VICINITY G R EEN W A LL. Installation Guidelines

Transcription

1 VICINITY G R EEN W A LL Installation Guidelines

2

3 System Hardware Overview Irrigation System Pot Rail Pot System Bag Inline Filter Inlet Pipe 6-15mm Overflow Pipe Min 15mm Min 0.6 Tank Stopper Tank Joiner Secondary Tank Master Tank Tank System

4 Components List Pot System Tank System Irrigation System Secondary Tank Master Tank Irrigation Piping Pump Pipe Clips 4 Lph / 1Gph Dripper Hex Pot Grommets Tank Connector End Cap Hose Connector Dripper Hole Punch Dripper Extention Pipe Planter Bag Aluminium 5 Pot Rail Stopper Elbow Pipe Connector T - Connector Inline Filter Equipment Required: (Not Provided) Drop Sheet Drill Tape Measure Hack Saw Box Cutter Silicone Star Screwdriver Flashlight Spirit Level Vacuum Cleaner Soapy Water Masking Tape

5 Step 1: Mounting master tank TIP! Install master tank level in bottom right corner of the wall.

6 Step 2: Joining Tanks Secondary Tank Master Tank Lubricate pipe Insert grommets and push through connector pipe to join tanks.

7 Step 3: Mounting Secondary Tank 40mm / 1.58 Set spacing between tanks between 0-40mm / to adjust the width of the system. Install tanks level. Insert stopper on last tank. 0mm / 0

8 Step 4: Install Drop Sheet (optional) The drop sheet redirects water that escapes the pots due to installation or maintanence errors. Drop sheet must overlap tanks allowing water to run off into either tank TIP! Drop sheet is optional but recommended for indoor installations.

9 Step 5: Install Rails to Tanks Top Rail mounting points This side up Use pilot holes provided on tanks to install the bottom screw on each rail. Insert plug Position rail Silicone through hole in rail Insert screw Bottom

10 Step 6: Level Rails and Secure Level rail and install top screw.

11 Step 7: Stack and Cut Rails Desired Height TIP! Retain off-cuts for use at the end of the installation. TIP! Cut rail on notch provided to fit desired height.

12 Step 8: Pump Assembly 120mm / 4.72 irrigation pipe 70mm / 2.75 irrigation pipe Attach first section of irrigation pipe to pump as shown.

13 Step 9: Pump Installation Secondary Tank Master Tank Place assembled pump into master tank. Place irrigation pipe through notch provided in the master tank. TIP!

14 Step 10: Install Irrigation Pipe Install irrigation pipe using pipe clips to secure to the wall. Use the pipe connectors provided to join the pipe. TIP! Do not install pipe clips directly above rails as they intefere with the drippers.

15 Step 11: Install Inline Filter Cut vertical pipe and insert the inline filter with the arrow pointing up. THIS WAY UP

16 Step 12: Install Drippers Punch hole in pipe above rail. Insert dripper and make sure dripper is at a 45º downward angle. TIP!

17 Step 13: Extend Drippers Feed dripper extention pipe through the pot opening. Press onto dripper nozzle. Cut dripper extention pipe from inside the pot. Ensure pipe is long enough to remain within the pot opening. Correct length Too long Too short Extend dripper and insert into pot.

18 Step 14: Planting of Pots TIP! Feed loose ends of strings through holes in pot. Tie into a bow. TIP! Strings must feed back through Transplant from grow pot to the planter bag. Tie bag into the hex pot.

19 Step 15: Pot Installation TIP! Clip pots onto rails and ensure proper alignment. It is easier to load pots from bottom up.

20 Step 16: Testing Irrigation System Turn on pump and close pressure release valve until drippers all flowing. Check drippers are inserted correctly into pots. Test run the irrigation system for 1-2 hours and observe for leaks.

21 Step 17: Routine Maintanence : Remove dripper, pump filter and inline filter as shown. Clean and re-attach.

22 Step 18: Tank Maintanence Drain water using a wet vacuum cleaner. Clean out all dirt and debris. Refill tanks. : Drain the tanks and wipe down and clean. Refill with fresh water.