written instructions. D. Utilities: See Divisions 22 and 26 for plumbing and electrical requirements. 3.2 FIELD QUALITY CONTROL A. Perform tests and inspections. 1. Manufacturer's Field Service: Engage a factory-authorized service representative to inspect components, assemblies, and equipment installations, including connections, and to assist in testing. B. Tests and Inspections: 1. Perform visual, mechanical, and electrical inspection and testing for each appliance according to manufacturers' written recommendations. Certify compliance with each manufacturer's appliance-performance parameters. 2. Leak Test: After installation, test for leaks. Repair leaks and retest until no leaks exist. 3. Operational Test: After installation, start units to confirm proper operation. 4. Test and adjust controls and safeties. Replace damaged and malfunctioning controls and components. C. Prepare test and inspection reports. END OF SECTION July 22, 2016 SECTION

8 Plumbing 1. Refer to Plumbing Specifications all above ground domestic water lines to be PEX with push on or compression banded fittings. Support spacing to be per manufacturer s specifications. Fire Protection 1. Refer to Fire Protection Drawing FP-1, Flow Test. Fire Hydrant flow test data is attached to this addendum. 2. Refer to specifications Section Automatic Fire Protection System. Delete reference to the Owner s Insurance Underwriter. All work to be in complete accordance with NC Department of Insurance (NC Building Code) requirements and NFPA 13. Electrical 1. Refer to Drawing E-3. Sprinkler hot box referenced is actually a vault which is located on Civil drawing C 1.0. Weatherproof receptacle specified is to be installed in the vault. 2. Refer to Drawing E-3 and Addendum #1. The 4 conduit to the road for service entrance referenced in the telephone/data riser is to be routed to Jones Cove Road and terminated at the location designated by the service provider. Contractor is to assume this location could occur at any point along the property line frontage on Jones Cove Road. 3. Refer to Specifications Section Fire Alarm System. Disregard reference to an existing fire alarm panel. The fire alarm panel is to be new as specified on the drawings and by addendum. 4. Clarification: Use of MC Cable is to be restricted to that specified on the drawings and in the specifications, Per Owner direction. 5. Refer to Drawing E-2. Wall-Mounted Occupancy Sensor (Sos) Switch to be similar to Leviton #ODSO-IDG, 120/277v rated, wired per mfg s recommendations. 6. Refer to Drawing E-2. The G fixtures shown in the Outside Flex Quarantine (x4) and the Outdoor Dog Adoption (x5) are to be a 4 linear surface mount with 3500 K color temperature, wet listing and dimming capabilities in lieu of the fixture shown. Use Failsafe #HVSL4-4-LD4-2STD-35-UNV-0 WL, or approved equal. Color by Architect. 7. Refer to Drawing E-4, Fire Alarm Symbol Schedule The Fire Alarm Panel is to be EST #IO-64. The Annunciator is to be EST #RLCD-C. Smoke Detectors to be SIGA-PS2. Horn Strobes (Weatherproof, outdoor) to be EST #WG4WF-HVMC. Visual Alarms to be G1-VM. 8. Refer to specification section attached for information on surge suppression. 9. Clarification on Electrical Alternates: a. Alternate #3 Provide Fire Alarm System manufactured by Edwards Systems Technologies (EST), Access Control System manufactured by Honeywell, and Security Camera System manufactured by Interlogix. b. Alternate #4 Fire Alarm, Access Control, and Security Camera Systems are to be furnished and installed by Haynes Technologies.

9 Reece, Noland & McElrath SECTION TRANSIENT-VOLTAGE SUPPRESSION FOR LOW-VOLTAGE ELECTRICAL POWER CIRCUITS PART 1 - GENERAL 1.1 SUMMARY A. This Section includes TVSSs for low-voltage power equipment. 1.2 SUBMITTALS A. Product Data: For each type of product indicated. Include rated capacities, operating weights, operating characteristics, furnished specialties, and accessories. B. Field quality-control test reports. C. Operation and Maintenance Data. 1.3 QUALITY ASSURANCE A. Source Limitations: Obtain suppression devices and accessories through one source from a single manufacturer. B. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, Article 100, by a testing agency acceptable to authorities having jurisdiction, and marked for intended use. C. Comply with IEEE C62.41, "IEEE Guide for Surge Voltages in Low Voltage AC Power Circuits," and test devices according to IEEE C62.45, "IEEE Guide on Surge Testing for Equipment Connected to Low-Voltage AC Power Circuits." D. Comply with NEMA LS 1, "Low Voltage Surge Protection Devices." E. Comply with UL 1283, "Electromagnetic Interference Filters," and UL 1449 (3 rd edition), "Transient Voltage Surge Suppressors." 1.4 PROJECT CONDITIONS A. Service Conditions: Rate surge protection devices for continuous operation under the following conditions, unless otherwise indicated: 1. Maximum Continuous Operating Voltage: Not less than 115 percent of nominal system operating voltage. 2. Operating Temperature: 30 to 120 deg F. 3. Humidity: 0 to 85 percent, noncondensing. 4. Altitude: Less than 20,000 feet above sea level. PART 2 - PRODUCTS 2.1 MANUFACTURERS A. Manufacturers: Subject to compliance with requirements, provide products by one of the following: 1. Advanced Protection Technologies, Inc. 2. Atlantic Scientific. 3. Current Technology, Inc. 4. Cutler-Hammer, Inc.; Eaton Corporation. 5. Entrelec International. 6. General Electric Company. 7. Innovative Technology, Inc. 8. Intermatic, Inc. 9. LEA International. 10. Leviton Mfg. Company Inc. 11. Liebert Corporation; a division of Emerson. 12. Northern Technologies, Inc. 13. Siemens Energy & Automation, Inc. 14. Square D; Schneider Electric. 15. Surge Suppression Incorporated. 16. Sutton Designs Inc. 17. Transtector Systems, Inc. 18. Tycor; Cutler-Hammer, Inc. 19. United Power Corporation. TRANSIENT-VOLTAGE SUPPRESSION FOR LOW-VOLTAGE ELECTRICAL POWER CIRCUITS

10 Reece, Noland & McElrath 20. Zero Surge Inc. 2.2 SERVICE ENTRANCE SUPPRESSORS A. Surge Protection Device Description: Non-modular, sine-wave-tracking type with the following features and accessories: 1. LED indicator lights for power and protection status. 2. Audible alarm, with silencing switch, to indicate when protection has failed. 3. Fuses, rated at 200-kA interrupting capacity. 4. Integral disconnect switch. 5. Redundant suppression circuits. 6. Surge-event operations counter. B. Peak Single-Impulse Surge Current Rating: [240] ka per phase. C. Connection Means: Permanently wired. D. Protection modes and UL 1449 suppressed voltage rating for grounded wye circuits with voltages of [208Y/120], 3-phase, 4-wire circuits shall be as follows: 1. Line to Neutral: [400 V for 208Y/120]. 2. Line to Ground: [400 V for 208Y/120]. 3. Neutral to Ground: [400 V for 208Y/120]. E. Protection modes and UL 1449 suppressed voltage rating for 240/120-V, single-phase, 3-wire circuits shall be as follows: 1. Line to Neutral: 400 V. 2. Line to Ground: 400 V. 3. Neutral to Ground: 400 V. F. Protection modes and UL 1449 suppressed voltage rating for 240/120-V, 3-phase, 4-wire circuits with high leg shall be as follows: 1. Line to Neutral: 400 V, 800 V from high leg. 2. Line to Ground: 400 V. 3. Neutral to Ground: 400 V. G. Protection modes and UL 1449 suppressed voltage rating for voltages of 240 or 480, 3-phase, 3- wire, delta circuits shall be as follows: 1. Line to Line: [1000 V for 240 V]. 2. Line to Ground: [1000 V for 240 V]. 2.3 PANELBOARD SUPPRESSORS A. Surge Protection Device Description: Non-modular, sine-wave-tracking type with the following features and accessories: 1. LED indicator lights for power and protection status. 2. Audible alarm, with silencing switch, to indicate when protection has failed. 3. Fuses, rated at 200-kA interrupting capacity. 4. Integral disconnect switch. 5. Redundant suppression circuits. 6. Surge-event operations counter. B. Peak Single-Impulse Surge Current Rating: [120] ka per phase. C. Protection modes and UL 1449 suppressed voltage rating for grounded wye circuits with voltages of [208Y/120], 3-phase, 4-wire circuits shall be as follows: 1. Line to Neutral: [400 V for 208Y/120]. 2. Line to Ground: [400 V for 208Y/120]. 3. Neutral to Ground: [400 V for 208Y/120]. D. Protection modes and UL 1449 suppressed voltage rating for 240/120-V, single-phase, 3-wire circuits shall be as follows: 1. Line to Neutral: 400 V. 2. Line to Ground: 400 V. 3. Neutral to Ground: 400 V. E. Protection modes and UL 1449 suppressed voltage rating for 240/120-V, 3-phase, 4-wire circuits with high leg shall be as follows: TRANSIENT-VOLTAGE SUPPRESSION FOR LOW-VOLTAGE ELECTRICAL POWER CIRCUITS

11 Reece, Noland & McElrath 1. Line to Neutral: 400 V, 800 V from high leg. 2. Line to Ground: 400 V. 3. Neutral to Ground: 400 V. F. Protection modes and UL 1449 suppressed voltage rating for voltages of 240 or 480, 3-phase, 3- wire, delta circuits shall be as follows: 1. Line to Line: [1000 V for 240 V]. 2. Line to Ground: [800 V for 240 V]. 2.4 SUPPRESSORS FOR ELECTRONIC-GRADE PANELBOARDS A. Surge Protection Device Description: Sine-wave-tracking type, panel-mounted design with the following features and accessories: 1. LED indicator lights for power and protection status. 2. Audible alarm, with silencing switch, to indicate when protection has failed. 3. Arrangement with wire connections to phase buses, neutral bus, and ground bus. B. Peak Single-Impulse Surge Current Rating: [120] ka per phase. C. Protection modes and UL 1449 suppressed voltage rating for grounded wye circuits with voltages of [208Y/120], 3-phase, 4-wire circuits shall be as follows: 1. Line to Neutral: [400 V for 208Y/120]. 2. Line to Ground: [400 V for 208Y/120]. 3. Neutral to Ground: [400 V for 208Y/120]. D. Protection modes and UL 1449 suppressed voltage rating for 240/120-V, single-phase, 3-wire circuits shall be as follows: 1. Line to Neutral: 400 V. 2. Line to Ground: 400 V. 3. Neutral to Ground: 400 V. E. Protection modes and UL 1449 suppressed voltage rating for 240/120-V, 3-phase, 4-wire circuits with high leg shall be as follows: 1. Line to Neutral: 400 V, 800 V from high leg. 2. Line to Ground: 400 V. 3. Neutral to Ground: 400 V. F. Protection modes and UL 1449 suppressed voltage rating for voltages of 240, 480, or 600, 3-phase, 3-wire, delta circuits shall be as follows: 1. Line to Line: [1000 V for 240 V]. 2. Line to Ground: [800 V for 240 V]. 2.5 ENCLOSURES A. NEMA 250, with type matching the enclosure of panel or device being protected. PART 3 - EXECUTION 3.1 INSTALLATION OF SURGE PROTECTION DEVICES A. Install devices at service entrance on load side, with ground lead bonded to service entrance ground. B. Install devices for panelboard and auxiliary panels with conductors or buses between suppressor and points of attachment as short and straight as possible. Do not exceed manufacturer's recommended lead length. Do not bond neutral and ground. 1. Provide multipole, [60] -A circuit breaker as a dedicated disconnect for suppressor, unless otherwise indicated. 3.2 PLACING SYSTEM INTO SERVICE A. Do not energize or connect [service entrance equipment] [panelboards] [control terminals] [data terminals] to their sources until surge protection devices are installed and connected. 3.3 FIELD QUALITY CONTROL A. Testing: Engage a qualified independent testing and inspecting agency to perform field tests and inspections and prepare test reports: B. Testing: Perform the following field tests and inspections and prepare test reports: 1. Complete startup checks according to manufacturer's written instructions. TRANSIENT-VOLTAGE SUPPRESSION FOR LOW-VOLTAGE ELECTRICAL POWER CIRCUITS

12 Reece, Noland & McElrath 2. Perform each visual and mechanical inspection and electrical test stated in NETA ATS, "Surge Arresters, Low-Voltage Surge Protection Devices" Section. Certify compliance with test parameters. END OF SECTION TRANSIENT-VOLTAGE SUPPRESSION FOR LOW-VOLTAGE ELECTRICAL POWER CIRCUITS

13 Hydrant Flow Test Report Test Date 64 Test Time 1:50 Location 48 Haywood Park Dr Clyde, NC Tested by Crawford Sprinkler Company 1814 U.S. Hwy 70 S.W. Hickory, NC Notes Yellow hydrant at corner of Haywood Park Dr. & Hospital Dr Read Hydrant 90 psi static pressure 60 psi residual pressure 0 ft hydrant elevation Flow Hydrant(s) Outlet Elev Size C Pitot Pressure Flow # gpm Flow Graph psi gpm Created with the free hydrant flow test program from

14 Hydrant Flow Test Report Test Date 6/27/2016 Test Time 2:10 Location 390 Jones Cove Rd Clyde, NC Tested by Crawford Sprinkler Company 1814 U.S. Hwy 70 S.W. Hickory, NC Notes Read Hydrant Yellow hydrant at SW corner of Jones Cove Rd. & Hospital Dr 118 psi static pressure 92 psi residual pressure 0 ft hydrant elevation Flow Hydrant(s) Outlet Elev Size C Pitot Pressure Flow # gpm Flow Graph psi gpm Created with the free hydrant flow test program from

15 Haywood County Animal Services Bidders List: Brantley Construction Company, LLC. (828) Jacob Benson Clark & Leatherwood Inc. (828) Lewis Clark Cooper Construction Company, Inc. (828) Eric Oursler Kearey Builders (704) Rick Travis John Burgin Construction (828) M.B. Haynes (828) Kenny Holifield Western Builders of Sylva, Inc. (828) Roger Bartlett B. Allen Construction, Inc. (828) Barry Willis

16 FORM OF PROPOSAL Haywood County Animal Services New Facility Haywood County, NC CONTRACT: DATE: The undersigned, as Bidder, hereby declares that the only person or persons interested in the Proposal as principal or principals is or are named herein and that no other person than herein mentioned has any interest in this Proposal or in the Contract to be entered into; that this Proposal is made without connection with any other person, company or parties making a bid or proposal; and that it is in all respects fair and in good faith without collusion fraud. The Bidder further declares that he has examined the site of the Work and informed himself fully in regard to all conditions pertaining to the place where the work is to be done; that he has examined the Specifications for the Work and the Contract Documents relative thereto, and has read all Special Provisions furnished prior to the opening of bids; that he has satisfied himself relative to the work to be performed, and that he will honor this proposal for sixty (60) days. The Bidder proposes and agrees if this Proposal is accepted to Contract with Haywood County in the form on Contract specified, to furnish all necessary materials, equipment, machinery, tools, apparatus, means of transportation and labor necessary to complete the construction of Haywood County Animal Services Facility and Site Work in full and complete accordance with the Plans, Specifications, and Contract Documents, to the full and entire satisfaction of Haywood County and MOUNTAIN DESIGN, with a definite understanding that no moneywill be allowed for extra work except as set forth in the General Conditions and the Contract Documents, for the sum of: SINGLE PRIME BID: Base Bid: Dollars ($ ) Plumbing Subcontractor Mechanical Subcontractor Electrical Subcontractor Metal Building Subcontractor Allowance No. 1: For site and materials testing as indicated by the drawings and as needed for site conditions allow ten thousand (10,000) dollars. Allowance No. 2: For exterior and interior signage allow ten thousand (10,000) dollars. Labor and materials. Allowance No. 3: For sound absorption panels allow twenty thousand (20,000) dollars. Labor and materials Alternate No. 1: ADD the Multi-Purpose Room, Kitchenette, Storage, and One Toilet as shown on Drawings. Dollars (+$ ) Alternate No. 2: DEDUCT all equipment as shown on equipment schedule and installation labor for same Dollars ($ ) Alternate No. 3: Provide Fire Alarm System manufactured by Edwards Systems Technologies (ETS), Access Control System manufactured by Honeywell, and Security Camera System manufactured by Interlogix. Dollars ($ ) Alternate No. 4: Fire Alarm, Access Control, and Security Camera Systems are to be furnished and installed by Haynes Technologies. Dollars ($ )

17 Unit Price Work: Unit prices will be in effect only when necessary work falls outside the scope of the original contract work. Please insert unit price for all the items listed below (items listed below are an estimate of possible quantities and are not a guarantee of Work or Payment). For all Unit Price Work that occurs outside the above lump sum price, payment shall be made in an amount equal to the sum of the established unit price for each separately identified item of Unit Price Work times the quantity of that item. Description Unit Price Mass Rock Excavation (25 CYDS) Dollars / Cubic Yard Trench Rock Excavation (25 CYDS) Dollars / Cubic Yard Undercut Unsuitable (200 CYDS) Dollars / Cubic Yard And Backfill/Remove Offsite Washed Stone (500 Tons) Dollars / Ton Cast in Place Concrete (100 CYDS) Dollars / Cubic Yard Reinforcing Steel (25 TONS) Dollars /Ton Footing Excavation (25 CYDS) Dollars / Cubic Yard The Bidder further proposes and agrees hereby to commence work under his Contract on a date to be specified in a written order of the Designer (Notice to Proceed) and shall fully complete all work there no later than three hundred and sixty five (365) consecutive calendar days thereafter. Applicable liquidated damages shall be the sum of $500 for each consecutive day thereafter as provided in section 15 of the General Conditions. The Undersigned further agrees that in the case of failure on his part to execute the said Contract and the Bond within ten (10) consecutive calendar days after written notice being given of the award of Contract, the check, cash or bid bond accompanying this Bid shall be paid into the funds of the Owner s account set aside for the Project, as liquidated damages for such failure; otherwise the check, cash of bid bond accompanying this Proposal shall be returned to the undersigned. Attach Certified Check, Cash, or Bid Bond to this Proposal. Respectfully submitted this day of (Name of Firm or Corporation making bid) WITNESS: BY: Title: (Proprietorship or Partnership) (Owner, Partner, Pres, or V. Pres.) ATTEST: By: Address: License No.: Title: (Corp. Sec. Or Ass t Sec. Only) (CORPORATE SEAL)

18 Addendum received and used in computing bid: Addendum No. 1 Addendum No. 4 Addendum No. 2 Addendum No. 5 Addendum No. 3 Addendum No. 6