BIOSTORE HEATING ROLL IN CABINETS SCC 1010, SCC 2320, SCC 1120, SCC 2340 TECHNICAL MANUAL INCLUDING - USER MANUAL - INSTRUCTIONS

Transcription

1 HEATING ROLL IN CABINETS BIOSTORE SCC 1010, SCC 2320, SCC 1120, SCC 2340 TECHNICAL MANUAL INCLUDING - USER MANUAL - INSTRUCTIONS BONNET GRANDE CUISINE Rue des Frères Lumière - Z.I. Mitry Compans MITRY MORY cedex Tél Fax FORM050B1/1 n /02

2 RECTO

3 USER MANUAL HEATING ROLL IN CABINETS BIOSTORE SCC 1010, SCC 2320, SCC 1120, SCC 2340 CONTENTS Important recommendations 2 1. Presentation of the control panel 3 2. Use 4 3. Maintenance 5 BONNET GRANDE CUISINE Rue des Frères Lumière - Z.I. Mitry Compans MITRY MORY cedex Tél Fax User Manual n Page 1

4 IMPORTANT RECOMMENDATIONS This cabinet is designed for use in Restaurants or Catering facilities. It is not intended for industrial use. Installation should be undertaken by a refrigeration engineer. Do not modify the electrical connection made during installation, particularly the earth continuity circuit. The supply cable that is fitted is a specific part and should only be replaced with an original part. Ensure that the plug is easily accessible. In the event of problems with the electrical circuit, only the installer or the manufacturer should intervene. Observe hygiene guidelines by regularly cleaning the following :. interior fittings. door seal. interior lining Do not use corrosive or acidic products. Water splashing can cause damage.. To avoid the risk of splash damage, do not clean with a hose or high-pressure spray.. Do not locate the unit where it is exposed to the elements. SPECIFICATION AND CHARACTERISTICS IN THIS DOCUMENT MAY BE SUBJECT TO BE MODIFIED WITHOUT PRIOR NOTICE User Manual n Page 2

5 1. PRESENTATION OF THE CONTROL PANEL 1.1 IMPORTANT The thermostat does not cut the power supply to the appliance. 1.2 CONTROL PANEL / On/Off switch. 2/ Power-on led. 3/ Security thermostat reset switch. In order to avoid problems of overheating, (air turbine shut-down or defective, thermostat out of adjustement or defective) the system is equipped with a manual reset security thermostat with a fixed set-point of 110 C. When the thermostat is actuated, it cuts out the power supply to the resistances, turbine(s), hygrometer (see model) and the red led lights up. To reset the thermostat, wait a few minutes and press the button. 4/ Security led. It only switches off when the security thermostat has been reset. 5/ Thermometer indicating cabinet interior temperature. 6/ Ambient thermostat, max. set-point set in factory at +85 C. NOTE : The constructor is not responsible if the factory set-point is changed. 7/ On/Off hygrometer switch (see model). In the "ON" position, the hygrometer operates continuously. 4 User Manual n Page 3

6 2. USE 2.1 GENERAL REQUIREMENTS When operating for the first time or after a prolonged period out of use the unit should be run empty. Items should only be loaded when the set temperature has been reached. The security thermostat will operate if too hot products are stored. 2.2 LOADING A space of at least 15 mm is required between each item to allow refrigerated air to pass around the products. NOTE : To respect performance, the operating characteristics are given for covered dishes. 2.3 VENTILATION The ventilation is ensured by the air turbine(s). Warning: their sense of rotation is indicated on the motor. WARNING: The motor of the air turbine, which is equipped with a cooling turbine, is located on the top of the cabinet. It is therefore recommended to switch off the cabinet before any intervention. 2.4 HEATING The power supply to the resistances is controlled by the ambient thermostat. NOTA : When the door(s) is/are opened, the power to the ventilation, heating and hygrometer (see model) is cut. The cabinet will operate correctly only if the factory settings are maintained. The manufacturer declines all responsibility for any defective operation resulting from changes made to these settings. User Manual n Page 4

7 3. MAINTENANCE IMPORTANT Before cleaning ensure that the appliance is unplugged. Do not use a spray hose 3.1 INTERIOR LINING This should be cleaned daily. 3.2 STAINLESS STEEL Use warm soapy water or a non corrosive cleaner then rinse thoroughly and dry. Do not use abrasive, aggressive or concentrated cleaning products. Where necessary use scotch brite or proprietary stainless steel cleaner. 3.3 REGULAR CLEANING. The door seals can be removed easily for cleaning. User Manual n Page 5

8 Recto

9 INSTRUCTIONS HEATING ROLL IN CABINETS BIOSTORE SCC 1010, SCC 2320, SCC 1120, SCC 2340 CONTENTS Important recommendations 2 1. Technical data 3 2. Installation 5 3. Operation 8 4. Intervention and repairs 9 5. Electrical diagrams Spare parts 16 BONNET GRANDE CUISINE Rue des Frères Lumière - Z.I. Mitry Compans MITRY MORY cedex Tél Fax Instructions Manual n Page 1

10 IMPORTANT RECOMMENDATIONS There must be earth continuity between the appliance and the mains connections. The supply cable that is fitted is a specific part and should only be replaced with an original part. Ensure that the plug is easily accessible. The installer should ensure that the electrical connection is suitably protected by an appropriate fuse or circuit breaker (see rating plate). Ensure that the appliance is switched OFF before any intervention on the electrical circuit and during cleaning Water splashing can cause damage.. To avoid the risk of splash damage do not clean with a hose or high-pressure spray.. Do not locate the unit where it is exposed to the elements. After any intervention ensure that the original installation guidelines are respected to avoid any form of risk. SPECIFICATIONS AND CHARACTERISTICS IN THIS DOCUMENT MAY BE SUBJECT TO BE MODIFIED WITHOUT PRIOR NOTICE Instructions Manual n Page 2

11 1. TECHNICAL DATA 1.1 SCC 1010 and SCC 1120 CONSTRUCTION Austenitic S/S exterior casing (sides, front panel, door) and interior lining. Rear and top of the exterior casing in corrosion proof galvanized sheet. Austenitic S/S interior door. Insulated body - Demountable panel type (delivered assembled). - Polyurethane foam insulation, 60 to 75 mm thick - Thermal break between inner and outer structure. - Cabinet stability: no adjustment required except shims Plain door - Easily removable magnetic seal. - Door with security lock hold and self closing door. - Door opening can be reversed (1 porte) TECHNICAL DATA Voltage : 3N~400V 50 Cycle Input power : 3500 W Protection : am 6 Delivered with a moulded plug. The fitter is responsible for protecting the appliance against overloads or electrical defects. Ensure a circuit-breaker or fuses are installed. Power Type of resistances Type of ventilation : 3000 W : Impervious armoured S/S : Reaction type air-turbine Complies with Electric Security : EN Food Hygiene : NF U Complies with E.C requirements For hygrometer option, water connection outlet = ¾ (20/17) F Instructions Manual n Page 3

12 1.2 SCC 2320 and SCC 2340 CONSTRUCTION Austenitic S/S exterior casing (sides, front panel, door) and interior lining. Rear and top of the exterior casing in corrosion proof galvanized sheet. Austenitic S/S interior door. Insulated body - Demountable panel type (delivered assembled). - Polyurethane foam insulation, 60 to 75 mm thick - Thermal break between inner and outer structure. - Cabinet stability: no adjustment required except shims Plain door - Easily removable magnetic seal. - Door with security lock hold and self closing door. - Possibilité d'inversion du sens de fermeture (1 porte) TECHNICAL DATA Voltage : 3N~400V 50 Cycle Input power : 7000 W Protection : am 10 Delivered with a moulded plug. The fitter is responsible for protecting the appliance against overloads or electrical defects. Ensure a circuit-breaker or fuses are installed. Power Type of resistances Type of ventilation : 6000 W : Impervious armoured S/S : Reaction type air-turbine Complies with Electric Security : EN Food Hygiene : NF U Complies with E.C requirements For hygrometer option, water connection outlet = ¾ (20/17) F Instructions Manual n Page 4

13 2. INSTALLATION 2.1 GENERAL REQUIREMENTS The appliance must be installed, modified and repaired by a specialized engineer in accordance with current regulations. 2.2 HANDLING The appliance must be handled with suitable lifting equipment, transported on its original pallet and not stacked. If moving the appliance without its pallet, it must be carried and not pulled. 2.3 UNPACKING AND INSTALLATION LOCATION IMPORTANT : Roll in cabinets do not have adjustable feet, therefore they must be placed on a smooth and level floor UNPACKING After unpacking, slide the cabinet off its pallet. Ensure that the weight of the cabinet is evenly distributed. SILICONE SOCLE PALETTE When the cabinet is in its final location, remove the handling stiffener(s) located inside and apply silicon mastic between the base and the floor. Instructions Manual n Page 5

14 2.4 DISMANTLING THE CABINET The design allows the cabinet to be dismantled if required for access. 1) Remove the door hinges. 2) Undo the upper control panel screws and rest the panel on the top of the appliance to avoid disconnecting it) 3) Remove the top assembly by unscrewing the 3 screws on each side and on twin trolley models unlocking the verticals using an Allen key. 4) Undo and remove the following : - the rear on roll in models - the vertical on twin trolley models - the sides 2.5 ASSEMBLING THE CABINET NOTA : Factory non-assembled units arrive in two cases. One contains the base, the equipped top, control panel and fixings. The other the panels (sides, door(s), rear, verticals) and fixings. The electrics and refrigeration do not require installation. During assembly, apply a bead of silicone to the panels to ensure a good seal. 1) Put the base on the floor and fit the 8 mm studs into the assembly positions. 2) Locate the side panels, adjust the fit then lock them to the base using an Allen key (Turn clockwise until a click is heard) 3) Lock the side panels together. 4) On twin trolley models, fit 8 mm studs into the top of the verticals. 5) Put the equipped top onto and between the sides ensuring that they stay in position until fixed using the 6 HM8x70 screws and washers, do not fully tighten. 6) Lock the verticals into the top. 7) Slide the control panel into its top locating grooves then fix using the 2 HM6x10 screws 8) Fit the doors to their hinges Finish by tightening carefully then fit covers to all the assembly holes. Instructions Manual n Page 6

15 2.6 EXPLODED VIEW 1) Base 2) Left side 3) Right side 4) Rear 5) Equipped top 6) Door 7) Control panel 9) HM6x10 screws 10) MN8 washers 11) HM8x70 screws 12) φ 30 Hole cover plugs 13) φ 8 studs 14) Allen key 15) φ 15 Hole cover plugs 16) Rear casing 17) Upper casing Instructions Manual n Page 7

16 2.7 ELECTRICAL CONNECTION See paragraph 1 "Technical data". A circuit-breaker or suitable fuses should be provided on the supply. The appliance is fitted with a supply cable that should not be removed. This unit must be earthed (see recommendations). 2.8 WATER CONNECTION FOR HYGROMETER OPTION For the water connection use the supplied hose connected to the cabinet with a ¾ (20/27) F thread. 3. OPERATION 3.1 GENERAL REQUIREMENTS Before operation, you should master the various control, setting and checking components 3.2 CONTROL PANEL LAYOUT See USER MANUAL Instructions Manual n Page 8

17 4. INTERVENTIONS AND REPAIRS IMPORTANT Before any operation, ensure that the appliance is unplugged Remove the upper casing to have access to the air-turbine. Operations on the electrical plate (the way to get to the regulation) are easier with the control panel removed. Remove the control panel by removing the 2 upper screws. Upper casing Upper screws Régulation Cabinet top Control panel Lower locating axle Instructions Manual n Page 9

18 5. ELECTRICAL DIAGRAMS TROLLEY CABINET (N SE030) Instructions Manual n Page 10

19 5.2 2 TROLLEYS CABINET (N SE031) Instructions Manual n Page 11

20 5.3 1 TROLLEY CABINET - POW. 230 V 3 ~ (N SE034) Instructions Manual n Page 12

21 5.4 2 TROLLEYS CABINET - POW. 230 V 3 ~ (N SE035) Instructions Manual n Page 13

22 5.5 1 TROLLEY CABINET - POW. 230 V ~ (N SE036) Instructions Manual n Page 14

23 5.6 HYGROMETER OPTION (N SE037) TROLLEY CABINETS TROLLEYS CABINETS POWER MEASURE RELAY SETTINGS - I = Opposite - T1 = min. - T2 = min. - Hysteresis = % le = mini. - Point le = 20% Instructions Manual n Page 15

24 6. SPARE PARTS 6.1 CASING SCC 1010 SCC 2320 SCC 1120 SCC 2340 CODE DESIGNATION S998PB53 Insulated plain door S204P16 Aluminium surround glazed door S356P11 702x1863 Magnetic seal S090P01 Door hinge S092P01 Door handle S551PM43 Solid door wiper joint fixing S552PM43 Solid door wiper joint fixing S113PM43 Glazed door wiper joint fixing S553PM43 Solid door wiper joint S114PM43 Glazed door wiper joint S534P43 Single trolley control panel S535P43 Twin-trolley control panel S530PN43 Single trolley rear facia S531PN43 Twin-trolley rear facia 6.2 ELECTRIC AND REFRIGERATING EQUIPMENT SCC 1010 SCC 2320 SCC 1120 SCC 2340 CODE DESIGNATION S362P15 On/Off switch S368P15 On/Off switch contact S297P15 Power up green light S050P20 Regulation thermostat S058P20 Thermometer S082P20 Safety thermostat S383P15 Reset button S073P11 Reset button cam S298P15 Safety red light S128P15 Microswitch S068P15 Light S104P15 Turbine and resistances contactor S443P15 air-turbine S441P43 Turbine casing S444P15 Suction intake S124P15 Coil resistance S058P15 Cable clamp S846P51 3P+N+T plug Instructions Manual n Page 16

25 6.3 HYGROMETER SPECIFIC EQUIPMENT SCC 1010 SCC 2320 SCC 1120 SCC 2340 CODE DESIGNATION S362P15 On/Off switch S368P15 On/Off switch contact S120P15 Intensity relay S089P20 Solenoid valve S114P19 Water supply hose S142P15 PTC 12X180 Heating cartridge S439PM43 Water tank Instructions Manual n Page 17

26 DECLARATION DE CONFORMITE CONFORMITY DECLARATION HERSTELLERKONFORMITÄTSERKLÄRUNG TYPE / TYPE / TYP : N DE SERIE / SERIAL N / FAB Nr : Cet appareil est conforme aux dispositions de la directive «Basse tension» 73/23/CEE et de la directive «Compatibilité électromagnétique» 89/336/CEE. This appliance complies with the provisions of the low voltage directive EEC/73/23 and with the provisions of the electromagnetic compatibility directive EEC/89/336. Dieses Gerät entspricht nach den Bestimungen der niederspannung-richtlinie EWG/73/23 und den Bestimmungen der elektromagnetischen Übereinstimmung-richtlinie EWG/89/336. Il est également conforme aux dispositions de normes européennes harmonisées suivantes : It is in compliance with the following harmonized standards : Und entspricht ebenfalls der folgenden Europaïschen Norme : - EN Sécurité des appareils électrodomestiques et analogues Safety of houseold and similar electrical appliances Elektrische Geräte für den Hausfebrauch und ähnliche Zwecke DIRECTION GENERALE Général Manager Betriebsleiter FORM055A1/1 Siège Social : BONNET GRANDE CUISINE. Rue de Frères Lumière, Z.I. de MITRY COMPANS, MITRY MORY CEDEX Tél. : Fax : S.A.S au capital de Euros. - RCS MEAUX B