COOLING CHAMBER ODP. Instrukcja obsługi p Service manual p Bedienungsanleitung. Инструкция по бслуживанию p p.

Transcription

1 COOLING CHAMBER ODP pl de ru Instrukcja obsługi p Service manual p. 2-7 Bediungsanleitung p Инструкция по бслуживанию p

2 DEAR CUSTOMERS! Contts Service manual COOLING CHAMBER ODP Thank you for purchasing our production equipmt. We hope that thanks to its advantages, our device will serve you well and for a long time. Please familiarize yourself with this manual. The information contained therein will facilitate the use of the product and will allow for long-lasting and reliable operation of the device. Our company s devices have be manufactured in accordance with safety standards and have a positive opinion of the National Institute of Hygie. I.Product characteristics p.3 II.Unloading p. 4 III.Preparing the device for operation p. 7 IV.Operation p. 7 Before you call the service In the evt of any difficulties during the start-up of the device or during its operation, return to these chapters of the service manual that explain the operation being performed. This is to make sure that the device is properly handled. If the problems persist, the following tips will help you to remove them. The device is not working... - Make sure that: Voltage and frequcy in the network are the same as those recommded by the manufacturer, it is 230V and 50Hz. The device is connected to the electricity network. The device switches on the control thermostat and the main switch are on. The device does not reach the right temperature. Make sure that: The unit switch is in ON position. The temperature setting on the thermostat is set accordingly. Make sure that the condser is not contaminated, clean it, if necessary. Ambit temperature is not higher than 25 o C. The manufacturer does not guarantee appropriate temperatures at these temperatures. The device is working, sound signaling is turned on... - Make sure that: The condser is not contaminated, clean if necessary. The condser fan is working. The ambit temperature does not exceed 25 o C. If the problems still persist, contact your local Igloo service cter, giving the serial number and model of the device prest on the machine s nameplate. To sure minimum ergy consumption: do not place the device close to heat sources sure air circulation around the device avoid unnecessary door oping and leaving it op for a long time This marks information of particular relevance to user safety and proper operation of the device Service Manual COOLING CHAMBER ODP 1, ODP 2 2

3 I.Product characteristics Folded cooling chamber, designed for refrigeration and storage of goods in containers at an ambit temperature of 10 C to 25 C and air humidity up to 60 ± 5%. Service Manual COOLING CHAMBER ODP 1, ODP 2 3

4 Geral information: Our devices have be made according to modern technologies suring high durability and good operating parameters. The temperature in the chamber is betwe +4 and +8 C Device equipmt: Wh you buy our devices, you receive with the device: operating manual warranty card II. Unloading The chambers are delivered completely assembled on a special pallet. The device on the pallet should be unloaded by hand or with a suitable hoist (forklift, pallet truck), always in the normal use position. The maximum angle of inclination from the vertical direction is 15 degrees To sure long-lasting and effective operation of the device, the user should observe the following rules: 1. Do not fill the device with the product before it has cooled down (about 1 ~ 2 hours from the momt of starting) 2. Do not put warm products in cold chambers 3. The product should be distributed so as not to block the vtilation opings 4. Do not leave op covers and doors 5. At least once a month or in case of contamination, clean the condser. The method of cleaning the condser is shown on p The device should be cleaned with warm water with the addition of non-abrasive cleaning agts after disconnecting the device from the mains. It is forbidd to use corrosive agts, they can lead to irreparable damage to the surface of the device. In daily use, top covers are used to load the containers in the chamber (see fig.) To replace the containers op the door and unload the container. 4 Service Manual COOLING CHAMBER ODP 1, ODP 2

5 The device s operation is controlled by a temperature controller that is equipped with: unit switch allowing to switch off the unit at any time without disconnecting the power supply of the refrigeration unit; manual defrost button abling the defrost cycle to be activated at any time during the operation of the refrigeration device (regardless of the automatic defrost function); The button does not work wh the temperature is higher than the temperature of the d of the defrost. temperature preview button for defrost ssor or ssors and the condser temperature monitoring ssor. If the admissible temperature of the condser is exceeded, the user is notified by a sound signal. In this situation, clean the condser, check whether the condser fan works or ambit temperature does not exceed 25 C. digital temperature display that allows currt temperature control inside the refrigeration device To sure long-lasting and effective operation of the device, the user should observe the following rules: 1. Do not fill the device with the product before it has cooled down (about 1 ~ 2 hours from the momt of starting) 2. Do not put warm products in cold chambers 3. The product should be distributed so as not to block the vtilation opings 4. Do not leave op covers and doors 5. At least once a month or in case of contamination, clean the condser. The method of cleaning the condser is shown on p The device should be cleaned with warm water with the addition of non-abrasive cleaning agts after disconnecting the device from the mains. It is forbidd to use corrosive agts, they can lead to irreparable damage to the surface of the device. In daily use, top covers are used to load the containers in the chamber (see fig.) To replace the containers op the door and unload the container Service Manual COOLING CHAMBER ODP 1, ODP 2 5

6 Top cover Main switch Control panel Doors Clean here To set the chamber in the place of use, cut the protective bands, remove the film from the chamber and remove the protective blocks on the pallet. Th, four persons manually unload the chamber from the pallet (a strip with holders mounted on the chamber is used for this). Wh unloading, use protective gloves (protecting hands) and pay atttion to evly raise and lower the chamber. After placing the chamber in the place of use, remove the strips used to unload the chamber from the pallet. GOOD GOOD Strip with holders for unloading WRONG WRONG Device transport 6 Service Manual COOLING CHAMBER ODP 1, ODP 2

7 III. Preparation of the device for operation. The chambers can be installed in closed rooms where vtilation is provided, or under roofs (shelters) protecting the device against atmospheric precipitation. If the chamber is installed in a closed room, vtilation must sure that the temperature inside the room is not higher than 28 C. Therefore, the room should have vtilation opings located so as to sure the passage of fresh air through the tire room (it is recommded to perform forced vtilation by using an extraction fan). The chamber should be placed on a concrete floor or on a leveled base protected against water logging. The device should be placed in a dry place, not exposed to sunlight, suring good exchange of air far from heat sources (stoves, batteries, heaters, etc.) The device should be connected to a separate properly made electric circuit ( % V / 50 Hz with a bipolar plug socket, with a protective pin). The socket should be protected with a fuse of min. 6.0 A, max. 16A. WARNING: It is forbidd to connect the device through extsion cords or distributors. After performing these operations, the device is ready to start working IF YOU DO NOT APPLY TO THE TERMS AND CONDITIONS CONTAINED IN THIS MANUAL CONCERNING THE CONNECTION AND OPERATION OF THE DEVICE, THE MANUFACTURER RESERVES THE RIGHT TO WITHDRAW FROM GUARRANTOR OBLIGATIONS!!! IV. Operation. How to start the device: 1. Insert the plug of the connecting cable in the plug socket 2. Activate the main switch button 3. Turn on the unit using the button located on the temperature regulator panel (see the drawing of the regulator) 4. Set the desired temperature using the buttons on the temperature regulator panel (see the drawing of the regulator) within the range of 4-8 C Service Manual COOLING CHAMBER ODP 1, ODP 2 7

8 Correspondce: Stary Wiśnicz 289, Nowy Wiśnicz Poland NIP: Tel.: / , fax: / , 8 Service Manual COOLING CHAMBER ODP 1, ODP 2