DHR Accessories Requirements. Site Preparation Guide

Size: px

Start display at page:

Download "DHR Accessories Requirements. Site Preparation Guide"

Katherine Randall
5 years ago
Views:

1 DHR Accessories Requirements Site Preparation Guide Revision C Issued May 2018

2 Table of Contents Table of Contents... 2 Smart Swap Requirements... 3 Air Chiller System (ACS) ETC Chiller Panel... 8 ACS/Chiller Panel Utility Requirements... 9 ETC Low Temperature Cooling Accessory Circulator (Julabo) Gas Cooling Accessory (GCA) Relative Humidity (RH) Accessory ThermoCube Circulator Gas Flow Requirements Site Preparation Checklist TA Instrument Offices Revision C Issued May 2018 Page 2

Smart Swap Requirements Accessory Asphalt Submersion

Electrically Heated Cylinder (EHC) Optional ambient

690 kpa gauge (30 100 psig) See page 13 for gas flow

206 volume Circulator Power Cooling Gas LN 2 Fluid

3 Smart Swap Requirements Accessory Asphalt Submersion Cell Smart Swap Requiremetns Julabo FP35-HE (PN ) with TA Instruments firmware. See page 10 for circulator requirements. Dielectric Accessory PC with USB port Customer-supplied Agilent E40980A LCR meter Electrically Heated Cylinder (EHC) Optional ambient cooling with clean, dry, oil-free compressed air: kpa gauge ( psig) See page 13 for gas flow volume ETC Viewer Clean, dry, oil-free compressed air kpa gauge ( psig) See page 13 for gas flow volume Circulator Power Cooling Gas LN 2 Fluid Light Hardware Software Temp Lab Customer Revision C Issued May 2018 Page 3

Smart Swap Requirements Accessory Immobilization Cell Smart Swap Requirements Recirculating

Microscope Accessory (MMA) PC with spare network card Fluid circulator required: Magneto-

901) is recommended. See page 14 for ThermoCube requirements.

4 Smart Swap Requirements Accessory Immobilization Cell Smart Swap Requirements Recirculating water bath (supplied) Vacuum pump and pressure gauge with connection for 6mm tubing Modular Microscope Accessory (MMA) PC with spare network card Fluid circulator required: Magneto- Rheology Accessory For open loop temperature control the ThermoCube (PN ) is recommended. See page 14 for ThermoCube requirements. For closed loop temperature control, the Julabo FP35HE (PN ) is recommended. See page 11 for Julabo requirements. Always consult circulator manual for correct combination of fluid and temperature range Circulator Power Cooling Gas LN 2 Fluid Light Hardware Software Temp Lab Customer Revision C Issued May 2018 Page 4

Smart Swap Requirements Accessory Smart Swap Requirements Pressure Cell Compressed inert gas tank up to 13.

Regulators and hose are available from: http://www.buy-compressed-gasregulators.

cooling water from the cell: 206 690 kpa (30 100 psig) See page 13 for gas flow volume Cooling water must be provided. TA Instruments air cooled Heat Exchanger (PN 403209.

5 Smart Swap Requirements Accessory Smart Swap Requirements Pressure Cell Compressed inert gas tank up to 13.8 MPa gauge (2000 psig) with an appropriate regulator High pressure hose and regulator are not supplied with the Pressure Cell option. Regulators and hose are available from: or from your local high-pressure gas bottle supplier Starch Pasting Cell Small Angle Light Scattering (SALS) Clean, dry, oil-free compressed air is required to purge cooling water from the cell: kpa ( psig) See page 13 for gas flow volume Cooling water must be provided. TA Instruments air cooled Heat Exchanger (PN ) is recommended (distilled water required with use of the Heat Exchanger). Refrigerated circulator is required for cooling below ambient. As per Peltier Plate (Refer to the DHR Site Preparation Guide for requirements) Circulation fluid temperature should not be below ambient Circulator Power Cooling Gas LN 2 Fluid Light Hardware Software Temp Lab Customer Revision C Issued May 2018 Page 5

Smart Swap Requirements Accessory UV Light

Customer-supplied light source must be an

required with use of the Heat Exchanger.

6 Smart Swap Requirements Accessory UV Light Guide Smart Swap Requirements Customer-supplied light source must be an EXFO Omnicure Series 2000 UVLED As per the Peltier Plate (Refer to the DHR Site Preparation Guide for requirements) Circulation fluid should not be below ambient TA Instruments air cooled Heat Exchanger (PN ) is recommended; distilled water required with use of the Heat Exchanger. Circulator Power Cooling Gas LN 2 Fluid Light Hardware Software Temp Lab Customer Revision C Issued May 2018 Page 6

Panel ACS-3 MEASUREMENTS Height: 112 cm (44 in) Width: 37 cm (14.5 in) WITHOUT Chiller Panel Width: 52 cm (20.

7 Air Chiller System (ACS) Height: 88.5 cm (35 in) Width: 37 cm (14.5 in) WITHOUT Chiller Panel Width: 52 cm (20.5 in) WITH Chiller Panel Depth: 56 cm (22 in) Weight: 96 kg (211 lbs) WITHOUT Chiller Panel Weight: 112 kg (247 lbs) WITH Chiller Panel ACS-3 MEASUREMENTS Height: 112 cm (44 in) Width: 37 cm (14.5 in) WITHOUT Chiller Panel Width: 52 cm (20.5 in) WITH Chiller Panel Depth: 56 cm (22 in) Weight: 121 kg (267 lbs) WITHOUT Chiller Panel Weight: 137 kg (302 lbs) WITH Chiller Panel Revision C Issued May 2018 Page 7

8 ETC Chiller Panel ETC CHILLER PANEL MEASUREMENTS Height: 86.4 cm (34 in) Width: 48.3 cm (19 in) Depth: 38.1 cm (15 in) Weight: 15.8 kg (35 lbs) Revision C Issued May 2018 Page 8

9 ACS/Chiller Panel Utility Requirements POWER VAC 50 Hz or 60 Hz (refer to the serial number plate on the rear of the unit) Nominal 9.3A (Max 12A) GAS Gas Pressure Flow Rate Temperature Dew point Laboratory Room Temperature Cooling Gas: Air or Nitrogen bar ( psig) See page 13 for gas flow volume C Must not exceed the ambient air temperature by more than 5 C. Dew point is specified at operating temperature. 12 C 21 C = Acceptable 21 C 24 C = Ideal Operating altitude: 2000 m maximum Relative humidity: 5% 80% RH from 15 C 24 C Revision C Issued May 2018 Page 9

10 ETC Low Temp Cooling Accessory LIQUID NITROGEN Customer-supplied bulk low-pressure liquid nitrogen tank ( liters) with a 23 psig relief valve. Revision C Issued May 2018 Page 10

Julabo Circulator Julabo FP-35 is used with the Asphalt Submersion Cell and the Julabo FP-32 is used with the Magneto Rheology Accessory JULABO MEASUREMENTS Height: 64 cm (25 in) Width: 3.

11 Julabo Circulator Julabo FP-35 is used with the Asphalt Submersion Cell and the Julabo FP-32 is used with the Magneto Rheology Accessory JULABO MEASUREMENTS Height: 64 cm (25 in) Width: 3.5 cm (12 in) Depth: 43 cm (17 in) Weight: 34 kg (74 lbs) POWER 115 VAC at 60 Hz (14 A) 230 VAC at 50 Hz (12 A) 15 A with receptacle and plug FLUID Bath Fluid Temperature Range Distilled or deionized water 5 C to 80 C Water/glycol mixture (1:1) -20 C to 50 C Julabo H10 80 C to 170 C For the Extended Temperature Module, the temperature range -10 C 170 C must use the Julabo H10 fluid to reach 170 C. Revision C Issued May 2018 Page 11

Gas Cooling Accessory (GCA) Used with Electrically Heated Plates GCA MEASUREMENTS Standard diameter: 51 cm (20 in) Height: 107 cm (42 in) Width: 46 cm (18 in) Depth: 79 cm (31 in) Weight EMPTY: 40 kg

12 Gas Cooling Accessory (GCA) Used with Electrically Heated Plates GCA MEASUREMENTS Standard diameter: 51 cm (20 in) Height: 107 cm (42 in) Width: 46 cm (18 in) Depth: 79 cm (31 in) Weight EMPTY: 40 kg (101 lbs) Weight FULL: 87 kg (191 lbs) POWER 120 VAC at 0.9 KW, Hz OR TA Instruments transformer (PN ) for 220 VAC environments LIQUID NITROGEN Bulk low-pressure liquid nitrogen tank to refill the 50 L GCA dewar Pressure: kpa gauge (22 25 psig) Revision C Issued May 2018 Page 12

8 cm (20 in) Weight EMPTY: 27 kg (60 lbs) POWER 90 260 VAC, 45 65 Hz GAS Dry nitrogen or gas

13 Relative Humidity (RH) Accessory HUMIDITY GENERATOR MEASUREMENTS Height: 36.8 cm (14.5 in) Width: 30.5 cm (12 in) Depth: 50.8 cm (20 in) Weight EMPTY: 27 kg (60 lbs) POWER VAC, Hz GAS Dry nitrogen or gas must be available to the dryer supplied with the Relative humidity option Pressure: kpa ( psig) WATER Distilled water Revision C Issued May 2018 T Page 13

14 ThermoCube Circulator Used with Magneto Rheology Accessory THERMOCUBE MEASUREMENTS Height: 32 cm (12.75 in) Width: 28 cm (11 in) Depth: 32 cm (12.75 in) Weight: 14 kg (28 lbs) POWER VAC at 50/60 Hz (3.5 A) 15 A with receptacle and plug WATER 75% water and 25% glycol mixture Revision C Issued May 2018 T Page 14

15 Gas Flow Requirements GAS FLOW REQUIREMENTS FOR DHR AND ACCESSORY COMBINED DHR accessory combined (instrument and accessory) compressed air flow rates: Accessory Air Cooling System (ACS) Dielectric Accessory Electrically Heated Cylinder (EHC) Environmental Test Chamber (ETC) Viewer Gas Cooling Accessory (GCA) Immobilization Cell Magneto Rheology Modular Microscope Accessory (MMA) Pressure Cell Relative Humidity (RH) Accessory Single Angle Light Scattering (SALS) Starch Pasting Cell Submersion Cell UV LED UV Light Guide Flow Rate 200 L/min 5 17 L/min 3 L/min 3 L/min Revision C Issued May 2018 T Page 15

16 Site Preparation Checklist Discovery Hybrid Rheometer Accessories Accessory (check all that apply): ACS and ETC Chiller Panel Asphalt Submersion Cell Dielectric Accessory EHC ETC Viewer GCA Immobilization Cell Julabo FP35-HE Circulator MMA Magneto Rheology Accessory Pressure Cell RH Accessory Starch Pasting Cell SALS ThermoCube Circulator UV Light Guide UVLED I hereby acknowledge that all utility requirements for the accessories checked above have been met per this document and that they will be ready at the agreed time of installation. If all utility requirements are not met at the agreed time of installation, additional charges may be incurred for a return Service trip. Customer DD MM YYYY Company City State Country Please send a signed copy of the completed checklist to your local Service representative. Revision C Issued May 2018 T Page 16

17 TA Instruments Offices For information on our latest products, contact information, and more, see our website at: To find your local TA Instruments office and contact information, visit TA Instruments Waters LLC Corporate Headquarters 159 Lukens Drive New Castle, DE USA Telephone: Fax: Revision C Issued May 2018 T Page 17

TA Instruments Installation Requirements for Rheology Systems

TA Instruments Installation Requirements for Rheology Systems Notice TA Instruments Installation for Rheology Systems Thank you for ordering a rheology system from TA Instruments. To ensure that installation of your system goes as smoothly as possible and has you