CB-CW-1 Cool/Warm Mattress Owner s Manual. Contents

Transcription

1 CB-CW-1 Cool/Warm Mattress Owner s Manual Contents I II Instructions Product list III Warning for usage IV Common malfunction and Methods of Exclusion V Daily maintenance and cleansing VI After-sales service - 1 -

2 I Instructions 1. Product parameter Heating parameter Cooling parameter Voltage input AC90~230V Working voltage DC12V Rated frequency 50/60Hz Rated frequency 50/60Hz Power for warming 300W Power for Cooling 8W Power for temperature 6W preservation Noise for heating 30 Db Noise for cooling 40 Db Timing range 1-12 hours Timing range 1-12 hours Range for temperature 25~60 Cooling range 1~5 level regulation Tank volume 4.6L Tank volume 4.6L Mattress size Single bed:180cm 70CM Double bed:180cm 140CM Double bed:180cm 143CM 2. Blanket, with options 3. Instructions for the machine and remote buttons On/off: press this button, the machine is assumed to be on warm function, and it is off in 12 hrs - 2 -

3 automatically. Warm: press this button, the machine is under heating condition. The screen shows water temperature at xx and xxh in turn, which means current temperature and the timing to be off automatically respectively. The fan doesn t work. Cool: press this button, the machine is under cooling condition. The screen shows xx L and xxh in turn, which means current cooling level and the timing to be off automatically. The fan starts and works. Timing: press this button to regulate + -. Power-off can be set based on your needs. The screen shows xx L or xx,and xxh in turn, which means the timing set to be off under warm or Cool. Anion:press this button to start anion, press again to turn off anion. The screen shows whether it is on or off. (This function only exists in the remote and works only under cool, and doesn t work under warm ) SLEEP: press this button so temperature or cooling effect can be set automatically. 4. Steps for usage and illustration How to connect? power Main unit Connect to silicone tube mattress remote Notice: A. When you re using warm, connect the silicone tube to the port behind main unite: 1 outlet and 3 warm water; B. When you re using cool, connect the silicone tube to the port behind main unite: 1 outlet and 2 cold water; C. Outlet is shared no matter whether you are using warm or cold

4 Inspection Check the connection between main unit and mattress; place the main unite 20CM higher than mattress, and take out battery film-coated tablets inside the remote. Add water and turn on the machine Plug the main unit to a socket with AC110~230V and 50~60Hz so it would be ready; Screw tank lid and fill purified water (use tap water when it s cool ) into the tank till full; press on/off and machine works. As the water flows into the mattress, all water until the maximum water level mark is reached. Cautions: 1. Water addition should be based the requirement of cool or warm, add water to either the highest level in Cool or the highest level in warm 2. When water level in the tank reaches the lowest level, warning for lack of water alarms and the machine stops working; and then water should be added to keep the machine going. Function of warm At winter, press the button warm (check if the inlet for warm water and outlet are connected to the mattress), the main unit screen shows xx (beginning temperature) and 12H(timing for being off) in turn, and set temperature and the time to be off according to actual needs. When you re setting temperature, first press warm and C blinks on the screen, then press + or - to regulate. When the set temperature is reached, stop for 2 seconds and setting is completed. If timing needs to be set, press time and the screen shows xxh, H blinks on the screen, then press + or - to regulate the timing you need, stop for 2 seconds and setting is completed. If you don t press time, the timing is assumed to be 12H (meaning the machine is off after 12 hours). If you need to turn off timing, press time and then press + or - till - 4 -

5 the screen shows off. ( for temperature,h for hour) Function of cool At summer, press the button cool (check if the inlet for cold water and outlet are connected to the mattress), the main unit screen shows 05L(cooling level) and 12H(timing for being off) in turn, and set the cooling level and the time to be off according to actual needs. When you re setting cooling level, first press cold and L blinks on the screen, then press + or - to regulate. When the set level is reached, stop for 2 seconds and setting is completed. (L for level and H for hour) The steps to set the timing is seen above. Function of anion When cool is on, the screen shows level and time, meanwhile anion starts. When your want to turn off anion, press the button anion till the mark for anion disappears on the screen, meaning anion is off. When your want to turn on anion, press the button anion and the screen shows the mark for anion, meaning anion is on. Function of sleep A: press this button when warm is on, so temperature is set to be 38,and the time to be off is 12 hours during which the machine is working. The screen shows xx and 12H in turn (the function for sleep can be off once other buttons like on/off, cool and hold are pressed.) B: press this button when cool is on, so cooling level is set to be 03L and the time to be off is 12 hours during which the machine is working. The screen shows 03L and 12H in turn (the function for sleep can be off once other buttons like on/off, cool and hold are pressed.) Water discharge Turn off the machine, first unplug silicone tube to let the water out. If there is a little water left inside the machine, tilt the main unit till the remaining water pours out

6 IV Product list No. Item Number 1 Main unit 1 2 remote 1 3 Connection tube 2 4 blanket 1 5 instructions 1 6 Quality certificate 1 7 Silicone stopper for inlet and outlet 2 V Warning for usage 1. The main unite should be placed in somewhere dry, tidy and ventilated. No object should be put on the top of main unit. The main unit should be 20CM above mattress to avoid water leakage. At winter, put a tower under the base of main unit to prevent its resonance with desk. 2. The power can only be on when the joint in the mattress must be firmly connected to main unit, the mattress is made flat and an extra sheet must be put on the blanket at winter. 3. When you switch between warm and cold, make sure the water inlet is changed accordingly. 4. The valuables should not be put around main unit, in case someone knock them down and some other reasons cause water leakage to damage the valuables. 5. Do not disconnect outlet or inlet and screw the tank lid while main unit is working, in case you get scalded by water leakage. 6. When the blanket connects to tube; 7. While the machine is on, as the screen light affects sleeping, screen light is off after the machine is controlled by micro-computer for 2 minutes. The rotating light for work keeps on and the machine is under normal condition. If regulation is needed, press the button again to regulate

7 8. The children, the elderly and the disabled are only using this machine under the supervision of adults and professionals. VI Common malfunction and Methods of Exclusion approaches. Should any situation below occurred, users are advised to deal with it in the following Common Malfunction Failure to start up Water leakage Failure to cool down or cooling effect is poor Situations The socket doesn t work or power cut Fail to connect power source or fuse blowout operation to turn on is out of order The remote is out of order All lights are on due to improper switch-on Lack of water in tank Rupture in tube, and the plug is connected well Main unit is not placed high enough The tube is connected to the inlet for warm water Fan doesn t work No water flows into mattress; the tube bends Lack of water inside main unit with noise Approaches Check the socket and check if the electricity is available Plug the socket well, replace the fuse Cut off the power and reconnect The battery is short of electricity, and change the battery Cut off the power; wipe dry the panel of main unit and turn on the machine again Refill the tank Turn off main unit and check where the leakage happens Place main unit 20CM above mattress Connect the tube to the inlet for cool water Check if there is obstruction blocking the fan, and cleanse it Straighten the tube Add water till the maximum water level - 7 -

8 Failure to heat up or heating effect is poor Dirt build up too much in curtain or channel The tube is connected to the inlet for cool water No water flows into mattress; the tube bends The pump doesn t work Improper temperature setting Lack of water inside main unit with noise Screw the net in the back, and cleanse the dirt Connect the tube to the inlet for warm water Straighten the tube Turn on main unit at interval of 3-5 minutes for multiple times, Reset the temperature Add water till the maximum water level VII Daily maintenance and cleansing 1. For the convenience of cleansing, put a bed sheet on the blanket and meanwhile pointy objects should not be used in case of rupturing the mattress. 2. This product has intelligent water warning system. The signal light is on for lack of water in the tank and the machine stops working, so water needs refill to make it start again. 3. This product has overheated protection. When temperature reach more than 65 C, power would be cut off automatically to avoid scalding, and further check and consultation with manufacturing company are needed when this happens. 4. To avoid getting a cold, please choose proper lever or suitable temperature. Adjust your usage based on your own actual experience, for instance, put a mat or blanket. 5. Conduct maintenance on a regular basis. After one-month usage, it is required to change water machine and all the water inside mattress (discharge and add water for 2 to 3 times). Cleanse the dirt in channel and curtain to guarantee cooling effect of the machine. Make sure you cut off the power when you change water and cleanse the machine. 6. If there is water leakage in main unit, stop using it immediately and contact distributors or manufacturing company, do not take it apart by yourself

9 7. If indoor temperature is below 0, discharge the fluid in main unit and mat to prevent machine being damaged 8. If it is not used for a long time, make sure you thoroughly discharge all the water in the machine and blanket. After the blanket dries up, then you can fold it to put it away. VIII After-sale service In the event that this product fails to work, please contact the maintenance department appointed by our company or local service center. We will offer help at your request, thank your for your cooperation. 1. The warranty period for main unit is one year, while for mattress is 3 months as mattress is susceptible to damage and consumption. 2. The date for warranty starts from date of receipt and your should submit purchasing bill. 3. The warranty is not applied to any of the following situation (1)Damage caused by customers improper usage, caring and maintenance (2)Damage as a result of taking the product apart by customers themselves instead of the maintenance department appointed by our Company. (3)Lack of effective purchasing bill and certificate (4)The receipt type fails to match product model or there is alteration. (5)Damage caused by force of majeure - 9 -

10 Warranty Card Name of client address telephone address Product model Name of seller Address of seller Warm line for after-sale service Time for purchasing Bill number All rights Coolbuddy team